This fixes a race condition where the channel resources could be freed
before the ISR had finished running resulting in a NULL pointer
reference from the ISR.
[ 167.148934] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 167.157051] pgd = ffff80003c641000
[ 167.160449] [00000000] *pgd=000000007c507003, *pud=000000007c4ff003, *pmd=0000000000000000
[ 167.168719] Internal error: Oops: 96000046 [#1] PREEMPT SMP
[ 167.174289] Modules linked in:
[ 167.177348] CPU: 3 PID: 10547 Comm: dma_ioctl Not tainted 4.11.0-rc1-00001-g8d92afddc2f6633a #73
[ 167.186131] Hardware name: Renesas Salvator-X board based on r8a7795 (DT)
[ 167.192917] task: ffff80003a411a00 task.stack: ffff80003bcd4000
[ 167.198850] PC is at rcar_dmac_chan_prep_sg+0xe0/0x400
[ 167.203985] LR is at rcar_dmac_chan_prep_sg+0x48/0x400
Based of previous work by:
Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Implement the device_synchronize() callback which wait until a dma
channel is stopped to provide a synchronization point.
This protects the driver from multiple race conditions when terminating
and freeing resources. E.g. the completion callback still running after
device_terminate_all() has completed.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The IRQ number is needed after probe to be able to add synchronisation
points in other places in the driver when freeing resources and to
implement a device_synchronize() callback. Store the IRQ number in the
struct rcar_dmac_chan so that it can be used later.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Req is never null on at the point of the null check, so
remove this redundant check and just return &req->tx.
Detected by CoverityScan, CID#1436147 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The new driver requires both mailbox and raid support for compile
testing:
drivers/dma/built-in.o: In function `sba_remove':
edma.c:(.text+0x4414): undefined reference to `mbox_free_channel'
drivers/dma/built-in.o: In function `sba_issue_pending':
edma.c:(.text+0x46cc): undefined reference to `mbox_send_message'
drivers/dma/built-in.o: In function `sba_probe':
edma.c:(.text+0x4e60): undefined reference to `mbox_request_channel'
edma.c:(.text+0x5038): undefined reference to `mbox_free_channel'
drivers/dma/built-in.o: In function `sba_tx_status':
edma.c:(.text+0x5210): undefined reference to `mbox_client_peek_data'
drivers/dma/built-in.o: In function `sba_prep_dma_pq_req':
edma.c:(.text+0x5784): undefined reference to `raid6_gflog'
edma.c:(.text+0x5798): undefined reference to `raid6_gflog'
This rearranges the Kconfig dependencies accordingly.
Fixes: 743e1c8ffe ("dmaengine: Add Broadcom SBA RAID driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The Broadcom stream buffer accelerator (SBA) provides offloading
capabilities for RAID operations. This SBA offload engine is
accessible via Broadcom SoC specific ring manager.
This patch adds Broadcom SBA RAID driver which provides one
DMA device with RAID capabilities using one or more Broadcom
SoC specific ring manager channels. The SBA RAID driver in its
current shape implements memcpy, xor, and pq operations.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
AVR32 is gone. Now it's time to clean up the driver by removing
leftovers that was used by AVR32 related code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds the support for suspend/resume in the mv_xor_v2
driver. The suspend suspend function disables the XOR engine after the
DMA stack has handled all pending descriptors in the queue. The resume
function re-configures the XOR engine and re-enables the engine.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Remove unnecessary write to DESQ_STOP register, this register is used to
enable or disable the XOR engine, and not to issue all pending
descriptors in the queue. mv_xor_v2 driver already writes to this
register and enable XOR engine in the mv_xor_v2_descq_init() function,
called during initialization.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Until now, the driver was not using interrupt coalescing: one interrupt
was generated for each descriptor processed by the XOR engine. This
commit changes that by using the interrupt coalescing features of the
hardware, by setting both a number of descriptors processed before an
interrupt is generated and a timeout before an interrupt is generated.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The XORv2 engine on Armada 7K/8K can only access the first 40 bits of
the physical address space, so the DMA mask must be set accordingly.
Fixes: 19a340b1a8 ("dmaengine: mv_xor_v2: new driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The current implementation of interrupt coalescing doesn't work, because
it doesn't configure the coalescing timer, which is needed to make sure
we get an interrupt at some point.
As a fix for stable, we simply remove the interrupt coalescing
functionality. It will be re-introduced properly in a future commit.
Fixes: 19a340b1a8 ("dmaengine: mv_xor_v2: new driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The mv_xor_v2_tx_submit() gets the next available HW descriptor by
calling mv_xor_v2_get_desq_write_ptr(), which reads a HW register
telling the next available HW descriptor. This was working fine when HW
descriptors were issued for processing directly in tx_submit().
However, as part of the review process of the driver, a change was
requested to move the actual kick-off of HW descriptors processing to
->issue_pending(). Due to this, reading the HW register to know the next
available HW descriptor no longer works.
So instead of using this HW register, we implemented a software index
pointing to the next available HW descriptor.
Fixes: 19a340b1a8 ("dmaengine: mv_xor_v2: new driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The engine was enabled prior to its configuration, which isn't
correct. This patch relocates the activation of the XOR engine, to be
after the configuration of the XOR engine.
Fixes: 19a340b1a8 ("dmaengine: mv_xor_v2: new driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Descriptors that have not been acknowledged by the async_tx layer
should not be re-used, so this commit adjusts the implementation of
mv_xor_v2_prep_sw_desc() to skip descriptors for which
async_tx_test_ack() is false.
Fixes: 19a340b1a8 ("dmaengine: mv_xor_v2: new driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
mv_xor_v2_tasklet() is looping over completed HW descriptors. Before the
loop, it initializes 'next_pending_hw_desc' to the first HW descriptor
to handle, and then the loop simply increments this point, without
taking care of wrapping when we reach the last HW descriptor. The
'pending_ptr' index was being wrapped back to 0 at the end, but it
wasn't used in each iteration of the loop to calculate
next_pending_hw_desc.
This commit fixes that, and makes next_pending_hw_desc a variable local
to the loop itself.
Fixes: 19a340b1a8 ("dmaengine: mv_xor_v2: new driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The mv_xor_v2_prep_sw_desc() is called from a few different places in
the driver, but we never take into account the fact that it might
return NULL. This commit fixes that, ensuring that we don't panic if
there are no more descriptors available.
Fixes: 19a340b1a8 ("dmaengine: mv_xor_v2: new driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This time again a smaller update consisting of:
- support for TI DA8xx dma controller and updates to the cppi driver
- updates on bunch of drivers like xilinx, pl08x, stm32-dma, mv_xor, ioat,
dmatest
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ygkn
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.12-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time again a smaller update consisting of:
- support for TI DA8xx dma controller and updates to the cppi driver
- updates on bunch of drivers like xilinx, pl08x, stm32-dma, mv_xor,
ioat, dmatest"
* tag 'dmaengine-4.12-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (35 commits)
dmaengine: pl08x: remove lock documentation
dmaengine: pl08x: fix pl08x_dma_chan_state documentation
dmaengine: pl08x: Use the BIT() macro consistently
dmaengine: pl080: Fix some missing kerneldoc
dmaengine: pl080: Cut some unused defines
dmaengine: dmatest: Add check for supported buffer count (sg_buffers)
dmaengine: dmatest: Select DMA_ENGINE_RAID as its needed for the slave_sg test
dmaengine: virt-dma: Convert to use list_for_each_entry_safe()
dma-debug: use offset_in_page() macro
dmaengine: mv_xor: use offset_in_page() macro
dmaengine: dmatest: use offset_in_page() macro
dmaengine: sun4i: fix invalid argument
dmaengine: ioat: use setup_timer
dmaengine: cppi41: Fix an Oops happening in cppi41_dma_probe()
dmaengine: pl330: remove pdata based initialization
dmaengine: cppi: fix build error due to bad variable
dmaengine: imx-sdma: add 1ms delay to ensure SDMA channel is stopped
dmaengine: cppi41: use managed functions devm_*()
dmaengine: cppi41: fix cppi41_dma_tx_status() logic
dmaengine: qcom_hidma: pause the channel on shutdown
...
