With bus-type/bus-width properties in the endpoint nodes, the video-
interface of the connection can be specified for cases where the
heuristic fails to select the correct output mode. This can happen
e.g. if not all RGB pins are routed on the PCB; the driver has no
way of knowing this, and needs to be told explicitly.
This is critical for the devices that have the "conflicting output
formats" issue (SAM9N12, SAM9X5, SAMA5D3), since the most significant
RGB bits move around depending on the selected output mode. For
devices that do not have the "conflicting output formats" issue
(SAMA5D2, SAMA5D4), this is completely irrelevant.
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180825085620.10566-3-peda@axentia.se
Start list of actual chips compatible with "lvds-encoder".
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180825085620.10566-2-peda@axentia.se
Pull irq update from Thomas Gleixner:
"A small set of updats/fixes for the irq subsystem:
- Allow GICv3 interrupts to be configured as wake-up sources to
enable wakeup from suspend
- Make the error handling of the STM32 irqchip init function work
- A set of small cleanups and improvements"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Allow interrupt to be configured as wake-up sources
irqchip/tango: Set irq handler and data in one go
dt-bindings: irqchip: renesas-irqc: Document r8a774a1 support
irqchip/s3c24xx: Remove unneeded comparison of unsigned long to 0
irqchip/stm32: Fix init error handling
irqchip/bcm7038-l1: Hide cpu offline callback when building for !SMP
A couple of late-merged changes that would be useful to get in this
merge window:
- Driver support for reset of audio complex on Meson platforms. The
audio driver went in this merge window, and these changes have been
in -next for a while (just not in our tree).
- Power management fixes for IOMMU on Rockchip platforms, getting
closer to kexec working on them, including Chromebooks.
- Another pass updating "arm,psci" -> "psci" for some properties that
have snuck in since last time it was done.
-----BEGIN PGP SIGNATURE-----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=dQaG
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late updates from Olof Johansson:
"A couple of late-merged changes that would be useful to get in this
merge window:
- Driver support for reset of audio complex on Meson platforms. The
audio driver went in this merge window, and these changes have been
in -next for a while (just not in our tree).
- Power management fixes for IOMMU on Rockchip platforms, getting
closer to kexec working on them, including Chromebooks.
- Another pass updating "arm,psci" -> "psci" for some properties that
have snuck in since last time it was done"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
iommu/rockchip: Move irq request past pm_runtime_enable
iommu/rockchip: Handle errors returned from PM framework
arm64: rockchip: Force CONFIG_PM on Rockchip systems
ARM: rockchip: Force CONFIG_PM on Rockchip systems
arm64: dts: Fix various entry-method properties to reflect documentation
reset: imx7: Fix always writing bits as 0
reset: meson: add meson audio arb driver
reset: meson: add dt-bindings for meson-axg audio arb
Pull libata updates from Tejun Heo:
"Nothing too interesting. Mostly ahci and ahci_platform changes, many
around power management"
* 'for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
ata: ahci_platform: enable to get and control reset
ata: libahci_platform: add reset control support
ata: add an extra argument to ahci_platform_get_resources()
ata: sata_rcar: Add r8a77965 support
ata: sata_rcar: exclude setting of PHY registers in Gen3
ata: sata_rcar: really mask all interrupts on Gen2 and later
Revert "ata: ahci_platform: allow disabling of hotplug to save power"
ata: libahci: Allow reconfigure of DEVSLP register
ata: libahci: Correct setting of DEVSLP register
ata: ahci: Enable DEVSLP by default on x86 with SLP_S0
ata: ahci: Support state with min power but Partial low power state
Revert "ata: ahci_platform: convert kcalloc to devm_kcalloc"
ata: sata_rcar: Add rudimentary Runtime PM support
ata: sata_rcar: Provide a short-hand for &pdev->dev
ata: Only output sg element mapped number in verbose debug
ata: Guard ata_scsi_dump_cdb() by ATA_VERBOSE_DEBUG
ata: ahci_platform: convert kcalloc to devm_kcalloc
ata: ahci_platform: convert kzallloc to kcalloc
ata: ahci_platform: correct parameter documentation for ahci_platform_shutdown
libata: remove ata_sff_data_xfer_noirq()
...
Including:
- PASID table handling updates for the Intel VT-d driver. It
implements a global PASID space now so that applications
usings multiple devices will just have one PASID.
- A new config option to make iommu passthroug mode the default.
- New sysfs attribute for iommu groups to export the type of the
default domain.
- A debugfs interface (for debug only) usable by IOMMU drivers
to export internals to user-space.
- R-Car Gen3 SoCs support for the ipmmu-vmsa driver
- The ARM-SMMU now aborts transactions from unknown devices and
devices not attached to any domain.
- Various cleanups and smaller fixes all over the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=TeYQ
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- PASID table handling updates for the Intel VT-d driver. It implements
a global PASID space now so that applications usings multiple devices
will just have one PASID.
- A new config option to make iommu passthroug mode the default.
- New sysfs attribute for iommu groups to export the type of the
default domain.
- A debugfs interface (for debug only) usable by IOMMU drivers to
export internals to user-space.
- R-Car Gen3 SoCs support for the ipmmu-vmsa driver
- The ARM-SMMU now aborts transactions from unknown devices and devices
not attached to any domain.
- Various cleanups and smaller fixes all over the place.
* tag 'iommu-updates-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (42 commits)
iommu/omap: Fix cache flushes on L2 table entries
iommu: Remove the ->map_sg indirection
iommu/arm-smmu-v3: Abort all transactions if SMMU is enabled in kdump kernel
iommu/arm-smmu-v3: Prevent any devices access to memory without registration
iommu/ipmmu-vmsa: Don't register as BUS IOMMU if machine doesn't have IPMMU-VMSA
iommu/ipmmu-vmsa: Clarify supported platforms
iommu/ipmmu-vmsa: Fix allocation in atomic context
iommu: Add config option to set passthrough as default
iommu: Add sysfs attribyte for domain type
iommu/arm-smmu-v3: sync the OVACKFLG to PRIQ consumer register
iommu/arm-smmu: Error out only if not enough context interrupts
iommu/io-pgtable-arm-v7s: Abort allocation when table address overflows the PTE
iommu/io-pgtable-arm: Fix pgtable allocation in selftest
iommu/vt-d: Remove the obsolete per iommu pasid tables
iommu/vt-d: Apply per pci device pasid table in SVA
iommu/vt-d: Allocate and free pasid table
iommu/vt-d: Per PCI device pasid table interfaces
iommu/vt-d: Add for_each_device_domain() helper
iommu/vt-d: Move device_domain_info to header
iommu/vt-d: Apply global PASID in SVA
...
Pull thermal management updates from Zhang Rui:
- Add Daniel Lezcano as the reviewer of thermal framework and SoC
driver changes (Daniel Lezcano).
- Fix a bug in intel_dts_soc_thermal driver, which does not translate
IO-APIC GSI (Global System Interrupt) into Linux irq number (Hans de
Goede).
- For device tree bindings, allow cooling devices sharing same trip
point with same contribution value to share cooling map (Viresh
Kumar).
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
dt-bindings: thermal: Allow multiple devices to share cooling map
MAINTAINERS: Add Daniel Lezcano as designated reviewer for thermal
Thermal: Intel SoC DTS: Translate IO-APIC GSI number to linux irq number
The idle-states binding documentation[1] mentions that the
'entry-method' property is required on 64-bit platforms and must be
set to "psci".
commit a13f18f59d ("Documentation: arm: Fix typo in the idle-states
bindings examples") attempted to fix this earlier but clearly more is
needed.
Fix the cpu-capacity.txt documentation that uses the incorrect value so
we don't get copy-paste errors like these. Clarify the language in
idle-states.txt by removing the reference to the psci bindings that
might be causing this confusion.
Finally, fix devicetrees of various boards to reflect current
documentation.
[1] Documentation/devicetree/bindings/arm/idle-states.txt (see
idle-states node)
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds a single new driver for the Amlogic Meson Audio Memory Arbiter
resets.
