Reworked auto white balance feature (awb) to cope with all four channels.
Implemented stretching and grey world algorithms.
Using the histogram, the ISC will auto adjust the white balance during
frame captures.
Because each histogram needs a frame, it will take 4 frames for one adjustment.
When the gains were updated by previous code, the registers for the gains
were updated only on new streaming start. Now, after each full histogram the
registers are updated with new gains.
Also, on previous code, if the streaming stopped but not all 3 histograms
finished, a new histogram was started either way. This used to lead to an
error "timeout to update profile" when streaming was stopped.
According to the hardware, histogram can only work together with the capture,
not independently.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This will limit the incoming pixels per frame from the sensor.
Currently, the ISC will stop sampling the frame only when the vsync/hsync
are detected.
If we misconfigure the resolution in the sensor w.r.t. resolution in the ISC,
the buffer used for DMA in the ISC will be smaller than the number of pixels
that the ISC DMA engine will copy.
In this case it happens that the DMA will overwrite parts of the memory which
should not be written, leading to memory corruption.
To avoid this situation, use the PFE CFG1 and PFE CFG2 registers, which crop
the incoming frame to the resolution that we configure.
This way the DMA engine will never write more data than we expect it to.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ISC driver currently supports ITU-R 601 encoding which
utilizes the external hsync and vsync signals. ITU-R 656
format removes the need for these pins by embedding the
sync pulses within the data packet.
To support this feature, enable necessary register bits
when this feature is enabled via device tree.
Signed-off-by: Ken Sloat <ksloat@aampglobal.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----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=d9nT
-----END PGP SIGNATURE-----
Merge tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Documentation for digital TV (both kAPI and uAPI) are now in sync
with the implementation (except for legacy/deprecated ioctls). This
is a major step, as there were always a gap there
- New sensor driver: imx274
- New cec driver: cec-gpio
- New platform driver for rockship rga and tegra CEC
- New RC driver: tango-ir
- Several cleanups at atomisp driver
- Core improvements for RC, CEC, V4L2 async probing support and DVB
- Lots of drivers cleanup, fixes and improvements.
* tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (332 commits)
dvb_frontend: don't use-after-free the frontend struct
media: dib0700: fix invalid dvb_detach argument
media: v4l2-ctrls: Don't validate BITMASK twice
media: s5p-mfc: fix lockdep warning
media: dvb-core: always call invoke_release() in fe_free()
media: usb: dvb-usb-v2: dvb_usb_core: remove redundant code in dvb_usb_fe_sleep
media: au0828: make const array addr_list static
media: cx88: make const arrays default_addr_list and pvr2000_addr_list static
media: drxd: make const array fastIncrDecLUT static
media: usb: fix spelling mistake: "synchronuously" -> "synchronously"
media: ddbridge: fix build warnings
media: av7110: avoid 2038 overflow in debug print
media: Don't do DMA on stack for firmware upload in the AS102 driver
media: v4l: async: fix unregister for implicitly registered sub-device notifiers
media: v4l: async: fix return of unitialized variable ret
media: imx274: fix missing return assignment from call to imx274_mode_regs
media: camss-vfe: always initialize reg at vfe_set_xbar_cfg()
media: atomisp: make function calls cleaner
media: atomisp: get rid of storage_class.h
media: atomisp: get rid of wrong stddef.h include
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A software write operation to the ISC_CLKEN or ISC_CLKDIS register
requires double clock domain synchronization and is not permitted
when the ISC_SR.SIP is asserted. So add the .prepare and .unprepare
ops to make sure the ISC_CLKSR.SIP is unasserted before the write
operation to the ISC_CLKEN or ISC_CLKDIS register.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Image Sensor Controller has an internal image processor.
It can convert raw format to the other formats, like
RGB565, YUV420P. A module parameter 'sensor_preferred'
is used to enable or disable the pipeline function.
Some v4l2 controls are added to tuning the image when
the pipeline function is enabled.
Signed-off-by: Songjun Wu <songjun.wu@microchip.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add driver for the Image Sensor Controller. It manages
incoming data from a parallel based CMOS/CCD sensor.
It has an internal image processor, also integrates a
triple channel direct memory access controller master
interface.
Signed-off-by: Songjun Wu <songjun.wu@microchip.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Eugen Hristev