This makes the driver shift bits with BIT() which is used on other
places in the driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Two elements of the physical channel description was missing.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When using dmatest with sg_buffers=128 I stumbled upon the problem, that
the "map_cnt" variable of "struct dmaengine_unmap_data" was set to 0.
"map_cnt" is an "u8" variable, resulting in an overrun when its
value is set to src_cnt + dst_cnt, to twice the sg_buffer value.
This patch adds a small check to dmatest, so that this confusing error
is detected and the test is aborted.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Kedareswara rao Appana <appanad@xilinx.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
To enable usage of multiple SG buffers via the sg_buffers= module
parameter, lets select DMA_ENGINE_RAID via Kconfig when DMATEST is
configured. Otherwise the dmatest will "BUG" when more than 1
buffer (total of 2 for src + dst) is configured via sg_buffers.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Kedareswara rao Appana <appanad@xilinx.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use list_for_each_entry_safe() instead of open coding variants.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The "pchans_used" field is an unsigned long array.
for_each_clear_bit_from() expects an unsigned long pointer,
not an array address.
$ make C=2 drivers/dma/sun4i-dma.o
CHECK drivers/dma/sun4i-dma.c
drivers/dma/sun4i-dma.c:241:9: warning: incorrect type in argument 1 (different base types)
drivers/dma/sun4i-dma.c:241:9: expected unsigned long const *p
drivers/dma/sun4i-dma.c:241:9: got unsigned long ( *<noident> )[1]
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This fix an Oops happening on all platforms using the old dt bindings
(all platforms but da8xx).
This update cppi41_dma_probe() to use the index variable which is
required to keep compatibility between old and new dt bindings.
Fixes: 8e3ba95f41 ("dmaengine: cppi41: use managed functions devm_*()")
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This driver is now used only on platforms which support device tree, so
it is safe to remove legacy platform data based initialization code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
For plat-samsung:
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 8e3ba95f41 ("dmaengine: cppi41: use managed functions devm_*()")
moved the code to devm_* but erranously changed a varible name, so fix it.
drivers/dma/cppi41.c:1052:5: error: 'struct cppi41_dd' has no member named 'qmrg_mem'
cdd->qmrg_mem = devm_ioremap_resource(dev, mem);
^
drivers/dma/cppi41.c:1053:16: error: 'struct cppi41_dd' has no member named 'qmrg_mem'
if (IS_ERR(cdd->qmrg_mem))
^
drivers/dma/cppi41.c:1054:21: error: 'struct cppi41_dd' has no member named 'qmrg_mem'
return PTR_ERR(cdd->qmrg_mem);
^
Fixes: 8e3ba95f41 ("dmaengine: cppi41: use managed functions devm_*()")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
sdma_disable_channel() cannot ensure dma is stopped to access
module's FIFOs. There is chance SDMA core is running and accessing
BD when disable of corresponding channel, this may cause sometimes
even after call of .sdma_disable_channel(), SDMA core still be
running and accessing module's FIFOs.
According to NXP R&D team a delay of one BD SDMA cost time (maximum
is 1ms) should be added after disable of the channel bit, to ensure
SDMA core has really been stopped after SDMA clients call
.device_terminate_all.
This patch introduces adds a new function sdma_disable_channel_with_delay()
which simply adds 1ms delay after call sdma_disable_channel(),
and set it as .device_terminate_all.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This makes the error handling much more simpler than open-coding
everything and in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It makes sense to set residue when channel is in progress. Otherwise it
should be 0 since transfer is completed. Meanwhile this patch doesn't
prevent to set residue value anyway.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We need to ensure that all DMAs and interrupts are cleared during
shutdown operation in order for kexec to start the next kernel clearly.
Otherwise, HW could be performing a DMA into random addresses in the
middle of second kernel start.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Once the channels are stopped, disable interrupts to make sure no new
HW interaction can happen.
Similarly, re-enable the interrupts only if we know that channel is
operational again.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
SYS-DMAC can use 40bit address transfer, and it supports Descriptor
Mode too. Current SYS-DMAC driver disables Descriptor Mode if it was
40bit address today. But it can use Descriptor Mode with 40bit if
transfer Source/Destination address are located in same 4GiB region
in the 40 bit address space.
This patch enables it if all condition was clear
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The device_prep_dma_memcpy() callback for this driver allocates a new
xilinx_dma_tx_descriptor whose TX segments list is initialized as empty,
but then gets invalid TX segment pointer by list_last_entry() from the
empty TX segments list and memory corruption happens by the attempt to
update the next descriptor in invalid TX segment pointer.
This removes unnecessary memory access for nonexistent tail TX segment
which causes memory corruption.
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Kedareswara rao Appana <appana.durga.rao@xilinx.com>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The device_terminate_all() callback for this driver stops current DMA
operations by clearing RUNSTOP bit in the control register and waiting
HALTED bit set in the status register.
But AXI CDMA which is one of the supported DMA engine by this driver
does not provide the run / stop controls and those bits in the control
and status registers are reserved. So when device_terminate_all() is
called, the error message is printed and the channel is marked as having
errors in xilinx_dma_halt().
This change adds stop_transfer() callback which differentiates CDMA and
other DMA engine. The CDMA's one avoids the unsupported operations and
instead polls the status register to check if the DMA operations are in
progress for AXI CDMA.
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Kedareswara rao Appana <appana.durga.rao@xilinx.com>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This fixes the following warning when building with clang and
CONFIG_DMA_ENGINE_RAID=n :
drivers/dma/dmaengine.c:1102:11: error: array index 2 is past the end of the array (which contains 1 element) [-Werror,-Warray-bounds]
return &unmap_pool[2];
^ ~
drivers/dma/dmaengine.c:1083:1: note: array 'unmap_pool' declared here
static struct dmaengine_unmap_pool unmap_pool[] = {
^
drivers/dma/dmaengine.c:1104:11: error: array index 3 is past the end of the array (which contains 1 element) [-Werror,-Warray-bounds]
return &unmap_pool[3];
^ ~
drivers/dma/dmaengine.c:1083:1: note: array 'unmap_pool' declared here
static struct dmaengine_unmap_pool unmap_pool[] = {
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The SDMA hardware/driver does not actually report the transfer residue at
burst size granularity, but in fact is only able to report residue after
each finished segment.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The check to see if cd is null is redundant, pdata->channels is
never null at this point, and hence &pdata->channels[i] cannot
be null, so remove the null check.