-----BEGIN PGP SIGNATURE-----
iI0EABYIADUWIQRRO6F6WdpH1R0vGibVhaclGDdiwAUCW2RYpxcccC56YWJlbEBw
ZW5ndXRyb25peC5kZQAKCRDVhaclGDdiwGdpAQDW1fXG6l0a/YjTUlmuia8LAHxS
4h0sJCUCEyNSEaTKAQEA0Cunr8w9D0kQlj7XjZyGylRX2wSIRI9rMseTm4U68wg=
=xBwp
-----END PGP SIGNATURE-----
Merge tag 'reset-for-4.19-2' of git://git.pengutronix.de/git/pza/linux into next/late
Reset controller changes for v4.19, part 2
This adds a single new driver for the Amlogic Meson Audio Memory Arbiter
resets.
* tag 'reset-for-4.19-2' of git://git.pengutronix.de/git/pza/linux:
reset: meson: add meson audio arb driver
reset: meson: add dt-bindings for meson-axg audio arb
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge yet more updates from Andrew Morton:
- the rest of MM
- various misc fixes and tweaks
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
mm: Change return type int to vm_fault_t for fault handlers
lib/fonts: convert comments to utf-8
s390: ebcdic: convert comments to UTF-8
treewide: convert ISO_8859-1 text comments to utf-8
drivers/gpu/drm/gma500/: change return type to vm_fault_t
docs/core-api: mm-api: add section about GFP flags
docs/mm: make GFP flags descriptions usable as kernel-doc
docs/core-api: split memory management API to a separate file
docs/core-api: move *{str,mem}dup* to "String Manipulation"
docs/core-api: kill trailing whitespace in kernel-api.rst
mm/util: add kernel-doc for kvfree
mm/util: make strndup_user description a kernel-doc comment
fs/proc/vmcore.c: hide vmcoredd_mmap_dumps() for nommu builds
treewide: correct "differenciate" and "instanciate" typos
fs/afs: use new return type vm_fault_t
drivers/hwtracing/intel_th/msu.c: change return type to vm_fault_t
mm: soft-offline: close the race against page allocation
mm: fix race on soft-offlining free huge pages
namei: allow restricted O_CREAT of FIFOs and regular files
hfs: prevent crash on exit from failed search
...
Almost all files in the kernel are either plain text or UTF-8 encoded. A
couple however are ISO_8859-1, usually just a few characters in a C
comments, for historic reasons.
This converts them all to UTF-8 for consistency.
Link: http://lkml.kernel.org/r/20180724111600.4158975-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Simon Horman <horms@verge.net.au> [IPVS portion]
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> [IIO]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Acked-by: Rob Herring <robh@kernel.org>
Cc: Joe Perches <joe@perches.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Also add these typos to spelling.txt so checkpatch.pl will look for them.
Link: http://lkml.kernel.org/r/88af06b9de34d870cb0afc46cfd24e0458be2575.1529471371.git.fthain@telegraphics.com.au
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This contains mostly minor bug fixes as well as some new chip support
for existing drivers.
-----BEGIN PGP SIGNATURE-----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=Y0ng
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This contains mostly minor bug fixes as well as some new chip support
for existing drivers"
* tag 'pwm/for-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: mediatek: Add MT7628 support
dt-bindings: pwm: Add MT7628 information
dt-bindings: pwm: rcar: Add bindings for R-Car E3 support
pwm: meson: Fix mux clock names
pwm: stm32-lp: Remove useless loop in stm32_pwm_lp_remove()
pwm: omap-dmtimer: Return -EPROBE_DEFER if no dmtimer platform data
pwm: mxs: Switch to SPDX identifier
dt-bindings: pwm: fsl-ftm: Add compatible string for i.MX8QM
pwm: fsl-ftm: Enable support for the new SoC i.MX8QM
pwm: fsl-ftm: Added the support of per-compatible data
pwm: fsl-ftm: Added a dedicated IP interface clock
pwm: cros-ec: Switch to SPDX identifier
pwm: imx: Switch to SPDX identifier
pwm: tiehrpwm: Fix disabling of output of PWMs
pwm: tiehrpwm: Don't use emulation mode bits to control PWM output
pwm: berlin: Don't use broken prescaler values
- add support for deferred console takeover, when enabled defers
fbcon taking over the console from the dummy console until the
first text is displayed on the console - together with the "quiet"
kernel commandline option this allows fbcon to still be used
together with a smooth graphical bootup (Hans de Goede)
- improve console locking debugging code (Thomas Zimmermann)
- copy the ACPI BGRT boot graphics to the framebuffer when deferred
console takeover support is used in efifb driver (Hans de Goede)
- update udlfb driver - fix lost console when the user unplugs a USB
adapter, fix the screen corruption issue, fix locking and add some
performance optimizations (Mikulas Patocka)
- update pxafb driver - fix using uninitialized memory, switch to
devm_* API, handle initialization errors and add support for
lcd-supply regulator (Daniel Mack)
- add support for boards booted with a DeviceTree in pxa3xx_gcu
driver (Daniel Mack)
- rename omap2 module to omap2fb.ko to avoid conflicts with omap1
driver (Arnd Bergmann)
- enable ACPI-based enumeration for goldfishfb driver (Yu Ning)
- fix goldfishfb driver to make user space Android code use 60 fps
(Christoffer Dall)
- print big fat warning when nomodeset kernel parameter is used in
vgacon driver (Lyude Paul)
- remove VLA usage from fsl-diu-fb driver (Kees Cook)
- misc fixes (Julia Lawall, Geert Uytterhoeven, Fredrik Noring,
Yisheng Xie, Dan Carpenter, Daniel Vetter, Anton Vasilyev, Randy
Dunlap, Gustavo A. R. Silva, Colin Ian King, Fengguang Wu)
- misc cleanups (Roman Kiryanov, Yisheng Xie, Colin Ian King)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7UE9
-----END PGP SIGNATURE-----
Merge tag 'fbdev-v4.19' of https://github.com/bzolnier/linux
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
"Mostly small fixes and cleanups for fb drivers (the biggest updates
are for udlfb and pxafb drivers). This also adds deferred console
takeover support to the console code and efifb driver.
Summary:
- add support for deferred console takeover, when enabled defers
fbcon taking over the console from the dummy console until the
first text is displayed on the console - together with the "quiet"
kernel commandline option this allows fbcon to still be used
together with a smooth graphical bootup (Hans de Goede)
- improve console locking debugging code (Thomas Zimmermann)
- copy the ACPI BGRT boot graphics to the framebuffer when deferred
console takeover support is used in efifb driver (Hans de Goede)
- update udlfb driver - fix lost console when the user unplugs a USB
adapter, fix the screen corruption issue, fix locking and add some
performance optimizations (Mikulas Patocka)
- update pxafb driver - fix using uninitialized memory, switch to
devm_* API, handle initialization errors and add support for
lcd-supply regulator (Daniel Mack)
- add support for boards booted with a DeviceTree in pxa3xx_gcu
driver (Daniel Mack)
- rename omap2 module to omap2fb.ko to avoid conflicts with omap1
driver (Arnd Bergmann)
- enable ACPI-based enumeration for goldfishfb driver (Yu Ning)
- fix goldfishfb driver to make user space Android code use 60 fps
(Christoffer Dall)
- print big fat warning when nomodeset kernel parameter is used in
vgacon driver (Lyude Paul)
- remove VLA usage from fsl-diu-fb driver (Kees Cook)
- misc fixes (Julia Lawall, Geert Uytterhoeven, Fredrik Noring,
Yisheng Xie, Dan Carpenter, Daniel Vetter, Anton Vasilyev, Randy
Dunlap, Gustavo A. R. Silva, Colin Ian King, Fengguang Wu)
- misc cleanups (Roman Kiryanov, Yisheng Xie, Colin Ian King)"
* tag 'fbdev-v4.19' of https://github.com/bzolnier/linux: (54 commits)
Documentation/fb: corrections for fbcon.txt
fbcon: Do not takeover the console from atomic context
dummycon: Stop exporting dummycon_[un]register_output_notifier
fbcon: Only defer console takeover if the current console driver is the dummycon
fbcon: Only allow FRAMEBUFFER_CONSOLE_DEFERRED_TAKEOVER if fbdev is builtin
fbdev: omap2: omapfb: fix ifnullfree.cocci warnings
fbdev: omap2: omapfb: fix bugon.cocci warnings
fbdev: omap2: omapfb: fix boolreturn.cocci warnings
fb: amifb: fix build warnings when not builtin
fbdev/core: Disable console-lock warnings when fb.lockless_register_fb is set
console: Replace #if 0 with atomic var 'ignore_console_lock_warning'
udlfb: use spin_lock_irq instead of spin_lock_irqsave
udlfb: avoid prefetch
udlfb: optimization - test the backing buffer
udlfb: allow reallocating the framebuffer
udlfb: set line_length in dlfb_ops_set_par
udlfb: handle allocation failure
udlfb: set optimal write delay
udlfb: make a local copy of fb_ops
udlfb: don't switch if we are switching to the same videomode
...
