The UniPro specification states that attribute IDs of the following
parameters are vendor-specific so some SoCs could have no regions at the
defined addresses:
- DME_LocalFC0ProtectionTimeOutVal
- DME_LocalTC0ReplayTimeOutVal
- DME_LocalAFC0ReqTimeOutVal
In addition, the following parameters should be set considering the
compatibility between host and device.
- PA_PWRMODEUSERDATA0
- PA_PWRMODEUSERDATA1
- PA_PWRMODEUSERDATA2
- PA_PWRMODEUSERDATA3
- PA_PWRMODEUSERDATA4
- PA_PWRMODEUSERDATA5
Introduce a quirk to allow vendor drivers to override the UniPro defaults.
Link: https://lore.kernel.org/r/1fedd3dea0ccc980913a5995a10510d86a5b01b9.1608513782.git.kwmad.kim@samsung.com
Acked-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current flush location does not guarantee disabling BKOPS for the case
of requesting device power off.
1) The exceptional event handler is queued
2) ufs suspend starts with a request of device power off
3) BKOPS is disabled in ufs suspend
4) The queued work for the handler is done and BKOPS is re-enabled
Relocate the flush statement to ensure BKOPS remain disabled.
Link: https://lore.kernel.org/r/1608360039-16390-1-git-send-email-kwmad.kim@samsung.com
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Flush during hibern8 is sufficient on MediaTek platforms, thus enable
UFSHCI_QUIRK_SKIP_MANUAL_WB_FLUSH_CTRL to skip enabling
fWriteBoosterBufferFlush during WriteBooster initialization.
Link: https://lore.kernel.org/r/20201222072928.32328-1-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFSHCI_QUIRK_SKIP_MANUAL_WB_FLUSH_CTRL is intended to skip enabling
fWriteBoosterBufferFlushEn while WriteBooster is initializing. Therefore
it is better to apply the checking during WriteBooster initialization only.
Link: https://lore.kernel.org/r/20201222072905.32221-3-stanley.chu@mediatek.com
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if device needs to do flush or BKOP operations, the device VCC
power is kept during runtime-suspend period.
However, if system suspend is happening while device is runtime-suspended,
such power may not be disabled successfully.
The reasons may be,
1. If current PM level is the same as SPM level, device will keep
runtime-suspended by ufshcd_system_suspend().
2. Flush recheck work may not be scheduled successfully during system
suspend period. If it can wake up the system, this is also not the
intention of the recheck work.
To fix this issue, simply runtime-resume the device if the flush is allowed
during runtime suspend period. Flush capability will be disabled while
leaving runtime suspend, and also not be allowed in system suspend period.
Link: https://lore.kernel.org/r/20201222072905.32221-2-stanley.chu@mediatek.com
Fixes: 51dd905bd2 ("scsi: ufs: Fix WriteBooster flush during runtime suspend")
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a load of driver fixes (12 ufs, 1 mpt3sas, 1 cxgbi). The big
core two fixes are for power management ("block: Do not accept any
requests while suspended" and "block: Fix a race in the runtime power
management code") which finally sorts out the resume problems we've
occasionally been having. To make the resume fix, there are seven
necessary precursors which effectively renames REQ_PREEMPT to REQ_PM,
so every "special" request in block is automatically a power
management exempt one. All of the non-PM preempt cases are removed
except for the one in the SCSI Parallel Interface (spi) domain
validation which is a genuine case where we have to run requests at
high priority to validate the bus so this becomes an autopm get/put
protected request.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCX+98LyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYvLAP9K+HBT
Lrkt3VWc9gq6F36+QH/SeW8IyXGaj77ysFHXxwD/UambRjRK8IA24mvf9sWeLLj6
p8CqCHUkCXqP48IiymE=
=NHrx
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a load of driver fixes (12 ufs, 1 mpt3sas, 1 cxgbi).
The big core two fixes are for power management ("block: Do not accept
any requests while suspended" and "block: Fix a race in the runtime
power management code") which finally sorts out the resume problems
we've occasionally been having.
To make the resume fix, there are seven necessary precursors which
effectively renames REQ_PREEMPT to REQ_PM, so every "special" request
in block is automatically a power management exempt one.
All of the non-PM preempt cases are removed except for the one in the
SCSI Parallel Interface (spi) domain validation which is a genuine
case where we have to run requests at high priority to validate the
bus so this becomes an autopm get/put protected request"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (22 commits)
scsi: cxgb4i: Fix TLS dependency
scsi: ufs: Un-inline ufshcd_vops_device_reset function
scsi: ufs: Re-enable WriteBooster after device reset
scsi: ufs-mediatek: Use correct path to fix compile error
scsi: mpt3sas: Signedness bug in _base_get_diag_triggers()
scsi: block: Do not accept any requests while suspended
scsi: block: Remove RQF_PREEMPT and BLK_MQ_REQ_PREEMPT
scsi: core: Only process PM requests if rpm_status != RPM_ACTIVE
scsi: scsi_transport_spi: Set RQF_PM for domain validation commands
scsi: ide: Mark power management requests with RQF_PM instead of RQF_PREEMPT
scsi: ide: Do not set the RQF_PREEMPT flag for sense requests
scsi: block: Introduce BLK_MQ_REQ_PM
scsi: block: Fix a race in the runtime power management code
scsi: ufs-pci: Enable UFSHCD_CAP_RPM_AUTOSUSPEND for Intel controllers
scsi: ufs-pci: Fix recovery from hibernate exit errors for Intel controllers
scsi: ufs-pci: Ensure UFS device is in PowerDown mode for suspend-to-disk ->poweroff()
scsi: ufs-pci: Fix restore from S4 for Intel controllers
scsi: ufs-mediatek: Keep VCC always-on for specific devices
scsi: ufs: Allow regulators being always-on
scsi: ufs: Clear UAC for RPMB after ufshcd resets
...
This series consists of the usual driver updates (ufs, qla2xxx,
smartpqi, target, zfcp, fnic, mpt3sas, ibmvfc) plus a load of
cleanups, a major power management rework and a load of assorted minor
updates. There are a few core updates (formatting fixes being the big
one) but nothing major this cycle.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCX9o0KSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbOZAP9D5NTN
J7dJUo2MIMy84YBu+d9ag7yLlNiRWVY2yw5vHwD/Z7JjAVLwz/tzmyjU9//o2J6w
hwhOv6Uto89gLCWSEz8=
=KUPT
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This consists of the usual driver updates (ufs, qla2xxx, smartpqi,
target, zfcp, fnic, mpt3sas, ibmvfc) plus a load of cleanups, a major
power management rework and a load of assorted minor updates.
There are a few core updates (formatting fixes being the big one) but
nothing major this cycle"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (279 commits)
scsi: mpt3sas: Update driver version to 36.100.00.00
scsi: mpt3sas: Handle trigger page after firmware update
scsi: mpt3sas: Add persistent MPI trigger page
scsi: mpt3sas: Add persistent SCSI sense trigger page
scsi: mpt3sas: Add persistent Event trigger page
scsi: mpt3sas: Add persistent Master trigger page
scsi: mpt3sas: Add persistent trigger pages support
scsi: mpt3sas: Sync time periodically between driver and firmware
scsi: qla2xxx: Update version to 10.02.00.104-k
scsi: qla2xxx: Fix device loss on 4G and older HBAs
scsi: qla2xxx: If fcport is undergoing deletion complete I/O with retry
scsi: qla2xxx: Fix the call trace for flush workqueue
scsi: qla2xxx: Fix flash update in 28XX adapters on big endian machines
scsi: qla2xxx: Handle aborts correctly for port undergoing deletion
scsi: qla2xxx: Fix N2N and NVMe connect retry failure
scsi: qla2xxx: Fix FW initialization error on big endian machines
scsi: qla2xxx: Fix crash during driver load on big endian machines
scsi: qla2xxx: Fix compilation issue in PPC systems
scsi: qla2xxx: Don't check for fw_started while posting NVMe command
scsi: qla2xxx: Tear down session if FW say it is down
...
More and more statements are being added to ufshcd_vops_device_reset() and
this function is being called from multiple locations in the driver.
Un-inline the function to allow the compiler to make better decisions.
Link: https://lore.kernel.org/r/20201208135635.15326-3-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS 3.1 specification mentions that the WriteBooster flags listed below
will be set to their default values, i.e. disabled, after power cycle or
any type of reset event. Thus we need to reset the flag variables kept in
struct hba to align with the device status and ensure that
WriteBooster-related functions are configured properly after device reset.
Without this fix, WriteBooster will not be enabled successfully after by
ufshcd_wb_ctrl() after device reset because hba->wb_enabled remains true.
Flags required to be reset to default values:
- fWriteBoosterEn: hba->wb_enabled
- fWriteBoosterBufferFlushEn: hba->wb_buf_flush_enabled
- fWriteBoosterBufferFlushDuringHibernate: No variable mapped
Link: https://lore.kernel.org/r/20201208135635.15326-2-stanley.chu@mediatek.com
Fixes: 3d17b9b5ab ("scsi: ufs: Add write booster feature support")
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the kernel is compiled with allmodconfig, the following error is
reported:
In file included from drivers/scsi/ufs/ufs-mediatek-trace.h:36:0,
from drivers/scsi/ufs/ufs-mediatek.c:28:
./include/trace/define_trace.h:95:42: fatal error: ./ufs-mediatek-trace.h: No such file or directory
#include TRACE_INCLUDE(TRACE_INCLUDE_FILE)
The comment in include/trace/define_trace.h specifies that:
TRACE_INCLUDE_PATH: Note, the path is relative to define_trace.h, not the
file including it. Full path names for out of tree modules must be used.
So without "CFLAGS_ufs-mediatek.o := -I$(src)", the current directory "."
is "include/trace/", the relative path of ufs-mediatek-trace.h is
"../../drivers/scsi/ufs/".
Link: https://lore.kernel.org/r/20201209063144.1840-2-thunder.leizhen@huawei.com
Fixes: ca1bb061d6 ("scsi: ufs-mediatek: Introduce event_notify implementation")
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Intel controllers can end up in an unrecoverable state after a hibernate
exit error unless a full reset and restore is done before anything else.
Force that to happen.
Link: https://lore.kernel.org/r/20201207083120.26732-4-adrian.hunter@intel.com
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The expectation for suspend-to-disk is that devices will be powered-off, so
the UFS device should be put in PowerDown mode. If spm_lvl is not 5, then
that will not happen. Change the pm callbacks to force spm_lvl 5 for
suspend-to-disk poweroff.
Link: https://lore.kernel.org/r/20201207083120.26732-3-adrian.hunter@intel.com
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, ufshcd-pci is the only UFS driver with support for
suspend-to-disk PM callbacks (i.e. freeze/thaw/restore/poweroff). These
callbacks are set by the macro SET_SYSTEM_SLEEP_PM_OPS to the same
functions as system suspend/resume. That will work with spm_lvl 5 because
spm_lvl 5 will result in a full restore for the ->restore() callback. In
the absence of a full restore, the host controller registers will have
values set up by the restore kernel (the kernel that boots and loads the
restore image) which are not necessarily the same. However it turns out,
the only registers that sometimes need restore are the base address
registers. This has gone un-noticed because, depending on IOMMU settings,
the kernel can end up allocating the same addresses every time.
For Intel controllers, an spm_lvl other than 5 can be used, so to support
S4 (suspend-to-disk) with spm_lvl other than 5, restore the base address
registers.
Link: https://lore.kernel.org/r/20201207083120.26732-2-adrian.hunter@intel.com
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For some devices which need extra delay after VCC power down, VCC shall be
kept always-on in some MediaTek UFS platforms to ensure the stability of
such devices because the extra delay may not be enough in those platforms.
Link: https://lore.kernel.org/r/20201207054955.24366-3-stanley.chu@mediatek.com
Reviewed-by: Andy Teng <andy.teng@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce a flag "always_on" in struct ufs_vreg to allow vendors to keep
the regulator always-on.
Link: https://lore.kernel.org/r/20201207054955.24366-2-stanley.chu@mediatek.com
Reviewed-by: Andy Teng <andy.teng@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If RPMB is not provisioned, we may see RPMB failure after UFS
suspend/resume. Inject request_sense to clear uac in ufshcd reset flow.
Link: https://lore.kernel.org/r/20201201041402.3860525-1-jaegeuk@kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Randall Huang <huangrandall@google.com>
Signed-off-by: Leo Liou <leoliou@google.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change dev_err() print message from "dme-reset" to "dme_enable" in function
ufshcd_dme_enable().
Link: https://lore.kernel.org/r/20201207190137.6858-3-huobean@gmail.com
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
POWER_DESC_MAX_SIZE is unused, remove it.
Link: https://lore.kernel.org/r/20201207190137.6858-2-huobean@gmail.com
Acked-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
clang complains about a possible code path in which a variable is used
without an initialization:
drivers/scsi/ufs/ufshcd.c:7690:3: error: variable 'sdp' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized]
BUG_ON(1);
^~~~~~~~~
include/asm-generic/bug.h:63:36: note: expanded from macro 'BUG_ON'
#define BUG_ON(condition) do { if (unlikely(condition)) BUG(); } while (0)
^~~~~~~~~~~~~~~~~~~
Turn the BUG_ON(1) into an unconditional BUG() that makes it clear to clang
that this code path is never hit.
Link: https://lore.kernel.org/r/20201203223137.1205933-1-arnd@kernel.org
Fixes: 4f3e900b62 ("scsi: ufs: Clear UAC for FFU and RPMB LUNs")
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Invalidation check of arguments should have been checked before
ufshcd_hold(). This can help to prevent ufshcd_hold()/ ufshcd_release()
from being invoked unnecessarily.
[mkp: removed unused out: labels]
Link: https://lore.kernel.org/r/1606973132-5937-1-git-send-email-user@jang-Samsung-DeskTop-System
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: jintae jang <jt77.jang@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dump registers and states prior to leaving IRQ handler when an AH8 error
occurs.
Link: https://lore.kernel.org/r/1606910644-21185-4-git-send-email-cang@codeaurora.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bao D. Nguyen <nguyenb@codeaurora.org>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In current task abort routine, if task abort happens to the device W-LUN,
the code directly jumps to ufshcd_eh_host_reset_handler() to perform a full
reset and restore then returns FAIL or SUCCESS. Commands sent to the device
W-LUN are most likely the SSU cmds sent during UFS PM operations. If such
SSU cmd enters task abort routine when ufshcd_eh_host_reset_handler()
flushes eh_work, it will get stuck there since err_handler is serialized
with PM operations.
In order to unblock above call path, we merely clean up the lrb taken by
this cmd, queue the eh_work and return SUCCESS. Once the cmd is aborted,
the PM operation which sends out the cmd just errors out, then err_handler
shall be able to proceed with the full reset and restore.
In this scenario, the cmd is aborted even before it is actually cleared by
HW, set the lrb->in_use flag to prevent subsequent cmds, including SCSI
cmds and dev cmds, from taking the lrb released from abort. The flag shall
evetually be cleared in __ufshcd_transfer_req_compl() invoked by the full
reset and restore from err_handler.
[mkp: conflict with event logging series]
Link: https://lore.kernel.org/r/1606910644-21185-3-git-send-email-cang@codeaurora.org
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Serialize eh_work with system PM events and async scan to make sure eh_work
does not run in parallel with them.
Link: https://lore.kernel.org/r/1606910644-21185-2-git-send-email-cang@codeaurora.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS specficication allows different VCC configurations for UFS devices,
for example:
(1). 2.70V - 3.60V (Activated by default in UFS core driver)
(2). 1.70V - 1.95V (Activated if "vcc-supply-1p8" is declared in
device tree)
(3). 2.40V - 2.70V (Supported since UFS 3.x)
With the introduction of UFS 3.x products, an issue is happening that UFS
driver will use wrong "min_uV-max_uV" values to configure the voltage of
VCC regulator on UFU 3.x products with the configuration (3) used.
To solve this issue, we simply remove pre-defined initial VCC voltage
values in UFS core driver with below reasons,
1. UFS specifications do not define how to detect the VCC configuration
supported by attached device.
2. Device tree already supports standard regulator properties.
Therefore VCC voltage shall be defined correctly in device tree, and shall
not changed by UFS driver. What UFS driver needs to do is simply enable or
disable the VCC regulator only.
Similar change is applied to VCCQ and VCCQ2 as well.
Note that we keep struct ufs_vreg unchanged. This allows vendors to
configure proper min_uV and max_uV of any regulators to make
regulator_set_voltage() works during regulator toggling flow in the
future. Without specific vendor configurations, min_uV and max_uV will be
NULL by default and UFS core driver will enable or disable the regulator
only without adjusting its voltage.
Link: https://lore.kernel.org/r/20201202091819.22363-1-stanley.chu@mediatek.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use phy_initialization helper instead of direct invocation.
Link: https://lore.kernel.org/r/20201205120041.26869-5-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use phy_initialization helper instead of direct function invocation.
Link: https://lore.kernel.org/r/20201205120041.26869-4-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce phy_initialization helper since this is the only one variant
function without helper.
Link: https://lore.kernel.org/r/20201205120041.26869-3-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since setup_regulators variant function is not used by any vendors, simply
remove it.
Link: https://lore.kernel.org/r/20201205120041.26869-2-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce event_notify implementation on MediaTek UFS platform. A
vendor-specific tracepoint is added that can be used for debugging
purposes.
Link: https://lore.kernel.org/r/20201205115901.26815-5-stanley.chu@mediatek.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce event_notify variant function to allow vendor to get notification
of important events and connect to any proprietary debugging facilities.
Link: https://lore.kernel.org/r/20201205115901.26815-4-stanley.chu@mediatek.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The UFS error history does not only have "history of errors" but also a
log of some other events which are not defined as errors.
This patch fixes the confused naming of related functions and changes the
approach for updating and printing history in preparation of next patch.
This patch does not change any functionality.
Link: https://lore.kernel.org/r/20201205115901.26815-3-stanley.chu@mediatek.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add error history for abort event in UFS Device W-LUN.
Use specified value as parameter of ufshcd_update_reg_hist() to identify
the aborted tag or LUNs.
Link: https://lore.kernel.org/r/20201205115901.26815-2-stanley.chu@mediatek.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of hardcoding the scale down gear, make it a member of
the ufs_clk_scaling struct.
Link: https://lore.kernel.org/r/1606442334-22641-1-git-send-email-cang@codeaurora.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If we want to disable clocks to save power but still keep the link active,
core_clk_unipro, like ref_clk, should not be the one being disabled.
Link: https://lore.kernel.org/r/1606356063-38380-3-git-send-email-cang@codeaurora.org
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove the param skip_ref_clk from __ufshcd_setup_clocks(), but keep a flag
in struct ufs_clk_info to tell whether a clock can be disabled or not while
the link is active.
Link: https://lore.kernel.org/r/1606356063-38380-2-git-send-email-cang@codeaurora.org
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the case that auto_bkops_enable is false, which means auto bkops has
been disabled, there is no need to call ufshcd_disable_auto_bkops().
Link: https://lore.kernel.org/r/20201125185300.3394-1-huobean@gmail.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The introduction of ufshcd_dme_configure_adapt() refactored out duplication
from the Mediatek and Qualcomm drivers.
Both these implementations had the logic of:
gear_tx == UFS_HS_G4 => PA_INITIAL_ADAPT
gear_tx != UFS_HS_G4 => PA_NO_ADAPT
but now both implementations pass PA_INITIAL_ADAPT as "adapt_val" and if
gear_tx is not UFS_HS_G4 that is replaced with PA_INITIAL_ADAPT. In other
words, it's PA_INITIAL_ADAPT in both above cases.
The result is that e.g. Qualcomm SM8150 has no longer functional UFS, so
adjust the logic to match the previous implementation.
Link: https://lore.kernel.org/r/20201121044810.507288-1-bjorn.andersson@linaro.org
Fixes: fc85a74e28 ("scsi: ufs: Refactor ADAPT configuration function")
Reviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If UFS host device is in runtime-suspended state while UFS shutdown
callback is invoked, UFS device shall be resumed for register
accesses. Currently only UFS local runtime resume function will be invoked
to wake up the host. This is not enough because if someone triggers
runtime resume from block layer, then race may happen between shutdown and
runtime resume flow, and finally lead to unlocked register access.
To fix this, in ufshcd_shutdown(), use pm_runtime_get_sync() instead of
resuming UFS device by ufshcd_runtime_resume() "internally" to let runtime
PM framework manage the whole resume flow.
Link: https://lore.kernel.org/r/20201119062916.12931-1-stanley.chu@mediatek.com
Fixes: 57d104c153 ("ufs: add UFS power management support")
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We have LBA and length for unmap commands.
Link: https://lore.kernel.org/r/20201117165839.1643377-8-jaegeuk@kernel.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Leo Liou <leoliou@google.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The following call stack prevents clk_gating at every I/O completion. We
can remove the condition, ufshcd_any_tag_in_use(), since clkgating_work
will check it again.
ufshcd_complete_requests(struct ufs_hba *hba)
ufshcd_transfer_req_compl()
__ufshcd_transfer_req_compl()
__ufshcd_release(hba)
if (ufshcd_any_tag_in_use() == 1)
return;
ufshcd_tmc_handler(hba);
blk_mq_tagset_busy_iter();
Note that this still requires work to deal with a potential race condition
when user sets clkgating.delay_ms to very small value. That can cause
preventing clkgating by the check of ufshcd_any_tag_in_use() in gate_work.
Link: https://lore.kernel.org/r/20201117165839.1643377-7-jaegeuk@kernel.org
Fixes: 7252a36030 ("scsi: ufs: Avoid busy-waiting by eliminating tag conflicts")
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This adds user-friendly tracepoints with group id.
Link: https://lore.kernel.org/r/20201117165839.1643377-6-jaegeuk@kernel.org
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Must have WQ_MEM_RECLAIM
``WQ_MEM_RECLAIM``
All workqueues which might be used in the memory reclaim paths **MUST**
have this flag set. The wq is guaranteed to have at least one execution
context regardless of memory pressure.
Link: https://lore.kernel.org/r/20201117165839.1643377-5-jaegeuk@kernel.org
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In order to conduct FFU or RPMB operations, UFS needs to clear UNIT
ATTENTION condition. Clear it explicitly so that we get no failures during
initialization.
Link: https://lore.kernel.org/r/20201117165839.1643377-4-jaegeuk@kernel.org
Signed-off-by: Jaegeuk Kim <jaegeuk@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While running a stress test which enables/disables clkgating, we
occasionally hit device timeout. This patch avoids a subtle race condition
to address it.
Link: https://lore.kernel.org/r/20201117165839.1643377-3-jaegeuk@kernel.org
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Once UFS is gated with CLKS_OFF, it should not call REQ_CLKS_OFF
again. This can lead to hibern8_enter failure.
Link: https://lore.kernel.org/r/20201117165839.1643377-2-jaegeuk@kernel.org
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If someone plays with the UFS clk scaling devfreq governor through sysfs,
ufshcd_devfreq_scale may be called even when HBA is not runtime ACTIVE.
This can lead to unexpected error. We cannot just protect it by calling
pm_runtime_get_sync() because that may cause a race condition since HBA
runtime suspend ops need to suspend clk scaling. To fix this call
pm_runtime_get_noresume() and check HBA's runtime status. Only proceed if
HBA is runtime ACTIVE, otherwise just bail.
governor_store
devfreq_performance_handler
update_devfreq
devfreq_set_target
ufshcd_devfreq_target
ufshcd_devfreq_scale
Link: https://lore.kernel.org/r/1600758548-28576-1-git-send-email-cang@codeaurora.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
WB-related sysfs entries can be accessed even when an UFS device does not
support the feature. The descriptors which are not supported by the UFS
device may be wrongly reported when they are accessed from their
corrsponding sysfs entries. Fix it by adding a sanity check of parameter
offset against the actual decriptor length.
Link: https://lore.kernel.org/r/1603346348-14149-1-git-send-email-cang@codeaurora.org
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Acked-by: Daejun Park <daejun7.park@samsung.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use common ADAPT configuration function to reduce duplicated code in UFS
drivers.
Link: https://lore.kernel.org/r/20201116065054.7658-10-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use common ADAPT configuration function to reduce duplicated code in UFS
drivers.
Link: https://lore.kernel.org/r/20201116065054.7658-9-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Several vendors are using same code to configure ADAPT settings for
HS-G4. Simply refactor it as common function.
Link: https://lore.kernel.org/r/20201116065054.7658-8-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use common device parameter initialization function instead of initializing
those parameters by vendor driver itself.
Link: https://lore.kernel.org/r/20201116065054.7658-7-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use common device parameter initialization function instead of initializing
those parameters by vendor driver itself.
Link: https://lore.kernel.org/r/20201116065054.7658-6-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use common device parameter initialization function instead of initializing
those parameters by vendor driver itself.
Link: https://lore.kernel.org/r/20201116065054.7658-5-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use common device parameter initialization function instead of initializing
those parameters by vendor driver itself.
Link: https://lore.kernel.org/r/20201116065054.7658-4-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Nowadays many vendors initialize their device parameters in their own
vendor drivers. The initialization code is almost the same as well as the
pre-defined definitions. Introduce a common device parameter initialization
function which assign the most common initial values. With this function,
we could remove those duplicated codes in vendor drivers.
Link: https://lore.kernel.org/r/20201116065054.7658-3-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Refactor performance scaling related functions in MediaTek UFS driver.
Link: https://lore.kernel.org/r/20201116065054.7658-2-stanley.chu@mediatek.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
QCOM_SCM is only needed to make the qcom_scm_*() calls in ufs-qcom-ice.c,
which is only compiled when SCSI_UFS_CRYPTO=y. So don't unnecessarily
enable QCOM_SCM when SCSI_UFS_CRYPTO=n.
Link: https://lore.kernel.org/r/20201114004754.235378-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Once HBA enabling has failed, add retry mechanism and allow vendors to
apply specific tweaks before the next retry. For example, vendors can do
vendor-specific host reset flow in variant function
"ufshcd_vops_hce_enable_notify()".
Link: https://lore.kernel.org/r/20201112054537.22494-1-stanley.chu@mediatek.com
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the missing destroy_workqueue() before return from ufshcd_init in the
error handling case as well as in ufshcd_remove.
Link: https://lore.kernel.org/r/20201110074223.41280-1-miaoqinglang@huawei.com
Fixes: 4db7a23605 ("scsi: ufs: Fix concurrency of error handler and other error recovery paths")
Suggested-by: Avri Altman <Avri.Altman@wdc.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Provide HS-G4 support in MediaTek UFS platforms.
To support HS-G4, introduce mechanism to get the MediaTek UFS controller
version. With such information, driver can make right decision to apply
different configurations in different controllers.
Link: https://lore.kernel.org/r/20201029115750.24391-7-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some vendors need newer UniPro version to decide if some features can be
enabled or not.
Simply add missing enums for the latest UniPro versions.
Link: https://lore.kernel.org/r/20201029115750.24391-6-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Support an option to allow users to disable auto-hibern8 feature.
Instead, enable hibern8-during-clk-gating feature to keep similar power
consumption.
Link: https://lore.kernel.org/r/20201029115750.24391-5-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS proprietary features (including features introduced later) in MediaTek
UFS platforms have complicated combinations among different platforms.
To ease code readability and maintenance, decouple all proprietary features
from platform bindings. Each feature would be enabled only if specific
property string is defined in device tree node.
Link: https://lore.kernel.org/r/20201029115750.24391-4-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some MediaTek UFS platforms need to control VA09 power
specifically. Provide such control according to the device tree binding.
Link: https://lore.kernel.org/r/20201029115750.24391-3-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In ufs_mtk_unipro_set_lpm(), use specific unsigned values as the argument
to invoke ufshcd_dme_set().
At the same time, change the name of ufs_mtk_unipro_set_pm() to
ufs_mtk_unipro_set_lpm() to align the naming convention in MediaTek UFS
driver.
Link: https://lore.kernel.org/r/20201029115750.24391-2-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes the following W=1 kernel build warning(s):
drivers/scsi/ufs/ufshcd.c:6603: warning: Function parameter or member 'hba' not described in 'ufshcd_try_to_abort_task'
drivers/scsi/ufs/ufshcd.c:6603: warning: Function parameter or member 'tag' not described in 'ufshcd_try_to_abort_task'
drivers/scsi/ufs/ufshcd.c:6603: warning: Excess function parameter 'cmd' description in 'ufshcd_try_to_abort_task'
Link: https://lore.kernel.org/r/20201102142359.561122-12-lee.jones@linaro.org
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: Santosh Yaraganavi <santosh.sy@samsung.com>
Cc: Vinayak Holikatti <h.vinayak@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the uic_cmd->cmd_active as a flag to track the lifecycle of an UIC cmd.
The flag is set before sending the UIC cmd and cleared in IRQ handler. When
a PMC or UIC cmd completion timeout happens, if the flag is not set,
instead of returning timeout error, we still treat it as a successful
operation. This is to deal with the scenario in which completion has been
raised but the one waiting for the completion cannot be awaken in time due
to kernel scheduling problem.
Link: https://lore.kernel.org/r/1604384682-15837-3-git-send-email-cang@codeaurora.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The scsi_block_reqs_cnt increased in ufshcd_hold() is supposed to be
decreased back in ufshcd_ungate_work() in a paired way. However, if
specific ufshcd_hold/release sequences are met, it is possible that
scsi_block_reqs_cnt is increased twice but only one ungate work is
queued. To make sure scsi_block_reqs_cnt is handled by ufshcd_hold() and
ufshcd_ungate_work() in a paired way, increase it only if queue_work()
returns true.
Link: https://lore.kernel.org/r/1604384682-15837-2-git-send-email-cang@codeaurora.org
Reviewed-by: Hongwu Su <hongwus@codeaurora.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is simpler for drivers to provide a ->device_reset() callback
irrespective of whether the GPIO, or firmware interface necessary to do the
reset, is discovered during probe.
Change ->device_reset() to return an error code. Drivers that provide the
callback, but do not do the reset operation should return -EOPNOTSUPP.
Link: https://lore.kernel.org/r/20201103141403.2142-3-adrian.hunter@intel.com
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bean huo <beanhuo@micron.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
DeepSleep is a UFS v3.1 feature that achieves the lowest power consumption
of the device, apart from power off.
In DeepSleep mode, no commands are accepted, and the only way to exit is
using a hardware reset or power cycle.
This patch assumes that if a power cycle was an option, then power off
would be preferable, so only exit via a hardware reset is supported.
Drivers that wish to support DeepSleep need to set a new capability flag
UFSHCD_CAP_DEEPSLEEP and provide a hardware reset via the existing
->device_reset() callback.
It is assumed that UFS devices with wspecversion >= 0x310 support
DeepSleep.
[mkp: dropped sysfs ABI doc due to conflicts]
Link: https://lore.kernel.org/r/20201103141403.2142-2-adrian.hunter@intel.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During clock gating, after clocks are disabled, put HBA into LPM to save
more power.
Link: https://lore.kernel.org/r/52198e70bff750632740d78678a815256d697e43.1603825776.git.asutoshd@codeaurora.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of the usual driver updates (ufs, qla2xxx, tcmu,
ibmvfc, lpfc, smartpqi, hisi_sas, qedi, qedf, mpt3sas) and minor bug
fixes. There are only three core changes: adding sense codes,
cleaning up noretry and adding an option for limitless retries.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCX4YulyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishaZDAQCT7rwG
UEZYHgYkU9EX9ERVBQM0SW4mLrxf3g3P5ioJsAEAtkclCM4QsIOP+MIPjIa0EyUY
khu0kcrmeFR2YwA8zhw=
=4w4S
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"The usual driver updates (ufs, qla2xxx, tcmu, ibmvfc, lpfc, smartpqi,
hisi_sas, qedi, qedf, mpt3sas) and minor bug fixes.
There are only three core changes: adding sense codes, cleaning up
noretry and adding an option for limitless retries"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (226 commits)
scsi: hisi_sas: Recover PHY state according to the status before reset
scsi: hisi_sas: Filter out new PHY up events during suspend
scsi: hisi_sas: Add device link between SCSI devices and hisi_hba
scsi: hisi_sas: Add check for methods _PS0 and _PR0
scsi: hisi_sas: Add controller runtime PM support for v3 hw
scsi: hisi_sas: Switch to new framework to support suspend and resume
scsi: hisi_sas: Use hisi_hba->cq_nvecs for calling calling synchronize_irq()
scsi: qedf: Remove redundant assignment to variable 'rc'
scsi: lpfc: Remove unneeded variable 'status' in lpfc_fcp_cpu_map_store()
scsi: snic: Convert to use DEFINE_SEQ_ATTRIBUTE macro
scsi: qla4xxx: Delete unneeded variable 'status' in qla4xxx_process_ddb_changed
scsi: sun_esp: Use module_platform_driver to simplify the code
scsi: sun3x_esp: Use module_platform_driver to simplify the code
scsi: sni_53c710: Use module_platform_driver to simplify the code
scsi: qlogicpti: Use module_platform_driver to simplify the code
scsi: mac_esp: Use module_platform_driver to simplify the code
scsi: jazz_esp: Use module_platform_driver to simplify the code
scsi: mvumi: Fix error return in mvumi_io_attach()
scsi: lpfc: Drop nodelist reference on error in lpfc_gen_req()
scsi: be2iscsi: Fix a theoretical leak in beiscsi_create_eqs()
...
For older versions of gcc, the array = {0}; will cause warnings:
drivers/scsi/ufs/ufshcd-crypto.c: In function 'ufshcd_crypto_keyslot_program':
drivers/scsi/ufs/ufshcd-crypto.c:62:8: warning: missing braces around initializer [-Wmissing-braces]
union ufs_crypto_cfg_entry cfg = { 0 };
^
drivers/scsi/ufs/ufshcd-crypto.c:62:8: warning: (near initialization for 'cfg.reg_val') [-Wmissing-braces]
drivers/scsi/ufs/ufshcd-crypto.c: In function 'ufshcd_clear_keyslot':
drivers/scsi/ufs/ufshcd-crypto.c:103:8: warning: missing braces around initializer [-Wmissing-braces]
union ufs_crypto_cfg_entry cfg = { 0 };
^
2 warnings generated
Link: https://lore.kernel.org/r/20201002063538.1250-1-shipujin.t@gmail.com
Fixes: 70297a8ac7 ("scsi: ufs: UFS crypto API")
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Pujin Shi <shipujin.t@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use devm_platform_ioremap_resource_byname() to simplify the code.
Link: https://lore.kernel.org/r/20200916084017.14086-1-huobean@gmail.com
Acked-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some MediaTek UFS platforms support high-performance mode that inline
encryption engine can be boosted while UFS is not clock-gated.
The high-performance mode will be enabled if all below conditions are
well-declaired in device tree,
- Proper platform-specific compatible string which enables the host
capability "UFS_MTK_CAP_BOOST_CRYPT_ENGINE".
- "dvfsrc-vcore" node is available in this platform.
- Required minimum vcore voltage for high-performance mode.
- Clock mux and clock parents of inline encryption engine for both
"low-power mode" and "high-performance mode".
Link: https://lore.kernel.org/r/20200914050052.3974-2-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Boot occasionally fails with some Samsung low-power UFS devices. The reason
is that these devices have a little bit higher latency for NOP OUT
responses. This causes boot to fail because the NOP OUT command is issued
during initialization to check whether the device transport protocol is
ready or not. Increase NOP_OUT_TIMEOUT value from 30 to 50ms.
Link: https://lore.kernel.org/r/231786897.01599016081767.JavaMail.epsvc@epcpadp2
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Daejun Park <daejun7.park@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Intel host controllers support the setting of latency tolerance.
Accordingly, implement the PM QoS ->set_latency_tolerance() callback. The
raw register values are also exposed via debugfs.
Link: https://lore.kernel.org/r/20200827072030.24655-1-adrian.hunter@intel.com
Fixes: 8c09d75276 ("scsi: ufshdc-pci: Add Intel PCI IDs for EHL")
Fixes: 1ab27c9cf8 ("ufs: Add support for clock gating")
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With !CONFIG_OF and SCSI_UFS_EXYNOS selected, the below warning is given:
WARNING: unmet direct dependencies detected for PHY_SAMSUNG_UFS
Depends on [n]: OF [=n] && (ARCH_EXYNOS || COMPILE_TEST [=y])
Selected by [y]:
- SCSI_UFS_EXYNOS [=y] && SCSI_LOWLEVEL [=y] && SCSI [=y] && SCSI_UFSHCD_PLATFORM [=y] && (ARCH_EXYNOS || COMPILE_TEST [=y])
Fix it by removing PHY_SAMSUNG_UFS dependency.
Link: https://lore.kernel.org/r/20200721172021.28922-1-alim.akhtar@samsung.com
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix build warnings with make W=1 as below,
1.
>> drivers/scsi/ufs/ufs-mediatek.c:116:22: warning: format '%d' expects
>> argument of type 'int', but argument 4 has type 'long int'
2.
CC [M] drivers/scsi/ufs/ufs-mediatek.o
../drivers/scsi/ufs/ufs-mediatek.c:749: error: Cannot parse struct or union!
/** is used specifically with kernel-doc tool.
As a quick fix by removing dubious /** in the comment block of
struct ufs_hba_variant_ops ufs_hba_mtk_vops.
Link: https://lore.kernel.org/r/20200910013756.11385-1-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Forcibly leave UniPro low-power mode if UIC commands failed. This makes
hba_enable_delay_us as correct (default) value for re-enabling the host.
At the same time, change type of parameter "lpm" in function
ufs_mtk_unipro_set_pm() to "bool".
Link: https://lore.kernel.org/r/20200908064507.30774-4-stanley.chu@mediatek.com
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Simply add HOST_PA_TACTIVATE quirk back since it was incorrectly removed
before.
Link: https://lore.kernel.org/r/20200908064507.30774-3-stanley.chu@mediatek.com
Fixes: 47d054580a ("scsi: ufs-mediatek: fix HOST_PA_TACTIVATE quirk for Samsung UFS Devices")
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some MediaTek platforms does not have to bind MPHY so users shall not see
any unnecessary logs. Simply remove logs for this case.
Link: https://lore.kernel.org/r/20200908064507.30774-2-stanley.chu@mediatek.com
Fixes: fc4983018f ("scsi: ufs-mediatek: Allow unbound mphy")
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Setting the Auto-Hibernate Timer to zero is a valid setting which indicates
the Auto-Hibernate feature being disabled. Correctly support this setting.
In addition, when the timer value is queried from sysfs, read from the host
controller's register and return that value instead of using the RAM value.
Link: https://lore.kernel.org/r/b141cfcd7998b8933635828b56fbb64f8ad4d175.1598661071.git.nguyenb@codeaurora.org
Acked-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Bao D. Nguyen <nguyenb@codeaurora.org>
Signed-off-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
PA Layer issues a LINERESET to the PHY at the recovery step in the Power
Mode change operation. If it happens during auto or manual hibern8 enter,
even if hibern8 enter succeeds, UFS power mode shall be set to PWM-G1 mode
and kept in that mode after exit from hibern8, leading to bad performance.
Handle the LINERESET in the eh_work by restoring power mode to HS mode
after all pending reqs and tasks are cleared from doorbell.
Link: https://lore.kernel.org/r/1598321228-21093-3-git-send-email-cang@codeaurora.org
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To recover non-fatal errors, no full reset is required, err_handler only
clears those pending TRs/TMRs so that SCSI layer can re-issue them. In
current err_handler, TRs are directly cleared from UFS host's doorbell but
not aborted from device side. However, according to the UFSHCI JEDEC spec,
the host software shall use UTP Transfer Request List Clear Register to
clear a task from UFS host's doorbell only when a UTP Transfer Request is
expected to not be completed, e.g. when the host software receives a
“FUNCTION COMPLETE” Task Management response which means a Transfer Request
was aborted. To follow the UFSHCI JEDEC spec, in err_handler, abort one TR
before clearing it from doorbell.
Link: https://lore.kernel.org/r/1598321228-21093-2-git-send-email-cang@codeaurora.org
Acked-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix ufshcd_print_trs() to consider UFSHCD_QUIRK_PRDT_BYTE_GRAN when using
utp_transfer_req_desc::prd_table_length, so that it doesn't treat the
number of bytes as the number of entries.
Originally from Kiwoong Kim
(https://lkml.kernel.org/r/20200218233115.8185-1-kwmad.kim@samsung.com).
Link: https://lore.kernel.org/r/20200826021040.152148-1-ebiggers@kernel.org
Fixes: 26f968d7de ("scsi: ufs: Introduce UFSHCD_QUIRK_PRDT_BYTE_GRAN quirk")
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We have two knobs to control flush for write booster,
fWriteBoosterBufferFlushDuringHibernate and fWriteBoosterBufferFlushEn.
Some vendors use only fWriteBoosterBufferFlushDuringHibernate because this
can reportedly cover most scenarios. Also, there have been some reports
that flush by fWriteBoosterBufferFlushEn could lead to increased power
consumption thanks to unexpected internal operations. Consequently, we need
a way to enable or disable fWriteBoosterEn operations. Add quirk to bypass
manual flush.
Link: https://lore.kernel.org/r/ffdb0eda30515809f0ad9ee936b26917ee9b4593.1598319701.git.kwmad.kim@samsung.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MediaTek UFS host now supports 2 lanes. Modify the lane count to 2.
This modification shall not impact old 1-lane host because
PA_CONNECTEDRXDATALANES and PA_CONNECTEDTXDATALANES will limit the target
lanes properly during power mode change. So we could relax the limitation
in ufs_dev_params.
Link: https://lore.kernel.org/r/20200819084340.7021-1-stanley.chu@mediatek.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Andy Teng <andy.teng@mediatek.com>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 5586dd8ea2 ("scsi: ufs: Fix a race condition between error handler
and runtime PM ops") moves the ufshcd_scsi_block_requests() inside
err_handler() but forgets to remove the ufshcd_scsi_unblock_requests() in
the early return path. Correct the mistake.
Link: https://lore.kernel.org/r/1597798958-24322-1-git-send-email-cang@codeaurora.org
Fixes: 5586dd8ea2 ("scsi: ufs: Fix a race condition between error handler and runtime PM ops")
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Reviewed-by: Hongwu Su<hongwus@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, the UFS driver busy waits for fDeviceInit to be cleared. Provide
an upper bound and sleep between attempts instead of busy waiting.
Link: https://lore.kernel.org/r/1597053747-75171-1-git-send-email-kwmad.kim@samsung.com
Tested-by: Kiwoong Kim <kwmad.kim@samsung.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20200814095034.20709-3-huobean@gmail.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ufshcd_comp_devman_upiu() was poorly named leading people to think it was a
completion function. Rename it to ufshcd_compose_devman_upiu().
Link: https://lore.kernel.org/r/20200814095034.20709-2-huobean@gmail.com
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
MSM bus scaling has moved on to use interconnect framework and downstream
bus scaling APIs like msm_bus_scale*() do not exist anymore in the
kernel. Currently they are guarded by a config which also does not exist
and hence there are no build failures reported. Remove these unused
interfaces as they are currently no-ops and the scaling support that may be
added in future will use interconnect API.
Link: https://lore.kernel.org/r/20200804161033.15586-1-saiprakash.ranjan@codeaurora.org
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In current UFS task abort hook, namely ufshcd_abort(), if one task is
aborted successfully, clk_gating.active_reqs held by this task is not
decreased, which makes clk_gating.active_reqs stay above zero forever, thus
clock gating would never happen. Instead of releasing resources of one task
"manually", use the existing func __ufshcd_transfer_req_compl(). This
change also eliminates a possible race of scsi_dma_unmap() from the real
completion in IRQ handler path.
Link: https://lore.kernel.org/r/1596975355-39813-10-git-send-email-cang@codeaurora.org
Fixes: 1ab27c9cf8 ("ufs: Add support for clock gating")
CC: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Asutosh Das <asutoshd@codeaurora.org>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kiwoong Kim