Detected by CoverityScan, CID#1357194 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
During the teardown of a RX channel, because there is only one
completion queue available for RX channel, descriptor of another
channel may be popped which will cause 2 warnings:
- the first one because we popped a wrong descriptor
(neither the channel's descriptor, nor the teardown descriptor).
- the second one happen during the teardown of another channel,
because we can't find the channel descriptor
(that is, the one that caused the first warning).
To avoid that, use one free queue instead of a transmit completion queue.
Note that fix doesn't fix all the teardown warnings:
I still get some when I run some corner case.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The DA8xx has a CPPI 4.1 DMA controller.
This is add the glue layer required to make it work on DA8xx.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
All the platform code to manage IRQ has been moved to MUSB,
and now the interrupt handler is completely generic.
Remove the isr callback that is not useful anymore.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Despite the driver is already using DT to get the number of channels,
init_sched() is using an hardcoded value to get it.
Use DT to get the number of channels.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Some constants are defined and use by the driver whereas they are
specifics to AM335x.
Add new variables to the glue layer, initialize them with the constants,
and use them in the driver.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently, only the AM335x is supported by the driver.
Though the driver has a glue layer to support different platforms,
some platform variable names are not prefixed with the platform name.
To facilitate the addition of a new platform,
rename some variables owned by the AM335x glue.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In order to make CPPI 4.1 DMA driver more generic, accesses to USBSS
have been removed. So it is not required anymore to map the "glue"
register's.
Remove usbss_mem.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Trivial fix to spelling mistake and make channel plural.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The code responsible for splitting periods into chunks that
can be handled by the DMA controller missed to update total_len,
the number of bytes processed in the current period, when there
are more chunks to follow.
Therefore total_len was stuck at 0 and the code didn't work at all.
This resulted in a wrong control block layout and audio issues because
the cyclic DMA callback wasn't executing on period boundaries.
Fix this by adding the missing total_len update.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Tested-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
But first update usage sites with the new header dependency.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Here is the big tty/serial driver patchset for 4.11-rc1.
Not much here, but a lot of little fixes and individual serial driver
updates all over the subsystem. Majority are for the sh-sci driver and
platform (the arch-specific changes have acks from the maintainer).
The start of the "serial bus" code is here as well, but nothing is
converted to use it yet. That work is still ongoing, hopefully will
start to show up across different subsystems for 4.12 (bluetooth is one
major place that will be used.)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWK2lDg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylwfwCgyExa4x8Lur2nZyu8cgcaVRU68VAAoNQh0WJt
EZdEhEkRMt4d64j+ApYI
=iv7x
-----END PGP SIGNATURE-----
Merge tag 'tty-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big tty/serial driver patchset for 4.11-rc1.
Not much here, but a lot of little fixes and individual serial driver
updates all over the subsystem. Majority are for the sh-sci driver and
platform (the arch-specific changes have acks from the maintainer).
The start of the "serial bus" code is here as well, but nothing is
converted to use it yet. That work is still ongoing, hopefully will
start to show up across different subsystems for 4.12 (bluetooth is
one major place that will be used.)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (109 commits)
tty: pl011: Work around QDF2400 E44 stuck BUSY bit
atmel_serial: Use the fractional divider when possible
tty: Remove extra include in HVC console tty framework
serial: exar: Enable MSI support
serial: exar: Move register defines from uapi header to consumer site
serial: pci: Remove unused pci_boards entries
serial: exar: Move Commtech adapters to 8250_exar as well
serial: exar: Fix feature control register constants
serial: exar: Fix initialization of EXAR registers for ports > 0
serial: exar: Fix mapping of port I/O resources
serial: sh-sci: fix hardware RX trigger level setting
tty/serial: atmel: ensure state is restored after suspending
serial: 8250_dw: Avoid "too much work" from bogus rx timeout interrupt
serdev: ttyport: check whether tty_init_dev() fails
serial: 8250_pci: make pciserial_detach_ports() static
ARM: dts: STiH410-b2260: Enable HW flow-control
ARM: dts: STiH407-family: Use new Pinctrl groups
ARM: dts: STiH407-pinctrl: Add Pinctrl group for HW flow-control
ARM: dts: STiH410-b2260: Identify the UART RTS line
dt-bindings: serial: Update 'uart-has-rtscts' description
...
Here is the big USB and PHY driver updates for 4.11-rc1.
Nothing major, just the normal amount of churn in the usb gadget and dwc
and xhci controllers, new device ids, new phy drivers, a new usb-serial
driver, and a few other minor changes in different USB drivers.
All have been in linux-next for a long time with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWK2lrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykh7ACffotTJvB/gwpuSIWh6qhA8KQ9mH8AnjlxMafv
b5b3vfOXJ8/N0Go25VwI
=7fqN
-----END PGP SIGNATURE-----
Merge tag 'usb-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB and PHY driver updates for 4.11-rc1.
Nothing major, just the normal amount of churn in the usb gadget and
dwc and xhci controllers, new device ids, new phy drivers, a new
usb-serial driver, and a few other minor changes in different USB
drivers.
All have been in linux-next for a long time with no reported issues"
* tag 'usb-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (265 commits)
usb: cdc-wdm: remove logically dead code
USB: serial: keyspan: drop header file
USB: serial: io_edgeport: drop io-tables header file
usb: musb: add code comment for clarification
usb: misc: add USB251xB/xBi Hi-Speed Hub Controller Driver
usb: misc: usbtest: remove redundant check on retval < 0
USB: serial: upd78f0730: sort device ids
USB: serial: upd78f0730: add ID for EVAL-ADXL362Z
ohci-hub: fix typo in dbg_port macro
usb: musb: dsps: Manage CPPI 4.1 DMA interrupt in DSPS
usb: musb: tusb6010: Clean up tusb_omap_dma structure
usb: musb: cppi_dma: Clean up cppi41_dma_controller structure
usb: musb: cppi_dma: Clean up cppi structure
usb: musb: cppi41: Detect aborted transfers in cppi41_dma_callback()
usb: musb: dma: Add a DMA completion platform callback
drivers: usb: usbip: Add missing break statement to switch
usb: mtu3: remove redundant dev_err call in get_ssusb_rscs()
USB: serial: mos7840: fix another NULL-deref at open
USB: serial: console: clean up sanity checks
USB: serial: console: fix uninitialised spinlock
...
This time we fairly boring and bit small update.
