The original driver for Silvercrest cameras were using some values that
are different from what datasheet says. As result, it was taken very
less snapshots per second than expected.
A test with the datasheet values showed that they work fine and give a
better frame rate. So, let's stick with datasheet values.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of working with a table of precalculated values, fill them with
the proper values. Also, adds format functions that allow changing the
resolution, by cropping the image to the center of the sensor.
While here, move the sensor version check to the probe routine, to
indicate to the caller if the sensor is not supported by this driver.
Also, fixes a stupid bug where we're using &buffer[] instead of
buffer[].
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds driver for mt9v011 based on its datasheet, available at:
http://download.micron.com/pdf/datasheets/imaging/MT9V011.pdf
The driver was tested with a webcam that will be added on a next patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
add FIXME comment to indicate that the set_frontend override is a
temporary hack. This will be done a better way in the next kernel.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use separate RF input spigots for Antennae and Cable.
Reviewed-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add DVB-T support for Yuan MPC-718 cards with an MT352 or ZL10353 demodulator.
There are apparently some units with a DiBcom demodulator which could be
supported by one of the dib7000 modules - but this is not implemented in the
cx18 driver (yet).
Due to lack of porgramming details for the MT352 and the mt352 module requiring
a "demod_init" function, a "firmware" must be obtained and loaded to get
DVB-T working for Yuan MPC-718 cards with an MT352.
Tested-by: Steve Firth <firth650@btinternet.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add routine to support extracting the MT352 DVB-T demodulator initialization
sequence for Yuan MPC718 cards for use by the cx18 driver.
This routine uses a hueristic for extracting a good sequence. It should work
on all different versions of the "yuanrap.sys" file, given the way the MT352
tuning sequences are stored in all versions of that file I have seen so far.
However, the current patch simply looks for one specific archive URL.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch should fix 7 MHz DVB-T with the XC3028 using the
DTV7 firmware from the xc3028-v27.fw firmware image.
Tested-by: Terry Wu <terrywu2009@gmail.com>
[mchehab@redhat.com: thanks to John Ferlito, we have a real test in Australia]
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If soc_camera_init_user_formats() fails in soc_camera_probe(), we have to call
client's .remove() method to unregister the video device.
Reported-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The supported formats count must be set to 0 after debug output
right before the second pass.
Signed-off-by: Stefan Herbrechtsmeier <hbmeier@hni.uni-paderborn.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If I2C is not enabled, then we shouldn't build ttpci_eeprom.c.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
precalculate_bars() improved vivi performance. However, it assumed that
always before streaming, the driver would call VIDIOC_S_STD. This is not
an API requirement, and the testing apps don't do that.
Due to that, a regression were caused by the patch that added it.
This patch moves the precalculate_bars to the proper place of the code,
calling it at buffer_prepare() callback.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 537a1bf059 (fbdev: add mutex for
fb_mmap locking) introduces a ->mm_lock mutex for protecting smem
assignments. Unfortunately in the case of sm501fb these happen quite
early in the initialization code, well before the mutex_init() that takes
place in register_framebuffer(), leading to:
Badness at kernel/mutex.c:207
Pid : 1, Comm: swapper
CPU : 0 Not tainted (2.6.31-rc1-00284-g529ba0d-dirty #2273)
PC is at __mutex_lock_slowpath+0x72/0x1bc
PR is at __mutex_lock_slowpath+0x66/0x1bc
...
matroxfb appears to have the same issue and has solved it with an early
mutex_init(), so we do the same for sm501fb.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Fix CONFIG_FLATMEM version of pfn_valid()
MIPS: Reorganize Cavium OCTEON PCI support.
Update Yoichi Yuasa's e-mail address
MIPS: Allow suspend and hibernation again on uniprocessor kernels.
MIPS: 64-bit: Fix o32 core dump
MIPS: BC47xx: Fix SSB irq setup
MIPS: CMP: Update sync-r4k for current kernel
MIPS: CMP: Move gcmp_probe to before the SMP ops
MIPS: CMP: activate CMP support
MIPS: CMP: Extend IPI handling to CPU number
MIPS: CMP: Extend the GIC IPI interrupts beyond 32
MIPS: Define __arch_swab64 for all mips r2 cpus
MIPS: Update VR41xx GPIO driver to use gpiolib
MIPS: Hookup new syscalls sys_rt_tgsigqueueinfo and sys_perf_counter_open.
