For IBoE, SLs 0-7 are mapped to Ethernet 802.1Q user priority bits
(pbits) which are part of the VLAN tag, SLs 8-15 are reserved.
Under Ethernet, the ConnectX firmware treats (decode/encode) the four
bit SL field in various constructs such as QPC / UD WQE / CQE as PPP0
and not as 0PPP. This correlates well to the fact that within the
vlan tag the pbits are located in bits 15-13 and not 12-14.
The current code wasn't consistent around that area - the
encoding was correct for the IBoE QPC.path.schedule_queue field,
but was wrong for IBoE CQEs and when MLX header was built.
These inconsistencies resulted in wrong SL <--> wire 802.1Q pbits
mapping, which is fixed by using SL <--> PPP0 all around the place.
Signed-off-by: Oren Duer <oren@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There's no need to set the vlan-related fields in an IBoE send WQE
control segment:
- the vlan to be used by a UD QP is set in the datagram segment.
- for GSI (CM) QP, all the headers down to 8021q and MAC are built by
the software anyway.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Support the creation of XRC INI and TGT QPs. To handle the case where
a CQ or PD is not provided, we allocate them internally with the xrcd.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Allocate flow counter per Ethernet/IBoE port, and attach this counter
to all the QPs created on that port. Based on patch by Eli Cohen
<eli@mellanox.co.il>.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We must fully update the control segment before marking it as valid,
so that hardware doesn't start executing it before we're ready.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Move VLAN control bit setting to before wmb(). - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch allows IBoE traffic to be encapsulated in 802.1Q tagged
VLAN frames. The VLAN tag is encoded in the GID and derived from it
by a simple computation.
The netdev notifier callback is modified to catch VLAN device
addition/removal and the port's GID table is updated to reflect the
change, so that for each netdevice there is an entry in the GID table.
When the port's GID table is exhausted, GID entries will not be added.
Only children of the main interfaces can add to the GID table; if a
VLAN interface is added on another VLAN interface (e.g. "vconfig add
eth2.6 8"), then that interfaces will not add an entry to the GID
table.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add 802.1q VLAN support to IBoE. The VLAN tag is encoded within the
GID derived from a link local address in the following way:
GID[11] GID[12] contain the VLAN ID when the GID contains a VLAN.
The 3 bits user priority field of the packets are identical to the 3
bits of the SL.
In case of rdma_cm apps, the TOS field is used to generate the SL
field by doing a shift right of 5 bits effectively taking to 3 MS bits
of the TOS field.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for IBoE to mlx4_ib. The bulk of the code is handling the
new address vector fields; mlx4 needs the MAC address of a remote node
to include it in a WQE (for datagrams) or in the QP context (for
connected QPs). Address resolution is done by assuming all unicast
GIDs are either link-local IPv6 addresses.
Multicast group attach/detach needs to update the NIC's multicast
filters; but since attaching a QP to a multicast group can be done
before the QP is bound to a port, for IBoE we need to keep track of
all multicast groups that a QP is attached too before it transitions
from INIT to RTR (since it does not have a port in the INIT state).
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Many things cleaned up and otherwise monkeyed with; hope I didn't
introduce too many bugs. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for packing IBoE packet headers.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Clean up and fix ib_ud_header_init() a bit. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for masked atomic operations (masked compare and swap,
masked fetch and add).
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
ib_ud_header_init() first clears header and then fills up the various
fields. Later on, it tests header->immediate_present, which it has
already cleared, so the condition is always false. Fix this by adding
an immediate_present parameter and setting header->immediate_present
as is done with grh_present. Also remove unused calculation of
header_len.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
struct ib_qp already holds a pointer to the ib device. No need to dive to the
hw device object to retrieve it.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In mlx4_ib_post_recv(), we should check the queue for overflow using
recv_cq instead of send_cq (current code looks like a copy-and-paste
mistake).
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Current code has a limitation: an LSO header is not allowed to cross a
64 byte boundary. This patch removes this limitation by setting the
WQE RR for large headers thus allowing LSO headers of any size. The
extra buffer reserved for MLX4_IB_QP_LSO QPs has been doubled, from 64
to 128 bytes, assuming this is reasonable upper limit for header
length. Also, this patch will cause IB_DEVICE_UD_TSO to be set only
for HCA FW versions that set MLX4_DEV_CAP_FLAG_BLH; e.g. FW version
2.6.000 and higher.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is no such flag DE - the field is reserved and should be zero.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mlx4_ib_lock_cqs()/mlx4_ib_unlock_cqs() are helper functions that
lock/unlock both CQs attached to a QP in the proper order to avoid
AB-BA deadlocks. Annotate this so sparse can understand what's going
on (and warn us if we misuse these functions).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ConnectX Programmer's Reference Manual states that the "SO" bit
must be set when posting Fast Register and Local Invalidate send work
requests. When this bit is set, the work request will be executed
only after all previous work requests on the send queue have been
executed. (If the bit is not set, Fast Register and Local Invalidate
WQEs may begin execution too early, which violates the defined
semantics for these operations)
This fixes the issue with NFS/RDMA reported in
<http://lists.openfabrics.org/pipermail/general/2009-April/059253.html>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The low-level mlx4 driver modified the page-list addresses for fast
register work requests post send to big-endian, and set a "present"
bit. This caused problems later when the consumer attempted to unmap
the pages using the page-list (using the list addresses which were
assumed to be still in CPU-endian order). Fix the mlx4 driver to
allocate two buffers and use a private buffer for the hardware-format
bus addresses.
