-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAmHhw7oTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXrjSB/979LV4Dn1PMcFYsSdlFEMeHcjzJdw/
kFnLPXMaPJyfg6QPuf83jxzw9uxw8fcePMdVq/FFBtmVV9fJMAv62B8jaGS1p58c
WnAg+7zsTN+xEoJn+tskSSon8BNMWVrl41zP3K4Ged+5j8UEBk62GB8Orz1qkpwL
fTh3/+xAvczJeD4zZb1dAm4WnmcQJ4vhg45p07jX6owvnwQAikMFl45aSW54I5o8
vAxGzFgdsZ2NtExnRNKh3b3DozA8JUE89KckBSZnDtq4rH8Fyy6Wij56Hc6v6Cml
SUohiNbHX7hsNwit/lxL8wuF97IiA0pQSABobEg3rxfTghTUep51LlaN
=/m4A
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed-20220114' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv updates from Wei Liu:
- More patches for Hyper-V isolation VM support (Tianyu Lan)
- Bug fixes and clean-up patches from various people
* tag 'hyperv-next-signed-20220114' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
scsi: storvsc: Fix storvsc_queuecommand() memory leak
x86/hyperv: Properly deal with empty cpumasks in hyperv_flush_tlb_multi()
Drivers: hv: vmbus: Initialize request offers message for Isolation VM
scsi: storvsc: Fix unsigned comparison to zero
swiotlb: Add CONFIG_HAS_IOMEM check around swiotlb_mem_remap()
x86/hyperv: Fix definition of hv_ghcb_pg variable
Drivers: hv: Fix definition of hypercall input & output arg variables
net: netvsc: Add Isolation VM support for netvsc driver
scsi: storvsc: Add Isolation VM support for storvsc driver
hyper-v: Enable swiotlb bounce buffer for Isolation VM
x86/hyper-v: Add hyperv Isolation VM check in the cc_platform_has()
swiotlb: Add swiotlb bounce buffer remap function for HV IVM
In Isolation VM, all shared memory with host needs to mark visible
to host via hvcall. vmbus_establish_gpadl() has already done it for
netvsc rx/tx ring buffer. The page buffer used by vmbus_sendpacket_
pagebuffer() stills need to be handled. Use DMA API to map/umap
these memory during sending/receiving packet and Hyper-V swiotlb
bounce buffer dma address will be returned. The swiotlb bounce buffer
has been masked to be visible to host during boot up.
rx/tx ring buffer is allocated via vzalloc() and they need to be
mapped into unencrypted address space(above vTOM) before sharing
with host and accessing. Add hv_map/unmap_memory() to map/umap rx
/tx ring buffer.
Signed-off-by: Tianyu Lan <Tianyu.Lan@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20211213071407.314309-6-ltykernel@gmail.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding comment to avoid the misusing of netvsc_xdp_xmit().
Otherwise the value of skb->queue_mapping could be 0 and
then the return value of skb_get_rx_queue() could be MAX_U16
cause by overflow.
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/1634174786-1810351-1-git-send-email-jiasheng@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use netif_is_bond_master() function instead of open code, which is
((event_dev->priv_flags & IFF_BONDING) && (event_dev->flags & IFF_MASTER)).
This patch doesn't change logic.
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert sw drivers from memcpy(... ETH_ADDR) to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set needed_headroom according to VF if VF needs a bigger
headroom.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the netvsc/VF binding logic only checks the PCI serial number.
The Microsoft Azure Network Adapter (MANA) supports multiple net_device
interfaces (each such interface is called a "vPort", and has its unique
MAC address) which are backed by the same VF PCI device, so the binding
logic should check both the MAC address and the PCI serial number.
The change should not break any other existing VF drivers, because
Hyper-V NIC SR-IOV implementation requires the netvsc network
interface and the VF network interface have the same MAC address.
