After updates to checkpatch new warnings pops up this patch fixes them.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Acked-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Updated Firmware Info Metadata
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix random config build warnings:
Implicit-function-declaration ‘__raw_writel’
Cast to pointer from integer of different size [-Wint-to-pointer-cast]
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
At few places in caamhash and caamalg, after allocating a dmable
buffer for sg table , the buffer was being modified. As per
definition of DMA_FROM_DEVICE ,afer allocation the memory should
be treated as read-only by the driver. This patch shifts the
allocation of dmable buffer for sg table after it is populated
by the driver, making it read-only as per the DMA API's requirement.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CAAM IP has certain 64 bit registers . 32 bit architectures cannot force
atomic-64 operations. This patch adds definition of these atomic-64
operations for little endian platforms. The definitions which existed
previously were for big endian platforms.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For platforms with virtualization enabled
1. The job ring registers can be written to only is the job ring has been
started i.e STARTR bit in JRSTART register is 1
2. For DECO's under direct software control, with virtualization enabled
PL, BMT, ICID and SDID values need to be provided. These are provided by
selecting a Job ring in start mode whose parameters would be used for the
DECO access programming.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Some registers like SECVID, CHAVID, CHA Revision Number,
CTPR were defined as 64 bit resgisters. The IP provides
a DWT bit(Double word Transpose) to transpose the two words when
a double word register is accessed. However setting this bit
would also affect the operation of job descriptors as well as
other registers which are truly double word in nature.
So, for the IP to work correctly on big-endian as well as
little-endian SoC's, change is required to access all 32 bit
registers as 32 bit quantities.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
qat adds -I to the ccflags. Unfortunately it uses CURDIR which
breaks when make is invoked with O=. This patch replaces CURDIR
with $(src) which should work with/without O=.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The FIFOST_CONT_MASK define is cut and pasted twice so we can delete the
second instance.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Update to makefiles etc.
Don't update the firmware/Makefile yet since there is no FW binary in
the crypto repo yet. This will be added later.
v3 - removed change to ./firmware/Makefile
Reviewed-by: Bruce W. Allan <bruce.w.allan@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds DH895xCC hardware specific code.
It hooks to the common infrastructure and provides acceleration for crypto
algorithms.
Acked-by: John Griffin <john.griffin@intel.com>
Reviewed-by: Bruce W. Allan <bruce.w.allan@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds acceleration engine handler part the firmware loader.
Acked-by: Bo Cui <bo.cui@intel.com>
Reviewed-by: Bruce W. Allan <bruce.w.allan@intel.com>
Signed-off-by: Karen Xiang <karen.xiang@intel.com>
Signed-off-by: Pingchaox Yang <pingchaox.yang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds microcode part of the firmware loader.
v4 - splits FW loader part into two smaller patches.
Acked-by: Bo Cui <bo.cui@intel.com>
Reviewed-by: Bruce W. Allan <bruce.w.allan@intel.com>
Signed-off-by: Karen Xiang <karen.xiang@intel.com>
Signed-off-by: Pingchaox Yang <pingchaox.yang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds qat crypto interface.
Acked-by: John Griffin <john.griffin@intel.com>
Reviewed-by: Bruce W. Allan <bruce.w.allan@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds FW interface structure definitions.
Acked-by: John Griffin <john.griffin@intel.com>
Reviewed-by: Bruce W. Allan <bruce.w.allan@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds a code that implements communication channel between the
driver and the firmware.
Acked-by: John Griffin <john.griffin@intel.com>
Reviewed-by: Bruce W. Allan <bruce.w.allan@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds a common infractructure that will be used by all Intel(R)
QuickAssist Technology (QAT) devices.
v2 - added ./drivers/crypto/qat/Kconfig and ./drivers/crypto/qat/Makefile
v4 - splits common part into more, smaller patches
Acked-by: John Griffin <john.griffin@intel.com>
Reviewed-by: Bruce W. Allan <bruce.w.allan@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for the CCP on arm64 as a platform device.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Modify the PCI device support in prep for supporting the
CCP as a platform device for arm64.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
References to __exit functions must be wrapped with __exit_p.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Robert Jennings <rcj@linux.vnet.ibm.com>
Cc: Marcelo Henrique Cerri <mhcerri@linux.vnet.ibm.com>
Cc: Fionnuala Gunter <fin@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, linux/device.h is added to make sure the devm_*()
routine declarations are unambiguously available. Earlier, in the probe
function ctrlpriv was leaked on the failure of ctrl = of_iomap(nprop, 0);
as well as on the failure of ctrlpriv->jrpdev = kzalloc(...); . These
two bugs have been fixed by the patch.
The following Coccinelle semantic patch was used for making the change:
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The NX driver has endian issues so disable it for now.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The checking for the type of algorithm implementation is pretty
strange here. Use regular flags to check for the type instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use a standard accessor instead of directly digging into a structure.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: Michal Ludvig <michal@logix.cz>
Cc: Varun Wadekar <vwadekar@nvidia.com>
Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: linux-geode@lists.infradead.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Consistently use AES_KEYSIZE_128 instead of arbitrary defined value.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: Michal Ludvig <michal@logix.cz>
Cc: Varun Wadekar <vwadekar@nvidia.com>
Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: linux-geode@lists.infradead.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The AES IV length is always 128bits, just use the define from aes.h
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: Michal Ludvig <michal@logix.cz>
Cc: Varun Wadekar <vwadekar@nvidia.com>
Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: linux-geode@lists.infradead.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This is actually defined in include/crypto/aes.h , no need to have
a a different symbol for the same thing twice.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: Michal Ludvig <michal@logix.cz>
Cc: Varun Wadekar <vwadekar@nvidia.com>
Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: linux-geode@lists.infradead.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Re-initialize keys_fit_inline to avoid using its stale encrypt() shared
descriptor value prior to building descriptors for the decrypt() and
givencrypt() cases.
Signed-off-by: Vakul Garg <vakul@freescale.com>
[reworded commit text, enhanced code readability]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As we are preparing to enable multiplatform support on EXYNOS,
we can no longer include mach/*.h or plat/*.h headers from device
drivers.
The s5p-sss driver was just enabled for EXYNOS when it used to
be used only on s5pv210, and it includes two samsung platform
specific header files for historic reasons. Fortunately, it no
longer actually needs them, so we can remove the #includes and
avoid the problem
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: <linux-samsung-soc@vger.kernel.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently, the driver enqueues a request only if the busy bit is
false. And every request initiates a dequeue. If 2 requests arrive
simultaneously, only one of them will be dequeued.
To avoid this senario, we will enqueue the next request irrespective
of the system condition (that is what queue is here for). Also
schedule at a tasklet immediatly after the current request is done.
The tasklet will dequeue the next request in the queue, giving
continuous loop. tasklet will exit if there are no requests in the
queue.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
CC: David S. Miller <davem@davemloft.net>
CC: <linux-samsung-soc@vger.kernel.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch set adds use of clk_prepare/clk_unprepare as
required by generic clock framework.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
CC: David S. Miller <davem@davemloft.net>
CC: <linux-samsung-soc@vger.kernel.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds code to validate "iv" buffer before trying to
memcpy the contents
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
CC: David S. Miller <davem@davemloft.net>
CC: <linux-samsung-soc@vger.kernel.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch modifies Kconfig such that ARCH_EXYNOS SoCs
which includes (Exynos4210, Exynos5250 and Exynos5420)
can also select Samsung SSS(Security SubSystem) driver.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
CC: David S. Miller <davem@davemloft.net>
CC: <linux-samsung-soc@vger.kernel.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds new compatible and variant struct to support the SSS
module on Exynos4 (Exynos4210), Exynos5 (Exynos5420 and Exynos5250)
for which
1. AES register are at an offset of 0x200 and
2. hash interrupt is not available
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
CC: David S. Miller <davem@davemloft.net>
CC: <linux-samsung-soc@vger.kernel.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds device tree support to the s5p-sss.c crypto driver.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
CC: David S. Miller <davem@davemloft.net>
CC: <linux-samsung-soc@vger.kernel.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch uses the platform_get_irq() instead of the
platform_get_irq_byname(). Making feeder control interrupt
as resource "0" and hash interrupt as "1".
reasons for this change.