Business as usual -- the bulk of our changes are to devicetree files
with new hardware support, new SoCs and platforms, and new board types.
New SoCs/platforms:
- Raspberry Pi Compute Module (CM1) and IO board
- i.MX6SSL from NXP
- Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN and
PLC interfaces
- TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
controllers, communication and PRU subsystem and lots of other
interfaces (PCIe, USB3, etc).
New boards and systems:
- Several Atmel at91-based boards from Laird
- Marvell Armada388-based Helios4 board from SolidRun
- Samsung Aires-based phones (s5pv210)
- Allwinner A64-based Pinebook laptop
In addition to the above, there's the usual amount of new devices
described on existing platforms, fixes and tweaks and new minor variants
of boards/platforms.
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAlt+NecPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3ScQQAIic6NPWiqGEwTRN1I+WoyoCt8oTGgiiu1kf
h23RaLWI+TaEpR1yg5ko6wGlxlvBG1C/u2sOc0lD9nSt9JQ3evXXwMQ0bUNhKdSE
8z3jhpnJYu5iNDsB15XfznhivpjOQUQNQXPR1/PG9j6SCKgdWi6wYR+A+q98Pe9d
otzMizQOY0QUMYAec20Zvzgfs+AvEtOAo/w5K4tRb+Fv/EVixV8bVeT4uykxunFt
6xOM0Ssvnwo3AnEh+V+FjAL8khMC7A3JC+/emXqqcw1Ogdg/GSnxriL7v6LchcwH
fvYb8hujQCcZ0+mlN0W214RkWd1xAc0CwJ0JdKw/RMnskty5u5B7gXcDyZFw1oJ7
b7Uof7N8l12lsXTqWW8CKOHupI1gxYshi0QJzkgkfY6P3h8ntE8HJhhcgjcHE0AN
3mMjhzbDGjfUykVgS2rFpR6tm3JHT13jDl88jhAT+xtuYYxy60nqPBM9MD6jIzjF
BnIVJBNX3sYa7aheEnZFBuA/Af/05fKbpUVQTNwnfq2f6NYDAbF9iBkCHepudZBa
0U+tNHuDlVXwLXoocE1Nac5IJgPiuX2bsuJ9xHKLXb6hMr9L4YtPOaKwDaJb1hTZ
XIHhlrF9w0ig9gu3IxaE+rC3hfu965CeFws0kwSZ9l52xmSP0Yi22ebSTfP6+h+u
XLyOhpp8
=J0qC
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Olof Johansson:
"Business as usual -- the bulk of our changes are to devicetree files
with new hardware support, new SoCs and platforms, and new board
types.
New SoCs/platforms:
- Raspberry Pi Compute Module (CM1) and IO board
- i.MX6SSL from NXP
- Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN
and PLC interfaces
- TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
controllers, communication and PRU subsystem and lots of other
interfaces (PCIe, USB3, etc).
New boards and systems:
- Several Atmel at91-based boards from Laird
- Marvell Armada388-based Helios4 board from SolidRun
- Samsung Aires-based phones (s5pv210)
- Allwinner A64-based Pinebook laptop
In addition to the above, there's the usual amount of new devices
described on existing platforms, fixes and tweaks and new minor
variants of boards/platforms"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (478 commits)
arm64: dts: sdm845: Add tsens nodes
arm64: dts: msm8996: thermal: Initialise via DT and add second controller
arm64: dts: sprd: Add one suspend timer
arm64: dts: sprd: Add SC27XX ADC device
arm64: dts: sprd: Add SC27XX eFuse device
arm64: dts: sprd: Add SC27XX vibrator device
arm64: dts: sprd: Add SC27XX breathing light controller device
arm64: dts: meson-axg: add spdif-dit codec
arm64: dts: meson-axg: add lineout codec
arm64: dts: meson-axg: add linein codec
arm64: dts: meson-axg: add tdm interfaces
arm64: dts: meson-axg: add tdmout formatters
arm64: dts: meson-axg: add tdmin formatters
arm64: dts: meson-axg: add spdifout
arm64: dts: rockchip: add led support for Firefly-RK3399
arm64: dts: rockchip: remove deprecated Type-C PHY properties on rk3399
arm64: dts: rockchip: add power button support for Firefly-RK3399
ARM: dts: aspeed: Add coprocessor interrupt controller
arm64: dts: meson-axg: add audio arb reset controller
arm64: dts: meson-axg: add usb power regulator
...
Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC
-----BEGIN PGP SIGNATURE-----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=ZjwY
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (52 commits)
drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests
soc: fsl: cleanup Kconfig menu
soc: fsl: dpio: Convert DPIO documentation to .rst
staging: fsl-mc: Remove remaining files
staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl
staging: fsl-dpaa2: eth: move generic FD defines to DPIO
soc: fsl: qe: gpio: Add qe_gpio_set_multiple
usb: host: exynos: Remove support for Exynos5440
clk: samsung: Remove support for Exynos5440
soc: sunxi: Add the A13, A23 and H3 system control compatibles
reset: uniphier: add reset control support for SPI
cpufreq: exynos: Remove support for Exynos5440
ata: ahci-platform: Remove support for Exynos5440
soc: imx6qp: Use GENPD_FLAG_ALWAYS_ON for PU errata
soc: mediatek: pwrap: add mt6351 driver for mt6797 SoCs
soc: mediatek: pwrap: add pwrap driver for mt6797 SoCs
soc: mediatek: pwrap: fix cipher init setting error
dt-bindings: pwrap: mediatek: add pwrap support for MT6797
reset: uniphier: add USB3 core reset control
dt-bindings: reset: uniphier: add USB3 core reset support
...
Add support to get and control a list of resets for the device
as optional and shared. These resets must be kept de-asserted until
the device is enabled.
This is specified as shared because some SoCs like UniPhier series
have common reset controls with all ahci controller instances.
However, according to Thierry's view,
https://www.spinics.net/lists/linux-ide/msg55357.html
some hardware-specific drivers already use their own resets,
and the common reset make a path to occur double controls of resets.
The ahci_platform_get_resources() can get and control the reset
only when the second argument includes AHCI_PLATFORM_GET_RESETS bit.
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull i2c updates from Wolfram Sang:
- the core has now a lockless variant of i2c_smbus_xfer. Some open
coded versions of this got removed in drivers. This also enables
proper SCCB support in regmap.
- locking got a more precise naming. i2c_{un}lock_adapter() had to go,
and we know use i2c_lock_bus() consistently with flags like
I2C_LOCK_ROOT_ADAPTER and I2C_LOCK_SEGMENT to avoid ambiguity.
- the gpio fault injector got a new delicate testcase
- the bus recovery procedure got fixed to handle the new testcase
correctly
- a new quirk flag for controllers not able to handle zero length
messages together with driver updates to use it
- new drivers: FSI bus attached I2C masters, GENI I2C controller, Owl
family S900
- and a good set of driver improvements and bugfixes
* 'i2c/for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (77 commits)
i2c: rcar: implement STOP and REP_START according to docs
i2c: rcar: refactor private flags
i2c: core: ACPI: Make acpi_gsb_i2c_read_bytes() check i2c_transfer return value
i2c: core: ACPI: Properly set status byte to 0 for multi-byte writes
dt-bindings: i2c: rcar: Add r8a774a1 support
dt-bindings: i2c: sh_mobile: Add r8a774a1 support
i2c: imx: Simplify stopped state tracking
i2c: imx: Fix race condition in dma read
i2c: pasemi: remove hardcoded bus numbers on smbus
i2c: designware: Add SPDX license tag
i2c: designware: Convert to use struct i2c_timings
i2c: core: Parse SDA hold time from firmware
i2c: designware-pcidrv: Mark expected switch fall-through
i2c: amd8111: Mark expected switch fall-through
i2c: sh_mobile: use core to detect 'no zero length read' quirk
i2c: xlr: use core to detect 'no zero length' quirk
i2c: rcar: use core to detect 'no zero length' quirk
i2c: stu300: use core to detect 'no zero length' quirk
i2c: pmcmsp: use core to detect 'no zero length' quirk
i2c: mxs: use core to detect 'no zero length' quirk
...