Co-developed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Co-developed-by: Shachar Raindel <shacharr@microsoft.com>
Signed-off-by: Shachar Raindel <shacharr@microsoft.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is only one place where we want to specify new_ifindex. In all
other cases, callers pass 0 as new_ifindex. It looks reasonable to add a
low-level function with new_ifindex and to convert
dev_change_net_namespace to a static inline wrapper.
Fixes: eeb85a14ee ("net: Allow to specify ifindex when device is moved to another namespace")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we can specify ifindex on link creation. This change allows
to specify ifindex when a device is moved to another network namespace.
Even now, a device ifindex can be changed if there is another device
with the same ifindex in the target namespace. So this change doesn't
introduce completely new behavior, it adds more control to the process.
CRIU users want to restore containers with pre-created network devices.
A user will provide network devices and instructions where they have to
be restored, then CRIU will restore network namespaces and move devices
into them. The problem is that devices have to be restored with the same
indexes that they have before C/R.
Cc: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com>
Suggested-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Reviewed-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add error handling in case of failure to send switching data path message
to the host.
Reported-by: Shachar Raindel <shacharr@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace instances of sprintf or memcpy with a pointer update with
ethtool_sprintf.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Contrary to the RNDIS protocol specification, certain (pre-Fe)
implementations of Hyper-V's vSwitch did not account for the status
buffer field in the length of an RNDIS packet; the bug was fixed in
newer implementations. Validate the status buffer fields using the
length of the 'vmtransfer_page' packet (all implementations), that
is known/validated to be less than or equal to the receive section
size and not smaller than the length of the RNDIS message.
Reported-by: Dexuan Cui <decui@microsoft.com>
Suggested-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Fixes: 505e3f00c3 ("hv_netvsc: Add (more) validation for untrusted Hyper-V values")
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointers to receive-buffer packets sent by Hyper-V are used within the
guest VM. Hyper-V can send packets with erroneous values or modify
packet fields after they are processed by the guest. To defend against
these scenarios, copy (sections of) the incoming packet after validating
their length and offset fields in netvsc_filter_receive(). In this way,
the packet can no longer be modified by the host.
Reported-by: Juan Vazquez <juvazq@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Link: https://lore.kernel.org/r/20210126162907.21056-1-parri.andrea@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For additional robustness in the face of Hyper-V errors or malicious
behavior, validate all values that originate from packets that Hyper-V
has sent to the guest. Ensure that invalid values cannot cause indexing
off the end of an array, or subvert an existing validation via integer
overflow. Ensure that outgoing packets do not have any leftover guest
memory that has not been zeroed out.
Reported-by: Juan Vazquez <juvazq@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Link: https://lore.kernel.org/r/20210114202628.119541-1-parri.andrea@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On VF hot remove, NETDEV_GOING_DOWN is sent to notify the VF is about to
go down. At this time, the VF is still sending/receiving traffic and we
request the VSP to switch datapath.
On completion, the datapath is switched to synthetic and we can proceed
with VF hot remove.
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The completion indicates if NVSP_MSG4_TYPE_SWITCH_DATA_PATH has been
processed by the VSP. The traffic is steered to VF or synthetic after we
receive this completion.
Signed-off-by: Long Li <longli@microsoft.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver needs to check if the datapath has been switched to VF before
sending traffic to VF.
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Start to use the lockless version of netdev_notify_peers.
Call the helper where notify variable used to be set true.
Remove the notify bool variable and sort the variables
in reverse Christmas tree order.
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
linux/netdevice.h is included in very many places, touching any
of its dependecies causes large incremental builds.
Drop the linux/ethtool.h include, linux/netdevice.h just needs
a forward declaration of struct ethtool_ops.
