Currently, intel_pstate doesn't register if _PSS is not present on
HP Proliant systems, because it expects the firmware to take over
CPU performance scaling in that case. However, if ACPI PCCH is
present, the firmware expects the kernel to use it for CPU
performance scaling and the pcc-cpufreq driver is loaded for that.
Unfortunately, the firmware interface used by that driver is not
scalable for fundamental reasons, so pcc-cpufreq is way suboptimal
on systems with more than just a few CPUs. In fact, it is better to
avoid using it at all.
For this reason, modify intel_pstate to look for ACPI PCCH if _PSS
is not present and register if it is there. Also prevent the
pcc-cpufreq driver from trying to initialize itself if intel_pstate
has been registered already.
Fixes: fbbcdc0744 (intel_pstate: skip the driver if ACPI has power mgmt option)
Reported-by: Andreas Herrmann <aherrmann@suse.com>
Reviewed-by: Andreas Herrmann <aherrmann@suse.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Andreas Herrmann <aherrmann@suse.com>
Cc: 4.16+ <stable@vger.kernel.org> # 4.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The firmware interface used by the pcc-cpufreq driver is
fundamentally not scalable and using it for dynamic CPU performance
scaling on systems with many CPUs leads to degraded performance.
For this reason, disable dynamic CPU performance scaling on systems
with pcc-cpufreq where the number of CPUs present at the driver init
time is greater than 4. Also make the driver print corresponding
complaints to the kernel log.
Reported-by: Andreas Herrmann <aherrmann@suse.com>
Tested-by: Andreas Herrmann <aherrmann@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If of_nvmem_cell_get() fails due to probe deferal, we shouldn't print an
error message. Just be silent in this case.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Per Section 8.4.7.1.3 of ACPI 6.2, the platform provides performance
feedback via set of performance counters. To determine the actual
performance level delivered over time, OSPM may read a set of
performance counters from the Reference Performance Counter Register
and the Delivered Performance Counter Register.
OSPM calculates the delivered performance over a given time period by
taking a beginning and ending snapshot of both the reference and
delivered performance counters, and calculating:
delivered_perf = reference_perf X (delta of delivered_perf counter / delta of reference_perf counter).
Implement the above and hook this up to the cpufreq->get method.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Armada 37xx supports Adaptive Voltage Scaling and thanks to this patch a
voltage is associated to each load level.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Exynos5440 is not actively developed, there are no development
boards available and probably there are no real products with it.
Remove wide-tree support for Exynos5440.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
POWER9 does not support global pstate requests for the chip. So remove
the timer logic which slowly ramps down the global pstate in P9
platforms.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[mpe: Drop NULL check before kfree(policy->driver_data)]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The cooling device should be part of the i.MX cpufreq driver, but it
cannot be removed for the sake of DT stability. So turn the cooling
device registration into a separate function and perform the
registration only if the CPU OF node does not have the #cooling-cells
property.
Use of_cpufreq_power_cooling_register in imx_thermal code to link the
cooling device to the device tree node provided.
This makes it possible to bind the cpufreq cooling device to a custom
thermal zone via a cooling-maps entry like:
cooling-maps {
map0 {
trip = <&board_alert>;
cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
Assuming a cpu node exists with label "cpu0" and #cooling-cells
property.
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
match_string() returns the index of an array for a matching string,
which can be used instead of open coded variant.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We should return if get_cpu_device() fails or it leads to a NULL
dereference. Also dev_pm_opp_of_get_opp_desc_node() returns NULL on
error, it never returns error pointers.
Fixes: 46e2856b8e (cpufreq: Add Kryo CPU scaling driver)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When scaling max/min settings are changed, internally they are converted
to a ratio using the max turbo 1 core turbo frequency. This works fine
when 1 core max is same irrespective of the core. But under Turbo 3.0,
this will not be the case. For example:
Core 0: max turbo pstate: 43 (4.3GHz)
Core 1: max turbo pstate: 45 (4.5GHz)
In this case 1 core turbo ratio will be maximum of all, so it will be
45 (4.5GHz). Suppose scaling max is set to 4GHz (ratio 40) for all cores
,then on core one it will be
= max_state * policy->max / max_freq;
= 43 * (4000000/4500000) = 38 (3.8GHz)
= 38
which is 200MHz less than the desired.
On core2, it will be correctly set to ratio 40 (4GHz). Same holds true
for scaling min frequency limit. So this requires usage of correct turbo
max frequency for core one, which in this case is 4.3GHz. So we need to
adjust per CPU cpu->pstate.turbo_freq using the maximum HWP ratio of that
core.
This change uses the HWP capability of a core to adjust max turbo
frequency. But since Broadwell HWP doesn't use ratios in the HWP
capabilities, we have to use legacy max 1 core turbo ratio. This is not
a problem as the HWP capabilities don't differ among cores in Broadwell.
We need to check for non Broadwell CPU model for applying this change,
though.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 4.6+ <stable@vger.kernel.org> # 4.6+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add device remove and module exit code to make the driver
functioning as a loadable module.
Fixes: ac28927659 (cpufreq: kryo: allow building as a loadable module)
Signed-off-by: Ilia Lin <ilia.lin@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In event of error returned by the nvmem_cell_read() non-pointer value
may be dereferenced. Fix this with error handling.
Additionally free the allocated speedbin buffer, as per the API.
Fixes: 9ce36edd1a52 (cpufreq: Add Kryo CPU scaling driver)
Signed-off-by: Ilia Lin <ilia.lin@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Revert a recent PM core change that attempted to fix an issue
related to device links, but introduced a regression (Rafael
Wysocki).
- Fix build when the recently added cpufreq driver for Kryo
processors is selected by making it possible to build that
driver as a module (Arnd Bergmann).
- Fix the long idle detection mechanism in the out-of-band
(ondemand and conservative) cpufreq governors (Chen Yu).
- Add support for devices in multiple power domains to the
generic power domains (genpd) framework (Ulf Hansson).
- Add support for iowait boosting on systems with hardware-managed
P-states (HWP) enabled to the intel_pstate driver and make it use
that feature on systems with Skylake Xeon processors as it is
reported to improve performance significantly on those systems
(Srinivas Pandruvada).
- Fix and update the acpi_cpufreq, ti-cpufreq and imx6q cpufreq
drivers (Colin Ian King, Suman Anna, Sébastien Szymanski).
- Change the behavior of the wakeup_count device attribute in
sysfs to expose the number of events when the device might have
aborted system suspend in progress (Ravi Chandra Sadineni).
- Fix two minor issues in the cpupower utility (Abhishek Goel,
Colin Ian King).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=VROk
-----END PGP SIGNATURE-----
Merge tag 'pm-4.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These revert a recent PM core change that introduced a regression, fix
the build when the recently added Kryo cpufreq driver is selected, add
support for devices attached to multiple power domains to the generic
power domains (genpd) framework, add support for iowait boosting on
systens with hardware-managed P-states (HWP) enabled to the
intel_pstate driver, modify the behavior of the wakeup_count device
attribute in sysfs, fix a few issues and clean up some ugliness,
mostly in cpufreq (core and drivers) and in the cpupower utility.
Specifics:
- Revert a recent PM core change that attempted to fix an issue
related to device links, but introduced a regression (Rafael
Wysocki)
- Fix build when the recently added cpufreq driver for Kryo
processors is selected by making it possible to build that driver
as a module (Arnd Bergmann)
- Fix the long idle detection mechanism in the out-of-band (ondemand
and conservative) cpufreq governors (Chen Yu)
- Add support for devices in multiple power domains to the generic
power domains (genpd) framework (Ulf Hansson)
- Add support for iowait boosting on systems with hardware-managed
P-states (HWP) enabled to the intel_pstate driver and make it use
that feature on systems with Skylake Xeon processors as it is
reported to improve performance significantly on those systems
(Srinivas Pandruvada)
- Fix and update the acpi_cpufreq, ti-cpufreq and imx6q cpufreq
drivers (Colin Ian King, Suman Anna, Sébastien Szymanski)
- Change the behavior of the wakeup_count device attribute in sysfs
to expose the number of events when the device might have aborted
system suspend in progress (Ravi Chandra Sadineni)
- Fix two minor issues in the cpupower utility (Abhishek Goel, Colin
Ian King)"
* tag 'pm-4.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "PM / runtime: Fixup reference counting of device link suppliers at probe"
cpufreq: imx6q: check speed grades for i.MX6ULL
cpufreq: governors: Fix long idle detection logic in load calculation
cpufreq: intel_pstate: enable boost for Skylake Xeon
PM / wakeup: Export wakeup_count instead of event_count via sysfs
PM / Domains: Add dev_pm_domain_attach_by_id() to manage multi PM domains
PM / Domains: Add support for multi PM domains per device to genpd
PM / Domains: Split genpd_dev_pm_attach()
PM / Domains: Don't attach devices in genpd with multi PM domains
PM / Domains: dt: Allow power-domain property to be a list of specifiers
cpufreq: intel_pstate: New sysfs entry to control HWP boost
cpufreq: intel_pstate: HWP boost performance on IO wakeup
cpufreq: intel_pstate: Add HWP boost utility and sched util hooks
cpufreq: ti-cpufreq: Use devres managed API in probe()
cpufreq: ti-cpufreq: Fix an incorrect error return value
cpufreq: ACPI: make function acpi_cpufreq_fast_switch() static
cpufreq: kryo: allow building as a loadable module
cpupower : Fix header name to read idle state name
cpupower: fix spelling mistake: "logilename" -> "logfilename"
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed (Kees)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=zUUp
-----END PGP SIGNATURE-----
Merge tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull more overflow updates from Kees Cook:
"The rest of the overflow changes for v4.18-rc1.
This includes the explicit overflow fixes from Silvio, further
struct_size() conversions from Matthew, and a bug fix from Dan.
But the bulk of it is the treewide conversions to use either the
2-factor argument allocators (e.g. kmalloc(a * b, ...) into
kmalloc_array(a, b, ...) or the array_size() macros (e.g. vmalloc(a *
b) into vmalloc(array_size(a, b)).
Coccinelle was fighting me on several fronts, so I've done a bunch of
manual whitespace updates in the patches as well.
Summary:
- Error path bug fix for overflow tests (Dan)
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed
(Kees)"
* tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (26 commits)
treewide: Use array_size in f2fs_kvzalloc()
treewide: Use array_size() in f2fs_kzalloc()
treewide: Use array_size() in f2fs_kmalloc()
treewide: Use array_size() in sock_kmalloc()
treewide: Use array_size() in kvzalloc_node()
treewide: Use array_size() in vzalloc_node()
treewide: Use array_size() in vzalloc()
treewide: Use array_size() in vmalloc()
treewide: devm_kzalloc() -> devm_kcalloc()
treewide: devm_kmalloc() -> devm_kmalloc_array()
treewide: kvzalloc() -> kvcalloc()
treewide: kvmalloc() -> kvmalloc_array()
treewide: kzalloc_node() -> kcalloc_node()
treewide: kzalloc() -> kcalloc()
treewide: kmalloc() -> kmalloc_array()
mm: Introduce kvcalloc()
video: uvesafb: Fix integer overflow in allocation
UBIFS: Fix potential integer overflow in allocation
leds: Use struct_size() in allocation
Convert intel uncore to struct_size
...
This branch contains platform-related driver updates for ARM and ARM64.
Highlights:
- ARM SCMI (System Control & Management Interface) driver cleanups
- Hisilicon support for LPC bus w/ ACPI
- Reset driver updates for several platforms: Uniphier,
- Rockchip power domain bindings and hardware descriptions for several SoCs.
- Tegra memory controller reset improvements
-----BEGIN PGP SIGNATURE-----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=xs+f
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"This contains platform-related driver updates for ARM and ARM64.
Highlights:
- ARM SCMI (System Control & Management Interface) driver cleanups
- Hisilicon support for LPC bus w/ ACPI
- Reset driver updates for several platforms: Uniphier,
- Rockchip power domain bindings and hardware descriptions for
several SoCs.
- Tegra memory controller reset improvements"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (59 commits)
ARM: tegra: fix compile-testing PCI host driver
soc: rockchip: power-domain: add power domain support for px30
dt-bindings: power: add binding for px30 power domains
dt-bindings: power: add PX30 SoCs header for power-domain
soc: rockchip: power-domain: add power domain support for rk3228
dt-bindings: power: add binding for rk3228 power domains
dt-bindings: power: add RK3228 SoCs header for power-domain
soc: rockchip: power-domain: add power domain support for rk3128
dt-bindings: power: add binding for rk3128 power domains
dt-bindings: power: add RK3128 SoCs header for power-domain
soc: rockchip: power-domain: add power domain support for rk3036
dt-bindings: power: add binding for rk3036 power domains
dt-bindings: power: add RK3036 SoCs header for power-domain
dt-bindings: memory: tegra: Remove Tegra114 SATA and AFI reset definitions
memory: tegra: Remove Tegra114 SATA and AFI reset definitions
memory: tegra: Register SMMU after MC driver became ready
soc: mediatek: remove unneeded semicolon
soc: mediatek: add a fixed wait for SRAM stable
soc: mediatek: introduce a CAPS flag for scp_domain_data
soc: mediatek: reuse regmap_read_poll_timeout helpers
...
Check the max speed supported from the fuses for i.MX6ULL and update the
operating points table accordingly.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
According to current code implementation, detecting the long
idle period is done by checking if the interval between two
adjacent utilization update handlers is long enough. Although
this mechanism can detect if the idle period is long enough
(no utilization hooks invoked during idle period), it might
not cover a corner case: if the task has occupied the CPU
for too long which causes no context switches during that
period, then no utilization handler will be launched until this
high prio task is scheduled out. As a result, the idle_periods
field might be calculated incorrectly because it regards the
100% load as 0% and makes the conservative governor who uses
this field confusing.
Change the detection to compare the idle_time with sampling_rate
directly.
Reported-by: Artem S. Tashkinov <t.artem@mailcity.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Enable HWP boost on Skylake server and workstations.
Reported-by: Mel Gorman <mgorman@techsingularity.net>
Tested-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A new attribute is added to intel_pstate sysfs to enable/disable
HWP dynamic performance boost.
Reported-by: Mel Gorman <mgorman@techsingularity.net>
Tested-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This change uses SCHED_CPUFREQ_IOWAIT flag to boost HWP performance.
Since SCHED_CPUFREQ_IOWAIT flag is set frequently, we don't start
boosting steps unless we see two consecutive flags in two ticks. This
avoids boosting due to IO because of regular system activities.
To avoid synchronization issues, the actual processing of the flag is
done on the local CPU callback.
Reported-by: Mel Gorman <mgorman@techsingularity.net>
Tested-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Added two utility functions to HWP boost up gradually and boost down to
the default cached HWP request values.
Boost up:
Boost up updates HWP request minimum value in steps. This minimum value
can reach upto at HWP request maximum values depends on how frequently,
this boost up function is called. At max, boost up will take three steps
to reach the maximum, depending on the current HWP request levels and HWP
capabilities. For example, if the current settings are:
If P0 (Turbo max) = P1 (Guaranteed max) = min
No boost at all.
If P0 (Turbo max) > P1 (Guaranteed max) = min
Should result in one level boost only for P0.
If P0 (Turbo max) = P1 (Guaranteed max) > min
Should result in two level boost:
(min + p1)/2 and P1.
If P0 (Turbo max) > P1 (Guaranteed max) > min
Should result in three level boost:
(min + p1)/2, P1 and P0.
We don't set any level between P0 and P1 as there is no guarantee that
they will be honored.
Boost down:
After the system is idle for hold time of 3ms, the HWP request is reset
to the default value from HWP init or user modified one via sysfs.
Caching of HWP Request and Capabilities
Store the HWP request value last set using MSR_HWP_REQUEST and read
MSR_HWP_CAPABILITIES. This avoid reading of MSRs in the boost utility
functions.
These boost utility functions calculated limits are based on the latest
HWP request value, which can be modified by setpolicy() callback. So if
user space modifies the minimum perf value, that will be accounted for
every time the boost up is called. There will be case when there can be
contention with the user modified minimum perf, in that case user value
will gain precedence. For example just before HWP_REQUEST MSR is updated
from setpolicy() callback, the boost up function is called via scheduler
tick callback. Here the cached MSR value is already the latest and limits
are updated based on the latest user limits, but on return the MSR write
callback called from setpolicy() callback will update the HWP_REQUEST
value. This will be used till next time the boost up function is called.
In addition add a variable to control HWP dynamic boosting. When HWP
dynamic boost is active then set the HWP specific update util hook. The
contents in the utility hooks will be filled in the subsequent patches.
Reported-by: Mel Gorman <mgorman@techsingularity.net>
Tested-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ti_cpufreq_probe() function uses regular kzalloc to allocate
the ti_cpufreq_data structure and kfree for freeing this memory
on failures. Simplify this code by using the devres managed
API.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 05829d9431 (cpufreq: ti-cpufreq: kfree opp_data when
failure) has fixed a memory leak in the failure path, however
the patch returned a positive value on get_cpu_device() failure
instead of the previous negative value. Fix this incorrect error
return value properly.
