In the event that register_netdev() failed, the rrpriv->evt_ring
allocation would have not been freed.
Signed-off-by: David Oostdyk <daveo@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f4a46d1f46 introduced a bug where
the ifconfig stats would remain 0 for phylib devices. This is due to
tp->link_up flag never becoming true causing tg3_periodic_fetch_stats()
to return.
The link_up flag was being updated in tg3_test_and_report_link_chg()
after setting up the phy. This function however, is not called for
phylib devices since the driver does not do the phy setup.
This patch moves the link_up flag update into the common
tg3_link_report() function that gets called for phylib devices as well
for non phylib devices when the link state changes.
To avoid updating link_up twice, we replace tg3_carrier_...() calls that
are followed by tg3_link_report(), with netif_carrier_...(). We can then
remove the unused tg3_carrier_on() function.
CC: <stable@vger.kernel.org>
Reported-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a problem in which iSCSI-boot installation fails when switching SFP+ boot
port and moving the SFP+ module prior to boot. The SFP+ insertion triggers an
interrupt which configures the SFP+ module wrongly before interface is loaded.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a KR2 device is connected to a KR link-partner, sometimes it requires
disabling KR2 for the link to come up. To get a KR2 link up later, in case no
base pages are seen, the KR2 is restored. The problem was that some link
partners cleared their advertised BP/NP after around two seconds, causing the
driver to disable/enable KR2 link all the time.
The fix was to wait at least 5 seconds before checking KR2 recovery.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macvlan already supports hw address filters. Set the IFF_UNICAST_FLT
so that it doesn't needlesly enter PROMISC mode when macvlans are
stacked.
Signed-of-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a team port is removed, unsync all devices addresses that may have
been synched to the port devices.
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
When autoneg has been disabled in the PHY (Marvell 88E1118 here), auto
negotiation between MAC and PHY seem non-functional anymore. The only
way I found to workaround this is to manually configure the MAC with the
settings sent to the PHY earlier.
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if we set up netconsole over bonding and release a slave,
netconsole will stop logging on the whole bonding device. Change the
behavior to stop the netconsole only when the last slave is released.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following script will produce a kernel oops:
sudo ip netns add v
sudo ip netns exec v ip ad add 127.0.0.1/8 dev lo
sudo ip netns exec v ip link set lo up
sudo ip netns exec v ip ro add 224.0.0.0/4 dev lo
sudo ip netns exec v ip li add vxlan0 type vxlan id 42 group 239.1.1.1 dev lo
sudo ip netns exec v ip link set vxlan0 up
sudo ip netns del v
where inspect by gdb:
Program received signal SIGSEGV, Segmentation fault.
[Switching to Thread 107]
0xffffffffa0289e33 in ?? ()
(gdb) bt
#0 vxlan_leave_group (dev=0xffff88001bafa000) at drivers/net/vxlan.c:533
#1 vxlan_stop (dev=0xffff88001bafa000) at drivers/net/vxlan.c:1087
#2 0xffffffff812cc498 in __dev_close_many (head=head@entry=0xffff88001f2e7dc8) at net/core/dev.c:1299
#3 0xffffffff812cd920 in dev_close_many (head=head@entry=0xffff88001f2e7dc8) at net/core/dev.c:1335
#4 0xffffffff812cef31 in rollback_registered_many (head=head@entry=0xffff88001f2e7dc8) at net/core/dev.c:4851
#5 0xffffffff812cf040 in unregister_netdevice_many (head=head@entry=0xffff88001f2e7dc8) at net/core/dev.c:5752
#6 0xffffffff812cf1ba in default_device_exit_batch (net_list=0xffff88001f2e7e18) at net/core/dev.c:6170
#7 0xffffffff812cab27 in cleanup_net (work=<optimized out>) at net/core/net_namespace.c:302
#8 0xffffffff810540ef in process_one_work (worker=0xffff88001ba9ed40, work=0xffffffff8167d020) at kernel/workqueue.c:2157
#9 0xffffffff810549d0 in worker_thread (__worker=__worker@entry=0xffff88001ba9ed40) at kernel/workqueue.c:2276
#10 0xffffffff8105870c in kthread (_create=0xffff88001f2e5d68) at kernel/kthread.c:168
#11 <signal handler called>
#12 0x0000000000000000 in ?? ()
#13 0x0000000000000000 in ?? ()
(gdb) fr 0
#0 vxlan_leave_group (dev=0xffff88001bafa000) at drivers/net/vxlan.c:533
533 struct sock *sk = vn->sock->sk;
(gdb) l
528 static int vxlan_leave_group(struct net_device *dev)
529 {
530 struct vxlan_dev *vxlan = netdev_priv(dev);
531 struct vxlan_net *vn = net_generic(dev_net(dev), vxlan_net_id);
532 int err = 0;
533 struct sock *sk = vn->sock->sk;
534 struct ip_mreqn mreq = {
535 .imr_multiaddr.s_addr = vxlan->gaddr,
536 .imr_ifindex = vxlan->link,
537 };
(gdb) p vn->sock
$4 = (struct socket *) 0x0
The kernel calls `vxlan_exit_net` when deleting the netns before shutting down
vxlan interfaces. Later the removal of all vxlan interfaces, where `vn->sock`
is already gone causes the oops. so we should manually shutdown all interfaces
before deleting `vn->sock` as the patch does.
