...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without pm_runtime_{get,put}_sync calls in place, reading
vbus status via /sys causes the following error:
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0ab060
pgd = b333e822
[fa0ab060] *pgd=48011452(bad)
[<c05261b0>] (musb_default_readb) from [<c0525bd0>] (musb_vbus_show+0x58/0xe4)
[<c0525bd0>] (musb_vbus_show) from [<c04c0148>] (dev_attr_show+0x20/0x44)
[<c04c0148>] (dev_attr_show) from [<c0259f74>] (sysfs_kf_seq_show+0x80/0xdc)
[<c0259f74>] (sysfs_kf_seq_show) from [<c0210bac>] (seq_read+0x250/0x448)
[<c0210bac>] (seq_read) from [<c01edb40>] (__vfs_read+0x1c/0x118)
[<c01edb40>] (__vfs_read) from [<c01edccc>] (vfs_read+0x90/0x144)
[<c01edccc>] (vfs_read) from [<c01ee1d0>] (SyS_read+0x3c/0x74)
[<c01ee1d0>] (SyS_read) from [<c0106fe0>] (ret_fast_syscall+0x0/0x54)
Solution was suggested by Tony Lindgren <tony@atomide.com>.
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On dm3730 there are enumeration problems after resume.
Investigation led to the cause that the MUSB_POWER_SOFTCONN
bit is not set. If it was set before suspend (because it
was enabled via musb_pullup()), it is set in
musb_restore_context() so the pullup is enabled. But then
musb_start() is called which overwrites MUSB_POWER and
therefore disables MUSB_POWER_SOFTCONN, so no pullup is
enabled and the device is not enumerated.
So let's do a subset of what musb_start() does
in the same way as musb_suspend() does it. Platform-specific
stuff it still called as there might be some phy-related stuff
which needs to be enabled.
Also interrupts are enabled, as it was the original idea
of calling musb_start() in musb_resume() according to
Commit 6fc6f4b87c ("usb: musb: Disable interrupts on suspend,
enable them on resume")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It really should be DEVICE_ATTR_WO(), no need to "open code" it.
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of "open coding" a DEVICE_ATTR() define, use the
DEVICE_ATTR_RW() macro instead, which does everything properly instead.
This does require a few static functions to be renamed to work properly,
but thanks to a script from Joe Perches, this was easily done.
Reported-by: Joe Perches <joe@perches.com>
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is only one clock for the DA8xx MUSB device, so we don't need the
con_id, so remove it. This way we don't have to add an unnecessary
property to the device tree bindings for the clock.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix the following build warning:
drivers/usb/musb/musb_host.c:1809:8: warning: variable 'pipe' set but not used [-Wunused-but-set-variable]
by removing the pipe variable in musb_host_rx()
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix the following warning
drivers/usb/musb/musb_host.c:223:8: warning: variable 'frame' set but not used [-Wunused-but-set-variable]
by remove the frame variable in musb_start_urb().
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When babble condition happens, the musb controller might automatically
turns off VBUS. On DA8xx platform, the controller generates drvvbus
interrupt for turning off VBUS along with the babble interrupt.
In this case, we should handle the babble interrupt first and recover
from the babble condition.
This change ignores the drvvbus interrupt if babble interrupt is also
generated at the same time, so the babble recovery routine works
properly.
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along with
phy and chipidea enhancements. There's also a lot of SPDX tags and
license boilerplate cleanups as well, which provide some churn in the
diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see happen.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgm/Vw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yktXwCdGgpInfOEvOGFd83EPDL7a1ncyc4AoM5wI8yl
1CeLipqVIN3IsMMJptvb
=zvDI
-----END PGP SIGNATURE-----
Merge tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along
with phy and chipidea enhancements. There's also a lot of SPDX tags
and license boilerplate cleanups as well, which provide some churn in
the diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see
happen.