1. Cannot find any Arch which is currently using this driver
2. Samsung Exynos4 and 5 SoCs only use the feeder control interrupt
3. Patches adding support for DT and H/W version are in pipeline
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
CC: David S. Miller <davem@davemloft.net>
CC: <linux-samsung-soc@vger.kernel.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix the checkpatch warnings that the strings were split across
multiple lines. Checkpatch now complains about lines over 80,
but this is better, since we can actually grep the source code
for these strings now.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Clean up the remnants from the rework. Constify function arguments.
Note that checkpatch again complains about this space before newline,
but this is the original code behavior, so I'm keeping it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This macro is just like an encyclopedia of string handling done wrong.
This must die. This is so wrong on so many levels.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Clean this function up and rework it into sensible shape. This function
now contains one single dev_err() instead of the previous insanity full
of memory allocation, chaotic string handling and use of SPRINTFCAT().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Clean this function up and rework it into sensible shape. This function
now contains one single dev_err() instead of the previous insanity full
of memory allocation, possible stack overwriting, chaotic string handling
and use of SPRINTFCAT().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Just dissolve this function so it's not in the way of applying
further white magic cleanup down the line.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix the functions which can be obviously done right with a simple
dev_err() now. While at it, further press the on-stack allocation
of buffer for sprintf() voodoo down into the abominated functions.
This patch cleans up most of the functions and leaves just two
remaining functions, report_ccb_status() and report_deco_status()
ugly and unhappy.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pass the error type string into the functions, so they can handle
the printing of the string. This is now still using the very unsafe
sprintf(), but we will fix that.
While at this, pass the device pointer too, so we can dev_err()
functions readily when we start fixing this proper.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Implement fast-path error code printout for errors with no associated
handler function. This reduces calls to this kmalloc() nonsense in
SPRINTFCAT() already.
Note that the format of output is compatible with the old code, even
if -- exposed like this -- it looks a bit weird. Checkpatch complains
on this one as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull the error code <-> error string mapping tables out of the function
so the code becomes readable. This lets me see the real flesh of the
functions, without all that flab clouding the view.
Note: There is a checkpatch issue with quoted strings across multiple
lines. I will fix that in a subsequent patch to keep the changes
small and separate.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The tentacles of this function were firmly attached to various
places in the CAAM code. Just cut them, or this cthulhu function
will sprout them anew.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The length shoule be 64 bit alignment and the block size shoule be 64 bit in aes cfb64 mode.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The block size of aes cfb8 mode shoule be 8 bit.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In case hash key is bigger than algorithm block size, it is hashed.
In this case, memory is allocated to keep this hash in hashed_key.
hashed_key has to be freed on the key_dma dma mapping error path.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
pm_runtime_get_sync may not always succeed depending on SoC involved.
So handle the error appropriately ensuring usage_count is accurate in
case of failure.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reported-by: Joachim Eastwood <manabian@gmail.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
- The 4-byte sg_mid_buf is located in the middle of the coherence memory
sg_cpu. Don't call dma_map_single to get its physical address. Get the its
base physical address from the physical address of sg_cpu instead.
- Should set up the dma descriptor data after the 4-byte sg_mid_buf is
filled in completely from next sg buffer.
- memory copy from sg buffer should be done via virtual address.
- Remove unused reference to blackfin header
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
in case of multiple crc devices are probed.
Call platform_set_drvdata() before adding new CRC device into the list.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move architecture independant crc header file out of the blackfin folder.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_ioremap_resource() because devm_request_and_ioremap() is
obsoleted by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Joel Fernandes <joelf@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch replaces rcu_assign_pointer(x, NULL) with RCU_INIT_POINTER(x, NULL)
The rcu_assign_pointer() ensures that the initialization of a structure
is carried out before storing a pointer to that structure.
And in the case of the NULL pointer, there is no structure to initialize.
So, rcu_assign_pointer(p, NULL) can be safely converted to RCU_INIT_POINTER(p, NULL)
Signed-off-by: Monam Agarwal <monamagarwal123@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 3.15:
- Added 3DES driver for OMAP4/AM43xx
- Added AVX2 acceleration for SHA
- Added hash-only AEAD algorithms in caam
- Removed tegra driver as it is not functioning and the hardware is
too slow
- Allow blkcipher walks over AEAD (needed for ARM)
- Fixed unprotected FPU/SSE access in ghash-clmulni-intel
- Fixed highmem crash in omap-sham
- Add (zero entropy) randomness when initialising hardware RNGs
- Fixed unaligned ahash comletion functions
- Added soft module depedency for crc32c for initrds that use crc32c"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (60 commits)
crypto: ghash-clmulni-intel - use C implementation for setkey()
crypto: x86/sha1 - reduce size of the AVX2 asm implementation
crypto: x86/sha1 - fix stack alignment of AVX2 variant
crypto: x86/sha1 - re-enable the AVX variant
crypto: sha - SHA1 transform x86_64 AVX2
crypto: crypto_wq - Fix late crypto work queue initialization
crypto: caam - add missing key_dma unmap
crypto: caam - add support for aead null encryption
crypto: testmgr - add aead null encryption test vectors
crypto: export NULL algorithms defines
crypto: caam - remove error propagation handling
crypto: hash - Simplify the ahash_finup implementation
crypto: hash - Pull out the functions to save/restore request
crypto: hash - Fix the pointer voodoo in unaligned ahash
crypto: caam - Fix first parameter to caam_init_rng
crypto: omap-sham - Map SG pages if they are HIGHMEM before accessing
crypto: caam - Dynamic memory allocation for caam_rng_ctx object
crypto: allow blkcipher walks over AEAD data
crypto: remove direct blkcipher_walk dependency on transform
hwrng: add randomness to system from rng sources
...
(struct caam_ctx) ctx->key_dma needs to be unmapped
when context is cleaned up.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit 61bb86bba1
("crypto: caam - set descriptor sharing type to SERIAL")
changed the descriptor sharing mode from SHARE_WAIT to SHARE_SERIAL.
All descriptor commands that handle the "ok to share" and
"error propagation" settings should also go away, since they have no
meaning for SHARE_SERIAL.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Found by the kbuild test robot, the first argument to caam_init_rng
has a spurious ampersand.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
HIGHMEM pages may not be mapped so we must kmap them before accessing.
This resolves a random OOPs error that was showing up during OpenSSL SHA tests.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch allocates memory from DMAable region to the caam_rng_ctx object,
earlier it had been statically allocated which resulted in errorneous
behaviour on inserting the caamrng module at the runtime.
Signed-off-by: Nitesh Lal <NiteshNarayanLal@freescale.com>
Acked-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Optimize the hashing operation in the MXS-DCP by doing two adjustments:
1) Given that the output buffer for the hash is now always correctly aligned,
we can just use the buffer for the DCP DMA to store the resulting hash.
We thus get rid of one copying of data. Moreover, we remove an entry from
dcp_coherent_block{} and thus lower the memory footprint of the driver.
2) We map the output buffer for the hash for DMA only in case we will output
the hash, not always, as it was now.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The DCP needs the bounce buffers, DMA descriptors and result buffers aligned
to 64 bytes (yet another hardware limitation). Make sure they are aligned by
properly aligning the structure which contains them during allocation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Make omap_des_copy_needed(), omap_des_copy_sgs(), because these
functions are used only in this file.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use SIMPLE_DEV_PM_OPS macro in order to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
1) SSYNC instruction is blackfin specific and takes no effect in this driver.
2) DMA descriptor and SG middle buffer are in DMA coherent memory. No need
to flush.