Signed-off-by: Zang MingJie <zealot0630@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux is free to call ethtool ops as soon as a netdev exists when probe
finishes. However, we only allocate vmxnet3 tx/rx queues and initialize the
rx_buf_per_pkt field in struct vmxnet3_adapter when the interface is
opened (UP).
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 37706996 "mlx4_en: fix allocation of CPU affinity reverse-map" fixed
a bug when mlx4_dev->caps.comp_pool is larger from the device rx rings, but
introduced a regression.
When the mlx4_core is activating its "legacy mode" (e.g when running in SRIOV
mode) w.r.t to EQs/IRQs usage, comp_pool becomes zero and we're crashing on
divide by zero alloc_cpu_rmap.
Fix that by enabling RFS only when running in non-legacy mode.
Reported-by: Yan Burman <yanb@mellanox.com>
Cc: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we cleanup all MAC related resources (entries in the port MAC
table and steering rules) when stopping a port or when the driver is unloaded.
The leak was introduced by commit 07cb4b0a "net/mlx4_en: Manage hash of MAC
addresses per port".
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary use of workqueue for the device MAC address setting
flow, and fix a race when setting MAC address which was introduced by
commit c07cb4b0a "net/mlx4_en: Manage hash of MAC addresses per port"
The race happened when mlx4_en_replace_mac was being executed in parallel
with a successive call to ndo_set_mac_address, e.g witn an A/B/A MAC
setting configuration test, the third set fails.
With this change we also properly report an error if set MAC fails.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The set_param_l function assumes casting a u64 pointer to a u32 pointer
allows to access the lower 32bits, but it results in writing the upper
32 bits on big endian systems.
The fixed function reads the upper 32 bits of the 64 argument, and or's
them with the 32 bits of the 32-bit value passed to the function.
Since this is now a "read-modify-write" operation, we got many
"unintialized variable" warnings which needed to be fixed as well.
Reported-by: Alexander Schmidt <alexschm@de.ibm.com>.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older kernels detect DMFS (device-managed flow steering) from the HCA
device capability directly, regardless of whether the capability was
enabled in INIT_HCA, this is fixed by commit 7b8157bed "mlx4_core: Adjustments
to Flow Steering activation logic for SR-IOV"
To protect against guests running kernels without this fix, the host driver
should turn off the DMFS capability bit in mlx4_QUERY_DEV_CAP_wrapper.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guests kernels may not correctly detect if DMFS (device-enabled flow steering) is
activated by the host. If DMFS is activated, the master should return error to guests
which try to use the B0-steering flow calls (mlx4_QP_ATTACH).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes some annoying messages like 'Error reading PHY register' and
'Hardware Erorr' and saves several seconds on reboot.
Cc: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Borislav Petkov <bp@suse.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes redundant actions from driver and fixes its interaction
with actions in pci-bus runtime power management code.
It removes pci_save_state() from __e1000_shutdown() for normal adapters,
PCI bus callbacks pci_pm_*() will do all this for us. Now __e1000_shutdown()
switches to D3-state only quad-port adapters, because they needs quirk for
clearing false-positive error from downsteam pci-e port.
pci_save_state() now called after clearing bus-master bit, thus __e1000_resume()
and e1000_io_slot_reset() must set it back after restoring configuration space.
This patch set get_link_status before calling pm_runtime_put() in e1000_open()
to allow e1000_idle() get real link status and schedule first runtime suspend.
