Instead of casing u32 values to u64 it makes more sense to just start out
with u64 values in the first place. This way we don't need to create a
mess with all of the casts needed to populate a 64b value.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e and i40evf drivers contained code for inserting an outer checksum
on UDP tunnels. The issue however is that the upper levels of the stack
never requested such an offload and it results in possible errors.
In addition the same logic was being applied to the Rx side where it was
attempting to validate the outer checksum, but the logic there was
incorrect in that it was testing for the resultant sum to be equal to the
header checksum instead of being equal to 0.
Since this code is so massively flawed, and doing things that we didn't ask
for it to do I am just dropping it, and will bring it back later to use as
an offload for SKB_GSO_UDP_TUNNEL_CSUM which can make use of such a
feature.
As far as the Rx feature I am dropping it completely since it would need to
be massively expanded and applied to IPv4 and IPv6 checksums for all parts,
not just the one that supports Tx checksum offload for the outer.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Florian Westphal says:
====================
netlink: remove mmapped netlink support
As discussed during netconf 2016 in Seville, this series removes
CONFIG_NETLINK_MMAP.
Close to three years after it was merged it has retained several problems
that do not appear to be fixable.
No official netfilter libmnl release contains support for mmap backed netlink
sockets. No openvswitch release makes use of it either.
To use the mmap interface, userspace not only has to probe for mmap netlink
support, it also has to implement a recv/socket receive path in order to
handle messages that exceed the size of an rx ring element (NL_MMAP_STATUS_COPY).
So if there are odd programs out there that attempt to use MMAP netlink
they should continue to work as they already need a socket based code path
to work properly.
The actual revert (first patch) has a list of problems.
The followup patches remove a couple of helpers that are no longer needed
after the revert.
I did a few tests with mmap vs. socket based interface on a 4.4 based
kernel on an i7-4790 box and there are no performance advantages:
loopback, single nfqueue, queueing in -t filter INPUT:
traffic generated by 8 * ping -q -f localhost:
socket backend:
real 0m27.325s
user 0m3.993s
sys 0m23.292s
with mmap ring backend:
real 0m29.054s
user 0m4.924s
sys 0m24.127s
with single tcp stream, unidirectional, loopback mtu set at 1500
(nc localhost discard < /dev/zero > /dev/null):
socket interface:
time nfqdump -b $((8 * 1024 * 1024 * 1024)) -w /dev/null
real 0m15.960s
user 0m1.756s
sys 0m11.143s
mmap ring:
real 0m16.441s
user 0m3.040s
sys 0m13.687s
socket interface nfqdump[1] with --gso option (i.e. MTU is exceeded,
no kernel-side segmentation and checksum fixups) completes in about 5s.
I also tested dumping a conntrack table with 1m entries.
On my box this takes about 2.4 seconds for both mmap and socket backend:
time LD_PRELOAD=../../src/.libs/libmnl.so ./nfct-dump-sk > /dev/null
mnl_cb_run: Success
messages: 1000000
real 0m2.485s
user 0m1.085s
sys 0m1.400s
time LD_PRELOAD=../../src/.libs/libmnl.so ./nfct-dump-mmap > /dev/null
messages: 1000000
real 0m2.451s
user 0m1.124s
sys 0m1.328s
[1] https://git.breakpoint.cc/cgit/fw/nfqdump.git/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
reverts commit 3ab1f683bf ("nfnetlink: add support for memory mapped
netlink")'
Like previous commits in the series, remove wrappers that are not needed
after mmapped netlink removal.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following mmapped netlink removal this code can be simplified by
removing the alloc wrapper.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit bb9b18fb55 ("genl: Add genlmsg_new_unicast() for
unicast message allocation")'.
Nothing wrong with it; its no longer needed since this was only for
mmapped netlink support.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
revert commit 795449d8b8 ("openvswitch: Enable memory mapped Netlink i/o").