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
USB: usbfs: compute urb->actual_length for isochronous
usb: core: message: remember to reset 'ret' to 0 when necessary
USB: typec: Remove remaining redundant license text
USB: typec: add SPDX identifiers to some files
USB: renesas_usbhs: rcar?.h: add SPDX tags
USB: chipidea: ci_hdrc_tegra.c: add SPDX line
USB: host: xhci-debugfs: add SPDX lines
USB: add SPDX identifiers to all remaining Makefiles
usb: host: isp1362-hcd: remove a couple of redundant assignments
USB: adutux: remove redundant variable minor
usb: core: add a new usb_get_ptm_status() helper
usb: core: add a 'type' parameter to usb_get_status()
usb: core: introduce a new usb_get_std_status() helper
usb: core: rename usb_get_status() 'type' argument to 'recip'
usb: core: add Status Type definitions
USB: gadget: Remove redundant license text
USB: gadget: function: Remove redundant license text
USB: gadget: udc: Remove redundant license text
USB: gadget: legacy: Remove redundant license text
...
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now struct musb has the timer (dev_timer) for glue drivers, so let's
remove the duplicated timer defined in dsps glue driver, and use
dev_timer defined in struct musb.
Signed-off-by: Bin Liu <b-liu@ti.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Instead of a per-device static timer variable, a spare timer "dev_timer"
is added to the musb structure for devices to use for their per-device
timer.
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1397608
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is some registers defined in da8xx.c though they are not used.
These registers are also defined and used in musb_cppi41.c
Remove these defines from da8xx.c.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a kernel oops when unloading the driver due to usb_put_phy
being called after usb_phy_generic_unregister when the device is
detached. Calling usb_phy_generic_unregister causes x->dev->driver to
be NULL in usb_put_phy and results in a NULL pointer dereference.
Cc: stable@vger.kernel.org # v4.3+
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sunxi musb has a bug where sometimes it will generate a babble
error on device disconnect instead of a disconnect IRQ. When this
happens the musb controller switches from host mode to device mode
(it clears MUSB_DEVCTL_HM/MUSB_DEVCTL_SESSION and sets
MUSB_DEVCTL_BDEVICE) and gets stuck in this state.
The babble error is misdetected as a bus reset because MUSB_DEVCTL_HM
was cleared.
To fix this, use is_host_active() rather than (devctl & MUSB_DEVCTL_HM)
to detect babble error so that sunxi musb babble recovery can handle it
by restoring the mode. This information is provided by the driver logic
and does not rely on register contents.
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the number of channels is set to 15 but in the case of DA8xx,
the number of channels is 4.
Update the driver to configure the number of channels at runtime.
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The way to configure the DMA mode on DA8xx is different from DSPS.
Add a new function to configure DMA mode on DA8xx and use a callback
to call the right function based on the platform.
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DA8xx and DSPS platforms don't use the same address for few registers.
On Da8xx, this is causing some issues (e.g. teardown that doesn't work).
Configure the address of the register during the init and use them instead
of constants.
Cc: stable@vger.kernel.org # v4.12+
Reported-by: nsekhar@ti.com
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The musb delayed irq work was never flushed on suspend, something which
since 4.9 can lead to an external abort if the work is scheduled after
the grandparent's clock has been disabled:
PM: Suspending system (mem)
PM: suspend of devices complete after 125.224 msecs
PM: suspend devices took 0.132 seconds
PM: late suspend of devices complete after 7.423 msecs
PM: noirq suspend of devices complete after 7.083 msecs
suspend debug: Waiting for 5 second(s).
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd0262c60
...
[<c054880c>] (musb_default_readb) from [<c0547b5c>] (musb_irq_work+0x48/0x220)
[<c0547b5c>] (musb_irq_work) from [<c014f8a4>] (process_one_work+0x1f4/0x758)
[<c014f8a4>] (process_one_work) from [<c014fe5c>] (worker_thread+0x54/0x514)
[<c014fe5c>] (worker_thread) from [<c015704c>] (kthread+0x128/0x158)
[<c015704c>] (kthread) from [<c0109330>] (ret_from_fork+0x14/0x24)
Commit 2bff3916fd ("usb: musb: Fix PM for hub disconnect") started
scheduling musb_irq_work with a delay of up to a second and with
retries thereby making this easy to trigger, for example, by suspending
shortly after a disconnect.
Note that we set a flag to prevent the irq work from rescheduling itself
during suspend and instead process a disconnect immediately. This takes
care of the case where we are disconnected shortly before suspending.
However, when in host mode, a disconnect while suspended will still
go unnoticed and thus prevent the controller from runtime suspending
upon resume as the session bit is always set. This will need to be
addressed separately.
Fixes: 550a7375fe ("USB: Add MUSB and TUSB support")
Fixes: 467d5c9807 ("usb: musb: Implement session bit based runtime PM for musb-core")
Fixes: 2bff3916fd ("usb: musb: Fix PM for hub disconnect")
Cc: stable <stable@vger.kernel.org> # 4.9
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current session-bit quirk implementation does not prevent the retry
counter from underflowing, something which could break runtime PM and
keep the device active for a very long time (about 2^32 seconds) after a
disconnect.
This notably breaks the B-device timeout case, but could potentially
cause problems also when the controller is operating as an A-device.
Fixes: 2bff3916fd ("usb: musb: Fix PM for hub disconnect")
Cc: stable <stable@vger.kernel.org> # 4.9
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The musb_dsps driver is special in that the parent (glue) device's
driver is accessing registers mapped by the child. The clock is however
shared and is managed by the grandparent device.
Since commit 869c597829 ("usb: musb: dsps: add support for suspend and
resume") the dsps driver has been accessing these registers as part of
suspend and resume.
The parent driver obviously cannot runtime resume the child during
system suspend and is currently relying on the fact that the child will
be RPM_ACTIVE throughout suspend. The suspend implementation also makes
sure to check that the child is indeed present (and hence the clock
enabled) before accessing the registers.
Let's add an explicit runtime resume of the glue device itself to enable
the clock before doing the register accesses in case these assumptions ever
change (i.e. if the child is left runtime suspended).
Note that the glue-timer cancellation is moved after the child-presence
check to keep error handling simple. This should be fine as the timer is
not setup until the controller is being registered and at that time
glue->musb and its driver data have already been initialised.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that the controller is runtime resumed when system suspending
to avoid an external abort when accessing the interrupt registers:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd025840a
...
[<c05481a4>] (musb_default_readb) from [<c0545abc>] (musb_disable_interrupts+0x84/0xa8)
[<c0545abc>] (musb_disable_interrupts) from [<c0546b08>] (musb_suspend+0x38/0xb8)
[<c0546b08>] (musb_suspend) from [<c04a57f8>] (platform_pm_suspend+0x3c/0x64)
This is easily reproduced on a BBB by enabling the peripheral port only
(as the host port may enable the shared clock) and keeping it
disconnected so that the controller is runtime suspended. (Well, you
would also need to the not-yet-merged am33xx-suspend patches by Dave
Gerlach to be able to suspend the BBB.)
This is a regression that was introduced by commit 1c4d0b4e18 ("usb:
musb: Remove pm_runtime_set_irq_safe") which allowed the parent glue
device to runtime suspend and thereby exposed a couple of older issues:
Register accesses without explicitly making sure the controller is
runtime resumed during suspend was first introduced by commit c338412b5d
("usb: musb: unconditionally save and restore the context on suspend")
in 3.14.
Commit a1fc1920aa ("usb: musb: core: make sure musb is in RPM_ACTIVE on
resume") later started setting the RPM status to active during resume,
and this was also implicitly relying on the parent always being active.
Since commit 71723f9546 ("PM / runtime: print error when activating a
child to unactive parent") this now also results in the following
warning:
musb-hdrc musb-hdrc.0: runtime PM trying to activate child device
musb-hdrc.0 but parent (47401400.usb) is not active
This patch has been verified on 4.13-rc2, 4.12 and 4.9 using a BBB
(the dsps glue would always be active also in 4.8).
Fixes: c338412b5d ("usb: musb: unconditionally save and restore the context on suspend")
Fixes: a1fc1920aa ("usb: musb: core: make sure musb is in RPM_ACTIVE on resume")
Fixes: 1c4d0b4e18 ("usb: musb: Remove pm_runtime_set_irq_safe")
Cc: stable <stable@vger.kernel.org> # 4.8+
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fifo memory allocation in mode_2_cfg[] doesn't utilize all the 4KB
memory.
Increse some endpoint fifo buffers to fully use all the 4KB memory. Now
we can support more webcam usecases on DA8xx.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are multiple places in usb core or controller driver which returns
-EMSGSIZE when a class driver queueing urb failed, so the "Message too
long" log doesn't help much for understanding the error.
Let the musb driver to specifically print a error message when
musb_urb_enqueue() returns -EMSGSIZE.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Print an error message with qh maxpacket size and hb_mult when hwep
allocation failed, so we have a better idea why it is failed.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add helper function musb_ep_xfertype_string() to return the ep transfer
type string.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68fe05e2a4 ("usb: musb: fix tx fifo flush handling") drops the
1ms delay trying to solve the long disconnect time issue when
application queued many tx urbs. However, the 1ms delay is needed for
some use cases, for example, without the delay, reconnecting AR9271 WIFI
dongle no longer works if the connection is dropped from the AP.
So let's add back the 1ms delay in musb_h_tx_flush_fifo(), and solve the
long disconnect time problem with a separate patch for
usb_hcd_flush_endpoint().
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify return logic to avoid unnecessary variable assignment.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the port_window support in DMAengine and the sDMA driver we can
convert the driver to DMAengine.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle the DMA TX in a similar way as we do for the RX: in the DMA
completion callback.
Since we are no longer using DMA completion interrupt for the TX we can as
wall keep these interrupts disabled, but keep the handler for debug
purposes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of requesting the DMA channel in tusb_omap_dma_allocate() do it
when the controller is created and in runtime work from the DMA channel
pool.
This change is needed for the DMAengine conversion of the driver since the
tusb_omap_dma_allocate() is called in interrupt context which might lead
to lock within the DMAengine API when requesting channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the DMA we have ch (channel), dmareq and sync_dev parameters both
within the tusb_omap_dma_ch and tusb_omap_dma struct.
By creating a common struct the code can be simplified when selecting
between the shared or multichannel DMA parameters.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having one musb_ep_select() instead the two calls in if/else is the same
thing, but makes the code a bit simpler to follow.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using the g_ncm for networking this flag will make sure that the
buffer is aligned to 32bit so the DMA can be used to offload the data
movement.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For tusb6010 the DMA functionality only possible if the buffer is 32bit
aligned (SYNC access to FIFO) since with ASYNC access the TX/RX offset
registers will corrupt eventually.
The MUSB_G_NO_SKB_RESERVE will set the quirk_avoids_skb_reserve flag in
usb_gadget struct to provide correctly aligned buffer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dma_request_slave_channel() failed to return a channel,
then the driver will print an error and request to defer probe,
regardless of the cause of the failure.
Defer if the DMA is not ready yet otherwise print an error.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently VBUS is turned off while a usb device is detached, and turned
on again by the polling routine. This short period VBUS loss prevents
usb modem to switch mode.
VBUS should be constantly on for host-only mode, so this changes the
driver to not turn off VBUS for host-only mode.
Fixes: 2f3fd2c5bd ("usb: musb: Prepare dsps glue layer for PM runtime support")
Cc: stable@vger.kernel.org #v4.11
Reported-by: Moreno Bartalucci <moreno.bartalucci@tecnorama.it>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have one register for each EP to set the maximum packet size for both
TX and RX.
If for example an RX programming would happen before the previous TX
transfer finishes we would reset the TX packet side.
To fix this issue, only modify the TX or RX part of the register.
Fixes: 550a7375fe ("USB: Add MUSB and TUSB support")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d8e5f0eca1 ("usb: musb: Fix hardirq-safe hardirq-unsafe
lock order error") caused a regression where musb keeps trying to
enable host mode with no cable connected. This seems to be caused
by the fact that now phy is enabled earlier, and we are wrongly
trying to force USB host mode on an OTG port. The errors we are
getting are "trying to suspend as a_idle while active".
