Prepare for 8250 split; separate RSA probe and resource management
from base port operations. Override base port operations for the
config_port(), request_port() and release_port() methods to
implement the optional RSA probe and resource management only in
the universal/legacy 8250 driver.
Introduce 'probe' flags for 8250 ports, which allows drivers higher
up the driver stack to enable optional probes.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for 8250_core.c file split; move shared inline function
to local header file.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following sparse warnings:
drivers/tty/serial/8250/8250_core.c:3231:32: warning: incorrect type in assignment (different base types)
drivers/tty/serial/8250/8250_core.c:3231:32: expected restricted upf_t [usertype] flags
drivers/tty/serial/8250/8250_core.c:3231:32: got unsigned int const [unsigned] flags
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fixed a sparse warning in 8250_core.c :
incorrect type in assignment (different address spaces)
the warning was because an unsigned char pointer was being assigned to
a pointer of unsigned char __iomem type .
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have (or will have) custom DMA callbacks in the omap driver due to
the different behaviour in the RX and TX case. To make this work
we need a few changes in the IRQ handler to invoke the rx_handler again
after the "manual" mode or retry the tx_handler again before falling
back to the manual mode.
Heikki didn't want to see the extra hacks in the generic / default irq
handler and Peter wasn't too happy about an OMAP-only IRQ handler. The
way I planned it is to use this extra IRQ routine only in DMA case. If
Peter dislike this approach then I hope Heikki doesn't block changes in
the default IRQ handler :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP has a few corner cases where it needs a share of kindness of
affection to do the right thing. Heikki Krogerus suggested that instead
adding the quirks into the default DMA implementation, OMAP could get
its own copy of the function. And Alan suggested the same thing so here
we go.
This patch provides callbacks for custom TX/RX DMA implementation. If
there are not setup / used, then the default (current) implementation is
used.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After dmaengine_terminate_all() has been invoked then both DMA drivers
(edma and omap-dma) do not invoke dma_cookie_complete() to mark the
transfer as complete. This dma_cookie_complete() is performed by the
Synopsys DesignWare driver which is probably the only one that is used
by omap8250-dma and hence don't see following problem…
…which is that once a RX transfer has been terminated then following
query of channel status reports DMA_IN_PROGRESS (again: the actual
transfer has been canceled, there is nothing going on anymore).
This means that serial8250_rx_dma() never enqueues another DMA transfer
because it (wrongly) assumes that there is a transer already pending.
Vinod Koul refuses to accept a patch which adds this
dma_cookie_complete() to both drivers and so dmaengine_tx_status() would
report DMA_COMPLETE instead (and behave like the Synopsys DesignWare
driver already does). He argues that I am not allowed to use the cookie
to query the status and that the driver already cleaned everything up after
the invokation of dmaengine_terminate_all().
To end this I add a bookkeeping whether or not a RX-transfer has been
started to the 8250-dma code. It has already been done for the TX side.
*Now* we learn about the RX status based on our bookkeeping and don't
need dmaengine_tx_status() for this anymore.
Cc: vinod.koul@intel.com
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now it is possible that serial8250_tx_dma() fails and returns
-EBUSY. The caller (serial8250_start_tx()) will then enable
UART_IER_THRI which will generate an interrupt once the TX FIFO is
empty.
In serial8250_handle_irq() nothing will happen because up->dma is set
and so serial8250_tx_chars() won't be invoked. We end up with plenty of
interrupts and some "too much work for irq" output.
This patch introduces dma_tx_err in struct uart_8250_port to signal that
the last invocation of serial8250_tx_dma() failed so we can fill the TX
FIFO manually. Should the next invocation of serial8250_start_tx()
succeed then the dma_tx_err flag along with the THRI bit is removed and
DMA only usage may continue.
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
While comparing the OMAP-serial and the 8250 part of this I noticed that
the latter does not use run time-pm. Here are the pieces. It is
basically a get before first register access and a last_busy + put after
last access. This has to be enabled from userland _and_ UART_CAP_RPM is
required for this.
The runtime PM can usually work transparently in the background however
there is one exception to this: After serial8250_tx_chars() completes
there still may be unsent bytes in the FIFO (depending on CPU speed vs
baud rate + flow control). Even if the TTY-buffer is empty we do not
want RPM to disable the device because it won't send the remaining
bytes. Instead we leave serial8250_tx_chars() with RPM enabled and wait
for the FIFO empty interrupt. Once we enter serial8250_tx_chars() with
an empty buffer we know that the FIFO is empty and since we are not going
to send anything, we can disable the device.
That xchg() is to ensure that serial8250_tx_chars() can be called
multiple times and only the first invocation will actually invoke the
runtime PM function. So that the last invocation of __stop_tx() will
disable runtime pm.
