When multiple headphone pins are defined without line-out pins, the
driver takes them as primary outputs. But it forgot to set line_out_type
to HP by assuming there is some rest of HP pins. This results in some
mis-handling of these pins for Realtek codec parser. It takes as if
these are pure line-out jacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
When a mixer control element was already created with the given name,
try to find another index for avoiding conflicts, instead of breaking
with an error. This makes the driver more robust.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The sticky PCM stream assignment introduced in 2.6.36 kernel seems
causing problems on AD codecs. At some time later, the streaming no
longer works by unknown reason. A simple workaround is to disable
sticky-assignment for these codecs.
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Creative IBG controllers require the playback stream-tags to be started
from 1, instead of capture+1. Otherwise the stream stalls.
Reported-by: Wai Yew CHAY <wychay@ctl.creative.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HDA specification does not allow for a codec to mute itself just
because the volume is reduced, so _of course_ somebody had to go and do
it. This wouldn'\''t hurt too much when the volume is adjusted by hand,
but programs like PA that try to set the volume automatically could
inadvertently mute the output.
To work around this, change the TLV dB information for the Master volume
on all Sigmatel HDA codecs to indicate the the minimal volume setting
actually mutes.
Reported-by: Colin Guthrie <gmane@colin.guthr.ie>
Reported-by: "Alexander E. Patrakov" <patrakov@gmail.com>
Tested-by: Colin Guthrie <cguthrie@mandriva.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the explicit ifdef check and call of check_power_status ops with
a new helper function, hda_call_check_power_status().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make the helper function to give the input-pin attribute for jack
connectivity and location. This simplifies checks of input-pin jacks
a bit in some places.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the mic pins are assigned to the same location, we can omit the
redundant location prefix like "Front" or "Rear".
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch improves the input-source label strings to be generated from
the pin information instead of fixed strings per AUTO_PIN_* type.
This gives more suitable labels, especially for mic and line-in pins.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We can assign multiple pins to a single role now, let's reduce the
redundant FRONT_MIC and FRONT_LINE. Also, autocfg->input_pins[] is
no longer used, so this is removed as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Keep char array in the input_mux item itself instead of pointing to
an external string. This is a preliminary work for improving the
input-mux name based on the pin role.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In snd_hda_parse_def_config(), some unused values may remain in hp_pins[]
array during the headphone-reassignment workaround. This patch clears
the unused array members.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hda_parse_pin_def_config() has some workaround for re-assigning
some pins declared as headphones to line-outs. This didn't work properly
for some cases because it used memmove() stupidly wrongly.
Reference: Novell bnc#637263
https://bugzilla.novell.com/show_bug.cgi?id=637263
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added snd_hda_get_input_pin_label() helper function to return the
string that can be used for control or capture-source ids.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the new fields to contain all input-pins to struct auto_pin_cfg.
Unlike the existing input_pins[], this array contains all input pins
even if the multiple pins are assigned for a single role (i.e. two
front mics). The former input_pins[] still remains for a while, but
will be removed in near future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new sticky PCM parameter introduced the delayed clean-ups of
stream- and channel-id tags. In the current implementation, this check
(adding dirty flag) and actual clean-ups are done only for the codec
chip. However, with HD-audio architecture, multiple codecs can be
on a single bus, and the controller assign stream- and channel-ids in
the bus-wide.
In this patch, the stream-id and channel-id are checked over all codecs
connected to the corresponding bus. Together with it, the mutex is
moved to struct hda_bus, as this becomes also bus-wide.
Reported-and-tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit eb541337b7
ALSA: hda - Make converter setups sticky
changes the semantics of snd_hda_codec_cleanup_stream() not to clean up
the stream at that moment but delay the action. This broke the codes
expecting that the clean-up is done immediately, such as dynamic ADC
changes in some codec drivers.
This patch fixes the issue by introducing a lower helper,
__snd_hda_codec_cleanup_stream(), to allow the immediate clean up.
The original snd_hda_codec_cleanup_stream() is kept as is now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, we reset the converter setups like the stream-tag, the
channel-id and format-id in prepare callbacks, and clear them in
cleanup callbacks. This often causes a silence of the digital
receiver for a couple of seconds.