Fix all the places which made use of this implicit include.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20201120225052.1427503-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAl+FqrsTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXnN8B/4sRg7j9OTzVBlDiXF2vj6vbuplTIH6
JR6S5f4PNjUg4gV6ghzSnsx1zqNhPSOr78zDqYto8vv+wqqj3thmld8+gAnSbKtt
yoAa7mhbbN1ryJiwPlZzvX4ApzGZPC7byqEi3+zPIcag6TEl8eyYJOmvY3x1zv8x
CsAb57oCC4erD0n4xlTyfuc8TLpO+EiU53PXbR9AovKQHe4m2/8LWyEbmrm5cRUR
gx8RxoLkkrqK0unzcmanbm47QodiaOTUpycs3IvaBeWZQsqSgFZdI1RAdTZNg+U+
GT8eMRXAwpgDpilPm/0n1O0PKGAsVh9Lbw8Btb/ggqnjTUlA4Z3Df23E
=Wy5n
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V updates from Wei Liu:
- a series from Boqun Feng to support page size larger than 4K
- a few miscellaneous clean-ups
* tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
hv: clocksource: Add notrace attribute to read_hv_sched_clock_*() functions
x86/hyperv: Remove aliases with X64 in their name
PCI: hv: Document missing hv_pci_protocol_negotiation() parameter
scsi: storvsc: Support PAGE_SIZE larger than 4K
Driver: hv: util: Use VMBUS_RING_SIZE() for ringbuffer sizes
HID: hyperv: Use VMBUS_RING_SIZE() for ringbuffer sizes
Input: hyperv-keyboard: Use VMBUS_RING_SIZE() for ringbuffer sizes
hv_netvsc: Use HV_HYP_PAGE_SIZE for Hyper-V communication
hv: hyperv.h: Introduce some hvpfn helper functions
Drivers: hv: vmbus: Move virt_to_hvpfn() to hyperv header
Drivers: hv: Use HV_HYP_PAGE in hv_synic_enable_regs()
Drivers: hv: vmbus: Introduce types of GPADL
Drivers: hv: vmbus: Move __vmbus_open()
Drivers: hv: vmbus: Always use HV_HYP_PAGE_SIZE for gpadl
drivers: hv: remove cast from hyperv_die_event
When communicating with Hyper-V, HV_HYP_PAGE_SIZE should be used since
that's the page size used by Hyper-V and Hyper-V expects all
page-related data using the unit of HY_HYP_PAGE_SIZE, for example, the
"pfn" in hv_page_buffer is actually the HV_HYP_PAGE (i.e. the Hyper-V
page) number.
In order to support guest whose page size is not 4k, we need to make
hv_netvsc always use HV_HYP_PAGE_SIZE for Hyper-V communication.
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20200916034817.30282-8-boqun.feng@gmail.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
For additional robustness in the face of Hyper-V errors or malicious
behavior, validate all values that originate from packets that Hyper-V
has sent to the guest in the host-to-guest ring buffer. Ensure that
invalid values cannot cause indexing off the end of an array, or
subvert an existing validation via integer overflow. Ensure that
outgoing packets do not have any leftover guest memory that has not
been zeroed out.
Signed-off-by: Andres Beltran <lkmlabelt@gmail.com>
Co-developed-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous change "hv_netvsc: Switch the data path at the right time
during hibernation" adds the call of netvsc_vf_changed() upon
NETDEV_CHANGE, so it's necessary to avoid the duplicate call and message
when the VF is brought UP or DOWN.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When netvsc_resume() is called, the mlx5 VF NIC has not been resumed yet,
so in the future the host might sliently fail the call netvsc_vf_changed()
-> netvsc_switch_datapath() there, even if the call works now.
Call netvsc_vf_changed() in the NETDEV_CHANGE event handler: at that time
the mlx5 VF NIC has been resumed.
Fixes: 19162fd406 ("hv_netvsc: Fix hibernation for mlx5 VF driver")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5_suspend()/resume() keep the network interface, so during hibernation
netvsc_unregister_vf() and netvsc_register_vf() are not called, and hence
netvsc_resume() should call netvsc_vf_changed() to switch the data path
back to the VF after hibernation. Note: after we close and re-open the
vmbus channel of the netvsc NIC in netvsc_suspend() and netvsc_resume(),
the data path is implicitly switched to the netvsc NIC. Similarly,
netvsc_suspend() should not call netvsc_unregister_vf(), otherwise the VF
can no longer be used after hibernation.