Subsystem:
- new helpers to add custom sysfs attributes
- struct rtc_task removal along with rtc_irq_register/rtc_irq_unregister
- rtc_irq_set_state and rtc_irq_set_freq are not exported anymore
Drivers:
- armada38x: reset after rtc power loss
- ds1307: now supports m41t11
- isl1208: now supports isl1219 and tamper detection
- pcf2127: internal SRAM support
-----BEGIN PGP SIGNATURE-----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=cAQ9
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"It is now possible to add custom sysfs attributes while avoiding a
possible race condition. Unused code has been removed resulting in a
nice reduction of the code base. And more drivers have been switched
to SPDX by their maintainers.
Summary:
Subsystem:
- new helpers to add custom sysfs attributes
- struct rtc_task removal along with rtc_irq_[un]register()
- rtc_irq_set_state and rtc_irq_set_freq are not exported anymore
Drivers:
- armada38x: reset after rtc power loss
- ds1307: now supports m41t11
- isl1208: now supports isl1219 and tamper detection
- pcf2127: internal SRAM support"
* tag 'rtc-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (34 commits)
rtc: ds1307: simplify hwmon config
rtc: s5m: Add SPDX license identifier
rtc: maxim: Add SPDX license identifiers
rtc: isl1219: add device tree documentation
rtc: isl1208: set ev-evienb bit from device tree
rtc: isl1208: Add "evdet" interrupt source for isl1219
rtc: isl1208: add support for isl1219 with tamper detection
rtc: sysfs: facilitate attribute add to rtc device
rtc: remove struct rtc_task
char: rtc: remove task handling
rtc: pcf85063: preserve control register value between stop and start
rtc: sh: remove unused variable rtc_dev
rtc: unexport rtc_irq_set_*
rtc: simplify rtc_irq_set_state/rtc_irq_set_freq
rtc: remove irq_task and irq_task_lock
rtc: remove rtc_irq_register/rtc_irq_unregister
rtc: sh: remove dead code
rtc: sa1100: don't set PIE frequency
rtc: ds1307: support m41t11 variant
rtc: ds1307: fix data pointer to m41t0
...
Pull HID updates from Jiri Kosina:
- touch_max detection improvements and quirk handling fixes in wacom
driver from Jason Gerecke and Ping Cheng
- Palm rejection from Dmitry Torokhov and _dial support from Benjamin
Tissoires for hid-multitouch driver
- Low voltage support for i2c-hid driver from Stephen Boyd
- Guitar-Hero support from Nicolas Adenis-Lamarre
- other assorted small fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (40 commits)
HID: intel_ish-hid: tx_buf memory leak on probe/remove
HID: intel-ish-hid: Prevent loading of driver on Mehlow
HID: cougar: Add support for the Cougar 500k Gaming Keyboard
HID: cougar: make compare_device_paths reusable
HID: intel-ish-hid: remove redundant variable num_frags
HID: multitouch: handle palm for touchscreens
HID: multitouch: touchscreens also use confidence reports
HID: multitouch: report MT_TOOL_PALM for non-confident touches
HID: microsoft: support the Surface Dial
HID: core: do not upper bound the collection stack
HID: input: enable Totem on the Dell Canvas 27
HID: multitouch: remove one copy of values
HID: multitouch: ditch mt_report_id
HID: multitouch: store a per application quirks value
HID: multitouch: Store per collection multitouch data
HID: multitouch: make sure the static list of class is not changed
input: add MT_TOOL_DIAL
HID: elan: Add support for touchpad on the Toshiba Click Mini L9W
HID: elan: Add USB-id for HP x2 10-n000nd touchpad
HID: elan: Add a flag for selecting if the touchpad has a LED
...
- Remove unused/obsolete code/comments
- New Functionality
- Allow less granular brightness specification for high-res PWMs; pwm_bl
- Align brightness {inc,dec}rements with that perceived by the human-eye; pwm_bl
- Fix-ups
- Prepare for the introduction of -Wimplicit-fall-through; adp8860_bl
- Bug Fixes
- Fix uninitialised variable; pwm_bl
-----BEGIN PGP SIGNATURE-----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=C/pI
-----END PGP SIGNATURE-----
Merge tag 'backlight-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"Core Framework:
- Remove unused/obsolete code/comments
New Functionality:
- Allow less granular brightness specification for high-res PWMs; pwm_bl
- Align brightness {inc,dec}rements with that perceived by the human-eye; pwm_bl
Fix-ups:
- Prepare for the introduction of -Wimplicit-fall-through; adp8860_bl
Bug Fixes:
- Fix uninitialised variable; pwm_bl"
* tag 'backlight-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: pwm_bl: Fix uninitialized variable
backlight: adp8860: Mark expected switch fall-through
backlight: Remove obsolete comment for ->state
dt-bindings: pwm-backlight: Move brightness-levels to optional
backlight: pwm_bl: Compute brightness of LED linearly to human eye
dt-bindings: pwm-backlight: Add a num-interpolation-steps property
backlight: pwm_bl: Linear interpolation between brightness-levels
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
- New Device Support
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
- New Functionality
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
- Fix-ups
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
- Bug Fixes
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501
-----BEGIN PGP SIGNATURE-----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=4Yj4
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
New Device Support:
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
New Functionality:
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
Fix-upsL
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
Bug Fixes:
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501"
* tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (60 commits)
mfd: madera: Add register definitions for accessory detect
mfd: sm501: Set coherent_dma_mask when creating subdevices
mfd: bd71837: Devicetree bindings for ROHM BD71837 PMIC
mfd: bd71837: Core driver for ROHM BD71837 PMIC
media: platform: cros-ec-cec: Fix dependency on MFD_CROS_EC
mfd: sec-core: Export OF module alias table
mfd: as3722: Disable auto-power-on when AC OK
mfd: axp20x: Support AXP806 in I2C mode
mfd: axp20x: Add self-working mode support for AXP806
dt-bindings: mfd: axp20x: Add "self-working" mode for AXP806
mfd: wm8994: Allow to configure CS/ADDR Pulldown from dts
mfd: wm8994: Allow to configure Speaker Mode Pullup from dts
mfd: rave-sp: Emulate CMD_GET_STATUS on device that don't support it
mfd: rave-sp: Add legacy watchdog ping command translation
mfd: rave-sp: Add legacy EEPROM access command translation
mfd: rave-sp: Initialize flow control and parity of the port
mfd: rave-sp: Fix incorrectly specified checksum type
mfd: rave-sp: Remove unused defines
mfd: hi655x: Fix regmap area declared size for hi655x
mfd: ti_am335x_tscadc: Fix struct clk memory leak
...
Document RZ/G2M (R8A774A1) I2C compatibility with the relevant driver
dt-bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enhance the MediaTek PWM binding with details about the IP found in the
MT7628 SoC.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Pull networking fixes from David Miller:
1) Fix races in IPVS, from Tan Hu.
2) Missing unbind in matchall classifier, from Hangbin Liu.
3) Missing act_ife action release, from Vlad Buslov.
4) Cure lockdep splats in ila, from Cong Wang.
5) veth queue leak on link delete, from Toshiaki Makita.
6) Disable isdn's IIOCDBGVAR ioctl, it exposes kernel addresses. From
Kees Cook.
7) RCU usage fixup in XDP, from Tariq Toukan.
8) Two TCP ULP fixes from Daniel Borkmann.
9) r8169 needs REALTEK_PHY as a Kconfig dependency, from Heiner
Kallweit.
10) Always take tcf_lock with BH disabled, otherwise we can deadlock
with rate estimator code paths. From Vlad Buslov.
11) Don't use MSI-X on RTL8106e r8169 chips, they don't resume properly.
