Avoid taking mmu_lock for .invalidate_range_{start,end}() notifications
that are unrelated to KVM. This is possible now that memslot updates are
blocked from range_start() to range_end(); that ensures that lock elision
happens in both or none, and therefore that mmu_notifier_count updates
(which must occur while holding mmu_lock for write) are always paired
across start->end.
Based on patches originally written by Ben Gardon.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We would like to avoid taking mmu_lock for .invalidate_range_{start,end}()
notifications that are unrelated to KVM. Because mmu_notifier_count
must be modified while holding mmu_lock for write, and must always
be paired across start->end to stay balanced, lock elision must
happen in both or none. Therefore, in preparation for this change,
this patch prevents memslot updates across range_start() and range_end().
Note, technically flag-only memslot updates could be allowed in parallel,
but stalling a memslot update for a relatively short amount of time is
not a scalability issue, and this is all more than complex enough.
A long note on the locking: a previous version of the patch used an rwsem
to block the memslot update while the MMU notifier run, but this resulted
in the following deadlock involving the pseudo-lock tagged as
"mmu_notifier_invalidate_range_start".
======================================================
WARNING: possible circular locking dependency detected
5.12.0-rc3+ #6 Tainted: G OE
------------------------------------------------------
qemu-system-x86/3069 is trying to acquire lock:
ffffffff9c775ca0 (mmu_notifier_invalidate_range_start){+.+.}-{0:0}, at: __mmu_notifier_invalidate_range_end+0x5/0x190
but task is already holding lock:
ffffaff7410a9160 (&kvm->mmu_notifier_slots_lock){.+.+}-{3:3}, at: kvm_mmu_notifier_invalidate_range_start+0x36d/0x4f0 [kvm]
which lock already depends on the new lock.
This corresponds to the following MMU notifier logic:
invalidate_range_start
take pseudo lock
down_read() (*)
release pseudo lock
invalidate_range_end
take pseudo lock (**)
up_read()
release pseudo lock
At point (*) we take the mmu_notifiers_slots_lock inside the pseudo lock;
at point (**) we take the pseudo lock inside the mmu_notifiers_slots_lock.
This could cause a deadlock (ignoring for a second that the pseudo lock
is not a lock):
- invalidate_range_start waits on down_read(), because the rwsem is
held by install_new_memslots
- install_new_memslots waits on down_write(), because the rwsem is
held till (another) invalidate_range_end finishes
- invalidate_range_end sits waits on the pseudo lock, held by
invalidate_range_start.
Removing the fairness of the rwsem breaks the cycle (in lockdep terms,
it would change the *shared* rwsem readers into *shared recursive*
readers), so open-code the wait using a readers count and a
spinlock. This also allows handling blockable and non-blockable
critical section in the same way.
Losing the rwsem fairness does theoretically allow MMU notifiers to
block install_new_memslots forever. Note that mm/mmu_notifier.c's own
retry scheme in mmu_interval_read_begin also uses wait/wake_up
and is likewise not fair.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce this safe version of kvm_get_kvm() so that it can be called even
during vm destruction. Use it in kvm_debugfs_open() and remove the verbose
comment. Prepare to be used elsewhere.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20210625153214.43106-3-peterx@redhat.com>
[Preserve the comment in kvm_debugfs_open. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that arm64 has stopped using kvm_is_transparent_hugepage(),
we can remove it, as well as PageTransCompoundMap() which was
only used by the former.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210726153552.1535838-5-maz@kernel.org
The arguments to the KVM_CLEAR_DIRTY_LOG ioctl include a pointer,
therefore it needs a compat ioctl implementation. Otherwise,
32-bit userspace fails to invoke it on 64-bit kernels; for x86
it might work fine by chance if the padding is zero, but not
on big-endian architectures.
Reported-by: Thomas Sattler
Cc: stable@vger.kernel.org
Fixes: 2a31b9db15 ("kvm: introduce manual dirty log reprotect")
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SMT siblings share caches and other hardware, and busy halt polling
will degrade its sibling performance if its sibling is working
Sean Christopherson suggested as below:
"Rather than disallowing halt-polling entirely, on x86 it should be
sufficient to simply have the hardware thread yield to its sibling(s)
via PAUSE. It probably won't get back all performance, but I would
expect it to be close.
This compiles on all KVM architectures, and AFAICT the intended usage
of cpu_relax() is identical for all architectures."
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Message-Id: <20210727111247.55510-1-lirongqing@baidu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* Fixes for host SMIs on AMD
* Fixes for guest SMIs on AMD
* Fixes for selftests on s390 and ARM
* Fix memory leak
* Enforce no-instrumentation area on vmentry when hardware
breakpoints are in use.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmDwRi4UHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroOt4AgAl6xEkMwDC74d/QFIOA7s2GD3ugfa
z5XqGN1qz/nmEMnuIg6/tjTXDPmn/dfLMqy8RGZfyUv6xbgPcv/7JuFMRILvwGTb
SbOVrGnR/QOhMdlfWH34qDkXeEsthTXSgQgVm/iiED0TttvQYVcZ/E9mgzaWQXor
T1yTug2uAUXJ1EBxY0ZBo2kbh+BvvdmhEF0pksZOuwqZdH3zn3QCXwAwkL/OtUYE
M6nNn3j1LU38C4OK1niXOZZVOuMIdk/l7LyFpjUQTFlIqitQAPtBE5MD+K+A9oC2
Yocxyj2tId1e6o8bLic/oN8/LpdORTvA/wDMj5M1DcMzvxQuQIpGYkcVGg==
=gjVA
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
- Allow again loading KVM on 32-bit non-PAE builds
- Fixes for host SMIs on AMD
- Fixes for guest SMIs on AMD
- Fixes for selftests on s390 and ARM
- Fix memory leak
- Enforce no-instrumentation area on vmentry when hardware breakpoints
are in use.
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (25 commits)
KVM: selftests: smm_test: Test SMM enter from L2
KVM: nSVM: Restore nested control upon leaving SMM
KVM: nSVM: Fix L1 state corruption upon return from SMM
KVM: nSVM: Introduce svm_copy_vmrun_state()
KVM: nSVM: Check that VM_HSAVE_PA MSR was set before VMRUN
KVM: nSVM: Check the value written to MSR_VM_HSAVE_PA
KVM: SVM: Fix sev_pin_memory() error checks in SEV migration utilities
KVM: SVM: Return -EFAULT if copy_to_user() for SEV mig packet header fails
KVM: SVM: add module param to control the #SMI interception
KVM: SVM: remove INIT intercept handler
KVM: SVM: #SMI interception must not skip the instruction
KVM: VMX: Remove vmx_msr_index from vmx.h
KVM: X86: Disable hardware breakpoints unconditionally before kvm_x86->run()
KVM: selftests: Address extra memslot parameters in vm_vaddr_alloc
kvm: debugfs: fix memory leak in kvm_create_vm_debugfs
KVM: x86/pmu: Clear anythread deprecated bit when 0xa leaf is unsupported on the SVM
KVM: mmio: Fix use-after-free Read in kvm_vm_ioctl_unregister_coalesced_mmio
KVM: SVM: Revert clearing of C-bit on GPA in #NPF handler
KVM: x86/mmu: Do not apply HPA (memory encryption) mask to GPAs
KVM: x86: Use kernel's x86_phys_bits to handle reduced MAXPHYADDR
...
In commit bc9e9e672d ("KVM: debugfs: Reuse binary stats descriptors")
loop for filling debugfs_stat_data was copy-pasted 2 times, but
in the second loop pointers are saved over pointers allocated
in the first loop. All this causes is a memory leak, fix it.
Fixes: bc9e9e672d ("KVM: debugfs: Reuse binary stats descriptors")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Jing Zhang <jingzhangos@google.com>
Message-Id: <20210701195500.27097-1-paskripkin@gmail.com>
Reviewed-by: Jing Zhang <jingzhangos@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Merge misc updates from Andrew Morton:
"191 patches.
Subsystems affected by this patch series: kthread, ia64, scripts,
ntfs, squashfs, ocfs2, kernel/watchdog, and mm (gup, pagealloc, slab,
slub, kmemleak, dax, debug, pagecache, gup, swap, memcg, pagemap,
mprotect, bootmem, dma, tracing, vmalloc, kasan, initialization,
pagealloc, and memory-failure)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (191 commits)
mm,hwpoison: make get_hwpoison_page() call get_any_page()
mm,hwpoison: send SIGBUS with error virutal address
mm/page_alloc: split pcp->high across all online CPUs for cpuless nodes
mm/page_alloc: allow high-order pages to be stored on the per-cpu lists
mm: replace CONFIG_FLAT_NODE_MEM_MAP with CONFIG_FLATMEM
mm: replace CONFIG_NEED_MULTIPLE_NODES with CONFIG_NUMA
docs: remove description of DISCONTIGMEM
arch, mm: remove stale mentions of DISCONIGMEM
mm: remove CONFIG_DISCONTIGMEM
m68k: remove support for DISCONTIGMEM
arc: remove support for DISCONTIGMEM
arc: update comment about HIGHMEM implementation
alpha: remove DISCONTIGMEM and NUMA
mm/page_alloc: move free_the_page
mm/page_alloc: fix counting of managed_pages
mm/page_alloc: improve memmap_pages dbg msg
mm: drop SECTION_SHIFT in code comments
mm/page_alloc: introduce vm.percpu_pagelist_high_fraction
mm/page_alloc: limit the number of pages on PCP lists when reclaim is active
mm/page_alloc: scale the number of pages that are batch freed
...
vma_lookup() finds the vma of a specific address with a cleaner interface
and is more readable.
Link: https://lkml.kernel.org/r/20210521174745.2219620-11-Liam.Howlett@Oracle.com
Signed-off-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Reviewed-by: Laurent Dufour <ldufour@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Add MTE support in guests, complete with tag save/restore interface
- Reduce the impact of CMOs by moving them in the page-table code
- Allow device block mappings at stage-2
- Reduce the footprint of the vmemmap in protected mode
- Support the vGIC on dumb systems such as the Apple M1
- Add selftest infrastructure to support multiple configuration
and apply that to PMU/non-PMU setups
- Add selftests for the debug architecture
- The usual crop of PMU fixes
PPC:
- Support for the H_RPT_INVALIDATE hypercall
- Conversion of Book3S entry/exit to C
- Bug fixes
S390:
- new HW facilities for guests
- make inline assembly more robust with KASAN and co
x86:
- Allow userspace to handle emulation errors (unknown instructions)
- Lazy allocation of the rmap (host physical -> guest physical address)
- Support for virtualizing TSC scaling on VMX machines
- Optimizations to avoid shattering huge pages at the beginning of live migration
- Support for initializing the PDPTRs without loading them from memory
- Many TLB flushing cleanups
- Refuse to load if two-stage paging is available but NX is not (this has
been a requirement in practice for over a year)
- A large series that separates the MMU mode (WP/SMAP/SMEP etc.) from
CR0/CR4/EFER, using the MMU mode everywhere once it is computed
from the CPU registers
- Use PM notifier to notify the guest about host suspend or hibernate
- Support for passing arguments to Hyper-V hypercalls using XMM registers
- Support for Hyper-V TLB flush hypercalls and enlightened MSR bitmap on
AMD processors
- Hide Hyper-V hypercalls that are not included in the guest CPUID
- Fixes for live migration of virtual machines that use the Hyper-V
"enlightened VMCS" optimization of nested virtualization
- Bugfixes (not many)
Generic:
- Support for retrieving statistics without debugfs
- Cleanups for the KVM selftests API
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmDV9UYUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroOIRgf/XX8fKLh24RnTOs2ldIu2AfRGVrT4
QMrr8MxhmtukBAszk2xKvBt8/6gkUjdaIC3xqEnVjxaDaUvZaEtP7CQlF5JV45rn
iv1zyxUKucXrnIOr+gCioIT7qBlh207zV35ArKioP9Y83cWx9uAs22pfr6g+7RxO
h8bJZlJbSG6IGr3voANCIb9UyjU1V/l8iEHqRwhmr/A5rARPfD7g8lfMEQeGkzX6
+/UydX2fumB3tl8e2iMQj6vLVdSOsCkehvpHK+Z33EpkKhan7GwZ2sZ05WmXV/nY
QLAYfD10KegoNWl5Ay4GTp4hEAIYVrRJCLC+wnLdc0U8udbfCuTC31LK4w==
=NcRh
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"This covers all architectures (except MIPS) so I don't expect any
other feature pull requests this merge window.
ARM:
- Add MTE support in guests, complete with tag save/restore interface
- Reduce the impact of CMOs by moving them in the page-table code
- Allow device block mappings at stage-2
- Reduce the footprint of the vmemmap in protected mode
- Support the vGIC on dumb systems such as the Apple M1
- Add selftest infrastructure to support multiple configuration and
apply that to PMU/non-PMU setups
- Add selftests for the debug architecture
- The usual crop of PMU fixes
PPC:
- Support for the H_RPT_INVALIDATE hypercall
- Conversion of Book3S entry/exit to C
- Bug fixes
S390:
- new HW facilities for guests
- make inline assembly more robust with KASAN and co
x86:
- Allow userspace to handle emulation errors (unknown instructions)
- Lazy allocation of the rmap (host physical -> guest physical
address)
- Support for virtualizing TSC scaling on VMX machines
- Optimizations to avoid shattering huge pages at the beginning of
live migration
- Support for initializing the PDPTRs without loading them from
memory
- Many TLB flushing cleanups
- Refuse to load if two-stage paging is available but NX is not (this
has been a requirement in practice for over a year)
- A large series that separates the MMU mode (WP/SMAP/SMEP etc.) from
CR0/CR4/EFER, using the MMU mode everywhere once it is computed
from the CPU registers
- Use PM notifier to notify the guest about host suspend or hibernate
- Support for passing arguments to Hyper-V hypercalls using XMM
registers
- Support for Hyper-V TLB flush hypercalls and enlightened MSR bitmap
on AMD processors
- Hide Hyper-V hypercalls that are not included in the guest CPUID
- Fixes for live migration of virtual machines that use the Hyper-V
"enlightened VMCS" optimization of nested virtualization
- Bugfixes (not many)
Generic:
- Support for retrieving statistics without debugfs
- Cleanups for the KVM selftests API"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (314 commits)
KVM: x86: rename apic_access_page_done to apic_access_memslot_enabled
kvm: x86: disable the narrow guest module parameter on unload
selftests: kvm: Allows userspace to handle emulation errors.
kvm: x86: Allow userspace to handle emulation errors
KVM: x86/mmu: Let guest use GBPAGES if supported in hardware and TDP is on
KVM: x86/mmu: Get CR4.SMEP from MMU, not vCPU, in shadow page fault
KVM: x86/mmu: Get CR0.WP from MMU, not vCPU, in shadow page fault
KVM: x86/mmu: Drop redundant rsvd bits reset for nested NPT
KVM: x86/mmu: Optimize and clean up so called "last nonleaf level" logic
KVM: x86: Enhance comments for MMU roles and nested transition trickiness
KVM: x86/mmu: WARN on any reserved SPTE value when making a valid SPTE
KVM: x86/mmu: Add helpers to do full reserved SPTE checks w/ generic MMU
KVM: x86/mmu: Use MMU's role to determine PTTYPE
KVM: x86/mmu: Collapse 32-bit PAE and 64-bit statements for helpers
KVM: x86/mmu: Add a helper to calculate root from role_regs
KVM: x86/mmu: Add helper to update paging metadata
KVM: x86/mmu: Don't update nested guest's paging bitmasks if CR0.PG=0
KVM: x86/mmu: Consolidate reset_rsvds_bits_mask() calls
KVM: x86/mmu: Use MMU role_regs to get LA57, and drop vCPU LA57 helper
KVM: x86/mmu: Get nested MMU's root level from the MMU's role
...
- Changes to core scheduling facilities:
- Add "Core Scheduling" via CONFIG_SCHED_CORE=y, which enables
coordinated scheduling across SMT siblings. This is a much
requested feature for cloud computing platforms, to allow
the flexible utilization of SMT siblings, without exposing
untrusted domains to information leaks & side channels, plus
to ensure more deterministic computing performance on SMT
systems used by heterogenous workloads.
There's new prctls to set core scheduling groups, which
allows more flexible management of workloads that can share
siblings.
- Fix task->state access anti-patterns that may result in missed
wakeups and rename it to ->__state in the process to catch new
abuses.
- Load-balancing changes:
- Tweak newidle_balance for fair-sched, to improve
'memcache'-like workloads.
- "Age" (decay) average idle time, to better track & improve workloads
such as 'tbench'.
- Fix & improve energy-aware (EAS) balancing logic & metrics.
- Fix & improve the uclamp metrics.
- Fix task migration (taskset) corner case on !CONFIG_CPUSET.
- Fix RT and deadline utilization tracking across policy changes
- Introduce a "burstable" CFS controller via cgroups, which allows
bursty CPU-bound workloads to borrow a bit against their future
quota to improve overall latencies & batching. Can be tweaked
via /sys/fs/cgroup/cpu/<X>/cpu.cfs_burst_us.
- Rework assymetric topology/capacity detection & handling.
- Scheduler statistics & tooling:
- Disable delayacct by default, but add a sysctl to enable
it at runtime if tooling needs it. Use static keys and
other optimizations to make it more palatable.
- Use sched_clock() in delayacct, instead of ktime_get_ns().
- Misc cleanups and fixes.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=3VDr
-----END PGP SIGNATURE-----
Merge tag 'sched-core-2021-06-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler udpates from Ingo Molnar:
- Changes to core scheduling facilities:
- Add "Core Scheduling" via CONFIG_SCHED_CORE=y, which enables
coordinated scheduling across SMT siblings. This is a much
requested feature for cloud computing platforms, to allow the
flexible utilization of SMT siblings, without exposing untrusted
domains to information leaks & side channels, plus to ensure more
deterministic computing performance on SMT systems used by
heterogenous workloads.
There are new prctls to set core scheduling groups, which allows
more flexible management of workloads that can share siblings.
- Fix task->state access anti-patterns that may result in missed
wakeups and rename it to ->__state in the process to catch new
abuses.
- Load-balancing changes:
- Tweak newidle_balance for fair-sched, to improve 'memcache'-like
workloads.
- "Age" (decay) average idle time, to better track & improve
workloads such as 'tbench'.
- Fix & improve energy-aware (EAS) balancing logic & metrics.
- Fix & improve the uclamp metrics.
- Fix task migration (taskset) corner case on !CONFIG_CPUSET.
- Fix RT and deadline utilization tracking across policy changes
- Introduce a "burstable" CFS controller via cgroups, which allows
bursty CPU-bound workloads to borrow a bit against their future
quota to improve overall latencies & batching. Can be tweaked via
/sys/fs/cgroup/cpu/<X>/cpu.cfs_burst_us.
- Rework assymetric topology/capacity detection & handling.
- Scheduler statistics & tooling:
- Disable delayacct by default, but add a sysctl to enable it at
runtime if tooling needs it. Use static keys and other
optimizations to make it more palatable.
- Use sched_clock() in delayacct, instead of ktime_get_ns().
- Misc cleanups and fixes.
* tag 'sched-core-2021-06-28' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (72 commits)
sched/doc: Update the CPU capacity asymmetry bits
sched/topology: Rework CPU capacity asymmetry detection
sched/core: Introduce SD_ASYM_CPUCAPACITY_FULL sched_domain flag
psi: Fix race between psi_trigger_create/destroy
sched/fair: Introduce the burstable CFS controller
sched/uclamp: Fix uclamp_tg_restrict()
sched/rt: Fix Deadline utilization tracking during policy change
sched/rt: Fix RT utilization tracking during policy change
sched: Change task_struct::state
sched,arch: Remove unused TASK_STATE offsets
sched,timer: Use __set_current_state()
sched: Add get_current_state()
sched,perf,kvm: Fix preemption condition
sched: Introduce task_is_running()
sched: Unbreak wakeups
sched/fair: Age the average idle time
sched/cpufreq: Consider reduced CPU capacity in energy calculation
sched/fair: Take thermal pressure into account while estimating energy
thermal/cpufreq_cooling: Update offline CPUs per-cpu thermal_pressure
sched/fair: Return early from update_tg_cfs_load() if delta == 0
...
To remove code duplication, use the binary stats descriptors in the
implementation of the debugfs interface for statistics. This unifies
the definition of statistics for the binary and debugfs interfaces.
Signed-off-by: Jing Zhang <jingzhangos@google.com>
Message-Id: <20210618222709.1858088-8-jingzhangos@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a VCPU ioctl to get a statistics file descriptor by which a read
functionality is provided for userspace to read out VCPU stats header,
descriptors and data.
Define VCPU statistics descriptors and header for all architectures.
Reviewed-by: David Matlack <dmatlack@google.com>
Reviewed-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Fuad Tabba <tabba@google.com>
Tested-by: Fuad Tabba <tabba@google.com> #arm64
Signed-off-by: Jing Zhang <jingzhangos@google.com>
Message-Id: <20210618222709.1858088-5-jingzhangos@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a VM ioctl to get a statistics file descriptor by which a read
functionality is provided for userspace to read out VM stats header,
descriptors and data.
Define VM statistics descriptors and header for all architectures.
Reviewed-by: David Matlack <dmatlack@google.com>
Reviewed-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Fuad Tabba <tabba@google.com>
Tested-by: Fuad Tabba <tabba@google.com> #arm64
Signed-off-by: Jing Zhang <jingzhangos@google.com>
Message-Id: <20210618222709.1858088-4-jingzhangos@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's possible to create a region which maps valid but non-refcounted
pages (e.g., tail pages of non-compound higher order allocations). These
host pages can then be returned by gfn_to_page, gfn_to_pfn, etc., family
of APIs, which take a reference to the page, which takes it from 0 to 1.
When the reference is dropped, this will free the page incorrectly.
Fix this by only taking a reference on valid pages if it was non-zero,
which indicates it is participating in normal refcounting (and can be
released with put_page).
This addresses CVE-2021-22543.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Tested-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This commit defines the API for userspace and prepare the common
functionalities to support per VM/VCPU binary stats data readings.
The KVM stats now is only accessible by debugfs, which has some
shortcomings this change series are supposed to fix:
1. The current debugfs stats solution in KVM could be disabled
when kernel Lockdown mode is enabled, which is a potential
rick for production.
2. The current debugfs stats solution in KVM is organized as "one
stats per file", it is good for debugging, but not efficient
for production.
3. The stats read/clear in current debugfs solution in KVM are
protected by the global kvm_lock.
Besides that, there are some other benefits with this change:
1. All KVM VM/VCPU stats can be read out in a bulk by one copy
to userspace.
2. A schema is used to describe KVM statistics. From userspace's
perspective, the KVM statistics are self-describing.
3. With the fd-based solution, a separate telemetry would be able
to read KVM stats in a less privileged environment.
4. After the initial setup by reading in stats descriptors, a
telemetry only needs to read the stats data itself, no more
parsing or setup is needed.