3) Turn kzalloc, ioremap and request_irq into managed device APIs respectively.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When the crypto layer is able to queue up a command for processing
by the CCP on the initial call to ccp_crypto_enqueue_request and
the CCP returns -EBUSY, then if the backlog flag is not set the
command needs to be freed and not added to the active command list.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Invoke the callback routine associated with the crypto context
if an error is encountered sending the command to the CCP during
backlog processing. This is needed to free any resources used
by the command.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If a CCP command has been queued for processing at the
crypto layer then, when dequeueing it for processing, the
"can backlog" flag must be set so that the request isn't
lost if the CCP backlog queue limit is reached.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
My guess is that this little endian configuration is never found in real
life, but if it were then the writel() arguments are in the wrong order
so the driver would crash immediately.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has never been hooked up in any board file, and cannot be
instantiated via device tree. I've been told that, at least on Tegra20,
the HW is slower at crypto than the main CPU. I have no test-case for
it. Hence, remove it.
Cc: Varun Wadekar <vwadekar@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add config and build options for the omap-des driver.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add omap-des driver with platform data for OMAP4/AM43xx. Support added for DES
ECB and CBC modes. Also add support for 3DES operation where 3 64-bit keys are
used to perform a DES encrypt-decrypt-encrypt (des3_ede) operation on a buffer.
Tests have been conducted with the CRYPTO test manager, and functionality is
verified at different page length alignments.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We should test the error case for each platform_get_irq() assignment and
propagate the error accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The powerpc specific nx-842 compression driver does not currently
handle translating a vmalloc address to a physical address.
The current driver uses __pa() for all addresses which does not
properly handle vmalloc addresses and thus causes a failure since
we do not pass a proper physical address to the hypervisor.
This patch adds a routine to convert an address to a physical
address by checking for vmalloc addresses and handling them properly.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
---
drivers/crypto/nx/nx-842.c | 29 +++++++++++++++++++----------
1 file changed, 19 insertions(+), 10 deletions(-)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
SEC ERA has to be retrieved by reading the "fsl,sec-era" property
from the device tree. This property is updated/filled in by
u-boot.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Reviewed-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
stmp_reset_block() may fail, so check its return value and propagate it in the
case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Using devm_kzalloc() can make the code cleaner.
While at it, remove the devm_kzalloc error message as there is standard OOM
message done by the core.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In function talitos_probe(), it will jump to err_out when getting an
error in talitos_probe_irq(). Then the uninitialized list head
priv->alg_list will be used in function talitos_remove(). In this case
we would get a call trace like the following. So move up the
initialization of priv->alg_list.
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc0459ff4
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=8 P1020 RDB
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Tainted: G W 3.13.0-08789-g54c0a4b46150 #33
task: cf050000 ti: cf04c000 task.ti: cf04c000
NIP: c0459ff4 LR: c0459fd4 CTR: c02f2438
REGS: cf04dcb0 TRAP: 0300 Tainted: G W (3.13.0-08789-g54c0a4b46150)
MSR: 00029000 <CE,EE,ME> CR: 82000028 XER: 20000000
DEAR: 00000000 ESR: 00000000
GPR00: c045ac28 cf04dd60 cf050000 cf2579c0 00021000 00000000 c02f35b0 0000014e
GPR08: c07e702c cf104300 c07e702c 0000014e 22000024 00000000 c0002a3c 00000000
GPR16: 00000000 00000000 00000000 00000000 00000000 00000000 c082e4e0 000000df
GPR24: 00000000 00100100 00200200 cf257a2c cf0efe10 cf2579c0 cf0efe10 00000000
NIP [c0459ff4] talitos_remove+0x3c/0x1c8
LR [c0459fd4] talitos_remove+0x1c/0x1c8
Call Trace:
[cf04dd60] [c07485d8] __func__.13331+0x1241c8/0x1391c0 (unreliable)
[cf04dd90] [c045ac28] talitos_probe+0x244/0x998
[cf04dde0] [c0306a74] platform_drv_probe+0x28/0x68
[cf04ddf0] [c0304d38] really_probe+0x78/0x250
[cf04de10] [c030505c] __driver_attach+0xc8/0xcc
[cf04de30] [c0302e98] bus_for_each_dev+0x6c/0xb8
[cf04de60] [c03043cc] bus_add_driver+0x168/0x220
[cf04de80] [c0305798] driver_register+0x88/0x130
[cf04de90] [c0002458] do_one_initcall+0x14c/0x198
[cf04df00] [c079f904] kernel_init_freeable+0x138/0x1d4
[cf04df30] [c0002a50] kernel_init+0x14/0x124
[cf04df40] [c000ec40] ret_from_kernel_thread+0x5c/0x64
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Change from scheduling work to scheduling a tasklet to perform
the callback operations.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move to a single queue to serialize requests within a tfm. When
testing using IPSec with a large number of network connections
the per cpu tfm queuing logic was not working properly.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move the support to perform an HMAC calculation into
the CCP operations file. This eliminates the need to
perform a synchronous SHA operation used to calculate
the HMAC.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Introduce module parameters that allow for disabling of a
crypto algorithm by not registering the algorithm with the
crypto API.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There are some suspicious looking lines of code in the new ccp driver, including
one that assigns a variable to itself, and another that overwrites a previous assignment.
This may have been a cut-and-paste error where 'src' was forgotten to be changed to 'dst'.
I have no hardware to test this, so this is untested.
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The SEC Controller driver creates platform devices for it's child job ring nodes.
Currently the driver uses for_each_compatible routine which traverses
the whole device tree to create the job rings for the platform device.
The patch changes this to search for the compatible property of job ring
only in the child nodes i.e., the job rings are created as per the number
of children associated with the crypto node.
Signed-off-by: Nitesh Lal <NiteshNarayanLal@freescale.com>
Reviewed-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move the AES operation type and mode from async crypto context to
crypto request context. This allows for recycling of the async crypto
context for different kinds of operations.
I found this problem when I used dm-crypt, which uses the same async
crypto context (actx) for both encryption and decryption requests.
Since the requests are enqueued into the processing queue, immediatelly
storing the type of operation into async crypto context (actx) caused
corruption of this information when encryption and decryption operations
followed imediatelly one after the other. When the first operation was
dequeued, the second operation was already enqueued and overwritten the
type of operation in actx, thus causing incorrect result of the first
operation.
Fix this problem by storing the type of operation into the crypto request
context.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Updates of SoC-near drivers and other driver updates that makes more sense to
take through our tree.
The largest part of this is a conversion of device registration for some
renesas shmobile/sh devices over to use resources. This has required
coordination with the corresponding arch/sh changes, and we've agreed
to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure firmware,
which is what is used on many of the commercial Nvidia Tegra products
that are in the market, including the Nvidia Shield. The code is local
to arch/arm at this time since it's uncertain whether it will be shared
with arm64 longer-term, if needed we will refactor later.
A couple of new RTC drivers used on ARM boards, merged through our tree
on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JJlw
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree.
The largest part of this is a conversion of device registration for
some renesas shmobile/sh devices over to use resources. This has
required coordination with the corresponding arch/sh changes, and
we've agreed to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure
firmware, which is what is used on many of the commercial Nvidia Tegra
products that are in the market, including the Nvidia Shield. The
code is local to arch/arm at this time since it's uncertain whether it
will be shared with arm64 longer-term, if needed we will refactor
later.
A couple of new RTC drivers used on ARM boards, merged through our
tree on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
watchdog: davinci: rename platform driver to davinci-wdt
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
...
Fixes the following sparse warning:
drivers/crypto/mxs-dcp.c:103:1: warning:
symbol 'global_mutex' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The CCP cannot be hot-plugged so it will either be there
or it won't. Do not allow the driver to stay loaded if the
CCP does not successfully initialize.
Provide stub routines in the ccp.h file that return -ENODEV
if the CCP has not been configured in the build.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cleanup the ahash digest invocations to check the init
return code and make use of the finup routine.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When performing a hash operation if the amount of data buffered and a
request at or near the maximum data length is received then the length
calcuation could wrap causing an error in executing the hash operation.
