The DSI host links to the DSI PHY device using a custom binding. Switch to
the generic PHY bindings. The DSI PHY driver itself doesn't use the common
PHY framework for now.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DSI interface is going to have two ports defined in its device node.
The first port is always going to be the link between the MDP output
and the input to DSI, the second port is going to be the link between
the DSI output and the connected panel/bridge:
----- ----- -------
| MDP | ------> | DSI | ------> | Panel |
----- ----- -------
(Port 0) (Port 1)
Until now, there was only one Port representing the output. Update the
DSI host driver such that it parses Port #1 for a connected device.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Address some issues wiht clock related bindings. It's okay to change these
since these bindings aren't used in any dtsi files until now.
MDP5:
- Don't ask for source clock
MDP4:
- Give a better name for MDP_TV_CLK
- Remove TV_SRC
- Add MDP_AXI_CLK
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Fix some issues with MDP4 clocks:
- mdp4_dtv_encoder tries to get "src_clk", which is a RCG(TV_SRC) in
MSM8960 and APQ8064. This isn't something the driver should access or
configure. Instead of this, configure the "mdp_clk" (MDP_TV_CLK), a
branch clock in MMCC that has the TV_SRC as its parent. Setting
rate/enabling the "mdp_clk" will eventually configure "src_clk", which
is what we want.
- Rename "mdp_clk" to "tv_clk" because that's slightly less confusing.
- Rename "mdp_axi_clk" to "bus_clk" because that's what we do elsewhere
too.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The driver expects DT to provide the parent to MDP core clock. The only
operation done to the parent clock is to set a rate. This can be
achieved by setting the rate on the core clock itsef. Don't try to
get the parent clock anymore.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The msm_iommu_map/unmap funcs have debug prints to show the list of
VA:PA mappings. Use the correct variable to print the VAs.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The u32 type used to pass the physical addresses to iommu_map can't
accommodate 64 bit addresses. Move to dma_addr_t to ensure wrong
addresses aren't provided to the IOMMU driver.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
allowing GLSL shaders with non-unrolled loops.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Qh0U
-----END PGP SIGNATURE-----
Merge tag 'drm-vc4-next-2016-07-15' of https://github.com/anholt/linux into drm-next
This pull request brings in vc4 shader validation for branching,
allowing GLSL shaders with non-unrolled loops.
* tag 'drm-vc4-next-2016-07-15' of https://github.com/anholt/linux:
drm/vc4: Fix a "the the" typo in a comment.
drm/vc4: Fix definition of QPU_R_MS_REV_FLAGS
drm/vc4: Add a getparam to signal support for branches.
drm/vc4: Add support for branching in shader validation.
drm/vc4: Add a bitmap of branch targets during shader validation.
drm/vc4: Move validation's current/max ip into the validation struct.
drm/vc4: Add a getparam ioctl for getting the V3D identity regs.
This set of changes contains a few cleanups for existing panels as well
as improved handling of certain backlights. In addition there's support
for a few new simple panels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=XLd7
-----END PGP SIGNATURE-----
Merge tag 'drm/panel/for-4.8-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/panel: Changes for v4.8-rc1
This set of changes contains a few cleanups for existing panels as well
as improved handling of certain backlights. In addition there's support
for a few new simple panels.
* tag 'drm/panel/for-4.8-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/panel: simple: Add support for Starry KR122EA0SRA panel
dt-bindings: Add Starry KR122EA0SRA panel binding
dt-bindings: Add vendor prefix for Starry
dt-bindings: display: Add Sharp LQ101K1LY04 panel binding
drm/panel: simple: Add support for Sharp LQ101K1LY04
drm/panel: simple: Add support for LG LP079QX1-SP0V panel
dt-bindings: Add support for LG LP079QX1-SP0V panel
drm/panel: simple: Add support for Sharp LQ123P1JX31 panel
dt-bindings: Add Sharp LQ123P1JX31 panel binding
drm/panel: simple: Add support for Samsung LSN122DL01-C01 panel
dt-bindings: Add Samsung LSN122DL01-C01 panel binding
drm/panel: simple: Add support for LG LP097QX1-SPA1 panel
dt-bindings: Add LG LP097QX1-SPA1 panel binding
drm/panel: simple: Update backlight state property
drm/panel: simple: Remove gratuitous blank line
drm/panel: simple: Fix a couple of physical sizes
This set of changes contains a bunch of cleanups to the host1x driver as
well as the addition of a pin controller for DPAUX, which is required by
boards to configure the DPAUX pads in AUX mode (for DisplayPort) or I2C
mode (for HDMI and DDC).
