Restrict our published beamformee STS capability according
to the AP value.
Some AP show bad behaviour in interoperability testing
when our capabilities are better.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Initialize the buffer to all zeroes, otherwise the stack
data might be interpreted as the TID, which is likely to
fail completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case the given ROC duration is 0, update it to a minimal value before
setting the ieee80211_roc_work parameters, so it also would be valid
for cases where scan is in progress or there are other ROCs queued.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we copy the mesh_id_len into our own data structures,
use it consistently and don't sometimes use cfg80211's copy.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh_id is an array so can't ever be NULL, it looks
like mesh_id_len check was intended instead. However,
since the previous patch, cfg80211 does the check, so
just remove it here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh precedence value in ieee80211_channel_switch
should be incremented or set to 1 only if this is the
initiator of mesh channel switch. For non-initiator,
the precedence value has updated using the Mesh
Channel Switch Parameters element. Fix this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When IEEE80211_HW_SIGNAL_UNSPEC is set, mac80211 will perform a
division by max_signal in ieee80211_bss_info_update. If max_signal
is not properly set by the driver (for example it is zero) this
leads to a divide error and crash.
Thanks to Larry Finger, who pointed me to this.
This patch adds in ieee80211_register_hw one more check to detect
this condition and eventually returns -EINVAL, as already done for
other checks already performed there.
Signed-off-by: andrea merello <andrea.merello@gmail.com>
[move to an already existing SIGNAL_UNSPEC check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 7ec7c4a9a6 ("mac80211: port CCMP to cryptoapi's CCM driver")
resulted in the 'encrypted' param of ccmp_special_blocks() to be no
longer used so it can be dropped from the prototype.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A beacon should never have a Channel Switch Announcement information
element with a count of 0, because a count of 1 means switch just
before the next beacon. So, if a count of 0 was valid in a beacon, it
would have been transmitted in the next channel already, which is
useless. A CSA count equal to zero is only meaningful in action
frames or probe_responses.
Fix the ieee80211_csa_is_complete() and ieee80211_update_csa()
functions accordingly.
With a CSA count of 0, we won't transmit any CSA beacons, because the
switch will happen before the next TBTT. To avoid extra work and
potential confusion in the drivers, complete the CSA immediately,
instead of waiting for the driver to call ieee80211_csa_finish().
To keep things simpler, we also switch immediately when the CSA count
is 1, while in theory we should delay the switch until just before the
next TBTT.
Additionally, move the ieee80211_csa_finish() function to cfg.c,
where it makes more sense.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Acked-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The return value of ieee80211_mesh_csa_beacon is not aligned with the
return value of ieee80211_assign_beacon() and
ieee80211_ibss_csa_beacon(). For consistency and to be able to use
both functions with similar code, change ieee80211_mesh_csa_beacon()
not to send the bss changed notification itself, but return what has
changed so the caller can send the notification instead.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Acked-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor ieee80211_mesh_process_chanswitch() to use
ieee80211_channel_switch() and avoid code duplication.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Acked-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, the tx queue were selected implicitly in ndo_dfwd_start_xmit(). The
will cause several issues:
- NETIF_F_LLTX were removed for macvlan, so txq lock were done for macvlan
instead of lower device which misses the necessary txq synchronization for
lower device such as txq stopping or frozen required by dev watchdog or
control path.
- dev_hard_start_xmit() was called with NULL txq which bypasses the net device
watchdog.
- dev_hard_start_xmit() does not check txq everywhere which will lead a crash
when tso is disabled for lower device.
Fix this by explicitly introducing a new param for .ndo_select_queue() for just
selecting queues in the case of l2 forwarding offload. netdev_pick_tx() was also
extended to accept this parameter and dev_queue_xmit_accel() was used to do l2
forwarding transmission.
With this fixes, NETIF_F_LLTX could be preserved for macvlan and there's no need
to check txq against NULL in dev_hard_start_xmit(). Also there's no need to keep
a dedicated ndo_dfwd_start_xmit() and we can just reuse the code of
dev_queue_xmit() to do the transmission.
In the future, it was also required for macvtap l2 forwarding support since it
provides a necessary synchronization method.
