CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: uclinux-dist-devel@blackfin.uclinux.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings recently came up with a better way to handle the kconfig
dependencies for the PTP hardware clocks. This patch converts one new and
one older driver to the new scheme.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BF518 has a PTP time unit that works in a similar way to other MAC
based clocks, like gianfar, ixp46x, and igb. This patch adds support for
using the blackfin as a PHC. Although the blackfin hardware does offer a
few ancillary features, this patch implements only the basic operations.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the sys time stamps and timecompare code with simple
raw hardware time stamps in nanosecond resolution. The only tricky bit is
to find a PTP Hardware Clock period slower than the input clock period
and a power of two.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware time stamping code is a compile time option for the blackfin.
When it is not enabled, the driver should fall back to the standard
ethtool reply to the get_ts_info query.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt adi ethernet driver to changes in bfin_get_ether_addr()
from arch/blackfin. bfin_get_ether_addr() returns now a state.
Set a random mac address via new eth_hw_addr_random() in case
the return value is not 0.
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
v2: change the logic to reduce unneeded checks
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
- Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MII Kconfig option is apart of the core networking drivers and
by default NET_CORE is enabled so drivers selecting MII will
have MII enabled as well. It was found using the randconfig
option during testing, MII would be selected but NET_CORE
could be disabled. This caused a dependency error.
Resolved the dependency by selecting NET_CORE when MII is
selected.
Reported-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the Analog Devices Inc driver into drivers/net/ethernet/adi/ and
make the necessary Kconfig and Makefile changes.
CC: <uclinux-dist-devel@blackfin.uclinux.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Bob Liu <bob.liu@analog.com>
Bill Pemberton