Fix this by using a u64 type for the input and output data lengths in
all CCP operations.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For a hash operation, the caller doesn't have to supply a result
area on every call so don't use it / update it if it hasn't
been supplied.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cleanup up the usage of scatterlists to make the code cleaner
and avoid extra memory allocations when not needed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix some memory allocations to use the appropriate gfp_t type based
on the CRYPTO_TFM_REQ_MAY_SLEEP flag.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The order in the Makefile was a mess, sort it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for the MXS DCP block. The driver currently supports
SHA-1/SHA-256 hashing and AES-128 CBC/ECB modes. The non-standard
CRC32 is not yet supported.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove the old DCP driver as it had multiple severe issues. The driver
will be replaced by a more robust implementation. Here is a short list
of problems with this driver:
1) It only supports AES_CBC
2) The driver was apparently never ran behind anyone working with MXS. ie.:
-> Restarting the DCP block is not done via mxs_reset_block()
-> The DT name is not "fsl,dcp" or "fsl,mxs-dcp" as other MXS drivers
3) Introduces new ad-hoc IOCTLs
4) The IRQ handler can't use usual completion() in the driver because that'd
trigger "scheduling while atomic" oops, yes?
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
---------------------------
This pull request contains updates
to DaVinci GPIO driver and the
resultant platform code changes. The
updates include DT-conversion and
changes to make the driver cross-platform
ready.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=DxLt
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.14/gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers
From Sekhar Nori:
DaVinci GPIO driver updates
---------------------------
This pull request contains updates to DaVinci GPIO driver and the
resultant platform code changes. The updates include DT-conversion and
changes to make the driver cross-platform ready.
* tag 'davinci-for-v3.14/gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
Signed-off-by: Olof Johansson <olof@lixom.net>
drivers/crypto/ixp4xx_crypto.c: In function 'ixp_module_init':
drivers/crypto/ixp4xx_crypto.c:1419:2: error: 'dev' undeclared (first use in this function)
Now builds. Not tested on real hw.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Driver core sets it to NULL upon probe failure or release.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Driver core sets it to NULL upon probe failure or release.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Driver core sets it to NULL upon probe failure or release.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
- add DT to sha/des/aes existing drivers
- add DMA DT
- all documentation added to crypto/atmel-crypto.txt file
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSqfkKAAoJEAf03oE53VmQpHoH/2OnDX5C3hqXXL1r3p6JjRLP
B2xDO2iZcB340HrobInN0FONXVCA2b8yNy2G+U421sNjklivT4o9+66tiwBBQlbS
uoYU95CgeBs5dU1iM8Z5cIRFphEZdKDAJDd0RABUEcVPa+w569nyi5V29rwzH0UZ
hnW0IzUtJqo9344dfBai9cRcVOjrJHfiqB+05PUWb12KFbLaQhqQLL1Z5b0XasB/
9htaMxuXMXhflP7m+JY0+uVlFTOJliY9zUMN/bOqT2VBrl2tt1xLW7nooM57dB3y
+wK1A+mhYHQgEgVm1U6X3+LUluitwyA+yw2Ybf6Yi/T+3tzMjeiknfHfUB5afMY=
=JTE6
-----END PGP SIGNATURE-----
Merge tag 'at91-drivers' of git://github.com/at91linux/linux-at91 into next/drivers
From Nicolas Ferre:
AT91 crypto drivers DT support:
- add DT to sha/des/aes existing drivers
- add DMA DT
- all documentation added to crypto/atmel-crypto.txt file
* tag 'at91-drivers' of git://github.com/at91linux/linux-at91:
crypto: atmel-sha - add sha information to the log
crypto: atmel-sha - add support for Device Tree
crypto: atmel-tdes - add support for Device Tree
crypto: atmel-aes - add support for Device Tree
Signed-off-by: Olof Johansson <olof@lixom.net>
Use the common helper function crypto_authenc_extractkeys() for key
parsing.
Also fix the key buffer overflow condition: use split key pad length
instead of authentication key length.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Command "tcrypt sec=1 mode=403" give the follwoing error for Polling
mode:
root@am335x-evm:/# insmod tcrypt.ko sec=1 mode=403
[...]
[ 346.982754] test 15 ( 4096 byte blocks, 1024 bytes per update, 4 updates): 4352 opers/sec, 17825792 bytes/sec
[ 347.992661] test 16 ( 4096 byte blocks, 4096 bytes per update, 1 updates): 7095 opers/sec, 29061120 bytes/sec
[ 349.002667] test 17 ( 8192 byte blocks, 16 bytes per update, 512 updates):
[ 349.010882] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 349.020037] pgd = ddeac000
[ 349.022884] [00000000] *pgd=9dcb4831, *pte=00000000, *ppte=00000000
[ 349.029816] Internal error: Oops: 17 [#1] PREEMPT SMP ARM
[ 349.035482] Modules linked in: tcrypt(+)
[ 349.039617] CPU: 0 PID: 1473 Comm: insmod Not tainted 3.12.4-01566-g6279006-dirty #38
[ 349.047832] task: dda91540 ti: ddcd2000 task.ti: ddcd2000
[ 349.053517] PC is at omap_sham_xmit_dma+0x6c/0x238
[ 349.058544] LR is at omap_sham_xmit_dma+0x38/0x238
[ 349.063570] pc : [<c04eb7cc>] lr : [<c04eb798>] psr: 20000013
[ 349.063570] sp : ddcd3c78 ip : 00000000 fp : 9d8980b8
[ 349.075610] r10: 00000000 r9 : 00000000 r8 : 00000000
[ 349.081090] r7 : 00001000 r6 : dd898000 r5 : 00000040 r4 : ddb10550
[ 349.087935] r3 : 00000004 r2 : 00000010 r1 : 53100080 r0 : 00000000
[ 349.094783] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 349.102268] Control: 10c5387d Table: 9deac019 DAC: 00000015
[ 349.108294] Process insmod (pid: 1473, stack limit = 0xddcd2248)
[...]
This is because polling_mode is not enabled for ctx without FLAGS_FINUP.
For polling mode the bufcnt is made 0 unconditionally. But it should be made 0
only if it is a final update or a total is not zero(This condition is similar
to what is done in DMA case). Because of this wrong hashes are produced.
Fixing the same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove the pr_err calls that are issued during parameter
checking in some AES operations. This will eliminate the
possibility of filling up syslog through these paths.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Update the Kconfig to include PCI on the 'depends on'
and add 'select HW_RANDOM' to insure the necessary PCI
and HW_RANDOM functions are available/included in the
build.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The sha initialization data generated the following sparse warnings:
sparse: incorrect type in initializer (different base types)
expected unsigned int
got restricted __be32 [usertype] <noident>
Change the initialization data type from u32 to __be32.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Depending on peripheral capabilities, print SHA information at the end
of the probe function.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for Device Tree and use of the DMA DT API to
get the channels if needed.
Documentation is added for these DT nodes.
Initial code by: Nicolas Royer and Eukrea.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for Device Tree and use of the DMA DT API to
get the channels if needed.
Documentation is added for these DT nodes.
Initial code by: Nicolas Royer and Eukrea.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for Device Tree and use of the DMA DT API to
get the needed channels.
Documentation is added for these DT nodes.
Initial code by: Nicolas Royer and Eukrea.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
The AES driver currently assumes that pm_runtime_get_sync will always
succeed, which may not always be true, so add error handling for the
same.
This scenario was reported in the following bug:
place. https://bugzilla.kernel.org/show_bug.cgi?id=66441
Reported-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit 3e721aeb3d
("crypto: talitos - handle descriptor not found in error path")
tried to address the fact that CDPR (Current Descriptor Pointer Register)
is unreliable.
As it turns out, there are still issues in the function detecting the
offending descriptor:
-only 32 bits of the descriptor address are read, however the address is
36-bit - since reset_channel() initializes channels with EAE (extended
address) bit set
-reading CDPR can return zero in cur_desc; when searching the channel
fifo for this address, cur_desc == dma_desc (= 0) case might happen,
leading to an oops when trying to return desc->hdr (desc is zero)
-read channel's .tail only once; the tail is a moving target; use a
local variable for the end of search condition
Signed-off-by: Lei Xu <Lei.Xu@freescale.com>
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Tested-by: Kalyani Chowdhury <Kalyani.Chowdhury@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In omap_sham_probe() and omap_sham_remove(), 'dd->dma_lch'
is released without checking to see if it was successfully
requested or not. This is a bug and was identified and
reported by Dan Carpenter here:
http://www.spinics.net/lists/devicetree/msg11023.html
Add code to only release 'dd->dma_lch' when its not NULL
(that is, when it was successfully requested).
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
CC: Joel Fernandes <joelf@ti.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These files provide the ability to configure and build the
AMD CCP device driver and crypto API support.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These routines provide crypto API support for SHA1, SHA224 and SHA256
on the AMD CCP. HMAC support for these SHA modes is also provided.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These routines provide crypto API support for the XTS-AES mode of AES
on the AMD CCP.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These routines provide crypto API support for the CMAC mode of AES
on the AMD CCP.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These routines provide crypto API support for AES on the AMD CCP.
Support for AES modes: ECB, CBC, OFB, CFB and CTR
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These routines provide the support for the interface between the crypto API
and the AMD CCP. This includes insuring that requests associated with a
given tfm on the same cpu are processed in the order received.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These routines provide the device driver support for the AMD
Cryptographic Coprocessor (CCP).
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
talitos does not handle well zero-length assoc data. From dmesg:
talitos ffe30000.crypto: master data transfer error
talitos ffe30000.crypto: gather return/length error
Check whether assoc data is provided by inspecting assoclen,
not assoc pointer.
This is needed in order to pass testmgr tests.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
linuxnext currently doesn't compile with the powerpc mpc85xx_defconfig
giving:
drivers/crypto/caam/jr.c: In function 'caam_jr_probe':
drivers/crypto/caam/jr.c:468:2: error: implicit declaration of function 'of_iomap' [-Werror=implicit-function-declaration]
In:
commit 313ea293e9
Author: Ruchika Gupta <ruchika.gupta@freescale.com>
crypto: caam - Add Platform driver for Job Ring
We added a reference to of_iomap but did add the necessary include file.
The below adds this include.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto update from Herbert Xu:
- Made x86 ablk_helper generic for ARM
- Phase out chainiv in favour of eseqiv (affects IPsec)
- Fixed aes-cbc IV corruption on s390
- Added constant-time crypto_memneq which replaces memcmp
- Fixed aes-ctr in omap-aes
- Added OMAP3 ROM RNG support
- Add PRNG support for MSM SoC's
- Add and use Job Ring API in caam
- Misc fixes
[ NOTE! This pull request was sent within the merge window, but Herbert
has some questionable email sending setup that makes him public enemy
#1 as far as gmail is concerned. So most of his emails seem to be
trapped by gmail as spam, resulting in me not seeing them. - Linus ]
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (49 commits)
crypto: s390 - Fix aes-cbc IV corruption
crypto: omap-aes - Fix CTR mode counter length
crypto: omap-sham - Add missing modalias
padata: make the sequence counter an atomic_t
crypto: caam - Modify the interface layers to use JR API's
crypto: caam - Add API's to allocate/free Job Rings
crypto: caam - Add Platform driver for Job Ring
hwrng: msm - Add PRNG support for MSM SoC's
ARM: DT: msm: Add Qualcomm's PRNG driver binding document
crypto: skcipher - Use eseqiv even on UP machines
crypto: talitos - Simplify key parsing
crypto: picoxcell - Simplify and harden key parsing
crypto: ixp4xx - Simplify and harden key parsing
crypto: authencesn - Simplify key parsing
crypto: authenc - Export key parsing helper function
crypto: mv_cesa: remove deprecated IRQF_DISABLED
hwrng: OMAP3 ROM Random Number Generator support
crypto: sha256_ssse3 - also test for BMI2
crypto: mv_cesa - Remove redundant of_match_ptr
crypto: sahara - Remove redundant of_match_ptr
...
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
Commit b5b4bb3f6a (of: only include prom.h on sparc) removed implicit
includes of of_*.h headers by powerpc's prom.h. Some components were
missed in initial clean-up patch, so add the necessary includes to fix
powerpc builds.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-ide@vger.kernel.org
Cc: linux-crypto@vger.kernel.org
Don't statically allocate struct device's in modules, and shut the
warning up with an empty release() function. There's a reason that
warning is there and that's not for people to hide in this way. It's
there to persuade people to use the correct APIs to allocate platform
devices.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
NIST vectors for CTR mode in testmgr.h assume the entire IV as the counter. To
get correct results that match the output of these vectors, we need to set the
counter length correctly.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
- Earlier interface layers - caamalg, caamhash, caamrng were
directly using the Controller driver private structure to access
the Job ring.
- Changed the above to use alloc/free API's provided by Job Ring Drive
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: Garg Vakul-B16394 <vakul@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
With each of the Job Ring available as a platform device, the
Job Ring driver needs to take care of allocation/deallocation
of the Job Rings to the above interface layers. Added APIs
in Job Ring Driver to allocate/free Job rings
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: Garg Vakul-B16394 <vakul@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The SEC Job Rings are now available as individual devices.
This would enable sharing of job rings between kernel and
user space. Job Rings can now be dynamically bound/unbound
from kernel.
Changes are made in the following layers of CAAM Driver
1. Controller driver
- Does basic initialization of CAAM Block.
- Creates platform devices for Job Rings.
(Earlier the initialization of Job ring was done
by the controller driver)
2. JobRing Platform driver
- Manages the platform Job Ring devices created
by the controller driver
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: Garg Vakul-B16394 <vakul@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Replace some instances of of_irq_map_one()/irq_create_of_mapping() and
of_irq_to_resource() by the simpler equivalent irq_of_parse_and_map().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
[grant.likely: resolved conflicts with core code renames]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Use the common helper function crypto_authenc_extractkeys() for key
parsing.
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Mathias Krause <mathias.krause@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the common helper function crypto_authenc_extractkeys() for key
parsing. Also ensure the auth key won't overflow the hash_ctx buffer.
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Mathias Krause <mathias.krause@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the common helper function crypto_authenc_extractkeys() for key
parsing. Also ensure the keys do fit into the corresponding buffers.
Otherwise memory corruption might occur.
Cc: Christian Hohnstaedt <chohnstaedt@innominate.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Mathias Krause <mathias.krause@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
devm_ioremap_resource() may fail, so better check its return value and propagate
it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
tasklet_kill() is not being called in probe and the remove function releases
the resources in the wrong order.
Fix these issues.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Using Use devm_request_irq() can make the code smaller and simpler, as we do
not need to call free_irq() in the probe error path and in the remove function.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Using devm_ioremap_resource() can make the code simpler and smaller.
When devm_ioremap_resource() is used there is no need to explicitely check the
error returned by platform_get_resource().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
devm_clk_get is device managed and makes code simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
'dd' is tested for NULL. However, it is derefenced in the error
message print. Change the print to pr_err to avoid this.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
'tegra_aes_cra_exit' is used only in this file.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Local symbols used only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Local symbols used only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
KMap the buffers before copying trailing bytes during hmac into a session
temporary buffer. This is required if pinned buffer from user-space is send
during hmac and is safe even if hmac request is generated from within kernel.
Signed-off-by: Yashpal Dutta <yashpal.dutta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
RNG4 block contains multiple (i.e. 2) state handles that can be
initialized. This patch adds the necessary code for detecting
which of the two state handles has been instantiated by another
piece of software e.g. u-boot and instantiate the other one (or
both if none was instantiated). Only the state handle(s)
instantiated by this driver will be deinstantiated when removing
the module.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
RNG4 defines in desc.h were incomplete (bits AI & PS were missing),
while SK was set as an ALG related bit. This patchs adds the
missing bits and corrects the SK bit.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If the caam driver module instantiates the RNG state handle 0, then
upon the removal of the module, the RNG state handle is left
initialized. This patch takes care of reverting the state of the
handle back to its previous uninstantatied state.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch splits the RNG4 state handle instantiation
function into two parts: one that handles the creation
of the descriptor which instructs the CAAM to perform
the instantiation of the state handle and another
function that performs the running of the said descriptor
using the DECO debug mechanism.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The RNG4 block in CAAM needs to be 'seeded' first before being used
for generating pseudo-random data. The 'seeding' is done by getting
entropy from the TRNG ring oscillator. The RTFRQMAX register controls
the maximum allowable number of samples that can be aquired during
an entropy sample. Depending on the clock at which the RNG4 block
(and for that matter the SEC block) runs, it's possible that a
hard-coded value for the maximum frequency is inadequate, i.e. more
samples than needed are taken. This is an error, and thus the RNG4
block doesn't get initialized. The patch attempts to alleviate
this issue by trying with progressivly larger frequencies, until
the number of samples is adequate.