From Jian-Hong Pan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
ip6_vti: fix creating fallback tunnel device for vti6
ip_vti: fix a null pointer deferrence when create vti fallback tunnel
r8169: don't use MSI-X on RTL8106e
net: lan743x_ptp: convert to ktime_get_clocktai_ts64
net: sched: always disable bh when taking tcf_lock
ip6_vti: simplify stats handling in vti6_xmit
bpf: fix redirect to map under tail calls
r8169: add missing Kconfig dependency
tools/bpf: fix bpf selftest test_cgroup_storage failure
bpf, sockmap: fix sock_map_ctx_update_elem race with exist/noexist
bpf, sockmap: fix map elem deletion race with smap_stop_sock
bpf, sockmap: fix leakage of smap_psock_map_entry
tcp, ulp: fix leftover icsk_ulp_ops preventing sock from reattach
tcp, ulp: add alias for all ulp modules
bpf: fix a rcu usage warning in bpf_prog_array_copy_core()
samples/bpf: all XDP samples should unload xdp/bpf prog on SIGTERM
net/xdp: Fix suspicious RCU usage warning
net/mlx5e: Delete unneeded function argument
Documentation: networking: ti-cpsw: correct cbs parameters for Eth1 100Mb
isdn: Disable IIOCDBGVAR
...
This tag contains some major improvements to the RISC-V port, including
the necessary interrupt controller and timer support to actually make it
to userspace. Support for three devices has been added:
* Support for the ISA-mandated timers on RISC-V systems.
* Support for the ISA-mandated first-level interrupt controller on
RISC-V systems, which is handled as part of our core arch code because
it's very small and tightly tied to the ISA.
* Support for SiFive's platform-level interrupt controller, which talks
to the actual devices.
In addition to these new devices, there are a handful of cleanups all
over the RISC-V tree:
* Build fixes for various configurations
* A fix to the vDSO build's makefile so it respects CFLAGS.
* The addition of __lshrti3, a libgcc derived function necessary for
some 32-bit configurations.
* !SMP && PERF_EVENTS
* Cleanups to the arch code to remove the remnants of old versions of
the drivers that were just properly submitted.
* Some dead code from the timer driver, most of which wasn't ever
even compiled.
* Cleanups of some interrupt #defines, which are now local to the
interrupt handling code.
* Fixes to ptrace(), which while not being sufficient to fully make GDB
work are at least sufficient to get simple GDB tasks to work.
* Early printk support via RISC-V's architecturally mandated SBI console
device.
* A fix to our early debug trap handler to ensure it's always aligned.
These patches have all been through a fairly extensive review process,
but as this enables a whole pile of functionality (ie, userspace) I'm
confident we'll need to submit a few more patches. The only concrete
issues I know about are the sys_riscv_flush_icache patches, but as I
managed to screw those up on Friday I figured it'd be best to let them
bake another week.
This tag boots a Fedora root filesystem on QEMU's master branch for me,
and before this morning's rebase (from 4.18-rc8 to 4.18) it booted on
the HiFive Unleashed.
Thanks to Christoph Hellwig and the other guys at WD for getting the new
drivers in shape!
-----BEGIN PGP SIGNATURE-----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=PfnC
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-4.19-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V updates from Palmer Dabbelt:
"This contains some major improvements to the RISC-V port, including
the necessary interrupt controller and timer support to actually make
it to userspace. Support for three devices has been added:
- the ISA-mandated timers on RISC-V systems.
- the ISA-mandated first-level interrupt controller on RISC-V
systems, which is handled as part of our core arch code because
it's very small and tightly tied to the ISA.
- SiFive's platform-level interrupt controller, which talks to the
actual devices.
In addition to these new devices, there are a handful of cleanups all
over the RISC-V tree:
- build fixes for various configurations:
* A fix to the vDSO build's makefile so it respects CFLAGS.
* The addition of __lshrti3, a libgcc derived function necessary
for some 32-bit configurations.
* !SMP && PERF_EVENTS
- Cleanups to the arch code to remove the remnants of old versions of
the drivers that were just properly submitted.
* Some dead code from the timer driver, most of which wasn't ever
even compiled.
* Cleanups of some interrupt #defines, which are now local to the
interrupt handling code.
- Fixes to ptrace(), which while not being sufficient to fully make
GDB work are at least sufficient to get simple GDB tasks to work.
- Early printk support via RISC-V's architecturally mandated SBI
console device.
- A fix to our early debug trap handler to ensure it's always
aligned.
These patches have all been through a fairly extensive review process,
but as this enables a whole pile of functionality (ie, userspace) I'm
confident we'll need to submit a few more patches. The only concrete
issues I know about are the sys_riscv_flush_icache patches, but as I
managed to screw those up on Friday I figured it'd be best to let them
bake another week.
This tag boots a Fedora root filesystem on QEMU's master branch for
me, and before this morning's rebase (from 4.18-rc8 to 4.18) it booted
on the HiFive Unleashed.
Thanks to Christoph Hellwig and the other guys at WD for getting the
new drivers in shape!"
* tag 'riscv-for-linus-4.19-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
dt-bindings: interrupt-controller: SiFive Plaform Level Interrupt Controller
dt-bindings: interrupt-controller: RISC-V local interrupt controller
RISC-V: Fix !CONFIG_SMP compilation error
irqchip: add a SiFive PLIC driver
RISC-V: Add the directive for alignment of stvec's value
clocksource: new RISC-V SBI timer driver
RISC-V: implement low-level interrupt handling
RISC-V: add a definition for the SIE SEIE bit
RISC-V: remove INTERRUPT_CAUSE_* defines from asm/irq.h
RISC-V: simplify software interrupt / IPI code
RISC-V: remove timer leftovers
RISC-V: Add early printk support via the SBI console
RISC-V: Don't increment sepc after breakpoint.
RISC-V: implement __lshrti3.
RISC-V: Use KBUILD_CFLAGS instead of KCFLAGS when building the vDSO
Pull input updates from Dmitry Torokhov:
- a new driver for Rohm BU21029 touch controller
- new bitmap APIs: bitmap_alloc, bitmap_zalloc and bitmap_free
- updates to Atmel, eeti. pxrc and iforce drivers
- assorted driver cleanups and fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
MAINTAINERS: Add PhoenixRC Flight Controller Adapter
Input: do not use WARN() in input_alloc_absinfo()
Input: mark expected switch fall-throughs
Input: raydium_i2c_ts - use true and false for boolean values
Input: evdev - switch to bitmap API
Input: gpio-keys - switch to bitmap_zalloc()
Input: elan_i2c_smbus - cast sizeof to int for comparison
bitmap: Add bitmap_alloc(), bitmap_zalloc() and bitmap_free()
md: Avoid namespace collision with bitmap API
dm: Avoid namespace collision with bitmap API
Input: pm8941-pwrkey - add resin entry
Input: pm8941-pwrkey - abstract register offsets and event code
Input: iforce - reorganize joystick configuration lists
Input: atmel_mxt_ts - move completion to after config crc is updated
Input: atmel_mxt_ts - don't report zero pressure from T9
Input: atmel_mxt_ts - zero terminate config firmware file
Input: atmel_mxt_ts - refactor config update code to add context struct
Input: atmel_mxt_ts - config CRC may start at T71
Input: atmel_mxt_ts - remove unnecessary debug on ENOMEM
Input: atmel_mxt_ts - remove duplicate setup of ABS_MT_PRESSURE
...
This fixes a few compile and kerneldoc warnings, allows rpmsg devices to
handle power domains, allow for labeling GLINK edges and supports compat
for rpmsg_char.
-----BEGIN PGP SIGNATURE-----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=aTVF
-----END PGP SIGNATURE-----
Merge tag 'rpmsg-v4.19' of git://github.com/andersson/remoteproc
Pull rpmsg updates from Bjorn Andersson:
"This fixes a few compile and kerneldoc warnings, allows rpmsg devices
to handle power domains, allow for labeling GLINK edges and supports
compat for rpmsg_char"
* tag 'rpmsg-v4.19' of git://github.com/andersson/remoteproc:
rpmsg: Add compat ioctl for rpmsg char driver
rpmsg: glink: Store edge name for glink device
dt-bindings: soc: qcom: Add label for GLINK bindings
rpmsg: core: add support to power domains for devices
rpmsg: smd: fix kerneldoc warnings
rpmsg: glink: Fix various kerneldoc warnings.
rpmsg: glink: correctly annotate intent members
rpmsg: smd: Add missing include of sizes.h
This adds support for pre-start and post-shutdown hooks for remoteproc
subdevices, refactors the Qualcomm Hexagon support to allow reuse
between several drivers, makes authentication in the MDT file loader
optional, migrates a few format strings to use %pK and migrates the
Davinci driver to use the reset framework.
