Previously, mlx5_ib_cq_comp was executed from interrupt context.
Under heavy load, this could cause the CPU core to be in an interrupt
context too long.
Instead of executing the handler from the interrupt context we
execute it from a much friendly tasklet context.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In the Ethernet/TCP world, CAP_NET_RAW is sufficient to allow a program
to listen to all incoming packets on a specific interface, and the
higher CAP_NET_ADMIN is required to set the interface into promiscuous
mode. We want to emulate that same basic division of privilege in the
RDMA stack, so when dealing with Raw Ethernet QPs, allow apps with
CAP_NET_RAW to listen to all incoming flows (and direct them as they see
fit in their own listen stream). Do not require CAP_NET_ADMIN just to
listen to traffic already incoming. Reserve CAP_NET_ADMIN if we attempt
to set promiscuous mode.
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The problem is that the function 'send_reply_to_slave' gets the
'req_sa_mad' as a pointer whose address is only aliged to 4 bytes
but is 8 bytes in size. This can result in unaligned access faults
on certain architectures.
Sowmini Varadhan pointed to this reply from Dave Miller that say
that memcpy should not be used to solve alignment issues:
https://lkml.org/lkml/2015/10/21/352
Optimization of memcpy to 'ldx' instruction can only happen if the
compiler knows that the size of the data we are copying is 8 bytes
and it assumes it is aligned to 8 bytes. If the compiler know the
type is not aligned to 8 it must not optimize the 8 byte copy.
Defining the data type as aligned to 4 forces the compiler to treat
all accesses as though they aren't aligned and avoids the 'ldx'
optimization.
Full credit for the idea goes to Jason Gunthorpe
<jgunthorpe@obsidianresearch.com>.
Signed-off-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Instead of special casing the handful of callers that check for
iser-target rdma verbs specific shutdown, use a simple flag at
iscsit_transport->rdma_shutdown so each driver can signal this.
Also, update iscsi-target/tcp + cxgbit to rdma_shutdown = false.
Cc: Varun Prakash <varun@chelsio.com>
Cc: Hariprasad Shenai <hariprasad@chelsio.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Report Scatter FCS support when the Firmware supports as well.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Enable Scatter FCS in the RQ context when the user passes
Scatter FCS create flag.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Raw Packet QPs that were created with Scatter FCS flag, will scatter
the FCS into the receive buffers.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Since all the uverbs device_cap_flags are occupied, we need a place to
expose more device capabilities.
This patch adds a new 64 bit device_cap_flags_ex to expose new
device capabilities.
The lower 32 bits will be identical to the original device_cap_flags,
The upper 32 bits will be new capabilities.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
passing hw_stats by value requires a 280 byte copy so instead
pass it by reference is much more efficient.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Chien Tin Tung <chien.tin.tung@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
free_irq(irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Faisal Latif <faisal.latif#intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The i40iw_vf_cqp_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
By this patch, the user space library will be able to improve
performance using appropriate ringing DoorBell method according to the
memory type it asked for.
Currently only one mapping command is allowed for UARs:
MLX5_IB_MMAP_REGULAR_PAGE. Using this mapping, the kernel maps the
UARs to write-combining (WC) if the system supports it.
If the system is not supporting WC the UARs are mapped to
non-cached(NC). In this case the user space library can't tell which
mapping is applied.
This patch adds 2 new mapping commands: MLX5_IB_MMAP_WC_PAGE and
MLX5_IB_MMAP_NC_PAGE. For these commands the kernel maps exactly as
requested and fails if it can't.
Since there is no generic way to check if the requested memory region
can be mapped as WC, driver enables conclusive WC mapping only for
x86, PowerPC and ARM which support WC for the device's memory region.
Signed-off-by: Guy Levy <guyle@mellanox.com>
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The current mlx5 code disallows mapping the free running counter of
mlx5 based hardwares when PROT_EXEC is set.
Although this behaviour is correct, Linux does add an implicit VM_EXEC
to the vm_flags if the READ_IMPLIES_EXEC bit is set in the process
personality. This happens for example if the process stack is
executable.
This causes libmlx5 to output a warning and prevents the user from
reading the free running clock.
Executing the init segment of the hardware isn't a security risk
(at least no more than executing a process own stack), so we just
prevent writes to there.
Fixes: d69e3bcf79 ('IB/mlx5: Mmap the HCA's core clock register to
user-space')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Simplify the code in search_relocate_mgid0_group with by using
list_for_each_entry_safe().
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fixes a direct call to kfree_skb when nlmsg_free should be used.