This patch also enables wakeup for device if management mode is enabled
(like for WoL) as result pci_prepare_to_sleep() would setup wakeup without
special actions like custom 'enable_wakeup' sign.
Cc: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Borislav Petkov <bp@suse.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes redundant and unbalanced pci_disable_device() from
__e1000_shutdown(). pci_clear_master() is enough, device can go into
suspended state with elevated enable_cnt.
Bug was introduced in commit 23606cf5d1
("e1000e / PCI / PM: Add basic runtime PM support (rev. 4)") in v2.6.35
Cc: Bruce Allan <bruce.w.allan@intel.com>
CC: Stable <stable@kernel.org>
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Borislav Petkov <bp@suse.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John W. Linville says:
====================
This time just passing along a big batch of fixes from Johannes...
For the mac80211 bits:
"Here I have fixes from Ben Greear for stray work items when deleting
interfaces, another idle handling fix from Felix, a fix from Marco ro a
mesh PS buffering crash and I have a fix for the VHT MCS calculation in
association request frames and more nl80211 feature advertising removal
as well as a workaround to increase the dump size if the SKB overhead is
too large. For 3.10 I already have a complete fix queued, but that also
requires (simple) userspace changes."
And for the iwlwifi bits:
"The patches from Dor fix a bunch of calibration issues in the new MVM
driver, and Emmanuel has a number of fixes there as well. Also, we
decided to disable 8k A-MSDU by default, so that's in there. My own
patches are addressing an issue we found with the new devices but that
seems to also exist on older ones, the DMA writeback the devices do can
be delayed and cause issues. The fix is unfortunately relatively large
and depends on two other changes (to not be hugely conflicting), but I
think it's still worth it at this point."
As Johannes says, it is a bit large. But I hope it is still early
enough in the cycle to make that worthwhile.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The SLIPORT_SEMAPHORE register shadowed in the
config-space may not reflect the correct POST stage after
an EEH reset in BE2/3; it may return FW_READY state even though
FW is not ready. This causes the driver to prematurely
poll the FW mailbox and fail.
For BE2/3 use the CSR-BAR/0xac instead.
Reported-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
Fix regressions introduced by the last set of fixes (sorry):
1. Potential deadlock when disabling TX queues.
2. RX was broken on architectures other than x86 and powerpc.
I still expect to send one more bug fix for 3.9, but as it sometimes
takes days to reproduce the bug it's going to take a couple of weeks of
testing to be confident that it's really fixed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
RX DMA buffers start at an offset of EFX_PAGE_IP_ALIGN bytes from the
start of a cache line. This offset obviously needs to be included in
the virtual address, but this was missed in commit b590ace09d
('sfc: Fix efx_rx_buf_offset() in the presence of swiotlb') since
EFX_PAGE_IP_ALIGN is equal to 0 on both x86 and powerpc.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
efx_device_detach_sync() locks all TX queues before marking the device
detached and thus disabling further TX scheduling. But it can still
be interrupted by TX completions which then result in TX scheduling in
soft interrupt context. This will deadlock when it tries to acquire
a TX queue lock that efx_device_detach_sync() already acquired.
To avoid deadlock, we must use netif_tx_{,un}lock_bh().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
While PCI card faces EEH errors, reset (usually hot reset) is
expected to recover from the EEH errors. After EEH core finishes
the reset, the driver callback (be_eeh_reset) is called and wait
the firmware to complete POST successfully. The original code would
return with error once detecting failure during POST stage. That
seems not enough.
The patch forces the driver (be_eeh_reset) to wait the firmware
completes POST until timeout, instead of returning error upon
detection POST failure immediately. Also, it would improve the
reliability of the EEH funtionality of the driver.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Acked-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should reset nf settings bond to the skb as ipip/ipgre do.
If not, the conntrack/nat info bond to the origin packet may continually
redirect the packet to vxlan interface causing a routing loop.
this is the scenario:
VETP VXLAN Gateway
/----\ /---------------\
| | | |
| vx+--+vx --NAT-> eth0+--> Internet
| | | |
\----/ \---------------/
when there are any packet coming from internet to the vetp, there will be lots
of garbage packets coming out the gateway's vxlan interface, but none actually
sent to the physical interface, because they are redirected back to the vxlan
interface in the postrouting chain of NAT rule, and dmesg complains:
Mar 1 21:52:53 debian kernel: [ 8802.997699] Dead loop on virtual device vxlan0, fix it urgently!