Fixes: 05829d9431 (cpufreq: ti-cpufreq: kfree opp_data when failure)
Cc: 4.14+ <stable@vger.kernel.org> # v4.14+
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The acpi_cpufreq_fast_switch() function is local to the source and
does not need to be in global scope, so make it static.
Cleans up sparse warning:
drivers/cpufreq/acpi-cpufreq.c:468:14: warning: symbol
'acpi_cpufreq_fast_switch' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Building the kryo cpufreq driver while QCOM_SMEM is a loadable module
results in a link error:
drivers/cpufreq/qcom-cpufreq-kryo.o: In function `qcom_cpufreq_kryo_probe':
qcom-cpufreq-kryo.c:(.text+0xbc): undefined reference to `qcom_smem_get'
The problem is that Kconfig ignores interprets the dependency as met
when the dependent symbol is a 'bool' one. By making it 'tristate',
it will be forced to be a module here, which builds successfully.
Fixes: 46e2856b8e (cpufreq: Add Kryo CPU scaling driver)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These update the ACPICA code in the kernel to the 20180508 upstream
revision and make it support the RT patch, add CPPC v3 support to the
ACPI CPPC library, add a WDAT-based watchdog quirk to prevent clashes
with the RTC, add quirks to the ACPI AC and battery drivers, and
update the ACPI SoC drivers.
Specifics:
- Update the ACPICA code in the kernel to the 20180508 upstream
revision including:
* iASL -tc option enhancement (Bob Moore).
* Debugger improvements (Bob Moore).
* Support for tables larger than 1 MB in acpidump/acpixtract
(Bob Moore).
* Minor fixes and cleanups (Colin Ian King, Toomas Soome).
- Make the ACPICA code in the kernel support the RT patch (Sebastian
Andrzej Siewior, Steven Rostedt).
- Add a kmemleak annotation to the ACPICA code (Larry Finger).
- Add CPPC v3 support to the ACPI CPPC library and fix two issues
related to CPPC (Prashanth Prakash, Al Stone).
- Add an ACPI WDAT-based watchdog quirk to prefer iTCO_wdt on
systems where WDAT clashes with the RTC SRAM (Mika Westerberg).
- Add some quirks to the ACPI AC and battery drivers (Carlo Caione,
Hans de Goede).
- Update the ACPI SoC drivers for Intel (LPSS) and AMD (APD)
platforms (Akshu Agrawal, Hans de Goede).
- Fix up some assorted minor issues (Al Stone, Laszlo Toth,
Mathieu Malaterre).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=FAIF
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to the 20180508 upstream
revision and make it support the RT patch, add CPPC v3 support to the
ACPI CPPC library, add a WDAT-based watchdog quirk to prevent clashes
with the RTC, add quirks to the ACPI AC and battery drivers, and
update the ACPI SoC drivers.
Specifics:
- Update the ACPICA code in the kernel to the 20180508 upstream
revision including:
* iASL -tc option enhancement (Bob Moore).
* Debugger improvements (Bob Moore).
* Support for tables larger than 1 MB in acpidump/acpixtract (Bob
Moore).
* Minor fixes and cleanups (Colin Ian King, Toomas Soome).
- Make the ACPICA code in the kernel support the RT patch (Sebastian
Andrzej Siewior, Steven Rostedt).
- Add a kmemleak annotation to the ACPICA code (Larry Finger).
- Add CPPC v3 support to the ACPI CPPC library and fix two issues
related to CPPC (Prashanth Prakash, Al Stone).
- Add an ACPI WDAT-based watchdog quirk to prefer iTCO_wdt on systems
where WDAT clashes with the RTC SRAM (Mika Westerberg).
- Add some quirks to the ACPI AC and battery drivers (Carlo Caione,
Hans de Goede).
- Update the ACPI SoC drivers for Intel (LPSS) and AMD (APD)
platforms (Akshu Agrawal, Hans de Goede).
- Fix up some assorted minor issues (Al Stone, Laszlo Toth, Mathieu
Malaterre)"
* tag 'acpi-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
ACPICA: Mark acpi_ut_create_internal_object_dbg() memory allocations as non-leaks
ACPI / watchdog: Prefer iTCO_wdt always when WDAT table uses RTC SRAM
mailbox: PCC: erroneous error message when parsing ACPI PCCT
ACPICA: Update version to 20180508
ACPICA: acpidump/acpixtract: Support for tables larger than 1MB
ACPI: APD: Add AMD misc clock handler support
clk: x86: Add ST oscout platform clock
ACPICA: Update version to 20180427
ACPICA: Debugger: Removed direct support for EC address space in "Test Objects"
ACPICA: Debugger: Add Package support for "test objects" command
ACPICA: Improve error messages for the namespace root node
ACPICA: Fix potential infinite loop in acpi_rs_dump_byte_list
ACPICA: vsnprintf: this statement may fall through
ACPICA: Tables: Fix spelling mistake in comment
ACPICA: iASL: Enhance the -tc option (create AML hex file in C)
ACPI: Add missing prototype_for arch_post_acpi_subsys_init()
ACPI / tables: improve comments regarding acpi_parse_entries_array()
ACPICA: Convert acpi_gbl_hardware lock back to an acpi_raw_spinlock
ACPICA: provide abstraction for raw_spinlock_t
ACPI / CPPC: Fix invalid PCC channel status errors
...
* acpi-cppc:
mailbox: PCC: erroneous error message when parsing ACPI PCCT
ACPI / CPPC: Fix invalid PCC channel status errors
ACPI / CPPC: Document CPPC sysfs interface
cpufreq / CPPC: Support for CPPC v3
ACPI / CPPC: Check for valid PCC subspace only if PCC is used
ACPI / CPPC: Add support for CPPC v3
* acpi-misc:
ACPI: Add missing prototype_for arch_post_acpi_subsys_init()
ACPI: add missing newline to printk
* acpi-battery:
ACPI / battery: Add quirk to avoid checking for PMIC with native driver
ACPI / battery: Ignore AC state in handle_discharging on systems where it is broken
ACPI / battery: Add handling for devices which wrongly report discharging state
ACPI / battery: Remove initializer for unused ident dmi_system_id
ACPI / AC: Remove initializer for unused ident dmi_system_id
* acpi-ac:
ACPI / AC: Add quirk to avoid checking for PMIC with native driver
In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO processors,
the CPU frequency subset and voltage value of each OPP varies
based on the silicon variant in use. Qualcomm Process Voltage Scaling Tables
defines the voltage and frequency value based on the msm-id in SMEM
and speedbin blown in the efuse combination.
The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
to provide the OPP framework with required information.
This is used to determine the voltage and frequency value for each OPP of
operating-points-v2 table when it is parsed by the OPP framework.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use the static SRCU initializer for `cpufreq_transition_notifier_list'.
This avoids the init_cpufreq_transition_notifier_list() initcall. Its
only purpose is to initialize the SRCU notifier once during boot and set
another variable which is used as an indicator whether the init was
perfromed before cpufreq_register_notifier() was used.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the policy limits are updated via cpufreq_update_policy() and
subsequently via sysfs, the limits stored in user_policy may be
set incorrectly.
For example, if both min and max are set via sysfs to the maximum
available frequency, user_policy.min and user_policy.max will also
be the maximum. If a policy notifier triggered by
cpufreq_update_policy() lowers both the min and the max at this
point, that change is not reflected by the user_policy limits, so
if the max is updated again via sysfs to the same lower value,
then user_policy.max will be lower than user_policy.min which
shouldn't happen. In particular, if one of the policy CPUs is
then taken offline and back online, cpufreq_set_policy() will
fail for it due to a failing limits check.
To prevent that from happening, initialize the min and max fields
of the new_policy object to the ones stored in user_policy that
were previously set via sysfs.
Signed-off-by: Kevin Wangtao <kevin.wangtao@hisilicon.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Subject & changelog ]
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This routine checks if the CPU running this code belongs to the policy
of the target CPU or if not, can it do remote DVFS for it remotely. But
the current name of it implies as if it is only about doing remote
updates.
Rename it to make it more relevant.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently tegra20-cpufreq kernel module isn't getting autoloaded because
there is no device associated with the module, this is one of two patches
that resolves the module autoloading. This patch adds a module alias that
will associate the tegra20-cpufreq kernel module with the platform device,
other patch will instantiate the actual platform device. And now it makes
sense to wrap cpufreq driver into a platform driver for consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Nothing prevents Tegra20 CPUFreq module to be unloaded, hence allow it to
be built as a non-builtin kernel module.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Don't even try to request the clocks during of module initialization on
non-Tegra20 machines (this is the case for a multi-platform kernel) for
consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove checking of the CPU number for consistency as it won't ever fail
unless there is a severe bug in the cpufreq core.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The EMC driver has been gone 4 years ago, since the commit a7cbe92cef
("ARM: tegra: remove tegra EMC scaling driver"). Remove the EMC clock
usage as it does nothing. We may consider re-implementing the EMC scaling
later, probably using PM Memory Bandwidth QoS API.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove unused/unneeded headers and sort them in the alphabet order.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove unneeded blank line and replace whitespaces with a tab in the code
for consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Change module description to be in line with the other Tegra drivers, just
for consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This contains all of the trivial review comments that were not
addressed as the series was already queued up for v4.17 and were not
critical to go as fixes.
They generally just improve code readability, fix kernel-docs, remove
unused/unnecessary code, follow standard function naming and simplifies
certain exit paths.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OzDu
-----END PGP SIGNATURE-----
Merge tag 'scmi-updates-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers
SCMI cleanups for v4.18
This contains all of the trivial review comments that were not
addressed as the series was already queued up for v4.17 and were not
critical to go as fixes.
They generally just improve code readability, fix kernel-docs, remove
unused/unnecessary code, follow standard function naming and simplifies
certain exit paths.
* tag 'scmi-updates-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: simplify exit path by returning on error
firmware: arm_scmi: improve exit paths and code readability
firmware: arm_scmi: remove unnecessary bitmap_zero
firmware: arm_scmi: drop unused `con_priv` structure member
firmware: arm_scmi: rename scmi_xfer_{init,get,put}
firmware: arm_scmi: rename get_transition_latency and add_opps_to_device
firmware: arm_scmi: fix kernel-docs documentation
firmware: arm_scmi: improve code readability using bitfield accessor macros
Signed-off-by: Olof Johansson <olof@lixom.net>
This reverts commit 034def597b.
This is no longer needed since the following commit and to the best
of my knowledge is not relied on by any upstream DTS:
edeec420de (cpufreq: dt-platdev: Automatically create cpufreq
device with OPP v2)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit bea2ebca6b.
This is no longer needed since the following commit and to the best
of my knowledge is not relied on by any upstream DTS:
edeec420de (cpufreq: dt-platdev: Automatically create cpufreq
device with OPP v2)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Allow use of the trace_pstate_sample trace function
when the intel_pstate driver is in passive mode.
Since the core_busy and scaled_busy fields are not
used, and it might be desirable to know which path
through the driver was used, either intel_cpufreq_target
or intel_cpufreq_fast_switch, re-task the core_busy
field as a flag indicator.
The user can then use the intel_pstate_tracer.py utility
to summarize and plot the trace.
Note: The core_busy feild still goes by that name
in include/trace/events/power.h and within the
intel_pstate_tracer.py script and csv file headers,
but it is graphed as "performance", and called
core_avg_perf now in the intel_pstate driver.
Sometimes, in passive mode, the driver is not called for
many tens or even hundreds of seconds. The user
needs to understand, and not be confused by, this limitation.
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Armada-37xx driver registers a cpufreq-dt driver. Not having
CONFIG_CPUFREQ_DT selected leads to a silent abort during the probe.
Prevent that situation by having the former depending on the latter.
Fixes: 92ce45fb87 (cpufreq: Add DVFS support for Armada 37xx)
Cc: 4.16+ <stable@vger.kernel.org> # 4.16+
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_notify_transition() calls __cpufreq_notify_transition() for each
CPU of a policy. There is a lot of code in __cpufreq_notify_transition()
though which isn't required to be executed for each CPU, like checking
about disabled cpufreq or irqs, adjusting jiffies, updating cpufreq
stats and some debug print messages.
This commit merges __cpufreq_notify_transition() into
cpufreq_notify_transition() and modifies cpufreq_notify_transition() to
execute minimum amount of code for each CPU.
Also fix the kerneldoc for cpufreq_notify_transition() while at it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Trivial fix to spelling mistake in s3c_freq_dbg debug message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the scmi code follows the suggestion from Greg KH on a totally
different thread[0] to have the subsystem name first, followed by the
noun and finally the verb with couple of these exceptions.
This patch fixes them so that all the functions names are aligned to
that practice.
[0] https://www.spinics.net/lists/arm-kernel/msg583673.html
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
speedstep_detect_processor() is declared as returing an
'enum speedstep_processor' but use an 'int' in its definition.
Fix this by using 'enum speedstep_processor' in its definition too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add suspend/resume hooks in Armada 37xx DVFS driver to handle S2RAM
operations. As there is currently no 'driver' structure, create one
to store both the regmap and the register values during suspend
operation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The resources weren't freed on failures, free them properly.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Platforms may need to implement platform specific suspend/resume hooks.
Update cpufreq-dt driver's platform data to contain those for such
platforms.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support to specify platform specific transition_delay_us instead
of using the transition delay derived from PCC.
With commit 3d41386d55 (cpufreq: CPPC: Use transition_delay_us
depending transition_latency) we are setting transition_delay_us
directly and not applying the LATENCY_MULTIPLIER. Because of that,
on Qualcomm Centriq we can end up with a very high rate of frequency
change requests when using the schedutil governor (default
rate_limit_us=10 compared to an earlier value of 10000).
The PCC subspace describes the rate at which the platform can accept
commands on the CPPC's PCC channel. This includes read and write
command on the PCC channel that can be used for reasons other than
frequency transitions. Moreover the same PCC subspace can be used by
multiple freq domains and deriving transition_delay_us from it as we
do now can be sub-optimal.
Moreover if a platform does not use PCC for desired_perf register then
there is no way to compute the transition latency or the delay_us.
CPPC does not have a standard defined mechanism to get the transition
rate or the latency at the moment.
Given the above limitations, it is simpler to have a platform specific
transition_delay_us and rely on PCC derived value only if a platform
specific value is not available.
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Fixes: 3d41386d55 (cpufreq: CPPC: Use transition_delay_us depending transition_latency)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A bunch of fixes, mostly for existing code and going to stable.
Our memory hot-unplug path wasn't flushing the cache before removing memory.
That is a problem now that we are doing memory hotplug on bare metal.
Three fixes for the NPU code that supports devices connected via NVLink (ie.
GPUs). The main one tweaks the TLB flush algorithm to avoid soft lockups for
large flushes.
A fix for our memory error handling where we would loop infinitely, returning
back to the bad access and hard lockup the CPU.
Fixes for the OPAL RTC driver, which wasn't handling some error cases correctly.
A fix for a hardlockup in the powernv cpufreq driver.
And finally two fixes to our smp_send_stop(), required due to a recent change to
use it on shutdown.
Thanks to:
Alistair Popple, Balbir Singh, Laurentiu Tudor, Mahesh Salgaonkar, Mark
Hairgrove, Nicholas Piggin, Rashmica Gupta, Shilpasri G Bhat.
-----BEGIN PGP SIGNATURE-----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=JJLB
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.17-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A bunch of fixes, mostly for existing code and going to stable.
Our memory hot-unplug path wasn't flushing the cache before removing
memory. That is a problem now that we are doing memory hotplug on bare
metal.
Three fixes for the NPU code that supports devices connected via
NVLink (ie. GPUs). The main one tweaks the TLB flush algorithm to
avoid soft lockups for large flushes.
A fix for our memory error handling where we would loop infinitely,
returning back to the bad access and hard lockup the CPU.
Fixes for the OPAL RTC driver, which wasn't handling some error cases
correctly.
A fix for a hardlockup in the powernv cpufreq driver.
And finally two fixes to our smp_send_stop(), required due to a recent
change to use it on shutdown.
