The current code in pcm_lib.c do all checks using only the position
in the ring buffer. Unfortunately, where the interrupts gets delayed or
merged into one, we need another timing source to check when the
buffer size boundary overlaps to avoid the wrong updating of the
ring buffer pointers.
This code uses jiffies to check the right time window without any
performance impact.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (214 commits)
ALSA: hda - Add pin-fix for HP dc5750
ALSA: als4000: Fix potentially invalid DMA mode setup
ALSA: als4000: enable burst mode
ALSA: hda - Fix initial capsrc selection in patch_alc269()
ASoC: TWL4030: Capture route runtime DAPM ordering fix
ALSA: hda - Add PC-beep whitelist for an Intel board
ALSA: hda - More relax for pending period handling
ALSA: hda - Define AC_FMT_* constants
ALSA: hda - Fix beep frequency on IDT 92HD73xx and 92HD71Bxx codecs
ALSA: hda - Add support for HDMI HBR passthrough
ALSA: hda - Set Stream Type in Stream Format according to AES0
ALSA: hda - Fix Thinkpad X300 so SPDIF is not exposed
ALSA: hda - FIX to not expose SPDIF on Thinkpad X301, since it does not have the ability to use SPDIF
ASoC: wm9081: fix resource reclaim in wm9081_register error path
ASoC: wm8978: fix a memory leak if a wm8978_register fail
ASoC: wm8974: fix a memory leak if another WM8974 is registered
ASoC: wm8961: fix resource reclaim in wm8961_register error path
ASoC: wm8955: fix resource reclaim in wm8955_register error path
ASoC: wm8940: fix a memory leak if wm8940_register return error
ASoC: wm8904: fix resource reclaim in wm8904_register error path
...
All current users of pm_qos_add_request() have the ability to supply
the memory required by the pm_qos routines, so make them do this and
eliminate the kmalloc() with pm_qos_add_request(). This has the
double benefit of making the call never fail and allowing it to be
called from atomic context.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: mark gross <markgross@thegnar.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
When using poll() to wait for the next period -- or avail_min samples --
one gets a consistent delay for each system call that is usually just a
little short of the selected period time. However, When using
snd_pcm_read/write(), one gets a jittery delay that alternates between
less than a millisecond and approximately two period times. This is
caused by snd_pcm_lib_{read,write}1() transferring any available samples
to the user's buffer and adjusting the application pointer prior to
sleeping to the end of the current period. When the next period
interrupt occurs, there is then less than avail_min samples remaining to
be transferred in the period, so we end up sleeping until a second
period occurs.
This is solved by using runtime->twake as the number of samples needed
for a wakeup in addition to selecting the proper wait queue to wake in
snd_pcm_update_state(). This requires twake to be non-zero when used
by snd_pcm_lib_{read,write}1() even if avail_min is zero.
Signed-off-by: Dave Dillow <dave@thedillows.org>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This defines the 24bps and 40bps (8khz sample rate) G.723 codec
formats. They are going to be used once I submit the driver for
an mpeg4/g723 compression card.
I've updated the signed value to -1 as per Takashi's comments
since these are non-linear formats.
Signed-off-by: Ben Collins <bcollins@bluecherry.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes the string based list management to a handle base
implementation to help with the hot path use of pm-qos, it also renames
much of the API to use "request" as opposed to "requirement" that was
used in the initial implementation. I did this because request more
accurately represents what it actually does.
Also, I added a string based ABI for users wanting to use a string
interface. So if the user writes 0xDDDDDDDD formatted hex it will be
accepted by the interface. (someone asked me for it and I don't think
it hurts anything.)
This patch updates some documentation input I got from Randy.
Signed-off-by: markgross <mgross@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Clemens Ladisch noted for hw_ptr_removal in "cleanup & merge hw_ptr
update functions" commit:
"It is possible for the status/delay ioctls to be called when the sound
card's pointer register alreay shows a position at the beginning of the
new period, but immediately before the interrupt is actually executed.
(This happens regularly on a SMP machine with mplayer.) When that
happens, the code thinks that the position must be at least one period
ahead of the current position and drops an entire buffer of data."
Return back the hw_ptr_interrupt variable. The last interrupt pointer
is always computed from the latest hw_ptr instead of tracking it
separately (in this case all hw_ptr checks and modifications might
influence also hw_ptr_interrupt and it is difficult to keep it
consistent).
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This change fixes the "ALSA: pcm_lib - optimize wake_up() calls for PCM I/O"
commit. New sleeping queue is introduced to separate user space and kernel
space wake_ups. runtime->nowake is renamed to twake (transfer wake).
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
pgprot_noncached() can be set for vmalloc'ed buffers safely, and we'd
need non-cached behavior more or less, even for the intermediate ring-
buffers.
Now snd_pcm_lib_mmap_vmalloc() is added as the common PCM mmap callback
that is coupled with snd_pcm_lib_alloc_vmalloc_buffer() & co.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As noted by pl bossart <bossart.nospam@gmail.com>, the PCM I/O routines
(snd_pcm_lib_write1, snd_pcm_lib_read1) should block wake_up() calls
until all samples are not processed.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Do general cleanup in snd_pcm_update_hw_ptr*() routines and merge them.
The main change is hw_ptr_interrupt variable removal to simplify code
logic. This variable can be computed directly from hw_ptr.
Ensure that updated hw_ptr is not lower than previous one (it was possible
with old code in some obscure situations when interrupt was delayed or
the lowlevel driver returns wrong ring buffer position value).
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
In some debug cases, it might be usefull to see previous ring buffer
positions to determine position problems from the lowlevel drivers.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
There are now five copies of the code to allocate a PCM buffer using
vmalloc(). Add a sixth in the core so that the others can be removed.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Record the pid of the task that opened a PCM substream. For sound
cards with hardware mixing, this allows determining which process
is associated with a specific substream's volume control.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Re-export snd_pcm_format_name() function to be used outside the PCM core.
As a first example, usbaudio is changed to use it now again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Using SG-buffers with dma_alloc_coherent() is often very inefficient
on non-coherent architectures because a tracking record could be
allocated in addition for each dma_alloc_coherent() call.
Instead, simply disable SG-buffers but just allocate normal continuous
buffers on non-supported (currently all but x86) architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* topic/pcm-jiffies-check:
ALSA: pcm - A helper function to compose PCM stream name for debug prints
ALSA: pcm - Fix update of runtime->hw_ptr_interrupt
ALSA: pcm - Fix a typo in hw_ptr update check
ALSA: PCM midlevel: lower jiffies check margin using runtime->delay value
ALSA: PCM midlevel: Do not update hw_ptr_jiffies when hw_ptr is not changed
ALSA: PCM midlevel: introduce mask for xrun_debug() macro
ALSA: PCM midlevel: improve fifo_size handling
Move the fifo_size assignment to hw->ioctl callback to allow lowlevel
drivers overwrite the default behaviour.
fifo_size is in frames not bytes as specified in asound.h and alsa-lib's
documentation, but most hardware have fixed byte based FIFOs. Introduce
internal SNDRV_PCM_INFO_FIFO_IN_FRAMES.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added runtime->delay field to adjust the delayed samples for snd_pcm_delay().
Typically a hardware FIFO length is stored in this field, so that the
extra delay between hwptr and applptr can be computed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some drivers like Intel8x0 or Intel HDA are broken for some hardware variants.
This patch adds more strict buffer position checks based on jiffies when
internal hw_ptr is updated. Enable xrun_debug to see mangling of wrong
positions.
As a side effect, the hw_ptr interrupt update routine might do slightly better
job when many interrupts are lost.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The timer callbacks are called in the protected status by the lock
of the timer instance, so there is no need for an extra lock in the
PCM substream.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Impact: cleanup
snd_pcm_new takes a char *id argument, although it is not modifying
the string. it can therefore be declared as const char *id.
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Most hardwares have limited buffer-descriptor table length. This
also restricts the max buffer size of the sound driver.
For example, snd-hda-intel has 1MB buffer size limit, and this is
because it can have at most 256 BDL entries. For supporting larger
buffers, we need to allocate larger pages even for sg-buffers.
This patch changes the sgbuf allocation code to try to allocate
larger pages first. At each head of the allocated pages, the
number of allocated pages is stored in the lowest bits of the
corresponding entry of the table addr field. This change isn't
visible as long as the driver uses snd_sgbuf_get_addr() helper.
Also, the patch adds a new function, snd_pcm_sgbuf_get_chunk_size().
This returns the size of the chunk on continuous pages starting at
the given position offset. If the chunk reaches to a non-continuous
page, it returns the size to the boundary.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Clean up SG-buffer helper functions and macros. Helpers take substream
as arguments now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Kill snd_assert() in sound/core/*, either removed or replaced with
if () with snd_BUG_ON().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
When compiled with CONFIG_SND_DYNAMIC_MINORS the ALSA core is fine
to have more than 8 PCM devices per card, except one place - the
SNDRV_CTL_IOCTL_PCM_NEXT_DEVICE ioctl, which will not enumerate
devices > 7. This patch fixes the issue, changing the devices list
organisation.
Instead of adding new device to the tail, the list is now kept always
ordered (by card number, then device number). Thus, during enumeration,
it is easy to discover the fact that there is no more given card's
devices.
Additionally the device field of struct snd_pcm had to be changed to int,
as its "unsignednity" caused a lot of problems when comparing it to
potentially negative signed values. (-1 is 0xffffffff or even more then ;-)
Signed-off-by: Pawel Moll <pawel.moll@st.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This reverts commit fb3d6f2b77bdec75d45aa9d4464287ed87927866.
New, updated patch with same subject replaces this commit.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
When compiled with CONFIG_SND_DYNAMIC_MINORS the ALSA core is fine
to have more than 8 PCM devices per card, except one place - the
SNDRV_CTL_IOCTL_PCM_NEXT_DEVICE ioctl, which will not enumerate
devices > 7. This patch fixes the issue, changing the devices list
organisation.
Instead of adding new device to the tail, the list is now kept always
ordered (by card number, then device number). Thus, during enumeration,
it is easy to discover the fact that there is no more given card's
devices. The same limit was present in OSS emulation code. It has
been fixed as well.
Additionally the device field of struct snd_pcm is now int, instead of
unsigned int, as there is no obvious reason for keeping it unsigned.
This caused a lot of problems with comparing this value with other
(almost always signed) variables. There is just one more place where
device number is unsigned - in struct snd_pcm_info, which should be
also sorted out in future.
Signed-off-by: Pawel MOLL <pawel.moll@st.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The 'tick' in PCM is set (again) via sw_params. And, nobody uses
this feature at all except for a command line option of aplay.
(This is literally 'nobody', as I checked alsa-lib API calls in all
programs in major distros.)
Above all, if we need finer wake-ups for the position update, it's
basically an issue that the driver should solve, not tuned by each
application.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The xfer_align sw_params parameter has never been used in a sane manner,
and no one understands what this does exactly. The current
implementation looks also buggy because it allows write of shorter size
than xfer_align. So, if you do partial writes, the write isn't actually
aligned at all.
Removing this parameter will make some pcm_lib_* code more readable
(and less buggy).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
We need an accurate and continuous (monotonic) time sources to do
accurate synchronization among more timing sources. This patch allows
to enable monotonic timestamps for ALSA PCM devices and enables monotonic
timestamps for ALSA timer devices.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The volatile prefix is just useless there. Let's kill them, and then
gcc will be happier, too.
sound/acore/pcm.c:867: warning: passing argument 1 of ‘__constant_c_and_count_memset’ discards qualifiers from pointer target type
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fixed cast messes in pcm.h.
include/sound/pcm.h: In function ‘hw_param_interval_c’:
include/sound/pcm.h:800: warning: passing argument 1 of ‘hw_param_interval’ discards qualifiers from pointer target type
Simply redefine the inline functions again for const pointers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Add a snd_pcm_rate_to_rate_bit() function to factor out common code used
by several drivers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Merge the rates[] arrays from pcm_misc.c and pcm_native.c because they
are both the same.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added a new macro snd_pcm_group_for_each_entry() just for code cleanup.
Old macros, snd_pcm_group_for_each() and snd_pcm_group_substream_entry(),
are removed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a struct device pointer to struct snd_pcm in order to be
able to give it a different device than the card. It defaults to the card's
device, however, so it should behave identically for drivers not touching
the field.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Jaroslav Kysela