This patch tries to delay the converter setup changes as much as
possible. The converter setups are cached and aren't reset as long
as the same values are used. At suspend/resume, they are cleared
to be recovered properly, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set bit 15 (Stream Type) of HDA Stream Format to 1 (Non-PCM) when IEC958
channel status bit 1 (AES0 & 0x02) is set to 1 (non-audio).
This is a prequisite for HDMI HBR passthrough.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit afbd9b8448
ALSA: hda - Limit the amp value to write
introduced a regression for codec setups with amp offsets like IDT/STAC
codecs. The limit value should be a raw value without offset calculation.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The function IDs are different for audio and modem. Do not mix them.
Also, show the unsolicited bit in the function_id register.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Check the amp max value at put callbacks and set the upper limit
so that the driver won't write any invalid value over the defined
range.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Many codecs now clear the pin controls at suspend via snd_hda_shutup_pins()
for reducing the click noise at power-off. But this leaves some pins
uninitialized, and they'll be never recovered after resume.
This patch adds the proper recovery of cleared pin controls on resume.
Also it adds a check of bus->shutdown so that pins won't be cleared at
module unloading.
Reference: Kernel bug 16339
http://bugzilla.kernel.org/show_bug.cgi?id=16339
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new helper, snd_hda_codec_update_cache(), for reducing the unneeded
verbs. This function checks the cached value and skips if it's identical
with the given one. Otherwise it works like snd_hda_codec_write_cache().
The alc269 code uses this function as an example.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add new check for MIC. Do the internal DMIC as the Front MIC.
It could solve the default record source index issue.
[Fix the check properly using the bitmask by tiwai]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add an error message to snd_hda_add_nid() for invalid mapping NID to make
easier to hunt the buggy code.
Also added a missing space to the error message in snd_hda_build_controls()
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This will save ~15ms boot time.
The first 10ms sleep was introduced in commit d2595d86e5 for (buggy)
Cxt codecs, so better to limit the sleep to the problem hardware.
For the second 10ms sleep, the HDA spec says:
Power State[1:0]:
00: Node Power state (D0) is fully on.
01: Node Power state (D1) allows for (does not require) the lowest possible power consuming state from which it
can return to the "fully on" state (D0) within 10 ms, excepting analog pass through circuits (e.g., CD analog
playback) which must remain fully on.
10: Node Power state (D2) allows for (does not require) the lowest possible power consuming state from which it
can return to the "fully on" state (D0) within 10 ms. For modems, this is the "wake on ring" power state.
11: Node Power state (D3) allows for (does not require) lowest possible power consuming state under software
control. Note that any low power state set by software must retain sufficient operational capability to properly
respond to subsequent software Power State command.
So 10ms is actually the max wait time. It should be safe to
remove/reduce it and rely on the loop of 1ms-sleeps.
CC: Marc Boucher <marc@linuxant.com>
CC: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a common helper function for clearing pin controls before suspend.
Use the pincfg array instead of looking through all widget tree.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Analog Device codecs seem to have problems with the triggering of
pin-sensing although their pincaps give the trigger requirements.
Some reported that constant CPU load on HP laptops with AD codecs.
For avoiding this regression, add a flag to codec struct to notify
explicitly that the codec doesn't suppot the trigger at pin-sensing.
Tested-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Postpone the mixer name setup after the codec patch since the codec
patch may change the codec name string in itself.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the wrong implementation of NID <-> kctl mapping for capture mixers
introduced by the ocmmit 5b0cb1d850.
So far, the driver returns an error at probe.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HDA_SUBDEV_NID_FLAG is duplicate for amplifier control elements. Move
get_amp_nid_() call to the snd_hda_ctl_add() function.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The purpose of this changeset is to show information about amplifier
setting in the codec proc file. Something like:
Control: name="Front Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Control: name="Front Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=2, ofs=0
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Takashi Iwai