Fix error path order in nbp_vlan_init, so if switchdev_port_attr_set
call failes, the vlan_hash wouldn't be destroyed before inited.
Fixes: efa5356b0d ("bridge: per vlan dst_metadata netlink support")
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will add stricter validating for RTA_MARK attribute.
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addr_gen_mode variable can be accessed by both sysctl and netlink.
Repleacd rtnl_lock() with rtnl_trylock() protect the sysctl operation to
avoid the possbile dead lock.`
Signed-off-by: Felix Jia <felix.jia@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
While playing with mlx4 hardware timestamping of RX packets, I found
that some packets were received by TCP stack with a ~200 ms delay...
Since the timestamp was provided by the NIC, and my probe was added
in tcp_v4_rcv() while in BH handler, I was confident it was not
a sender issue, or a drop in the network.
This would happen with a very low probability, but hurting RPC
workloads.
A NAPI driver normally arms the IRQ after the napi_complete_done(),
after NAPI_STATE_SCHED is cleared, so that the hard irq handler can grab
it.
Problem is that if another point in the stack grabs NAPI_STATE_SCHED bit
while IRQ are not disabled, we might have later an IRQ firing and
finding this bit set, right before napi_complete_done() clears it.
This can happen with busy polling users, or if gro_flush_timeout is
used. But some other uses of napi_schedule() in drivers can cause this
as well.
thread 1 thread 2 (could be on same cpu, or not)
// busy polling or napi_watchdog()
napi_schedule();
...
napi->poll()
device polling:
read 2 packets from ring buffer
Additional 3rd packet is
available.
device hard irq
// does nothing because
NAPI_STATE_SCHED bit is owned by thread 1
napi_schedule();
napi_complete_done(napi, 2);
rearm_irq();
Note that rearm_irq() will not force the device to send an additional
IRQ for the packet it already signaled (3rd packet in my example)
This patch adds a new NAPI_STATE_MISSED bit, that napi_schedule_prep()
can set if it could not grab NAPI_STATE_SCHED
Then napi_complete_done() properly reschedules the napi to make sure
we do not miss something.
Since we manipulate multiple bits at once, use cmpxchg() like in
sk_busy_loop() to provide proper transactions.
In v2, I changed napi_watchdog() to use a relaxed variant of
napi_schedule_prep() : No need to set NAPI_STATE_MISSED from this point.
In v3, I added more details in the changelog and clears
NAPI_STATE_MISSED in busy_poll_stop()
In v4, I added the ideas given by Alexander Duyck in v3 review
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variables rds_ib_mr_1m_pool_size and rds_ib_mr_8k_pool_size
are used only in the ib.c file. As such, the static type is
added to limit them in this file.
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit cd2b708750 ("sctp: check duplicate node before inserting a
new transport") called rhltable_lookup() to check for the duplicate
transport node in transport rhashtable.
But rhltable_lookup() doesn't call rcu_read_lock inside, it could cause
a use-after-free issue if it tries to dereference the node that another
cpu has freed it. Note that sock lock can not avoid this as it is per
sock.
This patch is to fix it by calling rcu_read_lock before checking for
duplicate transport nodes.
Fixes: cd2b708750 ("sctp: check duplicate node before inserting a new transport")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the routines by which rxrpc is accessed from the outside are serialised
by means of the socket lock (sendmsg, recvmsg, bind,
rxrpc_kernel_begin_call(), ...) and this presents a problem:
(1) If a number of calls on the same socket are in the process of
connection to the same peer, a maximum of four concurrent live calls
are permitted before further calls need to wait for a slot.
(2) If a call is waiting for a slot, it is deep inside sendmsg() or
rxrpc_kernel_begin_call() and the entry function is holding the socket
lock.
(3) sendmsg() and recvmsg() or the in-kernel equivalents are prevented
from servicing the other calls as they need to take the socket lock to
do so.
(4) The socket is stuck until a call is aborted and makes its slot
available to the waiter.
Fix this by:
(1) Provide each call with a mutex ('user_mutex') that arbitrates access
by the users of rxrpc separately for each specific call.
(2) Make rxrpc_sendmsg() and rxrpc_recvmsg() unlock the socket as soon as
they've got a call and taken its mutex.
Note that I'm returning EWOULDBLOCK from recvmsg() if MSG_DONTWAIT is
set but someone else has the lock. Should I instead only return
EWOULDBLOCK if there's nothing currently to be done on a socket, and
sleep in this particular instance because there is something to be
done, but we appear to be blocked by the interrupt handler doing its
ping?
(3) Make rxrpc_new_client_call() unlock the socket after allocating a new
call, locking its user mutex and adding it to the socket's call tree.
The call is returned locked so that sendmsg() can add data to it
immediately.
From the moment the call is in the socket tree, it is subject to
access by sendmsg() and recvmsg() - even if it isn't connected yet.
(4) Lock new service calls in the UDP data_ready handler (in
rxrpc_new_incoming_call()) because they may already be in the socket's
tree and the data_ready handler makes them live immediately if a user
ID has already been preassigned.
Note that the new call is locked before any notifications are sent
that it is live, so doing mutex_trylock() *ought* to always succeed.
Userspace is prevented from doing sendmsg() on calls that are in a
too-early state in rxrpc_do_sendmsg().
(5) Make rxrpc_new_incoming_call() return the call with the user mutex
held so that a ping can be scheduled immediately under it.
Note that it might be worth moving the ping call into
rxrpc_new_incoming_call() and then we can drop the mutex there.
(6) Make rxrpc_accept_call() take the lock on the call it is accepting and
release the socket after adding the call to the socket's tree. This
is slightly tricky as we've dequeued the call by that point and have
to requeue it.
Note that requeuing emits a trace event.
(7) Make rxrpc_kernel_send_data() and rxrpc_kernel_recv_data() take the
new mutex immediately and don't bother with the socket mutex at all.
This patch has the nice bonus that calls on the same socket are now to some
extent parallelisable.
Note that we might want to move rxrpc_service_prealloc() calls out from the
socket lock and give it its own lock, so that we don't hang progress in
other calls because we're waiting for the allocator.
We probably also want to avoid calling rxrpc_notify_socket() from within
the socket lock (rxrpc_accept_call()).
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Marc Dionne <marc.c.dionne@auristor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull IDR rewrite from Matthew Wilcox:
"The most significant part of the following is the patch to rewrite the
IDR & IDA to be clients of the radix tree. But there's much more,
including an enhancement of the IDA to be significantly more space
efficient, an IDR & IDA test suite, some improvements to the IDR API
(and driver changes to take advantage of those improvements), several
improvements to the radix tree test suite and RCU annotations.
The IDR & IDA rewrite had a good spin in linux-next and Andrew's tree
for most of the last cycle. Coupled with the IDR test suite, I feel
pretty confident that any remaining bugs are quite hard to hit. 0-day
did a great job of watching my git tree and pointing out problems; as
it hit them, I added new test-cases to be sure not to be caught the
same way twice"
Willy goes on to expand a bit on the IDR rewrite rationale:
"The radix tree and the IDR use very similar data structures.