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a uAPSD service period ends with an MMPDU, we currently just
send that MMPDU, but it obviously won't get the EOSP bit set as
it doesn't have a QoS header. This contradicts the standard, so
add a QoS-nulldata frame after the MMPDU to properly terminate
the service period with a frame that has EOSP set.
Also fix a bug wrt. the TID for the MMPDU, it shouldn't be set
to 0 unconditionally but use the actual TID that was assigned.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The temporary TX info flags need to be cleared if the frame will
be processed through the TX handlers again, otherwise it can get
messed up. This fixes a bug that happened when an aggregation
session was stopped while the station was sleeping - some frames
might get transmitted marked as aggregation erroneously without
this fix.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a response for PS-Poll or a uAPSD trigger frame is sent, the
more-data bit should be set according to 802.11-2012 11.2.1.5 h),
meaning that it should indicate more data on the relevant ACs
(delivery-enabled or nondelivery-enabled for uAPSD or PS-Poll.)
In, for example, the following scenario:
* 1 frame on VO queue (either in driver or in mac80211)
* at least 1 frame on VI queue (in the driver)
* both VO/VI are delivery-enabled
* uAPSD trigger frame received
The more-data flag to the driver would not be set, even though
it should be.
While fixing this, I noticed that we should really release frames
from multiple ACs where there's data buffered in the driver for
the corresponding TIDs.
To address all this, restructure the code a bit to consider all
ACs if we only release driver frames or only buffered frames.
This also addresses the more-data bug described above as now the
TIDs will all be marked as released, so the driver will have to
check the number of frames.
While at it, clarify some code and comments and remove the found
variable, replacing it with the appropriate sw/hw release check.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using ffs() for the PS-Poll release TID is wrong, it will cause
frames to be released in order 0 1 2 3 4 5 6 7 instead of the
correct 7 6 5 4 3 0 2 1. Fix this by adding a new function that
implements "highest priority TID" properly.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In managed mode, we should not ask for OFF mode because the
power settings may still require DYNAMIC. In AP mode, this
should be allowed since the default settings is OFF and
AUTOMATIC is not allowed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using an int with 0/1 is not very common, make the function
return a bool instead with the same values (false/true).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No need to assign the return value of prepare_for_handlers
to a variable if the only usage is to test it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On starting a mesh or AP BSS, the interface dtim_count
countdown should match that of the driver TSF.
Signed-off-by: Thomas Pedersen <twpedersen@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enable the WME for peer mesh STA so that the driver,
such as wcn36xx, will pick this up and enabling it in HW.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the internal scan request allocation below the last
sanity check in ieee80211_register_hw() to avoid leaking
memory if the sanity check actually triggers.
Reported-by: ZHAO Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the station's TX latency data structures need to be
allocated, handle failures properly and also free all the
structures if there are any other problems.
Move the allocation code up so that allocation failures
don't trigger rate control algorithm calls.
Reported-by: ZHAO Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clean up the file macros a bit and use that to remove the
unnecessary format function for the tkip MIC test file
that really is write-only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is useful for debugging issues with drivers using this
function (erroneously), so add tracing for the API call.
Change-Id: Ice9d7eabb8fecbac188f0a741920d3488de700ec
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the RTNL can't always be held, use wdev/sdata locking for
the qos-map dereference in mac80211. This requires cfg80211 to
consistently lock it, which it was missing in one place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: David Miller <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows QoS mapping from external networks to be implemented as
defined in IEEE Std 802.11-2012, 10.24.9. APs can use this to advertise
DSCP ranges and exceptions for mapping frames to a specific UP over
Wi-Fi.
The payload of the QoS Map Set element (IEEE Std 802.11-2012, 8.4.2.97)
is sent to the driver through the new NL80211_ATTR_QOS_MAP attribute to
configure the local behavior either on the AP (based on local
configuration) or on a station (based on information received from the
AP).
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The scan code creates an iflist_mtx -> mtx locking dependency,
and a few other places, notably radar detection, were creating
the opposite dependency, causing lockdep to complain. As scan
and radar detection are mutually exclusive, the deadlock can't
really happen in practice, but it's still bad form.
A similar issue exists in the monitor mode code, but this is
only used by channel-context drivers right now and those have
to have hardware scan, so that also can't happen.
Still, fix these issues by making some of the channel context
code require the mtx to be held rather than acquiring it, thus
allowing the monitor/radar callers to keep the iflist_mtx->mtx
lock ordering.