- Support for Intel iDMA 32-bit hardware
- deprecate broken support for channel switching in async_tx
- bunch of updates on stm32-dma
- Cyclic support for zx dma and making in generic zx dma driver
- Small updates to bunch of other drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJYrI1RAAoJEHwUBw8lI4NHMH4QALbxsOzil+Sl5gq27xK02ox3
8NGkVdAZgUlMI0m7VnPrdenhLy+t7wz383RM0/DUJfHqJItwxdR+895GRwe5TJTl
PJJMrrdURv6k24ZqUq1b8qKN51YOjp9aVX6sjKi531fcf1Cmj6nuquo8/gIlZtQC
GnLPQGqgK/i5EX/LGQwuHw4j6hESsLGu1vCPdJBSRGzlzd6T4rbmc2ApUjSB1PRO
uhmLrORdkbQnxnt1mUYDlEVwGy/0wVNML89k/SX1g/70NI2kvVUn2NX5Aq7+C+vl
iIdBfYXuPDnhygrze8jYNd6acc9MWyKp7uYelTtm+m4tvVMAD2UJS/eXgbgkcyLj
XoGGkfjDLlK40gQDqnWiNfLi+Dn899ZEwXvCZNsQa72RS32wiatu3ZG39x+a55mK
XISolM57iph975C4manY2sxLfOZmM5qmXg8+JGMppine5U2kmID44Y72jYKLNeUU
EjMCVeZidx7LFkAR8BfA5pZt2BBIooHcncIwD9MW9KsEMPqzMcjqg9Wvxn/hSIUu
VGPVnBZrz/IBSeN9sqMmXWVY0kI+teC7bFZHecZBOUylOyxcQ9ZBHT7Ie2wM2piM
fY4UYWTtn9p/YOrfE32iSn226ga6a0Pk1kEfWgOQ/KXmOd20D33z0NYY9xOQ/CXC
aT+Skn10zjYZbfU0MCp5
=pcdH
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.11-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we fairly boring and bit small update.
- Support for Intel iDMA 32-bit hardware
- deprecate broken support for channel switching in async_tx
- bunch of updates on stm32-dma
- Cyclic support for zx dma and making in generic zx dma driver
- Small updates to bunch of other drivers"
* tag 'dmaengine-4.11-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (29 commits)
async_tx: deprecate broken support for channel switching
dmaengine: rcar-dmac: Widen DMA mask to 40 bits
dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
dmaengine: Provide a wrapper for memcpy operations
dmaengine: zx: fix build warning
dmaengine: dw: we do support Merrifield SoC in PCI mode
dmaengine: dw: add support of iDMA 32-bit hardware
dmaengine: dw: introduce register mappings for iDMA 32-bit
dmaengine: dw: introduce block2bytes() and bytes2block()
dmaengine: dw: extract dwc_chan_pause() for future use
dmaengine: dw: replace convert_burst() with one liner
dmaengine: dw: register IRQ and DMA pool with instance ID
dmaengine: dw: Fix data corruption in large device to memory transfers
dmaengine: ste_dma40: indicate granularity on channels
dmaengine: ste_dma40: indicate directions on channels
dmaengine: stm32-dma: Add error messages if xlate fails
dmaengine: dw: pci: remove LPE Audio DMA ID
dmaengine: stm32-dma: Add max_burst support
dmaengine: stm32-dma: Add synchronization support
dmaengine: stm32-dma: Fix residue computation issue in cyclic mode
...
By default, the DMA mask covers only the low 32-bit address space, which
causes SWIOTLB on arm64 to fall back to a bounce buffer for DMA
transfers involving memory outside the 32-bit address space.
The R-Car DMA controller hardware supports a 40-bit address space, hence
widen the DMA mask to 40 bits to actually make use of this feature.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Despite the CPPI 4.1 is a generic DMA, it is tied to USB.
On the DSPS, CPPI 4.1 interrupt's registers are in USBSS (the MUSB glue).
Currently, to enable / disable and clear interrupts, the CPPI 4.1 driver
maps and accesses to USBSS's register, which making CPPI 4.1 driver not
really generic.
Move the interrupt management to DSPS driver.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As 64-bit Allwinner H5 SoC has the same DMA engine with H3, the DMA
driver should be allowed to be built for ARM64, in order to make it work on H5.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The static bug finder EBA (http://www.iagoabal.eu/eba/) reported the
following double-lock bug:
Double lock:
1. spin_lock_irqsave(pch->lock, flags) at pl330_free_chan_resources:2236;
2. call to function `pl330_release_channel' immediately after;
3. call to function `dma_pl330_rqcb' in line 1753;
4. spin_lock_irqsave(pch->lock, flags) at dma_pl330_rqcb:1505.
I have fixed it as suggested by Marek Szyprowski.
First, I have replaced `pch->lock' with `pl330->lock' in functions
`pl330_alloc_chan_resources' and `pl330_free_chan_resources'. This avoids
the double-lock by acquiring a different lock than `dma_pl330_rqcb'.
NOTE that, as a result, `pl330_free_chan_resources' executes
`list_splice_tail_init' on `pch->work_list' under lock `pl330->lock',
whereas in the rest of the code `pch->work_list' is protected by
`pch->lock'. I don't know if this may cause race conditions. Similarly
`pch->cyclic' is written by `pl330_alloc_chan_resources' under
`pl330->lock' but read by `pl330_tx_submit' under `pch->lock'.
Second, I have removed locking from `pl330_request_channel' and
`pl330_release_channel' functions. Function `pl330_request_channel' is
only called from `pl330_alloc_chan_resources', so the lock is already
held. Function `pl330_release_channel' is called from
`pl330_free_chan_resources', which already holds the lock, and from
`pl330_del'. Function `pl330_del' is called in an error path of
`pl330_probe' and at the end of `pl330_remove', but I assume that there
cannot be concurrent accesses to the protected data at those points.
Signed-off-by: Iago Abal <mail@iagoabal.eu>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix build warning that related to PAGE_SIZE. The maximum DMA
length has nothing to do with PAGE_SIZE, just use a fix number
for the definition.
drivers/dma/zx_dma.c: In function 'zx_dma_prep_memcpy':
drivers/dma/zx_dma.c:523:8: warning: division by zero [-Wdiv-by-zero]
drivers/dma/zx_dma.c: In function 'zx_dma_prep_slave_sg':
drivers/dma/zx_dma.c:567:11: warning: division by zero [-Wdiv-by-zero]
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Intel Merrifield platform contains Intel integrated DMA (iDMA 32-bit) which has
a slightly different register mapping, e.g. some bits in CTL_* and CFG_*
channel registers, and has to use platform data since there is no
autoconfiguration.
The iDMA 32-bit specification is available in the publicly available
documentation for Intel Braswell and BayTrail SoCs as LPE Audio DMA.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
iDMA 32-bit is Intel designed DMA controller that behaves like Synopsys
Designware DMA. This patch adds a support of the new Intel hardware.
Due to iDMA 32-bit has no autoconfiguration the platform code must
provide a platform data to dw_dma_probe().
By default full FIFO (1024 bytes) is assigned to channel 0. Here we
slice FIFO on equal parts between channels for iDMA 32-bit case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The integrated DMA (iDMA 32-bit) is Intel designed DMA controller which
mimics Synopsys Designware DMA. This patch appends the register mappings
for the parts which are slightly different to the DesignWare hardware.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The newly introduced helpers prepare driver to support new DMA controller
hardware.
While here, introduce DWC_CTLH_BLOCK_TS() macro as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
iDMA 32-bit has a special handling of the FIFO during pause() /
terminate_all(). Prepare code to implement that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Replace convert_burst() with one liner in place.
The change simplifies further extension of the driver to cover new DMA
controller hardware.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It is really useful not only for debugging to have an IRQ line and DMA
pool labeled with driver and its instance ID. Do this for DesignWare DMA
driver.
All current users of this IP would be enhanced later on.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When transferring more data than the maximum block size supported by the
HW multiplied by source width the transfer is split into smaller chunks.
Currently code calculates the memory width and thus aligment before
splitting for both memory to device and device to memory transfers.
For memory to device transfers this work fine since alignment is preserved
through the splitting and split blocks are still memory width aligned.
However in device to memory transfers aligment breaks when maximum block
size multiplied by register width doesn't have the same alignment than the
buffer. For instance when transferring from an 8-bit register 4100 bytes
(32-bit aligned) on a DW DMA that has maximum block size of 4095 elements.
An attempt to do such transfers caused data corruption.
Fix this by calculating and setting the destination memory width after
splitting by using the split block aligment and length.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
With patches "dmaengine: cppi41: Fix runtime PM timeouts with USB mass
storage", and "dmaengine: cppi41: Fix oops in cppi41_runtime_resume",
the pm_runtime_get/put() in cppi41_irq() is no longer needed. We now
guarantee that cppi41 is enabled when dma is in use.
We can still get pointless error -115 when musb is configured as a
usb peripheral. That's because we should now check for the state of
is_suspended instead.
Let's just remove the now useless code and replace it with a WARN().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit fdea2d09b9 ("dmaengine: cppi41: Add basic PM runtime support")
together with recent MUSB changes allowed USB and DMA on BeagleBone to idle
when no cable is connected. But looks like few corner case issues still
remain.
Looks like just by re-plugging USB cable about ten or so times on BeagleBone
when configured in USB peripheral mode we can get warnings and eventually
trigger an oops in cppi41 DMA:
WARNING: CPU: 0 PID: 14 at drivers/dma/cppi41.c:1154 cppi41_runtime_suspend+
x28/0x38 [cppi41]
...
WARNING: CPU: 0 PID: 14 at drivers/dma/cppi41.c:452
push_desc_queue+0x94/0x9c [cppi41]
...
Unable to handle kernel NULL pointer dereference at virtual
address 00000104
pgd = c0004000
[00000104] *pgd=00000000
Internal error: Oops: 805 [#1] SMP ARM
...
[<bf0d92cc>] (cppi41_runtime_resume [cppi41]) from [<c0589838>]
(__rpm_callback+0xc0/0x214)
[<c0589838>] (__rpm_callback) from [<c05899ac>] (rpm_callback+0x20/0x80)
[<c05899ac>] (rpm_callback) from [<c0589460>] (rpm_resume+0x504/0x78c)
[<c0589460>] (rpm_resume) from [<c058a1a0>] (pm_runtime_work+0x60/0xa8)
[<c058a1a0>] (pm_runtime_work) from [<c0156120>] (process_one_work+0x2b4/0x808)
This is because of a race with runtime PM and cppi41_dma_issue_pending()
as reported by Alexandre Bailon <abailon@baylibre.com> in earlier
set of patches. Based on mailing list discussions we however came to the
conclusion that a different fix from Alexandre's fix is needed in order
to guarantee that DMA is really active when we try to use it.
To fix the issue, we need to add a driver specific flag as we otherwise
can have -EINPROGRESS state set by runtime PM and can't rely on
pm_runtime_active() to tell us when we can use the DMA.
And we need to make sure the DMA transfers get triggered in the queued
order. So let's always queue the transfers, then flush the queue
from both cppi41_dma_issue_pending() and cppi41_runtime_resume()
as suggested by Grygorii Strashko <grygorii.strashko@ti.com> in an
earlier example patch.
For reference, this is also documented in Documentation/power/runtime_pm.txt
in the example at the end of the file as pointed out by Grygorii Strashko
<grygorii.strashko@ti.com>.
Based on earlier patches from Alexandre Bailon <abailon@baylibre.com>
and Grygorii Strashko <grygorii.strashko@ti.com> modified based on
testing and what was discussed on the mailing lists.
Fixes: fdea2d09b9 ("dmaengine: cppi41: Add basic PM runtime support")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Bin Liu <b-liu@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Patrick Titiano <ptitiano@baylibre.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reported-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit fdea2d09b9 ("dmaengine: cppi41: Add basic PM runtime support")
added runtime PM support for cppi41, but had corner case issues. Some of
the issues were fixed with commit 098de42ad6 ("dmaengine: cppi41: Fix
unpaired pm runtime when only a USB hub is connected"). That fix however
caused a new regression where we can get error -115 messages with USB on
BeagleBone when connecting a USB mass storage device to a hub.
This is because when connecting a USB mass storage device to a hub, the
initial DMA transfers can take over 200ms to complete and cppi41
autosuspend delay times out.
To fix the issue, we want to implement refcounting for chan_busy array
that contains the active dma transfers. Increasing the autosuspend delay
won't help as that the delay could be potentially seconds, and it's best
to let the USB subsystem to deal with the timeouts on errors.
The earlier attempt for runtime PM was buggy as the pm_runtime_get/put()
calls could get unpaired easily as they did not follow the state of
the chan_busy array as described in commit 098de42ad6 ("dmaengine:
cppi41: Fix unpaired pm runtime when only a USB hub is connected".
Let's fix the issue by adding pm_runtime_get() to where a new transfer
is added to the chan_busy array, and calls to pm_runtime_put() where
chan_busy array entry is cleared. This prevents any autosuspend timeouts
from happening while dma transfers are active.
Fixes: 098de42ad6 ("dmaengine: cppi41: Fix unpaired pm runtime when
only a USB hub is connected")
Fixes: fdea2d09b9 ("dmaengine: cppi41: Add basic PM runtime support")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Bin Liu <b-liu@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Patrick Titiano <ptitiano@baylibre.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The PL330 is hard-wired such that instruction fetches on both the
manager and channel threads go out onto the bus with the "privileged"
bit set. This can become troublesome once there is an IOMMU or other
form of memory protection downstream, since those will typically be
programmed by the DMA mapping subsystem in the expectation of normal
unprivileged transactions (such as the PL330 channel threads' own data
accesses as currently configured by this driver).
To avoid the case of, say, an IOMMU blocking an unexpected privileged
transaction with a permission fault, use the newly-introduced
DMA_ATTR_PRIVILEGED attribute for the mapping of our microcode buffer.
That way the DMA layer can do whatever it needs to do to make things
continue to work as expected on more complex systems.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mitchel Humpherys <mitchelh@codeaurora.org>
[rm: remove now-redundant local variable, clarify commit message]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Starting from Tangier B0 and continuing on Anniedale the HSU DMA interrupt
line is actually shared with UART. Handling them independently is racy and
quite often comes with the following traceback.
irq 54: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.9.0-rc6-edison64-86244934+ #1
Hardware name: Intel Corporation Merrifield/BODEGA BAY, BIOS 542 2015.01.21:18.19.48
ffff88003f203eb0 ffffffff8130e718 ffff880032627000 ffff88003262709c
ffff88003f203ed8 ffffffff810a3960 ffff880032627000 0000000000000000
ffff880032627000 ffff88003f203f10 ffffffff810a3cc7 ffff880032627000
Call Trace:
<IRQ>
[<ffffffff8130e718>] dump_stack+0x4d/0x65
[<ffffffff810a3960>] __report_bad_irq+0x30/0xc0
[<ffffffff810a3cc7>] note_interrupt+0x227/0x270
[<ffffffff810a1380>] handle_irq_event_percpu+0x40/0x50
[<ffffffff810a13b7>] handle_irq_event+0x27/0x50
[<ffffffff810a42d5>] handle_fasteoi_irq+0x85/0x150
[<ffffffff8101d7fe>] handle_irq+0x6e/0x120
[<ffffffff8105b8bc>] ? _local_bh_enable+0x1c/0x50
[<ffffffff8101d0d6>] do_IRQ+0x46/0xd0
[<ffffffff818cef3f>] common_interrupt+0x7f/0x7f
<EOI>
[<ffffffff818cdead>] ? mwait_idle+0x7d/0x140
[<ffffffff81024c9a>] arch_cpu_idle+0xa/0x10
[<ffffffff818ce150>] default_idle_call+0x20/0x30
[<ffffffff810908fd>] cpu_startup_entry+0x16d/0x1d0
[<ffffffff818c882d>] rest_init+0x6d/0x70
[<ffffffff81f93e8f>] start_kernel+0x3e2/0x3ef
[<ffffffff81f9343d>] x86_64_start_reservations+0x38/0x3a
[<ffffffff81f93529>] x86_64_start_kernel+0xea/0xed
handlers:
[<ffffffff81411670>] serial8250_interrupt
Disabling IRQ #54
Fix this by handling interrupt only in one place.
