This patch adds the PHY_HAS_INTERRUPT flag for IC+101 device series.
Also the patch does a simple dity-up to signal that
the driver actually is for IP101A LF and IP101G devices.
In fact, these are two similar PHYs that have the same IDs
and mainly differ for the EEE capability supported in the
G series.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for ip1001_config_init() was totally broken if you were not
using RGMII. Instead of returning an error code or zero it actually
returned the value in the IP1001_SPEC_CTRL_STATUS_2 register. It was
also trying to set the IP1001_APS_ON bit , but never actually wrote
back the register.
The error checking was also incorrect in both this function and the
reset function, so this patch fixes that up in a consistent fashion.
Signed-off-by: David McKay <david.mckay@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Niccolo Belli reported ipsec crashes in case we handle a frame without
mac header (atm in his case)
Before copying mac header, better make sure it is present.
Bugzilla reference: https://bugzilla.kernel.org/show_bug.cgi?id=42809
Reported-by: Niccolò Belli <darkbasic@linuxsystems.it>
Tested-by: Niccolò Belli <darkbasic@linuxsystems.it>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BenH says:
'Here are a few more powerpc bits for you. A stupid regression I
introduced with my previous commit to "fix" program check exceptions
(brown paper bag for me), fix the cpuidle default, a bug fix for
something that isn't strictly speaking a regression but some upstream
changes causes it to show in lockdep now while it didn't before, and
finally a trivial one for rusty to make his life easier later on
removing the old cpumask cruft. '
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix various issues with return to userspace
cpuidle: Default y on powerpc pSeries
powerpc: Fix program check handling when lockdep is enabled
powerpc: Remove references to cpu_*_map
When doing IO with large amounts of data fragmentation, the global block
reserve calulations are too low. This increases them to avoid
ENOSPC crashes.
Signed-off-by: Liu Bo <liubo2009@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
If btrfs reads a block and finds a parent transid mismatch, it clears
the uptodate flags on the extent buffer, and the pages inside it. But
we only clear the uptodate bits in the state tree if the block straddles
more than one page.
This is from an old optimization from to reduce contention on the extent
state tree. But it is buggy because the code that retries a read from
a different copy of the block is going to find the uptodate state bits
set and skip the IO.
The end result of the bug is that we'll never actually read the good
copy (if there is one).
The fix here is to always clear the uptodate state bits, which is safe
because this code is only called when the parent transid fails.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
When we are setting up the mount, we close all the
devices that were not actually part of the metadata we found.
But, we don't make sure that one of those devices wasn't
fs_devices->latest_bdev, which means we can do a use after free
on the one we closed.
This updates latest_bdev as it goes.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This allows us to gracefully continue if we aren't able to insert
directory items, both for normal files/dirs and snapshots.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
By hwmon sysfs interface convention, setting pwm_enable to zero sets a fan
to full speed. In the f75375s driver, this need be done by enabling
manual fan control, plus duty mode for the F875387 chip, and then setting
the maximum duty cycle. Fix a bug where the two necessary register writes
were swapped, effectively discarding the setting to full-speed.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Cc: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
An error while creating sysfs attribute files in the driver's probe function
results in an error abort, but already created files are not removed. This patch
fixes the problem.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Cc: Dirk Eibach <eibach@gdsys.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
At least on powerpc, it breaks the build if exported functions are
static. Fix some static exported functions introduced with the mlx4
SR-IOV support added in 3.3-rc1.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The perf code has grown a lot since it started, and is big enough to
warrant its own subdirectory. For reference it's ~60% bigger than the
oprofile code. It declutters the kernel directory, makes it simpler to
grep for "just perf stuff", and allows us to shorten some filenames.
While we're at it, make it more obvious that we have two implementations
of the core perf logic. One for (roughly) Book3S CPUs, which was the
original implementation, and the other for Freescale embedded CPUs.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove the phyp assisted dump implementation which is not is use.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If dump is active during system reboot, shutdown or halt then invalidate
the fadump registration as it does not get invalidated automatically.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch introduces an sysfs interface '/sys/kernel/fadump_release_mem' to
invalidate the last fadump registration, invalidate '/proc/vmcore', release
the reserved memory for general use and re-register for future kernel dump.
Once the dump is copied to the disk, unlike phyp dump, the userspace tool
can release all the memory reserved for dump with one single operation of
echo 1 to '/sys/kernel/fadump_release_mem'.
Release the reserved memory region excluding the size of the memory required
for future kernel dump registration. And therefore, unlike kdump, Fadump
doesn't need a 2nd reboot to get back the system to the production
configuration.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With the firmware-assisted dump support we don't require a reboot when we
are in second kernel after crash. The second kernel after crash is a normal
kernel boot and has knowledge about entire system RAM with the page tables
initialized for entire system RAM. Hence once the dump is saved to disk, we
can just release the reserved memory area for general use and continue
with second kernel as production kernel.