For mlx4, since the VF network interafce is explicitly destroyed and
re-created during hibernation (see mlx4_suspend()/resume()), hv_netvsc
already explicitly switches the data path from and to the VF automatically
via netvsc_register_vf() and netvsc_unregister_vf(), so mlx4 doesn't need
this fix. Note: mlx4 can still work with the fix because in
netvsc_suspend()/resume() ndev_ctx->vf_netdev is NULL for mlx4.
Fixes: 0efeea5fb1 ("hv_netvsc: Add the support of hibernation")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
netvsc_vf_xmit() / dev_queue_xmit() will call VF NIC’s ndo_select_queue
or netdev_pick_tx() again. They will use skb_get_rx_queue() to get the
queue number, so the “skb->queue_mapping - 1” will be used. This may
cause the last queue of VF not been used.
Use skb_record_rx_queue() here, so that the skb_get_rx_queue() called
later will get the correct queue number, and VF will be able to use
all queues.
Fixes: b3bf5666a5 ("hv_netvsc: defer queue selection to VF")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using vf_ops->ndo_select_queue, the number of queues of VF is
usually bigger than the synthetic NIC. This condition may happen
often.
Remove "unlikely" from the comparison of ndev->real_num_tx_queues.
Fixes: b3bf5666a5 ("hv_netvsc: defer queue selection to VF")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the accelerated networking SRIOV VF device has lost carrier
use the synthetic network device which is available as backup
path. This is a rare case since if VF link goes down, normally
the VMBus device will also loose external connectivity as well.
But if the communication is between two VM's on the same host
the VMBus device will still work.
Reported-by: "Shah, Ashish N" <ashish.n.shah@intel.com>
Fixes: 0c195567a8 ("netvsc: transparent VF management")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An imbalanced TX indirection table causes netvsc to have low
performance. This table is created and managed during runtime. To help
better diagnose performance issues caused by imbalanced tables, it needs
make TX indirection tables visible.
Because TX indirection table is driver specified information, so
display it via ethtool register dump.
Signed-off-by: Chi Song <chisong@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlan tagged packets are getting dropped when used with DPDK that uses
the AF_PACKET interface on a hyperV guest.
The packet layer uses the tpacket interface to communicate the vlans
information to the upper layers. On Rx path, these drivers can read the
vlan info from the tpacket header but on the Tx path, this information
is still within the packet frame and requires the paravirtual drivers to
push this back into the NDIS header which is then used by the host OS to
form the packet.
This transition from the packet frame to NDIS header is currently missing
hence causing the host OS to drop the all vlan tagged packets sent by
the drivers that use AF_PACKET (ETH_P_ALL) such as DPDK.
Here is an overview of the changes in the vlan header in the packet path:
The RX path (userspace handles everything):
1. RX VLAN packet is stripped by HOST OS and placed in NDIS header
2. Guest Kernel RX hv_netvsc packets and moves VLAN info from NDIS
header into kernel SKB
3. Kernel shares packets with user space application with PACKET_MMAP.
The SKB VLAN info is copied to tpacket layer and indication set
TP_STATUS_VLAN_VALID.
4. The user space application will re-insert the VLAN info into the frame
The TX path:
1. The user space application has the VLAN info in the frame.
2. Guest kernel gets packets from the application with PACKET_MMAP.
3. The kernel later sends the frame to the hv_netvsc driver. The only way
to send VLANs is when the SKB is setup & the VLAN is stripped from the
frame.
4. TX VLAN is re-inserted by HOST OS based on the NDIS header. If it sees
a VLAN in the frame the packet is dropped.
Cc: xe-linux-external@cisco.com
Cc: Sriram Krishnan <srirakr2@cisco.com>
Signed-off-by: Sriram Krishnan <srirakr2@cisco.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hyperv NIC driver does memory allocation and copy even without XDP.
In XDP mode it will allocate a new page for each packet and copy over
the payload, before invoking the XDP BPF-prog.
The positive thing it that its easy to determine the xdp.frame_sz.
The XDP implementation for hv_netvsc transparently passes xdp_prog
to the associated VF NIC. Many of the Azure VMs are using SRIOV, so
majority of the data are actually processed directly on the VF driver's XDP
path. So the overhead of the synthetic data path (hv_netvsc) is minimal.
Then XDP is enabled on this driver, XDP_PASS and XDP_TX will create the
SKB via build_skb (based on the newly allocated page). Now using XDP
frame_sz this will provide more skb_tailroom, which netstack can use for
SKB coalescing (e.g tcp_try_coalesce -> skb_try_coalesce).
V3: Adjust patch desc to be more positive.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Link: https://lore.kernel.org/bpf/158945339857.97035.10212138582505736163.stgit@firesoul
This patch reverts the folowing commits:
commit 064ff66e2b
"bonding: add missing netdev_update_lockdep_key()"
commit 53d374979e
"net: avoid updating qdisc_xmit_lock_key in netdev_update_lockdep_key()"
commit 1f26c0d3d2
"net: fix kernel-doc warning in <linux/netdevice.h>"
commit ab92d68fc2
"net: core: add generic lockdep keys"
but keeps the addr_list_lock_key because we still lock
addr_list_lock nestedly on stack devices, unlikely xmit_lock
this is safe because we don't take addr_list_lock on any fast
path.
Reported-and-tested-by: syzbot+aaa6fa4949cc5d9b7b25@syzkaller.appspotmail.com
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the ethtool_virtdev_set_link_ksettings function in core/ethtool.c,
ibmveth, netvsc, and virtio now use the core's helper function.
Funtionality changes that pertain to ibmveth driver include:
1. Changed the initial hardcoded link speed to 1GB.
2. Added support for allowing a user to change the reported link
speed via ethtool.
Functionality changes to the netvsc driver include:
1. When netvsc_get_link_ksettings is called, it will defer to the VF
device if it exists to pull accelerated networking values, otherwise
pull default or user-defined values.
2. Similarly, if netvsc_set_link_ksettings called and a VF device
exists, the real values of speed and duplex are changed.
Signed-off-by: Cris Forno <cforno12@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mptcp conflict was overlapping additions.
The SMC conflict was an additional and removal happening at the same
time.
Signed-off-by: David S. Miller <davem@davemloft.net>
When netvsc_attach() is called by operations like changing MTU, etc.,
an extra wakeup may happen while netvsc_attach() calling
rndis_filter_device_add() which sends rndis messages when queue is
stopped in netvsc_detach(). The completion message will wake up queue 0.
We can reproduce the issue by changing MTU etc., then the wake_queue
counter from "ethtool -S" will increase beyond stop_queue counter:
stop_queue: 0
wake_queue: 1
The issue causes queue wake up, and counter increment, no other ill
effects in current code. So we didn't see any network problem for now.
To fix this, initialize tx_disable to true, and set it to false when
the NIC is ready to be attached or registered.
Fixes: 7b2ee50c0c ("hv_netvsc: common detach logic")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper tcp_v6_gso_csum_prep in additional network drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The caller of XDP_SETUP_PROG has already incremented refcnt in
__bpf_prog_get(), so drivers should only increment refcnt by
num_queues - 1.
To fix the issue, update netvsc_xdp_set() to add the correct number
to refcnt.
Hold a refcnt in netvsc_xdp_set()’s other caller, netvsc_attach().
And, do the same in netvsc_vf_setxdp(). Otherwise, every time when VF is
removed and added from the host side, the refcnt will be decreased by one,
which may cause page fault when unloading xdp program.