Fixes: 2ca546b92a ('IB/sa: Route SA pathrecord query through netlink')
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix array overrun when going over callback table.
In declaration of callback table, the max size isn't provided and
in registration phase, it is provided.
There is potential scenario where a new operation is added
and it is not supported by current client. The acceptance of
such operation by ib_netlink will cause to array overrun.
Fixes: 809d5fc9bf ("infiniband: pass rdma_cm module to netlink_dump_start")
Fixes: b493d91d33 ("iwcm: common code for port mapper")
Fixes: 2ca546b92a ("IB/sa: Route SA pathrecord query through netlink")
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
RDMA_NL_GET_OP is defined like this: (type & ((1 << 10) - 1))
which means op (defined as an int) can never be a negative number.
Fixes: b2cbae2c24 ('RDMA: Add netlink infrastructure')
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In case ibnl_put_msg fails in send_nlmsg_done,
the function returns with -ENOMEM without freeing.
This patch fixes this behavior.
Fixes: 30dc5e63d6 ("RDMA/core: Add support for iWARP Port Mapper user space service")
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is no need to duplicate a lot of code that is in the kernel library for ages.
Replace duplicating code by calling to print_hex_dump() directly.
Note that output is slightly changed:
- hex and ascii parts have just two spaces delimeter
- there is no delimeter for ascii portions
- file and line removed from prefix (they were redundant anyway since previous
output shows same closer enough)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
fix spelling mistake, argumant -> argument
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This function compiles to 550 bytes of machine code.
Three callsites, all in nes_create_qp.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Faisal Latif <faisal.latif@intel.com>
CC: Doug Ledford <dledford@redhat.com>
CC: linux-rdma@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Reviewed-By: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Adding sq and rq drain functions, which block until all
previously posted wr-s in the specified queue have completed.
A completion object is signaled to unblock the thread,
when the last cqe for the corresponding queue is processed.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that sparse complains about the comparison of s_addr
with INADDR_ANY.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Steve Wise <swise@opengridcomputing.com>
Cc: Faisal Latif <faisal.latif@intel.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
IPoIB collects statistics of traffic including number of packets
sent/received, number of bytes transferred, and certain errors. This
patch makes these statistics available to be queried by ethtool.
Signed-off-by: Hans Westgaard Ry <hans.westgaard.ry@oracle.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Tested-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The last user of pkey_mutex was removed in db84f88037 ("IB/ipoib: Use
P_Key change event instead of P_Key polling mechanism") but the lock
remained.
This patch removes it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
passing hw_stats by value requires a 280 byte copy so instead
pass it by reference is much more efficient.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Chien Tin Tung <chien.tin.tung@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
free_irq(irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Faisal Latif <faisal.latif#intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The i40iw_vf_cqp_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The priority of the send engines is higher than the CQ completion
thread potentially causing completions to be starved for very
fast interfaces.
Change the CQ kthread to match the send engine threads to minimize
this delay for ULP completion processing.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
__force casts should be avoided if there is a better alternative.
Hence modify the comparison of s_addr with INADDR_ANY such that the
__force cast is no longer necessary.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Steve Wise <swise@opengridcomputing.com>
Cc: Vipul Pandya <vipul@chelsio.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
These handlers when called print error message to the kernel log,
but the actual handling is done by _c4iw_free_ep() and process_timeout().
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently c4iw_peer_abort_intr() does not wake up the waiter if the
endpoint state indicates we're using MPAv2 and we're currently trying to
connect. This was introduced with commit 7c0a33d611 ("RDMA/cxgb4:
Don't wakeup threads for MPAv2")
However, this original fix is flawed because it introduces a race that
can cause a deadlock of the iwarp stack. Here is the race:
->local side sets up an active offload connection.
->local side sends MPA_START request.
->peer sends MPA_START response.
->local side ingress cpl thread begins processing the MPA_START response,
but before it changes the state from MPA_REQ_SENT to FPDU_MODE:
->peer sends a RST which results in a ABORT_REQ_RSS. This triggers
peer_abort_intr() which sees the state in MPA_REQ_SENT and since mpa_rev
is 2, it will avoid waking up the endpoint with -ECONNRESET, assuming the
stack will re-attempt the connection using MPAv1.
->Meanwhile, the cpl thread moves the state to FPDU_MODE and calls
c4iw_modify_rc_qp() which calls rdma_init() which sends a RI_WR/INIT WR
to firmware. But since HW sent an abort, FW correctly drops the RI_WR/INIT
WR.