Merging the two codebases lets us share the memory allocation pools,
and results in a net deletion of 500 lines of code. It also opens up
the possibility of exposing more of the features of the radix tree to
users of the IDR (and I have some interesting patches along those
lines waiting for 4.12)
It also shrinks the size of the 'struct idr' from 40 bytes to 24 which
will shrink a fair few data structures that embed an IDR"
* 'idr-4.11' of git://git.infradead.org/users/willy/linux-dax: (32 commits)
radix tree test suite: Add config option for map shift
idr: Add missing __rcu annotations
radix-tree: Fix __rcu annotations
radix-tree: Add rcu_dereference and rcu_assign_pointer calls
radix tree test suite: Run iteration tests for longer
radix tree test suite: Fix split/join memory leaks
radix tree test suite: Fix leaks in regression2.c
radix tree test suite: Fix leaky tests
radix tree test suite: Enable address sanitizer
radix_tree_iter_resume: Fix out of bounds error
radix-tree: Store a pointer to the root in each node
radix-tree: Chain preallocated nodes through ->parent
radix tree test suite: Dial down verbosity with -v
radix tree test suite: Introduce kmalloc_verbose
idr: Return the deleted entry from idr_remove
radix tree test suite: Build separate binaries for some tests
ida: Use exceptional entries for small IDAs
ida: Move ida_bitmap to a percpu variable
Reimplement IDR and IDA using the radix tree
radix-tree: Add radix_tree_iter_delete
...
bugfixes.
A couple changes could theoretically break working setups on upgrade. I
don't expect complaints in practice, but they seem worth calling out
just in case:
- NFS security labels are now off by default; a new
security_label export flag reenables it per export. But,
having them on by default is a disaster, as it generally only
makes sense if all your clients and servers have similar
enough selinux policies. Thanks to Jason Tibbitts for
pointing this out.
- NFSv4/UDP support is off. It was never really supported, and
the spec explicitly forbids it. We only ever left it on out
of laziness; thanks to Jeff Layton for finally fixing that.
-----BEGIN PGP SIGNATURE-----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=iLLz
-----END PGP SIGNATURE-----
Merge tag 'nfsd-4.11' of git://linux-nfs.org/~bfields/linux
Pull nfsd updates from Bruce Fields:
"The nfsd update this round is mainly a lot of miscellaneous cleanups
and bugfixes.
A couple changes could theoretically break working setups on upgrade.
I don't expect complaints in practice, but they seem worth calling out
just in case:
- NFS security labels are now off by default; a new security_label
export flag reenables it per export. But, having them on by default
is a disaster, as it generally only makes sense if all your clients
and servers have similar enough selinux policies. Thanks to Jason
Tibbitts for pointing this out.
- NFSv4/UDP support is off. It was never really supported, and the
spec explicitly forbids it. We only ever left it on out of
laziness; thanks to Jeff Layton for finally fixing that"
* tag 'nfsd-4.11' of git://linux-nfs.org/~bfields/linux: (34 commits)
nfsd: Fix display of the version string
nfsd: fix configuration of supported minor versions
sunrpc: don't register UDP port with rpcbind when version needs congestion control
nfs/nfsd/sunrpc: enforce transport requirements for NFSv4
sunrpc: flag transports as having congestion control
sunrpc: turn bitfield flags in svc_version into bools
nfsd: remove superfluous KERN_INFO
nfsd: special case truncates some more
nfsd: minor nfsd_setattr cleanup
NFSD: Reserve adequate space for LOCKT operation
NFSD: Get response size before operation for all RPCs
nfsd/callback: Drop a useless data copy when comparing sessionid
nfsd/callback: skip the callback tag
nfsd/callback: Cleanup callback cred on shutdown
nfsd/idmap: return nfserr_inval for 0-length names
SUNRPC/Cache: Always treat the invalid cache as unexpired
SUNRPC: Drop all entries from cache_detail when cache_purge()
svcrdma: Poll CQs in "workqueue" mode
svcrdma: Combine list fields in struct svc_rdma_op_ctxt
svcrdma: Remove unused sc_dto_q field
...
- support for rbd data-pool feature, which enables rbd images on
erasure-coded pools (myself). CEPH_PG_MAX_SIZE has been bumped to
allow erasure-coded profiles with k+m up to 32.
- a patch for ceph_d_revalidate() performance regression introduced in
4.9, along with some cleanups in the area (Jeff Layton)
- a set of fixes for unsafe ->d_parent accesses in CephFS (Jeff Layton)
- buffered reads are now processed in rsize windows instead of rasize
windows (Andreas Gerstmayr). The new default for rsize mount option
is 64M.
- ack vs commit distinction is gone, greatly simplifying ->fsync() and
MOSDOpReply handling code (myself)
Also a few filesystem bug fixes from Zheng, a CRUSH sync up (CRUSH
computations are still serialized though) and several minor fixes and
cleanups all over.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJYtY0rAAoJEEp/3jgCEfOLQioH/36QKsalquY1FCdJnJve9qj0
q19OohamIedhv76AYvXhJzBBHlVwerjicE51/bSzuUhxV+ApdATrPPcLC22oLd3i
h0R9NAUMYjiris1yN/Z9JRiPCSdsxvHuRycsUMRSRbxZhnyP9XdTxFD1A+fLfisU
Z4osyTzadabVL5Um9maRBbAtXCWh3d9JZzPa5xIvWTEO4CWWk87GtEIIQDcgx+Y6
8ZSMmrVFDNtskUp9js+LnFYW7/xBsEXyqgsqKaecf5uQqwu1WKRXSKtv9PUmGAIb
HBrlUdV1PQaCzTYtaoztJshNdYcphM5L7gePzxRG0nXrTNsq8J5eCzI8en5qS8w=
=CPL/
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-4.11-rc1' of git://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"This time around we have:
- support for rbd data-pool feature, which enables rbd images on
erasure-coded pools (myself). CEPH_PG_MAX_SIZE has been bumped to
allow erasure-coded profiles with k+m up to 32.
- a patch for ceph_d_revalidate() performance regression introduced
in 4.9, along with some cleanups in the area (Jeff Layton)
- a set of fixes for unsafe ->d_parent accesses in CephFS (Jeff
Layton)
- buffered reads are now processed in rsize windows instead of rasize
windows (Andreas Gerstmayr). The new default for rsize mount option
is 64M.
- ack vs commit distinction is gone, greatly simplifying ->fsync()
and MOSDOpReply handling code (myself)
... also a few filesystem bug fixes from Zheng, a CRUSH sync up (CRUSH
computations are still serialized though) and several minor fixes and
cleanups all over"
* tag 'ceph-for-4.11-rc1' of git://github.com/ceph/ceph-client: (52 commits)
libceph, rbd, ceph: WRITE | ONDISK -> WRITE
libceph: get rid of ack vs commit
ceph: remove special ack vs commit behavior
ceph: tidy some white space in get_nonsnap_parent()
crush: fix dprintk compilation
crush: do is_out test only if we do not collide
ceph: remove req from unsafe list when unregistering it
rbd: constify device_type structure
rbd: kill obj_request->object_name and rbd_segment_name_cache
rbd: store and use obj_request->object_no
rbd: RBD_V{1,2}_DATA_FORMAT macros
rbd: factor out __rbd_osd_req_create()
rbd: set offset and length outside of rbd_obj_request_create()
rbd: support for data-pool feature
rbd: introduce rbd_init_layout()
rbd: use rbd_obj_bytes() more
rbd: remove now unused rbd_obj_request_wait() and helpers
rbd: switch rbd_obj_method_sync() to ceph_osdc_call()
libceph: pass reply buffer length through ceph_osdc_call()
rbd: do away with obj_request in rbd_obj_read_sync()
...
Pull networking fixes from David Miller:
1) Don't save TIPC header values before the header has been validated,
from Jon Paul Maloy.
2) Fix memory leak in RDS, from Zhu Yanjun.
3) We miss to initialize the UID in the flow key in some paths, from
Julian Anastasov.
4) Fix latent TOS masking bug in the routing cache removal from years
ago, also from Julian.
5) We forget to set the sockaddr port in sctp_copy_local_addr_list(),
fix from Xin Long.