The issue is discussed here: https://github.com/andy-shev/linux/issues/5
Moreover this also fixes another bug when Rx DMA returns wrong residue and we
can't rely on it.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ste_dma40 has burst level granularity on the residue
registers, which is necessary for some clients to know,
notably the UART. Before this patch we get this message:
uart-pl011 80007000.uart: RX DMA disabled - no residue processing
This patch fixes it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since the introduction of the .directions flags, ste_dma40 was
never patched to indicate which transfer directions it can manage.
This causes a problem when trying to use the dmaengine for generic
ALSA SoC DMA:
ux500-msp-i2s.1: Failed to get DMA channel capabilities, falling
back to period counting: -6
This patch fixes this issue by indicating the supported transfer
directions for slave and memcpy channels.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The slave mapping should be removed together with other channel
resources when the channel is freed. If it's not unmapped it will hang
around forever after the channel is freed.
Fixes: 9f878603db ("dmaengine: rcar-dmac: add iommu support for slave transfers")
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We do not yet have users of port_window. The following errors were found
when converting the tusb6010_omap.c musb driver:
- The peripheral side must have SRC_/DST_PACKED disabled
- when configuring the burst for the peripheral side the memory side
configuration were overwritten: d->csdp = ... -> d->csdp |= ...
- The EI and FI were configured for the wrong sides of the transfers.
With these changes and the converted tus6010_omap.c I was able to verify
that things are working as they expected to work.
Fixes: 201ac4861c ("dmaengine: omap-dma: Support for slave devices with data port window")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds some error messages when a slave device fails to request a
channel.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Reviewed-by: Ludovic BARRE <ludovic.barre@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
On a kernel with DEBUG_LOCKS, ioat_free_chan_resources triggers an
in_interrupt() warning. With PROVE_LOCKING, it reports detecting a
SOFTIRQ-safe to SOFTIRQ-unsafe lock ordering in the same code path.
This is because dma_generic_alloc_coherent() checks if the GFP flags
permit blocking. It allocates from different subsystems if blocking is
permitted. The free path knows how to return the memory to the correct
allocator. If GFP_KERNEL is specified then the alloc and free end up
going through cma_alloc(), which uses mutexes.
Given that ioat_free_chan_resources() can be called in interrupt
context, ioat_alloc_chan_resources() must specify GFP_NOWAIT so that the
allocations do not block and instead use an allocator that uses
spinlocks.
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
LPE Audio driver should take care of DMA IPs by itself. Keeping an ID like this
in dw_dma_pci.c is anyway wrong since that block has two DMA controllers under
one ID (like MFD device).
That's also why I didn't include LPE Audio ID for Intel Merrifield previously.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch sets the max_burst value supported by the STM32 DMA
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Implement the new device_synchronize() callback to allow proper
synchronization when stopping a channel.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch resolves the residue computation issue detected in cyclic mode.
Now, in cyclic mode, we increment next_sg variable as soon as a period is
transferred instead of after pushing a new sg request.
Then, we take into account that after transferring a complete buffer,
the next_sg variable is equal to 0.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Reviewed-by: Ludovic BARRE <ludovic.barre@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch reworks the way to manage transfer starting.
Now, starting DMA is only allowed when the channel is not busy.
Then, stm32_dma_start_transfer is declared as void.
At least, after each transfer completion, we start the next transfer if a
new descriptor as been queued in the issued list during an ongoing
transfer.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Reviewed-by: Ludovic BARRE <ludovic.barre@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As STM32 DMA driver is only used as buit-in driver, it couldn't be used as
module.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Reviewed-by: Ludovic BARRE <ludovic.barre@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
PL330 DMA engine driver is leaking a runtime reference after any terminated
DMA transactions. This patch fixes this issue by tracking runtime PM state
of the device and making additional call to pm_runtime_put() in terminate_all
callback if needed.
Fixes: ae43b32891 ("ARM: 8202/1: dmaengine: pl330: Add runtime Power Management support v12")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The original patch did not done what it was supposed to be doing and even
worst it broke legacy boot (OMAP1).
The lch_map size should be the number of available logical channels in sDMA
and the od->dma_requests should store the number of available DMA request
lines usable in sDMA.
In legacy mode we do not have a way to get the DMA request count, in that
case we use OMAP_SDMA_REQUESTS (127), despite the fact that OMAP1510 have
only 31 DMA request line.
Fixes: 2d1a9a946f ("dmaengine: omap-dma: Dynamically allocate memory for lch_map")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: stable@vger.kernel.org # v4.9
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The dma residue is defined as the free space to end of transfer buffer,
which could be multiple segments chained together. So the residue
calculation in zx_dma_tx_status() works for both slave_sg and cyclic
case. But unfortunately, the 'index' is wrong. It should plus one,
because the current segment is already occupied and shouldn't be counted
into free space.
This fixes the HDMI audio noise issue we see on ZX296718 with SPDIF
interface.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The zx_dma driver supports cyclic transfer mode. Let's set DMA_CYCLIC
cap_mask bit to make that clear, and avoid unnecessary failure when
clients request channel via dma_request_chan_by_mask() with DMA_CYCLIC
bit set in mask.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
ZTE ZX dma driver is not ZX296702 specific. It works for not only
ZX296702 but also other ZTE ZX family platforms like ZX296718. Let's
rename the file to reflect that.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 3d8cc00073 ("dmaengine: ipu: Consolidate duplicated irq handlers")
consolidated the two interrupts routines into one, but the remaining
interrupt routine only checks the status of the error interrupts, not the
normal interrupts.
This patch fixes that problem (tested on i.MX31 PDK board).
Fixes: 3d8cc00073 ("dmaengine: ipu: Consolidate duplicated irq handlers")
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: <stable@vger.kernel.org> # 4.1.x
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dmaengine currently uses an IDR to allocate DMA IDs, but it only needs
to know whether IDs are in use or not; the ID to pointer functionality
of the IDR is unused. That means it can use the more space-efficient IDA.
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
chan->desc is always set to NULL when a DMA transfer is complete.
As a DMA transfer could be complete during the call of stm32_dma_tx_status,
we need to be sure that chan->desc is not NULL before using this variable
to avoid a null pointer deference issue.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Reviewed-by: Ludovic BARRE <ludovic.barre@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch sets the right number of arguments to be used for DMA clients
which request channels from DT.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Reviewed-by: Ludovic BARRE <ludovic.barre@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The Skylake ioatdma is technically CBDMA 3.2+ and contains the same hardware
bits with some additional 3.3 features, but it's not really 3.3 where the
driver is concerned.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Adding Skylake Xeon PCI device ids for ioatdma and related bits.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Fairly routine update this time around with all changes specific to drivers.
o New driver for STMicroelectronics FDMA
o Memory-to-memory transfers on dw dmac
o Support for slave maps on pl08x devices
o Bunch of driver fixes to use dma_pool_zalloc
o Bunch of compile and warning fixes spread across drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Pf0d
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.10-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"Fairly routine update this time around with all changes specific to
drivers:
- New driver for STMicroelectronics FDMA
- Memory-to-memory transfers on dw dmac
- Support for slave maps on pl08x devices
- Bunch of driver fixes to use dma_pool_zalloc
- Bunch of compile and warning fixes spread across drivers"
[ The ST FDMA driver already came in earlier through the remoteproc tree ]
* tag 'dmaengine-4.10-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (68 commits)
dmaengine: sirf-dma: remove unused ‘sdesc’
dmaengine: pl330: remove unused ‘regs’
dmaengine: s3c24xx: remove unused ‘cdata’
dmaengine: stm32-dma: remove unused ‘src_addr’
dmaengine: stm32-dma: remove unused ‘dst_addr’
dmaengine: stm32-dma: remove unused ‘sfcr’
dmaengine: pch_dma: remove unused ‘cookie’
dmaengine: mic_x100_dma: remove unused ‘data’
dmaengine: img-mdc: remove unused ‘prev_phys’
dmaengine: usb-dmac: remove unused ‘uchan’
dmaengine: ioat: remove unused ‘res’
dmaengine: ioat: remove unused ‘ioat_dma’
dmaengine: ioat: remove unused ‘is_raid_device’
dmaengine: pl330: do not generate unaligned access
dmaengine: k3dma: move to dma_pool_zalloc
dmaengine: at_hdmac: move to dma_pool_zalloc
dmaengine: at_xdmac: don't restore unsaved status
dmaengine: ioat: set error code on failures
dmaengine: ioat: set error code on failures
dmaengine: DW DMAC: add multi-block property to device tree
...
Introduces remoteproc "subdevice" support, which allows remoteproc
driver to associate devices to the "running" state of the remoteproc,
allowing devices to be probed and removed as the remote processor is
booted, shut down or recovering from a crash.
Handling of virtio device resources was improved, vring memory is now
allocated as part of other memory allocation. This ensures that all
vrings for all virtio devices are allocated before we boot the remote
processor.
The debugfs mechanism for starting and stopping remoteproc instances was
replaced with a sysfs interface, also providing a mechanism for
specifying firmware to use by the instance. This allows user space to
load and boot use case specific firmware on remote processors.
New drivers for the ST Slimcore and Qualcomm Hexagon DSP as well as
removal of the unused StE modem loader.
Finally support for crash recovery in the Qualcomm Wirelss subsystem
(used for WiFi/BT/FM on a number of platforms) and a number of bug fixes
and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/1kU
-----END PGP SIGNATURE-----
Merge tag 'rproc-v4.10' of git://github.com/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
- introduce remoteproc "subdevice" support, which allows remoteproc
driver to associate devices to the "running" state of the remoteproc,
allowing devices to be probed and removed as the remote processor is
booted, shut down or recovering from a crash.
- handling of virtio device resources was improved, vring memory is now
allocated as part of other memory allocation. This ensures that all
vrings for all virtio devices are allocated before we boot the remote
processor.
- the debugfs mechanism for starting and stopping remoteproc instances
was replaced with a sysfs interface, also providing a mechanism for
specifying firmware to use by the instance. This allows user space to
load and boot use case specific firmware on remote processors.
- new drivers for the ST Slimcore and Qualcomm Hexagon DSP as well as
removal of the unused StE modem loader.
- finally support for crash recovery in the Qualcomm Wirelss subsystem
(used for WiFi/BT/FM on a number of platforms) and a number of bug
fixes and cleanups
* tag 'rproc-v4.10' of git://github.com/andersson/remoteproc: (49 commits)
remoteproc: qcom_adsp_pil: select qcom_scm
remoteproc: Drop wait in __rproc_boot()
remoteproc/ste: Delete unused driver
remoteproc: Remove "experimental" warning
remoteproc: qcom_adsp_pil: select qcom_scm
dt-binding: soc: qcom: smd: Add label property
remoteproc: qcom: mdt_loader: add include for sizes
remoteproc: Update last rproc_put users to rproc_free
remoteproc: qcom: adsp: Add missing MODULE_DEVICE_TABLE
remoteproc: wcnss-pil: add QCOM_SMD dependency
dmaengine: st_fdma: Revert: "Revert: Update st_fdma to 'depends on REMOTEPROC'"
remoteproc: Add support for xo clock
remoteproc: adsp-pil: fix recursive dependency
remoteproc: Introduce Qualcomm ADSP PIL
dt-binding: remoteproc: Introduce ADSP loader binding
remoteproc: qcom_wcnss: Fix circular module dependency
remoteproc: Merge table_ptr and cached_table pointers
remoteproc: Remove custom vdev handler list
remoteproc: Update max_notifyid as we allocate vrings
remoteproc: Decouple vdev resources and devices
...
Pull x86 idle updates from Ingo Molnar:
"There were two bigger changes in this development cycle:
- remove idle notifiers:
32 files changed, 74 insertions(+), 803 deletions(-)
These notifiers were of questionable value and the main usecase,
the i7300 driver, was essentially unmaintained and can be removed,
plus modern power management concepts don't need the callback - so
use this golden opportunity and get rid of this opaque and fragile
callback from a latency sensitive code path.
(Len Brown, Thomas Gleixner)
- improve the AMD Erratum 400 workaround that used high overhead MSR
polling in the idle loop (Borisla Petkov, Thomas Gleixner)"
* 'x86-idle-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Remove empty idle.h header
x86/amd: Simplify AMD E400 aware idle routine
x86/amd: Check for the C1E bug post ACPI subsystem init
x86/bugs: Separate AMD E400 erratum and C1E bug
x86/cpufeature: Provide helper to set bugs bits
x86/idle: Remove enter_idle(), exit_idle()
x86: Remove x86_test_and_clear_bit_percpu()
x86/idle: Remove is_idle flag
x86/idle: Remove idle_notifier
i7300_idle: Remove this driver
In sirfsoc_dma_pm_suspend(), variable ‘sdesc’ is initialized but never used, which
leads to warning with W=1.
drivers/dma/sirf-dma.c: In function 'sirfsoc_dma_pm_suspend':
drivers/dma/sirf-dma.c:1014:27: warning: variable 'sdesc' set but not used [-Wunused-but-set-variable]
So remove it.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In pl330_add(), variable ‘regs’ is initialized but never used, which
leads to warning with W=1.
drivers/dma/pl330.c: In function 'pl330_add':
drivers/dma/pl330.c:1891:16: warning: variable 'regs' set but not used [-Wunused-but-set-variable]
So remove it.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In s3c24xx_dma_get_phy(), variable ‘cdata’ is initialized but never used, which
leads to warning with W=1. Removing this make pdata unused.
drivers/dma/s3c24xx-dma.c: In function ‘s3c24xx_dma_get_phy’:
drivers/dma/s3c24xx-dma.c:293:30: warning: variable ‘cdata’ set but not used [-Wunused-but-set-variable]
struct s3c24xx_dma_channel *cdata;
So remove both of them.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In stm32_dma_set_xfer_param(), variable ‘src_addr’ is initialized but never used, which
leads to warning with W=1
drivers/dma/stm32-dma.c: In function ‘stm32_dma_set_xfer_param’:
drivers/dma/stm32-dma.c:577:13: warning: variable ‘src_addr’ set but not used [-Wunused-but-set-variable]
dma_addr_t src_addr, dst_addr;
So remove it.
