GEN > 9 require transition WM to be programmed if IPC is enabled.
This patch calculates & enable transition WM for supported platforms.
If transition WM is enabled, Plane read requests are sent at high
priority until filling above the transition watermark, then the
requests are sent at lower priority until dropping below the level-0 WM.
The lower priority requests allow other memory clients to have better
memory access.
transition minimum is the minimum amount needed for trans_wm to work to
ensure the demote does not happen before enough data has been read to
meet the level 0 watermark requirements.
transition amount is configurable value. Higher values will
tend to cause longer periods of high priority reads followed by longer
periods of lower priority reads. Tuning to lower values will tend to
cause shorter periods of high and lower priority reads.
Keeping transition amount to 10 in this patch, as suggested by HW team.
Changes since V1:
- Address review comments from Maarten
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170817134529.2839-4-mahesh1.kumar@intel.com
Plane configuration parameters doesn't change for each WM-level
calculation. Currently we compute same parameters 8 times for each
wm-level.
This patch optimizes it by calculating these parameters in beginning
& reuse during each level-wm calculation.
Changes since V1:
- rebase on top of Rodrigo's series for CNL
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170817134529.2839-3-mahesh1.kumar@intel.com
Skip compressing 1 segment at the end of the frame,
avoid a pixel count mismatch nuke event when last active
pixel and dummy pixel has same color for Odd Plane
Width / Height.
For both platforms Gemini Lake and Cannon Lake.
v2: Use function-like macro and also use mask to clean
to make sure bit 11 is 0. (Suggested by Paulo).
v3: Add Display WA notation and also apply for GLK.
Both Forgotten on v2.
Using "GLK_" prefix since GLK came before CNL.
v4: Forgot to "|=" when moving directly macro to masked
val. (Noticed by Paulo.)
v5: Rebased on top of 0a46ddd57c ("drm/i915/cnp: Wa 1181:
Fix Backlight issue")
Cc: Imre Deak <imre.deak@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170905193013.31710-1-rodrigo.vivi@intel.com
This workaround fixes a CNL PCH bug when changing
backlight from a lower frequency to a higher frequency.
During random reboot cycles, display backlight seems to
be off/ dim for 2-3 mins.
The only functional change on this patch is to
set bit 13 of 0xC2020 for CNL PCH.
The rest of patch is organizing identation around
those bits definitions and re-organizing CFL workarounds.
v2: Only add the bit that matters without touching others
around (Jani).
Rebase on top of clock gating functions rename.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170831045223.3960-1-rodrigo.vivi@intel.com
No functional changes.
Our code was only a bit messy with mixed style there so
let's clean up a bit using the short codenames for the platforms.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170829052026.15038-1-rodrigo.vivi@intel.com
If we miss the current vblank because the gpu was busy, that may cause a
jitter as the frame rate temporarily drops. We try to limit the impact
of this by then boosting the GPU clock to deliver the frame as quickly
as possible. Originally done in commit 6ad790c0f5 ("drm/i915: Boost GPU
frequency if we detect outstanding pageflips") but was never forward
ported to atomic and finally dropped in commit fd3a40242e ("drm/i915:
Rip out legacy page_flip completion/irq handling").
One of the most typical use-cases for this is a mostly idle desktop.
Rendering one frame of the desktop's frontbuffer can easily be
accomplished by the GPU running at low frequency, but often exceeds
the time budget of the desktop compositor. The result is that animations
such as opening the menu, doing a fullscreen switch, or even just trying
to move a window around are slow and jerky. We need to respond within a
frame to give the best impression of a smooth UX, as a compromise we
instead respond if that first frame misses its goal. The result should
be a near-imperceivable initial delay and a smooth animation even
starting from idle. The cost, as ever, is that we spend more power than
is strictly necessary as we overestimate the required GPU frequency and
then try to ramp down.
This of course is reactionary, too little, too late; nevertheless it is
surprisingly effective.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102199
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170817123706.6777-1-chris@chris-wilson.co.uk
Tested-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
This bit enables hardware that will change the approximation used for distances
calculations for AA wide lines so that they are rendered more accurately.
The default value for this bit leaves the legacy behavior. There is no good
reason to not enable the new approximation except if comparing to previous GEN
rendered images.
v2: Rebase
v3: Fix author.
Rebased by Rodrigo who also added a comment as suggested by Oscar.
Since it is surrounded by Workarounds let's just add a comment to
make clear it is not an Wa.
Cc: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170815231651.975-4-rodrigo.vivi@intel.com
Let's inherit workarounds from previous platforms that
according to wa_database and BSpec are still valid for
Cannonlake.
v2: Add missed workarounds.
v3: Rebase
v4: Remove bad chunk that was added to rc6 disable. (Ander)
Also remove A0 W/a that are not needed anymore.
v5: Rebase on top of CFL.
v6: Remove empty gen9_init_perctx_bb and gen9_init_indirectctx_bb
since they don't carry any gen10 related W/a. (by Oscar).
Also Remove A0 exclusive workaround.
v7: Remove more A0 exclusive workarounds. As pointed out by Oscar
many workarounds were changed to be A0 only so let's remove
them.