For ports configured as OTG, we should not need to do anything
to try to force USB host mode on it's OTG port. Trying to force host
mode in this case just seems to completely confuse the musb state
machine.
Let's fix the issue by making musb_host_setup() attempt to force the
mode only if port_mode is configured for host mode.
Fixes: d8e5f0eca1 ("usb: musb: Fix hardirq-safe hardirq-unsafe lock order error")
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe function is not __init since it can be called for deferred
probing or when unbinding/rebinding the device, and therefore it must
not reference objects in __initdata, as pointed out by this link
time warning:
WARNING: drivers/usb/musb/da8xx.o(.text+0x9d4): Section mismatch in reference from the function da8xx_probe() to the (unknown reference) .init.data:(unknown)
This removes the annotation.
Reported-by: Olof's autobuilder <olof@lixom.net>
Fixes: d6299b6efb ("usb: musb: Add support of CPPI 4.1 DMA controller to DA8xx")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA may hang up if a teardown is initiated while an endpoint is still
active (Advisory 2.3.27 of DA8xx errata).
To workaround this issue, add a delay before to initiate the teardown.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, only the PIO mode is supported.
This add support of CPPI 4.1 to DA8xx.
As in DA8xx the CPPI 4.1 DMA is a part of the USBSS, create the CPPI 4.1
device as a child of USB.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
[b-liu@ti.com: minor tweak in the commit log]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the DA8xx, USB and CPPI 4.1 are sharing the same interrupt line.
Update the driver to request a shared irq.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DIV_ROUND_UP is bit useful than series of "/" and "%" operations.
Replace "/%" sequence with DIV_ROUND_UP macro.
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cleanly iounmap the pointer in error and exit paths.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CPPI 4.1 driver polls register to workaround the premature TX
interrupt issue, but it causes audio playback underrun when triggered in
Isoch transfers.
Isoch doesn't do back-to-back transfers, the TX should be done by the
time the next transfer is scheduled. So skip this polling workaround for
Isoch transfer.
Fixes: a655f481d8 ("usb: musb: musb_cppi41: handle pre-mature TX complete interrupt")
Cc: <stable@vger.kernel.org> #4.1+
Reported-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add code comment to make it clear that the fall-through is intentional.
Read the link for more details: https://lkml.org/lkml/2017/2/9/292
Addresses-Coverity-ID: 1397608
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Despite the CPPI 4.1 is a generic DMA, it is tied to USB.
On the DSPS, CPPI 4.1 interrupt's registers are in USBSS (the MUSB glue).
Currently, to enable / disable and clear interrupts, the CPPI 4.1 driver
maps and accesses to USBSS's register, which making CPPI 4.1 driver not
really generic.
Move the interrupt management to DSPS driver.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A pointer to musb is now present in the dma_controller structure.
Remove the one present in tusb_omap_dma structure.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A pointer to musb is now present in the dma_controller structure.
Remove the one present in cppi41_dma_controller structure.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A pointer to musb is now present in the dma_controller structure.
Remove the one present in cppi structure.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update cppi41_dma_callback() to detect an aborted transfer.
This was not required before because cppi41_dma_callback() was only
invoked on transfer completion.
In order to make CPPI 4.1 driver more generic, cppi41_dma_callback()
will be invoked after a transfer abort in order to let the MUSB driver
perform some action such as acknowledge the interrupt that may be fired
during a teardown.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the CPPI 4.1 driver is not completely generic and
only works on DSPS. This is because of IRQ management.
Add a callback to dma_controller that could be invoked on DMA completion
to acknowledge the IRQ.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following sparse warning:
drivers/usb/musb/musb_dsps.c:270:6: warning:
symbol 'dsps_musb_clear_ep_rxintr' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allwinner H3/V3s features a variant of MUSB controller, which lacks one
endpoint.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[b-liu@ti.com: added usb: to commit subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Declare dev_pm_ops structures as const as they are only stored in the pm
field of a device_driver structure. This field is of type const, so
dev_pm_ops structures having similar properties can be declared const
too.
Size details after cross compiling the .o file for arm
architecture.
File size before: drivers/usb/musb/omap2430.o
text data bss dec hex filename
4141 400 8 4549 11c5 usb/musb/omap2430.o
File size after: drivers/usb/musb/omap2430.o
text data bss dec hex filename
4333 200 8 4541 11bd usb/musb/omap2430.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
[b-liu@ti.com: added omap2430 in commit subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can now configure the PMIC interrupt to provide us VBUS
events. In that case we don't need to constantly poll the
status and can make it optional. This is only wired up
for the mini-B interface on beaglebone.
Note that eventually we should get also the connect status
for the host interface when the am335x internal PM coprocessor
provides us with an IRQ chip. For now, we still need to poll
for the host mode status.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_PM_SLEEP is disabled, SIMPLE_DEV_PM_OPS does not use
bfin_resume and bfin_suspend even if CONFIG_PM is enabled:
drivers/usb/musb/blackfin.c:602:12: warning: ‘bfin_resume’ defined but
not used [-Wunused-function]
static int bfin_resume(struct device *dev)
^~~~~~~~~~~
drivers/usb/musb/blackfin.c:585:12: warning: ‘bfin_suspend’ defined but
not used [-Wunused-function]
static int bfin_suspend(struct device *dev)
^~~~~~~~~~~~
The preprocessor condition should be on CONFIG_PM_SLEEP, not on CONFIG_PM.
However it is better to mark these functions as __maybe_unused.
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dsps glue uses PLATFORM_DEVID_AUTO when creating the musb-hdrc
platform devices, this causes that the id will change in each system
depending on the order of driver probe, the order of the usb instances
defined in device-tree, or the list of enabled devices which use also
PLATFORM_DEVID_AUTO in kernel config. This id inconsistency causes
trouble in shell scripting or user guide documentation.
So switch it to static id, starting from 0 to the musb instance with
lower MMR offset. This scheme is also aligned to the naming in the SoC.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the musb ug, force_host bit is allowed to be set along with
force_hs or force_fs bit.
It could help to implement forced host mode via testmode on Nokia N900.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch just uses the resource-managed extcon API when registering
the extcon notifier.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On da8xx, VBUS is not maintained during suspend when musb is in host mode.
On resume, all the connected devices will be disconnected and then will
be enumerated again.
This happens because MUSB_DEVCTL is cleared during suspend.
Use the quirk MUSB_PRESERVE_SESSION to preseve MUSB_DEVCTL during suspend.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On da8xx, VBUS is not maintained during suspend when musb is in host mode.
On resume, all the connected devices will be disconnected and then will
be enumerated again.
This happens because MUSB_DEVCTL is cleared during suspend.
Add a quirk to not clear MUSB_DEVCTL and then preserve the session during
a suspend.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement PM methods specifics for da8xx glue.
The only thing to do is to power off the phy.
As the registers are in retention during suspend,
there is no need to save them.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The session is cleared in the core whenever musb_platform_disable() is
called, so clearing it in the glue driver *_musb_disable() is redundant.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb_generic_disable() only has two lines of code. So remove it and let
the callers directly call those two lines.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DA8xx driver is registering and using the CPPI 3.0 DMA controller but
actually, the DA8xx has a CPPI 4.1 DMA controller.
Remove the CPPI 3.0 quirk and methods.
Fixes: f8e9f34f80 ("usb: musb: Fix up DMA related macros")
Fixes: 7f6283ed6f ("usb: musb: Set up function pointers for DMA")
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While testing musb host mode cable plugging on a BeagleBone, I came across this
error:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd1dcfc60
...
[<bf668390>] (musb_default_readb [musb_hdrc]) from [<bf668578>] (musb_irq_work+0x1c/0x180 [musb_hdrc])
[<bf668578>] (musb_irq_work [musb_hdrc]) from [<c0156554>] (process_one_work+0x2b4/0x808)
[<c0156554>] (process_one_work) from [<c015767c>] (worker_thread+0x3c/0x550)
[<c015767c>] (worker_thread) from [<c015d568>] (kthread+0x104/0x148)
[<c015d568>] (kthread) from [<c01078d0>] (ret_from_fork+0x14/0x24)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 467d5c9807 ("usb: musb: Implement session bit based runtime PM for
musb-core") started implementing musb generic runtime PM support by
introducing devctl register session bit based state control.
This caused a regression where if a USB mass storage device is connected
to a USB hub, we can get:
usb 1-1: reset high-speed USB device number 2 using musb-hdrc
usb 1-1: device descriptor read/64, error -71
usb 1-1.1: new high-speed USB device number 4 using musb-hdrc
This is because before the USB storage device is connected, musb is
in OTG_STATE_A_SUSPEND. And we currently only set need_finish_resume
in musb_stage0_irq() and the related code calling finish_resume_work
in musb_resume() and musb_runtime_resume() never gets called.
To fix the issue, we can call schedule_delayed_work() directly in
musb_stage0_irq() to have finish_resume_work run.
And we should no longer never get interrupts when when suspended.
We have changed musb to no longer need pm_runtime_irqsafe().
The need_finish_resume flag was added in commit 9298b4aad3 ("usb:
musb: fix device hotplug behind hub") and no longer applies as far
as I can tell. So let's just remove the earlier code that no longer
is needed.
Fixes: 467d5c9807 ("usb: musb: Implement session bit based runtime PM for musb-core")
Reported-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Declare musb_hdrc_config structures as const as they are only stored in
the config field of a musb_hdrc_platform_data structure. This field is of
type const, so musb_hdrc_config structures having this property can be
made const too.
Done using Coccinelle:
@r disable optional_qualifier@
identifier x;
position p;
@@
static struct musb_hdrc_config x@p={...};
@ok@
struct musb_hdrc_platform_data pdata;
identifier r.x;
position p;
@@
pdata.config=&x@p;
@bad@
position p != {r.p,ok.p};
identifier r.x;
@@
x@p
@depends on !bad disable optional_qualifier@
identifier r.x;
@@
+const
struct musb_hdrc_config x;
File size before:
text data bss dec hex filename
1212 338 0 1550 60e drivers/usb/musb/jz4740.o
File size after:
text data bss dec hex filename
1268 290 0 1558 616 drivers/usb/musb/jz4740.o
File size before:
text data bss dec hex filename
6151 333 16 6500 1964 drivers/usb/musb/sunxi.o
File size after:
text data bss dec hex filename
6215 269 16 6500 1964 drivers/usb/musb/sunxi.o
File size before:
text data bss dec hex filename
3668 864 0 4532 11b4 drivers/usb/musb/ux500.o
File size after:
text data bss dec hex filename
3724 808 0 4532 11b4 drivers/usb/musb/ux500.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MUSB driver now has runtime PM support, but the debugfs driver misses
the PM _get/_put() calls, which could cause MUSB register access
failure.
Cc: stable@vger.kernel.org # 4.9+
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function bfin_fifo_offset is defined but not used:
drivers/usb/musb/blackfin.c:36:12: warning: ‘bfin_fifo_offset’ defined
but not used [-Wunused-function]
static u32 bfin_fifo_offset(u8 epnum)
^~~~~~~~~~~~~~~~
Adding bfin_fifo_offset to bfin_ops fixes this warning and allows musb
core to call this function instead of default_fifo_offset.
Fixes: cc92f6818f ("usb: musb: Populate new IO functions for blackfin")
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function musb_run_resume_work is called only when CONFIG_PM is
enabled. So this function should not be defined when CONFIG_PM is
disabled. Otherwise the compiler issues a warning:
drivers/usb/musb/musb_core.c:2057:12: error: ‘musb_run_resume_work’ defined but
not used [-Werror=unused-function]
static int musb_run_resume_work(struct musb *musb)
^~~~~~~~~~~~~~~~~~~~
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When unloading omap2430, we can get the following splat:
WARNING: CPU: 1 PID: 295 at kernel/irq/manage.c:1478 __free_irq+0xa8/0x2c8
Trying to free already-free IRQ 4
...