Included is also a bit of rework of the SOR driver in preparation to add
DisplayPort support as well as some refactoring and cleanup.
Finally, all output drivers are converted to runtime PM, which greatly
simplifies the handling of clocks and resets.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=7xlG
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.8-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.8-rc1
This set of changes contains a bunch of cleanups to the host1x driver as
well as the addition of a pin controller for DPAUX, which is required by
boards to configure the DPAUX pads in AUX mode (for DisplayPort) or I2C
mode (for HDMI and DDC).
Included is also a bit of rework of the SOR driver in preparation to add
DisplayPort support as well as some refactoring and cleanup.
Finally, all output drivers are converted to runtime PM, which greatly
simplifies the handling of clocks and resets.
* tag 'drm/tegra/for-4.8-rc1' of git://anongit.freedesktop.org/tegra/linux: (35 commits)
drm/tegra: sor: Reject HDMI 2.0 modes
drm/tegra: sor: Prepare for generic PM domain support
drm/tegra: dsi: Prepare for generic PM domain support
drm/tegra: sor: Make XBAR configurable per SoC
drm/tegra: sor: Use sor1_src clock to set parent for HDMI
dt-bindings: display: tegra: Add source clock for SOR
drm/tegra: sor: Implement sor1_brick clock
drm/tegra: sor: Implement runtime PM
drm/tegra: hdmi: Implement runtime PM
drm/tegra: dsi: Implement runtime PM
drm/tegra: dc: Implement runtime PM
drm/tegra: hdmi: Enable audio over HDMI
drm/tegra: sor: Do not support deep color modes
drm/tegra: sor: Extract tegra_sor_mode_set()
drm/tegra: sor: Split out tegra_sor_apply_config()
drm/tegra: sor: Rename tegra_sor_calc_config()
drm/tegra: sor: Factor out tegra_sor_set_parent_clock()
drm/tegra: dpaux: Add pinctrl support
dt-bindings: Add bindings for Tegra DPAUX pinctrl driver
drm/tegra: Prepare DPAUX for supporting generic PM domains
...
Please consider merging this tag, which contains the v4 misc fixes and add RK3399 eDP support patches[0] I sent on 2016-06-29, rebased onto v4.7-rc5.
* 'upstream/analogix-dp-20160705' of git://github.com/yakir-Yang/linux:
dt-bindings: analogix_dp: rockchip: correct the wrong compatible name
drm/rockchip: analogix_dp: introduce the pclk for grf
drm/bridge: analogix_dp: fix no drm hpd event when panel plug in
drm/rockchip: analogix_dp: update the comments about why need to hardcode VOP output mode
drm/rockchip: analogix_dp: correct the connector display color format and bpc
drm/bridge: analogix_dp: passing the connector as an argument in .get_modes()
drm/rockchip: analogix_dp: make panel detect to an optional action
drm/rockchip: analogix_dp: add rk3399 eDP support
drm/bridge: analogix_dp: some rockchip chips need to flip REF_CLK bit setting
drm/bridge: analogix_dp: correct the register bit define error in ANALOGIX_DP_PLL_REG_1
drm/rockchip: analogix_dp: split the lcdc select setting into device data
- atomic mode setting conversion
- replace DMFC FIFO allocation mechanism with a fixed allocation
that is good enough for all cases
- support for external bridges connected to parallel-display
- improved error handling in imx-ldb, imx-tve, and parallel-display
- some code cleanup in imx-tve
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lWas
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-next-2016-07-14' of git://git.pengutronix.de/git/pza/linux into drm-next
imx-drm updates
- atomic mode setting conversion
- replace DMFC FIFO allocation mechanism with a fixed allocation
that is good enough for all cases
- support for external bridges connected to parallel-display
- improved error handling in imx-ldb, imx-tve, and parallel-display
- some code cleanup in imx-tve
* tag 'imx-drm-next-2016-07-14' of git://git.pengutronix.de/git/pza/linux:
drm/imx: parallel-display: add bridge support
drm/imx: parallel-display: check return code from of_get_drm_display_mode()
gpu: ipu-v3: ipu-dc: don't bug out on invalid bus_format
drm/imx: imx-tve: fix the error message
drm/imx: imx-tve: remove unneeded 'or' operation
drm/imx: imx-tve: check the value returned by regulator_set_voltage()
drm/imx: imx-ldb: check return code on panel attach
drm/imx: turn remaining container_of macros into inline functions
drm/imx: store internal bus configuration in crtc state
drm/imx: remove empty mode_set encoder callbacks
drm/imx: atomic phase 3 step 3: Advertise DRIVER_ATOMIC
drm/imx: atomic phase 3 step 2: Legacy callback fixups
drm/bridge: dw-hdmi: Remove the legacy drm_connector_funcs structure
drm/imx: atomic phase 3 step 1: Use atomic configuration
drm/imx: Remove encoders' ->prepare callbacks
drm/imx: atomic phase 2 step 2: Track plane_state->fb correctly in ->page_flip
drm/imx: atomic phase 2 step 1: Wire up state ->reset, ->duplicate and ->destroy
drm/imx: atomic phase 1: Use transitional atomic CRTC and plane helpers
gpu: ipu-v3: ipu-dmfc: Use static DMFC FIFO allocation mechanism
drm/imx: ipuv3 plane: Check different types of plane separately
We don't use it in shader validation currently, so it had no effect,
but best to fix it anyway in case we do some day.