This patch also fixes how a descriptor is deemed as being finished:
instead of checking the VALID field in the DECO debug register,
it makes sure that the DECO is idle, by checking the DECO state field
of the said register.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If the CAAM driver initialization failed (due to various reasons, e.g. RNG4
initialization failed), then the registration of hash/algorithms/rng shouldn't
take place. This patch adds the necessary code to prevent this registration.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The way the DECO runs a descriptor through the direct (debug)
interface is different from the JRI interface: the DECO will
continue to try and execute the next commands, after the descriptor
buffer has ended. This leads to unpredictable results and possibly
to locking up of the DECO. This patch adds a halt command at the
end of the descriptor to ensure the DECO halts when it reaches
the end of the descriptor buffer.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The way I read the Tegra AES RNG is that it has a homebrew
algorithm for initializing the 128bit RNG using timespec and
the unique chip ID. This looks like reinventing the (square)
wheel, instead just grab 128bits from the kernel entropy pool
where the time and (after another patch) chip unique ID is
already mixed in.
Incidentally this also gets rid of a rather ugly
cross-dependence on the machine using an extern declaration.
Cc: Varun Wadekar <vwadekar@nvidia.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Each call to the co-processor, with exception of the last call, needs to
send data that is multiple of block size. As consequence, any remaining
data is kept in the internal NX context.
This patch fixes a bug in the driver that causes it to save incorrect
data into the context when data is bigger than the block size.
Reviewed-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The NX CGM implementation doesn't support zero length messages and the
current implementation has two flaws:
- When the input data length is zero, it ignores the associated data.
- Even when both lengths are zero, it uses the Crypto API to encrypt a
zeroed block using ctr(aes) and because of this it allocates a new
transformation and sets the key for this new tfm. Both operations are
intended to be used only in user context, while the cryptographic
operations can be called in both user and softirq contexts.
This patch replaces the nested Crypto API use and adds two special
cases:
- When input data and associated data lengths are zero: it uses NX ECB
mode to emulate the encryption of a zeroed block using ctr(aes).
- When input data is zero and associated data is available: it uses NX
GMAC mode to calculate the associated data MAC.
Reviewed-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The NX XCBC implementation doesn't support zero length messages and
because of that NX is currently returning a hard-coded hash for zero
length messages. However this approach is incorrect since the hash value
also depends on which key is used.
This patch removes the hard-coded hash and replace it with an
implementation based on the RFC 3566 using ECB.
Reviewed-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch updates the NX driver to perform several hyper calls when necessary
so that the length limits of scatter/gather lists are respected.
Reviewed-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Fionnuala Gunter <fin@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch updates the NX driver to perform several hyper calls when necessary
so that the length limits of scatter/gather lists are respected.
Reviewed-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Reviewed-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Fionnuala Gunter <fin@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch updates the nx-aes-gcm implementation to perform several
hyper calls if needed in order to always respect the length limits for
scatter/gather lists.
Two different limits are considered:
- "ibm,max-sg-len": maximum number of bytes of each scatter/gather
list.
- "ibm,max-sync-cop":
- The total number of bytes that a scatter/gather list can hold.
- The maximum number of elements that a scatter/gather list can have.
Reviewed-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch updates the nx-aes-ctr implementation to perform several
hyper calls if needed in order to always respect the length limits for
scatter/gather lists.
Two different limits are considered:
- "ibm,max-sg-len": maximum number of bytes of each scatter/gather
list.
- "ibm,max-sync-cop":
- The total number of bytes that a scatter/gather list can hold.
- The maximum number of elements that a scatter/gather list can have.
Reviewed-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch updates the nx-aes-cbc implementation to perform several
hyper calls if needed in order to always respect the length limits for
scatter/gather lists.
Two different limits are considered:
- "ibm,max-sg-len": maximum number of bytes of each scatter/gather
list.
- "ibm,max-sync-cop":
- The total number of bytes that a scatter/gather list can hold.
- The maximum number of elements that a scatter/gather list can have.
Reviewed-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch updates the nx-aes-ecb implementation to perform several
hyper calls if needed in order to always respect the length limits for
scatter/gather lists.
Two different limits are considered:
- "ibm,max-sg-len": maximum number of bytes of each scatter/gather
list.
- "ibm,max-sync-cop":
- The total number of bytes that a scatter/gather list can hold.
- The maximum number of elements that a scatter/gather list can have.
Reviewed-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch includes one more parameter to nx_build_sg_lists() to skip
the given number of bytes from beginning of each sg list.
This is needed in order to implement the fixes for the AES modes to make
them able to process larger chunks of data.
Reviewed-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Each cycle of SHA512 operates on 32 data words where as
SHA256 operates on 16 data words. This needs to be updated
while configuring DMA channels. Doing the same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For writing input buffer into DATA_IN register current driver
has the following state machine:
-> if input buffer < 9 : use fallback driver
-> else if input buffer < block size : Copy input buffer into data_in regs
-> else use dma transfer.
In cases where requesting for DMA channels fails for some reason,
or channel numbers are not provided in DT or platform data, probe
also fails. Instead of returning from driver use cpu polling mode.
In this mode processor polls on INPUT_READY bit and writes data into
data_in regs when it equals 1. This operation is repeated until the
length of message.
Now the state machine looks like:
-> if input buffer < 9 : use fallback driver
-> else if input buffer < block size : Copy input buffer into data_in regs
-> else if dma enabled: use dma transfer
else use cpu polling mode.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The bug here is that:
while (eng_busy & (!icq_empty) & dma_busy)
is never true because it's using bitwise instead of logical ANDs. The
other bitwise AND conditions work as intended but I changed them as well
for consistency.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is a typo here. "dev->hw_link[]" is an array, not a pointer, so
the check is nonsense. We should be checking recently allocated
"dev->hw_link[0]" instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For AM437x SoC, ARCH_OMAP2 and ARCH_OMAP3 is not enabled in the defconfig. We
follow same thing as SHA driver, and add depends on ARCH_OMAP2PLUS so that the
config is selectable for AES driver on AM437x SoC builds.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_kzalloc instead of kzalloc. With this change, there is no need to
call kfree in error/exit paths.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For cases where offset/length of on any page of the input SG is not aligned by
AES_BLOCK_SIZE, we copy all the pages from the input SG list into a contiguous
buffer and prepare a single element SG list for this buffer with length as the
total bytes to crypt.
This is requried for cases such as when an SG list of 16 bytes total size
contains 16 pages each containing 1 byte. DMA using the direct buffers of such
instances is not possible.
For this purpose, we first detect if the unaligned case and accordingly
allocate enough number of pages to satisfy the request and prepare SG lists.
We then copy data into the buffer, and copy data out of it on completion.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In cases where requesting for DMA channels fails for some reason, or channel
numbers are not provided in DT or platform data, we switch to PIO-only mode
also checking if platform provides IRQ numbers and interrupt register offsets
in DT and platform data. All dma-only paths are avoided in this mode.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We initialize the scatter gather walk lists needed for PIO mode and avoid all
DMA paths such as mapping/unmapping buffers by checking for the pio_only flag.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We add an IRQ handler that implements a state-machine for PIO-mode and data
structures for walking the scatter-gather list. The IRQ handler is called in
succession both when data is available to read or next data can be sent for
processing. This process continues till the entire in/out SG lists have been
walked. Once the SG-list has been completely walked, the IRQ handler schedules
the done_task tasklet.
