Passing the encoder to the TCON RGB setup functions allows accessing the
connector from the encoder directly instead of relying on the panel.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107181843.27628-2-contact@paulk.fr
Some SoCs, such as H6, doesn't have a full-featured TCON TOP.
Add quirks support for TCON TOP.
Currently the presence of TCON_TV1 and DSI is controlled via the quirks
structure.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[Fixed code style and removed unnecessary initialization]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-25-jernej.skrabec@siol.net
It turns out that TCON TOP registers in H6 SoC have non-zero reset
value. This may cause issues if bits are not changed during
configuration.
To prevent that, initialize registers to 0.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-24-jernej.skrabec@siol.net
H6 has Synopsys DWC HDMI 2.0 TX PHY.
There is no freely available documentation for it, only code found in
BSP kernel. However, judging by the code, PHY is very similar to older
Synopsys HDMI PHY described in i.MX6 documentation. Most registers seem
to be the same.
According to i.MX6 documentation, mpll settings are based on pixel clock
and are not specific to each SoC. Because of that, mpll table in this
commit is based on that documentation and not on BSP code. Other PHY
settings were derived from BSP PHY driver code.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-23-jernej.skrabec@siol.net
Currently sun8i-hdmi-phy driver supports only custom PHYs connected to
DW HDMI controller. Since newest Allwinner SoCs have unmodified Synopsys
PHY, driver has to be reorganized to support them.
Variant structure is expanded to allow differentiation between custom
and Sysnopsys PHYs and to hold Synopsys PHY settings.
Since DW HDMI bridge platform data has different fields for custom and
Sysnopsys PHY, function sun8i_hdmi_phy_get_ops() is replaced with
sun8i_hdmi_phy_set_ops().
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-22-jernej.skrabec@siol.net
Currently, quirks and compatibles are sorted alphabetically. However,
they should be sorted by family release date and then alphabetically.
Fix that by moving A64 quirks and compatible to bottom. No functional
change is made.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-21-jernej.skrabec@siol.net
It turns out that H6 HDMI BSP kernel driver doesn't change TMDS rate at
all. At this point it is not clear whether it is just not necessary or
it would cause some kind of issues.
Add a quirk for it.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-18-jernej.skrabec@siol.net
Since it is not possible to access sun8i-dw-hdmi driver private data
inside mode_valid function, make it configurable. That way different
versions of HDMI controllers can set different function, depending on
it's limitations.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-17-jernej.skrabec@siol.net
Currently supported Allwinner SoCs with DW HDMI controller have
scrambled addresses and read lock. However, that is not true in general.
For example, A80 and H6 have normal addresses and normal read access.
Move code for unscrambling addresses and unlocking read access to it's
own function and call it from init function.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-16-jernej.skrabec@siol.net
Mixer 0 has 1 VI and 3 UI planes, scaler on all planes and can output
4K image @60Hz. It also support 10 bit colors, which are not yet
implemented.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-14-jernej.skrabec@siol.net
Display Engine 3 is an upgrade of DE2 with new features like support for
10 bit color formats and support for AFBC.
Most of DE2 code works with DE3, except some small details.
Implement basic support for DE3. Support for 10 bit colort formats and
AFBC, among others missing features, will be added later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/260238/
Most, if not all, registers found in DE2 still exists in DE3. However,
units are on different base addresses.
To prepare for addition of DE3 support, registers macros are reworked so
they take base address as parameter.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[rebased]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-10-jernej.skrabec@siol.net
The CMA helper is already using the drm_fb_helper_generic_probe part of
the generic fbdev emulation. This patch makes full use of the generic
fbdev emulation by using its drm_client callbacks. This means that
drm_mode_config_funcs->output_poll_changed and drm_driver->lastclose are
now handled by the emulation code. Additionally fbdev unregister happens
automatically on drm_dev_unregister().
The drm_fbdev_generic_setup() call is put after drm_dev_register() in the
driver. This is done to highlight the fact that fbdev emulation is an
internal client that makes use of the driver, it is not part of the
driver as such. If fbdev setup fails, an error is printed, but the driver
succeeds probing.
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025201340.34227-8-noralf@tronnes.org
The is_double flag is a boolean currently assigned to the value of the d
variable, that is either 1 or 2. It means that this is_double variable is
always set to true, even though the initial intent was to have it set to
true when d is 2.
Fix this.
Fixes: 9c5681011a ("drm/sun4i: Add HDMI support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181021163446.29135-2-maxime.ripard@bootlin.com
The is_double variable is used to store, and possibly returning to the
calling function, whether it needs to double the rate of the parent clock
or not.
In the case where it does, the variable is affected, but in the case where
it doesn't we return some uninitialized value. Fix this.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181021163446.29135-1-maxime.ripard@bootlin.com
-----BEGIN PGP SIGNATURE-----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=3yxi
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-10-24' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This is going to rebuild more than drm as it adds a new helper to
list.h for doing bulk updates. Seemed like a reasonable addition to
me.
Otherwise the usual merge window stuff lots of i915 and amdgpu, not so
much nouveau, and piles of everything else.
Core:
- Adds a new list.h helper for doing bulk list updates for TTM.
- Don't leak fb address in smem_start to userspace (comes with EXPORT
workaround for people using mali out of tree hacks)
- udmabuf device to turn memfd regions into dma-buf
- Per-plane blend mode property
- ref/unref replacements with get/put
- fbdev conflicting framebuffers code cleaned up
- host-endian format variants
- panel orientation quirk for Acer One 10
bridge:
- TI SN65DSI86 chip support
vkms:
- GEM support.
- Cursor support
amdgpu:
- Merge amdkfd and amdgpu into one module
- CEC over DP AUX support
- Picasso APU support + VCN dynamic powergating
- Raven2 APU support
- Vega20 enablement + kfd support
- ACP powergating improvements
- ABGR/XBGR display support
- VCN jpeg support
- xGMI support
- DC i2c/aux cleanup
- Ycbcr 4:2:0 support
- GPUVM improvements
- Powerplay and powerplay endian fixes
- Display underflow fixes
vmwgfx:
- Move vmwgfx specific TTM code to vmwgfx
- Split out vmwgfx buffer/resource validation code
- Atomic operation rework
bochs:
- use more helpers
- format/byteorder improvements
qxl:
- use more helpers
i915:
- GGTT coherency getparam
- Turn off resource streamer API
- More Icelake enablement + DMC firmware
- Full PPGTT for Ivybridge, Haswell and Valleyview
- DDB distribution based on resolution
- Limited range DP display support
nouveau:
- CEC over DP AUX support
- Initial HDMI 2.0 support
virtio-gpu:
- vmap support for PRIME objects
tegra:
- Initial Tegra194 support
- DMA/IOMMU integration fixes
msm:
- a6xx perf improvements + clock prefix
- GPU preemption optimisations
- a6xx devfreq support
- cursor support
rockchip:
- PX30 support
- rgb output interface support
mediatek:
- HDMI output support on mt2701 and mt7623
rcar-du:
- Interlaced modes on Gen3
- LVDS on R8A77980
- D3 and E3 SoC support
hisilicon:
- misc fixes
mxsfb:
- runtime pm support
sun4i:
- R40 TCON support
- Allwinner A64 support
- R40 HDMI support
omapdrm:
- Driver rework changing display pipeline ordering to use common code
- DMM memory barrier and irq fixes
- Errata workarounds
exynos:
- out-bridge support for LVDS bridge driver
- Samsung 16x16 tiled format support
- Plane alpha and pixel blend mode support
tilcdc:
- suspend/resume update
mali-dp:
- misc updates"
* tag 'drm-next-2018-10-24' of git://anongit.freedesktop.org/drm/drm: (1382 commits)
firmware/dmc/icl: Add missing MODULE_FIRMWARE() for Icelake.
drm/i915/icl: Fix signal_levels
drm/i915/icl: Fix DDI/TC port clk_off bits
drm/i915/icl: create function to identify combophy port
drm/i915/gen9+: Fix initial readout for Y tiled framebuffers
drm/i915: Large page offsets for pread/pwrite
drm/i915/selftests: Disable shrinker across mmap-exhaustion
drm/i915/dp: Link train Fallback on eDP only if fallback link BW can fit panel's native mode
drm/i915: Fix intel_dp_mst_best_encoder()
drm/i915: Skip vcpi allocation for MSTB ports that are gone
drm/i915: Don't unset intel_connector->mst_port
drm/i915: Only reset seqno if actually idle
drm/i915: Use the correct crtc when sanitizing plane mapping
drm/i915: Restore vblank interrupts earlier
drm/i915: Check fb stride against plane max stride
drm/amdgpu/vcn:Fix uninitialized symbol error
drm: panel-orientation-quirks: Add quirk for Acer One 10 (S1003)
drm/amd/amdgpu: Fix debugfs error handling
drm/amdgpu: Update gc_9_0 golden settings.
drm/amd/powerplay: update PPtable with DC BTC and Tvr SocLimit fields
...
The calculated ideal rate can easily overflow an unsigned long, thus
making the best div selection buggy as soon as no ideal match is found
before the overflow occurs.
Fixes: 4731a72df2 ("drm/sun4i: request exact rates to our parents")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181018100250.12565-1-boris.brezillon@bootlin.com
If tcon->panel pointer is NULL, trying to dereference from it
(i.e. tcon->panel->connector) will cause a null pointer dereference.
Add tcon->panel null pointer check before calling
sun4i_tcon0_mode_set_dithering().
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Fixes: f11adcecbd ("drm/sun4i: tcon: Add dithering support for
RGB565/RGB666 LCD panels")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005215951.99003-2-giulio.benetti@micronovasrl.com
Since tcon->panel is a pointer returned by of_drm_find_panel() need to
check if it is not NULL, hence a valid pointer.
IS_ERR() instead checks return error values, not NULL pointers.
Substitute "if (!IS_ERR(tcon->panel))" with "if (tcon->panel)".
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181005215951.99003-1-giulio.benetti@micronovasrl.com
This reverts commit 3510e7a7f9.
During the 4.19 merge window for drm-misc, two patches critical to
supporting the display pipeline on the Allwinner R40 SoC were missed.
They were applied later but missed the merge window deadline. As a
result 4.19-rc1 kernel would crash on the R40 when it couldn't parse
the new device tree structure. We ended up removing support for the
R40 display pipeline for 4.19.
Since the missing patches are already merged for 4.20, we can now
revert the commit that removed support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180921142743.8711-1-wens@csie.org
The A64 HDMI PHY seems to be not able to use the second video PLL as
clock parent in experiments.
Drop the support for the second PLL from A64 HDMI PHY driver.
Fixes: b46e2c9f5f ("drm/sun4i: Add support for A64 HDMI PHY")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180916043409.62374-2-icenowy@aosc.io
Having DRM_SUN4I built-in but DRM_SUN8I_MIXER as a loadable module results in
a link error, as we try to access a symbol from the sun8i_tcon_top.ko module:
ERROR: "sun8i_tcon_top_de_config" [drivers/gpu/drm/sun4i/sun4i-tcon.ko] undefined!
ERROR: "sun8i_tcon_top_set_hdmi_src" [drivers/gpu/drm/sun4i/sun4i-tcon.ko] undefined!
ERROR: "sun8i_tcon_top_of_table" [drivers/gpu/drm/sun4i/sun4i-tcon.ko] undefined!
This solves the problem by adding a silent symbol for the tcon_top module,
building it as a separate module in exactly the cases that we need it,
but in a way that it is reachable by the other modules.
Fixes: cf77d79b4e ("drm/sun4i: tcon: Add another way for matching mixers with tcon")
Fixes: 0305189afb ("drm/sun4i: tcon: Add support for R40 TCON")
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Matt Hart <matthew.hart@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180911113325.11024-1-maxime.ripard@bootlin.com
Two patches from the R40 display pipeline support series weren't applied
with the rest of the series. When they did get applied, the -rc6
deadline for drm-misc-next had past, so they didn't get into 4.19-rc1
with the rest of the series. However, the two patches are crucial in
the parsing of the R40's display pipeline graph in the device tree.
Without them, the driver crashes because it can't follow the odd graph
structure.
This patch removes the R40 compatibles from the sun4i-drm driver,
effectively disabling DRM support for the R40 for one release cycle.
This will prevent the driver from crashing upon probing.
The compatibles should be reinstated for the next release.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180827083950.602-1-wens@csie.org
Signed-off-by: Sean Paul <seanpaul@chromium.org>
The hardware supports dithering on TCON channel 0 which is used for LCD
panels.
Dithering is a method of approximating a color from a mixture of other
colors when the required color isn't available. It reduces color
banding artifacts that can be observed when displaying gradients
(e.g. grayscale gradients). This may occur when the image that needs
to be displayed is 24-bit but the LCD panel is a lower bit depth and
does not perform dithering on its own.
Signed-off-by: Jonathan Liu <net147@gmail.com>
[wens@csie.org: check display_info.bpc first; handle LVDS and MIPI DSI]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180907041948.19913-4-wens@csie.org
Dithering is only supported for TCON channel 0. Throughout the datasheet
all the names associated with these register are prefixed "TCON0",
instead of "TCON". The only exception is the control register
"TCON_FRM_CTL_REG".
Rename the macros to reflect this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180907041948.19913-3-wens@csie.org
sun4i_tcon0_mode_set_cpu() currently accepts struct mipi_dsi_device *
as its second parameter. This is derived from drm_encoder.
The DSI encoder is tied to the CPU interface mode of the TCON as a
special case. In theory, if hardware were available, we could also
support normal CPU interface modes. It is better to pass the generic
encoder instead of the specialized mipi_dsi_device, and handle the
differences inside the function.
Passing the encoder would also enable the function to pass it, or any
other data structures related to it, to other functions expecting it.
One such example would be dithering support that will be added in a
later patch, which looks at properties tied to the connector to
determine whether dithering should be enabled or not.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180907041948.19913-2-wens@csie.org
Some boards have HDMI VCC pin connected to voltage regulator which may
not be turned on by default.
Add support for such boards by adding voltage regulator handling code to
HDMI driver.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[Icenowy: change supply name to "hvcc"]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904044053.15425-11-icenowy@aosc.io
Display Engine(DE2) in Allwinner A64 has two mixers and tcons.
The routing for mixer0 is through tcon0 and connected to
LVDS/RGB/MIPI-DSI controller.
The routing for mixer1 is through tcon1 and connected to HDMI.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904044053.15425-6-icenowy@aosc.io
Mixers in Allwinner have similar capabilities as others SoCs with DE2.
Add support for them.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Icenowy: Add mixer1]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904044053.15425-5-icenowy@aosc.io
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This issue was detected with the help of Coccinelle.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180824010521.GA25451@embeddedor.com
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
A new helper function(__drm_atomic_helper_plane_reset) has been added
for linking a plane with its state and resetting the core
properties(alpha, rotation, etc.) to their default values.
Use that instead of duplicating the logic.
__drm_atomic_helper_plane_reset initializes the alpha property to its
max value, which is defined by the drm core as DRM_BLEND_ALPHA_OPAQUE,
so nothing changes regarding the alpha value.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180804161530.12275-9-alexandru-cosmin.gheorghe@arm.com
R40 TV TCON is basically the same as on A83T. However, it needs special
handling, because it has to set up TCON TOP muxes at runtime.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710203511.18454-14-jernej.skrabec@siol.net
Till now, new way of matching engines with TCONs was reading their
respective ids and match them by those ids. However, with introduction
of TCON TOP, that might not be so straightforward anymore.
- there might be more TCONs that engines (mixers)
- TCON ids might have non-consecutive ids
Workaround that by matching mixer id with TCON index from TCON list.
For example, R40 has 2 mixers and 4 TCONs. Board designer can choose
2 outputs, which are connected to any of those 4 TCONs. As long as there
are only 2 TCONs enabled in DT, using index in list as alternative id,
will allow to match them with mixer 0 and 1.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710203511.18454-13-jernej.skrabec@siol.net
Not all sunxi platforms with the first version of the Display Engine
support an alpha component on the plane with the lowest z position
(as in: lowest z-pos), that gets blended with the background color.
In particular, the A13 is known to have this limitation. However, it was
recently discovered that the A20 and A33 are capable of having alpha on
their lowest plane.
Thus, this introduces a specific quirk to indicate such support,
per-platform. Since this was not tested on sun4i and sun6i platforms, a
conservative approach is kept and this feature is not supported.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180719080838.31598-2-paul.kocialkowski@bootlin.com
In prevision for introducing a new quirk that will be used at atomic
plane check time, register the quirks structure with the backend
structure. This way, it can easily be grabbed where needed.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180719080838.31598-1-paul.kocialkowski@bootlin.com
Handle both positive and negative dclk polarity,
according to bus_flags, taking care of this:
On A20 and similar SoCs, the only way to achieve Positive Edge
(Rising Edge), is setting dclk clock phase to 2/3(240°).
By default TCON works in Negative Edge(Falling Edge), this is why phase
is set to 0 in that case.
Unfortunately there's no way to logically invert dclk through IO_POL
register.
The only acceptable way to work, triple checked with scope,
is using clock phase set to 0° for Negative Edge and set to 240° for
Positive Edge.
On A33 and similar SoCs there would be a 90° phase option, but it divides
also dclk by 2.
This patch is a way to avoid quirks all around TCON and DOTCLOCK drivers
for using A33 90° phase divided by 2 and consequently increase code
complexity.
Check if panel is used. TCON can also handle VGA DAC, then panel could
be empty.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180718142357.120998-1-giulio.benetti@micronovasrl.com
Blending order is set based on the z position of each DRM plane. The
blending order register is currently cleared at each atomic DRM commit,
with the intent that each committed plane will set the appropriate
bits (based on its z-pos) when enabling the plane.
However, it sometimes happens that a particular plane is left unchanged
by an atomic commit and thus will not be configured again. In that
scenario, blending order is cleared and only the bits relevant for the
planes affected by the commit are set. This leaves the planes that did
not change without their blending order set in the register, leading
to that plane not being displayed.
Instead of clearing the blending order register at every atomic commit,
this change moves the register's initial clear at bind time and only
clears the bits for a specific plane when disabling it or changing its
zpos.
This way, planes that are left untouched by a DRM atomic commit are
no longer disabled.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180717122522.11327-1-paul.kocialkowski@bootlin.com
This patch unifies the naming of DRM functions for reference counting
of struct drm_device. The resulting code is more aligned with the rest
of the Linux kernel interfaces.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180717084814.18091-1-tzimmermann@suse.de
When commit af11942ee4 ("drm/sun4i: tcon-top: Cleanup clock handling")
was merged, the error handling path of the of_property_match_string was
changed to take into account the fact that the returned value of that
function wasn't an error pointer but an error code.
Unfortunately, this introduced a warning since the now returned value is an
integer, while the sun8i_tcon_top_register_gate function should return an
error pointer.
Fix that by calling ERR_PTR.
Cc: Jernej Skrabec <jernej.skrabec@siol.net>
Cc: Chen-Yu Tsai <wens@csie.org>
Fixes: af11942ee4 ("drm/sun4i: tcon-top: Cleanup clock handling")
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712080818.3571-1-maxime.ripard@bootlin.com
Initial implementation of DE2 planes only supported fixed zpos.
Expand implementation with configurable zpos property.
Implementation background:
Channel in DE2 driver represents one DRM plane, whereas pipe is just
mapped channel to known Z position. Pipe 0 will always be at the bottom,
pipe 1 just above pipe 0 and so on. If, for example, channel 1 is mapped
at pipe 0 and channel 0 at pipe 1, whatever is on channel 0 will appear
on top.
Before this commit, channel id was used for addressing channel related
registers (prefixed with SUN8I_MIXER_CHAN_UI_ or SUN8I_MIXER_CHAN_VI_)
and pipe registers (prefixed with SUN8I_MIXER_BLEND_). Additionally,
register SUN8I_MIXER_BLEND_ROUTE, which takes care for mapping channels
to pipes had fixed value. It mapped channel 0 to pipe 0, 1 to 1 and so
on. Consequence of all that was fixed Z order of planes.
With this commit, pipe registers are using zpos property as index and
channel related registers still use channel id as index. Pipe mapping
register is now set dynamically too and pipe enable register is rebuild
every time to make sure only active pipes are enabled.
Testing was done to confirm that there is no issues if bottom plane
contains pixels with alpha value < 0xff and if it doesn't whole screen.
Tested-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706164732.24166-1-jernej.skrabec@siol.net
Having DRM_SUN4I built-in but DRM_SUN8I_MIXER as a loadable module results in
a link error, as we try to access a symbol from the sun8i_tcon_top.ko module:
ERROR: "sun8i_tcon_top_of_table" [drivers/gpu/drm/sun4i/sun8i-drm-hdmi.ko] undefined!
ERROR: "sun8i_tcon_top_of_table" [drivers/gpu/drm/sun4i/sun4i-drm.ko] undefined!
This solves the problem by adding a silent symbol for the tcon_top module,
building it as a separate module in exactly the cases that we need it,
but in a way that it is reachable by the other modules.
Fixes: 57e23de02f ("drm/sun4i: DW HDMI: Expand algorithm for possible crtcs")
Fixes: ef0cf6441f ("drm/sun4i: Add support for traversing graph with TCON TOP")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180711144403.1022829-1-arnd@arndb.de
Currently, TCON supports 2 ways to match TCON with engine (mixer in this
case). Old way is to just traverse of graph backwards and compare node
pointer. New way is to match TCON and engine by their respective ids.
All SoCs with DE2 enabled till now used the old way, which means mixer
id was never used and thus never implemented.
However, for R40, only the new way will be used. To prepare for that,
implement mixer id fetching from DT.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180711112706.30222-1-jernej.skrabec@siol.net
We want to be able to set TCON TOP muxes at runtime. Add helpers for
that.
Old, static configuration of muxes at probe time is preserved for now.
It will be removed when R40 TCON starts using them.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710203511.18454-12-jernej.skrabec@siol.net
If error happens in sun8i_dw_hdmi_find_possible_crtcs(), nodes are not
released with of_node_put() before returning.
Fix that by calling of_node_put() when necessary. While on it, clean up
the code by using of_graph_get_remote_node() which also lowers number of
cases where error handling has to be performed.
Fixes: 57e23de02f ("drm/sun4i: DW HDMI: Expand algorithm for possible crtcs")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710203511.18454-8-jernej.skrabec@siol.net
Function sun4i_tcon_find_engine_traverse() doesn't release node if it
needs to traverse of graph deeper than 1 level.
Fix this by calling of_node_put().
Fixes: 49836b11fe ("drm/sun4i: tcon: Generalize engine search algorithm")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710203511.18454-6-jernej.skrabec@siol.net
There is no need to acquire reference to clock just to get its name.
This commit just cleans up the code. There is no functional change.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[Maxime: Fixed the of_property_match_string error check]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710203511.18454-5-jernej.skrabec@siol.net
Right now, the DRM panel logic returns NULL when a panel pointing to
the passed OF node is not present in the list of registered panels.
Most drivers interpret this NULL value as -EPROBE_DEFER, but we are
about to modify the semantic of of_drm_find_panel() and let the
framework return -ENODEV when the device node we're pointing to has
a status property that is not equal to "okay" or "ok".
Let's first patch the of_drm_find_panel() implementation to return
ERR_PTR(-EPROBE_DEFER) instead of NULL and patch all callers to replace
the '!panel' check by an 'IS_ERR(panel)' one.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180509130042.9435-2-boris.brezillon@bootlin.com
When the base sun4i DRM driver is built-in but the back-end is
a loadable module, we run into a link error:
drivers/gpu/drm/sun4i/sun4i_drv.o: In function `sun4i_drv_probe':
sun4i_drv.c:(.text+0x60c): undefined reference to `sun4i_frontend_of_table'
The dependency is a bit tricky, the best workaround I have come up
with is to use a Makefile hack to to interpret both
CONFIG_DRM_SUN4I_BACKEND=m and CONFIG_DRM_SUN4I_BACKEND=y
as a directive to build the front-end the same way as the main module.
Fixes: dd0421f475 ("drm/sun4i: Add a driver for the display frontend")
Link: https://lore.kernel.org/lkml/20180301091908.zcptz3ezqr2c6ly5@flea/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180706142847.2032381-1-arnd@arndb.de
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm_of_find_possible_crtcs() doesn't work when DW HDMI encoder is
connected to TCON (crtc) through mux in TCON TOP.
In that case TCON TOP HDMI mux input port has to be manually traversed
and checked if it matches any known crtc.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-23-jernej.skrabec@siol.net
DW HDMI PHY driver and PHY clock driver share same registers. Make sure
that DW HDMI PHY setup code doesn't change any clock related bits.
During initialization, set PHY PLL parent bit to 0.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-18-jernej.skrabec@siol.net
Current DW HDMI PHY code never prepares and enables PHY clock after it is
created. It's just used as it is. This may work in some cases, but it's
clearly wrong. Fix it by adding proper calls to enable/disable PHY
clock.
Fixes: 4f86e81748 ("drm/sun4i: Add support for H3 HDMI PHY variant")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-17-jernej.skrabec@siol.net
Both mixers have similar capabilities as others SoCs with DE2.
First mixer has 1 VI and 3 UI planes and supports HW scaling on all
planes.
Second mixer has 1 VI and 1 UI planes and also supports HW scaling on
all planes.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-15-jernej.skrabec@siol.net
TV TCONs are always connected to TV or HDMI encoder, so it doesn't make
sense to check if panel or bridge is connected to them.
Check if TCON has channel 0 and only then check for connected panel or
bridges.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-13-jernej.skrabec@siol.net
LVDS and RGB interfaces are always connected to TCONs which have channel
0. It doesn't make sense to try to init them on TV TCONs.
Add a check if TCON has channel 0 before trying to init LVDS or RGB
interface.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-12-jernej.skrabec@siol.net
Current "old" method to find engine worked pretty well for DE2. However,
it doesn't work when TCON TOP is between mixer (engine) and TCON. TCON
TOP has multiple input ports, but current engine search algorithm
expects only one.
This can be fixed by first looking for output port id and selecting
matching input by subtracting 1 for the next round. This work even if
there is only one input and output.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-11-jernej.skrabec@siol.net
TV TCONs (channel 1 only) are always connected to TV or HDMI encoder.
Because of that, all output endpoints on such TCON node will point to a
encoder which is part of component framework.
Correct current graph traversing algorithm in such way that it doesn't
skip output enpoints with id 0 on TV TCONs.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-10-jernej.skrabec@siol.net
TCON TOP is different from other nodes in graph by having 3 input and 3
output ports. Additionally, connection to TV TCON might lead back to
HDMI mux input port, creating loops.
Add support for traversing such graph.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-9-jernej.skrabec@siol.net
Until now, each node has one input port and one output port. However,
with TCON TOP this is no longer true. It has 3 input and 3 output ports.
In order to prepare to this situation, split out the code which checks
all endpoints in input port and adds available components to fifo.
This patch doesn't do any functional change.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-8-jernej.skrabec@siol.net
sun4i_drv_add_endpoints() has a memory leak since it uses of_node_put()
when remote is equal to NULL and does nothing when remote has a valid
pointer.
Invert the logic to fix memory leak.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-7-jernej.skrabec@siol.net
As already described in DT binding, TCON TOP is responsible for
configuring display pipeline. In this initial driver focus is on HDMI
pipeline, so TVE and LCD configuration is not implemented.
Implemented features:
- HDMI source selection
- clock driver (TCON and DSI gating)
- connecting mixers and TCONS
Something similar also existed in previous SoCs, except that it was part
of first TCON.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-6-jernej.skrabec@siol.net
- A reversion of a commit in drm/sun4i to fix a run-time fault.
- Various fixes to the sii8620 bridge.
- Small bugfix to correctly check stride in atmel-hlcdc.
-----BEGIN PGP SIGNATURE-----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=ngPr
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2018-06-21' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Fixes for v4.18-rc2:
- A reversion of a commit in drm/sun4i to fix a run-time fault.
- Various fixes to the sii8620 bridge.
- Small bugfix to correctly check stride in atmel-hlcdc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/787d4bef-a579-4046-d0fc-f8c2c5b80c25@linux.intel.com
This reverts commit 2c17a4368a.
The offending commit triggers a run-time fault when accessing the panel
element of the sun4i_tcon structure when no such panel is attached.
It was apparently assumed in said commit that a panel is always used with
the TCON. Although it is often the case, this is not always true.
For instance a bridge might be used instead of a panel.
This issue was discovered using an A13-OLinuXino, that uses the TCON
in RGB mode for a simple DAC-based VGA bridge.
Cc: stable@vger.kernel.org
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613081647.31183-1-paul.kocialkowski@bootlin.com
Disabling CONFIG_PM produces a compile time warning when these
functions are not referenced:
drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c:1072:12: error: 'sun6i_dsi_runtime_suspend' defined but not used [-Werror=unused-function]
static int sun6i_dsi_runtime_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c:1043:12: error: 'sun6i_dsi_runtime_resume' defined but not used [-Werror=unused-function]
static int sun6i_dsi_runtime_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 133add5b5a ("drm/sun4i: Add Allwinner A31 MIPI-DSI controller support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180525155030.3667352-1-arnd@arndb.de
UAPI Changes:
- Add support for a generic plane alpha property to sun4i, rcar-du and atmel-hclcdc. (Maxime)
Core Changes:
- Stop looking at legacy plane->fb and crtc members in atomic drivers. (Ville)
- mode_valid return type fixes. (Luc)
- Handle zpos normalization in the core. (Peter)
Driver Changes:
- Implement CTM, plane alpha and generic async cursor support in vc4. (Stefan)
- Various fixes for HPD and aux chan in drm_bridge/analogix_dp. (Lin, Zain, Douglas)
- Add support for MIPI DSI to sun4i. (Maxime)
-----BEGIN PGP SIGNATURE-----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=9LYY
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-04-26' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v4.18:
UAPI Changes:
- Add support for a generic plane alpha property to sun4i, rcar-du and atmel-hclcdc. (Maxime)
Core Changes:
- Stop looking at legacy plane->fb and crtc members in atomic drivers. (Ville)
- mode_valid return type fixes. (Luc)
- Handle zpos normalization in the core. (Peter)
Driver Changes:
- Implement CTM, plane alpha and generic async cursor support in vc4. (Stefan)
- Various fixes for HPD and aux chan in drm_bridge/analogix_dp. (Lin, Zain, Douglas)
- Add support for MIPI DSI to sun4i. (Maxime)
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Thu 26 Apr 2018 08:21:01 PM AEST
# gpg: using RSA key FE558C72A67013C3
# gpg: Can't check signature: public key not found
Link: https://patchwork.freedesktop.org/patch/msgid/b33da7eb-efc9-ae6f-6f69-b7acd6df6797@mblankhorst.nl
The reverted commit broke LVDS output on TBS A711 Tablet. That tablet
has simple-panel node that has fixed pixel clock-frequency that A83T
SoC used in the tablet can't generate exactly.
Requested rate is 52000000 and rounded_rate is calculated as 51857142.
It's close enough for it to work in practice, but with strict check
in the reverted commit, the mode is rejected needlessly in this case.
DT allows to specify a range of values for simple-panel/clock-frequency,
but driver doesn't respect that ATM. Given that TBS A711 is the single
user of sun4i-lvds driver, let's revert that commit for now, until
a better solution for the problem is found.
Also see: https://patchwork.kernel.org/patch/9446385/ for relevant
discussion (or search for "[RFC] drm/sun4i: rgb: Add 5% tolerance
to dot clock frequency check").
Fixes: e4e4b7ad50 ("drm/sun4i: add lvds mode_valid function")
Reported-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180421045155.15332-1-megous@megous.com
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Most of the Allwinner SoCs since the A31 share the same MIPI-DSI
controller.
While that controller is mostly undocumented, the code is out there and has
been cleaned up in order to be integrated into DRM. However, there's still
some dark areas that are a bit unclear about how the block exactly
operates.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ad9e6224fced87c0889ddd2765d1942610061f72.1522835818.git-series.maxime.ripard@bootlin.com
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJauCZfAAoJEHm+PkMAQRiGWGUH/2rhdQDkoJpYWnjaQkolECG8
MxpGE7nmIIHxQcbSDdHTGJ8IhVm6Z5wZ7ym/PwCDTT043Y1y341sJrIwL2/nTG6d
HVidk8hFvgN6QzlzVAHT3ZZMII/V9Zt+VV5SUYLGnPAVuJNHo/6uzWlTU5g+NTFo
IquFDdQUaGBlkKqby+NoAFnkV1UAIkW0g22cfvPnlO5GMer0gusGyVNvVp7TNj3C
sqj4Hvt3RMDLMNe9RZ2pFTiOD096n8FWpYftZneUTxFImhRV3Jg5MaaYZm9SI3HW
tXrv/LChT/F1mi5Pkx6tkT5Hr8WvcrwDMJ4It1kom10RqWAgjxIR3CMm448ileY=
=YKUG
-----END PGP SIGNATURE-----
Backmerge tag 'v4.16-rc7' into drm-next
Linux 4.16-rc7
This was requested by Daniel, and things were getting
a bit hard to reconcile, most of the conflicts were
trivial though.
Now that we have the guarantee that we will have only a single YUV plane,
actually support them. The way it works is not really straightforward,
since we first need to enable the YUV mode in the plane that we want to
setup, and then we have a few registers to setup the YUV buffer and
parameters.
We also need to setup the color correction to actually have something
displayed.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/66088c1398bd3189123f28a89a7ccc669fe9f296.1519931807.git-series.maxime.ripard@bootlin.com
Paul Kocialkowski