Fixes: 351e158139 ("hv_netvsc: Add XDP support")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support of XDP in native mode for hv_netvsc driver, and
transparently sets the XDP program on the associated VF NIC as well.
Setting / unsetting XDP program on synthetic NIC (netvsc) propagates to
VF NIC automatically. Setting / unsetting XDP program on VF NIC directly
is not recommended, also not propagated to synthetic NIC, and may be
overwritten by setting of synthetic NIC.
The Azure/Hyper-V synthetic NIC receive buffer doesn't provide headroom
for XDP. We thought about re-use the RNDIS header space, but it's too
small. So we decided to copy the packets to a page buffer for XDP. And,
most of our VMs on Azure have Accelerated Network (SRIOV) enabled, so
most of the packets run on VF NIC. The synthetic NIC is considered as a
fallback data-path. So the data copy on netvsc won't impact performance
significantly.
XDP program cannot run with LRO (RSC) enabled, so you need to disable LRO
before running XDP:
ethtool -K eth0 lro off
XDP actions not yet supported:
XDP_REDIRECT
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
In existing code, the receive indirection table, rx_table, is in
struct rndis_device, which will be reset when changing MTU, ringparam,
etc. User configured receive indirection table values will be lost.
To fix this, move rx_table to struct net_device_context, and check
netif_is_rxfh_configured(), so rx_table will be set to default only
if no user configured value.
Fixes: ff4a441990 ("netvsc: allow get/set of RSS indirection table")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
- Hibernation support (Dexuan Cui).
- Latency testing framework (Branden Bonaby).
- Decoupling Hyper-V page size from guest page size (Himadri Pandya).
-----BEGIN PGP SIGNATURE-----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=oJGE
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V updates from Sasha Levin:
- support for new VMBus protocols (Andrea Parri)
- hibernation support (Dexuan Cui)
- latency testing framework (Branden Bonaby)
- decoupling Hyper-V page size from guest page size (Himadri Pandya)
* tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: (22 commits)
Drivers: hv: vmbus: Fix crash handler reset of Hyper-V synic
drivers/hv: Replace binary semaphore with mutex
drivers: iommu: hyperv: Make HYPERV_IOMMU only available on x86
HID: hyperv: Add the support of hibernation
hv_balloon: Add the support of hibernation
x86/hyperv: Implement hv_is_hibernation_supported()
Drivers: hv: balloon: Remove dependencies on guest page size
Drivers: hv: vmbus: Remove dependencies on guest page size
x86: hv: Add function to allocate zeroed page for Hyper-V
Drivers: hv: util: Specify ring buffer size using Hyper-V page size
Drivers: hv: Specify receive buffer size using Hyper-V page size
tools: hv: add vmbus testing tool
drivers: hv: vmbus: Introduce latency testing
video: hyperv: hyperv_fb: Support deferred IO for Hyper-V frame buffer driver
video: hyperv: hyperv_fb: Obtain screen resolution from Hyper-V host
hv_netvsc: Add the support of hibernation
hv_sock: Add the support of hibernation
video: hyperv_fb: Add the support of hibernation
scsi: storvsc: Add the support of hibernation
Drivers: hv: vmbus: Add module parameter to cap the VMBus version
...
The recording of RSS hash should be controlled by NETIF_F_RXHASH.
Fixes: 1fac7ca4e6 ("hv_netvsc: record hardware hash in skb")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The existing netvsc_detach() and netvsc_attach() APIs make it easy to
implement the suspend/resume callbacks.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Since RSS hash is available from the host, record it in
the skb.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver needs to create a hash value because it
was not done at higher level, then the hash should be marked
as a software not hardware hash.
Fixes: f72860afa2 ("hv_netvsc: Exclude non-TCP port numbers from vRSS hashing")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If rndis_filter_open() fails, we need to remove the rndis device created
in earlier steps, before returning an error code. Otherwise, the retry of
netvsc_attach() from its callers will fail and hang.
Fixes: 7b2ee50c0c ("hv_netvsc: common detach logic")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds