This patch adds a feature to dynamically replace the ftrace code
with the jmps to allow a kernel with ftrace configured to run
as fast as it can without it configured.
The way this works, is on bootup (if ftrace is enabled), a ftrace
function is registered to record the instruction pointer of all
places that call the function.
Later, if there's still any code to patch, a kthread is awoken
(rate limited to at most once a second) that performs a stop_machine,
and replaces all the code that was called with a jmp over the call
to ftrace. It only replaces what was found the previous time. Typically
the system reaches equilibrium quickly after bootup and there's no code
patching needed at all.
e.g.
call ftrace /* 5 bytes */
is replaced with
jmp 3f /* jmp is 2 bytes and we jump 3 forward */
3:
When we want to enable ftrace for function tracing, the IP recording
is removed, and stop_machine is called again to replace all the locations
of that were recorded back to the call of ftrace. When it is disabled,
we replace the code back to the jmp.
Allocation is done by the kthread. If the ftrace recording function is
called, and we don't have any record slots available, then we simply
skip that call. Once a second a new page (if needed) is allocated for
recording new ftrace function calls. A large batch is allocated at
boot up to get most of the calls there.
Because we do this via stop_machine, we don't have to worry about another
CPU executing a ftrace call as we modify it. But we do need to worry
about NMI's so all functions that might be called via nmi must be
annotated with notrace_nmi. When this code is configured in, the NMI code
will not call notrace.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add preempt off timings. A lot of kernel core code is taken from the RT patch
latency trace that was written by Ingo Molnar.
This adds "preemptoff" and "preemptirqsoff" to /debugfs/tracing/available_tracers
Now instead of just tracing irqs off, preemption off can be selected
to be recorded.
When this is selected, it shares the same files as irqs off timings.
One can either trace preemption off, irqs off, or one or the other off.
By echoing "preemptoff" into /debugfs/tracing/current_tracer, recording
of preempt off only is performed. "irqsoff" will only record the time
irqs are disabled, but "preemptirqsoff" will take the total time irqs
or preemption are disabled. Runtime switching of these options is now
supported by simpling echoing in the appropriate trace name into
/debugfs/tracing/current_tracer.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds the latency tracer infrastructure. This patch
does not add anything that will select and turn it on, but will
be used by later patches.
If it were to be compiled, it would add the following files
to the debugfs:
The root tracing directory:
/debugfs/tracing/
This patch also adds the following files:
available_tracers
list of available tracers. Currently no tracers are
available. Looking into this file only shows
"none" which is used to unregister all tracers.
current_tracer
The trace that is currently active. Empty on start up.
To switch to a tracer simply echo one of the tracers that
are listed in available_tracers:
example: (used with later patches)
echo function > /debugfs/tracing/current_tracer
To disable the tracer:
echo disable > /debugfs/tracing/current_tracer
tracing_enabled
echoing "1" into this file starts the ftrace function tracing
(if sysctl kernel.ftrace_enabled=1)
echoing "0" turns it off.
latency_trace
This file is readonly and holds the result of the trace.
trace
This file outputs a easier to read version of the trace.
iter_ctrl
Controls the way the output of traces look.
So far there's two controls:
echoing in "symonly" will only show the kallsyms variables
without the addresses (if kallsyms was configured)
echoing in "verbose" will change the output to show
a lot more data, but not very easy to understand by
humans.
echoing in "nosymonly" turns off symonly.
echoing in "noverbose" turns off verbose.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If CONFIG_FTRACE is selected and /proc/sys/kernel/ftrace_enabled is
set to a non-zero value the ftrace routine will be called everytime
we enter a kernel function that is not marked with the "notrace"
attribute.
The ftrace routine will then call a registered function if a function
happens to be registered.
[ This code has been highly hacked by Steven Rostedt and Ingo Molnar,
so don't blame Arnaldo for all of this ;-) ]
Update:
It is now possible to register more than one ftrace function.
If only one ftrace function is registered, that will be the
function that ftrace calls directly. If more than one function
is registered, then ftrace will call a function that will loop
through the functions to call.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Steven Rostedt