->So the cpl thread is stuck waiting for a reply and cannot process the
ABORT_REQ_RSS cpl sitting in its input queue. Thus everything comes to a
halt because no more ingress cpls are processed by the stack...
The correct fix for the issue is to always do the wake up in
c4iw_abort_intr() but reinitialize the wait object in c4iw_reconnect().
Fixes: 7c0a33d611 ("RDMA/cxgb4: Don't wakeup threads for MPAv2")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add get_ep_from_stid() which will atomically find and reference the
endpoint struct if found. This avoids touch-after-free races between
threads destroying listening endpoints and the CPL processing thread
processing an incoming PASS_ACCEPT_REQ CPL.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
c4iw_reject() and c4iw_accept() need to handle the case where the
endpoint has timed out and is in the middle of ABORTING the connection.
Here is the flow that causes the BUG_ON() to fire on the server side:
1) offload connection setup and endpoint timer started
2) MPA_START request received from peer, CONNECT_REQUEST passed to ULP
3) endpoint timer fires, and process_timeout() aborts the connection,
this moves the endpoint state to ABORTING until HW sends up the
ABORT_RPL_RSS.
4) application exits closing the CONNECT_REQUEST cm_id. The IWCM calls
c4iw_reject_cr() to destroy this connection request.
5) WHAMO: BUG_ON() because the state is ABORTING.
The fix is to change c4iw_reject_cr() and c4iw_accept_cr() to fail the
operation if the state is not in MPA_REQ_RCVD vs in DEAD.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
ARP failure may also happen when ep in FPDU_MODE and these failures need
to be handled by process_timeout(). process_timeout() also has to handle
case MPA_REQ_RCVD, setting abort to 1, leading to ep resource release.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Arp failure for send_mpa_reply/reject() is handled by freeing the
mpa_skb in c4iw_free_ep() before releasing ep.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is a race between ULP threads calling c4iw_ep_disconnect() via
c4iw_modify_rc_qp() and the ingress CPL thread where the ULP thread
can free the endpoint just after the ingress CPL thread finds the ep
pointer in the tid table. To avoid this, we now use the hwtid_idr table
for lookups instead of the LLD tid table so we can lock around insert,
remove, and lookup+get_ep to avoid the race. The CPL handlers now will
either find the ep ptr and have a ref on it, or not find it and they
can discard the CPL. Callers of get_ep_from_tid() will have a ref
on the ep if found, and thus must deref when they are done.
Negative advice in peer_abort_intr() need to dereference the ep.
therefore peer_abort() is scheduled to dereference the ep later.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In abort_arp_failure(), the return value from c4iw_ofld_send() is
ignored and thus if the CPL isn't sent, the endpoint is stuck and never
gets aborted. Failure of c4iw_ofld_send() is treated as fatal error, and
the ep resources are released in a safer context through process_work().
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Moving the state to ABORTING causes the ep to get stuck because
c4iw_ep_timeout() thinks the ABORT has already been done. So leave the
state alone and let c4iw_ep_disconnect() do the right thing given the
ep state.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
->In act_open_rpl(), CPL_ERR_TCAM_FULL error handling branch, there is
no handling of the return value of send_fw_act_open_req().
->In send_fw_act_open_req(), there is no handling of return value of
c4iw_l2t_send(), which may cause a ep leak and won't notify upper layers
on connection establish failure.
->send_mpa_req() should act on the return from c4iw_l2t_send() and
return the error to the caller.
->In case of c4iw_l2t_send() failure in send_mpa_req(), returns without
starting the timer and not changing the ep state, which is further
handled by act_establish()
-> In act_establish()?if send_mpa_request's get_skb returns an error,
may cause an ep leak. So handle return value of send_mpa_req()
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
->Stop the ep timer after MPA negotiation so that the arp failures
during send_mpa_reply/reject will be handled by process_timeout() after
the ep timer expires.
->Added case MPA_REP_SENT in process_timeout().
->For MPA reject, c4iw_ep_disconnect tries to start an already started
timer, which leads to warning message "timer already started".
-> In case of mpa reject stop the timer and call send_mpa_reject().
-> Added new ep flag STOP_MPA_TIMER to tell fw4_ack() to stop the timer
only for send_mpa_reply(), which is set in c4iw_accept_cr().
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In case of incomplete mpa messages we should not stop timer as it
results in return with timeout for the next mpa message
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
-> On passive side of connection parent_ep referenced during connection
request has to be dereferenced during the passive accept failure.