Following the mmaped netlink removal this code can be removed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
mmapped netlink has a number of unresolved issues:
- TX zerocopy support had to be disabled more than a year ago via
commit 4682a03586 ("netlink: Always copy on mmap TX.")
because the content of the mmapped area can change after netlink
attribute validation but before message processing.
- RX support was implemented mainly to speed up nfqueue dumping packet
payload to userspace. However, since commit ae08ce0021
("netfilter: nfnetlink_queue: zero copy support") we avoid one copy
with the socket-based interface too (via the skb_zerocopy helper).
The other problem is that skbs attached to mmaped netlink socket
behave different from normal skbs:
- they don't have a shinfo area, so all functions that use skb_shinfo()
(e.g. skb_clone) cannot be used.
- reserving headroom prevents userspace from seeing the content as
it expects message to start at skb->head.
See for instance
commit aa3a022094 ("netlink: not trim skb for mmaped socket when dump").
- skbs handed e.g. to netlink_ack must have non-NULL skb->sk, else we
crash because it needs the sk to check if a tx ring is attached.
Also not obvious, leads to non-intuitive bug fixes such as 7c7bdf359
("netfilter: nfnetlink: use original skbuff when acking batches").
mmaped netlink also didn't play nicely with the skb_zerocopy helper
used by nfqueue and openvswitch. Daniel Borkmann fixed this via
commit 6bb0fef489 ("netlink, mmap: fix edge-case leakages in nf queue
zero-copy")' but at the cost of also needing to provide remaining
length to the allocation function.
nfqueue also has problems when used with mmaped rx netlink:
- mmaped netlink doesn't allow use of nfqueue batch verdict messages.
Problem is that in the mmap case, the allocation time also determines
the ordering in which the frame will be seen by userspace (A
allocating before B means that A is located in earlier ring slot,
but this also means that B might get a lower sequence number then A
since seqno is decided later. To fix this we would need to extend the
spinlocked region to also cover the allocation and message setup which
isn't desirable.
- nfqueue can now be configured to queue large (GSO) skbs to userspace.
Queing GSO packets is faster than having to force a software segmentation
in the kernel, so this is a desirable option. However, with a mmap based
ring one has to use 64kb per ring slot element, else mmap has to fall back
to the socket path (NL_MMAP_STATUS_COPY) for all large packets.
To use the mmap interface, userspace not only has to probe for mmap netlink
support, it also has to implement a recv/socket receive path in order to
handle messages that exceed the size of an rx ring element.
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Ken-ichirou MATSUZAWA <chamaken@gmail.com>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VLANs are created / destroyed on a VLAN filtering bridge (MASTER
flag set), the configuration is passed down to the hardware. However,
when only the flags (e.g. PVID) are toggled, the configuration is done
in the software bridge alone.
While it is possible to pass these flags to hardware when invoked with
the SELF flag set, this creates inconsistency with regards to the way
the VLANs are initially configured.
Pass the flags down to the hardware even when the VLAN already exists
and only the flags are toggled.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to select SGMII-to-copper mode upon SGMII interface selection.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
divamnt stores a start_time at module init and uses it to calculate
elapsed time. The elapsed time, stored in secs and usecs, is part of
the trace data the driver maintains for the DIVA Server ISDN cards.
No change to the format of that time data is required.
To avoid overflow on 32-bit systems use ktime_get_ts64() to return
the elapsed monotonic time since system boot.
This is a change from real to monotonic time. Since the driver only
stores elapsed time, monotonic time is sufficient and more robust
against real time clock changes. These new monotonic values can be
more useful for debugging because they can be easily compared to
other monotonic timestamps.
Note elaspsed time values will now start at system boot time rather
than module load time, so they will differ slightly from previously
reported values.
Remove declaration and init of previously unused time constants:
start_sec, start_usec.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-02-17
This series contains updates to i40e/i40evf once again.