Hence when we release the reserved memory that contains dump data, the
'/proc/vmcore' will not be valid anymore. Hence this patch introduces
a cleanup routine that invalidates and removes the /proc/vmcore file. This
routine will be invoked before we release the reserved dump memory area.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Introduce a PT_NOTE program header that points to physical address of
vmcoreinfo_note buffer declared in kernel/kexec.c. The vmcoreinfo
note buffer is populated during crash_fadump() at the time of system
crash.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When registered for firmware assisted dump on powerpc, firmware preserves
the registers for the active CPUs during a system crash. This patch reads
the cpu register data stored in Firmware-assisted dump format (except for
crashing cpu) and converts it into elf notes and updates the PT_NOTE program
header accordingly. The exact register state for crashing cpu is saved to
fadump crash info structure in scratch area during crash_fadump() and read
during second kernel boot.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Build the crash memory range list by traversing through system memory during
the first kernel before we register for firmware-assisted dump. After the
successful dump registration, initialize the elfcore header and populate
PT_LOAD program headers with crash memory ranges. The elfcore header is
saved in the scratch area within the reserved memory. The scratch area starts
at the end of the memory reserved for saving RMR region contents. The
scratch area contains fadump crash info structure that contains magic number
for fadump validation and physical address where the eflcore header can be
found. This structure will also be used to pass some important crash info
data to the second kernel which will help second kernel to populate ELF core
header with correct data before it gets exported through /proc/vmcore. Since
the firmware preserves the entire partition memory at the time of crash the
contents of the scratch area will be preserved till second kernel boot.
Since the memory dump exported through /proc/vmcore is in ELF format similar
to kdump, it will help us to reuse the kdump infrastructure for dump capture
and filtering. Unlike phyp dump, userspace tool does not need to refer any
sysfs interface while reading /proc/vmcore.
NOTE: The current design implementation does not address a possibility of
introducing additional fields (in future) to this structure without affecting
compatibility. It's on TODO list to come up with better approach to
address this.
Reserved dump area start => +-------------------------------------+
| CPU state dump data |
+-------------------------------------+
| HPTE region data |
+-------------------------------------+
| RMR region data |
Scratch area start => +-------------------------------------+
| fadump crash info structure { |
| magic nummber |
+------|---- elfcorehdr_addr |
| | } |
+----> +-------------------------------------+
| ELF core header |
Reserved dump area end => +-------------------------------------+
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On 2012-02-20 11:02:51 Mon, Paul Mackerras wrote:
> On Thu, Feb 16, 2012 at 04:44:30PM +0530, Mahesh J Salgaonkar wrote:
>
> If I have read the code correctly, we are going to get this printk on
> non-pSeries machines or on older pSeries machines, even if the user
> has not put the fadump=on option on the kernel command line. The
> printk will be annoying since there is no actual error condition. It
> seems to me that the condition for the printk should include
> fw_dump.fadump_enabled. In other words you should probably add
>
> if (!fw_dump.fadump_enabled)
> return 0;
>
> at the beginning of the function.
Hi Paul,
Thanks for pointing it out. Please find the updated patch below.
The existing patches above this (4/10 through 10/10) cleanly applies
on this update.
Thanks,
-Mahesh.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reserve the memory during early boot to preserve CPU state data, HPTE region
and RMA (real mode area) region data in case of kernel crash. At the time of
crash, powerpc firmware will store CPU state data, HPTE region data and move
RMA region data to the reserved memory area.
If the firmware-assisted dump fails to reserve the memory, then fallback
to existing kexec-based kdump.
Most of the code implementation to reserve memory has been
adapted from phyp assisted dump implementation written by Linas Vepstas
and Manish Ahuja
This patch also introduces a config option CONFIG_FA_DUMP for firmware
assisted dump feature on Powerpc (ppc64) architecture.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Documentation for firmware-assisted dump. This document is based on the
original documentation written for phyp assisted dump by Linas Vepstas
and Manish Ahuja, with few changes to reflect the current implementation.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are two separate flags controlling whether or not the MPIC is
reset during initialization, which is completely unnecessary, and only
one of them can be specified in the device tree.
Also, most platforms in-tree right now do actually want to reset the
MPIC during initialization anyways, which means lots of duplicate code
passing the MPIC_WANTS_RESET flag.
Fix all of the callers which currently do not pass the MPIC_WANTS_RESET
flag to pass the MPIC_NO_RESET flag, then remove the MPIC_WANTS_RESET
flag and make the code reset the MPIC by default.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The FreeScale PowerQUICC-III-compatible (mpc85xx/mpc86xx) MPICs do not
correctly report the number of hardware interrupt sources, so software
needs to override the detected value with "256".