-> As passive accept failure error handlinglogic runs in atomic context,
the parent ep is dereferenced by scheduling work request.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The FID value in a ULP_MEMIO command needs to be set to an IQ ID of
a queue configured for our PF. The FID/IQ id is used to index into the
PCIE FID table, to find out on which function the DMA needs to be
issued. Essentially, every DMA needs to have the ingress queue. The exact
ingress queue doesn't matter, but it needs to be an ingress queue
associated with the function you want to see the DMA on.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
- add EP_DISC_FAIL history bit
- add QP_REFED/DEREFED history bits
- Add functions to ref/deref the cm_id and add history bit for the same
- add CLOSE_CON_RPL history
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
passing hw_stats by value requires a 280 byte copy so instead
pass it by reference is much more efficient.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Chien Tin Tung <chien.tin.tung@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
free_irq(irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Faisal Latif <faisal.latif#intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The i40iw_vf_cqp_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The i40e_client_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This makes it easier to test the code path that does not use
memory registration (srp_map_sg_dma()).
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If both max_sectors and the queue_depth are high enough it can
happen that the MR pool is depleted temporarily. This causes
the SRP initiator to report mapping failures. Although the SRP
initiator recovers from such mapping failures, prevent that
this can happen by allocating more memory regions.
Additionally, only enable memory registration if at least two
pages can be registered per memory region.
Reported-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch does not change any functionality but makes the next
patch in this series easier to read.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The SRP initiator allows to set max_sectors to a value that exceeds
the largest amount of data that can be mapped at once with an mlx4
HCA using fast registration and a page size of 4 KB. Hence modify
ib_map_mr_sg() such that it can map partial sg-elements. If an
sg-element has been mapped partially, let the caller know
which fraction has been mapped by adjusting *sg_offset.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If an error occurs after srp_fr_pool_get() succeeded and before the
descriptor is stored in srp_map_state (*state->fr.next++ = desc)
then srp_unmap_data() won't free the newly allocated memory
descriptor. Hence free the descriptor explicitly.
Fixes: f7f7aab1a5 ("IB/srp: Convert to new registration API")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Cc: Sagi Grimberg <sai@grimberg.me>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Doug Ledford <dledford@redhat.com>
pr_debug() already prints prefix PFX. Avoid that PFX is printed
twice if the debug statement in srp_add_target() is enabled.
Fixes: 34aa654ecb ("IB/srp: Avoid that I/O hangs due to a cable pull during LUN scanning")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Replace the homegrown RDMA READ/WRITE code in isert with the generic API,
which also adds iWarp support to the I/O path as a side effect. Note
that full iWarp operation will need a few additional patches from Steve.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Replace the homegrown RDMA READ/WRITE code in srpt with the generic API.
The only real twist here is that we need to allocate one Linux scatterlist
per direct buffer in the SRP command, and chain them before handing them
off to the target core.
As a side-effect of the conversion the driver will also chain the SEND
of the SRP response to the RDMA WRITE WRs for a DATA OUT command, and
properly account for RDMA WRITE WRs instead of just for RDMA READ WRs
like the driver previously did.
We now allocate half of the SQ size to RDMA READ/WRITE contexts, assuming
by default one RDMA READ or WRITE operation per command. If a command
has multiple operations it will eat into the budget but will still succeed,
possible after waiting for WQEs to be available.
Also ensure the QPs request the maximum allowed SGEs so that RDMA R/W API
works correctly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This supports both manual mapping of lots of SGEs, as well as using MRs
from the QP's MR pool, for iWarp or other cases where it's more optimal.
For now, MRs are only used for iWARP transports. The user of the RDMA-RW
API must allocate the QP MR pool as well as size the SQ accordingly.
Thanks to Steve Wise for testing, fixing and rewriting the iWarp support,
and to Sagi Grimberg for ideas, reviews and fixes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This is the first step toward moving MR invalidation decisions
to the core. It will be needed by the upcoming RW API.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Split the XRC magic into a separate function, and return early on failure
to make the initialization code readable.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The new RW API will need this.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Since all srp_map_finish_fr() callers pass a non-zero value as
the fourth argument (sg_nents), the sg_nents == 0 check in that
function can be removed. Add a count == 0 check in the caller
of that function.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The srp_queuecommand() function translates ENOMEM into QUEUE_FULL
which causes the SCSI mid-layer to retry the command. All other
error codes are translated into DID_ERROR which causes the SCSI
command to fail. Return E2BIG if mapping will always fail to
prevent that the SCSI mid-layer keeps resubmitting a command
forever.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Ensure that req->nmdesc is set correctly in srp_map_sg() if mapping
fails. Avoid that mapping failure causes a memory descriptor leak.
Report srp_map_sg() failure to the caller.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The free request list was removed through patch "IB/srp: Use block layer tags".
Hence update a comment that refers to that free request list.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Turns out the template and thus many drivers got the return value wrong:
0 means the fabrics driver needs to put a session reference, which no
driver except for the iSCSI target drivers did. Fortunately none of these
drivers supports explicit Node ACLs, so the bug was harmless.
Even without that only qla2xxx and iscsi every did real work in
shutdown_session, so get rid of the boilerplate code in all other
drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add void (*iscsit_get_rx_pdu)() to
struct iscsit_transport, iscsi-target
uses this callback to receive and
process Rx iSCSI PDUs.
cxgbit.ko needs this callback to
reuse iscsi-target Rx thread.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-05-05
This series contains updates to i40e and i40evf.
The theme behind this series is code reduction, yeah! Jesse provides
most of the changes starting with a refactor of the interpretation of
a tunnel which lets us start using the hardware's parsing. Removed
the packet split receive routine and ancillary code in preparation
for the Rx-refactor. The refactor of the receive routine,
aligns the receive routine with the one in ixgbe which was highly
optimized. The hardware supports a 16 byte descriptor for receive,
but the driver was never using it in production. There was no performance
benefit to the real driver of 16 byte descriptors, so drop a whole lot
of complexity while getting rid of the code. Fixed a bug where while
changing the number of descriptors using ethtool, the driver did not
test the limits of the system memory before permanently assuming it
would be able to get receive buffer memory.
Mitch fixes a memory leak of one page each time the driver is opened by
allocating the correct number of receive buffers and do not fiddle with
next_to_use in the VF driver.
Arnd Bergmann fixed a indentation issue by adding the appropriate
curly braces in i40e_vc_config_promiscuous_mode_msg().
Julia Lawall fixed an issue found by Coccinelle, where i40e_client_ops
structure can be const since it is never modified.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The i40e_client_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The dma_alloc_coherent() function returns a virtual address which can
be used for coherent access to the underlying memory. On some
architectures, like arm64, undefined behavior results if this memory is
also accessed via virtual mappings that are not coherent. Because of
their undefined nature, operations like virt_to_page() return garbage
when passed virtual addresses obtained from dma_alloc_coherent(). Any
subsequent mappings via vmap() of the garbage page values are unusable
and result in bad things like bus errors (synchronous aborts in ARM64
speak).
The mlx4 driver contains code that does the equivalent of:
vmap(virt_to_page(dma_alloc_coherent)), this results in an OOPs when the
device is opened.
Prevent Ethernet driver to run this problematic code by forcing it to
allocate contiguous memory. As for the Infiniband driver, at first we
are trying to allocate contiguous memory, but in case of failure roll
back to work with fragmented memory.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reported-by: David Daney <david.daney@cavium.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use c4iw_ep_disconnect() instead. This is part of getting rid of
abort_connection() altogether so we properly clean up on send_abort()
failures.
This is the last user of abort_connection(), so remove it too.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In c4iw_ep_disconnect(), if we fail to initiate a close operation, then
move the qp to ERROR to disassociate the ep from the qp. Failure to do
this will leak the ep resources.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Instead return whether the caller needs to disconnect. This is part of
getting rid of abort_connection() altogether so we properly clean up on
send_abort() failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use c4iw_ep_disconnect() instead. This is part of getting rid of
abort_connection() altogether so we properly clean up on send_abort()
failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Instead, have the caller, rx_data() handle the close/abort like
it does for process_mpa_request(). This is part of getting rid of
abort_connection() altogether so we properly clean up on send_abort()
failures.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In rx_data(), with the ep in FPDU_MODE, refcnt=2, if we get unexpected
streaming data, we call c4iw_modify_rc_qp() and move the qp from
RTS -> TERMINATE. In c4iw_modify_rc_qp(), if rdma_fini() returns
an error, the ep will be dereferenced (refcnt=1). Then rx_data()
calls c4iw_ep_disconnect() which starts the close operation.
But if send_halfclose() fails in c4iw_ep_disconnect(), we will call
release_ep_resources() derefing the ep which reduces the refcnt to 0 and
and frees the ep. However we still has the ep mutex at that point, so we
have a touch-after-free bug. There is a similar issue where
peer_close() calls c4iw_ep_disconnect().