This patch fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1571>,
an NFS/RDMA server crash. The cause of the crash was found by Vu Pham
of Mellanox. The fix is along the lines suggested by Steve Wise in
comment #21 in bug 1571.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The base versions handle constant folding just fine, use them
directly. The replacements are OK in the include/ files as they are
not exported to userspace so we don't need the __ prefixed versions.
This patch does not affect code generation at all.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The current work request posting code writes the LSO segment before
writing any data segments. This leaves a window where the LSO segment
overwrites the stamping in one cacheline that the HCA prefetches
before the rest of the cacheline is filled with the correct data
segments. When the HCA processes this work request, a local
protection error may result.
Fix this by saving the LSO header size field off and writing it only
after all data segments are written. This fix is a cleaned-up version
of a patch from Jack Morgenstein <jackm@dev.mellanox.co.il>.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1383>.
Reported-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
To allow allocating an aligned range of consecutive QP numbers, add an
interface to reserve an aligned range of QP numbers and have the QP
allocation function always take a QP number.
This will be used for RSS support in the mlx4_en Ethernet driver and
also potentially by IPoIB RSS support.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set RLKEY bit in the HW context for kernel QPs so that kernel QPs can
use the reserved L_Key for memory reference.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Byte swap the addresses in the page list for fast register work requests
to big endian to match what the HCA expectx. Also, the addresses must
have the "present" bit set so that the HCA knows it can access them.
Otherwise the HCA will fault the first time it accesses the memory
region.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Current code limits the max message size to 2K for UD QPs, while MTU
might be as big as 4K. This patch sets the maximum message size to
4K, which is needed for UD to work correctly on fabrics with a 4K MTU.
Signed-off-by: Alex Naslednikov <xalex@mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Update existing Mellanox copyright lines to 2008, and add such lines
to files where they are missing.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for the following operations to mlx4 when device firmware
supports them:
- Send with invalidate and local invalidate send queue work requests;
- Allocate/free fast register MRs;
- Allocate/free fast register MR page lists;
- Fast register MR send queue work requests;
- Local DMA L_Key.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Current code uses kmalloc() and then just does a bitwise OR operation on
qp->flags in create_qp_common(), which means that qp->flags may
potentially have some unintended bits set. This patch uses kzalloc()
and avoids further explicit clearing of structure members, which also
shrinks the code:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-65 (-65)
function old new delta
create_qp_common 2024 1959 -65
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for handling the IB_QP_CREATE_MULTICAST_BLOCK_LOOPBACK
flag by using the per-multicast group loopback blocking feature of
mlx4 hardware.
Signed-off-by: Ron Livne <ronli@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 65adfa91 ("IB/mlx4: Fix RESET to RESET and RESET to ERROR
transitions") added some extra code to handle a QP state transition
from RESET to ERROR. However, the latest 1.2.1 version of the IB spec
has clarified that this transition is actually not allowed, so we can
remove this extra code again.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ConnectX returns the max message size it supports through the
QUERY_DEV_CAP firmware command. When modifying a QP to RTR, the max
message size for the QP must be specified. This value must not exceed
the value declared through QUERY_DEV_CAP. The current code ignores
the max allowed size and unconditionally sets the value to 2^31. This
patch sets all QPs to the max value allowed as returned from firmware.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The idea is that for QPs with fixed size work requests (eg selective
signaling QPs), before stamping the WQE, we read the value of the DS
field, which gives the effective size of the descriptor as used in the
previous post. Then we stamp only that area, since the rest of the
descriptor is already stamped.
When initializing the send queue buffer, make sure the DS field is
initialized to the max descriptor size so that the subsequent stamping
will be done on the entire descriptor area.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When creating a kernel QP where the consumer asked for a send queue
with lots of scatter/gater entries, set_kernel_sq_size() incorrectly
returned an error if the send queue stride is larger than the
hardware's maximum send work request descriptor size. This is not a
problem; the only issue is to make sure that the actual descriptors
used do not overflow the maximum descriptor size, so check this instead.
Clamp the returned max_send_sge value to be no bigger than what
query_device returns for the max_sge to avoid confusing hapless users,
even if the hardware is capable of handling a few more s/g entries.
