Without this patch Forward and Backward buttons on the touchpad do not
generate any events.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_PC is left-over cruft after the introduction of CONFIG_X86_PC with
the subarch split. Remove it, and fixup the remaining users to depend on
CONFIG_X86_PC instead.
Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update drivers to new input layer changes.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Reorder code in gscps2_interrupt() and only enable ports when opened.
This fixes issues with hangs booting an SMP kernel on my C360.
Previously serio_interrupt() could be called before the lock in
struct serio was initialised.
Signed-off-by: Richard Hirst <rhirst@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This patch converts kcalloc(1, ...) calls to use the new kzalloc() function.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rearrange attribute code to use generic show and set handlers
instead of replicating them for every attribute; switch to
using attribute_group instead of creating all attributes
manually. All this saves about 4K.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Synaptics driver used child->type to select either 3-byte or 4-byte
packet size for the pass-through port; this gives wrong results for
the newer protocols. Change the check to use child->pktsize instead.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are wheel mice that respond to Logitech probes and report
that they have only 2 buttons (such as e-Aser mouse) and this
stops the wheel from being used as a middle button. Change the
driver to always report BTN_MIDDLE capability if a wheel is
present.
Also, never reset BTN_RIGHT capability in logips2pp code - there
are no Logitech mice that have only one button and if some other
mice happen to respond to Logitech's query we could do the wrong
thing.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The condition in alps_init() was also inverted and the driver
was enabling tapping mode only if it was already enabled.
Signed-off-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The driver would not reset pass-through mode when performing
resume of a DualPoint touchpad causing it to stop working
until next reboot.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It looks like logic for enabling hardware tapping in ALPS driver was
inverted and we enable it only if it was already enabled by BIOS or
firmware.
I have a confirmation from one user that the patch below fixes the problem
for him and it might be beneficial if we could get it into 2.6.12.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
given number of bytes from device. Change ps2_command to
allow using 0 as command ID and actually pass it to the
device instead of working as a drain.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
operations do not iterfere with each other.
Also make sure that serio core takes serio->drv_sem
not only for connect/disconnect but for reconnect
too.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
I have an Ahtec laptop with a ALPS GlidePoint device, with 4 buttons.
With Linux hernel 2.6.12rc4 and rc5 I'm unable to use the vertical
scroll buttons (BACK and FORWARD).
BACK gets detected as BTN_MIDDLE and FORWARD is undetected.
I've modified the drivers/input/mouse/alps.c from 2.6.12rc5 and now it
works fine!
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- do not try to set rate and resolution in init method, let
psmouse core do it for us. This also removes special quirks
from the core;
- do not disable mouse before doing full reset - meaningless;
- some formatting and whitespace cleanups.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
sends an incorrect ID and wasn't recognized.
Reported-by: Stefan Seyfried <seife@suse.de>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
ALPS needs to be reset for detection to work reliably when reconnecting.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Larry Finger