The solution is to add a reference to the ep in c4iw_ep_disconnect()
after acquiring the mutex, and release it after releasing the mutex.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In c4iw_ep_disconnect(), if we start the ep timer to begin a close,
but send_halfclose() fails, we need to stop the timer and send a CLOSE
event up to the IWCM before releasing the resources. Otherwise, we can
crash when the ep timer fires if the ep is referencing a previous instance
of the device. This can happen as part of adapter reset/recovery, for
instance.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If ARP fails before the CPL_PASS_ACCEPT_RPL is seen by hardware, the tid
will be stuck in SYN_PEND and never released. So create an arp failure
handler specifically for this message to release the endpoint resources.
In pass_accept_rpl_arp_failure(), put the parent endpoint so it will
be freed when destroyed. Also we don't need to call release_tid() here
because _c4iw_free_ep() calls cxgb4_remove_tid() which releases the
hwtid.
If we get an ABORT_REQ_RSS instead of a PASS_ESTABLISH (because the
peer's ACK to our SYN is never received), then put the parent as well
in peer_abort().
Treat accept_cr() failures just like arp failures: put the parent ep
and release the ep resources destroying the tid
The ARP failure handlers are called in an atomic context, so we need to
schedule some of the processing which might block. Namely _c4iw_free_ep()
which needs a mutex. So create a "special" CPL opcode and handler and
schedule it via sched() to be run by process_work() in a blockable context.
Also rework the active open arp failure handler to make use of
release_ep_resources(). This allows both the active and passive arp
failure handlers to use the same deferred cleanup function.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
iSER currently has a couple places that set max_sectors in either the host
template or SCSI host, and all of them get it wrong.
This patch instead uses a single assignment that (hopefully) gets it right:
the max_sectors value must be derived from the number of segments in the
FR or FMR structure, but actually be one lower than the page size multiplied
by the number of sectors, as it has to handle the case of non-aligned I/O.
Without this I get trivial to reproduce hangs when running xfstests
(on XFS) over iSER to Linux targets.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
a trans_start struct member exists twice:
- in struct net_device (legacy)
- in struct netdev_queue
Instead of open-coding dev->trans_start usage to obtain the current
trans_start value, use dev_trans_start() instead.
This is not exactly the same, as dev_trans_start also considers
the trans_start values of the netdev queues owned by the device
and provides the most recent one.
For legacy devices this doesn't matter as dev_trans_start can cope
with netdev trans_start values of 0 (they are ignored).
This is a prerequisite to eventual removal of dev->trans_start.
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was requesting for a writethrough mapping. But with those
flags we will end up with an SAO mapping because we now have memory
conherence always enabled. ie, the existing mapping will end up with a
WIMG value 0b1110 which is Strong Access Order.
Update this to use cache inhibitted guarded mapping.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- A number of collected fixes for oopses, memory corruptions, deadlocks,
etc. All of these fixes are small (many only 5-10 lines), obvious,
and tested.
- Fix for the security issue related to the use of write for
bi-directional communications.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MFdC
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Final set of -rc fixes for 4.6.
I've collected up a number of patches that are all pretty small with
the exception of only a couple. The hfi1 driver has a number of
important patches, and it is what really drives the line count of this
pull request up. These are all small and I've got this kernel built
and running in the test lab (I have most of the hardware, I think nes
is the only thing in this patch set that I can't say I've personally
tested and have up and running).
Summary:
- A number of collected fixes for oopses, memory corruptions,
deadlocks, etc. All of these fixes are small (many only 5-10
lines), obvious, and tested.
- Fix for the security issue related to the use of write for
bi-directional communications"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
RDMA/nes: don't leak skb if carrier down
IB/security: Restrict use of the write() interface
IB/hfi1: Use kernel default llseek for ui device
IB/hfi1: Don't attempt to free resources if initialization failed
IB/hfi1: Fix missing lock/unlock in verbs drain callback
IB/rdmavt: Fix send scheduling
IB/hfi1: Prevent unpinning of wrong pages
IB/hfi1: Fix deadlock caused by locking with wrong scope
IB/hfi1: Prevent NULL pointer deferences in caching code
MAINTAINERS: Update iser/isert maintainer contact info
IB/mlx5: Expose correct max_sge_rd limit
RDMA/iw_cxgb4: Fix bar2 virt addr calculation for T4 chips
iw_cxgb4: handle draining an idle qp
iw_cxgb3: initialize ibdev.iwcm->ifname for port mapping
iw_cxgb4: initialize ibdev.iwcm->ifname for port mapping
IB/core: Don't drain non-existent rq queue-pair
IB/core: Fix oops in ib_cache_gid_set_default_gid
Currently, consumers of the flow steering infrastructure can't
choose their own flow table levels and are limited to one
flow table per level. This just waste levels.
Instead, we introduce here the possibility to use multiple
flow tables in a level. The user is free to connect these
flow tables, while following the rule (FTEs in FT of level x
could only point to FTs of level y where y > x).
In addition this patch switch the order of the create/destroy
flow tables of the NIC(vlan and main).
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alternatively one could free the skb, OTOH I don't think this test is
useful so just remove it.
Cc: <linux-rdma@vger.kernel.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix for removing a quad hash entry when the
corresponding quad hash entry hasn't been added,
which is the case in loopback connections
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix for checking if the QP associated with a completion
has been destroyed while processing CQ elements.
If that is the case, move the CQ head to the next element
and continue completion processing.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
A check is added to validate the requested sge number.
iWARP doesn't support multiple sg elements for
RDMA READ work requests.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix to calculate the SQ size based on the max
frag_count, requested by the application instead
of overwriting it with the max supported frag_count
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
STag index mask is calculated incorrectly, missing
the 14 bits minimum requirement. Add max macro to use
either # of MRs or 14 bits in the mask size calculation.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Invalidation after every WQE write is changed to invalidate
only if required. NOPs are padded so that WQE writes are
aligned to 64B boundary.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Adding sq and rq drain functions, which block until all
previously posted wr-s in the specified queue have completed.
A completion object is signaled to unblock the thread,
when the last cqe for the corresponding queue is processed.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Correct SD calculation by using base address returned from commit FPM.
This alleviates any assumptions on resource ordering and alignment
requirement. Also consolidate SD estimation code into i40iw_est_sd().
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix endian warnings and errors due to u32 stored to u16.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Implement fast register mr, Local invalidate, send with
invalidate and RDMA read with invalidate.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Initialize max enabled vfs to max rdma vfs instead of 0.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Move return code check to immediately after i40iw_hmc_sd_one call
where it is set instead of outside the then statement.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Queue users of virtual channel on a waitqueue until the channel is
clear instead of failing the call when the channel is occupied.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add a check for cq_poll_info.error before setting vendor_err
instead of always setting it.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
QP may be freed during Async Event processing.
Add a lock around QP table to prevent it.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
iwqp->allocated_buffer is a self-referencing pointer to iwqp.
Do not set iwqp->allocated_buffer to NULL after freeing it.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Make sure cm_node is setup before sending SYN packet and
ORD/IRD negotiation.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Include inline data size as part of SQ size calculation.
RQ size calculation uses only number of SGEs and does not
support 96 byte WQE size.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Change region_length to u64 as a region can be > 4GB.
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The awkward coding for setting the allowed_ops field
was tripping an smatch warning.
This patch uses the more appropriate defines from include/rdma
to avoid the issue.
As part of the patch remove a mask that was duplicated
in rdmavt include files and use that mask as appropriate.
Fixes: 8bea6b1cfe6f ("IB/rdmavt: Add create queue pair functionality")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
rdi->ports has memory allocated in rvt_alloc_device(), but does not get
freed because the hfi1 and qib drivers drivers call ib_dealloc_device()
directly instead of going through rdmavt. Add a rvt_dealloc_device()
that frees rdi->ports and then calls ib_dealloc_device(). Switch hfi1
and qib drivers to calling rvt_dealloc_device() instead of
ib_dealloc_device() directly.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Brian Welty <brian.welty@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The dual lock patch moved locking around and missed an issue
with handling irq flags when processing UD loopback
packets. This issue was revealed by smatch.
Fix for both qib and hfi1 to pass the saved flags to the UD request
builder and handle the changes correctly.
Fixes: 46a80d62e6 ("IB/qib, staging/rdma/hfi1: add s_hlock for use in post send")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The drivers/infiniband stack uses write() as a replacement for
bi-directional ioctl(). This is not safe. There are ways to
trigger write calls that result in the return structure that
is normally written to user space being shunted off to user
specified kernel memory instead.
For the immediate repair, detect and deny suspicious accesses to
the write API.
For long term, update the user space libraries and the kernel API
to something that doesn't present the same security vulnerabilities
(likely a structured ioctl() interface).
The impacted uAPI interfaces are generally only available if
hardware from drivers/infiniband is installed in the system.
Reported-by: Jann Horn <jann@thejh.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[ Expanded check to all known write() entry points ]
Cc: stable@vger.kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
call_send is used to determine whether to send immediately or schedule
a send for later. The current logic in rdmavt is inverted and has a
negative impact on the latency of the hfi1 and qib drivers. Fix this
regression by correctly calling send immediately when call_send is set.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch fix spelling typos in printk from various part
of the codes.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
fix spelling mistake, argumant -> argument
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Minor overlapping changes in the conflicts.
In the macsec case, the change of the default ID macro
name overlapped with the 64-bit netlink attribute alignment
fixes in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_start_xmit never returns it to stack, but nes_nic_send helper used it if
skb could not be queued to hardware. Switch to bool instead.
Cc: <linux-rdma@vger.kernel.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In c4iw_drain_sq/rq(), if the particular queue is already empty
then don't block.
Fixes: ce4af14d94aa ('iw_cxgb4: add queue drain functions')
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The IWCM uses ibdev.iwcm->ifname for registration with the iwarp
port map daemon. But iw_cxgb3 did not initialize this field which
causes intermittent registration failures based on the contents of the
uninitialized memory.
Fixes: c1340e8aa6 ("iw_cxgb3: support for iWARP port mapping")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The IWCM uses ibdev.iwcm->ifname for registration with the iwarp
port map daemon. But iw_cxgb4 did not initialize this field which
causes intermittent registration failures based on the contents of the
uninitialized memory.
Fixes: 170003c894 ("iw_cxgb4: remove port mapper related code")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The drain_rq function expects a normal receive qp to drain. A qp can
only have either a normal rq or an srq. If there is an srq, there
is no rq to drain. Until the API supports draining SRQs, simply
skip draining the rq when the qp has an srq attached.
Fixes: 765d67748b ("IB: new common API for draining queues")
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
For set/query MTU port firmware commands the MTU field
is 16 bits, here I changed all the "int mtu" parameters
of the functions wrapping those firmware commands to be u16.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we fail to find the default gid index, we can't continue
processing in this routine or else we will pass a negative
index to later routines resulting in invalid memory access
attempts and a kernel oops.
Fixes: 03db3a2d81 (IB/core: Add RoCE GID table management)
Signed-off-by: Doug Ledford <dledford@redhat.com>
When we fail to find the default gid index, we can't continue
processing in this routine or else we will pass a negative
index to later routines resulting in invalid memory access
attempts and a kernel oops.
Fixes: 03db3a2d81 (IB/core: Add RoCE GID table management)
Signed-off-by: Doug Ledford <dledford@redhat.com>
Rename SCSI_MAX_SG_SEGMENTS to SG_CHUNK_SIZE, which means the amount
we fit into a single scatterlist chunk.
Rename SCSI_MAX_SG_CHAIN_SEGMENTS to SG_MAX_SEGMENTS.
Will move these 2 generic definitions to scatterlist.h later.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Bart Van Assche <bart.vanassche@sandisk.com> (for ib_srp changes)
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On larger installations it is useful to disable automatic LUN scanning,
and only add the required LUNs via udev rules. This can speed up bootup
dramatically.
This patch introduces a new scan module parameter value 'manual', which
works like 'none', but can be overridden by setting the 'rescan' value
from scsi_scan_target to 'SCSI_SCAN_MANUAL'. And it updates all
relevant callers to set the 'rescan' value to 'SCSI_SCAN_MANUAL' if
invoked via the 'scan' option in sysfs.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit 0fd10721fe.
That patch causes the ib_srpt driver to crash as soon as the first SCSI
command is received:
kernel BUG at drivers/infiniband/ulp/srpt/ib_srpt.c:1439!
invalid opcode: 0000 [#1] SMP
Workqueue: target_completion target_complete_ok_work [target_core_mod]
RIP: srpt_queue_response+0x437/0x4a0 [ib_srpt]
Call Trace:
srpt_queue_data_in+0x9/0x10 [ib_srpt]
target_complete_ok_work+0x152/0x2b0 [target_core_mod]
process_one_work+0x197/0x480
worker_thread+0x49/0x490
kthread+0xea/0x100
ret_from_fork+0x22/0x40
Aside from the crash, the shortcomings of that patch are as follows:
- It makes the ib_srpt driver use I/O contexts allocated by
transport_alloc_session_tags() but it does not initialize these I/O
contexts properly. All the initializations performed by
srpt_alloc_ioctx() are skipped.
- It swaps the order of the send ioctx allocation and the transition to
RTR mode which is wrong.
- The amount of memory that is needed for I/O contexts is doubled.
- srpt_rdma_ch.free_list is no longer used but is not removed.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matan Barak