Reviewed-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In stm32_dma_set_xfer_param(), variable ‘dst_addr’ is initialized but never used, which
leads to warning with W=1
drivers/dma/stm32-dma.c: In function ‘stm32_dma_set_xfer_param’:
drivers/dma/stm32-dma.c:577:23: warning: variable ‘dst_addr’ set but not used [-Wunused-but-set-variable]
dma_addr_t src_addr, dst_addr;
So remove it.
Reviewed-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In stm32_dma_chan_irq(), variable ‘sfcr’ is initialized but never used, which
leads to warning with W=1
drivers/dma/stm32-dma.c: In function ‘stm32_dma_chan_irq’:
drivers/dma/stm32-dma.c:530:19: warning: variable ‘sfcr’ set but not used [-Wunused-but-set-variable]
u32 status, scr, sfcr;
So remove it.
Reviewed-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In pd_tx_submit(), variable ‘cookie’ is initialized but never used, which
leads to warning with W=1
drivers/dma/pch_dma.c: In function ‘pd_tx_submit’:
drivers/dma/pch_dma.c:420:15: warning: variable ‘cookie’ set but not used [-Wunused-but-set-variable]
dma_cookie_t cookie;
So remove it.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In mic_dma_init(), variable ‘data’ is initialized but never used, which
leads to warning with W=1
drivers/dma/mic_x100_dma.c: In function ‘mic_dma_init’:
drivers/dma/mic_x100_dma.c:557:17: warning: variable ‘data’ set but not used [-Wunused-but-set-variable]
unsigned long data;
So remove it.
Cc: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In mdc_prep_dma_memcpy(), mdc_prep_dma_cyclic() and mdc_prep_slave_sg()
variable ‘prev_phys’ is initialized but never used, which
leads to warning with W=1
drivers/dma/img-mdc-dma.c: In function ‘mdc_prep_dma_memcpy’:
drivers/dma/img-mdc-dma.c:295:24: warning: variable ‘prev_phys’ set but not used [-Wunused-but-set-variable]
dma_addr_t curr_phys, prev_phys;
drivers/dma/img-mdc-dma.c: In function ‘mdc_prep_dma_cyclic’:
drivers/dma/img-mdc-dma.c:378:24: warning: variable ‘prev_phys’ set but not used [-Wunused-but-set-variable]
dma_addr_t curr_phys, prev_phys;
drivers/dma/img-mdc-dma.c: In function ‘mdc_prep_slave_sg’:
drivers/dma/img-mdc-dma.c:461:24: warning: variable ‘prev_phys’ set but not
used [-Wunused-but-set-variable]
dma_addr_t curr_phys, prev_phys;
So remove it.
Cc: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In usb_dmac_of_xlate(), variable ‘uchan’ is initialized but never used, which
leads to warning with W=1
drivers/dma/sh/usb-dmac.c: In function ‘usb_dmac_of_xlate’:
drivers/dma/sh/usb-dmac.c:655:24: warning: variable ‘uchan’ set but not used [-Wunused-but-set-variable]
struct usb_dmac_chan *uchan;
So remove it.
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In __cleanup(), variable ‘res’ is initialized but never used, which
leads to warning with W=1
drivers/dma/ioat/dma.c: In function ‘__cleanup’:
drivers/dma/ioat/dma.c:614:28: warning: variable ‘res’ set but not used [-Wunused-but-set-variable]
struct dmaengine_result res;
So remove it.
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In ioat_tx_submit_unlock(), variable ‘ioat_dma’ is initialized but never
used, which leads to warning with W=1
drivers/dma/ioat/dma.c: In function ‘ioat_alloc_ring_ent’:
drivers/dma/ioat/dma.c:341:25: warning: variable ‘ioat_dma’ set but not used [-Wunused-but-set-variable]
struct ioatdma_device *ioat_dma;
So remove it.
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In ioat3_dma_probe(), variable ‘is_raid_device’ is initialized but never
used, which leads to warning with W=1
drivers/dma/ioat/init.c: In function ‘ioat3_dma_probe’:
drivers/dma/ioat/init.c:1084:7: warning: variable ‘is_raid_device’ set
but not used [-Wunused-but-set-variable]
bool is_raid_device = false;
So remove it.
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
save_gs is supposed to save the channel status in order to be restored at
resume time but it is never updated and is always 0. Anyway, the channel
status is updated in the per channel loop later in the resume function.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In function ioat_xor_val_self_test(), when the calls to
dma_mapping_error() fail, the value of return variable err is 0
(indicates no error). As a result, the return value may be inconsistent
with the execution status. This patch fixes the bug by assigning
"-ENOMEM" to err on the error path.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188601
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In function ioat_dma_self_test(), when the calls to dma_mapping_error()
fails, the value of return variable err is 0 (indicates no error). As a
result, the return value may be inconsistent with the execution status.
This patch fixes the bug by assigning -ENOMEM to err on the error path.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188591
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Several versions of DW DMAC have multi block transfers hardware
support. Hardware support of multi block transfers is disabled
by default if we use DT to configure DMAC and software emulation
of multi block transfers used instead.
Add multi-block property, so it is possible to enable hardware
multi block transfers (if present) via DT.
Switch from per device is_nollp variable to multi_block array
to be able enable/disable multi block transfers separately per
channel.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
All known devices, which use DT for configuration, support
memory-to-memory transfers. So enable it by default, if we read
configuration from DT.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The last param set in a transfer should always be pointing to dummy
param set in non-cyclic mode. When system wakes from low power state
EDMA PARAM slots may be reset to random values. Hence, re-initialize
dummy slot to dummy param set on system resume.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Based on the src/dst_port_window_size - if it is set - configure the DMA
channel to use double indexing in order to be able to loop within the
address window.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We should use dma_pool_zalloc instead of dma_pool_alloc/memset.
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We should use dma_pool_zalloc instead of dma_pool_alloc/memset.
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Existing implementation does not honor the alignment restrictions imposed
by the DMA engines. Allocate buffers with built in slack for honoring
alignment restrictions. Creating new arrays to hold the aligned pointers
and use those pointers for operations.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Inside pdc_alloc_desc(), pci_pool_alloc() followed by memset will be
replaced by pci_pool_zalloc()
Signed-off-by: Souptick joarder <jrdr.linux@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_pool_alloc does not initialize the value of the newly allocated
block for the v_lli, and the uninitilize value make the tests failed
which is on pine64 with dmatest.
we can fix it just change the "|=" to "=" for the v_lli->cfg.
Signed-off-by: Hao Zhang <hao5781286@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Niklas Söderlund