Use IS_ERR() and PTR_ERR() instead of PTR_ZRR_OR_ZERO()
to simplify code, avoid redundant paramenter definitions
and judgements.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for following phy-modes: rgmii, rgmii-id, rgmii-txid, rgmii-rxid.
This PHY has an internal RX delay of 1.2ns and no delay for TX.
The pad skew registers allow to set the total TX delay to max 1.38ns and
the total RX delay to max of 2.58ns (configurable 1.38ns + build in
1.2ns) and a minimal delay of 0ns.
According to the RGMII v1.3 specification the delay provided by PCB traces
should be between 1.5ns and 2.0ns. The RGMII v2.0 allows to provide this
delay by MAC or PHY. So, we configure this PHY to the best values we can
get by this HW: TX delay to 1.38ns (max supported value) and RX delay to
1.80ns (best calculated delay)
The phy-modes can still be fine tuned/overwritten by *-skew-ps
device tree properties described in:
Documentation/devicetree/bindings/net/micrel-ksz90x1.txt
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
net/caif/caif_dev.c:410:2-13: WARNING: Assignment of 0/1 to bool
variable
net/caif/caif_dev.c:445:2-13: WARNING: Assignment of 0/1 to bool
variable
net/caif/caif_dev.c:145:1-12: WARNING: Assignment of 0/1 to bool
variable
net/caif/caif_dev.c:223:1-12: WARNING: Assignment of 0/1 to bool
variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For dwmac4, enable VLAN promiscuity when MAC controller is requested to
enter promiscuous mode.
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macvlan_hash_lookup() uses list_for_each_entry_rcu() for traversing
should either under RCU in fast path or the protection of rtnl_mutex.
In the case of holding RTNL, we should add the corresponding lockdep
expression to silence the following false-positive warning:
=============================
WARNING: suspicious RCU usage
5.7.0-rc1-next-20200416-00003-ga3b8d28bc #1 Not tainted
-----------------------------
drivers/net/macvlan.c:126 RCU-list traversed in non-reader section!!
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tests for vrf and xfrms with a second round after adding a
qdisc. There are a few known problems documented with the test
cases that fail. The fix is non-trivial; will come back to it
when time allows.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now it can be seen that the VSC9959 (Felix) switch will not flood
frames if they have a VLAN tag with a PCP of 1-7 (nonzero).
It turns out that Felix is quite different from its cousin, Ocelot, in
that frame flooding can be allowed/denied per traffic class. Where
Ocelot has 1 instance of the ANA_FLOODING register, Felix has 8.
The approach that this driver is going to take is "thanks, but no
thanks". We have no use case of limiting the flooding domain based on
traffic class, so we just want to allow packets to be flooded, no matter
what traffic class they have.
So we copy the line of code from ocelot.c which does the one-shot
initialization of the flooding PGIDs, and we add it to felix.c as well -
except replicated 8 times.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tracepoint support for QRTR with NS as the first candidate. Later on
this can be extended to core QRTR and transport drivers.
The trace_printk() used in NS has been replaced by tracepoints.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/ila/ila_xlat.c:604:0: warning: macro "ILA_HASH_TABLE_SIZE" is not used [-Wunused-macros]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the act_ct SW offload in flowtable, The counter of the conntrack
entry will never update. So update the nf_conn_acct conuter in act_ct
flowtable software offload.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
net: phy: add device-managed devm_mdiobus_register
If there's no special ordering requirement for mdiobus_unregister(),
then driver code can be simplified by using a device-managed version
of mdiobus_register(). Prerequisite is that bus allocation has been
done device-managed too. Else mdiobus_free() may be called whilst
bus is still registered, resulting in a BUG_ON(). Therefore let
devm_mdiobus_register() return -EPERM if bus was allocated
non-managed.
First user of the new functionality is r8169 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function devm_mdiobus_register() to simplify the driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there's no special ordering requirement for mdiobus_unregister(),
then driver code can be simplified by using a device-managed version
of mdiobus_register(). Prerequisite is that bus allocation has been
done device-managed too. Else mdiobus_free() may be called whilst
bus is still registered, resulting in a BUG_ON(). Therefore let
devm_mdiobus_register() return -EPERM if bus was allocated
non-managed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY supports monitoring its die temperature as well as two analog
voltages. Add support for it.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom BCM54140 is a Quad SGMII/QSGMII Copper/Fiber Gigabit
Ethernet transceiver.
This also adds support for tunables to set and get downshift and
energy detect auto power-down.
The PHY has four ports and each port has its own PHY address.