[<c01a8b78>] (free_irq) from [<bf0aea84>]
(musbhs_dma_controller_destroy+0x28/0xb0 [musb_hdrc])
[<bf0aea84>] (musbhs_dma_controller_destroy [musb_hdrc]) from
[<bf09f88c>] (musb_remove+0xf0/0x12c [musb_hdrc])
[<bf09f88c>] (musb_remove [musb_hdrc]) from [<c056a384>]
(platform_drv_remove+0x24/0x3c)
...
This is because the irq number in use is 260 nowadays, and the dma
controller is using u8 instead of int.
Fixes: 6995eb68aa ("USB: musb: enable low level DMA operation for Blackfin")
Signed-off-by: Tony Lindgren <tony@atomide.com>
[b-liu@ti.com: added Fixes tag]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During dma teardown for dequque urb, if musb load is high, musb might
generate bogus rx ep interrupt even when the rx fifo is flushed. In such
case any of the follow log messages could happen.
musb_host_rx 1853: BOGUS RX2 ready, csr 0000, count 0
musb_host_rx 1936: RX3 dma busy, csr 2020
As mentioned in the current inline comment, clearing ep interrupt in the
teardown path avoids the bogus interrupt, so implement clear_ep_rxintr()
callback.
This bug seems to be existing since the initial driver for musb support,
but I only validated the fix back to v4.1, so only cc stable for v4.1+.
cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During dma teardown for dequque urb, if musb load is high, musb might
generate bogus rx ep interrupt even when the rx fifo is flushed. In such
case any of the follow log messages could happen.
musb_host_rx 1853: BOGUS RX2 ready, csr 0000, count 0
musb_host_rx 1936: RX3 dma busy, csr 2020
As mentioned in the current inline comment, clearing ep interrupt in the
teardown path avoids the bogus interrupt.
Clearing ep interrupt is platform dependent, so this patch adds a
platform callback to allow glue driver to clear the ep interrupt.
This bug seems to be existing since the initial driver for musb support,
but I only validated the fix back to v4.1, so only cc stable for v4.1+.
cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The DA8xx OTG PHY has some issues when it is forced in host or
peripheral mode. Actually, most of the time, OTG is the best mode
because host or peripheral mode are only required for hardware that
miss some circuitry.
Init the PHY mode OTG mode by default.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first attempt to read a register may fail because the clock may not
be enabled, and then the probe of musb driver will fail.
Call clk_prepare_enable() before the first register read.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds DT support for TI DA8xx/OMAP-L1x/AM17xx/AM18xx MUSB driver
Signed-off-by: Petr Kulhavy <petr@barix.com>
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the function musb_get_mode() to get the DT property "dr_mode"
Signed-off-by: Petr Kulhavy <petr@barix.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: David Lechner <david@lechnology.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point having this complaint to be dev_err as it is just adding
noise to bootlog.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace pr_err with dev_err to print also device name.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't complain on -EPROBE_DEFER when initializing controller,
the driver probe will be retried later.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sunxi musb has a bug where sometimes it will generate a babble
error on device disconnect instead of a disconnect irq. When this
happens the musb-controller switches from host mode to device mode
(it clears MUSB_DEVCTL_SESSION and sets MUSB_DEVCTL_BDEVICE) and
gets stuck in this state.
Clearing this requires reporting Vbus low for 200 or more ms, but
on some devices Vbus is simply always high (host-only mode, no Vbus
control).
This commit adds a sunxi_musb_recover() callback which makes
sunxi_musb_work call phy_set_mode with the current mode, which
will force end the current session.
This fixes the musb controller getting stuck in this state on systems
without Vbus control; and also fixes the need to unplug the usb-b ->
usb-a cable to get out of this state on systems with Vbus control.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The musb core already handles babble interrupts, so the sunxi glue
having its own custom handling is redundant.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove comments about resume signalling being stopped from
GetPortStatus, something which is no longer the case.
Fixes: 8ed1fb790e ("usb: musb: finish suspend/reset work...")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
-----BEGIN PGP SIGNATURE-----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=5WN9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.10 merge window
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
Andy Shevchenko