Also add a useful macro that is used through out the IRQ code for a common
pattern of calculating how much an SG list has been walked. This improves code
readability and avoids checkpatch errors.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add IRQ information to pdata and helper macros. These are required
for PIO-mode support.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Intermdiate buffers were allocated, mapped and used for DMA. These are no
longer required as we use the SGs from crypto layer directly in previous
commits in the series. Also along with it, remove the logic for copying SGs
etc as they are no longer used, and all the associated variables in omap_aes_device.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Earlier functions that did a similar sync are replaced by the dma_sync_sg_*
which can operate on entire SG list.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In early version of this driver, assumptions were made such as DMA layer
requires contiguous buffers etc. Due to this, new buffers were allocated,
mapped and used for DMA. These assumptions are no longer true and DMAEngine
scatter-gather DMA doesn't have such requirements. We simply the DMA operations
by directly using the scatter-gather buffers provided by the crypto layer
instead of creating our own.
Lot of logic that handled DMA'ing only X number of bytes of the total, or as
much as fitted into a 3rd party buffer is removed and is no longer required.
Also, good performance improvement of atleast ~20% seen with encrypting a
buffer size of 8K (1800 ops/sec vs 1400 ops/sec). Improvement will be higher
for much larger blocks though such benchmarking is left as an exercise for the
reader. Also DMA usage is much more simplified and coherent with rest of the
code.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Crypto layer only passes nbytes but number of SG elements is needed for mapping
or unmapping SGs at one time using dma_map* API and also needed to pass in for
dmaengine prep function.
We call function added to scatterwalk for this purpose in omap_aes_handle_queue
to populate the values which are used later.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When DEBUG is enabled, these macros can be used to print variables in integer
and hex format, and clearly display which registers, offsets and values are
being read/written , including printing the names of the offsets and their values.
Using statement expression macros in read path as,
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch fixes a bug in the nx-aes-gcm implementation.
Corrected the code so that the authtag is always verified after
decrypting and not just when there is associated data included.
Also, corrected the code to retrieve the input authtag from src
instead of dst.
Reviewed-by: Fionnuala Gunter <fin@linux.vnet.ibm.com>
Reviewed-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds an option to the Kconfig file for
SEC which enables the user to see the debug messages
that are printed inside the SEC driver.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CAAM driver contains one macro (xstr) used for printing
the line location in a file where a memdump is done. This patch
replaces the xstr macro with the already existing __stringify
macro that performs the same function.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The NX driver uses the transformation context to store several fields
containing data related to the state of the operations in progress.
Since a single tfm can be used by different kernel threads at the same
time, we need to protect the data stored into the context.
This patch makes use of spin locks to protect the data where a race
condition can happen.
Reviewed-by: Fionnuala Gunter <fin@linux.vnet.ibm.com>
Reviewed-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These local symbols are used only in this file.
Fix the following sparse warnings:
drivers/crypto/amcc/crypto4xx_alg.c:35:6: warning: symbol 'set_dynamic_sa_command_0' was not declared. Should it be static?
drivers/crypto/amcc/crypto4xx_alg.c:55:6: warning: symbol 'set_dynamic_sa_command_1' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This local symbol is used only in this file.
Fix the following sparse warnings:
drivers/crypto/sahara.c:420:6: warning: symbol 'sahara_watchdog' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch fixes a bug that is triggered when cts(cbc(aes)) is used with
nx-crypto driver on input larger than 32 bytes.
The chaining value from co-processor was not being saved. This value is
needed because it is used as the IV by cts(cbc(aes)).
Signed-off-by: Fionnuala Gunter <fin@linux.vnet.ibm.com>
Reviewed-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The co-processor has several limits regarding the length of
scatter/gather lists and the total number of bytes in it. These limits
are available in the device tree, as following:
- "ibm,max-sg-len": maximum number of bytes of each scatter/gather
list.
- "ibm,max-sync-cop": used for synchronous operations, it is an array
of structures that contains information regarding the limits that
must be considered for each mode and operation. The most important
limits in it are:
- The total number of bytes that a scatter/gather list can hold.
- The maximum number of elements that a scatter/gather list can
have.
This patch updates the NX driver to perform several hyper calls if
needed in order to always respect the length limits for scatter/gather
lists.
Reviewed-by: Fionnuala Gunter <fin@linux.vnet.ibm.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The co-processor receives data to be hashed through scatter/gather lists
pointing to physical addresses. When a vmalloc'ed data is given, the
driver must calculate the physical address to each page of the data.
However the current version of it just calculates the physical address
once and keeps incrementing it even when a page boundary is crossed.
This patch fixes this behaviour.
Reviewed-by: Fionnuala Gunter <fin@linux.vnet.ibm.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Signed-off-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_kzalloc() to make cleanup paths simpler.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Using devm_request_irq() rather than request_irq().
So removing free_irq() calls from the probe error
path and the remove handler.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for the OMAP5 version of the SHAM module
that is present on OMAP5 and AM43xx SoCs.
This module is very simialar to OMAP4 version of SHAM module,
and adds SHA384 SHA512 hardware-accelerated hash functions to it.
To handle the higher digest size of SHA512, few SHA512_DIGEST_i
(i=1-16, and first 8 registers are duplicated from SHA_DIGEST_i
registers) registers are added at the end of register set.
So adding the above register offsets and module info in pdata.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Adding support for SHA348 and SHA512 in addition to MD5, SHA1, SHA224
SHA256 that the omap sha module supports.
In order to add the support
- Removed hard coded register offsets and passing offsets from pdata
- Updating Flag offsets so that they can be used for SHA256 and SHA512
- Adding the algo info.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Logging messages without newlines are possibly interleaved
with other messages. Add terminating newlines to avoid
this.
Other miscellaneous changes:
Make arrays const to reduce data size
Add pr_fmt to prefix pr_<level>, remove now unused DEV_DBG_NAME
Coalesce formats, align arguments
Remove unnecessary OOM messages as dump_stack is already done
Remove unnecessary cast of void *
Change kzalloc(sizeof(struct)...) to kzalloc(sizeof(*var), ...)
Reduce indents in struct definitions
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove the dependency of RNG instantiation on Job Ring. Now
RNG instantiation for devices with RNG version > 4 is done
by directly programming DECO 0.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto fixes from Herbert Xu:
"This push fixes a memory corruption issue in caam, as well as
reverting the new optimised crct10dif implementation as it breaks boot
on initrd systems.
Hopefully crct10dif will be reinstated once the supporting code is
added so that it doesn't break boot"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
Revert "crypto: crct10dif - Wrap crc_t10dif function all to use crypto transform framework"
crypto: caam - Fixed the memory out of bound overwrite issue
DESC_JOB_IO_LEN is a generic macro which indicates the space required in
the descriptor for placing SEQIN/OUT commands, job descriptor header,
shared descriptor pointer. Moving it to descriptor construction file
which can be supposedly included by different algo offload files.
Change-Id: Ic8900990d465e9079827b0c7fcacc61766d7efb6
Signed-off-by: Vakul Garg <vakul@freescale.com>
Reviewed-by: Geanta Neag Horia Ioan-B05471 <horia.geanta@freescale.com>
Reviewed-by: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
Tested-by: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use sg_pcopy_to_buffer() which is better than the function previously used.
Because it doesn't do kmap/kunmap for skipped pages.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to
have these changes merged through arm-soc. As we proceed to untangle
the dependencies between platform code and driver code, the amount of
changes in this category is fortunately shrinking, for 3.11 we have
16 branches here and 101 non-merge changesets, the majority of which
are for the stedma40 dma engine driver used in the ux500 platform.
Cleaning up that code touches multiple subsystems, but gets rid
of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox
is an intermediate step and is still omap specific at the moment.
Patches exist to generalize the subsystem and add other drivers
with the same API, but those did not make it for 3.11.
Conflicts:
* In cpu-db8500.c results from the removal of the u8500_of_init_devices
function in combination with the split of u8500_auxdata_lookup.
* In arch/arm/mach-omap2/devices.c, the includes got reshuffled.
we need to keep linux/wl12xx.h and linux/platform_data/mailbox-omap.h.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=mJsI
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver specific changes from Arnd Bergmann:
"These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to have
these changes merged through arm-soc.