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170815231651.975-1-rodrigo.vivi@intel.com
They're slightly different than the gen 9 calculations.
v2: Remove TODO comment. Code matches recent spec.
v3: Rebase on top of latest skl code using new fp16.16 and
fixing a logic issue. Auto rebase bot has apparently
made some bad decisions that changed the logic of the
code. (Noticed by Manesh, updated by Rodrigo).
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170811233825.32083-1-rodrigo.vivi@intel.com
Gen 10 is just like Gen 9, so let's consider that all the future
platforms are going to be like gen 9 instead of being like gen8-.
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170809205248.11917-4-rodrigo.vivi@intel.com
A previous commit added CNL to intel_has_sagv(), but forgot to adjust
the SAGV block time to gen 10 platforms.
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170809205248.11917-3-rodrigo.vivi@intel.com
For now inherit from previous platforms.
v2: Rebase on top of CFL.
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170809205248.11917-2-rodrigo.vivi@intel.com
Gen 10 should use the exact same code as Gen 9, so change the check to
take this into consideration, and also assume that future platforms
will run this code.
Also add a MISSING_CASE(), just in case we do something wrong, instead
of silently failing.
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170809205248.11917-1-rodrigo.vivi@intel.com
SKL+ display engine can scan out certain kinds of compressed surfaces
produced by the render engine. This involved telling the display engine
the location of the color control surfae (CCS) which describes
which parts of the main surface are compressed and which are not. The
location of CCS is provided by userspace as just another plane with its
own offset.
Add the required stuff to validate the user provided AUX plane metadata
and convert the user provided linear offset into something the hardware
can consume.
Due to hardware limitations we require that the main surface and
the AUX surface (CCS) be part of the same bo. The hardware also
makes life hard by not allowing you to provide separate x/y offsets
for the main and AUX surfaces (excpet with NV12), so finding suitable
offsets for both requires a bit of work. Assuming we still want keep
playing tricks with the offsets. I've just gone with a dumb "search
backward for suitable offsets" approach, which is far from optimal,
but it works.
Also not all planes will be capable of scanning out compressed surfaces,
and eg. 90/270 degree rotation is not supported in combination with
decompression either.
This patch may contain work from at least the following people:
* Vandana Kannan <vandana.kannan@intel.com>
* Daniel Vetter <daniel@ffwll.ch>
* Ben Widawsky <ben@bwidawsk.net>
v2: Deal with display workarounds 0390, 0531, 1125 (Paulo)
v3: Pretend CCS tiles are regular 128 byte wide Y tiles (Jason)
Put the AUX register defines to the correct place
Fix up the slightly bogus rotation check
v4: Use I915_WRITE_FW() due to plane update locking changes
s/return -EINVAL/goto err/ in intel_framebuffer_init()
Eliminate a bunch hardcoded numbers in CCS code
v5: (By Ben)
conflict resolution +
- res_blocks += fixed_16_16_to_u32_round_up(y_tile_minimum);
+ res_blocks += fixed16_to_u32_round_up(y_tile_minimum);
v6: (daniels) Fix botched commit message.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Ville Syrjä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Stone <daniels@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170801165817.7063-1-ben@bwidawsk.net
This WA is required when decoupled frequencies for slice and unslice
are enabled. This disables DOP clock gating for skl.
v2: enable the WA for all gen9 platforms (not just for SKL GT4 where
the hang issue is originally reported) to avoid rare hangs (David)
v3: as per WaDatabase, enable it only for SKL (Rodrigo)
Cc: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Praveen Paneri <praveen.paneri@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1501781530-8186-1-git-send-email-praveen.paneri@intel.com
If we fail at punit communication, include both the mbox address and the
value we tried to write so that we can identify the invalid sequence.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170728085022.1586-1-chris@chris-wilson.co.uk
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ddb_allocation && ddb_allocation / blocks_per_line >= 1 is the same
as ddb_allocation >= blocks_per_line, so use the latter to simplify
this.
This fixes the following compiler warning:
drivers/gpu/drm/i915/intel_pm.c:4467]: (warning) Comparison of a
boolean expression with an integer other than 0 or 1.
Changes since v1:
- Rebase, was missing the changes to the macro names.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: d555cb5827 ("drm/i915/skl+: use linetime latency if ddb size is not available")
Cc: "Mahesh Kumar" <mahesh1.kumar@intel.com>
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: David Binderman <dcb314@hotmail.com>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.13-rc1+
Link: http://patchwork.freedesktop.org/patch/msgid/20170717120230.2023-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
height of plane was require to swap width/height in case of 90/270
rotation. Now src structure contains already swapped values, So we
don't have to calculate height of the plane.
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170705143154.32132-6-mahesh1.kumar@intel.com
This patch make naming of fixed-point wrappers consistent
operation_<any_post_operation>_<1st operand>_<2nd operand>
also shorten the name for fixed_16_16 to fixed16
s/u32_to_fixed_16_16/u32_to_fixed16
s/fixed_16_16_to_u32/fixed16_to_u32
s/fixed_16_16_to_u32_round_up/fixed16_to_u32_round_up
s/min_fixed_16_16/min_fixed16
s/max_fixed_16_16/max_fixed16
s/mul_u32_fixed_16_16/mul_u32_fixed16
s/fixed_16_16_div/div_fixed16
Changes Since V1:
- Split the patch in more logical patches (Maarten)
Changes Since V2:
- Rebase
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170705143154.32132-4-mahesh1.kumar@intel.com
This patch combines fixed_16_16_div & fixed_16_16_div_u64 wrappers.
And new fixed_16_16_div wrapper always performs division operation in
u64 internally, to avoid any data loss which was happening in earlier
version of wrapper.
earlier wrapper was converting u32 to fixed16 in 32 bit so we were
losing 16-MSB data.
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170705143154.32132-3-mahesh1.kumar@intel.com
[mlankhorst: Fix typo in commit message.]
Once a client has requested a waitboost, we keep that waitboost active
until all clients are no longer waiting. This is because we don't
distinguish which waiter deserves the boost. However, with the advent of
fence signaling, the signaler threads appear as waiters to the RPS
interrupt handler. So instead of using a single boolean to track when to
keep the waitboost active, use a counter of all outstanding waitboosted
requests.
At this point, I have removed all vestiges of the rate limiting on
clients. Whilst this means that compositors should remain more fluid,
it also means that boosts are more prevalent. See commit b29c19b645
("drm/i915: Boost RPS frequency for CPU stalls") for a longer discussion
on the pros and cons of both approaches.
A drawback of this implementation is that it requires constant request
submission to keep the waitboost trimmed (as it is now cancelled when the
request is completed). This will be fine for a busy system, but near
idle the boosts may be kept for longer than desired (effectively tens of
vblanks worstcase) and there is a reliance on rc6 instead.
v2: Remove defunct rps.client_lock
Reported-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170628123548.9236-1-chris@chris-wilson.co.uk
This reverts commit bb9d85f6e9.
New ddb allocation algorithm is a show stopper on my SKL system.
Besides not be able to get external DP 4k@60 (through USB type C),
It fully hang my screen when unplugging the USB type C.
Bugzilla: https://patchwork.freedesktop.org/patch/161571/
Fixes: bb9d85f6e9 ("drm/i915/skl: New ddb allocation algorithm")
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497376350-3400-1-git-send-email-rodrigo.vivi@intel.com
The whole Display engine for Coffee Lake is pretty much
identical to the Kabylake. For this reason let's reuse
all display related production workardounds here even though
CFL is not explicit listed at Display workarounds page at Spec.
v2: moved intel_pm.c chunck to this patch in order to address
all display related w/a in a single place.
Cc: Arthur Runyan <arthur.j.runyan@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496937000-8450-3-git-send-email-rodrigo.vivi@intel.com
skl_check_plane_surface() already rotates the clipped plane source
coordinates to match the scanout direction because that's the way
the GTT mapping is set up. Thus we no longer need to rotate the
coordinates in the watermark code.
For cursors we use the non-clipped coordinates which are not rotated
appropriately, but that doesn't actually matter since cursors don't
even support 90/270 degree rotation.
v2: Resolve conflicts from SKL+ wm rework
Cc: stable@vger.kernel.org
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: b63a16f6cd ("drm/i915: Compute display surface offset in the plane check hook for SKL+")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170331180056.14086-3-ville.syrjala@linux.intel.com
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Seems that GLK has a dotclock that's twice the display clock.
skl_max_scale checks for IS_GEMINILAKE, so perform the same check here.
While at it, change the DRM_ERROR to DEBUG_KMS.
Fixes: 73b0ca8ec7 ("drm/i915/skl+: consider max supported plane pixel
rate while scaling")
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601103413.7037-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
A display resolution is only supported if it meets all the restrictions
below for Maximum Pipe Pixel Rate.
The display resolution must fit within the maximum pixel rate output
from the pipe. Make sure that the display pipe is able to feed pixels at
a rate required to support the desired resolution.
For each enabled plane on the pipe {
If plane scaling enabled {
Horizontal down scale amount = Maximum[1, plane horizontal size /
scaler horizontal window size]
Vertical down scale amount = Maximum[1, plane vertical size /
scaler vertical window size]
Plane down scale amount = Horizontal down scale amount *
Vertical down scale amount
Plane Ratio = 1 / Plane down scale amount
}
Else {
Plane Ratio = 1
}
If plane source pixel format is 64 bits per pixel {
Plane Ratio = Plane Ratio * 8/9
}
}
Pipe Ratio = Minimum Plane Ratio of all enabled planes on the pipe
If pipe scaling is enabled {
Horizontal down scale amount = Maximum[1, pipe horizontal source size /
scaler horizontal window size]
Vertical down scale amount = Maximum[1, pipe vertical source size /
scaler vertical window size]
Note: The progressive fetch - interlace display mode is equivalent to a
2.0 vertical down scale
Pipe down scale amount = Horizontal down scale amount *
Vertical down scale amount
Pipe Ratio = Pipe Ratio / Pipe down scale amount
}
Pipe maximum pixel rate = CDCLK frequency * Pipe Ratio
In this patch our calculation is based on pipe downscale amount
(plane max downscale amount * pipe downscale amount) instead of Pipe
Ratio. So,
max supported crtc clock with given scaling = CDCLK / pipe downscale.
Flip will fail if,
current crtc clock > max supported crct clock with given scaling.
Changes since V1:
- separate out fixed_16_16 wrapper API definition
Changes since V2:
- Fix buggy crtc !active condition (Maarten)
- use intel_wm_plane_visible wrapper as per Maarten's suggestion
Changes since V3:
- Change failure return from ERANGE to EINVAL
Changes since V4:
- Rebase based on previous patch changes
Changes since V5:
- return EINVAL instead of continue (Maarten)
Changes since V6:
- Improve commit message
- Address review comment
Changes since V7:
- use !enable instead of !active
- rename config variable for consistency (Maarten)
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170526151546.25025-4-mahesh1.kumar@intel.com
This patch implements new DDB allocation algorithm as per HW team
recommendation. This algo takecare of scenario where we allocate less DDB
for the planes with lower relative pixel rate, but they require more DDB
to work.
It also takes care of enabling same watermark level for each
plane in crtc, for efficient power saving.
Changes since v1:
- Rebase on top of Paulo's patch series
Changes since v2:
- Fix the for loop condition to enable WM
Changes since v3:
- Fix crash in cursor i-g-t reported by Maarten
- Rebase after addressing Paulo's comments
- Few other ULT fixes
Changes since v4:
- Rebase on drm-tip
- Added separate function to enable WM levels
Changes since v5:
- Fix a crash identified in skl-6770HQ system
Changes since v6:
- Address review comments from Matt
Changes since v7:
- Fix failure return in skl_compute_plane_wm (Matt)
- fix typo
Changes since v8:
- Always check cursor wm enable irrespective of total_data_rate
Changes since v9:
- fix typo
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601055918.4601-1-mahesh1.kumar@intel.com
On some systems there can be a race condition in which no crtc state is
added to the first atomic commit. This results in all crtc's having a
null DDB allocation, causing a FIFO underrun on any update until the
first modeset.
Changes since v1:
- Do not take the connection_mutex, this is already done below.
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Inspired-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 98d39494d3 ("drm/i915/gen9: Compute DDB allocation at atomic
check time (v4)")
Cc: <stable@vger.kernel.org> # v4.8+
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170531154236.27180-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
This patch make changes to use linetime latency if allocated
DDB size during plane watermark calculation is not available.
linetime is the time, display engine takes to fetch one line worth of
pixels with given pixel clock rate.
This is required to implement new DDB allocation algorithm.
In New Algorithm DDB is allocated based on WM values, because of which
number of DDB blocks will not be available during WM calculation,
So this "linetime latency" is suggested by SV/HW team to be used during
switch-case for WM blocks selection.
linetime latency us = pipe horizontal total pixels/adjusted pixel rate MHz
Changes since v1:
- Rebase on top of Paulo's patch series
Changes since v2:
- Fix if-else condition (pointed by Maarten)
Changes since v3:
- Use common function for timetime_us calculation (Paulo)
- rebase on drm-tip
Changes since v4:
- Use consistent name for fixed_point operation
Changes since v5:
- Improve commit message
- rename skl_get_linetime_us to intel_get_linetime_us
- fix watermark result selection (Matt)
Signed-off-by: "Mahesh Kumar" <mahesh1.kumar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170517115831.13830-11-mahesh1.kumar@intel.com
Instead of iterating over planes & wm levels in a single function use
skl_compute_wm_level function to interate over WM levels.
Change name of function to skl_compute_wm_levels (Matt).
These changes are to clean-up WM code & will help in making only new
ddb algorithm related changes in later patch in series.
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170517115831.13830-10-mahesh1.kumar@intel.com
This patch cleanup/reorganises the watermark calculation functions.
This patch make use of already available macro
"drm_atomic_crtc_state_for_each_plane_state" to walk through
plane_state list instead of calculating plane_state in function itself.
This restructuring will help later patch for new DDB allocation
algorithm to do only algo related changes.
Changes from V1:
- split the patch in two parts as per Matt's comment
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170517115831.13830-9-mahesh1.kumar@intel.com
DDB minimum requirement of crtc configuration (cumulative of all the
enabled planes in crtc) may exceed the allocated DDB for crtc/pipe.
This patch make changes to fail the flip/ioctl if minimum requirement
for pipe exceeds the total ddb allocated to the pipe.
Previously it succeeded but making alloc_size a negative value. Which
will make subsequent calculations for plane ddb allocation bogus & may
lead to screen corruption or system hang.
Changes from V1:
- Improve commit message as per Ander's comment
- Remove extra parentheses (Ander)
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170517115831.13830-8-mahesh1.kumar@intel.com
We are already doing memset of ddb structure at the begining of skl_allocate_pipe_ddb
function, No need to again do a memset.
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170517115831.13830-7-mahesh1.kumar@intel.com
Fail the flip if no FB is present but plane_state is set as visible.
Above is not a valid combination so instead of continue fail the flip.
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170517115831.13830-6-mahesh1.kumar@intel.com
This patch make changes to calculate adjusted plane pixel rate &
plane downscale amount using fixed_point functions available.
This patch will give uniformity in code, & will help to avoid mixing of
32bit uint32_t variable for fixed-16.16 with fixed_16_16_t variables in
later patch in the series.
Changes from V1:
- Rebase based on wrapper name change
- Remove unnecessary comment
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170517115831.13830-5-mahesh1.kumar@intel.com
fixed_16_16_div_round_up(_u64), wrapper for fixed_16_16 division
operation don't really round_up the result. Wrapper round_up only the
fraction part of the result to make it 16-bit.
This patch eliminates round_up keyword from the wrapper.
Later patch will introduce the new wrapper to do rounding-off the result
and give unt32_t output to cleanup mix use of fixed_16_16_t & uint32_t
variables.
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170517115831.13830-2-mahesh1.kumar@intel.com
I don't see why we couldn't use the HPLL watermarks on g4x. So let's
enable them. Let's assume a 35 usec memory latency for the HPLL mode.
That's roughly what PNV uses.
Based on the behaviour of the ELK box I have 35 usec is probably
overkill. Actually all the current latency values used seem overkill as
I can reduce them pretty drastically before I start to see underruns.
But let's play things a bit safe for now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-14-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Implement proper two stage watermark programming for g4x. As with
other pre-SKL platforms, the watermark registers aren't double
buffered on g4x. Hence we must sequence the watermark update
carefully around plane updates.
The code is quite heavily modelled on the VLV/CHV code, with some
fairly significant differences due to the different hardware
architecture:
* g4x doesn't use inverted watermark values
* CxSR actually affects the watermarks since it controls memory self
refresh in addition to the max FIFO mode
* A further HPLL SR mode is possible with higher memory wakeup
latency
* g4x has FBC2 and so it also has FBC watermarks
* max FIFO mode for primary plane only (cursor is allowed, sprite is not)
* g4x has no manual FIFO repartitioning
* some TLB miss related workarounds are needed for the watermarks
Actually the hardware is quite similar to ILK+ in many ways. The
most visible differences are in the actual watermakr register
layout. ILK revamped that part quite heavily whereas g4x is still
using the layout inherited from earlier platforms.
Note that we didn't previously enable the HPLL SR on g4x. So in order
to not introduce too many functional changes in this patch I've not
actually enabled it here either, even though the code is now fully
ready for it. We'll enable it separately later on.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-13-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The documentation I've seen doesn't actually specify which watermarks
need the TLB miss w/a. Currently we only apply the w/a to the normal
watermarks for both primary and cursor planes. Since the documentation
doesn't explicitly say anything I'm going to assume that the w/a should
equally apply to the SR/HPLL watermarks. So let's do that.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-12-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
All platforms until SKL compute their watermarks essentially
using the same method1/small buffer and method2/large buffer
formulas. Most just open code it in slightly different ways.
Let's pull it all into common helpers. This makes it a little
easier to spot the actual differences.
While at it try to add some docs explainign what the formulas
are trying to do.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-11-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The g4x watermark TLB miss workaround requires that we bump up the
watermark by the difference between 8 full lines and the FIFO size.
Unfortunately the way we compute it at the moment ignores the size
of the pixels. The code also used the primary plane width as the
cursor width when computing the TLB miss w/a for the cursor.
Let's fix both problems.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-9-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The watermark code for the old platforms (g4x and older) uses the
primary plane cpp when computing cursor watermarks. To keep the fix
simple let's just hardcode cpp=4 for the cursor on those platforms
since that's all we support.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-8-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Rename the VLV/CHV max_level->num_levels helper to have an intel_
prefix since it's not VLV/CHV specific and I'll want to use it on
other platforms as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-4-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Seeing the display FIFO sizes at driver load time doesn't really provide
anything useful for us, so let's just drop the debug message. One can
always use eg. intel_watermarks to dump out the hardware settings prior
to loading the driver.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-3-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Since the sandybridge_pcode_read() may be called from
skl_pcode_request() inside an atomic context (with preempt disabled), we
should avoid hitting any sleeping paths. Currently is being called with
a 500ms timeout, irrespective of being inside an atomic context or not.
This is reduced down to 500us to play nice with the atomic context, and
that appears to be sufficient to keep BAT happy (we have a DRM_ERROR
should it timeout), i.e. we do not see any 500us pcode timeouts for
normal use. So leave it as a pure spin without having to introduce new
code paths to separate atomic/normal contexts.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170411101340.31994-4-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
The VLV/CHV watermark calculation is really interested in the hardware
plane type rather than the plane type (which is more of a software
concept). Let's check plane->id rather plane->type.
No functional changes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303151928.23053-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
We can't sometimes use these macros in other headers due to
include and definition order. As i915_utils.h already contains
other helper macros move these macros there.
v2: checkpatch cleanup for WARN() macro.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170328084513.174200-1-michal.wajdeczko@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We have only 8bits of precise timestamps in which to complete our
upper/load reads, along with the switch between precision. This is not
always enough time to read the upper counter twice within the same time
slice, leading to hard lockups. Limit the number of times to prevent
an inifite loop (my fault for assuming we would have no trouble doing
the write + reads fast enough).
Fixes: 47c21d9a1a ("drm/i915: Extend vlv/chv residency resolution")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100377
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170324165418.7455-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Use intel_wm_plane_visible() to determine cursor visibility for SKL+
also. Previously SKL+ would check the actual visibility which now
conflicts with the assumptions in intel_legacy_cursor_update().
We also change SKL+ to compute the cursor watermarks based on the
unclipped cursor size, just as we do on all the other platforms.
Using the clipped size could now result in garbage results.
Testcase: igt/kms_chv_cursor_fail
Fixes: a5509abda4 ("drm/i915: Fix legacy cursor vs. watermarks for ILK-BDW")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100195
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170314151050.12194-2-ville.syrjala@linux.intel.com
Tested-by: Dorota Czaplejewicz <dorota.czaplejewicz@collabora.co.uk>
Tested-by: Jari Tahvanainen <jari.tahvanainen@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
All platforms that lack double buffered watermarks will need to
handle the legacy cursor updates in the same way. So let's extract the
logic to determine the plane visibility into a small helper. For
simplicity we'll make the function DTRT for any plane, but only apply
the special sauce for cursor planes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170314151050.12194-1-ville.syrjala@linux.intel.com
Tested-by: Dorota Czaplejewicz <dorota.czaplejewicz@collabora.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Before rc6 is initialised (after driver load or resume), the value inside
VLV_COUNTER_CONTROL is undefined so we cannot make an assertion that is
in HIGH_RANGE mode.
Fixes: 6b7f6aa75e ("drm/i915: Use coarse grained residency counter with byt")
Testcase: igt/drv_suspend/debugfs-reader
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170317125918.11351-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
The only time we need to emit a flush inside request emission is after
an execbuffer, for which we can use the full __i915_add_request(). All
other instances want the simpler i915_add_request() without flushing, so
remove the useless helper.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170317114709.8388-1-chris@chris-wilson.co.uk
Set byt rc residency counters high level as chv does by
default. We lose some accuracy on byt but we can do the calculation
without extra hw read on both platforms, as now they behave
identically in this respect.
v2: use ktime
v3: keep comparison u32 (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1489592584-10422-1-git-send-email-mika.kuoppala@intel.com
Vlv and chv residency counters are 40 bits in width.
With a control bit, we can choose between upper or lower
32 bit window into this counter.
Lets toggle this bit on and off on and read both parts.
As a result we can push the wrap from 13 seconds to 54
minutes.
v2: commit msg, loop readability, goto elimination (Chris)
v3: bug ref, divide outside runtime pm lock (Chris)
References: https://bugs.freedesktop.org/show_bug.cgi?id=94852
Reported-by: Len Brown <len.brown@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Change the granularity from milliseconds to microseconds
when returning rc6 residencies. This is in preparation
for increased resolution on some platforms.
v2: use 64bit div macro (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Plan is to make generic residency calculation utility
function for usage outside of sysfs. As a first step
move residency calculation into intel_pm.c
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Use I915_{READ,WRITE}_FW() for updating the DSPARB registers on
VLV/CHV. This is less expesive as we can grab the uncore.lock across
the entire sequence of reads and writes instead of each register
access grabbing it.
This also allows us to eliminate the dsparb lock entirely as the
uncore.lock now effectively protects the contents of the DSPARB
registers.
v2: Add a note that interrupts are already disabled (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170309154434.29303-6-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
On Baytrail, we manually calculate busyness over the evaluation interval
to avoid issues with miscaluations with RC6 enabled. However, it turns
out that the DOWN_EI interrupt generator is completely bust - it
operates in two modes, continuous or never. Neither of which are
conducive to good behaviour. Stop unmask the DOWN_EI interrupt and just
compute everything from the UP_EI which does seem to correspond to the
desired interval.
v2: Fixup gen6_rps_pm_mask() as well
v3: Inline vlv_c0_above() to combine the now identical elapsed
calculation for up/down and simplify the threshold testing
Fixes: 43cf3bf084 ("drm/i915: Improved w/a for rps on Baytrail")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.1+
Link: http://patchwork.freedesktop.org/patch/msgid/20170309211232.28878-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Add a tracepoint for observing changes in the cxsr state. The tracepoint
will dump out the frame and scanline counters for each pipe so that the
information can be compared with eg. plane update tracepoints.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-18-ville.syrjala@linux.intel.com
Add tracepoints for observing the WM/FIFO programming on VLV/CHV. When
compared with the plane and pipe update tracepoints this can be used
to verify that everything is performed in the right sequence.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-17-ville.syrjala@linux.intel.com
On VLV/CHV enabling sprite0 when sprite1 has already been enabled may
lead to an underrun. This only happens when sprite0 FIFO size is zero
prior to enabling it. Hence an effective workaround is to always
allocate at least one cacheline for sprite0 when sprite1 is active.
I've not observed this sort of failure during any other type of plane
enable/disable sequence.
v2: s/noninverted/raw/ for consistency with other platforms
Testcase: igt/kms_plane_blinker
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-14-ville.syrjala@linux.intel.com
Clear out the watermark for all disabled planes to 0. This is required
to avoid falsely thinking that the inherited watermarks are bogus in
case the watermark is actually higher than the FIFO size.
v2: s/noninverted/raw/ for consistency with other platforms
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-13-ville.syrjala@linux.intel.com
Remove crtc->wm.cxsr_allowed and just rely on crtc_state->disable_cxsr
instead. This was used only by vlv/chv to indicate whether to enable
cxsr in the wm computation. That doesn't really work anymore, and as far
as the optimal watermarks go we'll just consider the number of planes
and the current pipe, and for the intermediate watermarks we'll also
start to consider disable_cxsr which is set appropriately when planes
are being enabled/disabled.
We'll also flip over the crtc_state->wm.need_postvbl_update setup so
that it's the wm code that will set it. Previously the generic code set
it up, and then the wm code cleared it again if it thought it's not
needed after all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-11-ville.syrjala@linux.intel.com
Since the watermark registers arent double buffered on VLV/CHV, we'll
need to play around with intermediate watermarks same was as we do on
ILK-BDW.
The watermark registers on VLV/CHV contain inverted values, so to find
the intermediate watermark value we just take the minimum of the
active and optimal values. This also means that, unlike ILK-BDW,
there's no chance that we'd fail to find a working intermediate
watermarks. As long as both the active and optimal watermarks are valid
the intermediate watermarks will come out valid as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-10-ville.syrjala@linux.intel.com
Check whether anything relevant has actually change when we compute new
watermarks for each plane in the state. If the watermarks for no
primary/sprite planes changed we don't have to recompute the FIFO split
or reprogram the DSBARB registers. And even the cursor watermarks didn't
change we can skip the merge+invert step between all the planes on
the pipe as well.
v2: s/noninverted/raw/ for consistency with other platforms
v3: Drop duplicated vlv_get_fifo_size() call during init
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-9-ville.syrjala@linux.intel.com
Start computing the vlv/chv watermarks the atomic way, from the
.compute_pipe_wm() hook. We'll recompute the actual watermarks
for only planes that are part of the state, the other planes will
keep their watermark from the last time it was computed.
And the actual watermark programming will happen from the
.initial_watermarks() hook. For now we'll just compute the
optimal watermarks, and we'll hook up the intermediate
watermarks properly later.
The DSPARB registers responsible for the FIFO paritioning are
double buffered, so they will be programming from
intel_begin_crtc_commit().
v2: s/noninverted/raw/ for consistency with other platforms
s/vlv_plane_wm_set/vlv_raw_plane_wm_set/ for clarity
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-8-ville.syrjala@linux.intel.com
Let's compute the watermarks first and the FIFO size second. This way we
can make sure the FIFO split is the most accommodating to the watermarks.
Previously we could have potentially computed a FIFO split that couldn't
accommodate the PM2 watermarks simply due to a bad split even if the
total FIFO size would have been sufficient.
It'll also allow us to avoid recomputing the wms for all planes whenever
the FIFO split would change. Thus we don't have to add any extra planes
to the state when the FIFO needs to be repartitioned.
To help with this we'll keep around copies of the non-inverted
watermarks in the crtc state. For now that doesn't help too much, but
once we start to do the watermark computation only for the planes
that change we'll need the non-inverted values around for the other
planes.
v2: s/noninverted/raw/ for consistency with other platforms
Fix the memset() of the "raw" watermarks
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-7-ville.syrjala@linux.intel.com
Relocate the vlv/chv wm state to live under intel_crtc_state. Note
that for now this just behaves as a temporary storage. But it'll be
easier to conver the thing over to properly pre-computing the state
when it's already in the right place.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-5-ville.syrjala@linux.intel.com
Track the plane fifo sizes under intel_crtc instead of under each
intel_plane. Avoids looping over the planes in a bunch of places,
and later we'll move this tracking into the crtc state properly.
v2: Nuke intel_plane_wm_parameters (Maarten)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-3-ville.syrjala@linux.intel.com
assert_spin_locked() becomes an unconditionally compiled BUG_ON(),
adding debug code right into the heart of critical routines like
interrupt handlers.
text data bss dec hex
1296480 19944 2272 1318696 141f28 before (lockdep disabled)
1295984 19944 2272 1318200 141d38 after
1336261 21139 3208 1360608 14c2e0 before (lockdep enabled)
1339920 21139 3208 1364267 14d12b after
Small saving for release; hopefully more instructive in debug.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302132801.599-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
In order to make cursor updates actually safe wrt. watermark programming
we have to clear the legacy_cursor_update flag in the atomic state. That
will cause the regular atomic update path to do the necessary vblank
wait after the plane update if needed, otherwise the vblank wait would
be skipped and we'd feed the optimal watermarks to the hardware before
the plane update has actually happened.
To make the slow vs. fast path determination in
intel_legacy_cursor_update() a little simpler we can ignore the actual
visibility of the plane (which can only get computed once we've already
chosen out path) and instead we simply check whether the fb is being
set or cleared by the user. This means a fully clipped but logically
visible cursor will be considered visible as far as watermark
programming is concerned. We can do that for the cursor since it's a
fixed size plane and the clipped size doesn't play a role in the
watermark computation.
This should fix underruns that can occur when the cursor gets
enable/disabled or the size gets changed. Hopefully it's good enough
that only pure cursor movement and flips go through unthrottled.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Reported-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Fixes: f79f26921e ("drm/i915: Add a cursor hack to allow converting legacy page flip to atomic, v3.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170217150159.11683-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Tested-by: Rafael Ristovski <rafael.ristovski@gmail.com>
After
commit 2c7d0602c8
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Dec 5 18:27:37 2016 +0200
drm/i915/gen9: Fix PCODE polling during CDCLK change notification
there is still one report of the CDCLK-change request timing out on a
KBL machine, see the Reference link. On that machine the maximum time
the request took to succeed was 34ms, so increase the timeout to 50ms.
v2:
- Change timeout from 100 to 50 ms to maintain the current 50 ms limit
for atomic waits in the driver. (Chris, Tvrtko)
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=99345
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1487946730-17162-1-git-send-email-imre.deak@intel.com
Certain Baytrails, namely the 4 cpu core variants, have been
plaqued by spurious system hangs, mostly occurring with light loads.
Multiple bisects by various people point to a commit which changes the
reclocking strategy for Baytrail to follow its bigger brethen:
commit 8fb55197e6 ("drm/i915: Agressive downclocking on Baytrail")
There is also a review comment attached to this commit from Deepak S
on avoiding punit access on Cherryview and thus it was excluded on
common reclocking path. By taking the same approach and omitting
the punit access by not tweaking the thresholds when the hardware
has been asked to move into different frequency, considerable gains
in stability have been observed.
With J1900 box, light render/video load would end up in system hang
in usually less than 12 hours. With this patch applied, the cumulative
uptime has now been 34 days without issues. To provoke system hang,
light loads on both render and bsd engines in parallel have been used:
glxgears >/dev/null 2>/dev/null &
mpv --vo=vaapi --hwdec=vaapi --loop=inf vid.mp4
So far, author has not witnessed system hang with above load
and this patch applied. Reports from the tenacious people at
kernel bugzilla are also promising.
Considering that the punit access frequency with this patch is
considerably less, there is a possibility that this will push
the, still unknown, root cause past the triggering point on most loads.
But as we now can reliably reproduce the hang independently,
we can reduce the pain that users are having and use a
static thresholds until a root cause is found.
v3: don't break debugfs and simplification (Chris Wilson)
References: https://bugzilla.kernel.org/show_bug.cgi?id=109051
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: fritsch@xbmc.org
Cc: miku@iki.fi
Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
CC: Michal Feix <michal@feix.cz>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Deepak S <deepak.s@linux.intel.com>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.2+
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487166779-26945-1-git-send-email-mika.kuoppala@intel.com
The uncached mmio is sufficient to queue the mmio writes without raising
forcewake. The forced flush along with acquiring forcewake from the
posting read is not required for adjusting the RPS frequency.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170220094713.22874-3-chris@chris-wilson.co.uk
Reviewed-by: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
If intel_set_rps() is called whilst the hw is disabled, just store the
requested frequency (from the user) for application when we wake the hw
up.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170220094713.22874-2-chris@chris-wilson.co.uk
Reviewed-by: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Instead of having each back-end provide identical guards, just have a
singular set in intel_set_rps() to verify that the caller is obeying the
rules.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170220094713.22874-1-chris@chris-wilson.co.uk
Currently we apply the jump to rpe if we are below it and the GPU needs
more power. For some GPUs, the rpe is 75% of the maximum range causing
us to dramatically overshoot low power applications *and* unable to
reach the low frequency that can most efficiently deliver their
workload.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210150348.22146-3-chris@chris-wilson.co.uk
Reviewed-by: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
When the RPS tuning was applied to Baytrail, in commit 8fb55197e6
("drm/i915: Agressive downclocking on Baytrail"), concern was given that
it might cause Cherryview excess wakeups of the common power well.
However, the static thresholds perform poorly for Kodi, and the GPU is
unable to deliver the video frames on time. Enabling the dynamic, finer
thresholds used on all other platforms (including Skylake and Broxton
that also have the same multiple powerwell concerns) allows the GPU to
pick a more appropriate frequency and not drop frames.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210150348.22146-1-chris@chris-wilson.co.uk
Reviewed-by: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
With latest Punit FW, vgg input voltag drop falling to minimum is fixed.
So reverting the WA patch & moving to turbo freq opreation range to [RPn -> RP0]
This is not a 1:1 revert of the commit 5b7c91b78b.
You can refer to commit 5b5929cbe3 ("drm/i915/chv: remove
pre-production hardware workarounds") as the reason for the discrepancy
commit 5b7c91b78b
Author: Deepak S <deepak.s@linux.intel.com>
Date: Sat May 9 18:15:46 2015 +0530
drm/i915/chv: Set min freq to efficient frequency on chv
v2: Fix inconsistent return type. (Chris)
v3: drop pre-production hw case (Ville)
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471007801-86075-1-git-send-email-deepak.s@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
This workaround for BDW was incomplete as it also requires EUTC clock
gating to be disabled via UCGCTL1.
v2: read modify write UCGTL1 in broadwell_init_clock_gating (Ville)
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170212133252.20990-1-robert@sixbynine.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The current dev_cdclk vs. cdclk vs. atomic_cdclk_freq is quite a mess.
So here I'm introducing the "actual" and "logical" naming for our
cdclk state. "actual" is what we'll bash into the hardware and "logical"
is what everyone should use for state computaion/checking and whatnot.
We'll track both using the intel_cdclk_state as both will need other
differing parameters than just the actual cdclk frequency.
While doing that we can at the same time unify the appearance of the
.modeset_calc_cdclk() implementations a little bit.
v2: Commit dev_priv->cdclk.actual since that already has the
new state by the time .modeset_commit_cdclk() is called.
v3: s/locical/logical/ and improve the docs a bit
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170120182205.8141-9-ville.syrjala@linux.intel.com
Rather than recomputing the pipe pixel rate on demand everywhere, let's
just stick the precomputed value into the crtc state.
v2: Rebase due to min_pixclk[] code movement
Document the new pixel_rate struct member (Ander)
Combine vlv/chv with bdw+ in intel_modeset_readout_hw_state()
v3: Fix typos in commit message (David)
Cc: Ander Conselvan De Oliveira <conselvan2@gmail.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126195031.32343-1-ville.syrjala@linux.intel.com
Kumar, Mahesh