There are per-port registers as well as global registers.
Unfortunately, the global registers can only be accessed by reading
and writing from/to the PHY address of the first port. Further,
there is no way to find out what port you actually are by just
reading the per-port registers. We therefore, have to scan the
bus on the PHY probe to determine the port and thus what address
we need to access the global registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDB (Register Data Base) registers are used on newer Broadcom PHYs. Add
helper to read, write and modify these registers.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
dt-bindings: net: mdio.yaml fixes
This patch series documents some common MDIO devices properties such as
resets (and delays) and broken-turn-around. The second patch also
rephrases some descriptions to be more general towards MDIO devices and
not specific towards Ethernet PHYs.
Changes in v3:
- corrected wording of 'broken-turn-around' in ethernet-phy.yaml and
mdio.yaml, add Andrew's R-b tag to patch #3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of descriptions assume a PHY device, but since this binding
describes a MDIO bus which can have different kinds of MDIO devices
attached to it, rephrase some descriptions to be more general in that
regard.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the properties pertaining to the broken turn around or resets
were only documented in ethernet-phy.yaml while they are applicable
across all MDIO devices and not Ethernet PHYs specifically which are a
superset.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The turn around bytes (2) are placed between the control phase of the
MDIO transaction and the data phase, correct the wording to be more
exact.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean says:
====================
Ocelot MAC_ETYPE tc-flower key improvements
As discussed in the comments surrounding this patch:
https://patchwork.ozlabs.org/project/netdev/patch/20200417190308.32598-1-olteanv@gmail.com/
the restrictions imposed on non-MAC_ETYPE rules were harsher than they
needed to be. IP, IPv6, ARP rules can still be added concurrently with
src_mac and dst_mac rules, as long as those MAC address rules do not ask
for an offending EtherType.
For that to actually be supported, we need to parse the EtherType from
the flower classification rule first.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
An attempt was made in commit fe3490e610 ("net: mscc: ocelot: Hardware
ofload for tc flower filter") to avoid clashes between MAC_ETYPE rules
and IP rules. Because the protocol blacklist should have included
ETH_P_ALL too, it created some confusion, but now the situation should
be dealt with a bit better by the patch immediately previous to this one
("net: mscc: ocelot: refine the ocelot_ace_is_problematic_mac_etype
function").
So now we can remove that check. MAC_ETYPE rules with a protocol of
ETH_P_IP, ETH_P_IPV6, ETH_P_ARP and ETH_P_ALL _are_ supported, with some
restrictions regarding per-port exclusivity which are enforced now.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit mentioned below was a bit too harsh, and while it restricted
the invalid key combinations which are known to not work, such as:
tc filter add dev swp0 ingress proto ip \
flower src_ip 192.0.2.1 action drop
tc filter add dev swp0 ingress proto all \
flower src_mac 00:11:22:33:44:55 action drop
it also restricted some which still should work, such as:
tc filter add dev swp0 ingress proto ip \
flower src_ip 192.0.2.1 action drop
tc filter add dev swp0 ingress proto 0x22f0 \
flower src_mac 00:11:22:33:44:55 action drop
What actually does not match "sanely" is a MAC_ETYPE rule on frames
having an EtherType of ARP, IPv4, IPv6, in addition to SNAP and OAM
frames (which the ocelot tc-flower implementation does not parse yet, so
the function might need to be revisited again in the future).
So just make the function recognize the problematic MAC_ETYPE rules by
EtherType - thus the VCAP IS2 can be forced to match even on those
packets.
This patch makes it possible for IP rules to live on a port together
with MAC_ETYPE rules that are non-all, non-arp, non-ip and non-ipv6.
Fixes: d4d0cb741d7b ("net: mscc: ocelot: deal with problematic MAC_ETYPE VCAP IS2 rules")
Reported-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the filter's protocol is ignored except for a few special
cases (IPv4 and IPv6).
The EtherType can be matched inside VCAP IS2 by using a MAC_ETYPE key.
So there are 2 cases in which EtherType matches are supported:
- As part of a larger MAC_ETYPE rule, such as:
tc filter add dev swp0 ingress protocol ip \
flower skip_sw src_mac 42:be:24:9b:76:20 action drop
- Standalone (matching on protocol only):
tc filter add dev swp0 ingress protocol arp \
flower skip_sw action drop
As before, if the protocol is not specified, is it implicitly "all" and
the EtherType mask in the MAC_ETYPE half key is set to zero.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yangbo Lu says:
====================
Support programmable pins for Ocelot PTP driver
The Ocelot PTP clock driver had been embedded into ocelot.c driver.
It had supported basic gettime64/settime64/adjtime/adjfine functions
by now which were used by both Ocelot switch and Felix switch.
This patch-set is to move current ptp clock code out of ocelot.c driver
maintaining as a single ocelot_ptp.c driver, and to implement 4
programmable pins with only PTP_PF_PEROUT function for now.
The PTP_PF_EXTTS function will be supported in the future, and it should
be implemented separately for Felix and Ocelot, because of different
hardware interrupt implementation in them.
Changes for v2:
- Put PTP driver under drivers/net/ethernet/mscc/.
- Dropped MAINTAINERS patch. Kept original maintaining.
- Initialized PTP separately in ocelot/felix platforms.
- Supported PPS case in programmable pin.
- Supported disabling pin function since deadlock is fixed by Richard.
- Returned -EBUSY if not finding pin available.
Changes for v3:
- Re-sent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Support 4 PTP programmable pins with only PTP_PF_PEROUT function
for now. The PTP_PF_EXTTS function will be supported in the
future, and it should be implemented separately for Felix and
Ocelot, because of different hardware interrupt implementation
in them.
Since the hardware is not able to support absolute start time,
the periodic clock request only allows start time 0 0. But nsec
could be accepted for PPS case for phase adjustment.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wave programming registers definitions for Ocelot platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 5 PTP_PINS register groups on Ocelot switch.
Except the one used for TOD operations, there are still
4 register groups for programmable pins. So redefine the
4 programmable pins.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timestamp info should be only software timestamp capabilities
if ptp clock does not work.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ocelot PTP clock driver had been embedded into ocelot.c driver.
It had supported basic gettime64/settime64/adjtime/adjfine functions
by now which were used by both Ocelot switch and Felix switch.
This patch is to move current ptp clock code out of ocelot.c driver
maintaining as a single ocelot_ptp.c.
For futher new features implementation, the common code could be put
in ocelot_ptp.c and the switch specific code should be in specific
switch driver. The interrupt implementation in SoC is different
between Ocelot and Felix.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leon Romanovsky says:
====================
Remove vermagic header from global include folder
Changelog:
v2:
* Changed the implementation of patch #4 to be like Masahiro wants.
I personally don't like this implementation and changing it just to move forward
this this patchset.
v1:
https://lore.kernel.org/lkml/20200415133648.1306956-1-leon@kernel.org
* Added tags
* Updated patch #4 with test results
* Changed scripts/mod/modpost.c to create inclusion of vermagic.h
from kernel folder and not from general include/linux. This is
needed to generate *.mod.c files, while building modules.
v0:
https://lore.kernel.org/lkml/20200414155732.1236944-1-leon@kernel.org
This is followup to the failure reported by Borislav [1] and suggested
fix later on [2].
The series removes all includes of linux/vermagic.h, updates hns and
nfp to use same kernel versioning scheme (exactly like we did for
other drivers in previous cycle) and removes vermagic.h from global
include folder.
[1] https://lore.kernel.org/lkml/20200411155623.GA22175@zn.tnic
[2] https://lore.kernel.org/lkml/20200413080452.GA3772@zn.tnic
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
VERMAGIC* definitions are not supposed to be used by the drivers,
see this [1] bug report, so introduce special define to guard inclusion
of this header file and define it in kernel/modules.h and in internal
script that generates *.mod.c files.
In-tree module build:
➜ kernel git:(vermagic) ✗ make clean
➜ kernel git:(vermagic) ✗ make M=drivers/infiniband/hw/mlx5
➜ kernel git:(vermagic) ✗ modinfo drivers/infiniband/hw/mlx5/mlx5_ib.ko
filename: /images/leonro/src/kernel/drivers/infiniband/hw/mlx5/mlx5_ib.ko
<...>
vermagic: 5.6.0+ SMP mod_unload modversions
Out-of-tree module build:
➜ mlx5 make -C /images/leonro/src/kernel clean M=/tmp/mlx5
➜ mlx5 make -C /images/leonro/src/kernel M=/tmp/mlx5
➜ mlx5 modinfo /tmp/mlx5/mlx5_ib.ko
filename: /tmp/mlx5/mlx5_ib.ko
<...>
vermagic: 5.6.0+ SMP mod_unload modversions
[1] https://lore.kernel.org/lkml/20200411155623.GA22175@zn.tnic
Reported-by: Borislav Petkov <bp@suse.de>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Jessica Yu <jeyu@kernel.org>
Co-developed-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change nfp driver to use globally defined kernel version.
Reported-by: Borislav Petkov <bp@suse.de>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use globally defined kernel version instead of custom driver variant.
Reported-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of linux/vermagic.h includes, so that MODULE_ARCH_VERMAGIC from
the arch header arch/x86/include/asm/module.h won't be redefined.
In file included from ./include/linux/module.h:30,
from drivers/net/ethernet/3com/3c515.c:56:
./arch/x86/include/asm/module.h:73: warning: "MODULE_ARCH_VERMAGIC"
redefined
73 | # define MODULE_ARCH_VERMAGIC MODULE_PROC_FAMILY
|
In file included from drivers/net/ethernet/3com/3c515.c:25:
./include/linux/vermagic.h:28: note: this is the location of the
previous definition
28 | #define MODULE_ARCH_VERMAGIC ""
|
Fixes: 6bba2e89a8 ("net/3com: Delete driver and module versions from 3com drivers")
Co-developed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Shannon Nelson <snelson@pensando.io> # ionic
Acked-by: Sebastian Reichel <sre@kernel.org> # power
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable rc is being assigned with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Shevchenko says:
====================
net: bcmgenet: Clean up after ACPI enablement
ACPI enablement series had missed some clean ups that would have been done
at the same time. Here are these bits.
In v2:
- return dev_dbg() calls to avoid spamming logs when probe is deferred (Florian)
- added Ack (Florian)
- combined two, earlier sent, series together
- added couple more patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to have parentheses around plain pointer variable or
negation operator. Drop them for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's convenient to use get_unligned_beXX() and put_unaligned_beXX() helpers
to get or set MAC instead of open-coded variants.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conversion to devm_clk_get_optional() makes it explicit that clocks are
optional. This change allows to handle deferred probe in case clocks are
defined, but not yet probed. Due to above changes bail out in error case.
While here, check potential error when enable main clock.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing which needs a set of OF headers, followed by redundant
OF node ID check. Drop them for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When compiled with CONFIG_ACPI=n, ACPI_PTR() will be no-op, and thus
genet_acpi_match table defined, but not used. Compiler is not happy about
such data. Drop ACPI_PTR() for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes misc updates and clean ups to mlx5 driver:
1) improve some comments from Hu Haowen.
2) Handles errors of netif_set_real_num_{tx,rx}_queues, from Maxim
3) IPsec and FPGA related code cleanup to prepare for ASIC devices
IPsec offloads, from Raed
4) Allow partial mask for tunnel options, from Roi.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl6eEhUACgkQSD+KveBX
+j6rXAf/flM2mYB8moFIqmsSgO6yDnskK9InshCcidM3gqv989dyms1NStv4SzEq
U2zQLGTinlGHEkCW6BJtMQYGatGRIX9DcpZUGYQqSL18ihZ9HkB5R+Dfw8+jRDTI
AIyYoAjpmnAahzJ9xbqtzMPzunlCahdzmfuNjw6mA4QterlllOc5HLqrCi/Rk93Z
WNCo0WRH+6ZfGoC9em/C73n1WDb990QOl51L+8/iSNcuMCeN74Vo5Bs/lJaEKGeV
DQxiE3/wijWmdpBBeVJgXPFKT10W5aPlt7DuYWvTwVJcwtIV3KFrIP5prtHuu4w1
nv09RVihQkGloSzZeM9XHNX0WU4nVg==
=Q2sm
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2020-04-20' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-04-20
This series includes misc updates and clean ups to mlx5 driver:
1) improve some comments from Hu Haowen.
2) Handles errors of netif_set_real_num_{tx,rx}_queues, from Maxim
3) IPsec and FPGA related code cleanup to prepare for ASIC devices
IPsec offloads, from Raed
4) Allow partial mask for tunnel options, from Roi.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A barrier is needed here to ensure that rtl_tx sees the descriptor
changes (DescOwn set) before the updated tp->cur_tx value. Else it may
wrongly assume that the transfer has been finished already. For this
purpose smp_wmb() is sufficient.
No separate barrier is needed for ordering the descriptor changes
with the MMIO doorbell write. The needed barrier is included in
the non-relaxed writel() used by rtl8169_doorbell().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Embedded CPU bit doesn't change with PCI resume/suspend.
Hence read it only once while probing the PCI device.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
netif_set_real_num_tx_queues and netif_set_real_num_rx_queues may fail.
Now that mlx5e supports handling errors in the preactivate hook, this
commit leverages that functionality to handle errors from those
functions and roll back all changes on failure.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We use mapping to save and restore the tunnel options.
Save also the tunnel options mask.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Tang Bin