Mar 1 21:52:54 debian kernel: [ 8804.004907] Dead loop on virtual device vxlan0, fix it urgently!
Mar 1 21:52:55 debian kernel: [ 8805.012189] Dead loop on virtual device vxlan0, fix it urgently!
Mar 1 21:52:56 debian kernel: [ 8806.020593] Dead loop on virtual device vxlan0, fix it urgently!
the patch should fix the problem
Signed-off-by: Zang MingJie <zealot0630@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
===================
This series contains fixes to e1000e and igb.
The e1000e fix resolves an issue at 1000Mbps link speed, where one of the
MAC's internal clocks can be stopped for up to 4us when entering K1 (a
power mode of the MAC-PHY interconnect). If the MAC is waiting for
completion indications for 2 DMA write requests into Host memory
(e.g. descriptor writeback or Rx packet writing) and the
indications occur while the clock is stopped, both indications will be
missed by the MAC causing the MAC to wait for the completion indications
and be unable to generate further DMA write requests. This results in an
apparent hardware hang. The patch works-around the issue by disabling
the de-assertion of the clock request when 1000Mbps link is acquired (K1
must be disabled while doing this).
The igb fix to drop BUILD_BUG_ON check from igb_build_rx_buffer resolves
a build error on s390 devices. The igb driver was throwing a build error
due to the fact that a frame built using build_skb would be larger than 2K.
Since this is not likely to change at any point in the future we are better
off just dropping the check since we already had a check in
igb_set_rx_buffer_len that will just disable the usage of build_skb anyway.
The igb fix for i210 link setup changes the setup copper link function
to use a switch statement, so that the appropriate setup link function
is called for the given PHY types.
Lastly, the igb fix for a lockdep issue in igb_get_i2c_client resolves
the issue by re-factoring the initialization and usage of the i2c_client.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"A moderately sized pile of fixes, some specifically for merge window
introduced regressions although others are for longer standing items
and have been queued up for -stable.
I'm kind of tired of all the RDS protocol bugs over the years, to be
honest, it's way out of proportion to the number of people who
actually use it.
1) Fix missing range initialization in netfilter IPSET, from Jozsef
Kadlecsik.
2) ieee80211_local->tim_lock needs to use BH disabling, from Johannes
Berg.
3) Fix DMA syncing in SFC driver, from Ben Hutchings.
4) Fix regression in BOND device MAC address setting, from Jiri
Pirko.
5) Missing usb_free_urb in ISDN Hisax driver, from Marina Makienko.
6) Fix UDP checksumming in bnx2x driver for 57710 and 57711 chips,
fix from Dmitry Kravkov.
7) Missing cfgspace_lock initialization in BCMA driver.
8) Validate parameter size for SCTP assoc stats getsockopt(), from
Guenter Roeck.
9) Fix SCTP association hangs, from Lee A Roberts.
10) Fix jumbo frame handling in r8169, from Francois Romieu.
11) Fix phy_device memory leak, from Petr Malat.
12) Omit trailing FCS from frames received in BGMAC driver, from Hauke
Mehrtens.
13) Missing socket refcount release in L2TP, from Guillaume Nault.
14) sctp_endpoint_init should respect passed in gfp_t, rather than use
GFP_KERNEL unconditionally. From Dan Carpenter.
15) Add AISX AX88179 USB driver, from Freddy Xin.
16) Remove MAINTAINERS entries for drivers deleted during the merge
window, from Cesar Eduardo Barros.
17) RDS protocol can try to allocate huge amounts of memory, check
that the user's request length makes sense, from Cong Wang.
18) SCTP should use the provided KMALLOC_MAX_SIZE instead of it's own,
bogus, definition. From Cong Wang.
19) Fix deadlocks in FEC driver by moving TX reclaim into NAPI poll,
from Frank Li. Also, fix a build error introduced in the merge
window.
20) Fix bogus purging of default routes in ipv6, from Lorenzo Colitti.
21) Don't double count RTT measurements when we leave the TCP receive
fast path, from Neal Cardwell."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (61 commits)
tcp: fix double-counted receiver RTT when leaving receiver fast path
CAIF: fix sparse warning for caif_usb
rds: simplify a warning message
net: fec: fix build error in no MXC platform
net: ipv6: Don't purge default router if accept_ra=2
net: fec: put tx to napi poll function to fix dead lock
sctp: use KMALLOC_MAX_SIZE instead of its own MAX_KMALLOC_SIZE
rds: limit the size allocated by rds_message_alloc()
MAINTAINERS: remove eexpress
MAINTAINERS: remove drivers/net/wan/cycx*
MAINTAINERS: remove 3c505
caif_dev: fix sparse warnings for caif_flow_cb
ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver
sctp: use the passed in gfp flags instead GFP_KERNEL
ipv[4|6]: correct dropwatch false positive in local_deliver_finish
l2tp: Restore socket refcount when sendmsg succeeds
net/phy: micrel: Disable asymmetric pause for KSZ9021
bgmac: omit the fcs
phy: Fix phy_device_free memory leak
bnx2x: Fix KR2 work-around condition
...
This patch fixes a lockdep warning in igb_get_i2c_client by
refactoring the initialization and usage of the i2c_client
completely. There is no on the fly allocation of the single
client needed today.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the setup copper link function to use a switch
statement for the PHY id's available for the given PHY types. It
also adds a case for the I210 PHY id, so the appropriate setup link
function is called for it.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On s390 the igb driver was throwing a build error due to the fact that a frame
built using build_skb would be larger than 2K. Since this is not likely to
change at any point in the future we are better off just dropping the check
since we already had a check in igb_set_rx_buffer_len that will just disable
the usage of build_skb anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
At 1000Mbps link speed, one of the MAC's internal clocks can be stopped for
up to 4us when entering K1 (a power mode of the MAC-PHY interconnect). If
the MAC is waiting for completion indications for 2 DMA write requests into
Host memory (e.g. descriptor writeback or Rx packet writing) and the
indications occur while the clock is stopped, both indications will be
missed by the MAC causing the MAC to wait for the completion indications
and be unable to generate further DMA write requests. This results in an
apparent hardware hang.
Work-around the issue by disabling the de-assertion of the clock request
when 1000Mbps link is acquired (K1 must be disabled while doing this).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
build error cause by
Commit ff43da86c6
("NET: FEC: dynamtic check DMA desc buff type")
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_get_nextdesc’:
drivers/net/ethernet/freescale/fec.c:215:18: error: invalid use of undefined type ‘struct bufdesc_ex’
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_get_prevdesc’:
drivers/net/ethernet/freescale/fec.c:224:18: error: invalid use of undefined type ‘struct bufdesc_ex’
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_start_xmit’:
drivers/net/ethernet/freescale/fec.c:286:37: error: arithmetic on pointer to an incomplete type
drivers/net/ethernet/freescale/fec.c:287:13: error: arithmetic on pointer to an incomplete type
drivers/net/ethernet/freescale/fec.c:324:7: error: dereferencing pointer to incomplete type etc....
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This flow happens when we get a failed single Tx response
on an AMPDU queue. In this case, the frame won't be sent
any more. So we need to move the window on the recipient
side. This is done by a BAR.
Now if we are in the following case: 10, 12 and 13 are ACKed
and 11 isn't.
10 11 12 13.
V X V V
Then, 11 will be sent 16 times as an MPDU (as oppsed to
A-MPDU). If this failed, we are entering the flow described
above. So we need to send a BAR with ssn = 12.
But in this case, the scheduler will tell us to free frames
up to 13 (included).
So, it is perfectly possible to get a failed single Tx
response on an AMPDU queue that makes the scheduler's ssn
jump by more than 1 single packet.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the rssi more accurate by taking in count per-chain AGC
values. Without this, the RSSI reports inaccurate values.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the device is being restarted, all the Rx / Tx Block
Ack sessions are been wiped out by the driver. So ignore
the requests from mac80211 that stops Tx agg while
reconfiguring the device.
Note that stopping a non-existing Rx BA session is harmless,
so just honor mac80211's request.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fix removes the override of calibration request values sent
to the FW.
Due to that, the sending of default values to now implemented
calibrations is removed.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The phy_cfg is given from the TLV value and does not have to be
built by us.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We must set the valid TX antennas number in the ucode before
sending the phy_cfg_cmd and request for calibrations.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This situation is clearly an error situation and the only
way to recover is to restart the driver / fw.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is a resubmission.
Added kfree() in ax88179_get_eeprom to prevent memory leakage.
Modified "__le16 rxctl" to "u16 rxctl" in "struct ax88179_data" and removed pointless casts.
Removed asix_init and asix_exit functions and added "module_usb_driver(ax88179_178a_driver)".
Fixed endianness issue on big endian systems and verified this driver on iBook G4.
Removed steps that change net->features in ax88179_set_features function.
Added "const" to ethtool_ops structure and fixed the coding style of AX88179_BULKIN_SIZE array.
Fixed the issue that the default MTU is not 1500.
Added ax88179_change_mtu function and enabled the hardware jumbo frame function to support an
MTU higher than 1500.
Fixed indentation and empty line coding style errors.
The _nopm version usb functions were added to access register in suspend and resume functions.
Serveral variables allocted dynamically were removed and replaced by stack variables.
ax88179_get_eeprom were modified from asix_get_eeprom in asix_common.
This patch adds a driver for ASIX's AX88179 family of USB 3.0/2.0
to gigabit ethernet adapters. It's based on the AX88xxx driver but
the usb commands used to access registers for AX88179 are completely different.
This driver had been verified on x86 system with AX88179/AX88178A and
Sitcomm LN-032 USB dongles.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull MIPS updates from Ralf Baechle:
o Add basic support for the Mediatek/Ralink Wireless SoC family.
o The Qualcomm Atheros platform is extended by support for the new
QCA955X SoC series as well as a bunch of patches that get the code
ready for OF support.
o Lantiq and BCM47XX platform have a few improvements and bug fixes.
o MIPS has sent a few patches that get the kernel ready for the
upcoming microMIPS support.
o The rest of the series is made up of small bug fixes and cleanups
that relate to various parts of the MIPS code. The biggy in there is
a whitespace cleanup. After I was sent another set of whitespace
cleanup patches I decided it was the time to clean the whitespace
"issues" for once and and that touches many files below arch/mips/.
Fix up silly conflicts, mostly due to whitespace cleanups.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (105 commits)
MIPS: Quit exporting kernel internel break codes to uapi/asm/break.h
MIPS: remove broken conditional inside vpe loader code
MIPS: SMTC: fix implicit declaration of set_vi_handler
MIPS: early_printk: drop __init annotations
MIPS: Probe for and report hardware virtualization support.
MIPS: ath79: add support for the Qualcomm Atheros AP136-010 board
MIPS: ath79: add USB controller registration code for the QCA955X SoCs
MIPS: ath79: add PCI controller registration code for the QCA955X SoCs
MIPS: ath79: add WMAC registration code for the QCA955X SoCs
MIPS: ath79: register UART for the QCA955X SoCs
MIPS: ath79: add QCA955X specific glue to ath79_device_reset_{set, clear}
MIPS: ath79: add GPIO setup code for the QCA955X SoCs
MIPS: ath79: add IRQ handling code for the QCA955X SoCs
MIPS: ath79: add clock setup code for the QCA955X SoCs
MIPS: ath79: add SoC detection code for the QCA955X SoCs
MIPS: ath79: add early printk support for the QCA955X SoCs
MIPS: ath79: fix WMAC IRQ resource assignment
mips: reserve elfcorehdr
mips: Make sure kernel memory is in iomem
MIPS: ath79: use dynamically allocated USB platform devices
...
Phyter KSZ9021 has hardware bug. If asymmetric pause is enabled,
then it is necessary to disconnect and then reconnect the ethernet
cable to get the phyter working. The solution is to disable the
asymmetric pause.
Signed-off-by: Vlastimil Kosar <ikosar@fit.vutbr.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not include the frame check sequence when adding the skb to
netif_receive_skb(). This causes problems when this interface was
bridged to a wifi ap and a big package should be forwarded from this
Ethernet driver through a bride to the wifi client.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix memory leak in phy_device_free() for the case when phy_device*
returned by phy_device_create() is not registered in the system.
Bug description:
phy_device_create() sets name of kobject using dev_set_name(), which
allocates memory using kvasprintf(), but this memory isn't freed if
the underlying device isn't registered properly, because kobject_cleanup()
is not called in that case. This can happen (and actually is happening on
our machines) if phy_device_register(), called by mdiobus_scan(), fails.
Patch description:
Embedded struct device is initialized in phy_device_create() and it
counterpart phy_device_free() just drops one reference to the device,
which leads to proper deinitialization including releasing the kobject
name memory.
Signed-off-by: Petr Malat <oss@malat.biz>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Oostdyk