While at it, also fix access to the local->scanning variable
in the radar code, and document that radar_detect_enabled is
now properly protected by the mtx.
All this would now introduce an ABBA deadlock between the DFS
work cancelling and local->mtx, so change the locking there a
bit to not need to use cancel_delayed_work_sync() but be able
to just use cancel_delayed_work(). The work is also safely
stopped/removed when the interface is stopped, so no extra
changes are needed.
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The radar detection code changed a few times, and due to
the changes some iflist_mtx locking stayed in that isn't
actually necessary - remove it.
One version of the code needed it because an AP interface's
VLAN list was changed to use this, but then we moved the
list handling outside of the chanctx handling and thus the
locking was no longer needed.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Its address is used as an unsigned long *, so make sure
that the tim u8 array is properly aligned.
Signed-off-by: Joe Perches <joe@perches.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function is only used in one file, so move it up a
bit to avoid forward declarations and make it static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix a number of different checkpatch errors.
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The check needs to apply to both multicast and unicast packets,
otherwise probe requests on AP mode scans are sent through the multicast
buffer queue, which adds long delays (often longer than the scanning
interval).
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow to read management keys stored in a station's gtk key
array with a get_key function.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Verify that a pairwise key index value on ieee80211_get_key call
doesn't exceed the boundaries of the pairwise key array.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The return value of ieee80211_ibss_csa_beacon is not aligned with the
return value of ieee80211_assign_beacon(). For consistency and to be
able to use both functions with similar code, change
ieee80211_ibss_csa_beacon() not to send the bss changed notification
itself, but return what has changed so the caller can send the
notification instead.
Tested by: Simon Wunderlich <sw@simonwunderlich.de>
Acked by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor ieee80211_ibss_process_chanswitch() to use
ieee80211_channel_switch() and avoid code duplication.
Tested by: Simon Wunderlich <sw@simonwunderlich.de>
Acked by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This regression was introduced in "mac80211: cache mesh
beacon".
mesh_sync_offset_adjust_tbtt() was assuming that the
beacon would be rebuilt in every single pre-tbtt
interrupt, but now the beacon update happens on the
workqueue, and it must be ready for immediate delivery to
the driver.
Save a pointer to the meshconf IE in the beacon_data (this
works because both the IE pointer and beacon buffer are
protected by the same rcu_{dereference,assign_pointer}())
for quick updates during pre-tbtt. This is faster and a
little prettier than iterating over the elements to find
the meshconf IE every time.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Keep the sched scan req when starting sched scan, and reschedule
it in case of HW restart during sched scan.
The upper layer don't have to know about the restart.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function is not used anywhere else than in cfg.c, so there's no
need to export it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We call ieee80211_ibss_disconnect(), which requires sdata to be
locked, so lock the sdata during ieee80211_csa_connection_drop_work().
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Can be used to add extra IEs (such as P2P NoA) without having to
reallocate the buffer.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the AP interface is stopped, free all AP and VLAN keys at
once to only require synchronize_net() once. Since that does
synchronize_net(), also move two such calls into the function
(using the new force_synchronize parameter) to avoid doing it
twice.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Teach sta_info_flush() to optionally also remove stations
from all VLANs associated with an AP interface to optimise
the station removal (in particular, synchronize_net().)
To not have to add the vlans argument throughout, do some
refactoring.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no reason to have one synchronize_net() for each
removed station, refactor the code slightly to have just
a single synchronize_net() for all stations.
Note that this is currently useless as hostapd removes
stations one by one and this coalescing never happens.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no reason to do this inside the sta key removal
since the keys can only be reached through the sta (and
not by the driver at all) so once the sta can no longer
be reached, the keys are safe.
This will allow further optimisation opportunities with
multiple stations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we can assume that stations are never referenced by the
driver after sta_state returns (and this is true since the
previous iwlmvm patch and for all other drivers) then we
don't need to delay station destruction, and don't need to
play tricks with rcu_barrier() etc.
This should speed up some scenarios like hostapd shutdown.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The pointer should be cleared before synchronize_rcu() so that the
consequently dead station won't be found by any lookups in the TX
or RX paths.
Also check that the station is actually the one being removed, the
check is not needed because each 4-addr VLAN can only have a single
station and non-4-addr VLANs always have a NULL pointer there, but
the code is clearer this way (and we avoid the memory write.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, mac80211 allows drivers to keep RCU-protected station
references that are cleared when the station is removed from the
driver and consequently needs to synchronize twice, once before
removing the station from the driver (so it can guarantee that
the station is no longer used in TX towards the driver) and once
after the station is removed from the driver.
Add a new pre-RCU-synchronisation station removal operation to
the API to allow drivers to clear/invalidate their RCU-protected
station pointers before the RCU synchronisation.
This will allow removing the second synchronisation by changing
the driver API so that the driver may no longer assume a valid
RCU-protected pointer after sta_remove/sta_state returns.
The alternative to this would be to synchronize_rcu() in all the
drivers that currently rely on this behaviour (only iwlmvm) but
that would defeat the purpose.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fixes a regression introduced by my patch "mac80211: don't cancel
csa finalize work within stop_ap", which added sdata locks to
ieee80211_csa_finalize_work() without removing the locking for
ieee80211_ibss_finish_csa(), which is called by the former, resulting
in a deadlock due to nested locking.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On scan completion we try start any pending roc.
However, if scan was just pending (and not actually started)
there is no point in trying to start the roc, as it might
have started already.
This solves the following warning:
WARNING: CPU: 0 PID: 3552 at net/mac80211/offchannel.c:269 ieee80211_start_next_roc+0x164/0x204 [mac80211]()
[<c001cd38>] (unwind_backtrace+0x0/0xf0)
[<c00181d0>] (show_stack+0x10/0x14)
[<c05c0d8c>] (dump_stack+0x78/0x94)
[<c0047c08>] (warn_slowpath_common+0x68/0x8c)
[<c0047c48>] (warn_slowpath_null+0x1c/0x24)
[<bf4d6660>] (ieee80211_start_next_roc+0x164/0x204 [mac80211])
[<bf4d5a74>] (ieee80211_scan_cancel+0xe8/0x190 [mac80211])
[<bf4df970>] (ieee80211_do_stop+0x63c/0x79c [mac80211])
[<bf4dfae0>] (ieee80211_stop+0x10/0x18 [mac80211])
[<c0504d84>] (__dev_close_many+0x84/0xcc)
[<c0504df4>] (__dev_close+0x28/0x3c)
[<c0509708>] (__dev_change_flags+0x78/0x144)
[<c0509854>] (dev_change_flags+0x10/0x48)
[<c055fe3c>] (devinet_ioctl+0x614/0x6d0)
[<c04f22a0>] (sock_ioctl+0x5c/0x2a4)
[<c0124eb4>] (do_vfs_ioctl+0x7c/0x5d8)
[<c012547c>] (SyS_ioctl+0x6c/0x7c)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, determining the completed scan type was
done by testing the SCAN_HW_SCANNING flag.
However, this doesn't take care for the case in which
the hw scan was requested, but hasn't started yet (e.g.
due to active remain_on_channel).
Replace this test by checking whether ops->hw_scan is
defined.
This solves the following warning:
WARNING: CPU: 0 PID: 3552 at net/mac80211/offchannel.c:156 __ieee80211_scan_completed+0x1b4/0x2dc [mac80211]()
[<c001cd38>] (unwind_backtrace+0x0/0xf0)
[<c00181d0>] (show_stack+0x10/0x14)
[<c05c0d8c>] (dump_stack+0x78/0x94)
[<c0047c08>] (warn_slowpath_common+0x68/0x8c)
[<c0047c48>] (warn_slowpath_null+0x1c/0x24)
[<bf4d4504>] (__ieee80211_scan_completed+0x1b4/0x2dc [mac80211])
[<bf4d5a74>] (ieee80211_scan_cancel+0xe8/0x190 [mac80211])
[<bf4df970>] (ieee80211_do_stop+0x63c/0x79c [mac80211])
[<bf4dfae0>] (ieee80211_stop+0x10/0x18 [mac80211])
[<c0504d84>] (__dev_close_many+0x84/0xcc)
[<c0504df4>] (__dev_close+0x28/0x3c)
[<c0509708>] (__dev_change_flags+0x78/0x144)
[<c0509854>] (dev_change_flags+0x10/0x48)
[<c055fe3c>] (devinet_ioctl+0x614/0x6d0)
[<c04f22a0>] (sock_ioctl+0x5c/0x2a4)
[<c0124eb4>] (do_vfs_ioctl+0x7c/0x5d8)
[<c012547c>] (SyS_ioctl+0x6c/0x7c)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rename NL80211_TXRATE_MCS to NL80211_TXRATE_HT and also
rename mcs to ht_mcs in struct cfg80211_bitrate_mask.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the unnecessary duplicate test of "if (skb) {"
when !CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS.