Signed-off-by: Eric Anholt <eric@anholt.net>
Userspace needs to know if it can create shaders that do branching.
Otherwise, for backwards compatibility with old kernels it needs to
lower if statements to conditional assignments.
Signed-off-by: Eric Anholt <eric@anholt.net>
We're already checking that branch instructions are between the start
of the shader and the proper PROG_END sequence. The other thing we
need to make branching safe is to verify that the shader doesn't read
past the end of the uniforms stream.
To do that, we require that at any basic block reading uniforms have
the following instructions:
load_imm temp, <next offset within uniform stream>
add unif_addr, temp, unif
The instructions are generated by userspace, and the kernel verifies
that the load_imm is of the expected offset, and that the add adds it
to a uniform. We track which uniform in the stream that is, and at
draw call time fix up the uniform stream to have the address of the
start of the shader's uniforms at that location.
Signed-off-by: Eric Anholt <eric@anholt.net>
This isn't used yet, it's just a first step toward loop validation.
During the main parsing of instructions, we need to know when we hit a
new basic block so that we can reset validated state.
v2: Fix a stray semicolon after an if block. (caught by kbuild test).
Signed-off-by: Eric Anholt <eric@anholt.net>
This pull request adds to the rework patch series for IOMMU
integration to support ARM64bit architecture with DMA-IOMMU
glue code.
With this patch series, Exynos DRM works well on Exynos5433 SoC
with IOMMU enabled.
* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: iommu: add support for ARM64 specific code for IOMMU glue
drm/exynos: iommu: move ARM specific code to exynos_drm_iommu.h
drm/exynos: iommu: remove unused entries from exynos_drm_private strcuture
drm/exynos: iommu: add a check if all sub-devices have iommu controller
drm/exynos: iommu: move dma_params configuration code to separate functions
vblank timestamping, and a couple of small cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aF3C
-----END PGP SIGNATURE-----
Merge tag 'drm-vc4-next-2016-07-12' of https://github.com/anholt/linux into drm-next
This pull request brings in new vc4 plane formats for Android, precise
vblank timestamping, and a couple of small cleanups.
* tag 'drm-vc4-next-2016-07-12' of https://github.com/anholt/linux:
drm/vc4: remove redundant ret status check
drm/vc4: Implement precise vblank timestamping.
drm/vc4: Bind the HVS before we bind the individual CRTCs.
gpu: drm: vc4_hdmi: add missing of_node_put after calling of_parse_phandle
drm: vc4: enable XBGR8888 and ABGR8888 pixel formats
drm/vc4: clean up error exit path on failed dpi_connector allocation
- select igt testing depencies for CONFIG_DRM_I915_DEBUG (Chris)
- track outputs in crtc state and clean up all our ad-hoc connector/encoder
walking in modest code (Ville)
- demidlayer drm_device/drm_i915_private (Chris Wilson)
- thundering herd fix from Chris Wilson, with lots of help from Tvrtko Ursulin
- piles of assorted clean and fallout from the thundering herd fix
- documentation and more tuning for waitboosting (Chris)
- pooled EU support on bxt (Arun Siluvery)
- bxt support is no longer considered prelimary!
- ring/engine vfunc cleanup from Tvrtko
- introduce intel_wait_for_register helper (Chris)
- opregion updates (Jani Nukla)
- tuning and fixes for wait_for macros (Tvrkto&Imre)
- more kabylake pci ids (Rodrigo)
- pps cleanup and fixes for bxt (Imre)
- move sink crc support over to atomic state (Maarten)
- fix up async fbdev init ordering (Chris)
- fbc fixes from Paulo and Chris
* tag 'drm-intel-next-2016-07-11' of git://anongit.freedesktop.org/drm-intel: (223 commits)
drm/i915: Update DRIVER_DATE to 20160711
drm/i915: Select DRM_VGEM for igt
drm/i915: Select X86_MSR for igt
drm/i915: Fill unused GGTT with scratch pages for VT-d
drm/i915: Introduce Kabypoint PCH for Kabylake H/DT.
drm/i915:gen9: implement WaMediaPoolStateCmdInWABB
drm/i915: Check for invalid cloning earlier during modeset
drm/i915: Simplify hdmi_12bpc_possible()
drm/i915: Kill has_dsi_encoder
drm/i915: s/INTEL_OUTPUT_DISPLAYPORT/INTEL_OUTPUT_DP/
drm/i915: Replace some open coded intel_crtc_has_dp_encoder()s
drm/i915: Kill has_dp_encoder from pipe_config
drm/i915: Replace manual lvds and sdvo/hdmi counting with intel_crtc_has_type()
drm/i915: Unify intel_pipe_has_type() and intel_pipe_will_have_type()
drm/i915: Add output_types bitmask into the crtc state
drm/i915: Remove encoder type checks from MST suspend/resume
drm/i915: Don't mark eDP encoders as MST capable
drm/i915: avoid wait_for_atomic() in non-atomic host2guc_action()
drm/i915: Group the irq breadcrumb variables into the same cacheline
drm/i915: Wake up the bottom-half if we steal their interrupt
...
I recovered dri-devel backlog from my vacation, more misc stuff:
- of_put_node fixes from Peter Chen (not all yet)
- more patches from Gustavo to use kms-native drm_crtc_vblank_* funcs
- docs sphinxification from Lukas Wunner
- bunch of fixes all over from Dan Carpenter
- more follow up work from Chris register/unregister rework in various
places
- vgem dma-buf export (for writing testcases)
- small things all over from tons of different people
* tag 'topic/drm-misc-2016-07-14' of git://anongit.freedesktop.org/drm-intel: (52 commits)
drm: Don't overwrite user ioctl arg unless requested
dma-buf/sync_file: improve Kconfig description for Sync Files
MAINTAINERS: add entry for the Sync File Framework
drm: Resurrect atomic rmfb code
drm/vgem: Use PAGE_KERNEL in place of x86-specific PAGE_KERNEL_IO
qxl: silence uninitialized variable warning
qxl: check for kmap failures
vga_switcheroo: Sphinxify docs
drm: Restore double clflush on the last partial cacheline
gpu: drm: rockchip_drm_drv: add missing of_node_put after calling of_parse_phandle
gpu: drm: sti_vtg: add missing of_node_put after calling of_parse_phandle
gpu: drm: sti_hqvdp: add missing of_node_put after calling of_parse_phandle
gpu: drm: sti_vdo: add missing of_node_put after calling of_parse_phandle
gpu: drm: sti_compositor: add missing of_node_put after calling of_parse_phandle
drm/tilcdc: use drm_crtc_handle_vblank()
drm/rcar-du: use drm_crtc_handle_vblank()
drm/nouveau: use drm_crtc_handle_vblank()
drm/atmel: use drm_crtc_handle_vblank()
drm/armada: use drm_crtc_handle_vblank()
drm: make drm_vblank_count_and_time() static
...
Reduces the argument count for some of the functions, and will be used
more with the upcoming looping support.
Signed-off-by: Eric Anholt <eric@anholt.net>
As I extend the driver to support different V3D revisions, userspace
needs to know what version it's targeting. This is most easily
detected using the V3D identity registers.
v2: Make sure V3D is runtime PM on when reading the registers.
v3: Switch to a 64-bit param value (suggested by Rob Clark in review)
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v2)
Reviewed-by: Rob Clark <robdclark@gmail.com> (v3, over irc)
Enabling HDMI 2.0 modes requires extra programming and will not work
with the current driver, so reject all those modes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR driver for Tegra requires the SOR power partition to be enabled.
Now that Tegra supports the generic PM domain framework we manage the
SOR power partition via this framework. However, the sequence for
gating/ungating the SOR power partition requires that the SOR reset is
asserted/de-asserted at the time the SOR power partition is
gated/ungated, respectively. Now that the reset control core assumes
that resets are exclusive, the Tegra generic PM domain code and the SOR
driver cannot request the same reset unless we mark the reset as shared.
Sharing resets will not work in this case because we cannot guarantee
that the reset will be asserted/de-asserted at the appropriate time.
Therefore, given that the Tegra generic PM domain code will handle the
resets, do not request the reset in the SOR driver if the SOR device has
a PM domain associated.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI driver for Tegra requires the SOR power partition to be enabled.