To avoid needing to write custom board-specific code to detect that
scenario, allow it to be easily overridden in the device-tree.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The mpic->irq_count variable is only used as a software error-checking
limit to determine whether or not an IRQ number is valid. In board code
which does not manually specify an IRQ count to mpic_alloc(), i.e. 0, it
is automatically detected from the number of ISUs and the ISU size.
In practice, all hardware ends up with irq_count == num_sources, so all
of the runtime checks on mpic->irq_count should just check the value of
mpic->num_sources instead.
When platform hardware does not correctly report the number of IRQs,
which only happens on the MPC85xx/MPC86xx, the MPIC_BROKEN_FRR_NIRQS
flag is used to override the detected value of num_sources with the
manual irq_count parameter. Since there's no need to manually specify
the number of IRQs except in this case, the extra flag can be eliminated
and the test changed to "irq_count != 0".
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Freescale MPIC (and perhaps others in the future) is incapable of
routing non-IPI interrupts to more than once CPU at a time. Currently
all of the Freescale boards msut pass the MPIC_SINGLE_DEST_CPU flag to
mpic_alloc(), but that information should really be present in the
device-tree.
Older board code can't rely on the device-tree having the property set,
but newer platforms won't need it manually specified in the code.
[BenH: Remove unrelated changes, folded in a different patch]
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The MPIC code checks for a "big-endian" property and sets the flag
MPIC_BIG_ENDIAN if one is present, although prior to the "mpic->flags"
fixup that would never have worked anways.
Unfortunately, even now that it works properly, the Freescale mpic
device-node (the "PowerQUICC-III"-compatible one) does not specify it,
so all of the board ports need to manually pass it to mpic_alloc().
Document the flag and add it to the pq3 device tree. Existing code will
still need to pass the MPIC_BIG_ENDIAN flag because their dtb may not
have this property, but new platforms shouldn't need to do so.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The mpic_alloc() function takes a "flags" parameter and assigns it into
the mpic->flags variable fairly early on, but several later pieces of
code detect various device-tree properties and save them into the
"mpic->flags" variable (EG: "big-endian" => MPIC_BIG_ENDIAN).
Unfortunately, a number of codepaths (including several which test the
flag MPIC_BIG_ENDIAN!) test "flags" instead of "mpic->flags", and get
wrong answers as a result.
Consolidate the device-tree flag tests early in mpic_alloc() and change
all of the checks after "mpic->flags" is init'ed to use "mpic->flags".
[BenH: Fixed up use of mpic->node before it's initialized]
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A number of new device ids, and a cleanup/fix for some of the option
device ids that shouldn't have been added in the first place.
There's also a few USB 3 fixes for problems that people have reported,
and a usb-storage bugfix to round it out.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9FVQMACgkQMUfUDdst+ym7RgCeNfqK8Oi7U+9rdd2hGGIElxTE
6KgAnipmo5T5Wfls6sh0zPCv8Uh7K6Zb
=SXPd
-----END PGP SIGNATURE-----
Merge tag 'usb-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
USB bugfixes for 3.3-rc4
A number of new device ids, and a cleanup/fix for some of the option
device ids that shouldn't have been added in the first place.
There's also a few USB 3 fixes for problems that people have reported,
and a usb-storage bugfix to round it out.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'usb-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: Added Kamstrup VID/PIDs to cp210x serial driver.
USB: Serial: ti_usb_3410_5052: Add Abbot Diabetes Care cable id
usb-storage: fix freezing of the scanning thread
xhci: Fix encoding for HS bulk/control NAK rate.
USB: Set hub depth after USB3 hub reset
USB: Fix handoff when BIOS disables host PCI device.
USB: option: cleanup zte 3g-dongle's pid in option.c
USB: Don't fail USB3 probe on missing legacy PCI IRQ.
xhci: Fix oops caused by more USB2 ports than USB3 ports.
USB: Remove duplicate USB 3.0 hub feature #defines.
In the current kernel implementation, the Logitech Harmony 900 remote
control is matched to the cdc_ether driver through the generic
USB_CDC_SUBCLASS_MDLM entry. However, this device appears to be of the
pseudo-MDLM (Belcarra) type, rather than the standard one. This patch
blacklists the Harmony 900 from the cdc_ether driver and whitelists it for
the pseudo-MDLM driver in zaurus.
Signed-off-by: Scott Talbert <talbert@techie.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The intent was to clear out the icount struct here, but we accidentally
clear stack memory instead. It probably will lead to a NULL dereference
right away.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_route_output() never returns NULL, so it is wrong to
check if the return value is NULL.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_route_output() never returns NULL, so it is wrong to
check if the return value is NULL.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_route_output() never returns NULL, so it is wrong to
check if the return value is NULL.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intel, radeon, exynos fixes.