Mitch updates the use of a define instead of a magic number. Adds support
for packet split receive on VFs, which is disabled by default. Expands on
a code comment which was not verbose or really helpful. Fixes an issue
where if a reset fails to complete and was not properly setting the
adapter state, which would cause a panic on rmmod, so set the adpater
state to DOWN to avoid a panic.
Jesse cleans up a "dump" in debugfs that never panned out to be useful.
Anjali adds a workaround for cases where we might have interrupts that get
lost but wright-back (WB) happened. Fixes an issue by falling back to
enabling unicast, multicast and broadcast promiscuous mode when the driver
must disable it's use of "default port" (defport mode) due to internal
incompatibility with Multiple Function per Port (MFP). Fixes an issue
where queues should never be enabled/disabled in the interrupt handler.
Kiran cleans up th code which used hard coded base VEB SEID since it was
removed from the specification.
Shannon adds a few bits for better debug messages. Fixes an obscure corner
case, where it was possible to clear the NVM update wait flag when no
update_done message was actually received.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ever since commit 04ed3e741d
("net: change netdev->features to u32") the format string
fmt_long_hex has not been used, so we may as well remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In MFP mode particularly when we were setting the PF VSI in limited
promiscuous, the HW switch was still mirroring the outgoing packets
from other VSIs (VF/VMdq) onto the PF VSI.
With this new bit set, the mirroring doesn't happen any more and so
we are in limited promiscuous on the PF VSI in MFP which is similar
to defport.
An API check is not required, since this bit is reserved for FW API
version < 1.5
Also update copyright year in file headers.
Change-ID: I9840cb95f11dde733d943cb03ce84f68b9611bc8
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In one obscure corner case, it was possible to clear the NVM update wait
flag when no update_done message was actually received. This patch
cleans the event descriptor before use, and moves the opcode check to
where it won't get done if there was no event to clean.
Also update copyright year in file headers.
Change-ID: I68bbc41965e93f4adf07cbe98b9dfd63d41509a4
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a reset fails to complete, the driver gets its affairs in order and
awaits the cold solace of rmmod. Unfortunately, it was not properly
setting the adapter state, which would cause a panic on rmmod, instead
of the desired surcease.
Set the adapter state to DOWN in this case, and avoid a panic.
Change-ID: I6fdd9906da52e023f8dc744f7da44b5d95278ca9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure we return EBUSY while finishing up a reset, and add a few bits
for better debug messages.
Change-ID: I23f6c28a8d96d7aa171abcc265737cec7826c292
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Explain why we cannot remove this code, even though it works differently
than any of our other interrupt cause handling code.
Change-ID: Ie66203bd037a466066036611c31d44f759ec5176
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The queues should never be enabled/disabled in the interrupt handler,
ICR0 interrupt enable should be the only thing that needs to be
dynamically changed in the handler.
This patch fixes that. Without this patch X722 platforms were
seeing weird ping timings when in Legacy mode since it takes
a whole lot of time for the HW/FW to re-enable queues.
Change-ID: If065afc45d81c5a19d4a94a00cd5b8f61cefc40c
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the case where we have a page fully used by receive data, we need to
release the page fully to the stack. Instead of calling get_page (which
increments the page count) followed by free_page (which decrements the
page count), just donate our reference to the stack. Although this
donation is not tax deductible, it does allow us to avoid two very
expensive atomic operations that reverse each other.
Change-ID: If70739792d5748995fc175ec92ac2171ed4ad8fc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixed mapping of SEID is removed from specification. Hence
this patch removes code which was using hard coded base VEB SEID.
Changed FCoE code to use "hw->pf_id" to obtain correct "idx"
and verified.
Removed defines for BASE VSI/VEB SEID and BASE_PF_SEID since it
is not used anymore.
Change-ID: Id507cf4b1fae1c0145e3f08ae9ea5846ea5840de
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch falls back to enabling unicast, multicast and
broadcast promiscuous mode when the driver must disable it's use
of "default port" aka defport mode (which is normally used to
provide a promiscuous mode), due to internal incompatibility
with Multiple Function per Port (aka MFP).