-----BEGIN PGP SIGNATURE-----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=QpCe
-----END PGP SIGNATURE-----
Merge tag 'rproc-v4.19' of git://github.com/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This adds support for pre-start and post-shutdown hooks for remoteproc
subdevices, refactors the Qualcomm Hexagon support to allow reuse
between several drivers, makes authentication in the MDT file loader
optional, migrates a few format strings to use %pK and migrates the
Davinci driver to use the reset framework"
* tag 'rproc-v4.19' of git://github.com/andersson/remoteproc:
remoteproc/davinci: use the reset framework
remoteproc/davinci: Mark error recovery as disabled
remoteproc: st_slim: replace "%p" with "%pK"
remoteproc: replace "%p" with "%pK"
remoteproc: qcom: fix Q6V5_WCSS dependencies
remoteproc: Reset table_ptr in rproc_start() failure paths
remoteproc: qcom: q6v5-pil: fix modem hang on SDM845 after axis2 clk unvote
remoteproc: qcom q6v5: fix modular build
remoteproc: Introduce prepare and unprepare for subdevices
remoteproc: rename subdev probe and remove functions
remoteproc: Make client initialize ops in rproc_subdev
remoteproc: Make start and stop in subdev optional
remoteproc: Rename subdev functions to start/stop
remoteproc: qcom: Introduce Hexagon V5 based WCSS driver
remoteproc: qcom: q6v5-pil: Use common q6v5 helpers
remoteproc: qcom: adsp: Use common q6v5 helpers
remoteproc: q6v5: Extract common resource handling
remoteproc: qcom: mdt_loader: Make the firmware authentication optional
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAlt2pvIACgkQ+iyteGJfRspSxgCggHiSqO+sb1F+h4QyWlh45o9S
laAAoJL0ZAXSrlA/rAt5FCKCeSZiNZG2
=hCTY
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-4.19-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- add MEN 16z069 IP-Core driver
- renesas-wdt: add support for the R8A77990 wdt
- stm32_iwdg: Add stm32mp1 support and pclk feature
- sp805_wdt, orion_wdt, sprd_wdt: several improvements
- imx2_wdt, stmp3xxx: switch to SPDX identifier
* tag 'linux-watchdog-4.19-rc1' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: fix dependencies of menz69_wdt.o
watchdog: sp805: Add clock-frequency property
watchdog: add driver for the MEN 16z069 IP-Core
watchdog: sprd_wdt: Remove redundant dev_err call in sprd_wdt_probe()
watchdog: stmp3xxx: Switch to SPDX identifier
watchdog: imx2_wdt: Switch to SPDX identifier
watchdog: sp805: set WDOG_HW_RUNNING when appropriate
watchdog: sp805: add 'timeout-sec' DT property support
dt-bindings: watchdog: Add optional 'timeout-sec' property for sp805
dt-bindings: watchdog: Consolidate SP805 binding docs
watchdog: orion_wdt: Mark watchdog as active when running at probe
watchdog: stm32: add pclk feature for stm32mp1
dt-bindings: watchdog: add stm32mp1 support
dt-bindings: watchdog: renesas-wdt: Add support for the R8A77990 wdt
This round brings couple of framework changes, a new driver and usual driver
updates:
- New managed helper for dmaengine framework registration
- Split dmaengine pause capability to pause and resume and allow drivers to
report that individually
- Update dma_request_chan_by_mask() to handle deferred probing
- Move imx-sdma to use virt-dma
- New driver for Actions Semi Owl family S900 controller
- Minor updates to intel, renesas, mv_xor, pl330 etc
-----BEGIN PGP SIGNATURE-----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=kbCC
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.19-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull DMAengine updates from Vinod Koul:
"This round brings couple of framework changes, a new driver and usual
driver updates:
- new managed helper for dmaengine framework registration
- split dmaengine pause capability to pause and resume and allow
drivers to report that individually
- update dma_request_chan_by_mask() to handle deferred probing
- move imx-sdma to use virt-dma
- new driver for Actions Semi Owl family S900 controller
- minor updates to intel, renesas, mv_xor, pl330 etc"
* tag 'dmaengine-4.19-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (46 commits)
dmaengine: Add Actions Semi Owl family S900 DMA driver
dt-bindings: dmaengine: Add binding for Actions Semi Owl SoCs
dmaengine: sh: rcar-dmac: Should not stop the DMAC by rcar_dmac_sync_tcr()
dmaengine: mic_x100_dma: use the new helper to simplify the code
dmaengine: add a new helper dmaenginem_async_device_register
dmaengine: imx-sdma: add memcpy interface
dmaengine: imx-sdma: add SDMA_BD_MAX_CNT to replace '0xffff'
dmaengine: dma_request_chan_by_mask() to handle deferred probing
dmaengine: pl330: fix irq race with terminate_all
dmaengine: Revert "dmaengine: mv_xor_v2: enable COMPILE_TEST"
dmaengine: mv_xor_v2: use {lower,upper}_32_bits to configure HW descriptor address
dmaengine: mv_xor_v2: enable COMPILE_TEST
dmaengine: mv_xor_v2: move unmap to before callback
dmaengine: mv_xor_v2: convert callback to helper function
dmaengine: mv_xor_v2: kill the tasklets upon exit
dmaengine: mv_xor_v2: explicitly freeup irq
dmaengine: sh: rcar-dmac: Add dma_pause operation
dmaengine: sh: rcar-dmac: add a new function to clear CHCR.DE with barrier
dmaengine: idma64: Support dmaengine_terminate_sync()
dmaengine: hsu: Support dmaengine_terminate_sync()
...
- Add some fine-grained hooks to further support HS400 tuning
- Improve error path for bus width setting for HS400es
- Use a common method when checking R1 status
MMC host:
- renesas_sdhi: Add r8a77990 support
- renesas_sdhi: Add eMMC HS400 mode support
- tmio/renesas_sdhi: Improve tuning/clock management
- tmio: Add eMMC HS400 mode support
- sunxi: Add support for 3.3V eMMC DDR mode
- mmci: Initial support to manage variant specific callbacks
- sdhci: Don't try 3.3V I/O voltage if not supported
- sdhci-pci-dwc-mshc: Add driver to support Synopsys dwc mshc SDHCI PCI
- sdhci-of-dwcmshc: Add driver to support Synopsys DWC MSHC SDHCI
- sdhci-msm: Add support for new version sdcc V5
- sdhci-pci-o2micro: Add support for O2 eMMC HS200 mode
- sdhci-pci-o2micro: Add support for O2 hardware tuning
- sdhci-pci-o2micro: Add MSI interrupt support for O2 SD host
- sdhci-pci: Add support for Intel ICP
- sdhci-tegra: Prevent ACMD23 and HS200 mode on Tegra 3
- sdhci-tegra: Fix eMMC DDR52 mode
- sdhci-tegra: Improve clock management
- dw_mmc-rockchip: Document compatible string for px30
- sdhci-esdhc-imx: Add support for 3.3V eMMC DDR mode
- sdhci-of-esdhc: Set proper DMA mask for ls104x chips
- sdhci-of-esdhc: Improve clock management
- sdhci-of-arasan: Add a quirk to manage unstable clocks
- dw_mmc-exynos: Address potential external abort during system resume
- pxamci: Add support for common MMC DT bindings
- pxamci: Several cleanups and improvements
- pxamci: Merge immutable branch for pxa to switch to DMA slave maps
-----BEGIN PGP SIGNATURE-----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=5jpq
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"Updates for MMC for v4.19.