6) Missing module ref count drop in packet scheduler actions, from
Roman Mashak.
7) Fix RCU annotations in rht_bucket_nested, from Herbert Xu.
8) Fix use after free which happens because L2TP's ipv4 support returns
non-zero values from it's backlog_rcv function which ipv4 interprets
as protocol values. Fix from Paul Hüber.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
qed: Don't use attention PTT for configuring BW
qed: Fix race with multiple VFs
l2tp: avoid use-after-free caused by l2tp_ip_backlog_recv
xfrm: provide correct dst in xfrm_neigh_lookup
rhashtable: Fix RCU dereference annotation in rht_bucket_nested
rhashtable: Fix use before NULL check in bucket_table_free
net sched actions: do not overwrite status of action creation.
rxrpc: Kernel calls get stuck in recvmsg
net sched actions: decrement module reference count after table flush.
lib: Allow compile-testing of parman
ipv6: check sk sk_type and protocol early in ip_mroute_set/getsockopt
sctp: set sin_port for addr param when checking duplicate address
net/mlx4_en: fix overflow in mlx4_en_init_timestamp()
netfilter: nft_set_bitmap: incorrect bitmap size
net: s2io: fix typo argumnet argument
net: vxge: fix typo argumnet argument
netfilter: nf_ct_expect: Change __nf_ct_expect_check() return value.
ipv4: mask tos for input route
ipv4: add missing initialization for flowi4_uid
lib: fix spelling mistake: "actualy" -> "actually"
...
inet_sk(skb->sk) is illegal in case skb is attached to request socket.
Fixes: ca6fb06518 ("tcp: attach SYNACK messages to request sockets instead of listener")
Reported by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When I originally introduced using the driver-indicated station as an
optimisation to avoid the hashtable lookup/iteration, of course it
wasn't intended to really functionally change anything.
I neglected, however, to take into account VLAN interfaces, which have
the property that management and data frames are handled differently:
data frames go directly to the station and the VLAN while management
frames continue to be processed over the underlying/associated AP-type
interface. As a consequence, when a driver used this optimisation for
management frames and the user enabled VLANs, my change broke things
since any management frames, particularly disassoc/deauth, were missed
by hostapd.
Fix this by restoring the original code path for non-data frames, they
aren't critical for performance to begin with.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=194713.
Big thanks goes to Jarek who bisected the issue and provided a very
detailed bug report, including the crucial information that he was
using VLANs in his configuration.
Cc: stable@vger.kernel.org
Fixes: 771e846bea9e ("mac80211: allow passing transmitter station on RX")
Reported-and-tested-by: Jarek Kamiński <jarek@freeside.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.
Use BUILD_BUG_ON in a couple ATM drivers.
In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement. Hopefully this patch inspires
someone else to trim vsprintf.c more.
Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
varible||variable
While we are here, tidy up the comment blocks that fit in a single line
for drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c and
net/sctp/transport.c.
Link: http://lkml.kernel.org/r/1481573103-11329-11-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
aligment||alignment
I did not touch the "N_BYTE_ALIGMENT" macro in
drivers/net/wireless/realtek/rtlwifi/wifi.h to avoid unpredictable
impact.
I fixed "_aligment_handler" in arch/openrisc/kernel/entry.S because
it is surrounded by #if 0 ... #endif. It is surely safe and I
confirmed "_alignment_handler" is correct.
I also fixed the "controler" I found in the same hunk in
arch/openrisc/kernel/head.S.
Link: http://lkml.kernel.org/r/1481573103-11329-8-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
an user||a user
an userspace||a userspace
I also added "userspace" to the list since it is a common word in Linux.
I found some instances for "an userfaultfd", but I did not add it to the
list. I felt it is endless to find words that start with "user" such as
"userland" etc., so must draw a line somewhere.
Link: http://lkml.kernel.org/r/1481573103-11329-4-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
swith||switch
swithable||switchable
swithed||switched
swithing||switching
While we are here, fix the "update" to "updates" in the touched hunk in
drivers/net/wireless/marvell/mwifiex/wmm.c.
Link: http://lkml.kernel.org/r/1481573103-11329-2-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a struct irq_affinity pointer to the find_vqs methods, which if set
is used to tell the PCI layer to create the MSI-X vectors for our I/O
virtqueues with the proper affinity from the start. Compared to after
the fact affinity hints this gives us an instantly working setup and
allows to allocate the irq descritors node-local and avoid interconnect
traffic. Last but not least this will allow blk-mq queues are created
based on the interrupt affinity for storage drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains netfilter fixes for you net tree,
they are:
1) Missing ct zone size in the nft_ct initialization path, patch
from Florian Westphal.
2) Two patches for netfilter uapi headers, one to remove unnecessary
sysctl.h inclusion and another to fix compilation of xt_hashlimit.h
in userspace, from Dmitry V. Levin.
3) Patch to fix a sloppy change in nf_ct_expect that incorrectly
simplified nf_ct_expect_related_report() in the previous nf-next
batch. This also includes another patch for __nf_ct_expect_check()
to report success by returning 0 to keep it consistent with other
existing functions. From Jarno Rajahalme.
4) The ->walk() iterator of the new bitmap set type goes over the real
bitmap size, this results in incorrect dumps when NFTA_SET_USERDATA
is used.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tracing is limited to 100 characters and this message passes
the limit when there are a few buffered frames. Shorten it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwlwifi now supports RSS and can't let mac80211 track the
PS state based on the Rx frames since they can come out of
order. iwlwifi is now advertising AP_LINK_PS, and uses
explicit notifications to teach mac80211 about the PS state
of the stations and the PS poll / uAPSD trigger frames
coming our way from the peers.
Because of that, the TIM stopped being maintained in
mac80211. I tried to fix this in commit c68df2e7be
("mac80211: allow using AP_LINK_PS with mac80211-generated TIM IE")
but that was later reverted by Felix in commit 6c18a6b4e7
("Revert "mac80211: allow using AP_LINK_PS with mac80211-generated TIM IE")
since it broke drivers that do not implement set_tim.
Since none of the drivers that set AP_LINK_PS have the
set_tim() handler set besides iwlwifi, I can bail out in
__sta_info_recalc_tim if AP_LINK_PS AND .set_tim is not
implemented.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When running a BA session, the driver (or the hardware) already takes
care of retransmitting failed frames, since it has to keep the receiver
reorder window in sync.
Adding another layer of retransmit around that does not improve
anything. In fact, it can only lead to some strong reordering with huge
latency.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When RX aggregation starts, transmitter may continue send frames
with SN smaller than SSN until the AddBA response is received.
However, the reorder buffer is already initialized at this point,
which will cause the drop of such frames as duplicates since the
head SN of the reorder buffer is set to the SSN, which is bigger.
Cc: stable@vger.kernel.org
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The issue was found when entering suspend and resume.
It triggers a warning in:
mac80211/key.c: ieee80211_enable_keys()
...
WARN_ON_ONCE(sdata->crypto_tx_tailroom_needed_cnt ||
sdata->crypto_tx_tailroom_pending_dec);
...
It points out sdata->crypto_tx_tailroom_pending_dec isn't cleaned up successfully
in a delayed_work during suspend. Add a flush_delayed_work to fix it.
Cc: stable@vger.kernel.org
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When adding per-CPU statistics, which added statistics back
to mac80211 for the fast-RX path, I evidently forgot to add
the "stats->packets++" line. The reason for that is likely
that I didn't see it since it's done in defragmentation for
the regular RX path.
Add the missing line to properly count received packets in
the fast-RX case.
Fixes: c9c5962b56 ("mac80211: enable collecting station statistics per-CPU")
Reported-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
l2tp_ip_backlog_recv may not return -1 if the packet gets dropped.
