The two API function can cover most, if not all current APIs used to
request a channel. With minimal effort dmaengine drivers, platforms and
dmaengine user drivers can be converted to use the two function.
struct dma_chan *dma_request_chan_by_mask(const dma_cap_mask_t *mask);
To request any channel matching with the requested capabilities, can be
used to request channel for memcpy, memset, xor, etc where no hardware
synchronization is needed.
struct dma_chan *dma_request_chan(struct device *dev, const char *name);
To request a slave channel. The dma_request_chan() will try to find the
channel via DT, ACPI or in case if the kernel booted in non DT/ACPI mode
it will use a filter lookup table and retrieves the needed information from
the dma_slave_map provided by the DMA drivers.
This legacy mode needs changes in platform code, in dmaengine drivers and
finally the dmaengine user drivers can be converted:
For each dmaengine driver an array of DMA device, slave and the parameter
for the filter function needs to be added:
static const struct dma_slave_map da830_edma_map[] = {
{ "davinci-mcasp.0", "rx", EDMA_FILTER_PARAM(0, 0) },
{ "davinci-mcasp.0", "tx", EDMA_FILTER_PARAM(0, 1) },
{ "davinci-mcasp.1", "rx", EDMA_FILTER_PARAM(0, 2) },
{ "davinci-mcasp.1", "tx", EDMA_FILTER_PARAM(0, 3) },
{ "davinci-mcasp.2", "rx", EDMA_FILTER_PARAM(0, 4) },
{ "davinci-mcasp.2", "tx", EDMA_FILTER_PARAM(0, 5) },
{ "spi_davinci.0", "rx", EDMA_FILTER_PARAM(0, 14) },
{ "spi_davinci.0", "tx", EDMA_FILTER_PARAM(0, 15) },
{ "da830-mmc.0", "rx", EDMA_FILTER_PARAM(0, 16) },
{ "da830-mmc.0", "tx", EDMA_FILTER_PARAM(0, 17) },
{ "spi_davinci.1", "rx", EDMA_FILTER_PARAM(0, 18) },
{ "spi_davinci.1", "tx", EDMA_FILTER_PARAM(0, 19) },
};
This information is going to be needed by the dmaengine driver, so
modification to the platform_data is needed, and the driver map should be
added to the pdata of the DMA driver:
da8xx_edma0_pdata.slave_map = da830_edma_map;
da8xx_edma0_pdata.slavecnt = ARRAY_SIZE(da830_edma_map);
The DMA driver then needs to configure the needed device -> filter_fn
mapping before it registers with dma_async_device_register() :
ecc->dma_slave.filter_map.map = info->slave_map;
ecc->dma_slave.filter_map.mapcnt = info->slavecnt;
ecc->dma_slave.filter_map.fn = edma_filter_fn;
When neither DT or ACPI lookup is available the dma_request_chan() will
try to match the requester's device name with the filter_map's list of
device names, when a match found it will use the information from the
dma_slave_map to get the channel with the dma_get_channel() internal
function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The DMAengine API has a long standing race condition that is inherent to
the API itself. Calling dmaengine_terminate_all() is supposed to stop and
abort any pending or active transfers that have previously been submitted.
Unfortunately it is possible that this operation races against a currently
running (or with some drivers also scheduled) completion callback.
Since the API allows dmaengine_terminate_all() to be called from atomic
context as well as from within a completion callback it is not possible to
synchronize to the execution of the completion callback from within
dmaengine_terminate_all() itself.
This means that a user of the DMAengine API does not know when it is safe
to free resources used in the completion callback, which can result in a
use-after-free race condition.
This patch addresses the issue by introducing an explicit synchronization
primitive to the DMAengine API called dmaengine_synchronize().
The existing dmaengine_terminate_all() is deprecated in favor of
dmaengine_terminate_sync() and dmaengine_terminate_async(). The former
aborts all pending and active transfers and synchronizes to the current
context, meaning it will wait until all running completion callbacks have
finished. This means it is only possible to call this function from
non-atomic context. The later function does not synchronize, but can still
be used in atomic context or from within a complete callback. It has to be
followed up by dmaengine_synchronize() before a client can free the
resources used in a completion callback.
In addition to this the semantics of the device_terminate_all() callback
are slightly relaxed by this patch. It is now OK for a driver to only
schedule the termination of the active transfer, but does not necessarily
have to wait until the DMA controller has completely stopped. The driver
must ensure though that the controller has stopped and no longer accesses
any memory when the device_synchronize() callback returns.
This was in part done since most drivers do not pay attention to this
anyway at the moment and to emphasize that this needs to be done when the
device_synchronize() callback is implemented. But it also helps with
implementing support for devices where stopping the controller can require
operations that may sleep.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Move the current client-side documentation to a subfolder to prepare the
introduction of a provider-side API documentation.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Vinod Koul