MMC core:
- Add some fine-grained hooks to further support HS400 tuning
- Improve error path for bus width setting for HS400es
- Use a common method when checking R1 status
MMC host:
- renesas_sdhi: Add r8a77990 support
- renesas_sdhi: Add eMMC HS400 mode support
- tmio/renesas_sdhi: Improve tuning/clock management
- tmio: Add eMMC HS400 mode support
- sunxi: Add support for 3.3V eMMC DDR mode
- mmci: Initial support to manage variant specific callbacks
- sdhci: Don't try 3.3V I/O voltage if not supported
- sdhci-pci-dwc-mshc: Add driver to support Synopsys dwc mshc SDHCI PCI
- sdhci-of-dwcmshc: Add driver to support Synopsys DWC MSHC SDHCI
- sdhci-msm: Add support for new version sdcc V5
- sdhci-pci-o2micro: Add support for O2 eMMC HS200 mode
- sdhci-pci-o2micro: Add support for O2 hardware tuning
- sdhci-pci-o2micro: Add MSI interrupt support for O2 SD host
- sdhci-pci: Add support for Intel ICP
- sdhci-tegra: Prevent ACMD23 and HS200 mode on Tegra 3
- sdhci-tegra: Fix eMMC DDR52 mode
- sdhci-tegra: Improve clock management
- dw_mmc-rockchip: Document compatible string for px30
- sdhci-esdhc-imx: Add support for 3.3V eMMC DDR mode
- sdhci-of-esdhc: Set proper DMA mask for ls104x chips
- sdhci-of-esdhc: Improve clock management
- sdhci-of-arasan: Add a quirk to manage unstable clocks
- dw_mmc-exynos: Address potential external abort during system resume
- pxamci: Add support for common MMC DT bindings
- pxamci: Several cleanups and improvements
- pxamci: Merge immutable branch for pxa to switch to DMA slave maps"
* tag 'mmc-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (56 commits)
mmc: core: improve reasonableness of bus width setting for HS400es
mmc: tmio: remove unneeded variable in tmio_mmc_start_command()
mmc: renesas_sdhi: Fix sampling clock position selecting
mmc: tmio: Fix tuning flow
mmc: sunxi: remove output of virtual base address
dt-bindings: mmc: rockchip-dw-mshc: add description for px30
mmc: renesas_sdhi: Add r8a77990 support
mmc: sunxi: allow 3.3V DDR when DDR is available
mmc: mmci: Add and implement a ->dma_setup() callback for qcom dml
mmc: mmci: Initial support to manage variant specific callbacks
mmc: tegra: Force correct divider calculation on DDR50/52
mmc: sdhci: Add MSI interrupt support for O2 SD host
mmc: sdhci: Add support for O2 hardware tuning
mmc: sdhci: Export sdhci tuning function symbol
mmc: sdhci: Change O2 Host HS200 mode clock frequency to 200MHz
mmc: sdhci: Add support for O2 eMMC HS200 mode
mmc: tegra: Add and use tegra_sdhci_get_max_clock()
mmc: sdhci-esdhc-imx: fix indent
mmc: sdhci-esdhc-imx: disable clocks before changing frequency
mmc: tegra: prevent ACMD23 on Tegra 3
...
Here are all of the driver core and related patches for 4.19-rc1.
Nothing huge here, just a number of small cleanups and the ability to
now stop the deferred probing after init happens.
All of these have been in linux-next for a while with only a merge issue
reported. That merge issue is in fs/sysfs/group.c and Stephen has
posted the diff of what it should be to resolve this. I'll follow up
with that diff to this pull request.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g86Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynyXQCePaZSW8wft4b7nLN8RdZ98ATBru0Ani10lrJa
HQeQJRNbWU1AZ0ym7695
=tOaH
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here are all of the driver core and related patches for 4.19-rc1.
Nothing huge here, just a number of small cleanups and the ability to
now stop the deferred probing after init happens.
All of these have been in linux-next for a while with only a merge
issue reported"
* tag 'driver-core-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (21 commits)
base: core: Remove WARN_ON from link dependencies check
drivers/base: stop new probing during shutdown
drivers: core: Remove glue dirs from sysfs earlier
driver core: remove unnecessary function extern declare
sysfs.h: fix non-kernel-doc comment
PM / Domains: Stop deferring probe at the end of initcall
iommu: Remove IOMMU_OF_DECLARE
iommu: Stop deferring probe at end of initcalls
pinctrl: Support stopping deferred probe after initcalls
dt-bindings: pinctrl: add a 'pinctrl-use-default' property
driver core: allow stopping deferred probe after init
driver core: add a debugfs entry to show deferred devices
sysfs: Fix internal_create_group() for named group updates
base: fix order of OF initialization
linux/device.h: fix kernel-doc notation warning
Documentation: update firmware loader fallback reference
kobject: Replace strncpy with memcpy
drivers: base: cacheinfo: use OF property_read_u32 instead of get_property,read_number
kernfs: Replace strncpy with memcpy
device: Add #define dev_fmt similar to #define pr_fmt
...
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
Here are the big staging/iio patches for 4.19-rc1.
Lots of churn here, with tons of cleanups happening in staging drivers,
a removal of an old crypto driver that no one was using (skein), and the
addition of some new IIO drivers. Also added was a "gasket" driver from
Google that needs loads of work and the erofs filesystem.
Even with adding all of the new drivers and a new filesystem, we are
only adding about 1000 lines overall to the kernel linecount, which
shows just how much cleanup happened, and how big the unused crypto
driver was.
All of these have been in the linux-next tree for a while now with no
reported issues.
Note, you will have a merge problem with a device tree IIO file and the
MAINTAINERS file, both resolutions are easy, just take all changed.
There will be a skein file merge issue as well, but that file got
deleted so just drop that.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g+2A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykwGACfQZz3Ncvc7thHkZytxxqQnbx5JpkAn0yV5SvF
yVXG9SA9yCTKVjYczZjZ
=6t/x
-----END PGP SIGNATURE-----
Merge tag 'staging-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here are the big staging/iio patches for 4.19-rc1.
Lots of churn here, with tons of cleanups happening in staging
drivers, a removal of an old crypto driver that no one was using
(skein), and the addition of some new IIO drivers. Also added was a
"gasket" driver from Google that needs loads of work and the erofs
filesystem.
Even with adding all of the new drivers and a new filesystem, we are
only adding about 1000 lines overall to the kernel linecount, which
shows just how much cleanup happened, and how big the unused crypto
driver was.
All of these have been in the linux-next tree for a while now with no
reported issues"
* tag 'staging-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (903 commits)
staging:rtl8192u: Remove unused macro definitions - Style
staging:rtl8192u: Add spaces around '+' operator - Style
staging:rtl8192u: Remove stale comment - Style
staging: rtl8188eu: remove unused mp_custom_oid.h
staging: fbtft: Add spaces around / - Style
staging: fbtft: Erases some repetitive usage of function name - Style
staging: fbtft: Adjust some empty-line problems - Style
staging: fbtft: Removes one nesting level to help readability - Style
staging: fbtft: Changes gamma table to define.
staging: fbtft: A bit more information on dev_err.
staging: fbtft: Fixes some alignment issues - Style
staging: fbtft: Puts macro arguments in parenthesis to avoid precedence issues - Style
staging: rtl8188eu: remove unused array dB_Invert_Table
staging: rtl8188eu: remove whitespace, add missing blank line
staging: rtl8188eu: use is_multicast_ether_addr in rtw_sta_mgt.c
staging: rtl8188eu: remove whitespace - style
staging: rtl8188eu: cleanup block comment - style
staging: rtl8188eu: use is_multicast_ether_addr in rtl8188eu_xmit.c
staging: rtl8188eu: use is_multicast_ether_addr in recv_linux.c
staging: rtlwifi: refactor rtl_get_tcb_desc
...
Here is the big tty and serial driver pull request for 4.19-rc1.
It's not all that big, just a number of small serial driver updates and
fixes, along with some better vt handling for unicode characters for
those using braille terminals.
Full details are in the shortlog.
All of these patches have been in linux-next for a long time with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g/5Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynZDwCdETeD4sIqt06hXeG4ADiVORb3gLgAnjJTbl9Y
reffAFDRWrwD42SvTi1X
=7tX/
-----END PGP SIGNATURE-----
Merge tag 'tty-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big tty and serial driver pull request for 4.19-rc1.
It's not all that big, just a number of small serial driver updates
and fixes, along with some better vt handling for unicode characters
for those using braille terminals.
All of these patches have been in linux-next for a long time with no
reported issues"
* tag 'tty-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (73 commits)
tty: serial: 8250: Revert NXP SC16C2552 workaround
serial: 8250_exar: Read INT0 from slave device, too
tty: rocket: Fix possible buffer overwrite on register_PCI
serial: 8250_dw: Add ACPI support for uart on Broadcom SoC
serial: 8250_dw: always set baud rate in dw8250_set_termios
dt-bindings: serial: Add binding for uartlite
tty: serial: uartlite: Add support for suspend and resume
tty: serial: uartlite: Add clock adaptation
tty: serial: uartlite: Add structure for private data
serial: sh-sci: Improve support for separate TEI and DRI interrupts
serial: sh-sci: Remove SCIx_RZ_SCIFA_REGTYPE
serial: sh-sci: Allow for compressed SCIF address
serial: sh-sci: Improve interrupts description
serial: 8250: Use cached port name directly in messages
serial: 8250_exar: Drop unused variable in pci_xr17v35x_setup()
vt: drop unused struct vt_struct
vt: avoid a VLA in the unicode screen scroll function
vt: add /dev/vcsu* to devices.txt
vt: coherence validation code for the unicode screen buffer
vt: selection: take screen contents from uniscr if available
...