The situation that requires this patch is when Physical
Function 0 is the device being used, and it can support SR-IOV
when MFP is enabled, via the driver creating a VEB on an MFP
enabled adapter.
Change-ID: Ie90b00d0d58782a5dfcf2c3c9725a2eb90bd63d8
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a workaround for cases where we might have
interrupts that got lost but WB happened.
If that happens without this patch we will see a tx_timeout.
To work around it, this patch goes ahead and reschedules NAPI
in that situation, if NAPI is not already scheduled.
We also add a counter in ethtool to keep track of when
we detect a case of tx_lost_interrupt.
Note: napi_reschedule() can be safely called from process/service_task
context and is done in other drivers as well without an issue.
Change-ID: I00f98f1ce3774524d9421227652bef20fcbd0d20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes use of a pointer called hw consistent
in the i40e_remove function.
Change-ID: Idacc7ff0a09a68289c57457a78618bf5497de077
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Support packet split receive on VFs. This is off by default but can be
enabled using ethtool private flags. Because we need to trigger a reset
from outside of i40evf_main.c, create a new function to do so, and
export it.
Also update copyright year in file headers.
Change-ID: I721aa5d70113d3d6d94102e5f31526f6fc57cbbb
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There was a completely unused file "dump" in debugfs that
never panned out to be useful.
Change-ID: I12bb9e37b5a83299725dda815a8746157baf6562
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have a define for this, use it. No functional change.
Change-ID: Ic0e3ea4f562e46de63b2a8de07f291ccc10205fd
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jiri Benc says:
====================
vxlan: clean up rx path, consolidating extension handling
The rx path of VXLAN turned over time into kind of spaghetti code. The rx
processing is split between vxlan_udp_encap_recv and vxlan_rcv but in an
artificial way: vxlan_rcv is just called at the end of vxlan_udp_encap_recv,
continuing the rx processing where vxlan_udp_encap_recv left it. There's no
clear border between those two functions.
It makes sense to combine those functions into one; this will be actually
needed for VXLAN-GPE where we'll need to skip part of the processing which
is hard to do with the current code.
However, both functions are too long already. This patchset is shortening
them, consolidating extension handling that is spread all around together
and moving it to separate functions. (Later patchsets will do more
consolidation in other parts of the functions with the final goal of merging
vxlan_udp_encap_recv and vxlan_rcv.)
In process of consolidation of the extension handling, I needed to deal with
vni field in a generic way, as its lower 8 bits mean different things for
different extensions. While cleaning up the code to strictly distinguish
between "vni" and "vni field" (which contains vni plus an additional byte),
I also converted the code not to convert endianess back and forth.
The full picture can be seen at:
https://github.com/jbenc/linux-vxlan/commits/master
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For metadata based tunnels, VNI is ignored when doing vxlan device lookups
(because such tunnel receives all VNIs). However, this was not honored by
vxlan_xmit_one when doing encapsulation bypass. Move the check for metadata
based tunnel to the common place where it belongs.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there are unrecognized flags present in the vxlan header, it doesn't
make much sense to return the packet for further UDP processing, especially
considering that for other invalid flag combinations we drop the packet
because of previous checks.
This means we return positive value only at the beginning of the function
where tun_dst is not yet allocated. This allows us to get rid of the
bad_flags and error jump labels.
When we're dropping packet, we need to free tun_dst now.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring the extension handling to a single place and move the actual handling
logic out of vxlan_udp_encap_recv as much as possible.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make vxlan_udp_encap_recv shorter and more comprehensible.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part of the parameters is not needed. Simplify the caller of this function
in preparation of making vxlan rx more comprehensible.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent repeated conversions from and to network order in the fast path.