Now that Tegra supports the generic PM domain framework we manage the
SOR power partition via this framework. However, the sequence for
gating/ungating the SOR power partition requires that the DSI reset is
asserted/de-asserted at the time the SOR power partition is
gated/ungated, respectively. Now that the reset control core assumes
that resets are exclusive, the Tegra generic PM domain code and the DSI
driver cannot request the same reset unless we mark the reset as shared.
Sharing resets will not work in this case because we cannot guarantee
that the reset will be asserted/de-asserted at the appropriate time.
Therefore, given that the Tegra generic PM domain code will handle the
resets, do not request the reset in the DSI driver if the DSI device has
a PM domain associated.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When running in HDMI mode, the sor1 IP block needs to use the sor1_src
as parent clock, and in turn configure the sor1_src to use pll_d2_out0
as its parent.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR clock can have various sources, with the most commonly used
being the sor_safe, pll_d2_out0, pll_dp and sor_brick clocks. These
are configured using a three level mux, of which the first 2 levels
can be treated as one. The direct parents of the SOR clock are the
sor_safe, sor_brick and sor_src clocks, whereas the pll_d2_out0 and
pll_dp clocks can be selected as parents of the sor_src clock via a
second mux.
Previous generations of Tegra have only supported eDP and LVDS with
the SOR, where LVDS was never used on publicly available hardware.
Clocking for this only ever required the first level mux (to select
between sor_safe and sor_brick).
Tegra210 has a new revision of the SOR that supports HDMI and hence
needs to support the second level mux to allow selecting pll_d2_out0
as the SOR clock's parent. This second mux is knows as sor_src, and
operating system software needs a reference to it in order to select
the proper parent.
Signed-off-by: Thierry Reding <treding@nvidia.com>
sor1_brick is a clock that can be used as a source for the sor1 clock.
The registers to control the clock output are part of the sor1 IP block
and hence the sor driver is the best place to implement it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently, we completely ignore the user when it comes to the in/out
direction of the ioctl argument, as we simply cannot trust userspace.
(For example, they might request a copy of the modified ioctl argument
when the driver is not expecting such and so leak kernel stack.)
However, blindly copying over the target address may also lead to a
spurious EFAULT, and a failure after the ioctl was completed
successfully. This is important in order to avoid an ABI break when
extending an ioctl from IOR to IORW. Similar to how we only copy the
intersection of the kernel arg size and the user arg size, we only want
to copy back the kernel arg data iff both the kernel and userspace
request the copy.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1468335590-21023-1-git-send-email-chris@chris-wilson.co.uk
Here's an initial drm-next pull for nouveau 4.8, highlights:
- GK20A/GM20B volt and clock improvements.
- Initial support for GP100/GP104 GPUs, GP104 will not yet support
acceleration due to NVIDIA having not released firmware for them as of yet.
* 'linux-4.8' of git://github.com/skeggsb/linux: (97 commits)
drm/nouveau/bus: remove cpu_coherent flag
drm/nouveau/ttm: remove special handling of coherent objects
drm/nouveau: check for supported chipset before booting fbdev off the hw
drm/nouveau/ce/gp104: initial support
drm/nouveau/fifo/gp104: initial support
drm/nouveau/disp/gp104: initial support
drm/nouveau/dma/gp104: initial support
drm/nouveau/ltc/gp104: initial support
drm/nouveau/ibus/gp104: initial support
drm/nouveau/i2c/gp104: initial support
drm/nouveau/gpio/gp104: initial support
drm/nouveau/fuse/gp104: initial support
drm/nouveau/bus/gp104: initial support
drm/nouveau/bar/gp104: initial support
drm/nouveau/mmu/gp104: initial support
drm/nouveau/fb/gp104: initial support
drm/nouveau/imem/gp104: initial support
drm/nouveau/devinit/gp104: initial support
drm/nouveau/bios/gp104: initial support
drm/nouveau/tmr/gp104: initial support
...
This flag's only remaining function is to ignore the uncached flag for
BOs on coherent architectures.
However the reason for allocating an object uncache on a non-coherent
architecture (namely because the cost of doing explicit flushes/
invalidations is higher than the benefit of caching the data because
accesses are few and far between) should also apply on architectures for
which coherency is maintained implicitly. Thus allocate coherent objects
as uncached on all architectures.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
TTM-allocated coherent objects were populated using the DMA API and
accessed using the mapping it returned to workaround coherency
issues. These issues seem to have been solved, thus remove this extra
case to handle and use the regular kernel mapping functions.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Archit Taneja