Remove now unnecessary __maybe_unused, neaten comment
Remove unnecessary parenthesis around align cast.
Substitute reference to deprecated compare_ether_addr
with ether_addr_equal (in the comment.)
Signed-off-by: Joe Perches <joe@perches.com>
[edit commit log slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for vendor-specific commands to nl80211. This is
intended to be used for really vendor-specific functionality
that can't be implemented in a generic fashion for any reason.
It's *NOT* intended to be used for any normal/generic feature
or any optimisations that could be implemented across drivers.
Currently, only vendor commands (with replies) are supported,
no dump operations or vendor-specific notifications.
Also add a function wdev_to_ieee80211_vif() to mac80211 which
is needed for mac80211-based drivers wanting to implement any
vendor commands.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 488b366a45.
The code isn't used by anyone, and the Intel driver isn't planning
to use it either right now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers with hardware rate control were given
sta->rx_nss set to 0. This was because rx_nss
calculation procedure was protected by hw/sw rate
control check.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When external CSA IEs are received (beacons or action messages), a
channel switch is triggered as well. This should only be allowed on
devices which actually support channel switches, otherwise disconnect.
(For the corresponding userspace invocation, the wiphy flag is checked
in nl80211).
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current channel switch code has a potential deadlock:
1) * cfg80211_stop_ap acquires wdev-lock
* ieee80211_stop_ap calls cancel_work_sync for the csa_finalize_work,
which acquires the associated worker-lock
2) * ieee80211_csa_finalize_work holds the worker-lock when run
* it calls cfg80211_ch_switch_notify which will claim the wdev-lock,
and also needs to claim the sdata-lock (which is the same as the
wdev-lock) to modify the beacons.
It is sufficient to just set the channel switch active to false. If the
worker is running later, it will find the channel switch to not be
active anymore and returns immediately without changing anything.
Canceling the worker is done anyway when the interface goes down
(ieee80211_do_stop).
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The channel switch notification should be sent under the
wdev/sdata-lock, preferably in the same moment as the channel change
happens, to avoid races by other callers (e.g. start/stop_ap).
This also adds the previously missing sdata_lock protection in
csa_finalize_work.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The csa finalize worker needs to change the beacon information (for
different modes). These are normally protected under rtnl lock, but the
csa finalize worker is called by drivers and should not acquire the RTNL
lock. Therefore change access protection for beacons to sdata/wdev lock.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[fix sdata_dereference]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The local TSF timer is used to compute the timing offset between
mesh peers on beacon reception. However, asking the device for
the TSF is not very accurate, so we prefer to use rx->mactime
if available. In the latter case, calling drv_get_tsf() just
adds more delay into the RX path, so skip it if we can.
Signed-off-by: Bob Copeland <bob@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change cfg80211 and mac80211 to use cfg80211_mgmt_tx_params
struct to aggregate parameters for mgmt_tx functions.
This makes the functions' signatures less clumsy and allows
less painful parameters extension.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
[fix all other drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a bug in tracking HT opmode changes in mac80211, it
fails to update the driver when the channel parameters don't
change.
Move the code to do the HT opmode checking independently of
the channel/bandwidth tracking.
Signed-off-by: Avri Altman <avri.altman@intel.com>
[edit commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All interface types now properly clean up their stations
using some form of sta_info_flush() themselves, so there's
no need to try it again at teardown. Remove the call to
get rid of the extra delay from the synchronize_net() and
rcu_barrier() calls.
Reported-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Measure TX latency and jitter statistics per station per TID.
These Measurements are disabled by default and can be enabled
via debugfs.