To achieve this, define all flag constants in big endian order and store VNI
as __be32. To prevent confusion between the actual VNI value and the VNI
field from the header (which contains additional reserved byte), strictly
distinguish between "vni" and "vni_field".
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, pointer to the vxlan header is kept in a local variable. It has
to be reloaded whenever the pskb pull operations are performed which usually
happens somewhere deep in called functions.
Create a vxlan_hdr function and use it to reference the vxlan header
instead.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-02-17
This series contains updates to i40e/i40evf only (again).
Jesse moves sync_vsi_filters() up in the service_task because it may need
to request a reset, and we do not want to wait another round of service
task time. Refactored the enable_icr0() in order to allow it to be
decided by the caller whether the CLEARPBA (clear pending events) bit will
be set while re-enabling the interrupt. Also provides the "Don't Give Up"
patch, where the driver will keep polling trying to allocate receive buffers
until it succeeds. This should keep all receive queues running even in
the face of memory pressure. Cleans up the debugging helpers by putting
everything in hex to be consistent.
Neerav updates the DCB firmware version related checkes specific to X710
and XL710 only since the checks are not required for X722 devices.
Shannon adds the use of the new shared MAC filter bit for multicast and
broadcast filters in order to make better use of the filters available
from the device. Added a parameter to allow the driver to set the
enable/disable of statistics gathering in the hardware switch. Also the
L2 cloud filtering parameter is removed since it was never used.
Anjali refactors the force_wb and WB_ON_ITR functionality since
Force-WriteBack functionality in X710/XL710 devices has been moved out of
the clean routine and into the service task, so we need to make sure
WriteBack-On-ITR is separated out since it is still called from clean.
Catherine changes the VF driver string to reflect all the products that
are supported.
Mitch refactors the packet split receive code to properly use half-pages
for receives. Also changes the use of bitwise operators to logical
operators on clean_complete variable, while making a witty reference to
Mr. Spock. Cleans up (i.e. removes) the hsplit field in the ring
structure and use the existing macro to detect packet split enablement,
which allows debugfs dumps of the VSI to properly show which recevie
routine is in use.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
rocker: do world split
This patchset allows new rocker worlds to be easily added in future.
Two new worlds are now under development: P4 and eBPF.
The main part of the patchset is the OF-DPA carve-out. It resuts in OF-DPA
specific file. Clean cut.
Note this patchset is based on my original attempt in October 2015.
I had to rebase, included all suggestions and did lot of small changes.
Main change to go with all-port-one-world approach. Port world is set according
to what is setup in HW. Not possible to change worlds from driver.
v1->v2:
patch 12/13:
- split port_init into pre-init and init
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Carve out OF-DPA would specific code from the common file to the world
file. This change required struct rocker and struct rocker_port split
into world specific struct ofdpa and struct ofdpa_port. Along with this
the world specific functions and defines were renamed from prefix
"rocker_" to "ofdpa_".
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to push down rocker flags just to check if this is nowait or
not. Let the caller handle that.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only purpose of passing this parameter is to check for
prepare phase. The only reason for a failure in that state is if
TLVs don't fit into descriptor. That is highly unlikely and if that
happens, it is a driver bug. So remove this parameter from
rocker_cmd_exec, and check for prepare phase in caller.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids need to alloc/free wait structure for every command call.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be consistent with the rest of the setting functions, and pass
"learning" as a bool function parameter.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is another step on the way to per-world clean cut. Introduce world
ops hooks which each world can implement in world-specific way.
Also introduce world infrastructure along with OF-DPA world stub.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And take some other related thing along. They are going to be pushed
into of-dpa part anyway.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a helper to ask HW for the port mode (world).
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Carve out TLV processing helpers into separate files.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since "rocker.c" is going to be split into multiple files, start with
renaming original "rocker.c" file to "rocker_main.c". Multiple code
parts are going to be cut from "rocker_main.c" later on.
Fix couple of checkpatch issues on the way.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck