In commit 9c204b46c7
(ath9k_hw: do not limit initial tx power to 20 dbm),
setting of txpower was broken.
This patch fixes it by initializing reg_pwr from the new
power limit, not the previous value.
Signed-off-by: Bill Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rx latecy to start signal(usec) of 11a is 41 not 37 and
also corrected the rx delay in quarter rate.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k_hw: Fix exceed transmission burst-time of 5GHz" added
a padding of 60 delimiters on the first subframe to work around an issue
on AR9380, but it lacked the checks to prevent it from being applied to
pre-AR9380, enterprise AR9380 or AR9580+
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous register used in these initvals was probably accidentally
copied over from the AR9100 values.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was used for the defunct 'turbo' mode which was never implemented in the
driver. Saves ~7.5k uncompressed
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is only used to workaround interoperability issues related to longer
delays in receiving the block ack, so it is not necessary to apply it
to the CTS exchange.
Should improve throughput slightly, especially when there are lots
of retransmissions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With sequence number and buffer allocation deferred to when they're needed
for the first time, it becomes much easier to start dropping packets from
the tid queue if necessary, e.g. when latency suddenly increases. This can
lead to some future improvements in buffer management for better latency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is only necessary for BAW tracking and moving it to the ath_buf
makes it easier to add further improvements, such as deferring
seqno allocation in the aggregation path.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a sk_buff_head instead containing skbs instead of a list_head
containing ath_bufs. This makes it easier to decouple the aggregation
code from the ath_buf struct
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changing the return type and removing the unused argument from
ath_printk reduces code size.
Add an __always_unused struct ath_common * to the macros
that call ath_printk to avoid unused variable warnings.
$ size drivers/net/wireless/ath/built-in.o*
text data bss dec hex filename
1159859 16235 212000 1388094 152e3e drivers/net/wireless/ath/built-in.o.new
1164175 16235 212032 1392442 153f3a drivers/net/wireless/ath/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return value is never used so make it void.
Reduces object size a tiny bit.
$ size drivers/net/wireless/ath/built-in.o*
text data bss dec hex filename
1164175 16235 212032 1392442 153f3a drivers/net/wireless/ath/built-in.o.new
1164819 16235 212032 1393086 1541be drivers/net/wireless/ath/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch keep track of number of samples that includes
DMA debugs registers, PCU observe, CR, channel noise,
cycle conters, noisefloor history buffer and last N number
of tx and rx descriptor status. These samples are grouped
in table manner which dumping in debgufs.
Debugfs file location:
<debugfs_mnt>/ieee80211/phy#/ath9k/samples
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent commit "ath9k: Send legacy rated frames as unaggregated"
introduced a check to ensure that packets with non-MCS rates set in
the rate series will not be aggregated. However, it failed to check
if the rate series is valid before testing the flags, thus breaking
aggregation for normal MCS-only packets if the last series is unset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For AR9287 v1.3+ chips, MAC runs at 117MHz. But the initvals
IFS parameters are loaded based on 44/88MHz clockrate. So
eifs/usec from ini should not be used for AR9287 v1.3+.
The mentioned values are tested on 2 chain HT40 mode.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize 9us slot time as that is what is used mostly
(for non-ERP cases) and also to be in sync with initvals.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
removed a function declaration, removed a variable, renamed a variable
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
in the Rx path of the driver it would be better to use ATH_DBG_ANY
rather than ATH_DBG_XMIT for printing debug messages
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9340 is not listed in ath_mac_bb_names, which leads to such a message:
ieee80211 phy0: Atheros AR???? Rev:0 mem=0xb8100000, irq=2
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has been tested in STA and AP mode by Florian.
Cc: David Quan <dquan@qca.qualcomm.com>
Cc: Kathy Giori <kgiori@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the do_div macro for 64-bit division. Otherwise, the module will
reference __udivdi3 under 32-bit kernels, which is not allowed in
kernel space.
drivers/built-in.o: In function `carl9170_collect_tally':
cmd.c:191: undefined reference to `__udivdi3'
cmd.c:192: undefined reference to `__udivdi3'
cmd.c:193: undefined reference to `__udivdi3'
Reported-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Tested-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Here are the AR9580 1.0 initvals checksums using the
Atheros initvals-tools [1]. This is useful for when
we udate the initvals again with other values. It ensures
that we match the same initvals used internally. The
tool is documented on the wiki [2].
$ ./initvals -f ar9580-1p0
0x00000000e912711f ar9580_1p0_modes_fast_clock
0x000000004a488fc7 ar9580_1p0_radio_postamble
0x00000000f3888b02 ar9580_1p0_baseband_core
0x0000000003f783bb ar9580_1p0_mac_postamble
0x0000000094be244a ar9580_1p0_low_ob_db_tx_gain_table
0x0000000094be244a ar9580_1p0_high_power_tx_gain_table
0x0000000090be244a ar9580_1p0_lowest_ob_db_tx_gain_table
0x00000000ed9eaac6 ar9580_1p0_baseband_core_txfir_coeff_japan_2484
0x00000000c4d66d1b ar9580_1p0_mac_core
0x00000000e8e9043a ar9580_1p0_mixed_ob_db_tx_gain_table
0x000000003521a300 ar9580_1p0_wo_xlna_rx_gain_table
0x00000000301fc841 ar9580_1p0_soc_postamble
0x00000000a9a06b3a ar9580_1p0_high_ob_db_tx_gain_table
0x00000000a15ccf1b ar9580_1p0_soc_preamble
0x0000000029495000 ar9580_1p0_rx_gain_table
0x0000000037ac0ee8 ar9580_1p0_radio_core
0x00000000603a1b80 ar9580_1p0_baseband_postamble
0x000000003d8b4396 ar9580_1p0_pcie_phy_clkreq_enable_L1
0x00000000398b4396 ar9580_1p0_pcie_phy_clkreq_disable_L1
0x00000000397b4396 ar9580_1p0_pcie_phy_pll_on_clkreq
[1] git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/initvals-tool.git
[2] http://wireless.kernel.org/en/users/Drivers/ath9k_hw/initvals-tool
Cc: David Quan <dquan@qca.qualcomm.com>
Cc: Kathy Giori <kgiori@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
currently this call back is used only in debugfs of mac80211
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the aggregation is formed till the aggregation limit
is reached and the rate lookup is done for the first frame alone.