Intel: fixes a few Ivybridge hangs, along with fixing RC6 on SNB (still
not on, but at least allows for distros to patch it on easily).
radeon: oops reading some files in debugfs that weren't meant to appear,
a fix that touches a lot of files, so looks worse than it is, it fixes
an oops if a GPU reset fails and userspace keeps submitting more data,
along with a minor BIOS fix for newer boards.
exynos: a group of fixes for exynos, they've sent me a few more but
these were all I got through, and its no hw vanilla kernel users see a
lot off yet.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms/atom: dpms bios scratch reg updates
drm/radeon/kms: properly set accel working flag and bailout when false
drm/radeon: Only create additional ring debugfs files on Cayman or newer.
drm/exynos: added postclose to release resource.
drm/exynos: removed exynos_drm_fbdev_recreate function.
drm/exynos: fixed page flip issue.
drm/exynos: added possible_clones setup function.
drm/exynos: removed pageflip_event_list init code when closed.
drm/exynos: changed priority of mixer layers.
drm/exynos: Fix typo in exynos_mixer.c
drm/i915: do not enable RC6p on Sandy Bridge
drm/i915: gen7: Disable the RHWO optimization as it can cause GPU hangs.
drm/i915: gen7: work around a system hang on IVB
drm/i915: gen7: Implement an L3 caching workaround.
drm/i915: gen7: implement rczunit workaround
Set the RX FIFO flush watermark lower.
According to Federico and JMicron's reply,
setting it to 16QW would be stable on most platforms.
Otherwise, user might experience packet drop issue.
CC: stable@kernel.org
Reported-by: Federico Quagliata <federico@quagliata.org>
Fixed-by: Federico Quagliata <federico@quagliata.org>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It contains 3 important fixes for ColdFire based machines:
- fix processes getting stuck when running from strace
- fix kernel vmalloced pages not being visible in all kernel contexts
- fix shared user pages sometimes being visible in another process
context
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: Do not set global share for non-kernel shared pages
m68k: Add shared bit to Coldfire kernel page entries
m68knommu: fix syscall tracing stuck process
Fix a nasty Oops in the NFSv4 getacl code, another source of infinite loops
in the NFSv4 state recovery code, and a regression in NFSv4.1 session
initialisation.
Also deal with an NFSv4.1 memory leak.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yq1J
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.3-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Bugfixes for the NFS client.
Fix a nasty Oops in the NFSv4 getacl code, another source of infinite
loops in the NFSv4 state recovery code, and a regression in NFSv4.1
session initialisation.
Also deal with an NFSv4.1 memory leak.
* tag 'nfs-for-3.3-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: fix server_scope memory leak
NFSv4.1: Fix a NFSv4.1 session initialisation regression
NFSv4: Ensure we throw out bad delegation stateids on NFS4ERR_BAD_STATEID
NFSv4: Fix an Oops in the NFSv4 getacl code
If accel is not working many subsystem such as the ib pool might not be
initialized properly that can lead to segfault inside kernel when cs
ioctl is call with non working acceleration. To avoid this make sure
the accel working flag is false when an error in GPU startup happen and
return EBUSY from cs ioctl if accel is not working.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=46274
Tested with a Cayman card in a Llano system: The additional files are created
and working for the Cayman card but not created for the CPU's built-in GPU.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-intel:
drm/i915: do not enable RC6p on Sandy Bridge
drm/i915: gen7: Disable the RHWO optimization as it can cause GPU hangs.
drm/i915: gen7: work around a system hang on IVB
drm/i915: gen7: Implement an L3 caching workaround.
drm/i915: gen7: implement rczunit workaround
Commit 3702b08 added a lock, but did not account for the case of
SNDRV_PCM_POS_XRUN, which would get immediately overwritten.
This could be bundled into one if-else-if statement, but the goto
helps to clarify the 'exceptional' case.
Thanks to Andreas Pape for spotting this.
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 32092ecf06 (atm: clip: Use device neigh support on top of
"arp_tbl".) introduced a bug since clip_tbl is zeroed : Crash occurs in
__neigh_for_each_release()
idle_timer_check() must use instead arp_tbl and neigh_check_cb() should
ignore non clip neighbours.
Idea from David Miller.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a few problems when returning to userspace. This is a
quick set of fixes for 3.3, I'll look into a more comprehensive
rework for 3.4. This fixes:
- We kept interrupts soft-disabled when schedule'ing or calling
do_signal when returning to userspace as a result of a hardware
interrupt.
- Rename do_signal to do_notify_resume like all other archs (and
do_signal_pending back to do_signal, which it was before Roland
changed it).
- Add the missing call to key_replace_session_keyring() to
do_notify_resume().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
We moved all our pSeries idle loops to the cpu idle framework
so we really want it to come up by default.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Giuseppe CAVALLARO