As we proceed to untangle the dependencies between platform code and
driver code, the amount of changes in this category is fortunately
shrinking, for 3.11 we have 16 branches here and 101 non-merge
changesets, the majority of which are for the stedma40 dma engine
driver used in the ux500 platform. Cleaning up that code touches
multiple subsystems, but gets rid of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox is an
intermediate step and is still omap specific at the moment. Patches
exist to generalize the subsystem and add other drivers with the same
API, but those did not make it for 3.11."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
crypto: ux500: use dmaengine_submit API
crypto: ux500: use dmaengine_prep_slave_sg API
crypto: ux500: use dmaengine_device_control API
crypto: ux500/crypt: add missing __iomem qualifiers
crypto: ux500/hash: add missing static qualifiers
crypto: ux500/hash: use readl on iomem addresses
dmaengine: ste_dma40: Declare memcpy config as static
ARM: ux500: Remove mop500_snowball_ethernet_clock_enable()
ARM: ux500: Correct the EN_3v3 regulator's on/off GPIO
ARM: ux500: Provide a AB8500 GPIO Device Tree node
gpio: rcar: fix gpio_rcar_of_table
gpio-rcar: Remove #ifdef CONFIG_OF around OF-specific sections
gpio-rcar: Reference core gpio documentation in the DT bindings
clk: exynos5250: Add enum entries for divider clock of i2s1 and i2s2
ARM: dts: Update Samsung I2S documentation
ARM: dts: add clock provider information for i2s controllers in Exynos5250
ARM: dts: add Exynos audio subsystem clock controller node
clk: samsung: register audio subsystem clocks using common clock framework
ARM: dts: use #include for all device trees for Samsung
pinctrl: s3c24xx: use correct header for chained_irq functions
...
- Fix various error path and sparse bugs in the DMA40 driver
- Fix various compile errors in the ux500 crypto driver
(dependent on the DMA40 changes).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=sHkJ
-----END PGP SIGNATURE-----
Merge tag 'ux500-dma40-for-arm-soc-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/drivers
From Linus Walleij:
DMA40 fixes for earlier submitted driver patches:
- Fix various error path and sparse bugs in the DMA40 driver
- Fix various compile errors in the ux500 crypto driver
(dependent on the DMA40 changes).
* tag 'ux500-dma40-for-arm-soc-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
crypto: ux500: use dmaengine_submit API
crypto: ux500: use dmaengine_prep_slave_sg API
crypto: ux500: use dmaengine_device_control API
crypto: ux500/crypt: add missing __iomem qualifiers
crypto: ux500/hash: add missing static qualifiers
crypto: ux500/hash: use readl on iomem addresses
dmaengine: ste_dma40: Declare memcpy config as static
dmaengine: ste_dma40: fix error return code in d40_probe()
Signed-off-by: Olof Johansson <olof@lixom.net>
Use dmaengine_prep_slave_sg inline function instead of going through the
structures manually.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use dmaengine_device_control inline function instead of going through the
structures manually.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* A couple of new board support, cfa10055 and cfa10057
* A few updates on cfa10036 device tree source
* Some auart pinctrl data addition
* Adopt soc bus infrastructure for mach-mxs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRvwUEAAoJEFBXWFqHsHzOZXgH/jYs9okBIb6UtYegmdGUinCD
VHJJT+RT8ceosMjBt+aBfpKplUG1X3OOoWbpU7Uv5JKNfY+0QbYTr4bdSE0YTF19
/ml5lCLLqW1MouErxIIe9yFrs4ZhZLLuW0Uy+ze7XVO/VPUlmJWYGU4D5gLcN+SH
aDdwAfe0SEydxWKp5euh6O2qPuuOro5/kUOPvYs6xaJj3marWkD9M6YyhaWvaFwF
2iUWzSd6dGabHRYwG2r38IlKMo6xncnu3b1NPifVMiPtiHFJ8t0SyTEGmpq19G+x
G6q0TneOUVIgH0PN4YQoCGOR6oAB52Z/dVTVlGx6LE6w9Q95wI3XNHltP5U+bF0=
=Oeyn
-----END PGP SIGNATURE-----
Merge tag 'mxs-dt-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo:
mxs device tree changes for 3.11:
* A couple of new board support, cfa10055 and cfa10057
* A few updates on cfa10036 device tree source
* Some auart pinctrl data addition
* Adopt soc bus infrastructure for mach-mxs
* tag 'mxs-dt-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: dt: Add Crystalfontz CFA-10057 device tree
ARM: mxs: dt: Add the Crystalfontz CFA-10055 device tree
ARM: cfa10049: Switch the chip select pin of the LCD controller
ARM: cfa10036: Add USB0 OTG port
ARM: dts: apf28dev: Add touchscreen support for APF28dev
ARM: mxs: Fix UARTs on M28EVK
ARM: cfa10036: dt: Change i2c0 clock frequency
ARM: dts: cfa10036: Change the OLED display to SSD1306
ARM: mx28: add auart4 2 pins pinmux to imx28.dtsi
ARM: mx28: add auart3 2 pins pinmux to imx28.dtsi
ARM: mx28: add auart2 2 pins pinmux to imx28.dtsi
ARM: mxs: Use soc bus infrastructure
ARM: dts: mx28: Adjust the digctl compatible string
ARM: mxs: Remove init_irq declaration in machine description
Includes an update to 3.10-rc6
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix for the thermal node to be contained in the PRCMU node
- Add the DTS and auxdata needed to boot the U8540 platform
- Various regulators added and renamed
- Rename base SoC node
- A bunch of DMA patches adding channels for DT boots
- A bunch of crypto+hash patches adding config for DT boots
- A bunch of patches fixing the ALSA SoC support to work
- Register the LP5521 LEDs
- Fix a number of typos and naming errors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=cph0
-----END PGP SIGNATURE-----
Merge tag 'ux500-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From Linus Walleij:
Device tree patches for ux500, basically trees and auxdata:
- Fix for the thermal node to be contained in the PRCMU node
- Add the DTS and auxdata needed to boot the U8540 platform
- Various regulators added and renamed
- Rename base SoC node
- A bunch of DMA patches adding channels for DT boots
- A bunch of crypto+hash patches adding config for DT boots
- A bunch of patches fixing the ALSA SoC support to work
- Register the LP5521 LEDs
- Fix a number of typos and naming errors
* tag 'ux500-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (39 commits)
ARM: ux500: drop any 0x prefix from I2C DT devices
ARM: ux500: Allocate correct amount of memory for the u8540 in DT
ARM: ux500: Provide auxdata to ux500 ASoC driver
ARM: ux500: Add DT regulators for ab8500-codec
ARM: ux500: Correct anamic2 typo in DT files
ARM: ux500: Fix trivial typo in v-anamic1 comment
ARM: ux500: Reduce PRCMU reg-names to shorter form for u8540 DT
ARM: ux500: Add an auxdata entry for MUSB for clock-name look-up
ARM: ux500: cut chip-select GPIOs from SSP device
ARM: ux500: use symbolic names for interrupt flags
ARM: ux500: use #include syntax to include *.dtsi.
ARM: ux500: bump MMC/SD max frequency for DT boots
ARM: ux500: Apply other compatible name to the u8540 DTS file
pinctrl/nomadik: Standardise Pinctrl compat string for DBx5x based platforms
ARM: ux500: Standardise Pinctrl compatible string for DBx5x based platforms
ARM: ux500: Standardise DBx5x0 based Pinctrl compat string in the DTS
crypto: ux500/hash - Enable DT probing of the driver
crypto: ux500/cryp - Enable DT probing of the driver
ARM: ux500: enable the crypto and hash on all dbx500
ARM: ux500: Provide an AUXDATA entry for ux500-hash
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull crypto fixes from Herbert Xu:
"This fixes a build problem in sahara and temporarily disables two new
optimisations because of performance regressions until a permanent fix
is ready"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: sahara - fix building as module
crypto: blowfish - disable AVX2 implementation
crypto: twofish - disable AVX2 implementation
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These symbols are referenced only in this file and hence
should be static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Tested-by: Tobias Rauter <tobiasrauter@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tadeusz Struk