Thanks to: Alistair Popple, Balbir Singh, Laurentiu Tudor, Mahesh
Salgaonkar, Mark Hairgrove, Nicholas Piggin, Rashmica Gupta, Shilpasri
G Bhat"
* tag 'powerpc-4.17-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/kvm/booke: Fix altivec related build break
powerpc: Fix deadlock with multiple calls to smp_send_stop
cpufreq: powernv: Fix hardlockup due to synchronous smp_call in timer interrupt
powerpc: Fix smp_send_stop NMI IPI handling
rtc: opal: Fix OPAL RTC driver OPAL_BUSY loops
powerpc/mce: Fix a bug where mce loops on memory UE.
powerpc/powernv/npu: Do a PID GPU TLB flush when invalidating a large address range
powerpc/powernv/npu: Prevent overwriting of pnv_npu2_init_contex() callback parameters
powerpc/powernv/npu: Add lock to prevent race in concurrent context init/destroy
powerpc/powernv/memtrace: Let the arch hotunplug code flush cache
powerpc/mm: Flush cache on memory hot(un)plug
gpstate_timer_handler() uses synchronous smp_call to set the pstate
on the requested core. This causes the below hard lockup:
smp_call_function_single+0x110/0x180 (unreliable)
smp_call_function_any+0x180/0x250
gpstate_timer_handler+0x1e8/0x580
call_timer_fn+0x50/0x1c0
expire_timers+0x138/0x1f0
run_timer_softirq+0x1e8/0x270
__do_softirq+0x158/0x3e4
irq_exit+0xe8/0x120
timer_interrupt+0x9c/0xe0
decrementer_common+0x114/0x120
-- interrupt: 901 at doorbell_global_ipi+0x34/0x50
LR = arch_send_call_function_ipi_mask+0x120/0x130
arch_send_call_function_ipi_mask+0x4c/0x130
smp_call_function_many+0x340/0x450
pmdp_invalidate+0x98/0xe0
change_huge_pmd+0xe0/0x270
change_protection_range+0xb88/0xe40
mprotect_fixup+0x140/0x340
SyS_mprotect+0x1b4/0x350
system_call+0x58/0x6c
One way to avoid this is removing the smp-call. We can ensure that the
timer always runs on one of the policy-cpus. If the timer gets
migrated to a cpu outside the policy then re-queue it back on the
policy->cpus. This way we can get rid of the smp-call which was being
used to set the pstate on the policy->cpus.
Fixes: 7bc54b652f ("timers, cpufreq/powernv: Initialize the gpstate timer as pinned")
Cc: stable@vger.kernel.org # v4.8+
Reported-by: Nicholas Piggin <npiggin@gmail.com>
Reported-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use CPPC v3 entries to convert the abstract processor performance to
processor frequency in KHz.
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This debug code was helpful while developing the driver, but it isn't
being used for anything anymore.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This isn't used anymore. Remove the helper and update documentation
accordingly.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from SCMI driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When multiple CPUs are related in one cpufreq policy, the first online
CPU will be chosen by default to handle cpufreq operations. Let's take
cpu0 and cpu1 as an example.
When cpu0 is offline, policy->cpu will be shifted to cpu1. cpu1's perf
capabilities should be initialized. Otherwise, perf capabilities are 0s
and speed change can not take effect.
This patch copies perf capabilities of the first online CPU to other
shared CPUs when policy shared type is CPUFREQ_SHARED_TYPE_ANY.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shunyong Yang <shunyong.yang@hxt-semitech.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There was no clk_put() balancing the clk_get(). This commit fixes it.
Fixes: 92ce45fb87 (cpufreq: Add DVFS support for Armada 37xx)
Cc: 4.16+ <stable@vger.kernel.org> # 4.16+
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that the driver has started to set transition_delay_us directly,
there is no need to set transition_latency along with it, as it is not
used by the cpufreq core.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This driver can not be built as a module and there is no need of the
platform driver unregister part. Use builtin_platform_driver() instead
of module_platform_driver().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The intel_pstate driver doesn't use debugfs any more, so drop
linux/debugfs.h from the list of included headers in it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The main addition this time around is the new ARM "SCMI" framework,
which is the latest in a series of standards coming from ARM to do power
management in a platform independent way. This has been through many
review cycles, and it relies on a rather interesting way of using the
mailbox subsystem, but in the end I agreed that Sudeep's version was
the best we could do after all.
Other changes include:
- the ARM CCN driver is moved out of drivers/bus into drivers/perf,
which makes more sense. Similarly, the performance monitoring
portion of the CCI driver are moved the same way and cleaned up
a little more.
- a series of updates to the SCPI framework
- support for the Mediatek mt7623a SoC in drivers/soc
- support for additional NVIDIA Tegra hardware in drivers/soc
- a new reset driver for Socionext Uniphier
- lesser bug fixes in drivers/soc, drivers/tee, drivers/memory, and
drivers/firmware and drivers/reset across platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Pmsx
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The main addition this time around is the new ARM "SCMI" framework,
which is the latest in a series of standards coming from ARM to do
power management in a platform independent way.
This has been through many review cycles, and it relies on a rather
interesting way of using the mailbox subsystem, but in the end I
agreed that Sudeep's version was the best we could do after all.
Other changes include:
- the ARM CCN driver is moved out of drivers/bus into drivers/perf,
which makes more sense. Similarly, the performance monitoring
portion of the CCI driver are moved the same way and cleaned up a
little more.
- a series of updates to the SCPI framework
- support for the Mediatek mt7623a SoC in drivers/soc
- support for additional NVIDIA Tegra hardware in drivers/soc
- a new reset driver for Socionext Uniphier
- lesser bug fixes in drivers/soc, drivers/tee, drivers/memory, and
drivers/firmware and drivers/reset across platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (87 commits)
reset: uniphier: add ethernet reset control support for PXs3
reset: stm32mp1: Enable stm32mp1 reset driver
dt-bindings: reset: add STM32MP1 resets
reset: uniphier: add Pro4/Pro5/PXs2 audio systems reset control
reset: imx7: add 'depends on HAS_IOMEM' to fix unmet dependency
reset: modify the way reset lookup works for board files
reset: add support for non-DT systems
clk: scmi: use devm_of_clk_add_hw_provider() API and drop scmi_clocks_remove
firmware: arm_scmi: prevent accessing rate_discrete uninitialized
hwmon: (scmi) return -EINVAL when sensor information is unavailable
amlogic: meson-gx-socinfo: Update soc ids
soc/tegra: pmc: Use the new reset APIs to manage reset controllers
soc: mediatek: update power domain data of MT2712
dt-bindings: soc: update MT2712 power dt-bindings
cpufreq: scmi: add thermal dependency
soc: mediatek: fix the mistaken pointer accessed when subdomains are added
soc: mediatek: add SCPSYS power domain driver for MediaTek MT7623A SoC
soc: mediatek: avoid hardcoded value with bus_prot_mask
dt-bindings: soc: add header files required for MT7623A SCPSYS dt-binding
dt-bindings: soc: add SCPSYS binding for MT7623 and MT7623A SoC
...
- Modify the cpuidle poll state implementation to prevent CPUs from
staying in the loop in there for excessive times (Rafael Wysocki).
- Add Intel Cannon Lake chips support to the RAPL power capping
driver (Joe Konno).
- Add reference counting to the device links handling code in the
PM core (Lukas Wunner).
- Avoid reconfiguring GPEs on suspend-to-idle in the ACPI system
suspend code (Rafael Wysocki).
- Allow devices to be put into deeper low-power states via ACPI
if both _SxD and _SxW are missing (Daniel Drake).
- Reorganize the core ACPI suspend-to-idle wakeup code to avoid a
keyboard wakeup issue on Asus UX331UA (Chris Chiu).
- Prevent the PCMCIA library code from aborting suspend-to-idle due
to noirq suspend failures resulting from incorrect assumptions
(Rafael Wysocki).
- Add coupled cpuidle supprt to the Exynos3250 platform (Marek
Szyprowski).
- Add new sysfs file to make it easier to specify the image storage
location during hibernation (Mario Limonciello).
- Add sysfs files for collecting suspend-to-idle usage and time
statistics for CPU idle states (Rafael Wysocki).
- Update the pm-graph utilities (Todd Brandt).
- Reduce the kernel log noise related to reporting Low-power Idle
constraings by the ACPI system suspend code (Rafael Wysocki).
- Make it easier to distinguish dedicated wakeup IRQs in the
/proc/interrupts output (Tony Lindgren).
- Add the frequency table validation in cpufreq to the core and
drop it from a number of cpufreq drivers (Viresh Kumar).
- Drop "cooling-{min|max}-level" for CPU nodes from a couple of
DT bindings (Viresh Kumar).
- Clean up the CPU online error code path in the cpufreq core
(Viresh Kumar).
- Fix assorted issues in the SCPI, CPPC, mediatek and tegra186
cpufreq drivers (Arnd Bergmann, Chunyu Hu, George Cherian,
Viresh Kumar).
- Drop memory allocation error messages from a few places in
cpufreq and cpuildle drivers (Markus Elfring).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6JC2
-----END PGP SIGNATURE-----
Merge tag 'pm-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update the cpuidle poll state definition to reduce excessive
energy usage related to it, add new CPU ID to the RAPL power capping
driver, update the ACPI system suspend code to handle some special
cases better, extend the PM core's device links code slightly, add new
sysfs attribute for better suspend-to-idle diagnostics and easier
hibernation handling, update power management tools and clean up
cpufreq quite a bit.
Specifics:
- Modify the cpuidle poll state implementation to prevent CPUs from
staying in the loop in there for excessive times (Rafael Wysocki).
- Add Intel Cannon Lake chips support to the RAPL power capping
driver (Joe Konno).
- Add reference counting to the device links handling code in the PM
core (Lukas Wunner).
- Avoid reconfiguring GPEs on suspend-to-idle in the ACPI system
suspend code (Rafael Wysocki).
- Allow devices to be put into deeper low-power states via ACPI if
both _SxD and _SxW are missing (Daniel Drake).
- Reorganize the core ACPI suspend-to-idle wakeup code to avoid a
keyboard wakeup issue on Asus UX331UA (Chris Chiu).
- Prevent the PCMCIA library code from aborting suspend-to-idle due
to noirq suspend failures resulting from incorrect assumptions
(Rafael Wysocki).
- Add coupled cpuidle supprt to the Exynos3250 platform (Marek
Szyprowski).
- Add new sysfs file to make it easier to specify the image storage
location during hibernation (Mario Limonciello).
- Add sysfs files for collecting suspend-to-idle usage and time
statistics for CPU idle states (Rafael Wysocki).
- Update the pm-graph utilities (Todd Brandt).
- Reduce the kernel log noise related to reporting Low-power Idle
constraings by the ACPI system suspend code (Rafael Wysocki).
- Make it easier to distinguish dedicated wakeup IRQs in the
/proc/interrupts output (Tony Lindgren).
- Add the frequency table validation in cpufreq to the core and drop
it from a number of cpufreq drivers (Viresh Kumar).
- Drop "cooling-{min|max}-level" for CPU nodes from a couple of DT
bindings (Viresh Kumar).
- Clean up the CPU online error code path in the cpufreq core (Viresh
Kumar).
- Fix assorted issues in the SCPI, CPPC, mediatek and tegra186
cpufreq drivers (Arnd Bergmann, Chunyu Hu, George Cherian, Viresh
Kumar).
- Drop memory allocation error messages from a few places in cpufreq
and cpuildle drivers (Markus Elfring)"
* tag 'pm-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (56 commits)
ACPI / PM: Fix keyboard wakeup from suspend-to-idle on ASUS UX331UA
cpufreq: CPPC: Use transition_delay_us depending transition_latency
PM / hibernate: Change message when writing to /sys/power/resume
PM / hibernate: Make passing hibernate offsets more friendly
cpuidle: poll_state: Avoid invoking local_clock() too often
PM: cpuidle/suspend: Add s2idle usage and time state attributes
cpuidle: Enable coupled cpuidle support on Exynos3250 platform
cpuidle: poll_state: Add time limit to poll_idle()
cpufreq: tegra186: Don't validate the frequency table twice
cpufreq: speedstep: Don't validate the frequency table twice
cpufreq: sparc: Don't validate the frequency table twice
cpufreq: sh: Don't validate the frequency table twice
cpufreq: sfi: Don't validate the frequency table twice
cpufreq: scpi: Don't validate the frequency table twice
cpufreq: sc520: Don't validate the frequency table twice
cpufreq: s3c24xx: Don't validate the frequency table twice
cpufreq: qoirq: Don't validate the frequency table twice
cpufreq: pxa: Don't validate the frequency table twice
cpufreq: ppc_cbe: Don't validate the frequency table twice
cpufreq: powernow: Don't validate the frequency table twice
...
With commit e948bc8fbe (cpufreq: Cap the default transition delay
value to 10 ms) the cpufreq was not honouring the delay passed via
ACPI (PCCT). Due to which on ARM based platforms using CPPC the
cpufreq governor tries to change the frequency of CPUs faster than
expected.
This leads to continuous error messages like the following.
" ACPI CPPC: PCC check channel failed. Status=0 "
Earlier (without above commit) the default transition delay was
taken form the value passed from PCCT. Use the same value provided
by PCCT to set the transition_delay_us.
Fixes: e948bc8fbe (cpufreq: Cap the default transition delay value to 10 ms)
Signed-off-by: George Cherian <george.cherian@cavium.com>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cris architecture is getting removed, including the artpec3
and etraxfs SoCs, so these cpufreq drivers are now unused.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The blackfin architecture is getting removed, so this driver is
now obsolete.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from tegra186 driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from speedstep driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from sparc driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from sh-cpufreq driver.
The driver though prints the min/max frequency values and the same is
done from the ->ready() callback now to keep the behavior unchanged.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from sfi driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from scpi driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from sc520 driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from s3c24xx driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from qoirq driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from pxa driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from ppc_cbe driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from powernow driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from p4-clockmod driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from mediatek driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from longhaul driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from ia64-acpi driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from elanfreq driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from e_powersaver driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from cpufreq-dt driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from brcmstb driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from arm_big_little driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table in the acpi-cpufreq driver.
The driver needs to crosscheck if the max frequency corresponds to the
P-state 0 or not and the same is done from the ->ready() callback now.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq table is already validated by the cpufreq core and none of
the users of cpufreq_generic_init() have any dependency on it to
validate the table as well.
Don't validate the cpufreq table anymore from cpufreq_generic_init().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is a preparatory commit to make policy->suspend_freq independent of
validation of the cpufreq table, as a later commit would update
cpufreq_generic_init() to not validate the cpufreq table any longer.
The driver already assumes the order in which the frequency table is
sorted and we can get the max frequency easily.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A built-in scpi cpufreq driver cannot link against a modular
thermal framework:
drivers/cpufreq/scpi-cpufreq.o: In function `scpi_cpufreq_ready':
scpi-cpufreq.c:(.text+0x4c): undefined reference to `of_cpufreq_cooling_register'
drivers/cpufreq/scpi-cpufreq.o: In function `scpi_cpufreq_exit':
scpi-cpufreq.c:(.text+0x9c): undefined reference to `cpufreq_cooling_unregister'
This adds a Kconfig dependency that makes sure this configuration
is not possible, while allowing all configurations that can work.
Note that disabling CPU_THERMAL means we don't care about the
THERMAL dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from powernv driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A built-in scmi cpufreq driver cannot link against a modular
thermal framework:
drivers/cpufreq/scmi-cpufreq.o: In function `scmi_cpufreq_ready':
scmi-cpufreq.c:(.text+0x40): undefined reference to `of_cpufreq_cooling_register'
drivers/cpufreq/scmi-cpufreq.o: In function `scmi_cpufreq_exit':
scmi-cpufreq.c:(.text+0x88): undefined reference to `cpufreq_cooling_unregister'
This adds a Kconfig dependency that makes sure this configuration
is not possible, while allowing all configurations that can work.
Note that disabling CPU_THERMAL means we don't care about the
THERMAL dependency.
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARM System Control and Management Interface(SCMI)[1] is more flexible and
easily extensible than any of the existing interfaces.
Few existing as well as future ARM platforms provide micro-controllers
to abstract various power and other system management tasks which have
similar interfaces, both in terms of the functions that are provided by
them, and in terms of how requests are communicated to them.
There are quite a few protocols like ARM SCPI, TI SCI, QCOM RPM, Nvidia Tegra
BPMP, and so on already. This specification is to standardize and avoid any
further fragmentation in the design of such interface by various vendors.
The current SCMI driver implementation is very basic and initial support.
It lacks support for notifications, asynchronous/delayed response, perf/power
statistics region and sensor register region.
Mailbox is the only form of transport supported currently in the driver.
SCMI supports interrupt based mailbox communication, where, on completion
of the processing of a message, the caller receives an interrupt as well as
polling for completion.
SCMI is designed to minimize the dependency on the mailbox/transport
hardware. So in terms of SCMI, each channel in the mailbox includes
memory area, doorbell and completion interrupt.
However the doorbell and completion interrupt is highly mailbox dependent
which was bit of controversial as part of SCMI/mailbox discussions.
Arnd and me discussed about the few aspects of SCMI and the mailbox framework:
1. Use of mailbox framework for doorbell type mailbox controller:
- Such hardware may not require any data to be sent to signal the remote
about the presence of a message. The channel will have in-built
information on how to trigger the signal to the remote.
There are few mailbox controller drivers which are purely doorbell based.
e.g.QCOM IPC, STM, Tegra, ACPI PCC,..etc
2. Supporting other mailbox controller:
- SCMI just needs a mechanism to signal the remote firmware. Such
controller may need fixed message to be sent to trigger a doorbell.
In such case we may need to get that data from DT and pass the same
to the controller. It's not covered in the current DT binding, but
can be extended as optional property in future.
However handling notifications may be interesting on such mailbox, but
again there is no way to interpret what the data field(remote message)
means, it could be a bit mask or a number or don't-care.
Arnd mentioned that he doesn't like the way the mailbox binding deals
with doorbell-type hardware, but we do have quite a few precedent drivers
already and changing the binding to add a data field would not make it any
better, but could cause other problems. So he is happy with the status quo
of SCMI implementation.
[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.den0056a/index.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qOck
-----END PGP SIGNATURE-----
Merge tag 'scmi-updates-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers
Pull "ARM SCMI support for v4.17" from Sudeep Holla:
ARM System Control and Management Interface(SCMI)[1] is more flexible and
easily extensible than any of the existing interfaces.
Few existing as well as future ARM platforms provide micro-controllers
to abstract various power and other system management tasks which have
similar interfaces, both in terms of the functions that are provided by
them, and in terms of how requests are communicated to them.
There are quite a few protocols like ARM SCPI, TI SCI, QCOM RPM, Nvidia Tegra
BPMP, and so on already. This specification is to standardize and avoid any
further fragmentation in the design of such interface by various vendors.
The current SCMI driver implementation is very basic and initial support.
It lacks support for notifications, asynchronous/delayed response, perf/power
statistics region and sensor register region.
Mailbox is the only form of transport supported currently in the driver.
SCMI supports interrupt based mailbox communication, where, on completion
of the processing of a message, the caller receives an interrupt as well as
polling for completion.
SCMI is designed to minimize the dependency on the mailbox/transport
hardware. So in terms of SCMI, each channel in the mailbox includes
memory area, doorbell and completion interrupt.
However the doorbell and completion interrupt is highly mailbox dependent
which was bit of controversial as part of SCMI/mailbox discussions.
Arnd and me discussed about the few aspects of SCMI and the mailbox framework:
1. Use of mailbox framework for doorbell type mailbox controller:
- Such hardware may not require any data to be sent to signal the remote
about the presence of a message. The channel will have in-built
information on how to trigger the signal to the remote.
There are few mailbox controller drivers which are purely doorbell based.
e.g.QCOM IPC, STM, Tegra, ACPI PCC,..etc
2. Supporting other mailbox controller:
- SCMI just needs a mechanism to signal the remote firmware. Such
controller may need fixed message to be sent to trigger a doorbell.
In such case we may need to get that data from DT and pass the same
to the controller. It's not covered in the current DT binding, but
can be extended as optional property in future.
However handling notifications may be interesting on such mailbox, but
again there is no way to interpret what the data field(remote message)
means, it could be a bit mask or a number or don't-care.
Arnd mentioned that he doesn't like the way the mailbox binding deals
with doorbell-type hardware, but we do have quite a few precedent drivers
already and changing the binding to add a data field would not make it any
better, but could cause other problems. So he is happy with the status quo
of SCMI implementation.
[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.den0056a/index.html
* tag 'scmi-updates-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
cpufreq: scmi: add support for fast frequency switching
cpufreq: add support for CPU DVFS based on SCMI message protocol
hwmon: add support for sensors exported via ARM SCMI
hwmon: (core) Add hwmon_max to hwmon_sensor_types enumeration
clk: add support for clocks provided by SCMI
firmware: arm_scmi: add device power domain support using genpd
firmware: arm_scmi: add per-protocol channels support using idr objects
firmware: arm_scmi: refactor in preparation to support per-protocol channels
firmware: arm_scmi: add option for polling based performance domain operations
firmware: arm_scmi: add support for polling based SCMI transfers
firmware: arm_scmi: probe and initialise all the supported protocols
firmware: arm_scmi: add initial support for sensor protocol
firmware: arm_scmi: add initial support for power protocol
firmware: arm_scmi: add initial support for clock protocol
firmware: arm_scmi: add initial support for performance protocol
firmware: arm_scmi: add scmi protocol bus to enumerate protocol devices
firmware: arm_scmi: add common infrastructure and support for base protocol
firmware: arm_scmi: add basic driver infrastructure for SCMI
dt-bindings: arm: add support for ARM System Control and Management Interface(SCMI) protocol
dt-bindings: mailbox: add support for mailbox client shared memory
The cpufreq core provides option for drivers to implement fast_switch
callback which is invoked for frequency switching from interrupt context.
This patch adds support for fast_switch callback in SCMI cpufreq driver
by making use of polling based SCMI transfer. It also sets the flag
fast_switch_possible.
Cc: linux-pm@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
On some ARM based systems, a separate Cortex-M based System Control
Processor(SCP) provides the overall power, clock, reset and system
control including CPU DVFS. SCMI Message Protocol is used to
communicate with the SCP.
This patch adds a cpufreq driver for such systems using SCMI interface
to drive CPU DVFS.
Cc: linux-pm@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The script "checkpatch.pl" pointed information out like the following.
WARNING: void function return statements are not generally useful
Thus remove such a statement in the affected functions.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Omit an extra message for a memory allocation failure in these functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Omit extra messages for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Omit an extra message for a memory allocation failure in these functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are two clusters (2 + 4 CPUs) on this platform and a separate
cpufreq policy is available for each of the CPUs. The loop in
tegra186_cpufreq_init() tries to find the structure for the right CPU
and finish initialization. But it is missing a `break` statement at the
end, which forces it to restart the loop even when the CPU already
matched and initialization is done.
Fix that by adding the missing `break` statement.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
By design, cpufreq drivers are responsible for calling
cpufreq_frequency_table_cpuinfo() from their ->init()
callbacks to validate the frequency table.
However, if a cpufreq driver is buggy and fails to do so properly, it
lead to unexpected behavior of the driver or the cpufreq core at a
later point in time. It would be better if the core could
validate the frequency table during driver initialization.
To that end, introduce cpufreq_table_validate_and_sort() and make
the cpufreq core call it right after invoking the ->init() callback
of the driver and destroy the cpufreq policy if the table is invalid.
For the time being the validation of the table happens twice, once
from the driver and then from the core. The individual drivers will
be updated separately to drop table validation if they don't need it
for other reasons.
The frequency table is marked "sorted" or "unsorted" by the new helper
now instead of in cpufreq_table_validate_and_show(), as it should only
be done after validating the table (which the drivers won't do going
forward).
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Subject/changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Ideally the de-allocation of resources should happen in the exact
opposite order in which they were allocated. It helps maintain the code
in long term, even if nothing really breaks with incorrect ordering.
That wasn't followed in cpufreq_online() and it has some
inconsistencies. For example, the symlinks were created from within
the locked region while they are removed only after putting the locks.
Also ->exit() should have been called only after the symlinks are
removed and the lock is dropped, as that was the case when ->init()
was first called.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With multi-platform build images, this shows a message on non mediatek
platforms, which is unnecessary. Convert pr_warn() to pr_debug() here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
commit a307a1e6bc "cpufreq: s3c: use cpufreq_generic_init()"
accidentally broke cpufreq on s3c2410 and s3c2412.
These two platforms don't have a CPU frequency table and used to skip
calling cpufreq_table_validate_and_show() for them. But with the
above commit, we started calling it unconditionally and that will
eventually fail as the frequency table pointer is NULL.
Fix this by calling cpufreq_table_validate_and_show() conditionally
again.
Fixes: a307a1e6bc "cpufreq: s3c: use cpufreq_generic_init()"
Cc: 3.13+ <stable@vger.kernel.org> # v3.13+
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 343a8d17fa (cpufreq: scpi: remove arm_big_little dependency)
changed the cpufreq driver on juno from arm_big_little to scpi.
The scpi set_target function does not call the frequency-invariance
setter function arch_set_freq_scale() like the arm_big_little set_target
function does. As a result the task scheduler load and utilization
signals are not frequency-invariant on this platform anymore.
Fix this by adding a call to arch_set_freq_scale() into
scpi_cpufreq_set_target().
Fixes: 343a8d17fa (cpufreq: scpi: remove arm_big_little dependency)
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull x86 PTI and Spectre related fixes and updates from Ingo Molnar:
"Here's the latest set of Spectre and PTI related fixes and updates:
Spectre:
- Add entry code register clearing to reduce the Spectre attack
surface
- Update the Spectre microcode blacklist
- Inline the KVM Spectre helpers to get close to v4.14 performance
again.
- Fix indirect_branch_prediction_barrier()
- Fix/improve Spectre related kernel messages
- Fix array_index_nospec_mask() asm constraint
- KVM: fix two MSR handling bugs
PTI:
- Fix a paranoid entry PTI CR3 handling bug
- Fix comments
objtool:
- Fix paranoid_entry() frame pointer warning
- Annotate WARN()-related UD2 as reachable
- Various fixes
- Add Add Peter Zijlstra as objtool co-maintainer
Misc:
- Various x86 entry code self-test fixes
- Improve/simplify entry code stack frame generation and handling
after recent heavy-handed PTI and Spectre changes. (There's two
more WIP improvements expected here.)
- Type fix for cache entries
There's also some low risk non-fix changes I've included in this
branch to reduce backporting conflicts:
- rename a confusing x86_cpu field name
- de-obfuscate the naming of single-TLB flushing primitives"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
x86/entry/64: Fix CR3 restore in paranoid_exit()
x86/cpu: Change type of x86_cache_size variable to unsigned int
x86/spectre: Fix an error message
x86/cpu: Rename cpu_data.x86_mask to cpu_data.x86_stepping
selftests/x86/mpx: Fix incorrect bounds with old _sigfault
x86/mm: Rename flush_tlb_single() and flush_tlb_one() to __flush_tlb_one_[user|kernel]()
x86/speculation: Add <asm/msr-index.h> dependency
nospec: Move array_index_nospec() parameter checking into separate macro
x86/speculation: Fix up array_index_nospec_mask() asm constraint
x86/debug: Use UD2 for WARN()
x86/debug, objtool: Annotate WARN()-related UD2 as reachable
objtool: Fix segfault in ignore_unreachable_insn()
selftests/x86: Disable tests requiring 32-bit support on pure 64-bit systems
selftests/x86: Do not rely on "int $0x80" in single_step_syscall.c
selftests/x86: Do not rely on "int $0x80" in test_mremap_vdso.c
selftests/x86: Fix build bug caused by the 5lvl test which has been moved to the VM directory
selftests/x86/pkeys: Remove unused functions
selftests/x86: Clean up and document sscanf() usage
selftests/x86: Fix vDSO selftest segfault for vsyscall=none
x86/entry/64: Remove the unused 'icebp' macro
...
x86_mask is a confusing name which is hard to associate with the
processor's stepping.
Additionally, correct an indent issue in lib/cpu.c.
Signed-off-by: Jia Zhang <qianyue.zj@alibaba-inc.com>
[ Updated it to more recent kernels. ]
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: tony.luck@intel.com
Link: http://lkml.kernel.org/r/1514771530-70829-1-git-send-email-qianyue.zj@alibaba-inc.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Without this, the imx6q-cpufreq driver isn't loaded
automatically when built as a module
Tested on wandboard quad with a fedora 27 kernel rpm
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pointer subtraction is slow and tedious. Therefore, replace all instances
where cpufreq_for_each_{valid_,}entry loops contained such substractions
with an iteration macro providing an index to the frequency_table entry.
Suggested-by: Al Viro <viro@ZenIV.linux.org.uk>
Link: http://lkml.kernel.org/r/20180120020237.GM13338@ZenIV.linux.org.uk
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When maxcpus=1 is in the kernel command line, the BP is responsible
for re-enabling the HWP - because currently only the APs invoke
intel_pstate_hwp_enable() during their online process - which might
put the system into unstable state after resume.
Fix this by enabling the HWP explicitly on BP during resume.
Reported-by: Doug Smythies <dsmythies@telus.net>
Suggested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Yu Chen <yu.c.chen@intel.com>
[ rjw: Subject/changelog, minor modifications ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix to return a negative error code from the clk_get() error handling
case instead of 0, as done elsewhere in this function.
Fixes: 343a8d17fa (cpufreq: scpi: remove arm_big_little dependency)
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 343a8d17fa (cpufreq: scpi: remove arm_big_little dependency)
leads to the following static checker warning:
drivers/cpufreq/scpi-cpufreq.c:203 scpi_cpufreq_ready()
warn: 'cdev' isn't an ERR_PTR
of_cpufreq_cooling_register() returns NULL on error. This patch removes
the incorrect IS_ERR check on the returned pointer.
Fixes: 343a8d17fa (cpufreq: scpi: remove arm_big_little dependency)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since AVR32 arch was removed, at32ap-cpufreq is useless.
Remove this driver.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In ST/CZ CPUID 8000_0007_EDX[11, ProcFeedbackInterface] is 0,
but the mechanism is still available and can be used.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_resume can be called even without preceding cpufreq_suspend.
This can happen in following scenario:
suspend_devices_and_enter
--> dpm_suspend_start
--> dpm_prepare
--> device_prepare : this function errors out
--> dpm_suspend: this is skipped due to dpm_prepare failure
this means cpufreq_suspend is skipped over
--> goto Recover_platform, due to previous error
--> goto Resume_devices
--> dpm_resume_end
--> dpm_resume
--> cpufreq_resume
In case schedutil is used as frequency governor, cpufreq_resume will
eventually call sugov_start, which does following:
memset(sg_cpu, 0, sizeof(*sg_cpu));
....
This effectively erases function pointer for frequency update, causing
crash later on. The function pointer would have been set correctly if
subsequent cpufreq_add_update_util_hook runs successfully, but that
function returns earlier because cpufreq_suspend was not called:
if (WARN_ON(per_cpu(cpufreq_update_util_data, cpu)))
return;
The fix is to check cpufreq_suspended first, if it's false, that means
cpufreq_suspend was not called in the first place, so do not resume
cpufreq.
Signed-off-by: Bo Yan <byan@nvidia.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Dropped printing a message ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpufreq-thermal:
cpu_cooling: Remove static-power related documentation
cpu_cooling: Drop static-power related stuff
cpu_cooling: Keep only one of_cpufreq*cooling_register() helper
cpu_cooling: Remove unused cpufreq_power_cooling_register()
cpu_cooling: Make of_cpufreq_power_cooling_register() parse DT
The dependency on physical_package_id from the topology to get the
cluster identifier is wrong. The concept of cluster used in ARM topology
is unfortunately not well defined in the architecture, we should avoid
using it. Further the frequency domain need not be mapped to so called
"clusters" one to one.
SCPI already provides means to obtain the frequency domain id from the
device tree. In order to support some new topologies(e.g. DSU which
contains 2 frequency domains within the physical cluster), pseudo
clusters are created to make this driver work which is wrong again.
In order to solve those issues and also remove dependency of topological
physical id for frequency domain, this patch removes the arm_big_little
dependency from scpi driver.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some OpenPOWER boxes can have same pstate values for nominal and
pmin pstates. In these boxes the current code will not initialize
'powernv_pstate_info.min' variable and result in erroneous CPU
frequency reporting. This patch fixes this problem.
Fixes: 09ca4c9b59 (cpufreq: powernv: Replacing pstate_id with frequency table index)
Reported-by: Alvin Wang <wangat@tw.ibm.com>
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.8+ <stable@vger.kernel.org> # 4.8+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently intel_pstate can function only in HWP mode on Skylake servers.
When HWP feature is not enabled on the processor then acpi-cpufreq is
driver is used.
Based on the power and performance tests using intel_pstate scaling
algorithm the results are comparable. But intel_pstate brings in
additional features:
- Display of turbo frequency range, which many users like to see
- Place limits in the turbo frequency range when platform allows
Since these tests are done only using non PID algorithm introduced in
kernel version 4.14, this patch is not a backport candidate. So each user
has to carefully weigh the benefits before he backports.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since core_funcs and bxt_funcs have same set of callbacks, replace
bxt_funcs with core_funcs.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add 696MHz operating point for i.MX6UL, only for those
parts with speed grading fuse set to 2b'10 supports
696MHz operating point, so, speed grading check is also
added for i.MX6UL in this patch, the clock tree for each
operating point are as below:
696MHz:
pll1 696000000
pll1_bypass 696000000
pll1_sys 696000000
pll1_sw 696000000
arm 696000000
528MHz:
pll2 528000000
pll2_bypass 528000000
pll2_bus 528000000
ca7_secondary_sel 528000000
step 528000000
pll1_sw 528000000
arm 528000000
396MHz:
pll2_pfd2_396m 396000000
ca7_secondary_sel 396000000
step 396000000
pll1_sw 396000000
arm 396000000
198MHz:
pll2_pfd2_396m 396000000
ca7_secondary_sel 396000000
step 396000000
pll1_sw 396000000
arm 198000000
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It always returns 0 and none of its callers check its return value. Make
it return void.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On POWER8 and POWER9, the PMSR and the PMCR registers define pstates
to be 8-bit wide values. The device-tree exports pstates as 32-bit
wide values of which the lower byte is the actual pstate.
The current implementation in the kernel treats pstates as integer
type, since it used to use the sign of the pstate for performing some
boundary-checks. This is no longer required after the patch
"powernv-cpufreq: Fix pstate_to_idx() to handle non-continguous
pstates".
So, in this patch, we modify the powernv-cpufreq driver to uniformly
treat pstates as opaque 8-bit values obtained from the device-tree or
the PMCR. This simplifies the extract_pstate() helper function since
we no longer no longer require to worry about the sign-extentions.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The code in powernv-cpufreq, makes the following two assumptions which
are not guaranteed by the device-tree bindings:
1) Pstate ids are continguous: This is used in pstate_to_idx() to
obtain the reverse map from a pstate to it's corresponding
entry into the cpufreq frequency table.
2) Every Pstate should always lie between the max and the min
pstates that are explicitly reported in the device tree: This
is used to determine whether a pstate reported by the PMSR is
out of bounds.
Both these assumptions are unwarranted and can change on future
platforms.
In this patch, we maintain the reverse map from a pstate to it's index
in the cpufreq frequency table and use this in pstate_to_idx(). This
does away with the assumptions (1) mentioned above, and will work with
non continguous pstate ids. If no entry exists for a particular
pstate, then such a pstate is treated as being out of bounds. This
gets rid of assumption (2).
On all the existing platforms, where the pstates are 8-bit long
values, the new implementation of pstate_to_idx() takes constant time.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On POWERNV platform, the fields for pstates in the Power Management
Status Register (PMSR) and the Power Management Control Register
(PMCR) are 8-bits wide. On POWER8 the pstates are negatively numbered
while on POWER9 they are positively numbered.
The device-tree exports pstates as 32-bit entries. The device-tree
implementation sign-extends the 8-bit pstate values to obtain the
corresponding 32-bit entry.
Eg: On POWER8, a pstate value 0x82 [-126] is represented in the
device-tree as 0xfffffff82 while on POWER9, the same value 0x82 [130]
is represented in the device-tree as 0x00000082.
The powernv-cpufreq driver implementation represents pstates using the
integer type. In multiple places in the driver, the code interprets
the pstates extracted from the PMSR as a signed byte and assigns it to
a integer variable to get the sign-extention.
On POWER9 platforms which have greater than 128 pstates, this results
in the driver performing incorrect sign-extention, and thereby
treating a legitimate pstate (say 130) as an invalid pstates (since it
is interpreted as -126).
This patch fixes the issue by implementing a helper function to
extract Pstates from PMSR register, and correctly sign-extend it to be
consistent with the values provided by the device-tree.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use clk_bulk_get() to simplify the driver's clocks handling.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit aa7519af45 (cpufreq: Use transition_delay_us for legacy
governors as well) the sampling_rate field of struct dbs_data may be
less than the tick period which causes dbs_update() to produce
incorrect results, so make the code ensure that the value of that
field will always be sufficiently large.
Fixes: aa7519af45 (cpufreq: Use transition_delay_us for legacy governors as well)
Reported-by: Andy Tang <andy.tang@nxp.com>
Reported-by: Doug Smythies <dsmythies@telus.net>
Tested-by: Andy Tang <andy.tang@nxp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The commit moving the speed grading check to the cpufreq driver introduced
some additional checks, so the OPP disable is only attempted on SoCs where
those OPPs are present. The compatible checks are missing the QuadPlus
compatible, so invalid OPPs are not correctly disabled there.
Move both checks to a single condition, so we don't need to sprinkle even
more calls to of_machine_is_compatible().
Fixes: 2b3d58a3ad (cpufreq: imx6q: Move speed grading check to cpufreq driver)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some platforms, like those in the DRA7 and AM57 families, require the
scaling of multiple regulators in order to properly support higher OPPs.
Let the ti-cpufreq driver determine when this is required and pass the
appropriate regulator names to the OPP core so that they can be properly
managed.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ti-cpufreq will be responsible for calling dev_pm_opp_set_regulators on
platforms that require AVS and ABB regulator support so we must be
able to defer probe if regulators are not yet available, so change
ti-cpufreq to be a module_platform_driver to allow for probe defer.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds DVFS support for the Armada 37xx SoCs
There are up to four CPU frequency loads for Armada 37xx controlled by
the hardware.
This driver associates the CPU load level to a frequency, then the
hardware will switch while selecting a load level.
The hardware also can associate a voltage for each level (AVS support)
but it is not yet supported
Tested-by: Andre Heider <a.heider@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since the introduction of this driver, the functions to remove the opp
were added. So stop claiming we can't remove opp and use one of them in
case of failure.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In case of error the clock reference was freed but not in normal path
once it was nor more used. This patch fixes it.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Group all the related big LITTLE configuration together and sort the
other entries in alphabetic order.
Also fixing tab vs space issue while mofifying these entries.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
mediatek projects will use mediate-cpufreq.c as cpufreq driver,
instead of using cpufreq_dt.c
Add mediatek related projects into cpufreq-dt blacklist
Signed-off-by: Andrew-sh Cheng <andrew-sh.cheng@mediatek.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Support mt2712 in mediatek-cpufreq.c
Signed-off-by: Andrew-sh Cheng <andrew-sh.cheng@mediatek.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The commit e948bc8fbe ("cpufreq: Cap the default transition delay
value to 10 ms") caused a regression on EPIA-M min-ITX computer where
shutdown or reboot hangs occasionally with a print message like:
longhaul: Warning: Timeout while waiting for idle PCI bus
cpufreq: __target_index: Failed to change cpu frequency: -16
This probably happens because the cpufreq governor tries to change the
frequency of the CPU faster than allowed by the hardware.
Before the above commit, the default transition delay was set to 200 ms
for a transition_latency of 200000 ns. Lets revert back to that
transition delay value to fix it. Note that several other transition
delay values were tested like 20 ms and 30 ms and none of them have
resolved system hang issue completely.
Fixes: e948bc8fbe (cpufreq: Cap the default transition delay value to 10 ms)
Reported-by: Meelis Roos <mroos@linux.ee>
Suggested-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
of_cpufreq_cooling_register() isn't used by anyone and so can be
removed, but then we would be left with two routines:
cpufreq_cooling_register() and of_cpufreq_power_cooling_register() that
would look odd.
Remove current implementation of of_cpufreq_cooling_register() and
rename of_cpufreq_power_cooling_register() as
of_cpufreq_cooling_register(). This simplifies lots of stuff.
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
All the callers of of_cpufreq_power_cooling_register() have almost
identical code and it makes more sense to move that code into the helper
as its all about reading DT properties.
This got rid of lot of redundant code.
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is possible to remove a cpufreq governor module after
cpufreq_parse_governor() has returned success in
store_scaling_governor() and before cpufreq_set_policy()
acquires a reference to it, because the governor list is
not protected during that period and nothing prevents the
governor from being unregistered then.
Prevent that from happening by acquiring an extra reference
to the governor module temporarily in cpufreq_parse_governor(),
under cpufreq_governor_mutex, and dropping it in
store_scaling_governor(), when cpufreq_set_policy() returns.
Note that the second cpufreq_parse_governor() call site is fine,
because it only cares about the policy member of new_policy.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Drop a pointless return statement from cpufreq_unregister_governor().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pass policy pointer to cpufreq_parse_governor() instead of passing
pointers to two members of it so as to make the code slightly more
straightforward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Drop an unnecessary local variable from cpufreq_parse_governor()
and rearrange the code in there to make it easier to follow.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/cpufreq/mediatek-cpufreq.o
see include/linux/module.h for more information
This adds the license as "GPL v2", which matches the header of the file.
MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The MIPS loongson cpufreq drivers don't build unless configured for the
correct machine type, due to dependency on machine specific architecture
headers and symbols in machine specific platform code.
More specifically loongson1-cpufreq.c uses RST_CPU_EN and RST_CPU,
neither of which is defined in asm/mach-loongson32/regs-clk.h unless
CONFIG_LOONGSON1_LS1B=y, and loongson2_cpufreq.c references
loongson2_clockmod_table[], which is only defined in
arch/mips/loongson64/lemote-2f/clock.c, i.e. when
CONFIG_LEMOTE_MACH2F=y.
Add these dependencies to Kconfig to avoid randconfig / allyesconfig
build failures (e.g. when based on BMIPS which also has a cpufreq
driver).
Signed-off-by: James Hogan <jhogan@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Relocate the OPP (Operating Performance Points) framework to its
own directory under drivers/ and add support for power domain
performance states to it (Viresh Kumar).
- Modify the PM core, the PCI bus type and the ACPI PM domain to
support power management driver flags allowing device drivers to
specify their capabilities and preferences regarding the handling
of devices with enabled runtime PM during system suspend/resume
and clean up that code somewhat (Rafael Wysocki, Ulf Hansson).
- Add frequency-invariant accounting support to the task scheduler
on ARM and ARM64 (Dietmar Eggemann).
- Fix PM QoS device resume latency framework to prevent "no
restriction" requests from overriding requests with specific
requirements and drop the confusing PM_QOS_FLAG_REMOTE_WAKEUP
device PM QoS flag (Rafael Wysocki).
- Drop legacy class suspend/resume operations from the PM core
and drop legacy bus type suspend and resume callbacks from
ARM/locomo (Rafael Wysocki).
- Add min/max frequency support to devfreq and clean it up
somewhat (Chanwoo Choi).
- Rework wakeup support in the generic power domains (genpd)
framework and update some of its users accordingly (Geert
Uytterhoeven).
- Convert timers in the PM core to use timer_setup() (Kees Cook).
- Add support for exposing the SLP_S0 (Low Power S0 Idle)
residency counter based on the LPIT ACPI table on Intel
platforms (Srinivas Pandruvada).
- Add per-CPU PM QoS resume latency support to the ladder cpuidle
governor (Ramesh Thomas).
- Fix a deadlock between the wakeup notify handler and the
notifier removal in the ACPI core (Ville Syrjälä).
- Fix a cpufreq schedutil governor issue causing it to use
stale cached frequency values sometimes (Viresh Kumar).
- Fix an issue in the system suspend core support code causing
wakeup events detection to fail in some cases (Rajat Jain).
- Fix the generic power domains (genpd) framework to prevent
the PM core from using the direct-complete optimization with
it as that is guaranteed to fail (Ulf Hansson).
- Fix a minor issue in the cpuidle core and clean it up a bit
(Gaurav Jindal, Nicholas Piggin).
- Fix and clean up the intel_idle and ARM cpuidle drivers (Jason
Baron, Len Brown, Leo Yan).
- Fix a couple of minor issues in the OPP framework and clean it
up (Arvind Yadav, Fabio Estevam, Sudeep Holla, Tobias Jordan).
- Fix and clean up some cpufreq drivers and fix a minor issue in
the cpufreq statistics code (Arvind Yadav, Bhumika Goyal, Fabio
Estevam, Gautham Shenoy, Gustavo Silva, Marek Szyprowski, Masahiro
Yamada, Robert Jarzmik, Zumeng Chen).
- Fix minor issues in the system suspend and hibernation core, in
power management documentation and in the AVS (Adaptive Voltage
Scaling) framework (Helge Deller, Himanshu Jha, Joe Perches,
Rafael Wysocki).
- Fix some issues in the cpupower utility and document that Shuah
Khan is going to maintain it going forward (Prarit Bhargava,
Shuah Khan).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJaCg2eAAoJEILEb/54YlRxGhAP/26D5TvfQ65wtf2W0Gas/tsP
+24SzCLQO2GWalhbOXZbXhnBn/eCovKB6T8VB0V7Bff0VcUOK9szmBu9hOBJfXGN
ec2oYKtWPwqzkgPfbqjZhQTp5EXg/dmWYOhAMA7HLMv7oVZqoRZ/MNOJPooXAmQj
NEVWj3Eap0anic0ZgGMN4FaIMF6CHP2rAheqWQVXihhXpjIOWrJCjEoPZfbH1bFC
+zd9Batd3rq+eZ5dYxg+znpYcZi69kmPw+KASYsaWTJzNjYbR+VLOxqzx7Icdgbz
4glwWNe7lZGCAj+BIKGaHN5CR/fAXqkPvJ8csn6qISyUJ1Gph6otRfvuUaK58F4T
1Rmcj+mGXgJBcjaQGmVQIITKD6drBW/l50MJlze5JUM4A7VM2Di/cctgoWmOJsnO
2f6D6PYGuW0Fe8uUVGki/ddApXvoTGbEx+ncQ5+At+mLMKJwYfND9h2stOkCcrTy
k4Pr+XpVU9hXwYVX3a1Au41bFQiXYwguxD1TH1LaY3liAWXvo0qNc/Ib6mW8e7pL
wqPoe2/yxgVw5rsQPcKxVxAFFgjAAIdU3Xw44ETTPN315CLOoiuZgWkeTrnYCdix
DaBWu1VN9tU5U6FWBlWXDb06i5qvSo3aYzLnSBC6fm7qX2SuDxGiQTcyOQ7H1NiQ
d1wzhgObW98N7rZRaByu
=QTnx
-----END PGP SIGNATURE-----
Merge tag 'pm-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"There are no real big ticket items here this time.
The most noticeable change is probably the relocation of the OPP
(Operating Performance Points) framework to its own directory under
drivers/ as it has grown big enough for that. Also Viresh is now going
to maintain it and send pull requests for it to me, so you will see
this change in the git history going forward (but still not right
now).
Another noticeable set of changes is the modifications of the PM core,
the PCI subsystem and the ACPI PM domain to allow of more integration
between system-wide suspend/resume and runtime PM. For now it's just a
way to avoid resuming devices from runtime suspend unnecessarily
during system suspend (if the driver sets a flag to indicate its
readiness for that) and in the works is an analogous mechanism to
allow devices to stay suspended after system resume.
In addition to that, we have some changes related to supporting
frequency-invariant CPU utilization metrics in the scheduler and in
the schedutil cpufreq governor on ARM and changes to add support for
device performance states to the generic power domains (genpd)
framework.
The rest is mostly fixes and cleanups of various sorts.
Specifics:
- Relocate the OPP (Operating Performance Points) framework to its
own directory under drivers/ and add support for power domain
performance states to it (Viresh Kumar).
- Modify the PM core, the PCI bus type and the ACPI PM domain to
support power management driver flags allowing device drivers to
specify their capabilities and preferences regarding the handling
of devices with enabled runtime PM during system suspend/resume and
clean up that code somewhat (Rafael Wysocki, Ulf Hansson).
- Add frequency-invariant accounting support to the task scheduler on
ARM and ARM64 (Dietmar Eggemann).
- Fix PM QoS device resume latency framework to prevent "no
restriction" requests from overriding requests with specific
requirements and drop the confusing PM_QOS_FLAG_REMOTE_WAKEUP
device PM QoS flag (Rafael Wysocki).
- Drop legacy class suspend/resume operations from the PM core and
drop legacy bus type suspend and resume callbacks from ARM/locomo
(Rafael Wysocki).
- Add min/max frequency support to devfreq and clean it up somewhat
(Chanwoo Choi).
- Rework wakeup support in the generic power domains (genpd)
framework and update some of its users accordingly (Geert
Uytterhoeven).
- Convert timers in the PM core to use timer_setup() (Kees Cook).
- Add support for exposing the SLP_S0 (Low Power S0 Idle) residency
counter based on the LPIT ACPI table on Intel platforms (Srinivas
Pandruvada).
- Add per-CPU PM QoS resume latency support to the ladder cpuidle
governor (Ramesh Thomas).
- Fix a deadlock between the wakeup notify handler and the notifier
removal in the ACPI core (Ville Syrjälä).
- Fix a cpufreq schedutil governor issue causing it to use stale
cached frequency values sometimes (Viresh Kumar).
- Fix an issue in the system suspend core support code causing wakeup
events detection to fail in some cases (Rajat Jain).
- Fix the generic power domains (genpd) framework to prevent the PM
core from using the direct-complete optimization with it as that is
guaranteed to fail (Ulf Hansson).
- Fix a minor issue in the cpuidle core and clean it up a bit (Gaurav
Jindal, Nicholas Piggin).
- Fix and clean up the intel_idle and ARM cpuidle drivers (Jason
Baron, Len Brown, Leo Yan).
- Fix a couple of minor issues in the OPP framework and clean it up
(Arvind Yadav, Fabio Estevam, Sudeep Holla, Tobias Jordan).
- Fix and clean up some cpufreq drivers and fix a minor issue in the
cpufreq statistics code (Arvind Yadav, Bhumika Goyal, Fabio
Estevam, Gautham Shenoy, Gustavo Silva, Marek Szyprowski, Masahiro
Yamada, Robert Jarzmik, Zumeng Chen).
- Fix minor issues in the system suspend and hibernation core, in
power management documentation and in the AVS (Adaptive Voltage
Scaling) framework (Helge Deller, Himanshu Jha, Joe Perches, Rafael
Wysocki).
- Fix some issues in the cpupower utility and document that Shuah
Khan is going to maintain it going forward (Prarit Bhargava, Shuah
Khan)"
* tag 'pm-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (88 commits)
tools/power/cpupower: add libcpupower.so.0.0.1 to .gitignore
tools/power/cpupower: Add 64 bit library detection
intel_idle: Graceful probe failure when MWAIT is disabled
cpufreq: schedutil: Reset cached_raw_freq when not in sync with next_freq
freezer: Fix typo in freezable_schedule_timeout() comment
PM / s2idle: Clear the events_check_enabled flag
cpufreq: stats: Handle the case when trans_table goes beyond PAGE_SIZE
cpufreq: arm_big_little: make cpufreq_arm_bL_ops structures const
cpufreq: arm_big_little: make function arguments and structure pointer const
cpuidle: Avoid assignment in if () argument
cpuidle: Clean up cpuidle_enable_device() error handling a bit
ACPI / PM: Fix acpi_pm_notifier_lock vs flush_workqueue() deadlock
PM / Domains: Fix genpd to deal with drivers returning 1 from ->prepare()
cpuidle: ladder: Add per CPU PM QoS resume latency support
PM / QoS: Fix device resume latency framework
PM / domains: Rework governor code to be more consistent
PM / Domains: Remove gpd_dev_ops.active_wakeup() callback
soc: rockchip: power-domain: Use GENPD_FLAG_ACTIVE_WAKEUP
soc: mediatek: Use GENPD_FLAG_ACTIVE_WAKEUP
ARM: shmobile: pm-rmobile: Use GENPD_FLAG_ACTIVE_WAKEUP
...
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
* pm-cpufreq: (22 commits)
cpufreq: stats: Handle the case when trans_table goes beyond PAGE_SIZE
cpufreq: arm_big_little: make cpufreq_arm_bL_ops structures const
cpufreq: arm_big_little: make function arguments and structure pointer const
cpufreq: pxa: convert to clock API
cpufreq: speedstep-lib: mark expected switch fall-through
cpufreq: ti-cpufreq: add missing of_node_put()
cpufreq: dt: Remove support for Exynos4212 SoCs
cpufreq: imx6q: Move speed grading check to cpufreq driver
cpufreq: ti-cpufreq: kfree opp_data when failure
cpufreq: SPEAr: pr_err() strings should end with newlines
cpufreq: powernow-k8: pr_err() strings should end with newlines
cpufreq: dt-platdev: drop socionext,uniphier-ld6b from whitelist
arm64: wire cpu-invariant accounting support up to the task scheduler
arm64: wire frequency-invariant accounting support up to the task scheduler
arm: wire cpu-invariant accounting support up to the task scheduler
arm: wire frequency-invariant accounting support up to the task scheduler
drivers base/arch_topology: allow inlining cpu-invariant accounting support
drivers base/arch_topology: provide frequency-invariant accounting support
cpufreq: dt: invoke frequency-invariance setter function
cpufreq: arm_big_little: invoke frequency-invariance setter function
...
On platforms with large number of Pstates, the transition table, which
is a NxN matrix, can overflow beyond the PAGE_SIZE boundary.
This can be seen on POWER9 which has 100+ Pstates.
As a result, each time the trans_table is read for any of the CPUs, we
will get the following error.
---------------------------------------------------
fill_read_buffer: show+0x0/0xa0 returned bad count
---------------------------------------------------
This patch ensures that in case of an overflow, we print a warning
once in the dmesg and return FILE TOO LARGE error for this and all
subsequent accesses of trans_table.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make these const as they are only getting passed to the functions
bL_cpufreq_{register/unregister} having the arguments as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make the arguments of functions bL_cpufreq_{register/unregister} as
const as the ops pointer does not modify the fields of the
cpufreq_arm_bL_ops structure it points to. The pointer arm_bL_ops is
also getting initialized with ops but the pointer does not modify the
fields. So, make the function argument and the structure pointer const.
Add const to function prototypes too.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the clock settings have been introduced into the clock pxa drivers,
which are now available to change the CPU clock by themselves, remove
the clock handling from this driver, and rely on pxa clock drivers.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
call of_node_put to release the refcount of np.
Signed-off-by: Zumeng Chen <zumeng.chen@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Support for Exynos4212 SoCs has been removed by commit bca9085e0a
"ARM: dts: exynos: remove Exynos4212 support (dead code)", so there
is no need to keep remaining dead code related to this SoC version.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On some i.MX6 SoCs (like i.MX6SL, i.MX6SX and i.MX6UL) that do not have
speed grading check, opp table will not be created in platform code,
so cpufreq driver prints the following error message:
cpu cpu0: dev_pm_opp_get_opp_count: OPP table not found (-19)
However, this is not really an error in this case because the
imx6q-cpufreq driver first calls dev_pm_opp_get_opp_count()
and if it fails, it means that platform code does not provide
OPP and then dev_pm_opp_of_add_table() will be called.
In order to avoid such confusing error message, move the speed grading
check from platform code to the imx6q-cpufreq driver.
This way the imx6q-cpufreq no longer has to check whether OPP table
is supplied by platform code.
Tested on a i.MX6Q and i.MX6UL based boards.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This refactors the only user of init_timer_pinned_deferrable() to use the
new timer_setup() and from_timer(). Adds a pointer back to the policy,
and drops the definition of init_timer_pinned_deferrable().
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Petr Mladek <pmladek@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: linux1394-devel@lists.sourceforge.net
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: linux-s390@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Ursula Braun <ubraun@linux.vnet.ibm.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Harish Patil <harish.patil@cavium.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Manish Chopra <manish.chopra@cavium.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-pm@vger.kernel.org
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Mark Gross <mark.gross@intel.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Michael Reed <mdr@sgi.com>
Cc: netdev@vger.kernel.org
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lkml.kernel.org/r/1507159627-127660-3-git-send-email-keescook@chromium.org
pr_err() messages should terminated with a new-line to avoid
other messages being concatenated onto the end.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pr_err() messages should terminated with a new-line to avoid
other messages being concatenated onto the end.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As you see arch/arm/boot/dts/uniphier-ld6b.dtsi, it includes
uniphier-pxs2.dtsi, which uses "operating-points-v2" property
and whose cpufreq device is automatically created.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Call the frequency-invariance setter function arch_set_freq_scale()
if the new frequency has been successfully set which is indicated by
dev_pm_opp_set_rate() returning 0.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Call the frequency-invariance setter function arch_set_freq_scale()
if the new frequency has been successfully set which is indicated by
bL_cpufreq_set_rate() returning 0.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Frequency-invariant accounting support based on the ratio of current
frequency and maximum supported frequency is an optional feature an arch
can implement.
Since there are cpufreq drivers (e.g. cpufreq-dt) which can be build for
different arch's a default implementation of the frequency-invariance
setter function arch_set_freq_scale() is needed.
This default implementation is an empty weak function which will be
overwritten by a strong function in case the arch provides one.
The setter function passes the cpumask of related (to the frequency
change) cpus (online and offline cpus), the (new) current frequency and
the maximum supported frequency.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rather than letting the ti-cpufreq driver match against 'ti,am4372'
machine compatible during probe let's match against 'ti,am43' so that we
can support both 'ti,am4372' and 'ti,am438x' platforms which both match
to this compatible.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit edeec420de (cpufreq: dt-platdev: Automatically create cpufreq
device with OPP v2) missed adding few platforms to the blacklist which
create the cpufreq-dt device from their own drivers, after some
dependencies are sorted out.
And for those platforms, both the platform specific driver and the
cpufreq-dt-platdev driver try to create the cpufreq-dt device now.
Fix that by including those platforms in the blacklist. This doesn't include
the TI platforms, for which there is a separate patch.
Fixes: edeec420de (cpufreq: dt-cpufreq: platdev Automatically create device with OPP v2)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
- Update the ACPICA code in the kernel to upstream revision 20170728
including:
* Alias operator handling update (Bob Moore).
* Deferred resolution of reference package elements (Bob Moore).
* Support for the _DMA method in walk resources (Bob Moore).
* Tables handling update and support for deferred table
verification (Lv Zheng).
* Update of SMMU models for IORT (Robin Murphy).
* Compiler and disassembler updates (Alex James, Erik Schmauss,
Ganapatrao Kulkarni, James Morse).
* Tools updates (Erik Schmauss, Lv Zheng).
* Assorted minor fixes and cleanups (Bob Moore, Kees Cook,
Lv Zheng, Shao Ming).
- Rework the initialization of non-wakeup GPEs with method handlers
in order to address a boot crash on some systems with Thunderbolt
devices connected at boot time where we miss an early hotplug
event due to a delay in GPE enabling (Rafael Wysocki).
- Rework the handling of PCI bridges when setting up ACPI-based
device wakeup in order to avoid disabling wakeup for bridges
prematurely (Rafael Wysocki).
- Consolidate Apple DMI checks throughout the tree, add support for
Apple device properties to the device properties framework and
use these properties for the handling of I2C and SPI devices on
Apple systems (Lukas Wunner).
- Add support for _DMA to the ACPI-based device properties lookup
code and make it possible to use the information from there to
configure DMA regions on ARM64 systems (Lorenzo Pieralisi).
- Fix several issues in the APEI code, add support for exporting
the BERT error region over sysfs and update APEI MAINTAINERS
entry with reviewers information (Borislav Petkov, Dongjiu Geng,
Loc Ho, Punit Agrawal, Tony Luck, Yazen Ghannam).
- Fix a potential initialization ordering issue in the ACPI EC
driver and clean it up somewhat (Lv Zheng).
- Update the ACPI SPCR driver to extend the existing XGENE 8250
workaround in it to a new platform (m400) and to work around
an Xgene UART clock issue (Graeme Gregory).
- Add a new utility function to the ACPI core to support using
ACPI OEM ID / OEM Table ID / Revision for system identification
in blacklisting or similar and switch over the existing code
already using this information to this new interface (Toshi Kani).
- Fix an xpower PMIC issue related to GPADC reads that always return
0 without extra pin manipulations (Hans de Goede).
- Add statements to print debug messages in a couple of places in
the ACPI core for easier diagnostics (Rafael Wysocki).
- Clean up the ACPI processor driver slightly (Colin Ian King,
Hanjun Guo).
- Clean up the ACPI x86 boot code somewhat (Andy Shevchenko).
- Add a quirk for Dell OptiPlex 9020M to the ACPI backlight
driver (Alex Hung).
- Assorted fixes, cleanups and updates related to ACPI (Amitoj Kaur
Chawla, Bhumika Goyal, Frank Rowand, Jean Delvare, Punit Agrawal,
Ronald Tschalär, Sumeet Pawnikar).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6Ke9
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These include a usual ACPICA code update (this time to upstream
revision 20170728), a fix for a boot crash on some systems with
Thunderbolt devices connected at boot time, a rework of the handling
of PCI bridges when setting up device wakeup, new support for Apple
device properties, support for DMA configurations reported via ACPI on
ARM64, APEI-related updates, ACPI EC driver updates and assorted minor
modifications in several places.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20170728
including:
* Alias operator handling update (Bob Moore).
* Deferred resolution of reference package elements (Bob Moore).
* Support for the _DMA method in walk resources (Bob Moore).
* Tables handling update and support for deferred table
verification (Lv Zheng).
* Update of SMMU models for IORT (Robin Murphy).
* Compiler and disassembler updates (Alex James, Erik Schmauss,
Ganapatrao Kulkarni, James Morse).
* Tools updates (Erik Schmauss, Lv Zheng).
* Assorted minor fixes and cleanups (Bob Moore, Kees Cook, Lv
Zheng, Shao Ming).
- Rework the initialization of non-wakeup GPEs with method handlers
in order to address a boot crash on some systems with Thunderbolt
devices connected at boot time where we miss an early hotplug event
due to a delay in GPE enabling (Rafael Wysocki).
- Rework the handling of PCI bridges when setting up ACPI-based
device wakeup in order to avoid disabling wakeup for bridges
prematurely (Rafael Wysocki).
- Consolidate Apple DMI checks throughout the tree, add support for
Apple device properties to the device properties framework and use
these properties for the handling of I2C and SPI devices on Apple
systems (Lukas Wunner).
- Add support for _DMA to the ACPI-based device properties lookup
code and make it possible to use the information from there to
configure DMA regions on ARM64 systems (Lorenzo Pieralisi).
- Fix several issues in the APEI code, add support for exporting the
BERT error region over sysfs and update APEI MAINTAINERS entry with
reviewers information (Borislav Petkov, Dongjiu Geng, Loc Ho, Punit
Agrawal, Tony Luck, Yazen Ghannam).
- Fix a potential initialization ordering issue in the ACPI EC driver
and clean it up somewhat (Lv Zheng).
- Update the ACPI SPCR driver to extend the existing XGENE 8250
workaround in it to a new platform (m400) and to work around an
Xgene UART clock issue (Graeme Gregory).
- Add a new utility function to the ACPI core to support using ACPI
OEM ID / OEM Table ID / Revision for system identification in
blacklisting or similar and switch over the existing code already
using this information to this new interface (Toshi Kani).
- Fix an xpower PMIC issue related to GPADC reads that always return
0 without extra pin manipulations (Hans de Goede).
- Add statements to print debug messages in a couple of places in the
ACPI core for easier diagnostics (Rafael Wysocki).
- Clean up the ACPI processor driver slightly (Colin Ian King, Hanjun
Guo).
- Clean up the ACPI x86 boot code somewhat (Andy Shevchenko).
- Add a quirk for Dell OptiPlex 9020M to the ACPI backlight driver
(Alex Hung).
- Assorted fixes, cleanups and updates related to ACPI (Amitoj Kaur
Chawla, Bhumika Goyal, Frank Rowand, Jean Delvare, Punit Agrawal,
Ronald Tschalär, Sumeet Pawnikar)"
* tag 'acpi-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (75 commits)
ACPI / APEI: Suppress message if HEST not present
intel_pstate: convert to use acpi_match_platform_list()
ACPI / blacklist: add acpi_match_platform_list()
ACPI, APEI, EINJ: Subtract any matching Register Region from Trigger resources
ACPI: make device_attribute const
ACPI / sysfs: Extend ACPI sysfs to provide access to boot error region
ACPI: APEI: fix the wrong iteration of generic error status block
ACPI / processor: make function acpi_processor_check_duplicates() static
ACPI / EC: Clean up EC GPE mask flag
ACPI: EC: Fix possible issues related to EC initialization order
ACPI / PM: Add debug statements to acpi_pm_notify_handler()
ACPI: Add debug statements to acpi_global_event_handler()
ACPI / scan: Enable GPEs before scanning the namespace
ACPICA: Make it possible to enable runtime GPEs earlier
ACPICA: Dispatch active GPEs at init time
ACPI: SPCR: work around clock issue on xgene UART
ACPI: SPCR: extend XGENE 8250 workaround to m400
ACPI / LPSS: Don't abort ACPI scan on missing mem resource
mailbox: pcc: Drop uninformative output during boot
ACPI/IORT: Add IORT named component memory address limits
...
* intel_pstate:
cpufreq: intel_pstate: Shorten a couple of long names
cpufreq: intel_pstate: Simplify intel_pstate_adjust_pstate()
cpufreq: intel_pstate: Improve IO performance with per-core P-states
cpufreq: intel_pstate: Drop INTEL_PSTATE_HWP_SAMPLING_INTERVAL
cpufreq: intel_pstate: Drop ->update_util from pstate_funcs
cpufreq: intel_pstate: Do not use PID-based P-state selection
* pm-cpufreq-sched:
cpufreq: schedutil: Always process remote callback with slow switching
cpufreq: schedutil: Don't restrict kthread to related_cpus unnecessarily
cpufreq: Return 0 from ->fast_switch() on errors
cpufreq: Simplify cpufreq_can_do_remote_dvfs()
cpufreq: Process remote callbacks from any CPU if the platform permits
sched: cpufreq: Allow remote cpufreq callbacks
cpufreq: schedutil: Use unsigned int for iowait boost
cpufreq: schedutil: Make iowait boost more energy efficient
* pm-cpufreq: (33 commits)
cpufreq: imx6q: Fix imx6sx low frequency support
cpufreq: speedstep-lib: make several arrays static, makes code smaller
cpufreq: ti: Fix 'of_node_put' being called twice in error handling path
cpufreq: dt-platdev: Drop few entries from whitelist
cpufreq: dt-platdev: Automatically create cpufreq device with OPP v2
ARM: ux500: don't select CPUFREQ_DT
cpufreq: Convert to using %pOF instead of full_name
cpufreq: Cap the default transition delay value to 10 ms
cpufreq: dbx500: Delete obsolete driver
mfd: db8500-prcmu: Get rid of cpufreq dependency
cpufreq: enable the DT cpufreq driver on the Ux500
cpufreq: Loongson2: constify platform_device_id
cpufreq: dt: Add r8a7796 support to to use generic cpufreq driver
cpufreq: remove setting of policy->cpu in policy->cpus during init
cpufreq: mediatek: add support of cpufreq to MT7622 SoC
cpufreq: mediatek: add cleanups with the more generic naming
cpufreq: rcar: Add support for R8A7795 SoC
cpufreq: dt: Add rk3328 compatible to use generic cpufreq driver
cpufreq: s5pv210: add missing of_node_put()
cpufreq: Allow dynamic switching with CPUFREQ_ETERNAL latency
...
Convert to use acpi_match_platform_list() for the platform check.
There is no change in functionality.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch contains the minimal changes required to support imx6sx OPP
of 198 Mhz. Without this patch cpufreq still reports success but the
frequency is not changed, the "arm" clock will still be at 396000000 in
clk_summary.
In order to do this PLL1 needs to be still kept enabled while changing
the ARM clock. This is a hardware requirement: when ARM_PODF is changed
in CCM we need to check the busy bit of CCM_CDHIPR bit 16 arm_podf_busy,
and this bit is sync with PLL1 clock, so if PLL1 NOT enabled, this
bit will never get clear.
Keep pll1_sys explicitly enabled until after the rate is change to deal
with this. Otherwise from the clk framework perspective pll1_sys is
unused and gets turned off.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Don't populate arrays on the stack, instead make them static.
Makes the object code smaller by over 860 bytes:
Before:
text data bss dec hex filename
10716 5196 0 15912 3e28 drivers/cpufreq/speedstep-lib.o
After:
text data bss dec hex filename
9690 5356 0 15046 3ac6 drivers/cpufreq/speedstep-lib.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If 'dev_pm_opp_set_supported_hw()' fails, 'opp_data->opp_node' refcount
will be decremented 2 times.
One, just a few lines above, and another one in the error handling path.
Fix it by simply moving the 'of_node_put' call of the normal path.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Drop few ARM (32 and 64 bit) platforms from the whitelist which always
use "operating-points-v2" property from their DT. They should continue
to work after this patch.
Tested on Hikey platform (only the "hisilicon,hi6220" entry).
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The initial idea of creating the cpufreq-dt-platdev.c file was to keep a
list of platforms that use the "operating-points" (V1) bindings and
create cpufreq device for them only, as we weren't sure which platforms
would want the device to get created automatically as some had their own
cpufreq drivers as well, or wanted to initialize cpufreq after doing
some stuff from platform code.
But that wasn't the case with platforms using "operating-points-v2"
property. We wanted the device to get created automatically without the
need of adding them to the whitelist. Though, we will still have some
exceptions where we don't want to create the device automatically.
Rename the earlier platform list as *whitelist* and create a new
*blacklist* as well.
The cpufreq-dt device will get created if:
- The platform is there in the whitelist OR
- The platform has "operating-points-v2" property in CPU0's DT node and
isn't part of the blacklist .
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If transition_delay_us isn't defined by the cpufreq driver, the default
value of transition delay (time after which the cpufreq governor will
try updating the frequency again) is currently calculated by multiplying
transition_latency (nsec) with LATENCY_MULTIPLIER (1000) and then
converting this time to usec. That gives the exact same value as
transition_latency, just that the time unit is usec instead of nsec.
With acpi-cpufreq for example, transition_latency is set to around 10
usec and we get transition delay as 10 ms. Which seems to be a
reasonable amount of time to reevaluate the frequency again.
But for platforms where frequency switching isn't that fast (like ARM),
the transition_latency varies from 500 usec to 3 ms, and the transition
delay becomes 500 ms to 3 seconds. Of course, that is a pretty bad
default value to start with.
We can try to come across a better formula (instead of multiplying with
LATENCY_MULTIPLIER) to solve this problem, but will that be worth it ?
This patch tries a simple approach and caps the maximum value of default
transition delay to 10 ms. Of course, userspace can still come in and
change this value anytime or individual drivers can rather provide
transition_delay_us instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We have moved the Ux500 over to use the generic DT based
cpufreq driver, so delete the old custom driver.
At the same time select CPUFREQ_DT from the machine's
Kconfig in order to satisfy the "default ARCH_U8500"
selection on the old driver.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This enables the generic DT and OPP-based cpufreq driver on the
ST-Ericsson Ux500 series.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
platform_device_id are not supposed to change at runtime. All functions
working with platform_device_id provided by <linux/platform_device.h>
work with const platform_device_id. So mark the non-const structs as
const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds the r8a7796 support the generic cpufreq driver
by adding an appropriate compat string. This is in keeping
with support for other Renesas ARM and arm64 based SoCs.
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@rvc.renesas.com>
[simon: new changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
policy->cpu is copied into policy->cpus in cpufreq_online() before
calling into cpufreq_driver->init(). So there's no need to set the
same in the individual driver init() functions again.
This patch removes the redundant setting of policy->cpu in policy->cpus
in intel_pstate and cppc drivers.
Reported-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The intel_pstate CPU frequency scaling driver has always
calculated CPU frequency incorrectly. Recent changes have
eliminted most of the issues, however the frequency reported
in the trace buffer, if used, is incorrect.
It remains desireable that cpu->pstate.scaling still be a nice
round number for things such as when setting max and min frequencies.
So the proposal is to just fix the reported frequency in the trace data.
Fixes what remains of [1].
Link: https://bugzilla.kernel.org/show_bug.cgi?id=96521 # [1]
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
MT7622 is a 64-bit ARMv8 based dual-core SoC (2 * Cortex-A53) with a
single cluster. The hardware is also compatible with the current driver,
so add MT7622 as one of the compatible string list.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since more MediaTek SoCs can be supported with the cpufreq driver and not
limited to MT8173, a couple of cleanups are done here with renaming those
functions and related structures with "mtk" instead of "mt8173".
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CPUFREQ_ENTRY_INVALID is a special symbol which is used to specify that
an entry in the cpufreq table is invalid. But using it outside of the
scope of the cpufreq table looks a bit incorrect.
We can represent an invalid frequency by writing it as 0 instead if we
need. Note that it is already done that way for the return value of the
->get() callback.
Lets do the same for ->fast_switch() and not use CPUFREQ_ENTRY_INVALID
outside of the scope of cpufreq table.
Also update the comment over cpufreq_driver_fast_switch() to clearly
mention what this returns.
None of the drivers return CPUFREQ_ENTRY_INVALID as of now from
->fast_switch() callback and so we don't need to update any of those.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The names of the INTEL_PSTATE_DEFAULT_SAMPLING_INTERVAL symbol and
the get_target_pstate_use_cpu_load() function don't need to be so
long any more, so make them shorter.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since there is only one P-state selection routine in intel_pstate
now, make intel_pstate_adjust_pstate() call it directly and drop
the target_pstate argument from that function.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After the commit "a399dc9fc50 cpufreq: shmobile: Use generic platdev
driver", will use cpufreq-dt-platdev driver to enable cpufreq-dt support.
Hence, follow the implementation to support new R8A7795 SoC.
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@rvc.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds the rk3328 compatible string for supporting
the generic cpufreq driver on RK3328.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the current implementation, the response latency between seeing
SCHED_CPUFREQ_IOWAIT set and the actual P-state adjustment can be up
to 10ms. It can be reduced by bumping up the P-state to the max at
the time SCHED_CPUFREQ_IOWAIT is passed to intel_pstate_update_util().
With this change, the IO performance improves significantly.
For a simple "grep -r . linux" (Here linux is the kernel source
folder) with caches dropped every time on a Broadwell Xeon workstation
with per-core P-states, the user and system time is shorter by as much
as 30% - 40%.
The same performance difference was not observed on clients that don't
support per-core P-state.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On many platforms, CPUs can do DVFS across cpufreq policies. i.e CPU
from policy-A can change frequency of CPUs belonging to policy-B.
This is quite common in case of ARM platforms where we don't
configure any per-cpu register.
Add a flag to identify such platforms and update
cpufreq_can_do_remote_dvfs() to allow remote callbacks if this flag is
set.
Also enable the flag for cpufreq-dt driver which is used only on ARM
platforms currently.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With Android UI and benchmarks the latency of cpufreq response to
certain scheduling events can become very critical. Currently, callbacks
into cpufreq governors are only made from the scheduler if the target
CPU of the event is the same as the current CPU. This means there are
certain situations where a target CPU may not run the cpufreq governor
for some time.
One testcase to show this behavior is where a task starts running on
CPU0, then a new task is also spawned on CPU0 by a task on CPU1. If the
system is configured such that the new tasks should receive maximum
demand initially, this should result in CPU0 increasing frequency
immediately. But because of the above mentioned limitation though, this
does not occur.
This patch updates the scheduler core to call the cpufreq callbacks for
remote CPUs as well.
The schedutil, ondemand and conservative governors are updated to
process cpufreq utilization update hooks called for remote CPUs where
the remote CPU is managed by the cpufreq policy of the local CPU.
The intel_pstate driver is updated to always reject remote callbacks.
This is tested with couple of usecases (Android: hackbench, recentfling,
galleryfling, vellamo, Ubuntu: hackbench) on ARM hikey board (64 bit
octa-core, single policy). Only galleryfling showed minor improvements,
while others didn't had much deviation.
The reason being that this patch only targets a corner case, where
following are required to be true to improve performance and that
doesn't happen too often with these tests:
- Task is migrated to another CPU.
- The task has high demand, and should take the target CPU to higher
OPPs.
- And the target CPU doesn't call into the cpufreq governor until the
next tick.
Based on initial work from Steve Muckle.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit 62611cb912 (intel_pstate: delete scheduler hook in HWP
mode) the INTEL_PSTATE_HWP_SAMPLING_INTERVAL is not used anywhere in
the code, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ->get callback in the intel_pstate structure was mostly there
for the scaling_cur_freq sysfs attribute to work, but after commit
f8475cef90 (x86: use common aperfmperf_khz_on_cpu() to calculate
KHz using APERF/MPERF) that attribute uses arch_freq_get_on_cpu()
provided by the x86 arch code on all processors supported by
intel_pstate, so it doesn't need the ->get callback from the
driver any more.
Moreover, the very presence of the ->get callback in the intel_pstate
structure causes the cpuinfo_cur_freq attribute to be present when
intel_pstate operates in the active mode, which is bogus, because
the role of that attribute is to return the current CPU frequency
as seen by the hardware. For intel_pstate, though, this is just an
average frequency and not really current, but computed for the
previous sampling interval (the actual current frequency may be
way different at the point this value is obtained by reading from
cpuinfo_cur_freq), and after commit 82b4e03e01 (intel_pstate: skip
scheduler hook when in "performance" mode) the value in
cpuinfo_cur_freq may be stale or just 0, depending on the driver's
operation mode. In fact, however, on the hardware supported by
intel_pstate there is no way to read the current CPU frequency
from it, so the cpuinfo_cur_freq attribute should not be present
at all when this driver is in use.
For this reason, drop intel_pstate_get() and clear the ->get
callback pointer pointing to it, so that the cpuinfo_cur_freq is
not present for intel_pstate in the active mode any more.
Fixes: 82b4e03e01 (intel_pstate: skip scheduler hook when in "performance" mode)
Reported-by: Huaisheng Ye <yehs1@lenovo.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
for_each_compatible_node performs an of_node_get on each iteration, so a
return from the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression n;
expression e,e1,e2;
statement S;
iterator i1;
iterator name for_each_compatible_node;
@@
for_each_compatible_node(n,e1,e2) {
...
(
of_node_put(n);
|
e = n
|
return n;
|
i1(...,n,...) S
|
+ of_node_put(n);
? return ...;
)
...
}
// </smpl>
Additionally, call of_node_put on the previous value of np, obtained from
of_find_compatible_node, that is no longer accessible at the point of the
for_each_compatible_node.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
All systems use the same P-state selection "powersave" algorithm
in the active mode if HWP is not used, so there's no need to provide
a pointer for it in struct pstate_funcs any more.
Drop ->update_util from struct pstate_funcs and make
intel_pstate_set_update_util_hook() use intel_pstate_update_util()
directly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
All systems with a defined ACPI preferred profile that are not
"servers" have been using the load-based P-state selection algorithm
in intel_pstate since 4.12-rc1 (mobile systems and laptops have been
using it since 4.10-rc1) and no problems with it have been reported
to date. In particular, no regressions with respect to the PID-based
P-state selection have been reported. Also testing indicates that
the P-state selection algorithm based on CPU load is generally on par
with the PID-based algorithm performance-wise, and for some workloads
it turns out to be better than the other one, while being more
straightforward and easier to understand at the same time.
Moreover, the PID-based P-state selection algorithm in intel_pstate
is known to be unstable in some situation and generally problematic,
the issues with it are hard to address and it has become a
significant maintenance burden.
For these reasons, make intel_pstate use the "powersave" P-state
selection algorithm based on CPU load in the active mode on all
systems and drop the PID-based P-state selection code along with
all things related to it from the driver. Also update the
documentation accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With the recent updates, CPUFREQ_ETERNAL is only used by the drivers
which don't know their transition latency but want to use dynamic
switching.
Anyway, the routine cpufreq_policy_transition_delay_us() caps the value
of transition latency to 10 ms now and that can be used safely with such
platforms.
Remove the check from cpufreq_init_governor() and allow dynamic
switching for such configurations as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The policy->transition_latency field is used for multiple purposes
today and its not straight forward at all. This is how it is used:
A. Set the correct transition_latency value.
B. Set it to CPUFREQ_ETERNAL because:
1. We don't want automatic dynamic switching (with
ondemand/conservative) to happen at all.
2. We don't know the transition latency.
This patch handles the B.1. case in a more readable way. A new flag for
the cpufreq drivers is added to disallow use of cpufreq governors which
have dynamic_switching flag set.
All the current cpufreq drivers which are setting transition_latency
unconditionally to CPUFREQ_ETERNAL are updated to use it. They don't
need to set transition_latency anymore.
There shouldn't be any functional change after this patch.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no limitation in the ondemand or conservative governors which
disallow the transition_latency to be greater than 10 ms.
The max_transition_latency field is rather used to disallow automatic
dynamic frequency switching for platforms which didn't wanted these
governors to run.
Replace max_transition_latency with a boolean (dynamic_switching) and
check for transition_latency == CPUFREQ_ETERNAL along with that. This
makes it pretty straight forward to read/understand now.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
All users of arm_big_little driver are defining it and there is no need
to keep it optional.
Make it mandatory to remove the always true conditional statement.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The transition_latency field isn't used for drivers with ->setpolicy()
callback present and there is no point setting it from the drivers.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The policy->transition_delay_us field is used only by the schedutil
governor currently, and this field describes how fast the driver wants
the cpufreq governor to change CPUs frequency. It should rather be a
common thing across all governors, as it doesn't have any schedutil
dependency here.
Create a new helper cpufreq_policy_transition_delay_us() to get the
transition delay across all governors.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core and governors aren't supposed to set a limit on how
fast we want to try changing the frequency. This is currently done for
the legacy governors with help of min_sampling_rate.
At worst, we may end up setting the sampling rate to a value lower than
the rate at which frequency can be changed and then one of the CPUs in
the policy will be only changing frequency for ever.
But that is something for the user to decide and there is no need to
have special handling for such cases in the core. Leave it for the user
to figure out.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On tango platforms, firmware configures the CPU clock, and Linux is
then only allowed to use the cpu_clk_divider to change the frequency.
Build the OPP table dynamically at init, in order to support whatever
firmware throws at us.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
MT2701/MT7623 is a 32-bit ARMv7 based quad-core (4 * Cortex-A7) with
single cluster and this hardware is also compatible with the existing
driver through enabling CPU frequency feature with operating-points-v2
bindings. Also, this driver actually supports all MediaTek SoCs, the
Kconfig menu entry and file name itself should be updated with more
generic name to drop "MT8173"
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add zynqmp to the cpufreq dt platform device.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove unnecessary static on local variable hostbridge.
Such variable is initialized before being used,
on every execution path throughout the function.
The static has no benefit and, removing it reduces
the code size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see the difference in the code size. Also,
there is a significant difference in the bss segment. This log is the
output of the size command, before and after the code change:
before:
text data bss dec hex filename
5084 3392 256 8732 221c drivers/cpufreq/speedstep-ich.o
after:
text data bss dec hex filename
5062 3304 192 8558 216e drivers/cpufreq/speedstep-ich.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Avoid clearing the PCI PME Enable bit for devices as a result of
config space restoration which confuses AML executed afterward and
causes wakeup events to be lost on some systems (Rafael Wysocki).
- Fix the native PCIe PME interrupts handling in the cases when the
PME IRQ is set up as a system wakeup one so that runtime PM remote
wakeup works as expected after system resume on systems where that
happens (Rafael Wysocki).
- Fix the device PM QoS sysfs interface to handle invalid user input
correctly instead of using an unititialized variable value as the
latency tolerance for the device at hand (Dan Carpenter).
- Get rid of one more rounding error from intel_pstate computations
(Srinivas Pandruvada).
- Fix the schedutil cpufreq governor to prevent it from possibly
accessing unititialized data structures from governor callbacks in
some cases on systems when multiple CPUs share a single cpufreq
policy object (Vikram Mulukutla).
- Fix the return values of probe routines in two devfreq drivers
(Gustavo Silva).
- Constify an attribute_group structure in devfreq (Arvind Yadav).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=G9eQ
-----END PGP SIGNATURE-----
Merge tag 'pm-fixes-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a recently exposed issue in the PCI device wakeup code and
one older problem related to PCI device wakeup that has been reported
recently, modify one more piece of computations in intel_pstate to get
rid of a rounding error, fix a possible race in the schedutil cpufreq
governor, fix the device PM QoS sysfs interface to correctly handle
invalid user input, fix return values of two probe routines in devfreq
drivers and constify an attribute_group structure in devfreq.
Specifics:
- Avoid clearing the PCI PME Enable bit for devices as a result of
config space restoration which confuses AML executed afterward and
causes wakeup events to be lost on some systems (Rafael Wysocki).
- Fix the native PCIe PME interrupts handling in the cases when the
PME IRQ is set up as a system wakeup one so that runtime PM remote
wakeup works as expected after system resume on systems where that
happens (Rafael Wysocki).
- Fix the device PM QoS sysfs interface to handle invalid user input
correctly instead of using an unititialized variable value as the
latency tolerance for the device at hand (Dan Carpenter).
- Get rid of one more rounding error from intel_pstate computations
(Srinivas Pandruvada).
- Fix the schedutil cpufreq governor to prevent it from possibly
accessing unititialized data structures from governor callbacks in
some cases on systems when multiple CPUs share a single cpufreq
policy object (Vikram Mulukutla).
- Fix the return values of probe routines in two devfreq drivers
(Gustavo Silva).
- Constify an attribute_group structure in devfreq (Arvind Yadav)"
* tag 'pm-fixes-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PCI / PM: Fix native PME handling during system suspend/resume
PCI / PM: Restore PME Enable after config space restoration
cpufreq: schedutil: Fix sugov_start() versus sugov_update_shared() race
PM / QoS: return -EINVAL for bogus strings
cpufreq: intel_pstate: Fix ratio setting for min_perf_pct
PM / devfreq: constify attribute_group structures.
PM / devfreq: tegra: fix error return code in tegra_devfreq_probe()
PM / devfreq: rk3399_dmc: fix error return code in rk3399_dmcfreq_probe()
Pull thermal management updates from Zhang Rui:
- Improve thermal cpu_cooling interaction with cpufreq core.
The cpu_cooling driver is designed to use CPU frequency scaling to
avoid high thermal states for a platform. But it wasn't glued really
well with cpufreq core.
For example clipped-cpus is copied from the policy structure and its
much better to use the policy->cpus (or related_cpus) fields directly
as they may have got updated. Not that things were broken before this
series, but they can be optimized a bit more.
This series tries to improve interactions between cpufreq core and
cpu_cooling driver and does some fixes/cleanups to the cpu_cooling
driver. (Viresh Kumar)
- A couple of fixes and cleanups in thermal core and imx, hisilicon,
bcm_2835, int340x thermal drivers. (Arvind Yadav, Dan Carpenter,
Sumeet Pawnikar, Srinivas Pandruvada, Willy WOLFF)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (24 commits)
thermal: bcm2835: fix an error code in probe()
thermal: hisilicon: Handle return value of clk_prepare_enable
thermal: imx: Handle return value of clk_prepare_enable
thermal: int340x: check for sensor when PTYP is missing
Thermal/int340x: Fix few typos and kernel-doc style
thermal: fix source code documentation for parameters
thermal: cpu_cooling: Replace kmalloc with kmalloc_array
thermal: cpu_cooling: Rearrange struct cpufreq_cooling_device
thermal: cpu_cooling: 'freq' can't be zero in cpufreq_state2power()
thermal: cpu_cooling: don't store cpu_dev in cpufreq_cdev
thermal: cpu_cooling: get_level() can't fail
thermal: cpu_cooling: create structure for idle time stats
thermal: cpu_cooling: merge frequency and power tables
thermal: cpu_cooling: get rid of 'allowed_cpus'
thermal: cpu_cooling: OPPs are registered for all CPUs
thermal: cpu_cooling: store cpufreq policy
cpufreq: create cpufreq_table_count_valid_entries()
thermal: cpu_cooling: use cpufreq_policy to register cooling device
thermal: cpu_cooling: get rid of a variable in cpufreq_set_cur_state()
thermal: cpu_cooling: remove cpufreq_cooling_get_level()
...
The busy percent calculated for the Knights Landing (KNL) platform
is 1024 times smaller than the correct busy value. This causes
performance to get stuck at the lowest ratio.
The scaling algorithm used for KNL is performance-based, but it still
looks at the CPU load to set the scaled busy factor to 0 when the
load is less than 1 percent. In this case, since the computed load
is 1024x smaller than it should be, the scaled busy factor will
always be 0, irrespective of CPU business.
This needs a fix similar to the turbostat one in commit b2b34dfe4d
(tools/power turbostat: KNL workaround for %Busy and Avg_MHz).
For this reason, add one more callback to processor-specific
callbacks to specify an MPERF multiplier represented by a number of
bit positions to shift the value of that register to the left to
copmensate for its rate difference with respect to the TSC. This
shift value is used during CPU busy calculations.
Fixes: ffb810563c (intel_pstate: Avoid getting stuck in high P-states when idle)
Reported-and-tested-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 4.6+ <stable@vger.kernel.org> # 4.6+
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When the minimum performance limit percentage is set to the power-up
default, it is possible that minimum performance ratio is off by one.
In the set_policy() callback the minimum ratio is calculated by
applying global.min_perf_pct to turbo_ratio and rounding up, but the
power-up default global.min_perf_pct is already rounded up to the
next percent in min_perf_pct_min(). That results in two round up
operations, so for the default min_perf_pct one of them is not
required.
It is better to remove rounding up in min_perf_pct_min() as this
matches the displayed min_perf_pct prior to commit c5a2ee7dde
(cpufreq: intel_pstate: Active mode P-state limits rework) in 4.12.
For example on a platform with max turbo ratio of 37 and minimum
ratio of 10, the min_perf_pct resulted in 28 with the above commit.
Before this commit it was 27 and it will be the same after this
change.
Fixes: 1a4fe38add (cpufreq: intel_pstate: Remove max/min fractions to limit performance)
Reported-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Revert a recent change in the generic power domains (genpd)
framework that led to regressions and turned out the be misguided
(Rafael Wysocki).
- Fix a recently introduced build issue in the generic power domains
(genpd) framework (Arnd Bergmann).
- Constify attribute_group structures in the PM core, the cpufreq
stats code and in intel_pstate (Arvind Yadav).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=B+R7
-----END PGP SIGNATURE-----
Merge tag 'pm-extra-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These revert one recent change in the generic power domains
framework, fix a recently introduced build issue in there and
constify attribute_group structures in some places.
Specifics:
- Revert a recent change in the generic power domains (genpd)
framework that led to regressions and turned out the be misguided
(Rafael Wysocki).
- Fix a recently introduced build issue in the generic power domains
(genpd) framework (Arnd Bergmann).
- Constify attribute_group structures in the PM core, the cpufreq
stats code and in intel_pstate (Arvind Yadav)"
* tag 'pm-extra-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: constify attribute_group structures
cpufreq: cpufreq_stats: constify attribute_group structures
PM / sleep: constify attribute_group structures
PM / Domains: provide pm_genpd_poweroff_noirq() stub
Revert "PM / Domains: Handle safely genpd_syscore_switch() call on non-genpd device"
- New SoC specific drivers
- NVIDIA Tegra PM Domain support for newer SoCs (Tegra186 and later)
based on the "BPMP" firmware
- Clocksource and system controller drivers for the newly added
Action Semi platforms (both arm and arm64).
- Reset subsystem, merged through arm-soc by tradition:
- New drivers for Altera Stratix10, TI Keystone and Cortina Gemini SoCs
- Various subsystem-wide cleanups
- Updates for existing SoC-specific drivers
- TI GPMC (General Purpose Memory Controller)
- Mediatek "scpsys" system controller support for MT6797
- Broadcom "brcmstb_gisb" bus arbitrer
- ARM SCPI firmware
- Renesas "SYSC" system controller
One more driver update was submitted for the Freescale/NXP DPAA
data path acceleration that has previously been used on PowerPC
chips. I ended up postponing the merge until some API questions
for its unusual MMIO access are resolved.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5L6n
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"New SoC specific drivers:
- NVIDIA Tegra PM Domain support for newer SoCs (Tegra186 and later)
based on the "BPMP" firmware
- Clocksource and system controller drivers for the newly added
Action Semi platforms (both arm and arm64).
Reset subsystem, merged through arm-soc by tradition:
- New drivers for Altera Stratix10, TI Keystone and Cortina Gemini
SoCs
- Various subsystem-wide cleanups
Updates for existing SoC-specific drivers
- TI GPMC (General Purpose Memory Controller)
- Mediatek "scpsys" system controller support for MT6797
- Broadcom "brcmstb_gisb" bus arbitrer
- ARM SCPI firmware
- Renesas "SYSC" system controller
One more driver update was submitted for the Freescale/NXP DPAA data
path acceleration that has previously been used on PowerPC chips. I
ended up postponing the merge until some API questions for its unusual
MMIO access are resolved"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
clocksource: owl: Add S900 support
clocksource: Add Owl timer
soc: renesas: rcar-sysc: Use GENPD_FLAG_ALWAYS_ON
firmware: tegra: Fix locking bugs in BPMP
soc/tegra: flowctrl: Fix error handling
soc/tegra: bpmp: Implement generic PM domains
soc/tegra: bpmp: Update ABI header
PM / Domains: Allow overriding the ->xlate() callback
soc: brcmstb: enable drivers for ARM64 and BMIPS
soc: renesas: Rework Kconfig and Makefile logic
reset: Add the TI SCI reset driver
dt-bindings: reset: Add TI SCI reset binding
reset: use kref for reference counting
soc: qcom: smsm: Improve error handling, quiesce probe deferral
cpufreq: scpi: use new scpi_ops functions to remove duplicate code
firmware: arm_scpi: add support to populate OPPs and get transition latency
dt-bindings: reset: Add reset manager offsets for Stratix10
memory: omap-gpmc: add error message if bank-width property is absent
memory: omap-gpmc: make dts snippet include semicolon
reset: Add a Gemini reset controller
...
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for
the Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that
can wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which
allows the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of
RCU which doesn't allow sleeping in the read-side critical
sections, but which in turn is expected to be allowed by the
IRQ bus locking infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance"
P-state selection algorithm is in use by making it avoid
registering scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in
intel_pstate by changing the values that correspond to
different symbolic hint names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1
on AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the
imx6q driver and clean up the sfi, exynos5440 and intel_pstate
drivers (Colin Ian King, Krzysztof Kozlowski, Octavian Purdila,
Rafael Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski,
Mikko Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix
a minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Wsph
-----END PGP SIGNATURE-----
Merge tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The big ticket items here are the rework of suspend-to-idle in order
to add proper support for power button wakeup from it on recent Dell
laptops and the rework of interfaces exporting the current CPU
frequency on x86.
In addition to that, support for a few new pieces of hardware is
added, the PCI/ACPI device wakeup infrastructure is simplified
significantly and the wakeup IRQ framework is fixed to unbreak the IRQ
bus locking infrastructure.
Also, there are some functional improvements for intel_pstate, tools
updates and small fixes and cleanups all over.
Specifics:
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for the
Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that can
wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which allows
the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of RCU
which doesn't allow sleeping in the read-side critical sections,
but which in turn is expected to be allowed by the IRQ bus locking
infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance" P-state
selection algorithm is in use by making it avoid registering
scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in intel_pstate
by changing the values that correspond to different symbolic hint
names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1 on
AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the imx6q
driver and clean up the sfi, exynos5440 and intel_pstate drivers
(Colin Ian King, Krzysztof Kozlowski, Octavian Purdila, Rafael
Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski, Mikko
Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix a
minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski)"
* tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (69 commits)
cpufreq: Update scaling_cur_freq documentation
cpufreq: intel_pstate: Clean up after performance governor changes
PM: hibernate: constify attribute_group structures.
cpuidle: menu: allow state 0 to be disabled
intel_idle: Use more common logging style
PM / Domains: Fix missing default_power_down_ok comment
PM / Domains: Fix unsafe iteration over modified list of domains
PM / Domains: Fix unsafe iteration over modified list of domain providers
PM / Domains: Fix unsafe iteration over modified list of device links
PM / Domains: Handle safely genpd_syscore_switch() call on non-genpd device
PM / Domains: Call driver's noirq callbacks
PM / core: Drop run_wake flag from struct dev_pm_info
PCI / PM: Simplify device wakeup settings code
PCI / PM: Drop pme_interrupt flag from struct pci_dev
ACPI / PM: Consolidate device wakeup settings code
ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
PM / QoS: constify *_attribute_group.
PM / AVS: rockchip-io: add io selectors and supplies for rk3228
powercap/RAPL: prevent overridding bits outside of the mask
PM / sysfs: Constify attribute groups
...
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
15197 2552 40 17789 457d drivers/cpufreq/intel_pstate.o
File size After adding 'const':
text data bss dec hex filename
15261 2488 40 17789 457d drivers/cpufreq/intel_pstate.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
1655 256 4 1915 77b drivers/cpufreq/cpufreq_stats.o
File size After adding 'const':
text data bss dec hex filename
1695 192 4 1891 763 drivers/cpufreq/cpufreq_stats.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull SMP hotplug updates from Thomas Gleixner:
"This update is primarily a cleanup of the CPU hotplug locking code.
The hotplug locking mechanism is an open coded RWSEM, which allows
recursive locking. The main problem with that is the recursive nature
as it evades the full lockdep coverage and hides potential deadlocks.
The rework replaces the open coded RWSEM with a percpu RWSEM and
establishes full lockdep coverage that way.
The bulk of the changes fix up recursive locking issues and address
the now fully reported potential deadlocks all over the place. Some of
these deadlocks have been observed in the RT tree, but on mainline the
probability was low enough to hide them away."
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
cpu/hotplug: Constify attribute_group structures
powerpc: Only obtain cpu_hotplug_lock if called by rtasd
ARM/hw_breakpoint: Fix possible recursive locking for arch_hw_breakpoint_init
cpu/hotplug: Remove unused check_for_tasks() function
perf/core: Don't release cred_guard_mutex if not taken
cpuhotplug: Link lock stacks for hotplug callbacks
acpi/processor: Prevent cpu hotplug deadlock
sched: Provide is_percpu_thread() helper
cpu/hotplug: Convert hotplug locking to percpu rwsem
s390: Prevent hotplug rwsem recursion
arm: Prevent hotplug rwsem recursion
arm64: Prevent cpu hotplug rwsem recursion
kprobes: Cure hotplug lock ordering issues
jump_label: Reorder hotplug lock and jump_label_lock
perf/tracing/cpuhotplug: Fix locking order
ACPI/processor: Use cpu_hotplug_disable() instead of get_online_cpus()
PCI: Replace the racy recursion prevention
PCI: Use cpu_hotplug_disable() instead of get_online_cpus()
perf/x86/intel: Drop get_online_cpus() in intel_snb_check_microcode()
x86/perf: Drop EXPORT of perf_check_microcode
...
* pm-cpufreq:
cpufreq / CPPC: Initialize policy->min to lowest nonlinear performance
cpufreq: sfi: make freq_table static
cpufreq: exynos5440: Fix inconsistent indenting
cpufreq: imx6q: imx6ull should use the same flow as imx6ul
cpufreq: dt: Add support for hi3660
* intel_pstate:
cpufreq: Update scaling_cur_freq documentation
cpufreq: intel_pstate: Clean up after performance governor changes
intel_pstate: skip scheduler hook when in "performance" mode
intel_pstate: delete scheduler hook in HWP mode
x86: use common aperfmperf_khz_on_cpu() to calculate KHz using APERF/MPERF
cpufreq: intel_pstate: Remove max/min fractions to limit performance
x86: do not use cpufreq_quick_get() for /proc/cpuinfo "cpu MHz"
* pm-cpuidle:
cpuidle: menu: allow state 0 to be disabled
intel_idle: Use more common logging style
x86/ACPI/cstate: Allow ACPI C1 FFH MWAIT use on AMD systems
ARM: cpuidle: Support asymmetric idle definition
Rafael J. Wysocki