Here is the big USB and phy driver patch set for 4.19-rc1.
Nothing huge but there was a lot of work that happened this development
cycle:
- lots of type-c work, with drivers graduating out of staging,
and displayport support being added.
- new PHY drivers
- the normal collection of gadget driver updates and fixes
- code churn to work on the urb handling path, using irqsave()
everywhere in anticipation of making this codepath a lot
simpler in the future.
- usbserial driver fixes and reworks
- other misc changes
Full details are in the shortlog.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3hBPA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yloNwCggMZi9m8Krjq7d7aLw5oJJex/nIAAn0jeADOT
NpoCgrtGHjwrATxN5/Ke
=jXa3
-----END PGP SIGNATURE-----
Merge tag 'usb-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB and phy driver patch set for 4.19-rc1.
Nothing huge but there was a lot of work that happened this
development cycle:
- lots of type-c work, with drivers graduating out of staging, and
displayport support being added.
- new PHY drivers
- the normal collection of gadget driver updates and fixes
- code churn to work on the urb handling path, using irqsave()
everywhere in anticipation of making this codepath a lot simpler in
the future.
- usbserial driver fixes and reworks
- other misc changes
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (159 commits)
USB: serial: pl2303: add a new device id for ATEN
usb: renesas_usbhs: Kconfig: convert to SPDX identifiers
usb: dwc3: gadget: Check MaxPacketSize from descriptor
usb: dwc2: Turn on uframe_sched on "stm32f4x9_fsotg" platforms
usb: dwc2: Turn on uframe_sched on "amlogic" platforms
usb: dwc2: Turn on uframe_sched on "his" platforms
usb: dwc2: Turn on uframe_sched on "bcm" platforms
usb: dwc2: gadget: ISOC's starting flow improvement
usb: dwc2: Make dwc2_readl/writel functions endianness-agnostic.
usb: dwc3: core: Enable AutoRetry feature in the controller
usb: dwc3: Set default mode for dwc_usb31
usb: gadget: udc: renesas_usb3: Add register of usb role switch
usb: dwc2: replace ioread32/iowrite32_rep with dwc2_readl/writel_rep
usb: dwc2: Modify dwc2_readl/writel functions prototype
usb: dwc3: pci: Intel Merrifield can be host
usb: dwc3: pci: Supply device properties via driver data
arm64: dts: dwc3: description of incr burst type
usb: dwc3: Enable undefined length INCR burst type
usb: dwc3: add global soc bus configuration reg0
usb: dwc3: Describe 'wakeup_work' field of struct dwc3_pci
...
ksz9477 is superset of ksz9xx series, driver just works
out of the box for ksz9897 chip with this patch.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document RZ/G2M (R8A774A1) SoC bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull thermal management updates from Eduardo Valentin:
- rework tsens driver to add support for tsens-v2 (Amit Kucheria)
- rework armada thermal driver to use syscon and multichannel support
(Miquel Raynal)
- fixes to TI SoC, IMX, Exynos, RCar, and hwmon drivers
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal: (34 commits)
thermal: armada: fix copy-paste error in armada_thermal_probe()
thermal: rcar_thermal: avoid NULL dereference in absence of IRQ resources
thermal: samsung: Remove Exynos5440 clock handling left-overs
thermal: tsens: Fix negative temperature reporting
thermal: tsens: switch from of_iomap() to devm_ioremap_resource()
thermal: tsens: Rename variable
thermal: tsens: Add generic support for TSENS v2 IP
thermal: tsens: Rename tsens-8996 to tsens-v2 for reuse
thermal: tsens: Add support to split up register address space into two
dt: thermal: tsens: Document the fallback DT property for v2 of TSENS IP
thermal: tsens: Get rid of unused fields in structure
thermal_hwmon: Pass the originating device down to hwmon_device_register_with_info
thermal_hwmon: Sanitize attribute name passed to hwmon
dt-bindings: thermal: armada: add reference to new bindings
dt-bindings: cp110: add the thermal node in the syscon file
dt-bindings: cp110: update documentation since DT de-duplication
dt-bindings: ap806: add the thermal node in the syscon file
dt-bindings: cp110: prepare the syscon file to list other syscons nodes
dt-bindings: ap806: prepare the syscon file to list other syscons nodes
dt-bindings: cp110: rename cp110 syscon file
...
- omap : switch to spdx license and use of_device_get_match_data() to match data
- ti-msgmgr : cleanup and optimisation. New TI specific feature - secure proxy thread.
- mediatek : add driver for CMDQ controller.
- nxp : add driver for MU controller
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE6EwehDt/SOnwFyTyf9lkf8eYP5UFAlt1nhUACgkQf9lkf8eY
P5XbBg/9FAzw6wEhyBQUdybM6sv1UrQYPbe5bgpbRgS6quQMtDOIuCBAbznPkGp5
ZeDsQ+CTK7UzUSG5QQEjdrb5L2NWzsXWRY8pp8XEwYFLCFmM8siPPf0NIuOHZUcg
VkHAXOAFKzOqFKJHQ54ISgJzUweMx215jGF/PVUDFy6mNK9KpSIJJjmY9LCaiuav
sOajNx/DuTl7DU+eDECQhHKYZdsSlBAnMYVk1nNQj3E/vMWgkuL421WrRckLf5T6
Y2eAy7sid50+ZpwK5dFqJmGJgxyWo6b9C4qCX0dq4E0RDi1jYt9bmwo0RckIQSk4
aTqYcNF3pwkl0EUMz+EKi3cc2G07ufX8H88jBW9xj8j4xaNBQJjPfimp2nhVBLqJ
cesW+0QxdERBj48hw5EsL0lXwQ7sKlpIkg2PfmcDRLoJZynCM6TDil4+Xt9k5tkZ
yoPcuVHQ+YAkY0a03v04daRySc3KEXJ814M396bE/nz+Y8EVm7WPlB2KtqHS/1Rv
9kQWM+MBewtHOMuM8D8TAEVVjyfYfWuWb2F/6JugdedYYuAcbmpdNFaPs1Be9QVg
RywNzEuWrrC/qvfYLQS9GD6dCGij62ErnSvP9UQjiXMcBoRwSQky7gzD+2DxabPb
1h3rPUtw9at0rHYlIaozpsRKrrIlkOcH6uey7vFvb30XLL3OCRk=
=6YOd
-----END PGP SIGNATURE-----
Merge tag 'mailbox-v4.19' of git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox updates from Jassi Brar:
- xgene: potential null pointer fix
- omap: switch to spdx license and use of_device_get_match_data() to
match data
- ti-msgmgr: cleanup and optimisation. New TI specific feature - secure
proxy thread.
- mediatek: add driver for CMDQ controller.
- nxp: add driver for MU controller
* tag 'mailbox-v4.19' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: Add support for i.MX messaging unit
dt-bindings: mailbox: imx-mu: add generic MU channel support
dt-bindings: arm: fsl: add mu binding doc
mailbox: add MODULE_LICENSE() for mtk-cmdq-mailbox.c
mailbox: mediatek: Add Mediatek CMDQ driver
dt-bindings: soc: Add documentation for the MediaTek GCE unit
mailbox: ti-msgmgr: Add support for Secure Proxy
dt-bindings: mailbox: Add support for secure proxy threads
mailbox: ti-msgmgr: Move the memory region name to descriptor
mailbox: ti-msgmgr: Change message count mask to be descriptor based
mailbox: ti-msgmgr: Allocate Rx channel resources only on request
mailbox: ti-msgmgr: Get rid of unused structure members
mailbox/omap: use of_device_get_match_data() to get match data
mailbox/omap: switch to SPDX license identifier
mailbox: xgene-slimpro: Fix potential NULL pointer dereference
Peter Rosin