Features included for each station's TID:
1. Keep count of the maximum and average latency of Tx frames.
2. Keep track of many frames arrived in a specific time range
(need to enable through debugfs and configure the bins ranges)
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ATM minstrel_ht does not check whether a sampling rate is supported.
Unsupported rates attempts can trigger when there are holes in bitfields
of supported MCSes belonging to the same group (e.g many devices are
MCS32 capable without MCS33->39 capable, also we systematically have a
hole for CCK rates).
Drop any attempts to sample unsupported rates, as suggested by Felix.
This is not a problem in minstrel which fills a per STA sample table
with only supported rates (though only at init).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ATM, only the first array value returned by get_random_bytes is used.
This change moves the call to get_random_bytes from the nested loop it
is in to its parent.
While at it, replace get_random_bytes with prandom_bytes since PRNs are
way enough for the selection process.
After this, minstrel_ht reclaims 80 PR-bytes instead of 640 R-bytes.
minstrels use sample tables to probe different rates in a randomized
manner.
minstrel_ht inits one single sample table upon registration (during
subsys_initcalls) and minstrel uses one per STA addition in minstrel.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Consecutive MCSes in [8*(NSS-1)->8*NSS[ have the same number NSS of
streams (except for MCS32 which is mishandled ATM).
ATM minstrel_ht uses MCS_GROUP_RATES in place of this 8 modulus.
This change replaces such occurences and by doing so allows for different
values of MCS_GROUP_RATES (e.g to cope with VHT MCS8,9).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new field to ieee80211_chanctx_conf to indicate
the min required channel configuration.
Tuning to a narrower channel might help reducing
the noise level and saving some power.
The min required channel definition is the max of
all min required channel definitions of the interfaces
bound to this channel context.
In AP mode, use 20MHz when there are no connected station.
When a new station is added/removed, calculate the new max
bandwidth supported by any of the stations (e.g. 80MHz when
80MHz and 40MHz stations are connected).
In other cases, simply use bss_conf.chandef as the
min required chandef.
Notify drivers about changes to this field by calling
drv_change_chanctx with a new CHANGE_MIN_WIDTH notification.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce shift and mask defines for beamformee STS cap and number
of sounding dimensions cap as these can take any 3 bit value.
While at it also cleanup an unrequired parenthesis.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no reason why we should have only one channel switch
announcement at a time for a single phy. When support for channel
switch with multiple contexts and multiple vifs per context is
implemented, we will need the chandef data for each vif. Move the
csa_chandef structure to sdata to prepare for this.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
[Fixed compilation with mesh]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use put_unaligned_le16 and put_unaligned_le32 for
mesh_path_error_tx and mesh_path_sel_frame_tx.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use put_unaligned_le16 in mesh_plink_frame_tx.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
use put_unaligned_le16 for precedence value in mesh
channel switch support
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds generic cipher scheme support to mac80211, such schemes
are fully under control by the driver. On hw registration drivers
may specify additional HW ciphers with a scheme how these ciphers
have to be handled by mac80211 TX/RR. A cipher scheme specifies a
cipher suite value, a size of the security header to be added to
or stripped from frames and how the PN is to be verified on RX.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To report channel width correctly we have
to send correct channel parameters from
mac80211 when calling cfg80211_cac_event().
This is required in case of using channel width
higher than 20MHz and we have to set correct
dfs channel state after CAC (NL80211_DFS_AVAILABLE).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no code calling ieee80211_key_replace() with both
arguments NULL and it wouldn't make sense, but in the
interest of maintainability add a warning for it. As a
side effect, this also shuts up a smatch warning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Coverity points out that checking assoc_data->ie is
completely useless since it's an array in the struct
and can't be NULL - remove the useless checks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
802.11-2012 13.3.1 implicitly limits the mesh local link
ID range to that of AID, since for mesh PS the local link
ID must be indicated in the TIM IE, which only holds
IEEE80211_MAX_AID bits.
Also the code was allowing a local link ID of 0, but this
is not correct since that TIM bit is used for indicating
buffered mcast frames.
Generate a random, unique, link ID from 1 - 2007, and drop
a modulo conversion for the local link ID, but keep it for
the peer link ID in case he chose something > MAX_AID.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[fix some indentation, squash llid assignment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we store the peer link ID right after initializing a
new neighbor, there is no need to do it later in the
peering FSM.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Eyal Shapira