MIPS: Malta: Remove unnecessary function prototypes
MIPS: MT: Remove unnecessary semicolons
MIPS: Add support for Texas Instruments AR7 System-on-a-Chip
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
sound: do not set DEVNAME for OSS devices
ALSA: hda - Add sanity check in PCM open callback
ALSA: hda - Call snd_pcm_lib_hw_rates() again after codec open callback
ALSA: hda - Avoid invalid formats and rates with shared SPDIF
ALSA: hda - Improve ASUS eeePC 1000 mixer
ALSA: hda - Add GPIO1 control at muting with HP laptops
ALSA: usx2y - reparent sound device
ALSA: snd_usb_caiaq: reparent sound device
sound: virtuoso: fix Xonar D1/DX silence after resume
ASoC: Only disable pxa2xx-i2s clocks if we enabled them
ALSA: hda - Add quirk for HP 6930p
ALSA: hda - Add missing static to patch_ca0110()
ASoC: OMAP: fix OMAP1510 broken PCM pointer callback
ASoC: remove BROKEN from Efika and pcm030 fabric drivers
ASoC: Fix typo in MPC5200 PSC AC97 driver Kconfig
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
kbuild: finally remove the obsolete variable $TOPDIR
gitignore: ignore scripts/ihex2fw
Kbuild: Disable the -Wformat-security gcc flag
gitignore: ignore gcov output files
kbuild: deb-pkg ship changelog
Add new __init_task_data macro to be used in arch init_task.c files.
asm-generic/vmlinux.lds.h: shuffle INIT_TASK* macro names in vmlinux.lds.h
Add new macros for page-aligned data and bss sections.
asm-generic/vmlinux.lds.h: Fix up RW_DATA_SECTION definition.
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: don't merge requests of different failfast settings
cciss: Ignore stale commands after reboot
* fix/hda:
ALSA: hda - Add sanity check in PCM open callback
ALSA: hda - Call snd_pcm_lib_hw_rates() again after codec open callback
ALSA: hda - Avoid invalid formats and rates with shared SPDIF
ALSA: hda - Improve ASUS eeePC 1000 mixer
ALSA: hda - Add GPIO1 control at muting with HP laptops
Add some sanity checks of struct snd_pcm_hardware fields in the PCM
open callback of hda driver. This makes a bit easier to debug any PCM
setup errors in the codec side.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM rates bit field may have been changed by the codec open callback.
In that case, we need to reset rate_min and rate_max. So, simply call
snd_pcm_lib_hw_rates() again after the codec open callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check whether formats and rates don't result in zero due to the
restriction of SPDIF sharing. If any of them can be zero, disable
the SPDIF sharing mode instead. Otherwise it will lead to a PCM
configuration error.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Block layer used to merge requests and bios with different failfast
settings. This caused regular IOs to fail prematurely when they were
merged into failfast requests for readahead.
Niel Lambrechts could trigger the problem semi-reliably on ext4 when
resuming from STR. ext4 uses readahead when reading inodes and
combined with the deterministic extra SATA PHY exception cycle during
resume on the specific configuration, non-readahead inode read would
fail causing ext4 errors. Please read the following thread for
details.
http://lkml.org/lkml/2009/5/23/21
This patch makes block layer reject merging if the failfast settings
don't match. This is correct but likely to lower IO performance by
preventing regular IOs from mingling into surrounding readahead
requests. Changes to allow such mixed merges and handle errors
correctly will be added later.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Niel Lambrechts <niel.lambrechts@gmail.com>
Cc: Theodore Tso <tytso@mit.edu>
Signed-off-by: Jens Axboe <axboe@carl.(none)>
When doing an unexpected shutdown like kexec the cciss
firmware might still have some commands in flight, which
it is trying to complete.
The driver is doing it's best on resetting the HBA,
but sadly there's a firmware issue causing the firmware
_not_ to abort or drop old commands.
So the firmware will send us commands which we haven't
accounted for, causing the driver to panic.
With this patch we're just ignoring these commands as
there is nothing we could be doing with them anyway.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <axboe@carl.(none)>
For systems which do not define PHYS_OFFSET as 0 pfn_valid() may falsely
have returned 0 on most configurations. Bug introduced by commit
752fbeb2e3555c0d236e992f1195fd7ce30e728d (linux-mips.org) rsp.
6f284a2ce7 (kernel.org) titled "[MIPS]
FLATMEM: introduce PHYS_OFFSET."
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the cavium PCI files to the arch/mips/pci directory. Also cleanup
comment formatting and code layout. Code from pci-common.c, was moved
into other files.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If an o32 process generates a core dump on a 64 bit kernel, the core file
will not be correctly recognized. This is because ELF_CORE_COPY_REGS and
ELF_CORE_COPY_TASK_REGS are not correctly defined for o32 and will use
the default register set which would be CONFIG_64BIT in asm/elf.h.
So we'll switch to use the right register defines in this situation by
checking for WANT_COMPAT_REG_H and use the right defines of
ELF_CORE_COPY_REGS and ELF_CORE_COPY_TASK_REGS.
[Ralf: made ELF_CORE_COPY_TASK_REGS() bullet-proof against funny arguments.]
Signed-off-by: Yong Zhang <yong.zhang@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current ssb irq setup in ssb_mipscore_init has the problem that it
configures some device on some irq without checking that the irq is not
taken by an other device.
For example in my case PCI host is on irq 0 and IPSEC on irq 3.
The current code:
- store in dev->irq that IPSEC irq is 3 + 2
- do a set_irq 0->3 on PCI host
But now IPSEC irq is not routed anymore to the mips code and dev->irq is
wrong. This causes a problem described in [1].
This patch tries to solve the problem by making set_irq configure the
device we want to take the irq on the shared irq0. The previous example
becomes:
- store in dev->irq that IPSEC irq is 3 + 2
- do a set_irq 0->3 on PCI host:
- irq 3 is already taken by IPSEC. do a set_irq 3->0 on IPSEC
I also added some code to print the irq configuration after irq setup to
allow easier debugging. And I add extra checking in ssb_mips_irq to report
device without irq or device with not routed irq.
[1] http://www.danm.de/files/src/bcm5365p/REPORTED_DEVICES
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Acked-by : Michael Buesch <mb@bu3sch.de>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This revises the sync-4k so it will boot and operate since the removal of
expirelo from the timer code.
Signed-off-by: Tim Anderson <tanderson@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is to move the gcmp_probe call to before the use of and selection of
the smp_ops functions. This allows malta with 1004K to work.
Signed-off-by: Tim Anderson <tanderson@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most of the CMP support was added before, this mostly correct compile
problems but adds a platform specific translation for the interrupt number
based on cpu number.
Signed-off-by: Tim Anderson <tanderson@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This takes the current IPI interrupt assignment from the fix number of 4
to the number of CPUs defined in the system.
Signed-off-by: Tim Anderson <tanderson@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch extends the GIC interrupt handling beyond the current 32 bit
range as well as extending the number of interrupts based on the number
of CPUs.
Signed-off-by: Tim Anderson <tanderson@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some CPUs implement mipsr2, but because they are a super-set of mips64r2 do
not define CONFIG_CPU_MIPS64_R2. Cavium OCTEON falls into this category.
We would still like to use the optimized implementation, so since we have
already checked for CONFIG_CPU_MIPSR2, checking for CONFIG_64BIT instead of
CONFIG_CPU_MIPS64_R2 is sufficient.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[Ralf: I fixed up the numbering in the comment in scall64-n32.S.]
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the Texas Instruments AR7 System-on-a-Chip.
It supports the TNETD7100, 7200 and 7300 versions of the SoC.
Signed-off-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Eugene Konev <ejka@openwrt.org>
Signed-off-by: Nicolas Thill <nico@openwrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Mauro Carvalho Chehab