NOTE: do not enable RPM on the device unless you know what you do! If
the device goes idle, it won't be woken up by incomming RX data _unless_
there is a wakeup irq configured which is usually the RX pin configure
for wakeup via the reset module. The RX activity will then wake up the
device from idle. However the first character is garbage and lost. The
following bytes will be received once the device is up in time. On the
beagle board xm (omap3) it takes approx 13ms from the first wakeup byte
until the first byte that is received properly if the device was in
core-off.
v5…v8:
- drop RPM from serial8250_set_mctrl() it will be used in
restore path which already has RPM active and holds
dev->power.lock
v4…v5:
- add a wrapper around rpm function and introduce UART_CAP_RPM
to ensure RPM put is invoked after the TX FIFO is empty.
v3…v4:
- added runtime to the console code
- removed device_may_wakeup() from serial8250_set_sleep()
Cc: mika.westerberg@linux.intel.com
Reviewed-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That field has been deprecated in favour of getting the necessary information
from ACPI or DT.
However, we still need to deal systems that are PCI only (no ACPI to back up)
like Intel Bay Trail. In order to support such systems, we explicitly bind
setup() to the appropriate DMA filter function and its corresponding parameter.
Then when serial8250_request_dma() doesn't find the channel via ACPI or DT, it
falls back to use the given filter function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is no way to access a struct uart_8250_port for a specific
line. This is only required outside of the 8250/uart callbacks like for
devices' suspend & remove callbacks. For those the 8250-core provides a
wrapper like serial8250_unregister_port() which passes the struct
to the proper function based on the line argument.
For run time suspend I need access to this struct not only to make
serial_out() work but also to properly restore up->ier and up->mcr.
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add tunable RX interrupt trigger I/F of FIFO buffers.
Serial devices are used as not only message communication devices but control
or sending communication devices. For the latter uses, normally small data
will be exchanged, so user applications want to receive data unit as soon as
possible for real-time tendency. If we have a sensor which sends a 1 byte data
each time and must control a device based on the sensor feedback, the RX
interrupt should be triggered for each data.
According to HW specification of serial UART devices, RX interrupt trigger
can be changed, but the trigger is hard-coded. For example, RX interrupt trigger
in 16550A can be set to 1, 4, 8, or 14 bytes for HW, but current driver sets
the trigger to only 8bytes.
This patch makes some devices change RX interrupt trigger from userland.
<How to use>
- Read current setting
# cat /sys/class/tty/ttyS0/rx_trig_bytes
8
- Write user setting
# echo 1 > /sys/class/tty/ttyS0/rx_trig_bytes
# cat /sys/class/tty/ttyS0/rx_trig_bytes
1
<Support uart devices>
- 16550A and Tegra (1, 4, 8, or 14 bytes)
- 16650V2 (8, 16, 24, or 28 bytes)
- 16654 (8, 16, 56, or 60 bytes)
- 16750 (1, 16, 32, or 56 bytes)
<Change log>
Changes in V9:
- Use attr_group instead of dev_spec_attr_group of uart_port structure
Changes in V8:
- Divide this patch from V7's patch based on Greg's comment
Changes in V7:
- Add Documentation
- Change I/F name from rx_int_trig to rx_trig_bytes because the name
rx_int_trig is hard to understand how users specify the value
Changes in V6:
- Move FCR_RX_TRIG_* definition in 8250.h to include/uapi/linux/serial_reg.h,
rename those to UART_FCR_R_TRIG_*, and use UART_FCR_TRIGGER_MASK to
UART_FCR_R_TRIG_BITS()
- Change following function names:
convert_fcr2val() => fcr_get_rxtrig_bytes()
convert_val2rxtrig() => bytes_to_fcr_rxtrig()
- Fix typo in serial8250_do_set_termios()
- Delete the verbose error message pr_info() in bytes_to_fcr_rxtrig()
- Rename *rx_int_trig/rx_trig* to *rxtrig* for several functions or variables
(but UI remains rx_int_trig)
- Change the meaningless variable name 'val' to 'bytes' following functions:
fcr_get_rxtrig_bytes(), bytes_to_fcr_rxtrig(), do_set_rxtrig(),
do_serial8250_set_rxtrig(), and serial8250_set_attr_rxtrig()
- Use up->fcr in order to get rxtrig_bytes instead of rx_trig_raw in
fcr_get_rxtrig_bytes()
- Use conf_type->rxtrig_bytes[0] instead of switch statement for support check
in register_dev_spec_attr_grp()
- Delete the checking whether a user changed FCR or not when minimum buffer
is needed in serial8250_do_set_termios()
Changes in V5.1:
- Fix FCR_RX_TRIG_MAX_STATE definition
Changes in V5:
- Support Tegra, 16650V2, 16654, and 16750
- Store default FCR value to up->fcr when the port is first created
- Add rx_trig_byte[] in uart_config[] for each device and use rx_trig_byte[]
in convert_fcr2val() and convert_val2rxtrig()
Changes in V4:
- Introduce fifo_bug flag in uart_8250_port structure
This is enabled only when parity is enabled and UART_BUG_PARITY is enabled
for up->bugs. If this flag is enabled, user cannot set RX trigger.
- Return -EOPNOTSUPP when it does not support device at convert_fcr2val() and
at convert_val2rxtrig()
- Set the nearest lower RX trigger when users input a meaningless value at
convert_val2rxtrig()
- Check whether p->fcr is existing at serial8250_clear_and_reinit_fifos()
- Set fcr = up->fcr in the begging of serial8250_do_set_termios()
Changes in V3:
- Change I/F from ioctl(2) to sysfs(rx_int_trig)
Changed in V2:
- Use _IOW for TIOCSFIFORTRIG definition
- Pass the interrupt trigger value itself
Signed-off-by: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for the WindRiver SBC8560 board was removed in v3.6. But there
are still a few lines depending on its obsolete Kconfig macro. Remove
these now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the UART device present in Broadcom TruManage capable
NetXtreme chips (ie: 5761m 5762, and 5725).
This implementation has a hidden transmit FIFO, so running in single-byte
interrupt mode results in too many interrupts. The UART_CAP_HFIFO
capability was added to track this. It continues to reload the THR as long
as the THRE and TSRE bits are set in the LSR up to a specified limit (1024
is used here).
Signed-off-by: Stephen Hurd <shurd@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for dmaengine API. The drivers can implement the
struct uart_8250_dma member in struct uart_8250_port and
8250.c can take care of the rest.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows us to get rid of the ifdefs in 8250.c.
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We first probe the legacy serial ports and then check pnp. If there
is a non-standard configuration then this might not work, also this
change is needed so we can blacklist Winbond CIR based on PNP ID.
For this to work the 8250_pnp driver must be merged into the 8250
module.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure might have made sense many years ago, but at this
point it is only used in one specific driver, and referenced in
stale comments elsewhere. Rather than change the sunsu.c driver,
simply move the struct to be within the exclusive domain of that
driver, so it won't get inadvertently picked up and used by other
serial drivers going forward. The comments referencing the now
driver specific struct are updated accordingly.
Note that 8250.c has a struct that is similar in usage, with the
name serial8250_config; but is 100% independent and untouched here.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the differences between the original 8250 patch, the revised 8250 patch
and the independant clean up of the octeon driver (to use platform devices properly yay!)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Information and a different patch provided by <donald@asix.com.tw>. We do
it a little differently to keep the modularity and to avoid playing with
RLSI.
We add a new uart bug for the parity flaw and set it in the pci matches.
If parity check is enabled then we drop the FIFO trigger to 1 as per the
Asix reference code.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert serial_dl_read() and serial_dl_write() from macro
to 8250 specific callbacks. This change makes it easier to
support 8250 hardware with non-standard DLL and DLM register
configurations such as Alchemy, RM9K and upcoming Emma Mobile
UART hardware.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using Serial Over Lan (SOL) over the virtual serial port in a Intel
management engine (ME) device, on device reset the serial FIFOs need to
be cleared to keep the FIFO indexes in-sync between the host and the
engine.
On a reset the serial device assertes BI, so using that as a cue FIFOs
are cleared. So for this purpose a new handle_break callback has been
added. One other problem is that the serial registers might temporarily
go to 0 on reset of this device. So instead of using the IER register
read, if 0 returned use the ier value in uart_8250_port. This is hidden
under a custom serial_in.
Cc: Nhan H Mai <nhan.h.mai@intel.com>
Signed-off-by: Sudhakar Mamillapalli <sudhakar@fb.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently 8250.c has serial_in and serial_out as shortcuts
to doing the port I/O. They are implemented as macros a
ways down in the file. This isn't by accident, but is
implicitly required, so cpp doesn't mangle other instances
of the common string "serial_in", as it exists as a field
in the port struct itself.
The above mangling avoidance violates the principle of least
surprise, and it also prevents the shortcuts from being
relocated up to the top of file, or into 8250.h -- either
being a better location than the current one.
Move them to 8250.h so other 8250-like drivers can also use
the shortcuts, and in the process, make the conflicting
names go away by using static inlines instead of macros.
The object file size remains unchanged with this modification.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The drivers/tty/serial dir is already getting rather busy.
Relocate the 8250 related drivers to their own subdir to
reduce the clutter.
Note that sunsu.c is not included in this move -- it is
8250-like hardware, but it does not use any of the existing
infrastructure -- and does not depend on SERIAL_8250.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Peter Hurley