The return value is passed up to ip_local_deliver_finish, which treats
negative values as an IP protocol number for resubmission.
Signed-off-by: Paul Hüber <phueber@kernsp.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix xfrm_neigh_lookup to provide dst->path to the
neigh_lookup dst_ops method.
When skb is provided, the IP address in packet should already
match the dst->path address family. But for the non-skb case,
we should consider the last tunnel address as nexthop address.
Fixes: f894cbf847 ("net: Add optional SKB arg to dst_ops->neigh_lookup().")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calls made through the in-kernel interface can end up getting stuck because
of a missed variable update in a loop in rxrpc_recvmsg_data(). The problem
is like this:
(1) A new packet comes in and doesn't cause a notification to be given to
the client as there's still another packet in the ring - the
assumption being that if the client will keep drawing off data until
the ring is empty.
(2) The client is in rxrpc_recvmsg_data(), inside the big while loop that
iterates through the packets. This copies the window pointers into
variables rather than using the information in the call struct
because:
(a) MSG_PEEK might be in effect;
(b) we need a barrier after reading call->rx_top to pair with the
barrier in the softirq routine that loads the buffer.
(3) The reading of call->rx_top is done outside of the loop, and top is
never updated whilst we're in the loop. This means that even through
there's a new packet available, we don't see it and may return -EFAULT
to the caller - who will happily return to the scheduler and await the
next notification.
(4) No further notifications are forthcoming until there's an abort as the
ring isn't empty.
The fix is to move the read of call->rx_top inside the loop - but it needs
to be done before the condition is checked.
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tc actions are loaded as a module and no actions have been installed,
flushing them would result in actions removed from the memory, but modules
reference count not being decremented, so that the modules would not be
unloaded.
Following is example with GACT action:
% sudo modprobe act_gact
% lsmod
Module Size Used by
act_gact 16384 0
%
% sudo tc actions ls action gact
%
% sudo tc actions flush action gact
% lsmod
Module Size Used by
act_gact 16384 1
% sudo tc actions flush action gact
% lsmod
Module Size Used by
act_gact 16384 2
% sudo rmmod act_gact
rmmod: ERROR: Module act_gact is in use
....
After the fix:
% lsmod
Module Size Used by
act_gact 16384 0
%
% sudo tc actions add action pass index 1
% sudo tc actions add action pass index 2
% sudo tc actions add action pass index 3
% lsmod
Module Size Used by
act_gact 16384 3
%
% sudo tc actions flush action gact
% lsmod
Module Size Used by
act_gact 16384 0
%
% sudo tc actions flush action gact
% lsmod
Module Size Used by
act_gact 16384 0
% sudo rmmod act_gact
% lsmod
Module Size Used by
%
Fixes: f97017cdef ("net-sched: Fix actions flushing")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5e1859fbcc ("ipv4: ipmr: various fixes and cleanups") fixed
the issue for ipv4 ipmr:
ip_mroute_setsockopt() & ip_mroute_getsockopt() should not
access/set raw_sk(sk)->ipmr_table before making sure the socket
is a raw socket, and protocol is IGMP
The same fix should be done for ipv6 ipmr as well.
This patch can fix the panic caused by overwriting the same offset
as ipmr_table as in raw_sk(sk) when accessing other type's socket
by ip_mroute_setsockopt().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b8607805dd ("sctp: not copying duplicate addrs to the assoc's
bind address list") tried to check for duplicate address before copying
to asoc's bind_addr list from global addr list.
But all the addrs' sin_ports in global addr list are 0 while the addrs'
sin_ports are bp->port in asoc's bind_addr list. It means even if it's
a duplicate address, af->cmp_addr will still return 0 as the their
sin_ports are different.
This patch is to fix it by setting the sin_port for addr param with
bp->port before comparing the addrs.
Fixes: b8607805dd ("sctp: not copying duplicate addrs to the assoc's bind address list")
Reported-by: Wei Chen <weichen@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
priv->bitmap_size stores the real bitmap size, instead of the full
struct nft_bitmap object.
Fixes: 665153ff57 ("netfilter: nf_tables: add bitmap set type")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Commit 4dee62b1b9 ("netfilter: nf_ct_expect: nf_ct_expect_insert()
returns void") inadvertently changed the successful return value of
nf_ct_expect_related_report() from 0 to 1 due to
__nf_ct_expect_check() returning 1 on success. Prevent this
regression in the future by changing the return value of
__nf_ct_expect_check() to 0 on success.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Restore the lost masking of TOS in input route code to
allow ip rules to match it properly.
Problem [1] noticed by Shmulik Ladkani <shmulik.ladkani@gmail.com>
[1] http://marc.info/?t=137331755300040&r=1&w=2
Fixes: 89aef8921b ("ipv4: Delete routing cache.")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid matching of random stack value for uid when rules
are looked up on input route or when RP filter is used.
Problem should affect only setups that use ip rules with
uid range.
Fixes: 622ec2c9d5 ("net: core: add UID to flows, rules, and routes")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes
it was possible to remove the IB DMA mapping code entirely and
switch the RDMA stack to use the core DMA mapping code. This resulted
in a nice set of cleanups, but touched the entire tree. This branch
will be submitted separately to Linus at the end of the merge window
as per normal practice for tree wide changes like this.
-----BEGIN PGP SIGNATURE-----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=e0Si
-----END PGP SIGNATURE-----
Merge tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma DMA mapping updates from Doug Ledford:
"Drop IB DMA mapping code and use core DMA code instead.
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes it
was possible to remove the IB DMA mapping code entirely and switch the
RDMA stack to use the core DMA mapping code.
This resulted in a nice set of cleanups, but touched the entire tree
and has been kept separate for that reason."
* tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (37 commits)
IB/rxe, IB/rdmavt: Use dma_virt_ops instead of duplicating it
IB/core: Remove ib_device.dma_device
nvme-rdma: Switch from dma_device to dev.parent
RDS: net: Switch from dma_device to dev.parent
IB/srpt: Modify a debug statement
IB/srp: Switch from dma_device to dev.parent
IB/iser: Switch from dma_device to dev.parent
IB/IPoIB: Switch from dma_device to dev.parent
IB/rxe: Switch from dma_device to dev.parent
IB/vmw_pvrdma: Switch from dma_device to dev.parent
IB/usnic: Switch from dma_device to dev.parent
IB/qib: Switch from dma_device to dev.parent
IB/qedr: Switch from dma_device to dev.parent
IB/ocrdma: Switch from dma_device to dev.parent
IB/nes: Remove a superfluous assignment statement
IB/mthca: Switch from dma_device to dev.parent
IB/mlx5: Switch from dma_device to dev.parent
IB/mlx4: Switch from dma_device to dev.parent
IB/i40iw: Remove a superfluous assignment statement
IB/hns: Switch from dma_device to dev.parent
...
Commit 4dee62b1b9 ("netfilter: nf_ct_expect: nf_ct_expect_insert()
returns void") inadvertently changed the successful return value of
nf_ct_expect_related_report() from 0 to 1, which caused openvswitch
conntrack integration fail in FTP test cases.
Fix this by always returning zero on the success code path.
Fixes: 4dee62b1b9 ("netfilter: nf_ct_expect: nf_ct_expect_insert() returns void")
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
NFSv4 requires a transport "that is specified to avoid network
congestion" (RFC 7530, section 3.1, paragraph 2). In practical terms,
that means that you should not run NFSv4 over UDP. The server has never
enforced that requirement, however.
This patchset fixes this by adding a new flag to the svc_version that
states that it has these transport requirements. With that, we can check
that the transport has XPT_CONG_CTRL set before processing an RPC. If it
doesn't we reject it with RPC_PROG_MISMATCH.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
NFSv4 requires a transport protocol with congestion control in most
cases.
On an IP network, that means that NFSv4 over UDP should be forbidden.
The situation with RDMA is a bit more nuanced, but most RDMA transports
are suitable for this. For now, we assume that all RDMA transports are
suitable, but we may need to revise that at some point.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
It's just simpler to read this way, IMO. Also, no need to explicitly
set vs_hidden to false in the nfsacl ones.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
When the function register_netdevice_notifier fails, the memory
allocated by kmem_cache_create should be freed by the function
kmem_cache_destroy.
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CEPH_OSD_FLAG_ONDISK is set in account_request().
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
- CEPH_OSD_FLAG_ACK shouldn't be set anymore, so assert on it
- remove support for handling ack replies (OSDs will send ack replies
only if clients request them)
- drop the "do lingering callbacks under osd->lock" logic from
handle_reply() -- lreq->lock is sufficient in all three cases
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Align vti6 with vti by returning GRE_KEY flag. This enables iproute2
to display tunnel keys on "ip -6 tunnel show"
Signed-off-by: David Forster <dforster@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the rxrpc_read() function, which allows a user to read the contents of a
key, we miscalculate the expected length of an encoded rxkad token by not
taking into account the key length. However, the data is stored later
anyway with an ENCODE_DATA() call - and an assertion failure then ensues
when the lengths are checked at the end.
Fix this by including the key length in the token size estimation.
The following assertion is produced:
Assertion failed - 384(0x180) == 380(0x17c) is false
------------[ cut here ]------------
kernel BUG at ../net/rxrpc/key.c:1221!
invalid opcode: 0000 [#1] SMP
Modules linked in:
CPU: 2 PID: 2957 Comm: keyctl Not tainted 4.10.0-fscache+ #483
Hardware name: ASUS All Series/H97-PLUS, BIOS 2306 10/09/2014
task: ffff8804013a8500 task.stack: ffff8804013ac000
RIP: 0010:rxrpc_read+0x10de/0x11b6
RSP: 0018:ffff8804013afe48 EFLAGS: 00010296
RAX: 000000000000003b RBX: 0000000000000003 RCX: 0000000000000000
RDX: 0000000000040001 RSI: 00000000000000f6 RDI: 0000000000000300
RBP: ffff8804013afed8 R08: 0000000000000001 R09: 0000000000000001
R10: ffff8804013afd90 R11: 0000000000000002 R12: 00005575f7c911b4
R13: 00005575f7c911b3 R14: 0000000000000157 R15: ffff880408a5d640
FS: 00007f8dfbc73700(0000) GS:ffff88041fb00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00005575f7c91008 CR3: 000000040120a000 CR4: 00000000001406e0
Call Trace:
keyctl_read_key+0xb6/0xd7
SyS_keyctl+0x83/0xe7
do_syscall_64+0x80/0x191
entry_SYSCALL64_slow_path+0x25/0x25
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the function tipc_rcv() we initialize a couple of stack variables
from the message header before that same header has been validated.
In rare cases when the arriving header is non-linar, the validation
function itself may linearize the buffer by calling skb_may_pull(),
while the wrongly initialized stack fields are not updated accordingly.
We fix this in this commit.
Reported-by: Matthew Wong <mwong@sonusnet.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/rds/ib.c:115:2-7: WARNING: NULL check before freeing functions like kfree, debugfs_remove, debugfs_remove_recursive or usb_free_urb is not needed. Maybe consider reorganizing relevant code to avoid passing NULL values.
NULL check before some freeing functions is not needed.
Based on checkpatch warning
"kfree(NULL) is safe this check is probably not required"
and kfreeaddr.cocci by Julia Lawall.
Generated by: scripts/coccinelle/free/ifnullfree.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 2dcab59848 ("sctp: avoid BUG_ON on sctp_wait_for_sndbuf")
attempted to avoid a BUG_ON call when the association being used for a
sendmsg() is blocked waiting for more sndbuf and another thread did a
peeloff operation on such asoc, moving it to another socket.
As Ben Hutchings noticed, then in such case it would return without
locking back the socket and would cause two unlocks in a row.
Further analysis also revealed that it could allow a double free if the
application managed to peeloff the asoc that is created during the
sendmsg call, because then sctp_sendmsg() would try to free the asoc
that was created only for that call.
This patch takes another approach. It will deny the peeloff operation
if there is a thread sleeping on the asoc, so this situation doesn't
exist anymore. This avoids the issues described above and also honors
the syscalls that are already being handled (it can be multiple sendmsg
calls).
Joint work with Xin Long.
Fixes: 2dcab59848 ("sctp: avoid BUG_ON on sctp_wait_for_sndbuf")
Cc: Alexander Popov <alex.popov@linux.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The syntax error was not noticed because dprintk is a macro
and the code is discarded by default.
Reflects ceph.git commit f29b840c64a933b2cb13e3da6f3d785effd73a57.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The is_out() test may require an additional hashing operation, so we
should skip it whenever possible.
Reflects ceph.git commit db107cc7f15cf2481894add325dc93e33479f529.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Dan reports:
net/netfilter/nft_ct.c:549 nft_ct_set_init()
error: uninitialized symbol 'len'.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: edee4f1e92 ("netfilter: nft_ct: add zone id set support")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fix a typo. xdp->data instead of xdp should be copied to the perf-event's
dst_buff.
Fixes: 4de1696952 ("bpf: enable event output helper also for xdp types")
Reported-by: Huapeng Zhou <hzhou@fb.com>
Tested-by: Feixiong Zhang <feixiong@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Revisit warning logic when not applying default helper assignment.
Jiri Kosina considers we are breaking existing setups and not warning
our users accordinly now that automatic helper assignment has been
turned off by default. So let's make him happy by spotting the warning
by when we find a helper but we cannot attach, instead of warning on the
former deprecated behaviour. Patch from Jiri Kosina.
2) Two patches to fix regression in ctnetlink interfaces with
nfnetlink_queue. Specifically, perform more relaxed in CTA_STATUS
and do not bail out if CTA_HELP indicates the same helper that we
already have. Patches from Kevin Cernekee.
3) A couple of bugfixes for ipset via Jozsef Kadlecsik. Due to wrong
index logic in hash set types and null pointer exception in the
list:set type.
4) hashlimit bails out with correct userspace parameters due to wrong
arithmetics in the code that avoids "divide by zero" when
transforming the userspace timing in milliseconds to token credits.
Patch from Alban Browaeys.
5) Fix incorrect NFQA_VLAN_MAX definition, patch from
Ken-ichirou MATSUZAWA.
6) Don't not declare nfnetlink batch error list as static, since this
may be used by several subsystems at the same time. Patch from
Liping Zhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We can get SYN with zero tsecr, don't apply offset in this case.
Fixes: ee684b6f28 ("tcp: send packets with a socket timestamp")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Found that when randomized tcp offsets are enabled (by default)
TCP client can still start new connections without them. Later,
if server does active close and re-uses sockets in TIME-WAIT
state, new SYN from client can be rejected on PAWS check inside
tcp_timewait_state_process(), because either tw_ts_recent or
rcv_tsval doesn't really have an offset set.
Here is how to reproduce it with LTP netstress tool:
netstress -R 1 &
netstress -H 127.0.0.1 -lr 1000000 -a1
[...]
< S seq 1956977072 win 43690 TS val 295618 ecr 459956970
> . ack 1956911535 win 342 TS val 459967184 ecr 1547117608
< R seq 1956911535 win 0 length 0
+1. < S seq 1956977072 win 43690 TS val 296640 ecr 459956970
> S. seq 657450664 ack 1956977073 win 43690 TS val 459968205 ecr 296640
Fixes: 95a22caee3 ("tcp: randomize tcp timestamp offsets for each connection")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DCCP doesn't purge timewait sockets on network namespace shutdown.
So, after net namespace destroyed we could still have an active timer
which will trigger use after free in tw_timer_handler():
BUG: KASAN: use-after-free in tw_timer_handler+0x4a/0xa0 at addr ffff88010e0d1e10
Read of size 8 by task swapper/1/0
Call Trace:
__asan_load8+0x54/0x90
tw_timer_handler+0x4a/0xa0
call_timer_fn+0x127/0x480
expire_timers+0x1db/0x2e0
run_timer_softirq+0x12f/0x2a0
__do_softirq+0x105/0x5b4
irq_exit+0xdd/0xf0
smp_apic_timer_interrupt+0x57/0x70
apic_timer_interrupt+0x90/0xa0
Object at ffff88010e0d1bc0, in cache net_namespace size: 6848
Allocated:
save_stack_trace+0x1b/0x20
kasan_kmalloc+0xee/0x180
kasan_slab_alloc+0x12/0x20
kmem_cache_alloc+0x134/0x310
copy_net_ns+0x8d/0x280
create_new_namespaces+0x23f/0x340
unshare_nsproxy_namespaces+0x75/0xf0
SyS_unshare+0x299/0x4f0
entry_SYSCALL_64_fastpath+0x18/0xad
Freed:
save_stack_trace+0x1b/0x20
kasan_slab_free+0xae/0x180
kmem_cache_free+0xb4/0x350
net_drop_ns+0x3f/0x50
cleanup_net+0x3df/0x450
process_one_work+0x419/0xbb0
worker_thread+0x92/0x850
kthread+0x192/0x1e0
ret_from_fork+0x2e/0x40
Add .exit_batch hook to dccp_v4_ops()/dccp_v6_ops() which will purge
timewait sockets on net namespace destruction and prevent above issue.
Fixes: f2bf415cfe ("mib: add net to NET_ADD_STATS_BH")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While destroying a network namespace that contains a L2TP tunnel a
"BUG: scheduling while atomic" can be observed.
Enabling lockdep shows that this is happening because l2tp_exit_net()
is calling l2tp_tunnel_closeall() (via l2tp_tunnel_delete()) from
within an RCU critical section.
l2tp_exit_net() takes rcu_read_lock_bh()
<< list_for_each_entry_rcu() >>
l2tp_tunnel_delete()
l2tp_tunnel_closeall()
__l2tp_session_unhash()
synchronize_rcu() << Illegal inside RCU critical section >>
BUG: sleeping function called from invalid context
in_atomic(): 1, irqs_disabled(): 0, pid: 86, name: kworker/u16:2
INFO: lockdep is turned off.
CPU: 2 PID: 86 Comm: kworker/u16:2 Tainted: G W O 4.4.6-at1 #2
Hardware name: Xen HVM domU, BIOS 4.6.1-xs125300 05/09/2016
Workqueue: netns cleanup_net
0000000000000000 ffff880202417b90 ffffffff812b0013 ffff880202410ac0
ffffffff81870de8 ffff880202417bb8 ffffffff8107aee8 ffffffff81870de8
0000000000000c51 0000000000000000 ffff880202417be0 ffffffff8107b024
Call Trace:
[<ffffffff812b0013>] dump_stack+0x85/0xc2
[<ffffffff8107aee8>] ___might_sleep+0x148/0x240
[<ffffffff8107b024>] __might_sleep+0x44/0x80
[<ffffffff810b21bd>] synchronize_sched+0x2d/0xe0
[<ffffffff8109be6d>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff8105c7bb>] ? __local_bh_enable_ip+0x6b/0xc0
[<ffffffff816a1b00>] ? _raw_spin_unlock_bh+0x30/0x40
[<ffffffff81667482>] __l2tp_session_unhash+0x172/0x220
[<ffffffff81667397>] ? __l2tp_session_unhash+0x87/0x220
[<ffffffff8166888b>] l2tp_tunnel_closeall+0x9b/0x140
[<ffffffff81668c74>] l2tp_tunnel_delete+0x14/0x60
[<ffffffff81668dd0>] l2tp_exit_net+0x110/0x270
[<ffffffff81668d5c>] ? l2tp_exit_net+0x9c/0x270
[<ffffffff815001c3>] ops_exit_list.isra.6+0x33/0x60
[<ffffffff81501166>] cleanup_net+0x1b6/0x280
...
This bug can easily be reproduced with a few steps:
$ sudo unshare -n bash # Create a shell in a new namespace
# ip link set lo up
# ip addr add 127.0.0.1 dev lo
# ip l2tp add tunnel remote 127.0.0.1 local 127.0.0.1 tunnel_id 1 \
peer_tunnel_id 1 udp_sport 50000 udp_dport 50000
# ip l2tp add session name foo tunnel_id 1 session_id 1 \
peer_session_id 1
# ip link set foo up
# exit # Exit the shell, in turn exiting the namespace
$ dmesg
...
[942121.089216] BUG: scheduling while atomic: kworker/u16:3/13872/0x00000200
...
To fix this, move the call to l2tp_tunnel_closeall() out of the RCU
critical section, and instead call it from l2tp_tunnel_del_work(), which
is running from the l2tp_wq workqueue.
Fixes: 2b551c6e7d ("l2tp: close sessions before initiating tunnel delete")
Signed-off-by: Ridge Kennedy <ridge.kennedy@alliedtelesis.co.nz>
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights:
1) Support TX_RING in AF_PACKET TPACKET_V3 mode, from Sowmini
Varadhan.
2) Simplify classifier state on sk_buff in order to shrink it a bit.
From Willem de Bruijn.
3) Introduce SIPHASH and it's usage for secure sequence numbers and
syncookies. From Jason A. Donenfeld.
4) Reduce CPU usage for ICMP replies we are going to limit or
suppress, from Jesper Dangaard Brouer.
5) Introduce Shared Memory Communications socket layer, from Ursula
Braun.
6) Add RACK loss detection and allow it to actually trigger fast
recovery instead of just assisting after other algorithms have
triggered it. From Yuchung Cheng.
7) Add xmit_more and BQL support to mvneta driver, from Simon Guinot.
8) skb_cow_data avoidance in esp4 and esp6, from Steffen Klassert.
9) Export MPLS packet stats via netlink, from Robert Shearman.
10) Significantly improve inet port bind conflict handling, especially
when an application is restarted and changes it's setting of
reuseport. From Josef Bacik.
11) Implement TX batching in vhost_net, from Jason Wang.
12) Extend the dummy device so that VF (virtual function) features,
such as configuration, can be more easily tested. From Phil
Sutter.
13) Avoid two atomic ops per page on x86 in bnx2x driver, from Eric
Dumazet.
14) Add new bpf MAP, implementing a longest prefix match trie. From
Daniel Mack.
15) Packet sample offloading support in mlxsw driver, from Yotam Gigi.
16) Add new aquantia driver, from David VomLehn.
17) Add bpf tracepoints, from Daniel Borkmann.
18) Add support for port mirroring to b53 and bcm_sf2 drivers, from
Florian Fainelli.
19) Remove custom busy polling in many drivers, it is done in the core
networking since 4.5 times. From Eric Dumazet.
20) Support XDP adjust_head in virtio_net, from John Fastabend.
21) Fix several major holes in neighbour entry confirmation, from
Julian Anastasov.
22) Add XDP support to bnxt_en driver, from Michael Chan.
23) VXLAN offloads for enic driver, from Govindarajulu Varadarajan.
24) Add IPVTAP driver (IP-VLAN based tap driver) from Sainath Grandhi.
25) Support GRO in IPSEC protocols, from Steffen Klassert"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1764 commits)
Revert "ath10k: Search SMBIOS for OEM board file extension"
net: socket: fix recvmmsg not returning error from sock_error
bnxt_en: use eth_hw_addr_random()
bpf: fix unlocking of jited image when module ronx not set
arch: add ARCH_HAS_SET_MEMORY config
net: napi_watchdog() can use napi_schedule_irqoff()
tcp: Revert "tcp: tcp_probe: use spin_lock_bh()"
net/hsr: use eth_hw_addr_random()
net: mvpp2: enable building on 64-bit platforms
net: mvpp2: switch to build_skb() in the RX path
net: mvpp2: simplify MVPP2_PRS_RI_* definitions
net: mvpp2: fix indentation of MVPP2_EXT_GLOBAL_CTRL_DEFAULT
net: mvpp2: remove unused register definitions
net: mvpp2: simplify mvpp2_bm_bufs_add()
net: mvpp2: drop useless fields in mvpp2_bm_pool and related code
net: mvpp2: remove unused 'tx_skb' field of 'struct mvpp2_tx_queue'
net: mvpp2: release reference to txq_cpu[] entry after unmapping
net: mvpp2: handle too large value in mvpp2_rx_time_coal_set()
net: mvpp2: handle too large value handling in mvpp2_rx_pkts_coal_set()
net: mvpp2: remove useless arguments in mvpp2_rx_{pkts, time}_coal_set
...
Create a helper function that decodes a xdr string object, allocates a memory
buffer and then store it as a NUL terminated string.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Pull audit updates from Paul Moore:
"The audit changes for v4.11 are relatively small compared to what we
did for v4.10, both in terms of size and impact.
- two patches from Steve tweak the formatting for some of the audit
records to make them more consistent with other audit records.
- three patches from Richard record the name of a module on module
load, fix the logging of sockaddr information when using
socketcall() on 32-bit systems, and add the ability to reset
audit's lost record counter.
- my lone patch just fixes an annoying style nit that I was reminded
about by one of Richard's patches.
All these patches pass our test suite"
* 'stable-4.11' of git://git.infradead.org/users/pcmoore/audit:
audit: remove unnecessary curly braces from switch/case statements
audit: log module name on init_module
audit: log 32-bit socketcalls
audit: add feature audit_lost reset
audit: Make AUDIT_ANOM_ABEND event normalized
audit: Make AUDIT_KERNEL event conform to the specification
Commit 34b88a68f2 ("net: Fix use after free in the recvmmsg exit path"),
changed the exit path of recvmmsg to always return the datagrams
variable and modified the error paths to set the variable to the error
code returned by recvmsg if necessary.
However in the case sock_error returned an error, the error code was
then ignored, and recvmmsg returned 0.
Change the error path of recvmmsg to correctly return the error code
of sock_error.
The bug was triggered by using recvmmsg on a CAN interface which was
not up. Linux 4.6 and later return 0 in this case while earlier
releases returned -ENETDOWN.
Fixes: 34b88a68f2 ("net: Fix use after free in the recvmmsg exit path")
Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
hrtimer handlers run with masked hard IRQ, we can therefore
use napi_schedule_irqoff()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e70ac17165.
jtcp_rcv_established() is in fact called with hard irq being disabled.
Initial bug report from Ricardo Nabinger Sanchez [1] still needs
to be investigated, but does not look like a TCP bug.
[1] https://www.spinics.net/lists/netdev/msg420960.html
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kernel test robot <xiaolong.ye@intel.com>
Cc: Ricardo Nabinger Sanchez <rnsanchez@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() to set a random MAC address in order to make sure
dev->addr_assign_type will be properly set to NET_ADDR_RANDOM.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trying to split and transmit a unicast packet in 16 parts will fail for
the final fragment: After having sent the 15th one with a frag_packet.no
index of 14, we will increase the the index to 15 - and return with an
error code immediately, even though one more fragment is due for
transmission and allowed.
Fixing this issue by moving the check before incrementing the index.
While at it, adding an unlikely(), because the check is actually more of
an assertion.
Fixes: ee75ed8887 ("batman-adv: Fragment and send skbs larger than mtu")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_frag_skb_buffer was supposed not to consume the skbuff
on errors. This was followed in the helper function
batadv_frag_insert_packet when the skb would potentially be inserted in the
fragment queue. But it could happen that the next helper function
batadv_frag_merge_packets would try to merge the fragments and fail. This
results in a kfree_skb of all the enqueued fragments (including the just
inserted one). batadv_recv_frag_packet would detect the error in
batadv_frag_skb_buffer and try to free the skb again.
The behavior of batadv_frag_skb_buffer (and its helper
batadv_frag_insert_packet) must therefore be changed to always consume the
skbuff to have a common behavior and avoid the double kfree_skb.
Fixes: 610bfc6bc9 ("batman-adv: Receive fragmented packets and merge")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The USEC_PER_SEC is used once in sock_set_timeout as the max value of
tv_usec. But there are other similar codes which use the literal
1000000 in this file.
It is minor cleanup to keep consitent.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skbs processed by ip_cmsg_recv() are not guaranteed to
be linear e.g. when sending UDP packets over loopback with
MSGMORE.
Using csum_partial() on [potentially] the whole skb len
is dangerous; instead be on the safe side and use skb_checksum().
Thanks to syzkaller team to detect the issue and provide the
reproducer.
v1 -> v2:
- move the variable declaration in a tighter scope
Fixes: ad6f939ab1 ("ip: Add offset parameter to ip_cmsg_recv")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is only one possible error path which reaches the err label, so
return ERR_PTR(-ENOMEM) directly if alloc_netdev_mqs() fails. This also
allows to omit the err variable.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
kstrtouint() can return a couple different error codes so the check for
"ret == -EINVAL" is wrong and static analysis tools correctly complain
that we can use "num" without initializing it. It's not super harmful
because we check the bounds. But it's also easy enough to fix.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Jozsef Kadlecsik says:
====================
ipset patches for nf
Please apply the next patches for ipset in your nf branch.
Both patches should go into the stable kernel branches as well,
because these are important bugfixes:
* Sometimes valid entries in hash:* types of sets were evicted
due to a typo in an index. The wrong evictions happen when
entries are deleted from the set and the bucket is shrinked.
Bug was reported by Eric Ewanco and the patch fixes
netfilter bugzilla id #1119.
* Fixing of a null pointer exception when someone wants to add an
entry to an empty list type of set and specifies an add before/after
option. The fix is from Vishwanath Pai.
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Otherwise, different subsys will race to access the err_list, with holding
the different nfnl_lock(subsys_id).
But this will not happen now, since ->call_batch is only implemented by
nftables, so the err_list is protected by nfnl_lock(NFNL_SUBSYS_NFTABLES).
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- Implement wraparound-safe refcount_t and kref_t types based on
generic atomic primitives (Peter Zijlstra)
- Improve and fix the ww_mutex code (Nicolai Hähnle)
- Add self-tests to the ww_mutex code (Chris Wilson)
- Optimize percpu-rwsems with the 'rcuwait' mechanism (Davidlohr
Bueso)
- Micro-optimize the current-task logic all around the core kernel
(Davidlohr Bueso)
- Tidy up after recent optimizations: remove stale code and APIs,
clean up the code (Waiman Long)
- ... plus misc fixes, updates and cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (50 commits)
fork: Fix task_struct alignment
locking/spinlock/debug: Remove spinlock lockup detection code
lockdep: Fix incorrect condition to print bug msgs for MAX_LOCKDEP_CHAIN_HLOCKS
lkdtm: Convert to refcount_t testing
kref: Implement 'struct kref' using refcount_t
refcount_t: Introduce a special purpose refcount type
sched/wake_q: Clarify queue reinit comment
sched/wait, rcuwait: Fix typo in comment
locking/mutex: Fix lockdep_assert_held() fail
locking/rtmutex: Flip unlikely() branch to likely() in __rt_mutex_slowlock()
locking/rwsem: Reinit wake_q after use
locking/rwsem: Remove unnecessary atomic_long_t casts
jump_labels: Move header guard #endif down where it belongs
locking/atomic, kref: Implement kref_put_lock()
locking/ww_mutex: Turn off __must_check for now
locking/atomic, kref: Avoid more abuse
locking/atomic, kref: Use kref_get_unless_zero() more
locking/atomic, kref: Kill kref_sub()
locking/atomic, kref: Add kref_read()
locking/atomic, kref: Add KREF_INIT()
...
Johan Hedberg says:
====================
pull request: bluetooth-next 2017-02-19
Here's a set of Bluetooth patches for the 4.11 kernel:
- New USB IDs to the btusb driver
- Race fix in btmrvl driver
- Added out-of-band wakeup support to the btusb driver
- NULL dereference fix to bt_sock_recvmsg
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netconf support to MPLS. Allows userpsace to learn and be notified
of changes to 'input' enable setting per interface.
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add support for MSG_MORE on sctp.
It adds force_delay in sctp_datamsg to save MSG_MORE, and sets it after
creating datamsg according to the send flag. sctp_packet_can_append_data
then uses it to decide if the chunks of this msg will be sent at once or
delay it.
Note that unlike [1], this patch saves MSG_MORE in datamsg, instead of
in assoc. As sctp enqueues the chunks first, then dequeue them one by
one. If it's saved in assoc,the current msg's send flag (MSG_MORE) may
affect other chunks' bundling.
Since last patch, sctp flush out queue once assoc state falls into
SHUTDOWN_PENDING, the close block problem mentioned in [1] has been
solved as well.
[1] https://patchwork.ozlabs.org/patch/372404/
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to flush out queue when assoc state falls into
SHUTDOWN_PENDING if there are still chunks in it, so that the
data can be sent out as soon as possible before sending SHUTDOWN
chunk.
When sctp supports MSG_MORE flag in next patch, this improvement
can also solve the problem that the chunks with MSG_MORE flag
may be stuck in queue when closing an assoc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Connlabels are included in conntrack netlink event messages only if
the IPCT_LABEL bit is set in the event cache (see
ctnetlink_conntrack_event()). Set it after initializing labels for a
new connection.
Found upon further system testing, where it was noticed that labels
were missing from the conntrack events.
Fixes: 193e309678 ("openvswitch: Do not trigger events for unconfirmed connections.")
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To spare checking for "this reply fits into a page, but does it fit
into my buffer?" in some callers, osd_req_op_cls_response_data_pages()
needs to know how big it is.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
With EC overwrites maturing, the kernel client will be getting exposed
to potentially very wide EC pools. While "min(pi->size, X)" works fine
when the cluster is stable and happy, truncating OSD sets interferes
with resend logic (ceph_is_new_interval(), etc). Abort the mapping if
the pool is too wide, assigning the request to the homeless session.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Much like Arlo Guthrie, I decided that one big pile is better than two
little piles.
Reflects ceph.git commit 95c2df6c7e0b22d2ea9d91db500cf8b9441c73ba.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Then add it to the working state. It would be very nice if we didn't
have to take a lock to calculate a crush placement. By moving the
permutation array into the working data, we can treat the CRUSH map as
immutable.
Reflects ceph.git commit cbcd039651c0569551cb90d26ce27e1432671f2a.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
This was causing a build failure for openrisc when using musl and
gcc 5.4.0 since the file is not available in the toolchain.
It doesnt seem this is needed and removing it does not cause any build
warnings for me.
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
add_to_page_cache_lru() can fails, so the actual pages to read
can be smaller than the initial size of osd request. We need to
update osd request size in that case.
Signed-off-by: Yan, Zheng <zyan@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Currently crypto.c gets linux/sched.h indirectly through linux/slab.h
from linux/kasan.h. Include it directly for memalloc_noio_*() inlines.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
sctp has changed to use rhlist for transport rhashtable since commit
7fda702f93 ("sctp: use new rhlist interface on sctp transport
rhashtable").
But rhltable_insert_key doesn't check the duplicate node when inserting
a node, unlike rhashtable_lookup_insert_key. It may cause duplicate
assoc/transport in rhashtable. like:
client (addr A, B) server (addr X, Y)
connect to X INIT (1)
------------>
connect to Y INIT (2)
------------>
INIT_ACK (1)
<------------
INIT_ACK (2)
<------------
After sending INIT (2), one transport will be created and hashed into
rhashtable. But when receiving INIT_ACK (1) and processing the address
params, another transport will be created and hashed into rhashtable
with the same addr Y and EP as the last transport. This will confuse
the assoc/transport's lookup.
This patch is to fix it by returning err if any duplicate node exists
before inserting it.
Fixes: 7fda702f93 ("sctp: use new rhlist interface on sctp transport rhashtable")
Reported-by: Fabio M. Di Nitto <fdinitto@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add reconf chunk event based on the sctp event
frame in rx path, it will call sctp_sf_do_reconf to process the
reconf chunk.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add a function to process the incoming reconf chunk,
in which it verifies the chunk, and traverses the param and process
it with the right function one by one.
sctp_sf_do_reconf would be the process function of reconf chunk event.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add a function sctp_verify_reconf to do some length
check and multi-params check for sctp stream reconf according to rfc6525
section 3.1.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to implement Receiver-Side Procedures for the Incoming
SSN Reset Request Parameter described in rfc6525 section 5.2.3.
It's also to move str_list endian conversion out of sctp_make_strreset_req,
so that sctp_make_strreset_req can be used more conveniently to process
inreq.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to implement Receiver-Side Procedures for the Outgoing
SSN Reset Request Parameter described in rfc6525 section 5.2.2.
Note that some checks must be after request_seq check, as even those
checks fail, strreset_inseq still has to be increase by 1.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add Stream Reset Event described in rfc6525
section 6.1.1.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to define Re-configuration Response Parameter described
in rfc6525 section 4.4. As optional fields are only for SSN/TSN Reset
Request Parameter, it uses another function to make that.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Diving the divider by the multiplier before applying to the input.
When this would "divide by zero", divide the multiplier by the divider
first then multiply the input by this value.
Currently user2creds outputs zero when input value is bigger than the
number of slices and lower than scale.
This as then user input is applied an integer divide operation to
a number greater than itself (scale).
That rounds up to zero, then we multiply zero by the credits slice size.
iptables -t filter -I INPUT --protocol tcp --match hashlimit
--hashlimit 40/second --hashlimit-burst 20 --hashlimit-mode srcip
--hashlimit-name syn-flood --jump RETURN
thus trigger the overflow detection code:
xt_hashlimit: overflow, try lower: 25000/20
(25000 as hashlimit avg and 20 the burst)
Here:
134217 slices of (HZ * CREDITS_PER_JIFFY) size.
500000 is user input value
1000000 is XT_HASHLIMIT_SCALE_v2
gives: 0 as user2creds output
Setting burst to "1" typically solve the issue ...
but setting it to "40" does too !
This is on 32bit arch calling into revision 2 of hashlimit.
Signed-off-by: Alban Browaeys <alban.browaeys@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Yotam Gigi