But there can be a legacy rated frames in tid queue. This patch
limits the subframe addition based on presence of legacy rate and
sends the legacy rated frames as unaggregated one.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Walsh bit is disabled for regulatory consideration.
FCC limit for walsh enable is lower than that for walsh disable. So
disabling walsh bit will not limit tx power/affect tx power even in
cases where we are not FCC limited (most client cards). If the tx
power is not FCC limited, then enabling/disabling walsh bit will
not affect Avg. EVM/overall performance in any visible manner.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In congested network, having all rate reties at MCS rates
is failing to transmit the frame offenly. By the time reaching
the success rate set, the application gets timed out. One such
scenario is that authentication time out during 4-Way handshake.
This patch uses a legacy rate as last retry sequnce for
unaggregated frames or if the first selected rate's PER is ~80%
of max limit. And also observed from the tx status that the frame
was trasmitted successfully by using legacy rates.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this useful for debugging and to keep track of success/failure of
frames such as ACK, RTS and FCS error count in a noisy environment
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevent 8 bytes from being truncated from MGMT packets
when using TKIP.
Signed-off-by: Bill Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EIFS value read from AR_D_GBL_IFS_EIFS register in core clocks and then
written back as microsecond value.
Signed-off-by: Alex Hacker <hacker@epn.ru>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All AR9170 hardware have a 16-Bit random number generator.
The documentation claims the values are suitable for
"security keys".
The "throughput" is around 320Kibit/s. It's slow, but it
does work without introducing any special offload
firmware commands.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware keeps track of channel usage. This data can
be used by the automatic channel selection to find the
*best* channel.
Survey data from wlan22
frequency: 2412 MHz [in use]
noise: -86 dBm
channel active time: 3339608 ms
channel busy time: 270982 ms
channel transmit time: 121515 ms
Survey data from wlan22
frequency: 2417 MHz
noise: -86 dBm
channel active time: 70 ms
channel busy time: 2 ms
channel transmit time: 1 ms
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Import new headers from our firmware branch:
git://git.kernel.org/pub/scm/linux/kernel/git/chr/carl9170fw.git
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9170_PWR_REG_PLL_ADDAC is used to set the main clock
divisor which affects the AHB/CPU speed. Because this
would interfere with the firmware internal timekeeping,
the function has to be moved into the firmware.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On embedded hardware it's normal to not have a PCI device for the PCI
bridge that the wifi card is attached to. pdev->bus->self will be
NULL in that case. In that case, simply return without emitting an
useless kernel stack trace.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While switching b/w HT20/40, the current channel's nf values
are updated into history buffer. Since the current channel's
channel type, channel flag got updated before reading
nf value from hw. This channel type mismatch is causing invalid
readings when hw is on ht20 but getnf tries to read on extn chains.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before doing hw reset the current channel's noisefloor readings
are updated into history buffer. The extension chain's readings
are considered only if the current channel was configured in HT40.
While moving from HT40 to HT20, the extn chain's readings are
skipped though the current channel is in ht40. This patch updates
extn chain reading based on channel flag.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chainmasks were already configured at process_ini
before doing init calibration.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Once RXEOL was disabled, it never be enabled again. This patch
re-enables rxeol at the end of rx tasklet.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever RXEOL is received, both RXORN and RXEOL got cleared
to avoid rx overrun interrupt storm. This was handled only for
edma chips. The same scenario was also observered with AR9280,
doing frequent channel type switch b/w HT20/40 with bidi traffic
that is causing failure to stop rx dma. This patch clears
the RXEOL & RXORN interrupts for all chips.
ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020
DMADBG_7=0x000062c0
ath: Could not stop RX, we could be confusing the DMA engine when we
start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:532
ath_stoprecv+0x110/0x120 [ath9k]()
Call Trace:
[<ffffffff8104a55a>] warn_slowpath_common+0x7a/0xb0
[<ffffffff8104a5a5>] warn_slowpath_null+0x15/0x20
[<ffffffffa0560380>] ath_stoprecv+0x110/0x120 [ath9k]
[<ffffffffa055e6fa>] ath_reset+0x6a/0x200 [ath9k]
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The WAR which adds extra delimiters when using RTS/CTS
with aggregation and non-enterprise AR9003 chips.
This extra padding is done after doing all the 4ms limit
checks and hence the total aggregate sizes are exceeding
the allowed duration. This patch limits the aggregate
sizes appropriately after including these extra delimiters.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable ASPM in pci ->probe on upstream (device) and downstream
(PCIe port) component. According to e1000e driver authors this is
required. I did not find that requirement in PCIe spec, but it seems
to be logical for me.
This need to be fixed for CONFIG_PCIEASPM, that will be done later ...
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bill Jordan