This bug caused NFS/RDMA mounts to fail when the server adapter used
the mlx4 driver.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
drivers/infiniband/hw/mlx4/qp.c: In function 'mlx4_ib_post_send':
drivers/infiniband/hw/mlx4/qp.c:1460: warning: 'seglen' may be used uninitialized in this function
This is the dopey gcc-doesn't-know-that-foo(&var)-writes-to-var problem.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a new parameter, dmasync, to the ib_umem_get() prototype. Use dmasync = 1
when mapping user-allocated CQs with ib_umem_get().
Signed-off-by: Arthur Kepner <akepner@sgi.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jes Sorensen <jes@sgi.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: David Miller <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In addition to mlx4_ib, there will be ethernet and FC consumers of
mlx4_core, so move the code for managing kernel doorbells into the
core module to avoid having to duplicate this multiple times.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the QP was moved to another state (such as SQE) by the hardware,
then after this change the user won't have to set the IBV_QP_CUR_STATE
mask in order to execute modify QP in order to recover from this state.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a new IB_WR_SEND_WITH_INV send opcode that can be used to mark a
"send with invalidate" work request as defined in the iWARP verbs and
the InfiniBand base memory management extensions. Also put "imm_data"
and a new "invalidate_rkey" member in a new "ex" union in struct
ib_send_wr. The invalidate_rkey member can be used to pass in an
R_Key/STag to be invalidated. Add this new union to struct
ib_uverbs_send_wr. Add code to copy the invalidate_rkey field in
ib_uverbs_post_send().
Fix up low-level drivers to deal with the change to struct ib_send_wr,
and just remove the imm_data initialization from net/sunrpc/xprtrdma/,
since that code never does any send with immediate operations.
Also, move the existing IB_DEVICE_SEND_W_INV flag to a new bit, since
the iWARP drivers currently in the tree set the bit. The amso1100
driver at least will silently fail to honor the IB_SEND_INVALIDATE bit
if passed in as part of userspace send requests (since it does not
implement kernel bypass work request queueing). Remove the flag from
all existing drivers that set it until we know which ones are OK.
The values chosen for the new flag is not consecutive to avoid clashing
with flags defined in the XRC patches, which are not merged yet but
which are already in use and are likely to be merged soon.
This resurrects a patch sent long ago by Mikkel Hagen <mhagen@iol.unh.edu>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rather than have build_mlx_header() return a negative value on failure
and the length of the segments it builds on success, add a pointer
parameter to return the length and return 0 on success. This matches
the calling convention used for build_lso_seg() and generates slightly
smaller code -- eg, on 64-bit x86:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-22 (-22)
function old new delta
mlx4_ib_post_send 2023 2001 -22
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a create_flags member to struct ib_qp_init_attr that will allow a
kernel verbs consumer to create a pass special flags when creating a QP.
Add a flag value for telling low-level drivers that a QP will be used
for IPoIB UD LSO. The create_flags member will also be useful for XRC
and ehca low-latency QP support.
Since no create_flags handling is implemented yet, add code to all
low-level drivers to return -EINVAL if create_flags is non-zero.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ConnectX devices support checksum generation and verification of TCP
and UDP packets for UD IPoIB messages. This patch checks if the HCA
supports this and sets the IB_DEVICE_UD_IP_CSUM capability flag if it
does. It implements support for handling the IB_SEND_IP_CSUM send
flag and setting the csum_ok field in receive work completions.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Ali Ayub <ali@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ConnectX HCA supports shrinking WQEs, so that a single work request
can be made of multiple units of wqe_shift. This way, WRs can differ
in size, and do not have to be a power of 2 in size, saving memory and
speeding up send WR posting. Unfortunately, if we do this then the
wqe_index field in CQEs can't be used to look up the WR ID anymore, so
our implementation does this only if selective signaling is off.
Further, on 32-bit platforms, we can't use vmap() to make the QP
buffer virtually contigious. Thus we have to use constant-sized WRs to
make sure a WR is always fully within a single page-sized chunk.
Finally, we use WRs with the NOP opcode to avoid wrapping around the
queue buffer in the middle of posting a WR, and we set the
NoErrorCompletion bit to avoid getting completions with error for NOP
WRs. However, NEC is only supported starting with firmware 2.2.232,
so we use constant-sized WRs for older firmware. And, since MLX QPs
only support SEND, we use constant-sized WRs in this case.
When stamping during NOP posting, do stamping following setting of the
NOP WQE valid bit.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We use struct mlx4_buf for kernel QP, CQ and SRQ buffers, and the code
to look up an entry is duplicated in get_cqe_from_buf() and the QP and
SRQ versions of get_wqe(). Factor this out into mlx4_buf_offset().
This will also make it easier to switch over to using vmap() for buffers.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Or Gerlitz