Reviewed-by: David Matlack <dmatlack@google.com>
Reviewed-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Fuad Tabba <tabba@google.com>
Tested-by: Fuad Tabba <tabba@google.com> #arm64
Signed-off-by: Jing Zhang <jingzhangos@google.com>
Message-Id: <20210618222709.1858088-3-jingzhangos@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Generic KVM stats are those collected in architecture independent code
or those supported by all architectures; put all generic statistics in
a separate structure. This ensures that they are defined the same way
in the statistics API which is being added, removing duplication among
different architectures in the declaration of the descriptors.
No functional change intended.
Reviewed-by: David Matlack <dmatlack@google.com>
Reviewed-by: Ricardo Koller <ricarkol@google.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Jing Zhang <jingzhangos@google.com>
Message-Id: <20210618222709.1858088-2-jingzhangos@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When ran from the sched-out path (preempt_notifier or perf_event),
p->state is irrelevant to determine preemption. You can get preempted
with !task_is_running() just fine.
The right indicator for preemption is if the task is still on the
runqueue in the sched-out path.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20210611082838.285099381@infradead.org
Add KVM PM-notifier so that architectures can have arch-specific
VM suspend/resume routines. Such architectures need to select
CONFIG_HAVE_KVM_PM_NOTIFIER and implement kvm_arch_pm_notifier().
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Message-Id: <20210606021045.14159-1-senozhatsky@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a new lock to protect the arch-specific fields of memslots if they
need to be modified in a kvm->srcu read critical section. A future
commit will use this lock to lazily allocate memslot rmaps for x86.
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20210518173414.450044-5-bgardon@google.com>
[Add Documentation/ hunk. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Factor out copying kvm_memslots from allocating the memory for new ones
in preparation for adding a new lock to protect the arch-specific fields
of the memslots.
No functional change intended.
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20210518173414.450044-4-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For VMX, when a vcpu enters HLT emulation, pi_post_block will:
1) Add vcpu to per-cpu list of blocked vcpus.
2) Program the posted-interrupt descriptor "notification vector"
to POSTED_INTR_WAKEUP_VECTOR
With interrupt remapping, an interrupt will set the PIR bit for the
vector programmed for the device on the CPU, test-and-set the
ON bit on the posted interrupt descriptor, and if the ON bit is clear
generate an interrupt for the notification vector.
This way, the target CPU wakes upon a device interrupt and wakes up
the target vcpu.
Problem is that pi_post_block only programs the notification vector
if kvm_arch_has_assigned_device() is true. Its possible for the
following to happen:
1) vcpu V HLTs on pcpu P, kvm_arch_has_assigned_device is false,
notification vector is not programmed
2) device is assigned to VM
3) device interrupts vcpu V, sets ON bit
(notification vector not programmed, so pcpu P remains in idle)
4) vcpu 0 IPIs vcpu V (in guest), but since pi descriptor ON bit is set,
kvm_vcpu_kick is skipped
5) vcpu 0 busy spins on vcpu V's response for several seconds, until
RCU watchdog NMIs all vCPUs.
To fix this, use the start_assignment kvm_x86_ops callback to kick
vcpus out of the halt loop, so the notification vector is
properly reprogrammed to the wakeup vector.
Reported-by: Pei Zhang <pezhang@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Message-Id: <20210526172014.GA29007@fuller.cnet>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM_REQ_UNBLOCK will be used to exit a vcpu from
its inner vcpu halt emulation loop.
Rename KVM_REQ_PENDING_TIMER to KVM_REQ_UNBLOCK, switch
PowerPC to arch specific request bit.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Message-Id: <20210525134321.303768132@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is inspired by commit 262de4102c (kvm: exit halt polling on
need_resched() as well). Due to PPC implements an arch specific halt
polling logic, we have to the need_resched() check there as well. This
patch adds a helper function that can be shared between book3s and generic
halt-polling loops.
Reviewed-by: David Matlack <dmatlack@google.com>
Reviewed-by: Venkatesh Srinivas <venkateshs@chromium.org>
Cc: Ben Segall <bsegall@google.com>
Cc: Venkatesh Srinivas <venkateshs@chromium.org>
Cc: Jim Mattson <jmattson@google.com>
Cc: David Matlack <dmatlack@google.com>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1621339235-11131-1-git-send-email-wanpengli@tencent.com>
[Make the function inline. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Fix regression with irqbypass not restarting the guest on failed connect
- Fix regression with debug register decoding resulting in overlapping access
- Commit exception state on exit to usrspace
- Fix the MMU notifier return values
- Add missing 'static' qualifiers in the new host stage-2 code
-----BEGIN PGP SIGNATURE-----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=57tg
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 5.13, take #1
- Fix regression with irqbypass not restarting the guest on failed connect
- Fix regression with debug register decoding resulting in overlapping access
- Commit exception state on exit to usrspace
- Fix the MMU notifier return values
- Add missing 'static' qualifiers in the new host stage-2 code
This reverts commit a979a6aa00.
The reverted commit may cause VM freeze on arm64 with GICv4,
where stopping a consumer is implemented by suspending the VM.
Should the connect fail, the VM will not be resumed, which
is a bit of a problem.
It also erroneously calls the producer destructor unconditionally,
which is unexpected.
Reported-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Suggested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
[maz: tags and cc-stable, commit message update]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Fixes: a979a6aa00 ("irqbypass: do not start cons/prod when failed connect")
Link: https://lore.kernel.org/r/3a2c66d6-6ca0-8478-d24b-61e8e3241b20@hisilicon.com
Link: https://lore.kernel.org/r/20210508071152.722425-1-lingshan.zhu@intel.com
Cc: stable@vger.kernel.org
When growing halt-polling, there is no check that the poll time exceeds
the per-VM limit. It's possible for vcpu->halt_poll_ns to grow past
kvm->max_halt_poll_ns and stay there until a halt which takes longer
than kvm->halt_poll_ns.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Venkatesh Srinivas <venkateshs@chromium.org>
Message-Id: <20210506152442.4010298-1-venkateshs@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
single_task_running() is usually more general than need_resched()
but CFS_BANDWIDTH throttling will use resched_task() when there
is just one task to get the task to block. This was causing
long-need_resched warnings and was likely allowing VMs to
overrun their quota when halt polling.
Signed-off-by: Ben Segall <bsegall@google.com>
Signed-off-by: Venkatesh Srinivas <venkateshs@chromium.org>
Message-Id: <20210429162233.116849-1-venkateshs@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Jim Mattson <jmattson@google.com>
Both lock holder vCPU and IPI receiver that has halted are condidate for
boost. However, the PLE handler was originally designed to deal with the
lock holder preemption problem. The Intel PLE occurs when the spinlock
waiter is in kernel mode. This assumption doesn't hold for IPI receiver,
they can be in either kernel or user mode. the vCPU candidate in user mode
will not be boosted even if they should respond to IPIs. Some benchmarks
like pbzip2, swaptions etc do the TLB shootdown in kernel mode and most
of the time they are running in user mode. It can lead to a large number
of continuous PLE events because the IPI sender causes PLE events
repeatedly until the receiver is scheduled while the receiver is not
candidate for a boost.
This patch boosts the vCPU candidiate in user mode which is delivery
interrupt. We can observe the speed of pbzip2 improves 10% in 96 vCPUs
VM in over-subscribe scenario (The host machine is 2 socket, 48 cores,
96 HTs Intel CLX box). There is no performance regression for other
benchmarks like Unixbench spawn (most of the time contend read/write
lock in kernel mode), ebizzy (most of the time contend read/write sem
and TLB shoodtdown in kernel mode).
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1618542490-14756-1-git-send-email-wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a capability for userspace to mirror SEV encryption context from
one vm to another. On our side, this is intended to support a
Migration Helper vCPU, but it can also be used generically to support
other in-guest workloads scheduled by the host. The intention is for
the primary guest and the mirror to have nearly identical memslots.
The primary benefits of this are that:
1) The VMs do not share KVM contexts (think APIC/MSRs/etc), so they
can't accidentally clobber each other.
2) The VMs can have different memory-views, which is necessary for post-copy
migration (the migration vCPUs on the target need to read and write to
pages, when the primary guest would VMEXIT).
This does not change the threat model for AMD SEV. Any memory involved
is still owned by the primary guest and its initial state is still
attested to through the normal SEV_LAUNCH_* flows. If userspace wanted
to circumvent SEV, they could achieve the same effect by simply attaching
a vCPU to the primary VM.
This patch deliberately leaves userspace in charge of the memslots for the
mirror, as it already has the power to mess with them in the primary guest.
This patch does not support SEV-ES (much less SNP), as it does not
handle handing off attested VMSAs to the mirror.
For additional context, we need a Migration Helper because SEV PSP
migration is far too slow for our live migration on its own. Using
an in-guest migrator lets us speed this up significantly.
Signed-off-by: Nathan Tempelman <natet@google.com>
Message-Id: <20210408223214.2582277-1-natet@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert a comment above kvm_io_bus_unregister_dev() into an actual
lockdep assertion, and opportunistically add curly braces to a multi-line
for-loop.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210412222050.876100-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Abort the walk of coalesced MMIO zones if kvm_io_bus_unregister_dev()
fails to allocate memory for the new instance of the bus. If it can't
instantiate a new bus, unregister_dev() destroys all devices _except_ the
target device. But, it doesn't tell the caller that it obliterated the
bus and invoked the destructor for all devices that were on the bus. In
the coalesced MMIO case, this can result in a deleted list entry
dereference due to attempting to continue iterating on coalesced_zones
after future entries (in the walk) have been deleted.
Opportunistically add curly braces to the for-loop, which encompasses
many lines but sneaks by without braces due to the guts being a single
if statement.
Fixes: f65886606c ("KVM: fix memory leak in kvm_io_bus_unregister_dev()")
Cc: stable@vger.kernel.org
Reported-by: Hao Sun <sunhao.th@gmail.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210412222050.876100-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If allocating a new instance of an I/O bus fails when unregistering a
device, wait to destroy the device until after all readers are guaranteed
to see the new null bus. Destroying devices before the bus is nullified
could lead to use-after-free since readers expect the devices on their
reference of the bus to remain valid.
Fixes: f65886606c ("KVM: fix memory leak in kvm_io_bus_unregister_dev()")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210412222050.876100-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Defer acquiring mmu_lock in the MMU notifier paths until a "hit" has been
detected in the memslots, i.e. don't take the lock for notifications that
don't affect the guest.
For small VMs, spurious locking is a minor annoyance. And for "volatile"
setups where the majority of notifications _are_ relevant, this barely
qualifies as an optimization.
But, for large VMs (hundreds of threads) with static setups, e.g. no
page migration, no swapping, etc..., the vast majority of MMU notifier
callbacks will be unrelated to the guest, e.g. will often be in response
to the userspace VMM adjusting its own virtual address space. In such
large VMs, acquiring mmu_lock can be painful as it blocks vCPUs from
handling page faults. In some scenarios it can even be "fatal" in the
sense that it causes unacceptable brownouts, e.g. when rebuilding huge
pages after live migration, a significant percentage of vCPUs will be
attempting to handle page faults.
x86's TDP MMU implementation is especially susceptible to spurious
locking due it taking mmu_lock for read when handling page faults.
Because rwlock is fair, a single writer will stall future readers, while
the writer is itself stalled waiting for in-progress readers to complete.
This is exacerbated by the MMU notifiers often firing multiple times in
quick succession, e.g. moving a page will (always?) invoke three separate
notifiers: .invalidate_range_start(), invalidate_range_end(), and
.change_pte(). Unnecessarily taking mmu_lock each time means even a
single spurious sequence can be problematic.
Note, this optimizes only the unpaired callbacks. Optimizing the
.invalidate_range_{start,end}() pairs is more complex and will be done in
a future patch.
Suggested-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210402005658.3024832-9-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acquire and release mmu_lock in the __kvm_handle_hva_range() helper
instead of requiring the caller to do the same. This paves the way for
future patches to take mmu_lock if and only if an overlapping memslot is
found, without also having to introduce the on_lock() shenanigans used
to manipulate the notifier count and sequence.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210402005658.3024832-8-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Yank out the hva-based MMU notifier APIs now that all architectures that
use the notifiers have moved to the gfn-based APIs.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210402005658.3024832-7-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the hva->gfn lookup for MMU notifiers into common code. Every arch
does a similar lookup, and some arch code is all but identical across
multiple architectures.
In addition to consolidating code, this will allow introducing
optimizations that will benefit all architectures without incurring
multiple walks of the memslots, e.g. by taking mmu_lock if and only if a
relevant range exists in the memslots.
The use of __always_inline to avoid indirect call retpolines, as done by
x86, may also benefit other architectures.
Consolidating the lookups also fixes a wart in x86, where the legacy MMU
and TDP MMU each do their own memslot walks.
Lastly, future enhancements to the memslot implementation, e.g. to add an
interval tree to track host address, will need to touch far less arch
specific code.
MIPS, PPC, and arm64 will be converted one at a time in future patches.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210402005658.3024832-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In KVM's .change_pte() notification callback, replace the notifier
sequence bump with a WARN_ON assertion that the notifier count is
elevated. An elevated count provides stricter protections than bumping
the sequence, and the sequence is guarnateed to be bumped before the
count hits zero.
When .change_pte() was added by commit 828502d300 ("ksm: add
mmu_notifier set_pte_at_notify()"), bumping the sequence was necessary
as .change_pte() would be invoked without any surrounding notifications.
However, since commit 6bdb913f0a ("mm: wrap calls to set_pte_at_notify
with invalidate_range_start and invalidate_range_end"), all calls to
.change_pte() are guaranteed to be surrounded by start() and end(), and
so are guaranteed to run with an elevated notifier count.
Note, wrapping .change_pte() with .invalidate_range_{start,end}() is a
bug of sorts, as invalidating the secondary MMU's (KVM's) PTE defeats
the purpose of .change_pte(). Every arch's kvm_set_spte_hva() assumes
.change_pte() is called when the relevant SPTE is present in KVM's MMU,
as the original goal was to accelerate Kernel Samepage Merging (KSM) by
updating KVM's SPTEs without requiring a VM-Exit (due to invalidating
the SPTE). I.e. it means that .change_pte() is effectively dead code
on _all_ architectures.
x86 and MIPS are clearcut nops if the old SPTE is not-present, and that
is guaranteed due to the prior invalidation. PPC simply unmaps the SPTE,
which again should be a nop due to the invalidation. arm64 is a bit
murky, but it's also likely a nop because kvm_pgtable_stage2_map() is
called without a cache pointer, which means it will map an entry if and
only if an existing PTE was found.
For now, take advantage of the bug to simplify future consolidation of
KVMs's MMU notifier code. Doing so will not greatly complicate fixing
.change_pte(), assuming it's even worth fixing. .change_pte() has been
broken for 8+ years and no one has complained. Even if there are
KSM+KVM users that care deeply about its performance, the benefits of
avoiding VM-Exits via .change_pte() need to be reevaluated to justify
the added complexity and testing burden. Ripping out .change_pte()
entirely would be a lot easier.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use GFP_KERNEL_ACCOUNT when allocating vCPUs to make it more obvious that
that the allocations are accounted, to make it easier to audit KVM's
allocations in the future, and to be consistent with other cache usage in
KVM.
When using SLAB/SLUB, this is a nop as the cache itself is created with
SLAB_ACCOUNT.
When using SLOB, there are caveats within caveats. SLOB doesn't honor
SLAB_ACCOUNT, so passing GFP_KERNEL_ACCOUNT will result in vCPU
allocations now being accounted. But, even that depends on internal
SLOB details as SLOB will only go to the page allocator when its cache is
depleted. That just happens to be extremely likely for vCPUs because the
size of kvm_vcpu is larger than the a page for almost all combinations of
architecture and page size. Whether or not the SLOB behavior is by
design is unknown; it's just as likely that no SLOB users care about
accounding and so no one has bothered to implemented support in SLOB.
Regardless, accounting vCPU allocations will not break SLOB+KVM+cgroup
users, if any exist.
Reviewed-by: Wanpeng Li <kernellwp@gmail.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210406190740.4055679-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move arm64's MMU notifier trace events into common code in preparation
for doing the hva->gfn lookup in common code. The alternative would be
to trace the gfn instead of hva, but that's not obviously better and
could also be done in common code. Tracing the notifiers is also quite
handy for debug regardless of architecture.
Remove a completely redundant tracepoint from PPC e500.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210326021957.1424875-10-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Track the range being invalidated by mmu_notifier and skip page fault
retries if the fault address is not affected by the in-progress
invalidation. Handle concurrent invalidations by finding the minimal
range which includes all ranges being invalidated. Although the combined
range may include unrelated addresses and cannot be shrunk as individual
invalidation operations complete, it is unlikely the marginal gains of
proper range tracking are worth the additional complexity.
The primary benefit of this change is the reduction in the likelihood of
extreme latency when handing a page fault due to another thread having
been preempted while modifying host virtual addresses.
Signed-off-by: David Stevens <stevensd@chromium.org>
Message-Id: <20210222024522.1751719-3-stevensd@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use kvm_pfn_t, a.k.a. u64, for the local 'pfn' variable when retrieving
a so called "remapped" hva/pfn pair. In theory, the hva could resolve to
a pfn in high memory on a 32-bit kernel.
This bug was inadvertantly exposed by commit bd2fae8da7 ("KVM: do not
assume PTE is writable after follow_pfn"), which added an error PFN value
to the mix, causing gcc to comlain about overflowing the unsigned long.
arch/x86/kvm/../../../virt/kvm/kvm_main.c: In function ‘hva_to_pfn_remapped’:
include/linux/kvm_host.h:89:30: error: conversion from ‘long long unsigned int’
to ‘long unsigned int’ changes value from
‘9218868437227405314’ to ‘2’ [-Werror=overflow]
89 | #define KVM_PFN_ERR_RO_FAULT (KVM_PFN_ERR_MASK + 2)
| ^
virt/kvm/kvm_main.c:1935:9: note: in expansion of macro ‘KVM_PFN_ERR_RO_FAULT’
Cc: stable@vger.kernel.org
Fixes: add6a0cd1c ("KVM: MMU: try to fix up page faults before giving up")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210208201940.1258328-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, the follow_pfn function is exported for modules but
follow_pte is not. However, follow_pfn is very easy to misuse,
because it does not provide protections (so most of its callers
assume the page is writable!) and because it returns after having
already unlocked the page table lock.
Provide instead a simplified version of follow_pte that does
not have the pmdpp and range arguments. The older version
survives as follow_invalidate_pte() for use by fs/dax.c.
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a read / write lock to be used in place of the MMU spinlock on x86.
The rwlock will enable the TDP MMU to handle page faults, and other
operations in parallel in future commits.
Reviewed-by: Peter Feiner <pfeiner@google.com>
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20210202185734.1680553-19-bgardon@google.com>
[Introduce virt/kvm/mmu_lock.h - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
fixed the following warning：
/virt/kvm/dirty_ring.c:70:20-27: WARNING: vzalloc should be used for
ring -> dirty_gfns, instead of vmalloc/memset.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Message-Id: <1611547045-13669-1-git-send-email-tiantao6@hisilicon.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to convert an HVA to a PFN, KVM usually tries to use
the get_user_pages family of functinso. This however is not
possible for VM_IO vmas; in that case, KVM instead uses follow_pfn.
In doing this however KVM loses the information on whether the
PFN is writable. That is usually not a problem because the main
use of VM_IO vmas with KVM is for BARs in PCI device assignment,
however it is a bug. To fix it, use follow_pte and check pte_write
while under the protection of the PTE lock. The information can
be used to fail hva_to_pfn_remapped or passed back to the
caller via *writable.
Usage of follow_pfn was introduced in commit add6a0cd1c ("KVM: MMU: try to fix
up page faults before giving up", 2016-07-05); however, even older version
have the same issue, all the way back to commit 2e2e3738af ("KVM:
Handle vma regions with no backing page", 2008-07-20), as they also did
not check whether the PFN was writable.
Fixes: 2e2e3738af ("KVM: Handle vma regions with no backing page")
Reported-by: David Stevens <stevensd@google.com>
Cc: 3pvd@google.com
Cc: Jann Horn <jannh@google.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Don't allow tagged pointers to point to memslots
- Filter out ARMv8.1+ PMU events on v8.0 hardware
- Hide PMU registers from userspace when no PMU is configured
- More PMU cleanups
- Don't try to handle broken PSCI firmware
- More sys_reg() to reg_to_encoding() conversions
-----BEGIN PGP SIGNATURE-----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=GHVB
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 5.11, take #2
- Don't allow tagged pointers to point to memslots
- Filter out ARMv8.1+ PMU events on v8.0 hardware
- Hide PMU registers from userspace when no PMU is configured
- More PMU cleanups
- Don't try to handle broken PSCI firmware
- More sys_reg() to reg_to_encoding() conversions
The use of a tagged address could be pretty confusing for the
whole memslot infrastructure as well as the MMU notifiers.
Forbid it altogether, as it never quite worked the first place.
Cc: stable@vger.kernel.org
Reported-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
* Fixes for the new scalable MMU
* Fixes for migration of nested hypervisors on AMD
* Fix for clang integrated assembler
* Fix for left shift by 64 (UBSAN)
* Small cleanups
* Straggler SEV-ES patch
ARM:
* VM init cleanups
* PSCI relay cleanups
* Kill CONFIG_KVM_ARM_PMU
* Fixup __init annotations
* Fixup reg_to_encoding()
* Fix spurious PMCR_EL0 access
* selftests cleanups
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl/4YOMUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMg0Qf/eGDOoLL18KhA9MpoPXusR5kU+82G
AcbFj9siNW46EF7mL+sw/xAx+gZaqSpIEmn/f6BzgiaUBdFTv9CKX3B54e43e59G
HAKD0NpqwvDIi1b0T6bcgC92mY3Qx/IDCc7/9JYjBs/iORfqyWW6xVtkF/Gfymxt
eK+MnfMqqNZODgR/cZnCH1E48fuwOvRMxLqilLi3OOMSUfs2cQOSLTNfYQYqjeaJ
dsQ4YeyPJO5JHtfHFr6VPIo/jDhowniac9CNvOomWWVIx2zPYVSl9d8ub6ESEPNF
GM7UeBCOMmZG/a3qFEZPAUJ7znW4yYE85Z6pjxlrGhd1I54MJi4dd+RApw==
=5Nfj
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"x86:
- Fixes for the new scalable MMU
- Fixes for migration of nested hypervisors on AMD
- Fix for clang integrated assembler
- Fix for left shift by 64 (UBSAN)
- Small cleanups
- Straggler SEV-ES patch
ARM:
- VM init cleanups
- PSCI relay cleanups
- Kill CONFIG_KVM_ARM_PMU
- Fixup __init annotations
- Fixup reg_to_encoding()
- Fix spurious PMCR_EL0 access
Misc:
- selftests cleanups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (38 commits)
KVM: x86: __kvm_vcpu_halt can be static
KVM: SVM: Add support for booting APs in an SEV-ES guest
KVM: nSVM: cancel KVM_REQ_GET_NESTED_STATE_PAGES on nested vmexit
KVM: nSVM: mark vmcb as dirty when forcingly leaving the guest mode
KVM: nSVM: correctly restore nested_run_pending on migration
KVM: x86/mmu: Clarify TDP MMU page list invariants
KVM: x86/mmu: Ensure TDP MMU roots are freed after yield
kvm: check tlbs_dirty directly
KVM: x86: change in pv_eoi_get_pending() to make code more readable
MAINTAINERS: Really update email address for Sean Christopherson
KVM: x86: fix shift out of bounds reported by UBSAN
KVM: selftests: Implement perf_test_util more conventionally
KVM: selftests: Use vm_create_with_vcpus in create_vm
KVM: selftests: Factor out guest mode code
KVM/SVM: Remove leftover __svm_vcpu_run prototype from svm.c
KVM: SVM: Add register operand to vmsave call in sev_es_vcpu_load
KVM: x86/mmu: Optimize not-present/MMIO SPTE check in get_mmio_spte()
KVM: x86/mmu: Use raw level to index into MMIO walks' sptes array
KVM: x86/mmu: Get root level from walkers when retrieving MMIO SPTE
KVM: x86/mmu: Use -1 to flag an undefined spte in get_mmio_spte()
...
In kvm_mmu_notifier_invalidate_range_start(), tlbs_dirty is used as:
need_tlb_flush |= kvm->tlbs_dirty;
with need_tlb_flush's type being int and tlbs_dirty's type being long.
It means that tlbs_dirty is always used as int and the higher 32 bits
is useless. We need to check tlbs_dirty in a correct way and this
change checks it directly without propagating it to need_tlb_flush.
Note: it's _extremely_ unlikely this neglecting of higher 32 bits can
cause problems in practice. It would require encountering tlbs_dirty
on a 4 billion count boundary, and KVM would need to be using shadow
paging or be running a nested guest.
Cc: stable@vger.kernel.org
Fixes: a4ee1ca4a3 ("KVM: MMU: delay flush all tlbs on sync_page path")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Message-Id: <20201217154118.16497-1-jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* PSCI relay at EL2 when "protected KVM" is enabled
* New exception injection code
* Simplification of AArch32 system register handling
* Fix PMU accesses when no PMU is enabled
* Expose CSV3 on non-Meltdown hosts
* Cache hierarchy discovery fixes
* PV steal-time cleanups
* Allow function pointers at EL2
* Various host EL2 entry cleanups
* Simplification of the EL2 vector allocation
s390:
* memcg accouting for s390 specific parts of kvm and gmap
* selftest for diag318
* new kvm_stat for when async_pf falls back to sync
x86:
* Tracepoints for the new pagetable code from 5.10
* Catch VFIO and KVM irqfd events before userspace
* Reporting dirty pages to userspace with a ring buffer
* SEV-ES host support
* Nested VMX support for wait-for-SIPI activity state
* New feature flag (AVX512 FP16)
* New system ioctl to report Hyper-V-compatible paravirtualization features
Generic:
* Selftest improvements
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl/bdL4UHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNgQQgAnTH6rhXa++Zd5F0EM2NwXwz3iEGb
lOq1DZSGjs6Eekjn8AnrWbmVQr+CBCuGU9MrxpSSzNDK/awryo3NwepOWAZw9eqk
BBCVwGBbJQx5YrdgkGC0pDq2sNzcpW/VVB3vFsmOxd9eHblnuKSIxEsCCXTtyqIt
XrLpQ1UhvI4yu102fDNhuFw2EfpzXm+K0Lc0x6idSkdM/p7SyeOxiv8hD4aMr6+G
bGUQuMl4edKZFOWFigzr8NovQAvDHZGrwfihu2cLRYKLhV97QuWVmafv/yYfXcz2
drr+wQCDNzDOXyANnssmviazrhOX0QmTAhbIXGGX/kTxYKcfPi83ZLoI3A==
=ISud
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"Much x86 work was pushed out to 5.12, but ARM more than made up for it.
ARM:
- PSCI relay at EL2 when "protected KVM" is enabled
- New exception injection code
- Simplification of AArch32 system register handling
- Fix PMU accesses when no PMU is enabled
- Expose CSV3 on non-Meltdown hosts
- Cache hierarchy discovery fixes
- PV steal-time cleanups
- Allow function pointers at EL2
- Various host EL2 entry cleanups
- Simplification of the EL2 vector allocation
s390:
- memcg accouting for s390 specific parts of kvm and gmap
- selftest for diag318
- new kvm_stat for when async_pf falls back to sync
x86:
- Tracepoints for the new pagetable code from 5.10
- Catch VFIO and KVM irqfd events before userspace
- Reporting dirty pages to userspace with a ring buffer
- SEV-ES host support
- Nested VMX support for wait-for-SIPI activity state
- New feature flag (AVX512 FP16)
- New system ioctl to report Hyper-V-compatible paravirtualization features
Generic:
- Selftest improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (171 commits)
KVM: SVM: fix 32-bit compilation
KVM: SVM: Add AP_JUMP_TABLE support in prep for AP booting
KVM: SVM: Provide support to launch and run an SEV-ES guest
KVM: SVM: Provide an updated VMRUN invocation for SEV-ES guests
KVM: SVM: Provide support for SEV-ES vCPU loading
KVM: SVM: Provide support for SEV-ES vCPU creation/loading
KVM: SVM: Update ASID allocation to support SEV-ES guests
KVM: SVM: Set the encryption mask for the SVM host save area
KVM: SVM: Add NMI support for an SEV-ES guest
KVM: SVM: Guest FPU state save/restore not needed for SEV-ES guest
KVM: SVM: Do not report support for SMM for an SEV-ES guest
KVM: x86: Update __get_sregs() / __set_sregs() to support SEV-ES
KVM: SVM: Add support for CR8 write traps for an SEV-ES guest
KVM: SVM: Add support for CR4 write traps for an SEV-ES guest
KVM: SVM: Add support for CR0 write traps for an SEV-ES guest
KVM: SVM: Add support for EFER write traps for an SEV-ES guest
KVM: SVM: Support string IO operations for an SEV-ES guest
KVM: SVM: Support MMIO for an SEV-ES guest
KVM: SVM: Create trace events for VMGEXIT MSR protocol processing
KVM: SVM: Create trace events for VMGEXIT processing
...
A VCPU of a VM can allocate couple of pages which can be mmap'ed by the
user space application. At the moment this memory is not charged to the
memcg of the VMM. On a large machine running large number of VMs or
small number of VMs having large number of VCPUs, this unaccounted
memory can be very significant. So, charge this memory to the memcg of
the VMM. Please note that lifetime of these allocations corresponds to
the lifetime of the VMM.
Link: https://lkml.kernel.org/r/20201106202923.2087414-1-shakeelb@google.com
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Roman Gushchin <guro@fb.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because kvm dirty rings and kvm dirty log is used in an exclusive way,
Let's avoid creating the dirty_bitmap when kvm dirty ring is enabled.
At the meantime, since the dirty_bitmap will be conditionally created
now, we can't use it as a sign of "whether this memory slot enabled
dirty tracking". Change users like that to check against the kvm
memory slot flags.
Note that there still can be chances where the kvm memory slot got its
dirty_bitmap allocated, _if_ the memory slots are created before
enabling of the dirty rings and at the same time with the dirty
tracking capability enabled, they'll still with the dirty_bitmap.
However it should not hurt much (e.g., the bitmaps will always be
freed if they are there), and the real users normally won't trigger
this because dirty bit tracking flag should in most cases only be
applied to kvm slots only before migration starts, that should be far
latter than kvm initializes (VM starts).
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201001012226.5868-1-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There's no good reason to use both the dirty bitmap logging and the
new dirty ring buffer to track dirty bits. We should be able to even
support both of them at the same time, but it could complicate things
which could actually help little. Let's simply make it the rule
before we enable dirty ring on any arch, that we don't allow these two
interfaces to be used together.
The big world switch would be KVM_CAP_DIRTY_LOG_RING capability
enablement. That's where we'll switch from the default dirty logging
way to the dirty ring way. As long as kvm->dirty_ring_size is setup
correctly, we'll once and for all switch to the dirty ring buffer mode
for the current virtual machine.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201001012224.5818-1-peterx@redhat.com>
[Change errno from EINVAL to ENXIO. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch is heavily based on previous work from Lei Cao
<lei.cao@stratus.com> and Paolo Bonzini <pbonzini@redhat.com>. [1]
KVM currently uses large bitmaps to track dirty memory. These bitmaps
are copied to userspace when userspace queries KVM for its dirty page
information. The use of bitmaps is mostly sufficient for live
migration, as large parts of memory are be dirtied from one log-dirty
pass to another. However, in a checkpointing system, the number of
dirty pages is small and in fact it is often bounded---the VM is
paused when it has dirtied a pre-defined number of pages. Traversing a
large, sparsely populated bitmap to find set bits is time-consuming,
as is copying the bitmap to user-space.
A similar issue will be there for live migration when the guest memory
is huge while the page dirty procedure is trivial. In that case for
each dirty sync we need to pull the whole dirty bitmap to userspace
and analyse every bit even if it's mostly zeros.
The preferred data structure for above scenarios is a dense list of
guest frame numbers (GFN). This patch series stores the dirty list in
kernel memory that can be memory mapped into userspace to allow speedy
harvesting.
This patch enables dirty ring for X86 only. However it should be
easily extended to other archs as well.
[1] https://patchwork.kernel.org/patch/10471409/
Signed-off-by: Lei Cao <lei.cao@stratus.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201001012222.5767-1-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The context will be needed to implement the kvm dirty ring.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201001012044.5151-5-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_clear_guest_page is not used anymore after "KVM: X86: Don't track dirty
for KVM_SET_[TSS_ADDR|IDENTITY_MAP_ADDR]", except from kvm_clear_guest.
We can just inline it in its sole user.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Don't allow the events to accumulate in the eventfd counter, drain them
as they are handled.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Message-Id: <20201027135523.646811-4-dwmw2@infradead.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As far as I can tell, when we use posted interrupts we silently cut off
the events from userspace, if it's listening on the same eventfd that
feeds the irqfd.
I like that behaviour. Let's do it all the time, even without posted
interrupts. It makes it much easier to handle IRQ remapping invalidation
without having to constantly add/remove the fd from the userspace poll
set. We can just leave userspace polling on it, and the bypass will...
well... bypass it.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Message-Id: <20201026175325.585623-2-dwmw2@infradead.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Dirty logging is a key feature of the KVM MMU and must be supported by
the TDP MMU. Add support for both the write protection and PML dirty
logging modes.
Tested by running kvm-unit-tests and KVM selftests on an Intel Haswell
machine. This series introduced no new failures.
This series can be viewed in Gerrit at:
https://linux-review.googlesource.com/c/virt/kvm/kvm/+/2538
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20201014182700.2888246-16-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cache the address space ID just like the slot ID. It will be used in
order to fill in the dirty ring entries.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201014182700.2888246-7-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make use of the struct_size() helper to avoid any potential type
mistakes and protect against potential integer overflows
Make use of the flex_array_size() helper to calculate the size of a
flexible array member within an enclosing structure
Suggested-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Rustam Kovhaev <rkovhaev@gmail.com>
Message-Id: <20200918120500.954436-1-rkovhaev@gmail.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is no need to calculate wildcard in each iteration
since wildcard is not changed.
Signed-off-by: Yi Li <yili@winhong.com>
Message-Id: <20200911055652.3041762-1-yili@winhong.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
when kmalloc() fails in kvm_io_bus_unregister_dev(), before removing
the bus, we should iterate over all other devices linked to it and call
kvm_iodevice_destructor() for them
Fixes: 90db10434b ("KVM: kvm_io_bus_unregister_dev() should never fail")
Cc: stable@vger.kernel.org
Reported-and-tested-by: syzbot+f196caa45793d6374707@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=f196caa45793d6374707
Signed-off-by: Rustam Kovhaev <rkovhaev@gmail.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200907185535.233114-1-rkovhaev@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Multiple stolen time fixes, with a new capability to match x86
- Fix for hugetlbfs mappings when PUD and PMD are the same level
- Fix for hugetlbfs mappings when PTE mappings are enforced
(dirty logging, for example)
- Fix tracing output of 64bit values
-----BEGIN PGP SIGNATURE-----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=VBrL
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for Linux 5.9, take #1
- Multiple stolen time fixes, with a new capability to match x86
- Fix for hugetlbfs mappings when PUD and PMD are the same level
- Fix for hugetlbfs mappings when PTE mappings are enforced
(dirty logging, for example)
- Fix tracing output of 64bit values
The 'flags' field of 'struct mmu_notifier_range' is used to indicate
whether invalidate_range_{start,end}() are permitted to block. In the
case of kvm_mmu_notifier_invalidate_range_start(), this field is not
forwarded on to the architecture-specific implementation of
kvm_unmap_hva_range() and therefore the backend cannot sensibly decide
whether or not to block.
Add an extra 'flags' parameter to kvm_unmap_hva_range() so that
architectures are aware as to whether or not they are permitted to block.
Cc: <stable@vger.kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Message-Id: <20200811102725.7121-2-will@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Merge more updates from Andrew Morton:
- most of the rest of MM (memcg, hugetlb, vmscan, proc, compaction,
mempolicy, oom-kill, hugetlbfs, migration, thp, cma, util,
memory-hotplug, cleanups, uaccess, migration, gup, pagemap),
- various other subsystems (alpha, misc, sparse, bitmap, lib, bitops,
checkpatch, autofs, minix, nilfs, ufs, fat, signals, kmod, coredump,
exec, kdump, rapidio, panic, kcov, kgdb, ipc).
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (164 commits)
mm/gup: remove task_struct pointer for all gup code
mm: clean up the last pieces of page fault accountings
mm/xtensa: use general page fault accounting
mm/x86: use general page fault accounting
mm/sparc64: use general page fault accounting
mm/sparc32: use general page fault accounting
mm/sh: use general page fault accounting
mm/s390: use general page fault accounting
mm/riscv: use general page fault accounting
mm/powerpc: use general page fault accounting
mm/parisc: use general page fault accounting
mm/openrisc: use general page fault accounting
mm/nios2: use general page fault accounting
mm/nds32: use general page fault accounting
mm/mips: use general page fault accounting
mm/microblaze: use general page fault accounting
mm/m68k: use general page fault accounting
mm/ia64: use general page fault accounting
mm/hexagon: use general page fault accounting
mm/csky: use general page fault accounting
...
After the cleanup of page fault accounting, gup does not need to pass
task_struct around any more. Remove that parameter in the whole gup
stack.
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Link: http://lkml.kernel.org/r/20200707225021.200906-26-peterx@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IRQ bypass support for vdpa and IFC
MLX5 vdpa driver
Endian-ness fixes for virtio drivers
Misc other fixes
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAl8yVEwPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpNPEH/0Dtq1s1V4r/kxtLUoMophv9wuORpWCr98BQ
2aOveTmwTOVdZVOiw2tzTgO9nbWx+cL2HvkU7Aajfpz5hh93Z2VOo2n4a7hBC79f
rlc3GXiG+pMk5RfmqGofIHTU+D6ony4D5SXlUDurLdtEwunyuqZwABiWkZjdclZJ
bv90IL8Upzbz0rxYr7k3z8UepdOCt7r4QS/o7STHZBjJRyylxmO/R2yTnh6PtpRK
Q/z35wJBJ3SKc8X3Fi0VOOSeGNZOiypkkl9ZnLVY5lExNAU1+2MMn2UK119SlCDV
MSxb7quYFF4cksXH1g77GMBNi1uADRh1dtFMZdkKhZGljGxKLxo=
=6VTZ
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
- IRQ bypass support for vdpa and IFC
- MLX5 vdpa driver
- Endianness fixes for virtio drivers
- Misc other fixes
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (71 commits)
vdpa/mlx5: fix up endian-ness for mtu
vdpa: Fix pointer math bug in vdpasim_get_config()
vdpa/mlx5: Fix pointer math in mlx5_vdpa_get_config()
vdpa/mlx5: fix memory allocation failure checks
vdpa/mlx5: Fix uninitialised variable in core/mr.c
vdpa_sim: init iommu lock
virtio_config: fix up warnings on parisc
vdpa/mlx5: Add VDPA driver for supported mlx5 devices
vdpa/mlx5: Add shared memory registration code
vdpa/mlx5: Add support library for mlx5 VDPA implementation
vdpa/mlx5: Add hardware descriptive header file
vdpa: Modify get_vq_state() to return error code
net/vdpa: Use struct for set/get vq state
vdpa: remove hard coded virtq num
vdpasim: support batch updating
vhost-vdpa: support IOTLB batching hints
vhost-vdpa: support get/set backend features
vhost: generialize backend features setting/getting
vhost-vdpa: refine ioctl pre-processing
vDPA: dont change vq irq after DRIVER_OK
...
- Untangle the header spaghetti which causes build failures in various
situations caused by the lockdep additions to seqcount to validate that
the write side critical sections are non-preemptible.
- The seqcount associated lock debug addons which were blocked by the
above fallout.
seqcount writers contrary to seqlock writers must be externally
serialized, which usually happens via locking - except for strict per
CPU seqcounts. As the lock is not part of the seqcount, lockdep cannot
validate that the lock is held.
This new debug mechanism adds the concept of associated locks.
sequence count has now lock type variants and corresponding
initializers which take a pointer to the associated lock used for
writer serialization. If lockdep is enabled the pointer is stored and
write_seqcount_begin() has a lockdep assertion to validate that the
lock is held.
Aside of the type and the initializer no other code changes are
required at the seqcount usage sites. The rest of the seqcount API is
unchanged and determines the type at compile time with the help of
_Generic which is possible now that the minimal GCC version has been
moved up.
Adding this lockdep coverage unearthed a handful of seqcount bugs which
have been addressed already independent of this.
While generaly useful this comes with a Trojan Horse twist: On RT
kernels the write side critical section can become preemtible if the
writers are serialized by an associated lock, which leads to the well
known reader preempts writer livelock. RT prevents this by storing the
associated lock pointer independent of lockdep in the seqcount and
changing the reader side to block on the lock when a reader detects
that a writer is in the write side critical section.
- Conversion of seqcount usage sites to associated types and initializers.
-----BEGIN PGP SIGNATURE-----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=7Gj+
-----END PGP SIGNATURE-----
Merge tag 'locking-urgent-2020-08-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Thomas Gleixner:
"A set of locking fixes and updates:
- Untangle the header spaghetti which causes build failures in
various situations caused by the lockdep additions to seqcount to
validate that the write side critical sections are non-preemptible.
- The seqcount associated lock debug addons which were blocked by the
above fallout.
seqcount writers contrary to seqlock writers must be externally
serialized, which usually happens via locking - except for strict
per CPU seqcounts. As the lock is not part of the seqcount, lockdep
cannot validate that the lock is held.
This new debug mechanism adds the concept of associated locks.
sequence count has now lock type variants and corresponding
initializers which take a pointer to the associated lock used for
writer serialization. If lockdep is enabled the pointer is stored
and write_seqcount_begin() has a lockdep assertion to validate that
the lock is held.
Aside of the type and the initializer no other code changes are
required at the seqcount usage sites. The rest of the seqcount API
is unchanged and determines the type at compile time with the help
of _Generic which is possible now that the minimal GCC version has
been moved up.
Adding this lockdep coverage unearthed a handful of seqcount bugs
which have been addressed already independent of this.
While generally useful this comes with a Trojan Horse twist: On RT
kernels the write side critical section can become preemtible if
the writers are serialized by an associated lock, which leads to
the well known reader preempts writer livelock. RT prevents this by
storing the associated lock pointer independent of lockdep in the
seqcount and changing the reader side to block on the lock when a
reader detects that a writer is in the write side critical section.
- Conversion of seqcount usage sites to associated types and
initializers"
* tag 'locking-urgent-2020-08-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
locking/seqlock, headers: Untangle the spaghetti monster
locking, arch/ia64: Reduce <asm/smp.h> header dependencies by moving XTP bits into the new <asm/xtp.h> header
x86/headers: Remove APIC headers from <asm/smp.h>
seqcount: More consistent seqprop names
seqcount: Compress SEQCNT_LOCKNAME_ZERO()
seqlock: Fold seqcount_LOCKNAME_init() definition
seqlock: Fold seqcount_LOCKNAME_t definition
seqlock: s/__SEQ_LOCKDEP/__SEQ_LOCK/g
hrtimer: Use sequence counter with associated raw spinlock
kvm/eventfd: Use sequence counter with associated spinlock
userfaultfd: Use sequence counter with associated spinlock
NFSv4: Use sequence counter with associated spinlock
iocost: Use sequence counter with associated spinlock
raid5: Use sequence counter with associated spinlock
vfs: Use sequence counter with associated spinlock
timekeeping: Use sequence counter with associated raw spinlock
xfrm: policy: Use sequence counters with associated lock
netfilter: nft_set_rbtree: Use sequence counter with associated rwlock
netfilter: conntrack: Use sequence counter with associated spinlock
sched: tasks: Use sequence counter with associated spinlock
...
x86:
* Report last CPU for debugging
* Emulate smaller MAXPHYADDR in the guest than in the host
* .noinstr and tracing fixes from Thomas
* nested SVM page table switching optimization and fixes
Generic:
* Unify shadow MMU cache data structures across architectures
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl8pC+oUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNcOwgAjomqtEqQNlp7DdZT7VyyklzbxX1/
ud7v+oOJ8K4sFlf64lSthjPo3N9rzZCcw+yOXmuyuITngXOGc3tzIwXpCzpLtuQ1
WO1Ql3B/2dCi3lP5OMmsO1UAZqy9pKLg1dfeYUPk48P5+p7d/NPmk+Em5kIYzKm5
JsaHfCp2EEXomwmljNJ8PQ1vTjIQSSzlgYUBZxmCkaaX7zbEUMtxAQCStHmt8B84
33LczwXBm3viSWrzsoBV37I70+tseugiSGsCfUyupXOvq55d6D9FCqtCb45Hn4Vh
Ik8ggKdalsk/reiGEwNw1/3nr6mRMkHSbl+Mhc4waOIFf9dn0urgQgOaDg==
=YVx0
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"s390:
- implement diag318
x86:
- Report last CPU for debugging
- Emulate smaller MAXPHYADDR in the guest than in the host
- .noinstr and tracing fixes from Thomas
- nested SVM page table switching optimization and fixes
Generic:
- Unify shadow MMU cache data structures across architectures"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (127 commits)
KVM: SVM: Fix sev_pin_memory() error handling
KVM: LAPIC: Set the TDCR settable bits
KVM: x86: Specify max TDP level via kvm_configure_mmu()
KVM: x86/mmu: Rename max_page_level to max_huge_page_level
KVM: x86: Dynamically calculate TDP level from max level and MAXPHYADDR
KVM: VXM: Remove temporary WARN on expected vs. actual EPTP level mismatch
KVM: x86: Pull the PGD's level from the MMU instead of recalculating it
KVM: VMX: Make vmx_load_mmu_pgd() static
KVM: x86/mmu: Add separate helper for shadow NPT root page role calc
KVM: VMX: Drop a duplicate declaration of construct_eptp()
KVM: nSVM: Correctly set the shadow NPT root level in its MMU role
KVM: Using macros instead of magic values
MIPS: KVM: Fix build error caused by 'kvm_run' cleanup
KVM: nSVM: remove nonsensical EXITINFO1 adjustment on nested NPF
KVM: x86: Add a capability for GUEST_MAXPHYADDR < HOST_MAXPHYADDR support
KVM: VMX: optimize #PF injection when MAXPHYADDR does not match
KVM: VMX: Add guest physical address check in EPT violation and misconfig
KVM: VMX: introduce vmx_need_pf_intercept
KVM: x86: update exception bitmap on CPUID changes
KVM: x86: rename update_bp_intercept to update_exception_bitmap
...
If failed to connect, there is no need to start consumer nor
producer.
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Suggested-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20200731065533.4144-7-lingshan.zhu@intel.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A sequence counter write side critical section must be protected by some
form of locking to serialize writers. A plain seqcount_t does not
contain the information of which lock must be held when entering a write
side critical section.
Use the new seqcount_spinlock_t data type, which allows to associate a
spinlock with the sequence counter. This enables lockdep to verify that
the spinlock used for writer serialization is held when the write side
critical section is entered.
If lockdep is disabled this lock association is compiled out and has
neither storage size nor runtime overhead.
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Link: https://lkml.kernel.org/r/20200720155530.1173732-24-a.darwish@linutronix.de
Entering a guest is similar to exiting to user space. Pending work like
handling signals, rescheduling, task work etc. needs to be handled before
that.
Provide generic infrastructure to avoid duplication of the same handling
code all over the place.
The transfer to guest mode handling is different from the exit to usermode
handling, e.g. vs. rseq and live patching, so a separate function is used.
The initial list of work items handled is:
TIF_SIGPENDING, TIF_NEED_RESCHED, TIF_NOTIFY_RESUME
Architecture specific TIF flags can be added via defines in the
architecture specific include files.
The calling convention is also different from the syscall/interrupt entry
functions as KVM invokes this from the outer vcpu_run() loop with
interrupts and preemption enabled. To prevent missing a pending work item
it invokes a check for pending TIF work from interrupt disabled code right
before transitioning to guest mode. The lockdep, RCU and tracing state
handling is also done directly around the switch to and from guest mode.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20200722220519.833296398@linutronix.de
Move x86's memory cache helpers to common KVM code so that they can be
reused by arm64 and MIPS in future patches.
Suggested-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200703023545.8771-16-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
OVMF booted guest running on shadow pages crashes on TRIPLE FAULT after
enabling paging from SMM. The crash is triggered from mmu_check_root() and
is caused by kvm_is_visible_gfn() searching through memslots with as_id = 0
while vCPU may be in a different context (address space).
Introduce kvm_vcpu_is_visible_gfn() and use it from mmu_check_root().
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200708140023.1476020-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Unlike normal 'int' functions returning '0' on success, kvm_setup_async_pf()/
kvm_arch_setup_async_pf() return '1' when a job to handle page fault
asynchronously was scheduled and '0' otherwise. To avoid the confusion
change return type to 'bool'.
No functional change intended.
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200615121334.91300-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Sparse complains on a call to get_compat_sigset, fix it. The "if"
right above explains that sigmask_arg->sigset is basically a
compat_sigset_t.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Loongson port
PPC:
- Fixes
ARM:
- Fixes
x86:
- KVM_SET_USER_MEMORY_REGION optimizations
- Fixes
- Selftest fixes
The guest side of the asynchronous page fault work has been delayed to 5.9
in order to sync with Thomas's interrupt entry rework.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl7icj4UHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroPHGQgAj9+5j+f5v06iMP/+ponWwsVfh+5/
UR1gPbpMSFMKF0U+BCFxsBeGKWPDiz9QXaLfy6UGfOFYBI475Su5SoZ8/i/o6a2V
QjcKIJxBRNs66IG/774pIpONY8/mm/3b6vxmQktyBTqjb6XMGlOwoGZixj/RTp85
+uwSICxMlrijg+fhFMwC4Bo/8SFg+FeBVbwR07my88JaLj+3cV/NPolG900qLSa6
uPqJ289EQ86LrHIHXCEWRKYvwy77GFsmBYjKZH8yXpdzUlSGNexV8eIMAz50figu
wYRJGmHrRqwuzFwEGknv8SA3s2HVggXO4WVkWWCeJyO8nIVfYFUhME5l6Q==
=+Hh0
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more KVM updates from Paolo Bonzini:
"The guest side of the asynchronous page fault work has been delayed to
5.9 in order to sync with Thomas's interrupt entry rework, but here's
the rest of the KVM updates for this merge window.
MIPS:
- Loongson port
PPC:
- Fixes
ARM:
- Fixes
x86:
- KVM_SET_USER_MEMORY_REGION optimizations
- Fixes
- Selftest fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (62 commits)
KVM: x86: do not pass poisoned hva to __kvm_set_memory_region
KVM: selftests: fix sync_with_host() in smm_test
KVM: async_pf: Inject 'page ready' event only if 'page not present' was previously injected
KVM: async_pf: Cleanup kvm_setup_async_pf()
kvm: i8254: remove redundant assignment to pointer s
KVM: x86: respect singlestep when emulating instruction
KVM: selftests: Don't probe KVM_CAP_HYPERV_ENLIGHTENED_VMCS when nested VMX is unsupported
KVM: selftests: do not substitute SVM/VMX check with KVM_CAP_NESTED_STATE check
KVM: nVMX: Consult only the "basic" exit reason when routing nested exit
KVM: arm64: Move hyp_symbol_addr() to kvm_asm.h
KVM: arm64: Synchronize sysreg state on injecting an AArch32 exception
KVM: arm64: Make vcpu_cp1x() work on Big Endian hosts
KVM: arm64: Remove host_cpu_context member from vcpu structure
KVM: arm64: Stop sparse from moaning at __hyp_this_cpu_ptr
KVM: arm64: Handle PtrAuth traps early
KVM: x86: Unexport x86_fpu_cache and make it static
KVM: selftests: Ignore KVM 5-level paging support for VM_MODE_PXXV48_4K
KVM: arm64: Save the host's PtrAuth keys in non-preemptible context
KVM: arm64: Stop save/restoring ACTLR_EL1
KVM: arm64: Add emulation for 32bit guests accessing ACTLR2
...
'Page not present' event may or may not get injected depending on
guest's state. If the event wasn't injected, there is no need to
inject the corresponding 'page ready' event as the guest may get
confused. E.g. Linux thinks that the corresponding 'page not present'
event wasn't delivered *yet* and allocates a 'dummy entry' for it.
This entry is never freed.
Note, 'wakeup all' events have no corresponding 'page not present'
event and always get injected.
s390 seems to always be able to inject 'page not present', the
change is effectively a nop.
Suggested-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200610175532.779793-2-vkuznets@redhat.com>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=208081
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
schedule_work() returns 'false' only when the work is already on the queue
and this can't happen as kvm_setup_async_pf() always allocates a new one.
Also, to avoid potential race, it makes sense to to schedule_work() at the
very end after we've added it to the queue.
While on it, do some minor cleanup. gfn_to_pfn_async() mentioned in a
comment does not currently exist and, moreover, we can check
kvm_is_error_hva() at the very beginning, before we try to allocate work so
'retry_sync' label can go away completely.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200610175532.779793-1-vkuznets@redhat.com>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Patch series "mm: consolidate definitions of page table accessors", v2.
The low level page table accessors (pXY_index(), pXY_offset()) are
duplicated across all architectures and sometimes more than once. For
instance, we have 31 definition of pgd_offset() for 25 supported
architectures.
Most of these definitions are actually identical and typically it boils
down to, e.g.
static inline unsigned long pmd_index(unsigned long address)
{
return (address >> PMD_SHIFT) & (PTRS_PER_PMD - 1);
}
static inline pmd_t *pmd_offset(pud_t *pud, unsigned long address)
{
return (pmd_t *)pud_page_vaddr(*pud) + pmd_index(address);
}
These definitions can be shared among 90% of the arches provided
XYZ_SHIFT, PTRS_PER_XYZ and xyz_page_vaddr() are defined.
For architectures that really need a custom version there is always
possibility to override the generic version with the usual ifdefs magic.
These patches introduce include/linux/pgtable.h that replaces
include/asm-generic/pgtable.h and add the definitions of the page table
accessors to the new header.
This patch (of 12):
The linux/mm.h header includes <asm/pgtable.h> to allow inlining of the
functions involving page table manipulations, e.g. pte_alloc() and
pmd_alloc(). So, there is no point to explicitly include <asm/pgtable.h>
in the files that include <linux/mm.h>.
The include statements in such cases are remove with a simple loop:
for f in $(git grep -l "include <linux/mm.h>") ; do
sed -i -e '/include <asm\/pgtable.h>/ d' $f
done
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-1-rppt@kernel.org
Link: http://lkml.kernel.org/r/20200514170327.31389-2-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
API __get_user_pages_fast() renamed to get_user_pages_fast_only() to
align with pin_user_pages_fast_only().
As part of this we will get rid of write parameter. Instead caller will
pass FOLL_WRITE to get_user_pages_fast_only(). This will not change any
existing functionality of the API.
All the callers are changed to pass FOLL_WRITE.
Also introduce get_user_page_fast_only(), and use it in a few places
that hard-code nr_pages to 1.
Updated the documentation of the API.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org> [arch/powerpc/kvm]
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Michal Suchanek <msuchanek@suse.de>
Link: http://lkml.kernel.org/r/1590396812-31277-1-git-send-email-jrdr.linux@gmail.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b1394e745b ("KVM: x86: fix APIC page invalidation") tried
to fix inappropriate APIC page invalidation by re-introducing arch
specific kvm_arch_mmu_notifier_invalidate_range() and calling it from
kvm_mmu_notifier_invalidate_range_start. However, the patch left a
possible race where the VMCS APIC address cache is updated *before*
it is unmapped:
(Invalidator) kvm_mmu_notifier_invalidate_range_start()
(Invalidator) kvm_make_all_cpus_request(kvm, KVM_REQ_APIC_PAGE_RELOAD)
(KVM VCPU) vcpu_enter_guest()
(KVM VCPU) kvm_vcpu_reload_apic_access_page()
(Invalidator) actually unmap page
Because of the above race, there can be a mismatch between the
host physical address stored in the APIC_ACCESS_PAGE VMCS field and
the host physical address stored in the EPT entry for the APIC GPA
(0xfee0000). When this happens, the processor will not trap APIC
accesses, and will instead show the raw contents of the APIC-access page.
Because Windows OS periodically checks for unexpected modifications to
the LAPIC register, this will show up as a BSOD crash with BugCheck
CRITICAL_STRUCTURE_CORRUPTION (109) we are currently seeing in
https://bugzilla.redhat.com/show_bug.cgi?id=1751017.
The root cause of the issue is that kvm_arch_mmu_notifier_invalidate_range()
cannot guarantee that no additional references are taken to the pages in
the range before kvm_mmu_notifier_invalidate_range_end(). Fortunately,
this case is supported by the MMU notifier API, as documented in
include/linux/mmu_notifier.h:
* If the subsystem
* can't guarantee that no additional references are taken to
* the pages in the range, it has to implement the
* invalidate_range() notifier to remove any references taken
* after invalidate_range_start().
The fix therefore is to reload the APIC-access page field in the VMCS
from kvm_mmu_notifier_invalidate_range() instead of ..._range_start().
Cc: stable@vger.kernel.org
Fixes: b1394e745b ("KVM: x86: fix APIC page invalidation")
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=197951
Signed-off-by: Eiichi Tsukata <eiichi.tsukata@nutanix.com>
Message-Id: <20200606042627.61070-1-eiichi.tsukata@nutanix.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After commit 63d0434 ("KVM: x86: move kvm_create_vcpu_debugfs after
last failure point") we are creating the pre-vCPU debugfs files
after the creation of the vCPU file descriptor. This makes it
possible for userspace to reach kvm_vcpu_release before
kvm_create_vcpu_debugfs has finished. The vcpu->debugfs_dentry
then does not have any associated inode anymore, and this causes
a NULL-pointer dereference in debugfs_create_file.
The solution is simply to avoid removing the files; they are
cleaned up when the VM file descriptor is closed (and that must be
after KVM_CREATE_VCPU returns). We can stop storing the dentry
in struct kvm_vcpu too, because it is not needed anywhere after
kvm_create_vcpu_debugfs returns.
Reported-by: syzbot+705f4401d5a93a59b87d@syzkaller.appspotmail.com
Fixes: 63d0434837 ("KVM: x86: move kvm_create_vcpu_debugfs after last failure point")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Move the arch-specific code into arch/arm64/kvm
- Start the post-32bit cleanup
- Cherry-pick a few non-invasive pre-NV patches
-----BEGIN PGP SIGNATURE-----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=aD+9
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 updates for Linux 5.8:
- Move the arch-specific code into arch/arm64/kvm
- Start the post-32bit cleanup
- Cherry-pick a few non-invasive pre-NV patches
The userspace_addr alignment and range checks are not performed for private
memory slots that are prepared by KVM itself. This is unnecessary and makes
it questionable to use __*_user functions to access memory later on. We also
rely on the userspace address being aligned since we have an entire family
of functions to map gfn to pfn.
Fortunately skipping the check is completely unnecessary. Only x86 uses
private memslots and their userspace_addr is obtained from vm_mmap,
therefore it must be below PAGE_OFFSET. In fact, any attempt to pass
an address above PAGE_OFFSET would have failed because such an address
would return true for kvm_is_error_hva.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If two page ready notifications happen back to back the second one is not
delivered and the only mechanism we currently have is
kvm_check_async_pf_completion() check in vcpu_run() loop. The check will
only be performed with the next vmexit when it happens and in some cases
it may take a while. With interrupt based page ready notification delivery
the situation is even worse: unlike exceptions, interrupts are not handled
immediately so we must check if the slot is empty. This is slow and
unnecessary. Introduce dedicated MSR_KVM_ASYNC_PF_ACK MSR to communicate
the fact that the slot is free and host should check its notification
queue. Mandate using it for interrupt based 'page ready' APF event
delivery.
As kvm_check_async_pf_completion() is going away from vcpu_run() we need
a way to communicate the fact that vcpu->async_pf.done queue has
transitioned from empty to non-empty state. Introduce
kvm_arch_async_page_present_queued() and KVM_REQ_APF_READY to do the job.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200525144125.143875-7-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
An innocent reader of the following x86 KVM code:
bool kvm_arch_can_inject_async_page_present(struct kvm_vcpu *vcpu)
{
if (!(vcpu->arch.apf.msr_val & KVM_ASYNC_PF_ENABLED))
return true;
...
may get very confused: if APF mechanism is not enabled, why do we report
that we 'can inject async page present'? In reality, upon injection
kvm_arch_async_page_present() will check the same condition again and,
in case APF is disabled, will just drop the item. This is fine as the
guest which deliberately disabled APF doesn't expect to get any APF
notifications.
Rename kvm_arch_can_inject_async_page_present() to
kvm_arch_can_dequeue_async_page_present() to make it clear what we are
checking: if the item can be dequeued (meaning either injected or just
dropped).
On s390 kvm_arch_can_inject_async_page_present() always returns 'true' so
the rename doesn't matter much.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200525144125.143875-4-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reverts commit 5b494aea13.
If unlocked==true then the vma pointer could be invalidated, so the 2nd
follow_pfn() is potentially racy: we do need to get out and redo
find_vma_intersection().
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that the 32bit KVM/arm host is a distant memory, let's move the
whole of the KVM/arm64 code into the arm64 tree.
As they said in the song: Welcome Home (Sanitarium).
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20200513104034.74741-1-maz@kernel.org
Two new stats for exposing halt-polling cpu usage:
halt_poll_success_ns
halt_poll_fail_ns
Thus sum of these 2 stats is the total cpu time spent polling. "success"
means the VCPU polled until a virtual interrupt was delivered. "fail"
means the VCPU had to schedule out (either because the maximum poll time
was reached or it needed to yield the CPU).
To avoid touching every arch's kvm_vcpu_stat struct, only update and
export halt-polling cpu usage stats if we're on x86.
Exporting cpu usage as a u64 and in nanoseconds means we will overflow at
~500 years, which seems reasonably large.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Jon Cargille <jcargill@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <20200508182240.68440-1-jcargill@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While optimizing posted-interrupt delivery especially for the timer
fastpath scenario, I measured kvm_x86_ops.deliver_posted_interrupt()
to introduce substantial latency because the processor has to perform
all vmentry tasks, ack the posted interrupt notification vector,
read the posted-interrupt descriptor etc.
This is not only slow, it is also unnecessary when delivering an
interrupt to the current CPU (as is the case for the LAPIC timer) because
PIR->IRR and IRR->RVI synchronization is already performed on vmentry
Therefore skip kvm_vcpu_trigger_posted_interrupt in this case, and
instead do vmx_sync_pir_to_irr() on the EXIT_FASTPATH_REENTER_GUEST
fastpath as well.
Tested-by: Haiwei Li <lihaiwei@tencent.com>
Cc: Haiwei Li <lihaiwei@tencent.com>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1588055009-12677-6-git-send-email-wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
hva_to_pfn_remapped() calls fixup_user_fault(), which has already
handled the retry gracefully. Even if "unlocked" is set to true, it
means that we've got a VM_FAULT_RETRY inside fixup_user_fault(),
however the page fault has already retried and we should have the pfn
set correctly. No need to do that again.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20200416155906.267462-1-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The '==' expression itself is bool, no need to convert it to bool again.
This fixes the following coccicheck warning:
virt/kvm/eventfd.c:724:38-43: WARNING: conversion to bool not needed
here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Message-Id: <20200420123805.4494-1-yanaijie@huawei.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The use of any sort of waitqueue (simple or regular) for
wait/waking vcpus has always been an overkill and semantically
wrong. Because this is per-vcpu (which is blocked) there is
only ever a single waiting vcpu, thus no need for any sort of
queue.
As such, make use of the rcuwait primitive, with the following
considerations:
- rcuwait already provides the proper barriers that serialize
concurrent waiter and waker.
- Task wakeup is done in rcu read critical region, with a
stable task pointer.
- Because there is no concurrency among waiters, we need
not worry about rcuwait_wait_event() calls corrupting
the wait->task. As a consequence, this saves the locking
done in swait when modifying the queue. This also applies
to per-vcore wait for powerpc kvm-hv.
The x86 tscdeadline_latency test mentioned in 8577370fb0
("KVM: Use simple waitqueue for vcpu->wq") shows that, on avg,
latency is reduced by around 15-20% with this change.
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: kvmarm@lists.cs.columbia.edu
Cc: linux-mips@vger.kernel.org
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Message-Id: <20200424054837.5138-6-dave@stgolabs.net>
[Avoid extra logic changes. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This allows making request to all other vcpus except the one
specified in the parameter.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Message-Id: <1588771076-73790-2-git-send-email-suravee.suthikulpanit@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In the unlikely event that a 32bit vcpu traps into the hypervisor
on an instruction that is located right at the end of the 32bit
range, the emulation of that instruction is going to increment
PC past the 32bit range. This isn't great, as userspace can then
observe this value and get a bit confused.
Conversly, userspace can do things like (in the context of a 64bit
guest that is capable of 32bit EL0) setting PSTATE to AArch64-EL0,
set PC to a 64bit value, change PSTATE to AArch32-USR, and observe
that PC hasn't been truncated. More confusion.
Fix both by:
- truncating PC increments for 32bit guests
- sanitizing all 32bit regs every time a core reg is changed by
userspace, and that PSTATE indicates a 32bit mode.
Cc: stable@vger.kernel.org
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
KVM now expects to be able to use HW-accelerated delivery of vSGIs
as soon as the guest has enabled thm. Unfortunately, we only
initialize the GICv4 context if we have a virtual ITS exposed to
the guest.
Fix it by always initializing the GICv4.1 context if it is
available on the host.
Fixes: 2291ff2f2a ("KVM: arm64: GICv4.1: Plumb SGI implementation selection in the distributor")
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
KVM_CAP_HALT_POLL is a per-VM capability that lets userspace
control the halt-polling time, allowing halt-polling to be tuned or
disabled on particular VMs.
With dynamic halt-polling, a VM's VCPUs can poll from anywhere from
[0, halt_poll_ns] on each halt. KVM_CAP_HALT_POLL sets the
upper limit on the poll time.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Jon Cargille <jcargill@google.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Message-Id: <20200417221446.108733-1-jcargill@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If we're going to fail out the vgic_add_lpi(), let's make sure the
allocated vgic_irq memory is also freed. Though it seems that both
cases are unlikely to fail.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200414030349.625-3-yuzenghui@huawei.com
It's likely that the vcpu fails to handle all virtual interrupts if
userspace decides to destroy it, leaving the pending ones stay in the
ap_list. If the un-handled one is a LPI, its vgic_irq structure will
be eventually leaked because of an extra refcount increment in
vgic_queue_irq_unlock().
This was detected by kmemleak on almost every guest destroy, the
backtrace is as follows:
unreferenced object 0xffff80725aed5500 (size 128):
comm "CPU 5/KVM", pid 40711, jiffies 4298024754 (age 166366.512s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 08 01 a9 73 6d 80 ff ff ...........sm...
c8 61 ee a9 00 20 ff ff 28 1e 55 81 6c 80 ff ff .a... ..(.U.l...
backtrace:
[<000000004bcaa122>] kmem_cache_alloc_trace+0x2dc/0x418
[<0000000069c7dabb>] vgic_add_lpi+0x88/0x418
[<00000000bfefd5c5>] vgic_its_cmd_handle_mapi+0x4dc/0x588
[<00000000cf993975>] vgic_its_process_commands.part.5+0x484/0x1198
[<000000004bd3f8e3>] vgic_its_process_commands+0x50/0x80
[<00000000b9a65b2b>] vgic_mmio_write_its_cwriter+0xac/0x108
[<0000000009641ebb>] dispatch_mmio_write+0xd0/0x188
[<000000008f79d288>] __kvm_io_bus_write+0x134/0x240
[<00000000882f39ac>] kvm_io_bus_write+0xe0/0x150
[<0000000078197602>] io_mem_abort+0x484/0x7b8
[<0000000060954e3c>] kvm_handle_guest_abort+0x4cc/0xa58
[<00000000e0d0cd65>] handle_exit+0x24c/0x770
[<00000000b44a7fad>] kvm_arch_vcpu_ioctl_run+0x460/0x1988
[<0000000025fb897c>] kvm_vcpu_ioctl+0x4f8/0xee0
[<000000003271e317>] do_vfs_ioctl+0x160/0xcd8
[<00000000e7f39607>] ksys_ioctl+0x98/0xd8
Fix it by retiring all pending LPIs in the ap_list on the destroy path.
p.s. I can also reproduce it on a normal guest shutdown. It is because
userspace still send LPIs to vcpu (through KVM_SIGNAL_MSI ioctl) while
the guest is being shutdown and unable to handle it. A little strange
though and haven't dig further...
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
[maz: moved the distributor deallocation down to avoid an UAF splat]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200414030349.625-2-yuzenghui@huawei.com
There is no point in accessing the HW when writing to any of the
ISPENDR/ICPENDR registers from userspace, as only the guest should
be allowed to change the HW state.
Introduce new userspace-specific accessors that deal solely with
the virtual state. Note that the API differs from that of GICv3,
where userspace exclusively uses ISPENDR to set the state. Too
bad we can't reuse it.
Fixes: 82e40f558d ("KVM: arm/arm64: vgic-v2: Handle SGI bits in GICD_I{S,C}PENDR0 as WI")
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
There is no point in accessing the HW when writing to any of the
ISENABLER/ICENABLER registers from userspace, as only the guest
should be allowed to change the HW state.
Introduce new userspace-specific accessors that deal solely with
the virtual state.
Reported-by: James Morse <james.morse@arm.com>
Tested-by: James Morse <james.morse@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
When a guest tries to read the active state of its interrupts,
we currently just return whatever state we have in memory. This
means that if such an interrupt lives in a List Register on another
CPU, we fail to obsertve the latest active state for this interrupt.
In order to remedy this, stop all the other vcpus so that they exit
and we can observe the most recent value for the state. This is
similar to what we are doing for the write side of the same
registers, and results in new MMIO handlers for userspace (which
do not need to stop the guest, as it is supposed to be stopped
already).
Reported-by: Julien Grall <julien@xen.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
When a nested page fault is taken from an address that does not have
a memslot associated to it, kvm_mmu_do_page_fault returns RET_PF_EMULATE
(via mmu_set_spte) and kvm_mmu_page_fault then invokes svm_need_emulation_on_page_fault.
The default answer there is to return false, but in this case this just
causes the page fault to be retried ad libitum. Since this is not a
fast path, and the only other case where it is taken is an erratum,
just stick a kvm_vcpu_gfn_to_memslot check in there to detect the
common case where the erratum is not happening.
This fixes an infinite loop in the new set_memory_region_test.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In earlier versions of kvm, 'kvm_run' was an independent structure
and was not included in the vcpu structure. At present, 'kvm_run'
is already included in the vcpu structure, so the parameter
'kvm_run' is redundant.
This patch simplifies the function definition, removes the extra
'kvm_run' parameter, and extracts it from the 'kvm_vcpu' structure
if necessary.
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Message-Id: <20200416051057.26526-1-tianjia.zhang@linux.alibaba.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Create a new function kvm_is_visible_memslot() and use it from
kvm_is_visible_gfn(); use the new function in try_async_pf() too,
to avoid an extra memslot lookup.
Opportunistically squish a multi-line comment into a single-line comment.
Note, the end result, KVM_PFN_NOSLOT, is unchanged.
Cc: Jim Mattson <jmattson@google.com>
Cc: Rick Edgecombe <rick.p.edgecombe@intel.com>
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The placement of kvm_create_vcpu_debugfs is more or less irrelevant, since
it cannot fail and userspace should not care about the debugfs entries until
it knows the vcpu has been created. Moving it after the last failure
point removes the need to remove the directory when unwinding the creation.
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20200331224222.393439-1-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Implementing (and even advertising) 64bit PSCI functions to 32bit
guests is at least a bit odd, if not altogether violating the
spec which says ("5.2.1 Register usage in arguments and return values"):
"Adherence to the SMC Calling Conventions implies that any AArch32
caller of an SMC64 function will get a return code of 0xFFFFFFFF(int32).
This matches the NOT_SUPPORTED error code used in PSCI"
Tighten the implementation by pretending these functions are not
there for 32bit guests.
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
When a guest delibarately uses an SMC32 function number (which is allowed),
we should make sure we drop the top 32bits from the input arguments, as they
could legitimately be junk.
Reported-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The variable r is being assigned with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Message-Id: <20200410113526.13822-1-colin.king@canonical.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When deciding whether a guest has to be stopped we check whether this
is a private interrupt or not. Unfortunately, there's an off-by-one bug
here, and we fail to recognize a whole range of interrupts as being
global (GICv2 SPIs 32-63).
Fix the condition from > to be >=.
Cc: stable@vger.kernel.org
Fixes: abd7229626 ("KVM: arm/arm64: Simplify active_change_prepare and plug race")
Reported-by: André Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Pass @opaque to kvm_arch_hardware_setup() and
kvm_arch_check_processor_compat() to allow architecture specific code to
reference @opaque without having to stash it away in a temporary global
variable. This will enable x86 to separate its vendor specific callback
ops, which are passed via @opaque, into "init" and "runtime" ops without
having to stash away the "init" ops.
No functional change intended.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Tested-by: Cornelia Huck <cohuck@redhat.com> #s390
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200321202603.19355-2-sean.j.christopherson@intel.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reset the LRU slot if it becomes invalid when deleting a memslot to fix
an out-of-bounds/use-after-free access when searching through memslots.
Explicitly check for there being no used slots in search_memslots(), and
in the caller of s390's approximation variant.
Fixes: 36947254e5 ("KVM: Dynamically size memslot array based on number of used slots")
Reported-by: Qian Cai <cai@lca.pw>
Cc: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200320205546.2396-2-sean.j.christopherson@intel.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The vgic-state debugfs file could do with showing the pending state
of the HW-backed SGIs. Plug it into the low-level code.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200304203330.4967-24-maz@kernel.org
Each time a Group-enable bit gets flipped, the state of these bits
needs to be forwarded to the hardware. This is a pretty heavy
handed operation, requiring all vcpus to reload their GICv4
configuration. It is thus implemented as a new request type.
These enable bits are programmed into the HW by setting the VGrp{0,1}En
fields of GICR_VPENDBASER when the vPEs are made resident again.
Of course, we only support Group-1 for now...
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20200304203330.4967-22-maz@kernel.org
The GICv4.1 architecture gives the hypervisor the option to let
the guest choose whether it wants the good old SGIs with an
active state, or the new, HW-based ones that do not have one.
For this, plumb the configuration of SGIs into the GICv3 MMIO
handling, present the GICD_TYPER2.nASSGIcap to the guest,
and handle the GICD_CTLR.nASSGIreq setting.
In order to be able to deal with the restore of a guest, also
apply the GICD_CTLR.nASSGIreq setting at first run so that we
can move the restored SGIs to the HW if that's what the guest
had selected in a previous life.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20200304203330.4967-21-maz@kernel.org
In order to let a guest buy in the new, active-less SGIs, we
need to be able to switch between the two modes.
Handle this by stopping all guest activity, transfer the state
from one mode to the other, and resume the guest. Nothing calls
this code so far, but a later patch will plug it into the MMIO
emulation.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20200304203330.4967-20-maz@kernel.org
Most of the GICv3 emulation code that deals with SGIs now has to be
aware of the v4.1 capabilities in order to benefit from it.
Add such support, keyed on the interrupt having the hw flag set and
being a SGI.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200304203330.4967-19-maz@kernel.org
As GICv4.1 understands the life cycle of doorbells (instead of
just randomly firing them at the most inconvenient time), just
enable them at irq_request time, and be done with it.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200304203330.4967-18-maz@kernel.org
In order to hide some of the differences between v4.0 and v4.1, move
the doorbell management out of the KVM code, and into the GICv4-specific
layer. This allows the calling code to ask for the doorbell when blocking,
and otherwise to leave the doorbell permanently disabled.
This matches the v4.1 code perfectly, and only results in a minor
refactoring of the v4.0 code.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20200304203330.4967-14-maz@kernel.org
Drop largepages_enabled, kvm_largepages_enabled() and
kvm_disable_largepages() now that all users are gone.
Note, largepages_enabled was an x86-only flag that got left in common
KVM code when KVM gained support for multiple architectures.
No functional change intended.
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It could take kvm->mmu_lock for an extended period of time when
enabling dirty log for the first time. The main cost is to clear
all the D-bits of last level SPTEs. This situation can benefit from
manual dirty log protect as well, which can reduce the mmu_lock
time taken. The sequence is like this:
1. Initialize all the bits of the dirty bitmap to 1 when enabling
dirty log for the first time
2. Only write protect the huge pages
3. KVM_GET_DIRTY_LOG returns the dirty bitmap info
4. KVM_CLEAR_DIRTY_LOG will clear D-bit for each of the leaf level
SPTEs gradually in small chunks
Under the Intel(R) Xeon(R) Gold 6152 CPU @ 2.10GHz environment,
I did some tests with a 128G windows VM and counted the time taken
of memory_global_dirty_log_start, here is the numbers:
VM Size Before After optimization
128G 460ms 10ms
Signed-off-by: Jay Zhou <jianjay.zhou@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove includes of asm/kvm_host.h from files that already include
linux/kvm_host.h to make it more obvious that there is no ordering issue
between the two headers. linux/kvm_host.h includes asm/kvm_host.h to
pick up architecture specific settings, and this will never change, i.e.
including asm/kvm_host.h after linux/kvm_host.h may seem problematic,
but in practice is simply redundant.
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that the memslot logic doesn't assume memslots are always non-NULL,
dynamically size the array of memslots instead of unconditionally
allocating memory for the maximum number of memslots.
Note, because a to-be-deleted memslot must first be invalidated, the
array size cannot be immediately reduced when deleting a memslot.
However, consecutive deletions will realize the memory savings, i.e.
a second deletion will trim the entry.
Tested-by: Christoffer Dall <christoffer.dall@arm.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Refactor memslot handling to treat the number of used slots as the de
facto size of the memslot array, e.g. return NULL from id_to_memslot()
when an invalid index is provided instead of relying on npages==0 to
detect an invalid memslot. Rework the sorting and walking of memslots
in advance of dynamically sizing memslots to aid bisection and debug,
e.g. with luck, a bug in the refactoring will bisect here and/or hit a
WARN instead of randomly corrupting memory.
Alternatively, a global null/invalid memslot could be returned, i.e. so
callers of id_to_memslot() don't have to explicitly check for a NULL
memslot, but that approach runs the risk of introducing difficult-to-
debug issues, e.g. if the global null slot is modified. Constifying
the return from id_to_memslot() to combat such issues is possible, but
would require a massive refactoring of arch specific code and would
still be susceptible to casting shenanigans.
Add function comments to update_memslots() and search_memslots() to
explicitly (and loudly) state how memslots are sorted.
Opportunistically stuff @hva with a non-canonical value when deleting a
private memslot on x86 to detect bogus usage of the freed slot.
No functional change intended.
Tested-by: Christoffer Dall <christoffer.dall@arm.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rework kvm_get_dirty_log() so that it "returns" the associated memslot
on success. A future patch will rework memslot handling such that
id_to_memslot() can return NULL, returning the memslot makes it more
obvious that the validity of the memslot has been verified, i.e.
precludes the need to add validity checks in the arch code that are
technically unnecessary.
To maintain ordering in s390, move the call to kvm_arch_sync_dirty_log()
from s390's kvm_vm_ioctl_get_dirty_log() to the new kvm_get_dirty_log().
This is a nop for PPC, the only other arch that doesn't select
KVM_GENERIC_DIRTYLOG_READ_PROTECT, as its sync_dirty_log() is empty.
Ideally, moving the sync_dirty_log() call would be done in a separate
patch, but it can't be done in a follow-on patch because that would
temporarily break s390's ordering. Making the move in a preparatory
patch would be functionally correct, but would create an odd scenario
where the moved sync_dirty_log() would operate on a "different" memslot
due to consuming the result of a different id_to_memslot(). The
memslot couldn't actually be different as slots_lock is held, but the
code is confusing enough as it is, i.e. moving sync_dirty_log() in this
patch is the lesser of all evils.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the implementations of KVM_GET_DIRTY_LOG and KVM_CLEAR_DIRTY_LOG
for CONFIG_KVM_GENERIC_DIRTYLOG_READ_PROTECT into common KVM code.
The arch specific implemenations are extremely similar, differing
only in whether the dirty log needs to be sync'd from hardware (x86)
and how the TLBs are flushed. Add new arch hooks to handle sync
and TLB flush; the sync will also be used for non-generic dirty log
support in a future patch (s390).
The ulterior motive for providing a common implementation is to
eliminate the dependency between arch and common code with respect to
the memslot referenced by the dirty log, i.e. to make it obvious in the
code that the validity of the memslot is guaranteed, as a future patch
will rework memslot handling such that id_to_memslot() can return NULL.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Clean up __kvm_set_memory_region() to achieve several goals:
- Remove local variables that serve no real purpose
- Improve the readability of the code
- Better show the relationship between the 'old' and 'new' memslot
- Prepare for dynamically sizing memslots
- Document subtle gotchas (via comments)
Note, using 'tmp' to hold the initial memslot is not strictly necessary
at this juncture, e.g. 'old' could be directly copied from
id_to_memslot(), but keep the pointer usage as id_to_memslot() will be
able to return a NULL pointer once memslots are dynamically sized.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that all callers of kvm_free_memslot() pass NULL for @dont, remove
the param from the top-level routine and all arch's implementations.
No functional change intended.
Tested-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move memslot deletion into its own routine so that the success path for
other memslot updates does not need to use kvm_free_memslot(), i.e. can
explicitly destroy the dirty bitmap when necessary. This paves the way
for dropping @dont from kvm_free_memslot(), i.e. all callers now pass
NULL for @dont.
Add a comment above the code to make a copy of the existing memslot
prior to deletion, it is not at all obvious that the pointer will become
stale during sorting and/or installation of new memslots.
Note, kvm_arch_commit_memory_region() allows an architecture to free
resources when moving a memslot or changing its flags, e.g. x86 frees
its arch specific memslot metadata during commit_memory_region().
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Tested-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Drop the "const" attribute from @old in kvm_arch_commit_memory_region()
to allow arch specific code to free arch specific resources in the old
memslot without having to cast away the attribute. Freeing resources in
kvm_arch_commit_memory_region() paves the way for simplifying
kvm_free_memslot() by eliminating the last usage of its @dont param.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Split out the core functionality of setting a memslot into a separate
helper in preparation for moving memslot deletion into its own routine.
Tested-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace a big pile o' gotos with returns to make it more obvious what
error code is being returned, and to prepare for refactoring the
functional, i.e. post-checks, portion of __kvm_set_memory_region().
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Explicitly free an allocated-but-unused dirty bitmap instead of relying
on kvm_free_memslot() if an error occurs in __kvm_set_memory_region().
There is no longer a need to abuse kvm_free_memslot() to free arch
specific resources as arch specific code is now called only after the
common flow is guaranteed to succeed. Arch code can still fail, but
it's responsible for its own cleanup in that case.
Eliminating the error path's abuse of kvm_free_memslot() paves the way
for simplifying kvm_free_memslot(), i.e. dropping its @dont param.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove kvm_arch_create_memslot() now that all arch implementations are
effectively nops. Removing kvm_arch_create_memslot() eliminates the
possibility for arch specific code to allocate memory prior to setting
a memslot, which sets the stage for simplifying kvm_free_memslot().
Cc: Janosch Frank <frankja@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The two implementations of kvm_arch_create_memslot() in x86 and PPC are
both good citizens and free up all local resources if creation fails.
Return immediately (via a superfluous goto) instead of calling
kvm_free_memslot().
Note, the call to kvm_free_memslot() is effectively an expensive nop in
this case as there are no resources to be freed.
No functional change intended.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reinstall the old memslots if preparing the new memory region fails
after invalidating a to-be-{re}moved memslot.
Remove the superfluous 'old_memslots' variable so that it's somewhat
clear that the error handling path needs to free the unused memslots,
not simply the 'old' memslots.
Fixes: bc6678a33d ("KVM: introduce kvm->srcu and convert kvm_set_memory_region to SRCU update")
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use the physical timer structure when reading the physical counter
instead of using the virtual timer structure. Thankfully, nothing is
accessing this code path yet (at least not until we enable save/restore
of the physical counter). It doesn't hurt for this to be correct though.
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
[maz: amended commit log]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Fixes: 84135d3d18 ("KVM: arm/arm64: consolidate arch timer trap handlers")
Link: https://lore.kernel.org/r/1584351546-5018-1-git-send-email-karahmed@amazon.de
- Fix compilation on 32bit
- Move VHE guest entry/exit into the VHE-specific entry code
- Make sure all functions called by the non-VHE HYP code is tagged as __always_inline
-----BEGIN PGP SIGNATURE-----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=NpPo
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm fixes for 5.6, take #1
- Fix compilation on 32bit
- Move VHE guest entry/exit into the VHE-specific entry code
- Make sure all functions called by the non-VHE HYP code is tagged as __always_inline
With VHE, running a vCPU always requires the sequence:
1. kvm_arm_vhe_guest_enter();
2. kvm_vcpu_run_vhe();
3. kvm_arm_vhe_guest_exit()
... and as we invoke this from the shared arm/arm64 KVM code, 32-bit arm
has to provide stubs for all three functions.
To simplify the common code, and make it easier to make further
modifications to the arm64-specific portions in the near future, let's
fold kvm_arm_vhe_guest_enter() and kvm_arm_vhe_guest_exit() into
kvm_vcpu_run_vhe().
The 32-bit stubs for kvm_arm_vhe_guest_enter() and
kvm_arm_vhe_guest_exit() are removed, as they are no longer used. The
32-bit stub for kvm_vcpu_run_vhe() is left as-is.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200210114757.2889-1-mark.rutland@arm.com
Accessing a per-cpu variable only makes sense when preemption is
disabled (and the kernel does check this when the right debug options
are switched on).
For kvm_get_running_vcpu(), it is fine to return the value after
re-enabling preemption, as the preempt notifiers will make sure that
this is kept consistent across task migration (the comment above the
function hints at it, but lacks the crucial preemption management).
While we're at it, move the comment from the ARM code, which explains
why the whole thing works.
Fixes: 7495e22bb1 ("KVM: Move running VCPU from ARM to common code").
Cc: Paolo Bonzini <pbonzini@redhat.com>
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Tested-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/318984f6-bc36-33a3-abc6-bf2295974b06@huawei.com
Message-id: <20200207163410.31276-1-maz@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fedora kernel builds on armv7hl began failing recently because
kvm_arm_exception_type and kvm_arm_exception_class were undeclared in
trace.h. Add the missing include.
Fixes: 0e20f5e255 ("KVM: arm/arm64: Cleanup MMIO handling")
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200205134146.82678-1-jcline@redhat.com
From Boris Ostrovsky:
The KVM hypervisor may provide a guest with ability to defer remote TLB
flush when the remote VCPU is not running. When this feature is used,
the TLB flush will happen only when the remote VPCU is scheduled to run
again. This will avoid unnecessary (and expensive) IPIs.
Under certain circumstances, when a guest initiates such deferred action,
the hypervisor may miss the request. It is also possible that the guest
may mistakenly assume that it has already marked remote VCPU as needing
a flush when in fact that request had already been processed by the
hypervisor. In both cases this will result in an invalid translation
being present in a vCPU, potentially allowing accesses to memory locations
in that guest's address space that should not be accessible.
Note that only intra-guest memory is vulnerable.
The five patches address both of these problems:
1. The first patch makes sure the hypervisor doesn't accidentally clear
a guest's remote flush request
2. The rest of the patches prevent the race between hypervisor
acknowledging a remote flush request and guest issuing a new one.
Conflicts:
arch/x86/kvm/x86.c [move from kvm_arch_vcpu_free to kvm_arch_vcpu_destroy]
__kvm_map_gfn()'s call to gfn_to_pfn_memslot() is
* relatively expensive
* in certain cases (such as when done from atomic context) cannot be called
Stashing gfn-to-pfn mapping should help with both cases.
This is part of CVE-2019-3016.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_vcpu_(un)map operates on gfns from any current address space.
In certain cases we want to make sure we are not mapping SMRAM
and for that we can use kvm_(un)map_gfn() that we are introducing
in this patch.
This is part of CVE-2019-3016.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to the ARM ARM, registers CNT{P,V}_TVAL_EL0 have bits [63:32]
RES0 [1]. When reading the register, the value is truncated to the least
significant 32 bits [2], and on writes, TimerValue is treated as a signed
32-bit integer [1, 2].
When the guest behaves correctly and writes 32-bit values, treating TVAL
as an unsigned 64 bit register works as expected. However, things start
to break down when the guest writes larger values, because
(u64)0x1_ffff_ffff = 8589934591. but (s32)0x1_ffff_ffff = -1, and the
former will cause the timer interrupt to be asserted in the future, but
the latter will cause it to be asserted now. Let's treat TVAL as a
signed 32-bit register on writes, to match the behaviour described in
the architecture, and the behaviour experimentally exhibited by the
virtual timer on a non-vhe host.
[1] Arm DDI 0487E.a, section D13.8.18
[2] Arm DDI 0487E.a, section D11.2.4
Signed-off-by: Alexandru Elisei <alexandru.elisei@arm.com>
[maz: replaced the read-side mask with lower_32_bits]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Fixes: 8fa7616248 ("KVM: arm/arm64: arch_timer: Fix CNTP_TVAL calculation")
Link: https://lore.kernel.org/r/20200127103652.2326-1-alexandru.elisei@arm.com
Let the code never use unsupported event counters. Change
kvm_pmu_handle_pmcr() to only reset supported counters and
kvm_pmu_vcpu_reset() to only stop supported counters.
Other actions are filtered on the supported counters in
kvm/sysregs.c
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200124142535.29386-5-eric.auger@redhat.com
At the moment a SW_INCR counter always overflows on 32-bit
boundary, independently on whether the n+1th counter is
programmed as CHAIN.
Check whether the SW_INCR counter is a 64b counter and if so,
implement the 64b logic.
Fixes: 80f393a23b ("KVM: arm/arm64: Support chained PMU counters")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200124142535.29386-4-eric.auger@redhat.com
At the moment we update the chain bitmap on type setting. This
does not take into account the enable state of the odd register.
Let's make sure a counter is never considered as chained if
the high counter is disabled.
We recompute the chain state on enable/disable and type changes.
Also let create_perf_event() use the chain bitmap and not use
kvm_pmu_idx_has_chain_evtype().
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200124142535.29386-3-eric.auger@redhat.com
The specification says PMSWINC increments PMEVCNTR<n>_EL1 by 1
if PMEVCNTR<n>_EL0 is enabled and configured to count SW_INCR.
For PMEVCNTR<n>_EL0 to be enabled, we need both PMCNTENSET to
be set for the corresponding event counter but we also need
the PMCR.E bit to be set.
Fixes: 7a0adc7064 ("arm64: KVM: Add access handler for PMSWINC register")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200124142535.29386-2-eric.auger@redhat.com
Avoid the "writable" check in __gfn_to_hva_many(), which will always fail
on read-only memslots due to gfn_to_hva() assuming writes. Functionally,
this allows x86 to create large mappings for read-only memslots that
are backed by HugeTLB mappings.
Note, the changelog for commit 05da45583d ("KVM: MMU: large page
support") states "If the largepage contains write-protected pages, a
large pte is not used.", but "write-protected" refers to pages that are
temporarily read-only, e.g. read-only memslots didn't even exist at the
time.
Fixes: 4d8b81abc4 ("KVM: introduce readonly memslot")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
[Redone using kvm_vcpu_gfn_to_memslot_prot. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use kvm_vcpu_gfn_to_hva() when retrieving the host page size so that the
correct set of memslots is used when handling x86 page faults in SMM.
Fixes: 54bf36aac5 ("KVM: x86: use vcpu-specific functions to read/write/translate GFNs")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a helper, is_transparent_hugepage(), to explicitly check whether a
compound page is a THP and use it when populating KVM's secondary MMU.
The explicit check fixes a bug where a remapped compound page, e.g. for
an XDP Rx socket, is mapped into a KVM guest and is mistaken for a THP,
which results in KVM incorrectly creating a huge page in its secondary
MMU.
Fixes: 936a5fe6e6 ("thp: kvm mmu transparent hugepage support")
Reported-by: syzbot+c9d1fb51ac9d0d10c39d@syzkaller.appspotmail.com
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Check the result of __kvm_gfn_to_hva_cache_init() and return immediately
instead of relying on the kvm_is_error_hva() check to detect errors so
that it's abundantly clear KVM intends to immediately bail on an error.
Note, the hva check is still mandatory to handle errors on subqeuesnt
calls with the same generation. Similarly, always return -EFAULT on
error so that multiple (bad) calls for a given generation will get the
same result, e.g. on an illegal gfn wrap, propagating the return from
__kvm_gfn_to_hva_cache_init() would cause the initial call to return
-EINVAL and subsequent calls to return -EFAULT.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Barret reported a (technically benign) bug where nr_pages_avail can be
accessed without being initialized if gfn_to_hva_many() fails.
virt/kvm/kvm_main.c:2193:13: warning: 'nr_pages_avail' may be
used uninitialized in this function [-Wmaybe-uninitialized]
Rather than simply squashing the warning by initializing nr_pages_avail,
fix the underlying issues by reworking __kvm_gfn_to_hva_cache_init() to
return immediately instead of continuing on. Now that all callers check
the result and/or bail immediately on a bad hva, there's no need to
explicitly nullify the memslot on error.
Reported-by: Barret Rhoden <brho@google.com>
Fixes: f1b9dd5eb8 ("kvm: Disallow wraparound in kvm_gfn_to_hva_cache_init")
Cc: Jim Mattson <jmattson@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When reading/writing using the guest/host cache, check for a bad hva
before checking for a NULL memslot, which triggers the slow path for
handing cross-page accesses. Because the memslot is nullified on error
by __kvm_gfn_to_hva_cache_init(), if the bad hva is encountered after
crossing into a new page, then the kvm_{read,write}_guest() slow path
could potentially write/access the first chunk prior to detecting the
bad hva.
Arguably, performing a partial access is semantically correct from an
architectural perspective, but that behavior is certainly not intended.
In the original implementation, memslot was not explicitly nullified
and therefore the partial access behavior varied based on whether the
memslot itself was null, or if the hva was simply bad. The current
behavior was introduced as a seemingly unintentional side effect in
commit f1b9dd5eb8 ("kvm: Disallow wraparound in
kvm_gfn_to_hva_cache_init"), which justified the change with "since some
callers don't check the return code from this function, it sit seems
prudent to clear ghc->memslot in the event of an error".
Regardless of intent, the partial access is dependent on _not_ checking
the result of the cache initialization, which is arguably a bug in its
own right, at best simply weird.
Fixes: 8f964525a1 ("KVM: Allow cross page reads and writes from cached translations.")
Cc: Jim Mattson <jmattson@google.com>
Cc: Andrew Honig <ahonig@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For ring-based dirty log tracking, it will be more efficient to account
writes during schedule-out or schedule-in to the currently running VCPU.
We would like to do it even if the write doesn't use the current VCPU's
address space, as is the case for cached writes (see commit 4e335d9e7d,
"Revert "KVM: Support vCPU-based gfn->hva cache"", 2017-05-02).
Therefore, add a mechanism to track the currently-loaded kvm_vcpu struct.
There is already something similar in KVM/ARM; one important difference
is that kvm_arch_vcpu_{load,put} have two callers in virt/kvm/kvm_main.c:
we have to update both the architecture-independent vcpu_{load,put} and
the preempt notifiers.
Another change made in the process is to allow using kvm_get_running_vcpu()
in preemptible code. This is allowed because preempt notifiers ensure
that the value does not change even after the VCPU thread is migrated.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's already going to reach 2400 Bytes (which is over half of page
size on 4K page archs), so maybe it's good to have this build-time
check in case it overflows when adding new fields.
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove kvm_read_guest_atomic() because it's not used anywhere.
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Open code the allocation and freeing of the vcpu->run page in
kvm_vm_ioctl_create_vcpu() and kvm_vcpu_destroy() respectively. Doing
so allows kvm_vcpu_init() to be a pure init function and eliminates
kvm_vcpu_uninit() entirely.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the putting of vcpu->pid to kvm_vcpu_destroy(). vcpu->pid is
guaranteed to be NULL when kvm_vcpu_uninit() is called in the error path
of kvm_vm_ioctl_create_vcpu(), e.g. it is explicitly nullified by
kvm_vcpu_init() and is only changed by KVM_RUN.
No functional change intended.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove kvm_arch_vcpu_init() and kvm_arch_vcpu_uninit() now that all
arch specific implementations are nops.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add an arm specific hook to free the arm64-only sve_state. Doing so
eliminates the last functional code from kvm_arch_vcpu_uninit() across
all architectures and paves the way for removing kvm_arch_vcpu_init()
and kvm_arch_vcpu_uninit() entirely.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fold init() into create() now that the two are called back-to-back by
common KVM code (kvm_vcpu_init() calls kvm_arch_vcpu_init() as its last
action, and kvm_vm_ioctl_create_vcpu() calls kvm_arch_vcpu_create()
immediately thereafter). This paves the way for removing
kvm_arch_vcpu_{un}init() entirely.
Note, there is no associated unwinding in kvm_arch_vcpu_uninit() that
needs to be relocated (to kvm_arch_vcpu_destroy()).
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove kvm_arch_vcpu_setup() now that all arch specific implementations
are nops.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Initialize the preempt notifier immediately in kvm_vcpu_init() to pave
the way for removing kvm_arch_vcpu_setup(), i.e. to allow arch specific
code to call vcpu_load() during kvm_arch_vcpu_create().
Back when preemption support was added, the location of the call to init
the preempt notifier was perfectly sane. The overall vCPU creation flow
featured a single arch specific hook and the preempt notifer was used
immediately after its initialization (by vcpu_load()). E.g.:
vcpu = kvm_arch_ops->vcpu_create(kvm, n);
if (IS_ERR(vcpu))
return PTR_ERR(vcpu);
preempt_notifier_init(&vcpu->preempt_notifier, &kvm_preempt_ops);
vcpu_load(vcpu);
r = kvm_mmu_setup(vcpu);
vcpu_put(vcpu);
if (r < 0)
goto free_vcpu;
Today, the call to preempt_notifier_init() is sandwiched between two
arch specific calls, kvm_arch_vcpu_create() and kvm_arch_vcpu_setup(),
which needlessly forces x86 (and possibly others?) to split its vCPU
creation flow. Init the preempt notifier prior to any arch specific
call so that each arch can independently decide how best to organize
its creation flow.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Unexport kvm_vcpu_cache and kvm_vcpu_{un}init() and make them static
now that they are referenced only in kvm_main.c.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that all architectures tightly couple vcpu allocation/free with the
mandatory calls to kvm_{un}init_vcpu(), move the sequences verbatim to
common KVM code.
Move both allocation and initialization in a single patch to eliminate
thrash in arch specific code. The bisection benefits of moving the two
pieces in separate patches is marginal at best, whereas the odds of
introducing a transient arch specific bug are non-zero.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add kvm_vcpu_destroy() and wire up all architectures to call the common
function instead of their arch specific implementation. The common
destruction function will be used by future patches to move allocation
and initialization of vCPUs to common KVM code, i.e. to free resources
that are allocated by arch agnostic code.
No functional change intended.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a pre-allocation arch hook to handle checks that are currently done
by arch specific code prior to allocating the vCPU object. This paves
the way for moving the allocation to common KVM code.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove the superfluous kvm_arch_vcpu_free() as it is no longer called
from commmon KVM code. Note, kvm_arch_vcpu_destroy() *is* called from
common code, i.e. choosing which function to whack is not completely
arbitrary.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM's inject_abt64() injects an external-abort into an aarch64 guest.
The KVM_CAP_ARM_INJECT_EXT_DABT is intended to do exactly this, but
for an aarch32 guest inject_abt32() injects an implementation-defined
exception, 'Lockdown fault'.
Change this to external abort. For non-LPAE we now get the documented:
| Unhandled fault: external abort on non-linefetch (0x008) at 0x9c800f00
and for LPAE:
| Unhandled fault: synchronous external abort (0x210) at 0x9c800f00
Fixes: 74a64a9816 ("KVM: arm/arm64: Unify 32bit fault injection")
Reported-by: Beata Michalska <beata.michalska@linaro.org>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200121123356.203000-3-james.morse@arm.com
Beata reports that KVM_SET_VCPU_EVENTS doesn't inject the expected
exception to a non-LPAE aarch32 guest.
The host intends to inject DFSR.FS=0x14 "IMPLEMENTATION DEFINED fault
(Lockdown fault)", but the guest receives DFSR.FS=0x04 "Fault on
instruction cache maintenance". This fault is hooked by
do_translation_fault() since ARMv6, which goes on to silently 'handle'
the exception, and restart the faulting instruction.
It turns out, when TTBCR.EAE is clear DFSR is split, and FS[4] has
to shuffle up to DFSR[10].
As KVM only does this in one place, fix up the static values. We
now get the expected:
| Unhandled fault: lock abort (0x404) at 0x9c800f00
Fixes: 74a64a9816 ("KVM: arm/arm64: Unify 32bit fault injection")
Reported-by: Beata Michalska <beata.michalska@linaro.org>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200121123356.203000-2-james.morse@arm.com
kvm_test_age_hva() is called upon mmu_notifier_test_young(), but wrong
address range has been passed to handle_hva_to_gpa(). With the wrong
address range, no young bits will be checked in handle_hva_to_gpa().
It means zero is always returned from mmu_notifier_test_young().
This fixes the issue by passing correct address range to the underly
function handle_hva_to_gpa(), so that the hardware young (access) bit
will be visited.
Fixes: 35307b9a5f ("arm/arm64: KVM: Implement Stage-2 page aging")
Signed-off-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200121055659.19560-1-gshan@redhat.com
Our MMIO handling is a bit odd, in the sense that it uses an
intermediate per-vcpu structure to store the various decoded
information that describe the access.
But the same information is readily available in the HSR/ESR_EL2
field, and we actually use this field to populate the structure.
Let's simplify the whole thing by getting rid of the superfluous
structure and save a (tiny) bit of space in the vcpu structure.
[32bit fix courtesy of Olof Johansson <olof@lixom.net>]
Signed-off-by: Marc Zyngier <maz@kernel.org>
The wrappers make it less clear that the position of the call
to kvm_arch_async_page_present depends on the architecture, and
that only one of the two call sites will actually be active.
Remove them.
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We can store reference to kvm_stats_debugfs_item instead of copying
its values to kvm_stat_data.
This allows us to remove duplicated code and usage of temporary
kvm_stat_data inside vm_stat_get et al.
Signed-off-by: Milan Pandurov <milanpa@amazon.de>
Reviewed-by: Alexander Graf <graf@amazon.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fix some wrong function names in comment. mmu_check_roots is a typo for
mmu_check_root, vmcs_read_any should be vmcs12_read_any and so on.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_vgic_register_mmio_region() was introduced in commit 4493b1c486
("KVM: arm/arm64: vgic-new: Add MMIO handling framework") but never
used, and even never implemented. Remove it to avoid confusing readers.
Reported-by: Haibin Wang <wanghaibin.wang@huawei.com>
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200119090604.398-1-yuzenghui@huawei.com
Discard is supposed to fail if the collection is not mapped to any
target redistributor. We currently check if the collection is mapped
by "ite->collection" but this is incomplete (e.g., mapping a LPI to
an unmapped collection also results in a non NULL ite->collection).
What actually needs to be checked is its_is_collection_mapped(), let's
turn to it.
Also take this chance to remove an extra blank line.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20200114112212.1411-1-yuzenghui@huawei.com
Confusingly, there are three SPSR layouts that a kernel may need to deal
with:
(1) An AArch64 SPSR_ELx view of an AArch64 pstate
(2) An AArch64 SPSR_ELx view of an AArch32 pstate
(3) An AArch32 SPSR_* view of an AArch32 pstate
When the KVM AArch32 support code deals with SPSR_{EL2,HYP}, it's either
dealing with #2 or #3 consistently. On arm64 the PSR_AA32_* definitions
match the AArch64 SPSR_ELx view, and on arm the PSR_AA32_* definitions
match the AArch32 SPSR_* view.
However, when we inject an exception into an AArch32 guest, we have to
synthesize the AArch32 SPSR_* that the guest will see. Thus, an AArch64
host needs to synthesize layout #3 from layout #2.
This patch adds a new host_spsr_to_spsr32() helper for this, and makes
use of it in the KVM AArch32 support code. For arm64 we need to shuffle
the DIT bit around, and remove the SS bit, while for arm we can use the
value as-is.
I've open-coded the bit manipulation for now to avoid having to rework
the existing PSR_* definitions into PSR64_AA32_* and PSR32_AA32_*
definitions. I hope to perform a more thorough refactoring in future so
that we can handle pstate view manipulation more consistently across the
kernel tree.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200108134324.46500-4-mark.rutland@arm.com
When KVM injects an exception into a guest, it generates the CPSR value
from scratch, configuring CPSR.{M,A,I,T,E}, and setting all other
bits to zero.
This isn't correct, as the architecture specifies that some CPSR bits
are (conditionally) cleared or set upon an exception, and others are
unchanged from the original context.
This patch adds logic to match the architectural behaviour. To make this
simple to follow/audit/extend, documentation references are provided,
and bits are configured in order of their layout in SPSR_EL2. This
layout can be seen in the diagram on ARM DDI 0487E.a page C5-426.
Note that this code is used by both arm and arm64, and is intended to
fuction with the SPSR_EL2 and SPSR_HYP layouts.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200108134324.46500-3-mark.rutland@arm.com
When we check for a poisoned page, we use the VMA to tell userspace
about the looming disaster. But we pass a pointer to this VMA
after having released the mmap_sem, which isn't a good idea.
Instead, stash the shift value that goes with this pfn while
we are holding the mmap_sem.
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Link: https://lore.kernel.org/r/20191211165651.7889-3-maz@kernel.org
Link: https://lore.kernel.org/r/20191217123809.197392-1-james.morse@arm.com
It doesn't needs to call hyp_cpu_pm_exit() in init_hyp_mode() when some
error occurs. hyp_cpu_pm_exit() only needs to be called in
kvm_arch_init() if init_subsystems() fails. So move hyp_cpu_pm_exit()
out from teardown_hyp_mode() and call it directly in kvm_arch_init().
Signed-off-by: Shannon Zhao <shannon.zhao@linux.alibaba.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1575272531-3204-1-git-send-email-shannon.zhao@linux.alibaba.com
Although guest will hardly read and use the PTZ (Pending Table Zero)
bit in GICR_PENDBASER, let us emulate the architecture strictly.
As per IHI 0069E 9.11.30, PTZ field is WO, and reads as 0.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20191220111833.1422-1-yuzenghui@huawei.com
Saving/restoring an unmapped collection is a valid scenario. For
example this happens if a MAPTI command was sent, featuring an
unmapped collection. At the moment the CTE fails to be restored.
Only compare against the number of online vcpus if the rdist
base is set.
Fixes: ea1ad53e1e ("KVM: arm64: vgic-its: Collection table save/restore")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20191213094237.19627-1-eric.auger@redhat.com
On AArch64 you can do a sign-extended load to either a 32-bit or 64-bit
register, and we should only sign extend the register up to the width of
the register as specified in the operation (by using the 32-bit Wn or
64-bit Xn register specifier).
As it turns out, the architecture provides this decoding information in
the SF ("Sixty-Four" -- how cute...) bit.
Let's take advantage of this with the usual 32-bit/64-bit header file
dance and do the right thing on AArch64 hosts.
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191212195055.5541-1-christoffer.dall@arm.com
Convert a plethora of parameters and variables in the MMU and page fault
flows from type gva_t to gpa_t to properly handle TDP on 32-bit KVM.
Thanks to PSE and PAE paging, 32-bit kernels can access 64-bit physical
addresses. When TDP is enabled, the fault address is a guest physical
address and thus can be a 64-bit value, even when both KVM and its guest
are using 32-bit virtual addressing, e.g. VMX's VMCS.GUEST_PHYSICAL is a
64-bit field, not a natural width field.
Using a gva_t for the fault address means KVM will incorrectly drop the
upper 32-bits of the GPA. Ditto for gva_to_gpa() when it is used to
translate L2 GPAs to L1 GPAs.
Opportunistically rename variables and parameters to better reflect the
dual address modes, e.g. use "cr2_or_gpa" for fault addresses and plain
"addr" instead of "vaddr" when the address may be either a GVA or an L2
GPA. Similarly, use "gpa" in the nonpaging_page_fault() flows to avoid
a confusing "gpa_t gva" declaration; this also sets the stage for a
future patch to combing nonpaging_page_fault() and tdp_page_fault() with
minimal churn.
Sprinkle in a few comments to document flows where an address is known
to be a GVA and thus can be safely truncated to a 32-bit value. Add
WARNs in kvm_handle_page_fault() and FNAME(gva_to_gpa_nested)() to help
document such cases and detect bugs.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use out_err jump label to handle resource release. It's a
good practice to release resource in one place and help
eliminate some duplicated code.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use out_err jump label to handle resource release. It's a
good practice to release resource in one place and help
eliminate some duplicated code.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We can get rid of unnecessary var page in
kvm_set_pfn_dirty() , thus make code style
similar with kvm_set_pfn_accessed().
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Fix a bug where we try to do an ultracall on a system without an
ultravisor.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEv0VLfXa2m9eKuaRpnZrqdyxjcZ8FAl35s5kACgkQnZrqdyxj
cZ8cwwf/UPCvZIYPSeYvzrCrlA+wlhBAh3bh47+ZXaNybOpss1xZ7QOFGkgoVBkn
ES2Sdx3qgLvhmbR+nEKon8YCDVSwUj2ehwJu1nzAUzuVYw+m8OHGjdW07+go5KKi
xZOndwBQGYaaWxch2O8Qw27TZU4lcVY/FNQiti5Ahg9dKK98CLyMsWnTms23ZjGD
JMN/jCoMxa6godxWk3mSLaIwXj8P1P4pH3oiMFF8ngRTqyMgi1l02wim+DV10rD4
5JoAF2kzSYngDlrhhQAsSOWrsWst1X2txcHA2QsoL7ZGYUQzzKyHH6zC6dS9eWk4
ni70RLEnJj8YpsjwT52tFYokxwTPfQ==
=kPkE
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-fixes-5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into kvm-master
PPC KVM fix for 5.5
- Fix a bug where we try to do an ultracall on a system without an
ultravisor.
A device mapping is normally always mapped at Stage-2, since there
is very little gain in having it faulted in.
Nonetheless, it is possible to end-up in a situation where the device
mapping has been removed from Stage-2 (userspace munmaped the VFIO
region, and the MMU notifier did its job), but present in a userspace
mapping (userpace has mapped it back at the same address). In such
a situation, the device mapping will be demand-paged as the guest
performs memory accesses.
This requires to be careful when dealing with mapping size, cache
management, and to handle potential execution of a device mapping.
Reported-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Alexandru Elisei <alexandru.elisei@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191211165651.7889-2-maz@kernel.org
In kvm_arch_prepare_memory_region, arm kvm regards the memory region as
writable if the flag has no KVM_MEM_READONLY, and the vm is readonly if
!VM_WRITE.
But there is common usage for setting kvm memory region as follows:
e.g. qemu side (see the PROT_NONE flag)
1. mmap(NULL, size, PROT_NONE, MAP_ANONYMOUS | MAP_PRIVATE, -1, 0);
memory_region_init_ram_ptr()
2. re mmap the above area with read/write authority.
Such example is used in virtio-fs qemu codes which hasn't been upstreamed
[1]. But seems we can't forbid this example.
Without this patch, it will cause an EPERM during kvm_set_memory_region()
and cause qemu boot crash.
As told by Ard, "the underlying assumption is incorrect, i.e., that the
value of vm_flags at this point in time defines how the VMA is used
during its lifetime. There may be other cases where a VMA is created
with VM_READ vm_flags that are changed to VM_READ|VM_WRITE later, and
we are currently rejecting this use case as well."
[1] https://gitlab.com/virtio-fs/qemu/blob/5a356e/hw/virtio/vhost-user-fs.c#L488
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Jia He <justin.he@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Link: https://lore.kernel.org/r/20191206020802.196108-1-justin.he@arm.com
Use wrapper function lock_all_vcpus()/unlock_all_vcpus()
in kvm_vgic_create() to remove duplicated code dealing
with locking and unlocking all vcpus in a vm.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/1575081918-11401-1-git-send-email-linmiaohe@huawei.com
In kvm_vgic_dist_init() called from kvm_vgic_map_resources(), if
dist->vgic_model is invalid, dist->spis will be freed without set
dist->spis = NULL. And in vgicv2 resources clean up path,
__kvm_vgic_destroy() will be called to free allocated resources.
And dist->spis will be freed again in clean up chain because we
forget to set dist->spis = NULL in kvm_vgic_dist_init() failed
path. So double free would happen.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/1574923128-19956-1-git-send-email-linmiaohe@huawei.com
As arg dummy is not really needed, there's no need to pass
NULL when calling cpu_init_hyp_mode(). So clean it up.
Fixes: 67f6919766 ("arm64: kvm: allows kvm cpu hotplug")
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1574320559-5662-1-git-send-email-linmiaohe@huawei.com
The jump label out_free_1 and out_free_2 deal with
the same stuff, so git rid of one and rename the
label out_free_0a to retain the label name order.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Allow non-ISV data aborts to be reported to userspace
- Allow injection of data aborts from userspace
- Expose stolen time to guests
- GICv4 performance improvements
- vgic ITS emulation fixes
- Simplify FWB handling
- Enable halt pool counters
- Make the emulated timer PREEMPT_RT compliant
-----BEGIN PGP SIGNATURE-----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=SxBH
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm updates for Linux 5.5:
- Allow non-ISV data aborts to be reported to userspace
- Allow injection of data aborts from userspace
- Expose stolen time to guests
- GICv4 performance improvements
- vgic ITS emulation fixes
- Simplify FWB handling
- Enable halt pool counters
- Make the emulated timer PREEMPT_RT compliant
Conflicts:
include/uapi/linux/kvm.h
Fetching an index for any vcpu in kvm->vcpus array by traversing
the entire array everytime is costly.
This patch remembers the position of each vcpu in kvm->vcpus array
by storing it in vcpus_idx under kvm_vcpu structure.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Nitesh Narayan Lal <nitesh@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The out_err label and var ret is unnecessary, clean them up.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a comment explaining the rational behind having both
no_compat open and ioctl callbacks to fend off compat tasks.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On a system without KVM_COMPAT, we prevent IOCTLs from being issued
by a compat task. Although this prevents most silly things from
happening, it can still confuse a 32bit userspace that is able
to open the kvm device (the qemu test suite seems to be pretty
mad with this behaviour).
Take a more radical approach and return a -ENODEV to the compat
task.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VT-d posted interrupts, DAX/ZONE_DEVICE,
module unload/reload.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJdyrEsAAoJEL/70l94x66DIOkH/Asqrh4o4pwfRHWE+9rnM6PI
j8oFi7Q4eRXJnP4zEMnMbb6xD/BfSH1tWEcPcYgIxD/t0DFx8F92/xsETAJ/Qc5n
CWpmnhMkJqERlV+GSRuBqnheMo0CEH1Ab1QZKhh5U3//pK3OtGY9WyydJHWcquTh
bGh2pnxwVZOtIIEmclUUfKjyR2Fu8hJLnQwzWgYZ27UK7J2pLmiiTX0vwQG359Iq
sDn9ND33pCBW5e/D2mzccRjOJEvzwrumewM1sRDsoAYLJzUjg9+xD83vZDa1d7R6
gajCDFWVJbPoLvUY+DgsZBwMMlogElimJMT/Zft3ERbCsYJbFvcmwp4JzyxDxQ4=
=J6KN
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Fix unwinding of KVM_CREATE_VM failure, VT-d posted interrupts,
DAX/ZONE_DEVICE, and module unload/reload"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: MMU: Do not treat ZONE_DEVICE pages as being reserved
KVM: VMX: Introduce pi_is_pir_empty() helper
KVM: VMX: Do not change PID.NDST when loading a blocked vCPU
KVM: VMX: Consider PID.PIR to determine if vCPU has pending interrupts
KVM: VMX: Fix comment to specify PID.ON instead of PIR.ON
KVM: X86: Fix initialization of MSR lists
KVM: fix placement of refcount initialization
KVM: Fix NULL-ptr deref after kvm_create_vm fails
Explicitly exempt ZONE_DEVICE pages from kvm_is_reserved_pfn() and
instead manually handle ZONE_DEVICE on a case-by-case basis. For things
like page refcounts, KVM needs to treat ZONE_DEVICE pages like normal
pages, e.g. put pages grabbed via gup(). But for flows such as setting
A/D bits or shifting refcounts for transparent huge pages, KVM needs to
to avoid processing ZONE_DEVICE pages as the flows in question lack the
underlying machinery for proper handling of ZONE_DEVICE pages.
This fixes a hang reported by Adam Borowski[*] in dev_pagemap_cleanup()
when running a KVM guest backed with /dev/dax memory, as KVM straight up
doesn't put any references to ZONE_DEVICE pages acquired by gup().
Note, Dan Williams proposed an alternative solution of doing put_page()
on ZONE_DEVICE pages immediately after gup() in order to simplify the
auditing needed to ensure is_zone_device_page() is called if and only if
the backing device is pinned (via gup()). But that approach would break
kvm_vcpu_{un}map() as KVM requires the page to be pinned from map() 'til
unmap() when accessing guest memory, unlike KVM's secondary MMU, which
coordinates with mmu_notifier invalidations to avoid creating stale
page references, i.e. doesn't rely on pages being pinned.
[*] http://lkml.kernel.org/r/20190919115547.GA17963@angband.pl
Reported-by: Adam Borowski <kilobyte@angband.pl>
Analyzed-by: David Hildenbrand <david@redhat.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: stable@vger.kernel.org
Fixes: 3565fce3a6 ("mm, x86: get_user_pages() for dax mappings")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reported by syzkaller:
=============================
WARNING: suspicious RCU usage
-----------------------------
./include/linux/kvm_host.h:536 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
no locks held by repro_11/12688.
stack backtrace:
Call Trace:
dump_stack+0x7d/0xc5
lockdep_rcu_suspicious+0x123/0x170
kvm_dev_ioctl+0x9a9/0x1260 [kvm]
do_vfs_ioctl+0x1a1/0xfb0
ksys_ioctl+0x6d/0x80
__x64_sys_ioctl+0x73/0xb0
do_syscall_64+0x108/0xaa0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Commit a97b0e773e (kvm: call kvm_arch_destroy_vm if vm creation fails)
sets users_count to 1 before kvm_arch_init_vm(), however, if kvm_arch_init_vm()
fails, we need to decrease this count. By moving it earlier, we can push
the decrease to out_err_no_arch_destroy_vm without introducing yet another
error label.
syzkaller source: https://syzkaller.appspot.com/x/repro.c?x=15209b84e00000
Reported-by: syzbot+75475908cd0910f141ee@syzkaller.appspotmail.com
Fixes: a97b0e773e ("kvm: call kvm_arch_destroy_vm if vm creation fails")
Cc: Jim Mattson <jmattson@google.com>
Analyzed-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reported by syzkaller:
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 14727 Comm: syz-executor.3 Not tainted 5.4.0-rc4+ #0
RIP: 0010:kvm_coalesced_mmio_init+0x5d/0x110 arch/x86/kvm/../../../virt/kvm/coalesced_mmio.c:121
Call Trace:
kvm_dev_ioctl_create_vm arch/x86/kvm/../../../virt/kvm/kvm_main.c:3446 [inline]
kvm_dev_ioctl+0x781/0x1490 arch/x86/kvm/../../../virt/kvm/kvm_main.c:3494
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:509 [inline]
do_vfs_ioctl+0x196/0x1150 fs/ioctl.c:696
ksys_ioctl+0x62/0x90 fs/ioctl.c:713
__do_sys_ioctl fs/ioctl.c:720 [inline]
__se_sys_ioctl fs/ioctl.c:718 [inline]
__x64_sys_ioctl+0x6e/0xb0 fs/ioctl.c:718
do_syscall_64+0xca/0x5d0 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Commit 9121923c45 ("kvm: Allocate memslots and buses before calling kvm_arch_init_vm")
moves memslots and buses allocations around, however, if kvm->srcu/irq_srcu fails
initialization, NULL will be returned instead of error code, NULL will not be intercepted
in kvm_dev_ioctl_create_vm() and be dereferenced by kvm_coalesced_mmio_init(), this patch
fixes it.
Moving the initialization is required anyway to avoid an incorrect synchronize_srcu that
was also reported by syzkaller:
wait_for_completion+0x29c/0x440 kernel/sched/completion.c:136
__synchronize_srcu+0x197/0x250 kernel/rcu/srcutree.c:921
synchronize_srcu_expedited kernel/rcu/srcutree.c:946 [inline]
synchronize_srcu+0x239/0x3e8 kernel/rcu/srcutree.c:997
kvm_page_track_unregister_notifier+0xe7/0x130 arch/x86/kvm/page_track.c:212
kvm_mmu_uninit_vm+0x1e/0x30 arch/x86/kvm/mmu.c:5828
kvm_arch_destroy_vm+0x4a2/0x5f0 arch/x86/kvm/x86.c:9579
kvm_create_vm arch/x86/kvm/../../../virt/kvm/kvm_main.c:702 [inline]
so do it.
Reported-by: syzbot+89a8060879fa0bd2db4f@syzkaller.appspotmail.com
Reported-by: syzbot+e27e7027eb2b80e44225@syzkaller.appspotmail.com
Fixes: 9121923c45 ("kvm: Allocate memslots and buses before calling kvm_arch_init_vm")
Cc: Jim Mattson <jmattson@google.com>
Cc: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Just like we do for WFE trapping, it can be useful to turn off
WFI trapping when the physical CPU is not oversubscribed (that
is, the vcpu is the only runnable process on this CPU) *and*
that we're using direct injection of interrupts.
The conditions are reevaluated on each vcpu_load(), ensuring that
we don't switch to this mode on a busy system.
On a GICv4 system, this has the effect of reducing the generation
of doorbell interrupts to zero when the right conditions are
met, which is a huge improvement over the current situation
(where the doorbells are screaming if the CPU ever hits a
blocking WFI).
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Link: https://lore.kernel.org/r/20191107160412.30301-3-maz@kernel.org
In order to find out whether a vcpu is likely to be the target of
VLPIs (and to further optimize the way we deal with those), let's
track the number of VLPIs a vcpu can receive.
This gets implemented with an atomic variable that gets incremented
or decremented on map, unmap and move of a VLPI.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Link: https://lore.kernel.org/r/20191107160412.30301-2-maz@kernel.org
The timers are canceled from an preempt-notifier which is invoked with
disabled preemption which is not allowed on PREEMPT_RT.
The timer callback is short so in could be invoked in hard-IRQ context
on -RT.
Let the timer expire on hard-IRQ context even on -RT.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Julien Grall <julien.grall@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191107095424.16647-1-bigeasy@linutronix.de
The page table pages corresponding to broken down large pages are zapped in
FIFO order, so that the large page can potentially be recovered, if it is
not longer being used for execution. This removes the performance penalty
for walking deeper EPT page tables.
By default, one large page will last about one hour once the guest
reaches a steady state.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add a function to create a kernel thread associated with a given VM. In
particular, it ensures that the worker thread inherits the priority and
cgroups of the calling thread.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In kvm_create_vm(), if we've successfully called kvm_arch_init_vm(), but
then fail later in the function, we need to call kvm_arch_destroy_vm()
so that it can do any necessary cleanup (like freeing memory).
Fixes: 44a95dae1d ("KVM: x86: Detect and Initialize AVIC support")
Signed-off-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Junaid Shahid <junaids@google.com>
[Remove dependency on "kvm: Don't clear reference count on
kvm_create_vm() error path" which was not committed. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's possible that two LPIs locate in the same "byte_offset" but target
two different vcpus, where their pending status are indicated by two
different pending tables. In such a scenario, using last_byte_offset
optimization will lead KVM relying on the wrong pending table entry.
Let us use last_ptr instead, which can be treated as a byte index into
a pending table and also, can be vcpu specific.
Fixes: 280771252c ("KVM: arm64: vgic-v3: KVM_DEV_ARM_VGIC_SAVE_PENDING_TABLES")
Cc: stable@vger.kernel.org
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20191029071919.177-4-yuzenghui@huawei.com
Fix various comments, including wrong function names, grammar mistakes
and specification references.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191029071919.177-3-yuzenghui@huawei.com
When the VHE code was reworked, a lot of the vgic stuff was moved around,
but the GICv4 residency code did stay untouched, meaning that we come
in and out of residency on each flush/sync, which is obviously suboptimal.
To address this, let's move things around a bit:
- Residency entry (flush) moves to vcpu_load
- Residency exit (sync) moves to vcpu_put
- On blocking (entry to WFI), we "put"
- On unblocking (exit from WFI), we "load"
Because these can nest (load/block/put/load/unblock/put, for example),
we now have per-VPE tracking of the residency state.
Additionally, vgic_v4_put gains a "need doorbell" parameter, which only
gets set to true when blocking because of a WFI. This allows a finer
control of the doorbell, which now also gets disabled as soon as
it gets signaled.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20191027144234.8395-2-maz@kernel.org
This reorganization will allow us to call kvm_arch_destroy_vm in the
event that kvm_create_vm fails after calling kvm_arch_init_vm.
Suggested-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a new helper, kvm_put_kvm_no_destroy(), to handle putting a borrowed
reference[*] to the VM when installing a new file descriptor fails. KVM
expects the refcount to remain valid in this case, as the in-progress
ioctl() has an explicit reference to the VM. The primary motiviation
for the helper is to document that the 'kvm' pointer is still valid
after putting the borrowed reference, e.g. to document that doing
mutex(&kvm->lock) immediately after putting a ref to kvm isn't broken.
[*] When exposing a new object to userspace via a file descriptor, e.g.
a new vcpu, KVM grabs a reference to itself (the VM) prior to making
the object visible to userspace to avoid prematurely freeing the VM
in the scenario where userspace immediately closes file descriptor.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Special PMU edition:
- Fix cycle counter truncation
- Fix cycle counter overflow limit on pure 64bit system
- Allow chained events to be actually functional
- Correct sample period after overflow
-----BEGIN PGP SIGNATURE-----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=ORrS
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm fixes for 5.4, take #2
Special PMU edition:
- Fix cycle counter truncation
- Fix cycle counter overflow limit on pure 64bit system
- Allow chained events to be actually functional
- Correct sample period after overflow
Don't waste cycles to shrink/grow vCPU halt_poll_ns if host
side polling is disabled.
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow user space to inform the KVM host where in the physical memory
map the paravirtualized time structures should be located.
User space can set an attribute on the VCPU providing the IPA base
address of the stolen time structure for that VCPU. This must be
repeated for every VCPU in the VM.
The address is given in terms of the physical address visible to
the guest and must be 64 byte aligned. The guest will discover the
address via a hypercall.
Signed-off-by: Steven Price <steven.price@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Currently a kvm_device_ops structure cannot be const without triggering
compiler warnings. However the structure doesn't need to be written to
and, by marking it const, it can be read-only in memory. Add some more
const keywords to allow this.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Implement the service call for configuring a shared structure between a
VCPU and the hypervisor in which the hypervisor can write the time
stolen from the VCPU's execution time by other tasks on the host.
User space allocates memory which is placed at an IPA also chosen by user
space. The hypervisor then updates the shared structure using
kvm_put_guest() to ensure single copy atomicity of the 64-bit value
reporting the stolen time in nanoseconds.
Whenever stolen time is enabled by the guest, the stolen time counter is
reset.
The stolen time itself is retrieved from the sched_info structure
maintained by the Linux scheduler code. We enable SCHEDSTATS when
selecting KVM Kconfig to ensure this value is meaningful.
Signed-off-by: Steven Price <steven.price@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
This provides a mechanism for querying which paravirtualized time
features are available in this hypervisor.
Also add the header file which defines the ABI for the paravirtualized
time features we're about to add.
Signed-off-by: Steven Price <steven.price@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
We currently intertwine the KVM PSCI implementation with the general
dispatch of hypercall handling, which makes perfect sense because PSCI
is the only category of hypercalls we support.
However, as we are about to support additional hypercalls, factor out
this functionality into a separate hypercall handler file.
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
[steven.price@arm.com: rebased]
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
In some scenarios, such as buggy guest or incorrect configuration of the
VMM and firmware description data, userspace will detect a memory access
to a portion of the IPA, which is not mapped to any MMIO region.
For this purpose, the appropriate action is to inject an external abort
to the guest. The kernel already has functionality to inject an
external abort, but we need to wire up a signal from user space that
lets user space tell the kernel to do this.
It turns out, we already have the set event functionality which we can
perfectly reuse for this.
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
For a long time, if a guest accessed memory outside of a memslot using
any of the load/store instructions in the architecture which doesn't
supply decoding information in the ESR_EL2 (the ISV bit is not set), the
kernel would print the following message and terminate the VM as a
result of returning -ENOSYS to userspace:
load/store instruction decoding not implemented
The reason behind this message is that KVM assumes that all accesses
outside a memslot is an MMIO access which should be handled by
userspace, and we originally expected to eventually implement some sort
of decoding of load/store instructions where the ISV bit was not set.
However, it turns out that many of the instructions which don't provide
decoding information on abort are not safe to use for MMIO accesses, and
the remaining few that would potentially make sense to use on MMIO
accesses, such as those with register writeback, are not used in
practice. It also turns out that fetching an instruction from guest
memory can be a pretty horrible affair, involving stopping all CPUs on
SMP systems, handling multiple corner cases of address translation in
software, and more. It doesn't appear likely that we'll ever implement
this in the kernel.
What is much more common is that a user has misconfigured his/her guest
and is actually not accessing an MMIO region, but just hitting some
random hole in the IPA space. In this scenario, the error message above
is almost misleading and has led to a great deal of confusion over the
years.
It is, nevertheless, ABI to userspace, and we therefore need to
introduce a new capability that userspace explicitly enables to change
behavior.
This patch introduces KVM_CAP_ARM_NISV_TO_USER (NISV meaning Non-ISV)
which does exactly that, and introduces a new exit reason to report the
event to userspace. User space can then emulate an exception to the
guest, restart the guest, suspend the guest, or take any other
appropriate action as per the policy of the running system.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Alexander Graf <graf@amazon.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The PMU emulation code uses the perf event sample period to trigger
the overflow detection. This works fine for the *first* overflow
handling, but results in a huge number of interrupts on the host,
unrelated to the number of interrupts handled in the guest (a x20
factor is pretty common for the cycle counter). On a slow system
(such as a SW model), this can result in the guest only making
forward progress at a glacial pace.
It turns out that the clue is in the name. The sample period is
exactly that: a period. And once the an overflow has occured,
the following period should be the full width of the associated
counter, instead of whatever the guest had initially programed.
Reset the sample period to the architected value in the overflow
handler, which now results in a number of host interrupts that is
much closer to the number of interrupts in the guest.
Fixes: b02386eb7d ("arm64: KVM: Add PMU overflow interrupt routing")
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The current convention for KVM to request a chained event from the
host PMU is to set bit[0] in attr.config1 (PERF_ATTR_CFG1_KVM_PMU_CHAINED).
But as it turns out, this bit gets set *after* we create the kernel
event that backs our virtual counter, meaning that we never get
a 64bit counter.
Moving the setting to an earlier point solves the problem.
Fixes: 80f393a23b ("KVM: arm/arm64: Support chained PMU counters")
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
When a counter is disabled, its value is sampled before the event
is being disabled, and the value written back in the shadow register.
In that process, the value gets truncated to 32bit, which is adequate
for any counter but the cycle counter (defined as a 64bit counter).
This obviously results in a corrupted counter, and things like
"perf record -e cycles" not working at all when run in a guest...
A similar, but less critical bug exists in kvm_pmu_get_counter_value.
Make the truncation conditional on the counter not being the cycle
counter, which results in a minor code reorganisation.
Fixes: 80f393a23b ("KVM: arm/arm64: Support chained PMU counters")
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reported-by: Julien Thierry <julien.thierry.kdev@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
- Remove the now obsolete hyp_alternate_select construct
- Fix the TRACE_INCLUDE_PATH macro in the vgic code
-----BEGIN PGP SIGNATURE-----
iQJDBAABCgAtFiEEn9UcU+C1Yxj9lZw9I9DQutE9ekMFAl2TFyoPHG1hekBrZXJu
ZWwub3JnAAoJECPQ0LrRPXpDROwP/inRUonz+KEG2B0Bx/NWtzdnDghxdcoNC9H6
lVDHJ2dtC5Kmf0iHEualUvxXHYx7QJ3Maov3UAtkeYl3s4wC6TAl++QkqAG9PYsc
lPQH4GBiQNewQyaebc/NKHDz3I3TClJDq57haHSFFiCwsUpJRgYL8WjktZD/Dide
CUSQGxdnaALzHvMv5a8yQWadPL/RrXCZqOSKbUjjc20meZxrO66HwUd1G6uZZVDn
VClMQwFkQzVjR7yX21/7gmTcwG99RqVaAsvOpCu9+MVlqSpDROspmSPMuG5X/usO
zDgC07UFNPYHQKrGu8DHqlvO9DrK3vR8VEuKu+asVZP7D/ntvKhAM2c5ai188Z12
w8rOnhJKnDtMGHXn4owcC9tgSfrPR+ZukaltzKRVVFm1Y1Io+qTkAuf3geFqZ1hj
L9LWZ0KlMsFvfIKWPcAEp5rA9EeZoP5IeVCelBWj9ERDrcCMhma8RxpAlBPz1YPy
J345jthE4xFZYQxV+amTKJ3CzbZPuU2iIKgDBYiG2PNCuKwCT46RQitOXWWTwSIb
FZ6pcsmhofj69dSAlrRFjEpiLNkJuNX1ArsAA91vXemTXA2YfVLMZo1HkrmFNfbR
j4HP1BhNVdCgk6HF2HzwdRt8eutvk889GG3q+uCoYCaSu3M8MUEgx64LurOPProO
11jhNb3J
=9luB
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm fixes for 5.4, take #1
- Remove the now obsolete hyp_alternate_select construct
- Fix the TRACE_INCLUDE_PATH macro in the vgic code
The largepages debugfs entry is incremented/decremented as shadow
pages are created or destroyed. Clearing it will result in an
underflow, which is harmless to KVM but ugly (and could be
misinterpreted by tools that use debugfs information), so make
this particular statistic read-only.
Cc: kvm-ppc@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* ARM: ITS translation cache; support for 512 vCPUs, various cleanups
and bugfixes
* PPC: various minor fixes and preparation
* x86: bugfixes all over the place (posted interrupts, SVM, emulation
corner cases, blocked INIT), some IPI optimizations
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJdf7fdAAoJEL/70l94x66DJzkIAKDcuWXJB4Qtoto6yUvPiHZm
LYkY/Dn1zulb/DhzrBoXFey/jZXwl9kxMYkVTefnrAl0fRwFGX+G1UYnQrtAL6Gr
ifdTYdy3kZhXCnnp99QAantWDswJHo1THwbmHrlmkxS4MdisEaTHwgjaHrDRZ4/d
FAEwW2isSonP3YJfTtsKFFjL9k2D4iMnwZ/R2B7UOaWvgnerZ1GLmOkilvnzGGEV
IQ89IIkWlkKd4SKgq8RkDKlfW5JrLrSdTK2Uf0DvAxV+J0EFkEaR+WlLsqumra0z
Eg3KwNScfQj0DyT0TzurcOxObcQPoMNSFYXLRbUu1+i0CGgm90XpF1IosiuihgU=
=w6I3
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"s390:
- ioctl hardening
- selftests
ARM:
- ITS translation cache
- support for 512 vCPUs
- various cleanups and bugfixes
PPC:
- various minor fixes and preparation
x86:
- bugfixes all over the place (posted interrupts, SVM, emulation
corner cases, blocked INIT)
- some IPI optimizations"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (75 commits)
KVM: X86: Use IPI shorthands in kvm guest when support
KVM: x86: Fix INIT signal handling in various CPU states
KVM: VMX: Introduce exit reason for receiving INIT signal on guest-mode
KVM: VMX: Stop the preemption timer during vCPU reset
KVM: LAPIC: Micro optimize IPI latency
kvm: Nested KVM MMUs need PAE root too
KVM: x86: set ctxt->have_exception in x86_decode_insn()
KVM: x86: always stop emulation on page fault
KVM: nVMX: trace nested VM-Enter failures detected by H/W
KVM: nVMX: add tracepoint for failed nested VM-Enter
x86: KVM: svm: Fix a check in nested_svm_vmrun()
KVM: x86: Return to userspace with internal error on unexpected exit reason
KVM: x86: Add kvm_emulate_{rd,wr}msr() to consolidate VXM/SVM code
KVM: x86: Refactor up kvm_{g,s}et_msr() to simplify callers
doc: kvm: Fix return description of KVM_SET_MSRS
KVM: X86: Tune PLE Window tracepoint
KVM: VMX: Change ple_window type to unsigned int
KVM: X86: Remove tailing newline for tracepoints
KVM: X86: Trace vcpu_id for vmexit
KVM: x86: Manually calculate reserved bits when loading PDPTRS
...
The first/last indexes are typically shared with a user app.
The app can change the 'last' index that the kernel uses
to store the next result. This change sanity checks the index
before using it for writing to a potentially arbitrary address.
This fixes CVE-2019-14821.
Cc: stable@vger.kernel.org
Fixes: 5f94c1741b ("KVM: Add coalesced MMIO support (common part)")
Signed-off-by: Matt Delco <delco@chromium.org>
Signed-off-by: Jim Mattson <jmattson@google.com>
Reported-by: syzbot+983c866c3dd6efa3662a@syzkaller.appspotmail.com
[Use READ_ONCE. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 49dfe94fe5 ("KVM: arm/arm64: Fix TRACE_INCLUDE_PATH") fixes
TRACE_INCLUDE_PATH to the correct relative path to the define_trace.h
and explains why did the old one work.
The same fix should be applied to virt/kvm/arm/vgic/trace.h.
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
While parts of the VGIC support a large number of vcpus (we
bravely allow up to 512), other parts are more limited.
One of these limits is visible in the KVM_IRQ_LINE ioctl, which
only allows 256 vcpus to be signalled when using the CPU or PPI
types. Unfortunately, we've cornered ourselves badly by allocating
all the bits in the irq field.
Since the irq_type subfield (8 bit wide) is currently only taking
the values 0, 1 and 2 (and we have been careful not to allow anything
else), let's reduce this field to only 4 bits, and allocate the
remaining 4 bits to a vcpu2_index, which acts as a multiplier:
vcpu_id = 256 * vcpu2_index + vcpu_index
With that, and a new capability (KVM_CAP_ARM_IRQ_LINE_LAYOUT_2)
allowing this to be discovered, it becomes possible to inject
PPIs to up to 4096 vcpus. But please just don't.
Whilst we're there, add a clarification about the use of KVM_IRQ_LINE
on arm, which is not completely conditionned by KVM_CAP_IRQCHIP.
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
- Fix GICv2 emulation bug (KVM)
- Fix deadlock in virtual GIC interrupt injection code (KVM)
- Fix kprobes blacklist init failure due to broken kallsyms lookup
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl1mW/0ACgkQt6xw3ITB
YzQWEQgAnG+20c1uzPqIEME3o0bCXsci0I1w4yPYPH/NVrfmJdAjfway/cLZlMCh
JYKBTc392kfYXgzAvMqvjNe+9O/qg9MnMxV7Afjfk9e0k+41Kcw/7U39/B6q4yOg
zIz4YW6SdbbbUfY9VgR8SjsZ3HwJoP8YVNEv3W259funtFHkKDO35h1iG1f57GWL
UELjEnag9dmCH35ykt7+SC4woBGjOQnic2XLSS7VZuU/26TfnUyo2HCdDcLcViCZ
DHDQgaHAscb+tgJjeNtNEeRu+GPBG9LOhPw4EpBjGHeoJla7z74GOJPMEt4Ufoqd
qG9TPfOFAFM30/PAdlWF3SjfzqK3PA==
=WYzY
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Hot on the heels of our last set of fixes are a few more for -rc7.
Two of them are fixing issues with our virtual interrupt controller
implementation in KVM/arm, while the other is a longstanding but
straightforward kallsyms fix which was been acked by Masami and
resolves an initialisation failure in kprobes observed on arm64.
- Fix GICv2 emulation bug (KVM)
- Fix deadlock in virtual GIC interrupt injection code (KVM)
- Fix kprobes blacklist init failure due to broken kallsyms lookup"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
KVM: arm/arm64: vgic-v2: Handle SGI bits in GICD_I{S,C}PENDR0 as WI
KVM: arm/arm64: vgic: Fix potential deadlock when ap_list is long
kallsyms: Don't let kallsyms_lookup_size_offset() fail on retrieving the first symbol
A guest is not allowed to inject a SGI (or clear its pending state)
by writing to GICD_ISPENDR0 (resp. GICD_ICPENDR0), as these bits are
defined as WI (as per ARM IHI 0048B 4.3.7 and 4.3.8).
Make sure we correctly emulate the architecture.
Fixes: 96b298000d ("KVM: arm/arm64: vgic-new: Add PENDING registers handlers")
Cc: stable@vger.kernel.org # 4.7+
Reported-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
If the ap_list is longer than 256 entries, merge_final() in list_sort()
will call the comparison callback with the same element twice, causing
a deadlock in vgic_irq_cmp().
Fix it by returning early when irqa == irqb.
Cc: stable@vger.kernel.org # 4.7+
Fixes: 8e44474579 ("KVM: arm/arm64: vgic-new: Add IRQ sorting")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
[maz: massaged commit log and patch, added Fixes and Cc-stable]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
At the moment we use 2 IO devices per GICv3 redistributor: one
one for the RD_base frame and one for the SGI_base frame.
Instead we can use a single IO device per redistributor (the 2
frames are contiguous). This saves slots on the KVM_MMIO_BUS
which is currently limited to NR_IOBUS_DEVS (1000).
This change allows to instantiate up to 512 redistributors and may
speed the guest boot with a large number of VCPUs.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Detected by Coccinelle (and Will Deacon) using
scripts/coccinelle/misc/semicolon.cocci.
Reported-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
- Don't overskip instructions on MMIO emulation
- Fix UBSAN splat when initializing PPI priorities
-----BEGIN PGP SIGNATURE-----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=FGm5
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-for-5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm/fixes
Pull KVM/arm fixes from Marc Zyngier as per Paulo's request at:
https://lkml.kernel.org/r/21ae69a2-2546-29d0-bff6-2ea825e3d968@redhat.com
"One (hopefully last) set of fixes for KVM/arm for 5.3: an embarassing
MMIO emulation regression, and a UBSAN splat. Oh well...
- Don't overskip instructions on MMIO emulation
- Fix UBSAN splat when initializing PPI priorities"
* tag 'kvmarm-fixes-for-5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm:
KVM: arm/arm64: VGIC: Properly initialise private IRQ affinity
KVM: arm/arm64: Only skip MMIO insn once
At the moment we initialise the target *mask* of a virtual IRQ to the
VCPU it belongs to, even though this mask is only defined for GICv2 and
quickly runs out of bits for many GICv3 guests.
This behaviour triggers an UBSAN complaint for more than 32 VCPUs:
------
[ 5659.462377] UBSAN: Undefined behaviour in virt/kvm/arm/vgic/vgic-init.c:223:21
[ 5659.471689] shift exponent 32 is too large for 32-bit type 'unsigned int'
------
Also for GICv3 guests the reporting of TARGET in the "vgic-state" debugfs
dump is wrong, due to this very same problem.
Because there is no requirement to create the VGIC device before the
VCPUs (and QEMU actually does it the other way round), we can't safely
initialise mpidr or targets in kvm_vgic_vcpu_init(). But since we touch
every private IRQ for each VCPU anyway later (in vgic_init()), we can
just move the initialisation of those fields into there, where we
definitely know the VGIC type.
On the way make sure we really have either a VGICv2 or a VGICv3 device,
since the existing code is just checking for "VGICv3 or not", silently
ignoring the uninitialised case.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Dave Martin <dave.martin@arm.com>
Tested-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
If after an MMIO exit to userspace a VCPU is immediately run with an
immediate_exit request, such as when a signal is delivered or an MMIO
emulation completion is needed, then the VCPU completes the MMIO
emulation and immediately returns to userspace. As the exit_reason
does not get changed from KVM_EXIT_MMIO in these cases we have to
be careful not to complete the MMIO emulation again, when the VCPU is
eventually run again, because the emulation does an instruction skip
(and doing too many skips would be a waste of guest code :-) We need
to use additional VCPU state to track if the emulation is complete.
As luck would have it, we already have 'mmio_needed', which even
appears to be used in this way by other architectures already.
Fixes: 0d640732db ("arm64: KVM: Skip MMIO insn after emulation")
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
When a vpcu is about to block by calling kvm_vcpu_block, we call
back into the arch code to allow any form of synchronization that
may be required at this point (SVN stops the AVIC, ARM synchronises
the VMCR and enables GICv4 doorbells). But this synchronization
comes in quite late, as we've potentially waited for halt_poll_ns
to expire.
Instead, let's move kvm_arch_vcpu_blocking() to the beginning of
kvm_vcpu_block(), which on ARM has several benefits:
- VMCR gets synchronised early, meaning that any interrupt delivered
during the polling window will be evaluated with the correct guest
PMR
- GICv4 doorbells are enabled, which means that any guest interrupt
directly injected during that window will be immediately recognised
Tang Nianyao ran some tests on a GICv4 machine to evaluate such
change, and reported up to a 10% improvement for netperf:
<quote>
netperf result:
D06 as server, intel 8180 server as client
with change:
package 512 bytes - 5500 Mbits/s
package 64 bytes - 760 Mbits/s
without change:
package 512 bytes - 5000 Mbits/s
package 64 bytes - 710 Mbits/s
</quote>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Since commit 503a62862e ("KVM: arm/arm64: vgic: Rely on the GIC driver to
parse the firmware tables"), the vgic_v{2,3}_probe functions stopped using
a DT node. Commit 9097773245 ("KVM: arm/arm64: vgic-new: vgic_init:
implement kvm_vgic_hyp_init") changed the functions again, and now they
require exactly one argument, a struct gic_kvm_info populated by the GIC
driver. Unfortunately the comments regressed and state that a DT node is
used instead. Change the function comments to reflect the current
prototypes.
Signed-off-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Now that we have a cache of MSI->LPI translations, it is pretty
easy to implement kvm_arch_set_irq_inatomic (this cache can be
parsed without sleeping).
Hopefully, this will improve some LPI-heavy workloads.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
When performing an MSI injection, let's first check if the translation
is already in the cache. If so, let's inject it quickly without
going through the whole translation process.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
On a successful translation, preserve the parameters in the LPI
translation cache. Each translation is reusing the last slot
in the list, naturally evicting the least recently used entry.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
In order to avoid leaking vgic_irq structures on teardown, we need to
drop all references to LPIs before deallocating the cache itself.
This is done by invalidating the cache on vgic teardown.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
If an ITS gets disabled, we need to make sure that further interrupts
won't hit in the cache. For that, we invalidate the translation cache
when the ITS is disabled.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
If a vcpu disables LPIs at its redistributor level, we need to make sure
we won't pend more interrupts. For this, we need to invalidate the LPI
translation cache.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The LPI translation cache needs to be discarded when an ITS command
may affect the translation of an LPI (DISCARD, MAPC and MAPD with V=0)
or the routing of an LPI to a redistributor with disabled LPIs (MOVI,
MOVALL).
We decide to perform a full invalidation of the cache, irrespective
of the LPI that is affected. Commands are supposed to be rare enough
that it doesn't matter.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
There's a number of cases where we need to invalidate the caching
of translations, so let's add basic support for that.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Our LPI translation cache needs to be able to drop the refcount
on an LPI whilst already holding the lpi_list_lock.
Let's add a new primitive for this.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Add the basic data structure that expresses an MSI to LPI
translation as well as the allocation/release hooks.
The size of the cache is arbitrarily defined as 16*nr_vcpus.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
- Fix our system register reset so that we stop writing
non-sensical values to them, and track which registers
get reset instead.
- Sync VMCR back from the GIC on WFI so that KVM has an
exact vue of PMR.
- Reevaluate state of HW-mapped, level triggered interrupts
on enable.
-----BEGIN PGP SIGNATURE-----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=pZYJ
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-for-5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm fixes for 5.3, take #2
- Fix our system register reset so that we stop writing
non-sensical values to them, and track which registers
get reset instead.
- Sync VMCR back from the GIC on WFI so that KVM has an
exact vue of PMR.
- Reevaluate state of HW-mapped, level triggered interrupts
on enable.
The same check is already done in kvm_is_reserved_pfn.
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A HW mapped level sensitive interrupt asserted by a device will not be put
into the ap_list if it is disabled at the VGIC level. When it is enabled
again, it will be inserted into the ap_list and written to a list register
on guest entry regardless of the state of the device.
We could argue that this can also happen on real hardware, when the command
to enable the interrupt reached the GIC before the device had the chance to
de-assert the interrupt signal; however, we emulate the distributor and
redistributors in software and we can do better than that.
Signed-off-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Since commit commit 328e566479 ("KVM: arm/arm64: vgic: Defer
touching GICH_VMCR to vcpu_load/put"), we leave ICH_VMCR_EL2 (or
its GICv2 equivalent) loaded as long as we can, only syncing it
back when we're scheduled out.
There is a small snag with that though: kvm_vgic_vcpu_pending_irq(),
which is indirectly called from kvm_vcpu_check_block(), needs to
evaluate the guest's view of ICC_PMR_EL1. At the point were we
call kvm_vcpu_check_block(), the vcpu is still loaded, and whatever
changes to PMR is not visible in memory until we do a vcpu_put().
Things go really south if the guest does the following:
mov x0, #0 // or any small value masking interrupts
msr ICC_PMR_EL1, x0
[vcpu preempted, then rescheduled, VMCR sampled]
mov x0, #ff // allow all interrupts
msr ICC_PMR_EL1, x0
wfi // traps to EL2, so samping of VMCR
[interrupt arrives just after WFI]
Here, the hypervisor's view of PMR is zero, while the guest has enabled
its interrupts. kvm_vgic_vcpu_pending_irq() will then say that no
interrupts are pending (despite an interrupt being received) and we'll
block for no reason. If the guest doesn't have a periodic interrupt
firing once it has blocked, it will stay there forever.
To avoid this unfortuante situation, let's resync VMCR from
kvm_arch_vcpu_blocking(), ensuring that a following kvm_vcpu_check_block()
will observe the latest value of PMR.
This has been found by booting an arm64 Linux guest with the pseudo NMI
feature, and thus using interrupt priorities to mask interrupts instead
of the usual PSTATE masking.
Cc: stable@vger.kernel.org # 4.12
Fixes: 328e566479 ("KVM: arm/arm64: vgic: Defer touching GICH_VMCR to vcpu_load/put")
Signed-off-by: Marc Zyngier <maz@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Also, when doing this, change kvm_arch_create_vcpu_debugfs() to return
void instead of an integer, as we should not care at all about if this
function actually does anything or not.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <x86@kernel.org>
Cc: <kvm@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is no need for this function as all arches have to implement
kvm_arch_create_vcpu_debugfs() no matter what. A #define symbol
let us actually simplify the code.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After commit d73eb57b80 (KVM: Boost vCPUs that are delivering interrupts), a
five years old bug is exposed. Running ebizzy benchmark in three 80 vCPUs VMs
on one 80 pCPUs Skylake server, a lot of rcu_sched stall warning splatting
in the VMs after stress testing:
INFO: rcu_sched detected stalls on CPUs/tasks: { 4 41 57 62 77} (detected by 15, t=60004 jiffies, g=899, c=898, q=15073)
Call Trace:
flush_tlb_mm_range+0x68/0x140
tlb_flush_mmu.part.75+0x37/0xe0
tlb_finish_mmu+0x55/0x60
zap_page_range+0x142/0x190
SyS_madvise+0x3cd/0x9c0
system_call_fastpath+0x1c/0x21
swait_active() sustains to be true before finish_swait() is called in
kvm_vcpu_block(), voluntarily preempted vCPUs are taken into account
by kvm_vcpu_on_spin() loop greatly increases the probability condition
kvm_arch_vcpu_runnable(vcpu) is checked and can be true, when APICv
is enabled the yield-candidate vCPU's VMCS RVI field leaks(by
vmx_sync_pir_to_irr()) into spinning-on-a-taken-lock vCPU's current
VMCS.
This patch fixes it by checking conservatively a subset of events.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Marc Zyngier <Marc.Zyngier@arm.com>
Cc: stable@vger.kernel.org
Fixes: 98f4a1467 (KVM: add kvm_arch_vcpu_runnable() test to kvm_vcpu_on_spin() loop)
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
preempted_in_kernel is updated in preempt_notifier when involuntary preemption
ocurrs, it can be stale when the voluntarily preempted vCPUs are taken into
account by kvm_vcpu_on_spin() loop. This patch lets it just check preempted_in_kernel
for involuntary preemption.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When fall-through warnings was enabled by default the following warnings
was starting to show up:
../virt/kvm/arm/hyp/vgic-v3-sr.c: In function ‘__vgic_v3_save_aprs’:
../virt/kvm/arm/hyp/vgic-v3-sr.c:351:24: warning: this statement may fall
through [-Wimplicit-fallthrough=]
cpu_if->vgic_ap0r[2] = __vgic_v3_read_ap0rn(2);
~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~
../virt/kvm/arm/hyp/vgic-v3-sr.c:352:2: note: here
case 6:
^~~~
../virt/kvm/arm/hyp/vgic-v3-sr.c:353:24: warning: this statement may fall
through [-Wimplicit-fallthrough=]
cpu_if->vgic_ap0r[1] = __vgic_v3_read_ap0rn(1);
~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~
../virt/kvm/arm/hyp/vgic-v3-sr.c:354:2: note: here
default:
^~~~~~~
Rework so that the compiler doesn't warn about fall-through.
Fixes: d93512ef0f0e ("Makefile: Globally enable fall-through warning")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Renaming docs seems to be en vogue at the moment, so fix on of the
grossly misnamed directories. We usually never use "virtual" as
a shortcut for virtualization in the kernel, but always virt,
as seen in the virt/ top-level directory. Fix up the documentation
to match that.
Fixes: ed16648eb5 ("Move kvm, uml, and lguest subdirectories under a common "virtual" directory, I.E:")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We use "pmc->idx" and the "chained" bitmap to determine if the pmc is
chained, in kvm_pmu_pmc_is_chained(). But idx might be uninitialized
(and random) when we doing this decision, through a KVM_ARM_VCPU_INIT
ioctl -> kvm_pmu_vcpu_reset(). And the test_bit() against this random
idx will potentially hit a KASAN BUG [1].
In general, idx is the static property of a PMU counter that is not
expected to be modified across resets, as suggested by Julien. It
looks more reasonable if we can setup the PMU counter idx for a vcpu
in its creation time. Introduce a new function - kvm_pmu_vcpu_init()
for this basic setup. Oh, and the KASAN BUG will get fixed this way.
[1] https://www.spinics.net/lists/kvm-arm/msg36700.html
Fixes: 80f393a23b ("KVM: arm/arm64: Support chained PMU counters")
Suggested-by: Andrew Murray <andrew.murray@arm.com>
Suggested-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Inspired by commit 9cac38dd5d (KVM/s390: Set preempted flag during
vcpu wakeup and interrupt delivery), we want to also boost not just
lock holders but also vCPUs that are delivering interrupts. Most
smp_call_function_many calls are synchronous, so the IPI target vCPUs
are also good yield candidates. This patch introduces vcpu->ready to
boost vCPUs during wakeup and interrupt delivery time; unlike s390 we do
not reuse vcpu->preempted so that voluntarily preempted vCPUs are taken
into account by kvm_vcpu_on_spin, but vmx_vcpu_pi_put is not affected
(VT-d PI handles voluntary preemption separately, in pi_pre_block).
Testing on 80 HT 2 socket Xeon Skylake server, with 80 vCPUs VM 80GB RAM:
ebizzy -M
vanilla boosting improved
1VM 21443 23520 9%
2VM 2800 8000 180%
3VM 1800 3100 72%
Testing on my Haswell desktop 8 HT, with 8 vCPUs VM 8GB RAM, two VMs,
one running ebizzy -M, the other running 'stress --cpu 2':
w/ boosting + w/o pv sched yield(vanilla)
vanilla boosting improved
1570 4000 155%
w/ boosting + w/ pv sched yield(vanilla)
vanilla boosting improved
1844 5157 179%
w/o boosting, perf top in VM:
72.33% [kernel] [k] smp_call_function_many
4.22% [kernel] [k] call_function_i
3.71% [kernel] [k] async_page_fault
w/ boosting, perf top in VM:
38.43% [kernel] [k] smp_call_function_many
6.31% [kernel] [k] async_page_fault
6.13% libc-2.23.so [.] __memcpy_avx_unaligned
4.88% [kernel] [k] call_function_interrupt
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* support for chained PMU counters in guests
* improved SError handling
* handle Neoverse N1 erratum #1349291
* allow side-channel mitigation status to be migrated
* standardise most AArch64 system register accesses to msr_s/mrs_s
* fix host MPIDR corruption on 32bit
* selftests ckleanups
x86:
* PMU event {white,black}listing
* ability for the guest to disable host-side interrupt polling
* fixes for enlightened VMCS (Hyper-V pv nested virtualization),
* new hypercall to yield to IPI target
* support for passing cstate MSRs through to the guest
* lots of cleanups and optimizations
Generic:
* Some txt->rST conversions for the documentation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJdJzdIAAoJEL/70l94x66DQDoH/i83/8kX4I8AWDlushPru4ts
Q4lCE5VAPha+o4pLb1dtfFL3gTmSbsB1N++JSlqK3JOo6LphIOy6b0wBjQBbAa6U
3CT1dJaHJoScLLj09vyBlvClGUH2ZKEQTWOiquCCf7JfPofxwPUA6vJ7TYsdkckx
zR3ygbADWmnfS7hFfiqN3JzuYh9eoooGNWSU+Giq6VF41SiL3IqhBGZhWS0zE9c2
2c5lpqqdeHmAYNBqsyzNiDRKp7+zLFSmZ7Z5/0L755L8KYwR6F5beTnmBMHvb4lA
PWH/SWOC8EYR+PEowfrH+TxKZwp0gMn1kcAKjilHk0uCRwG1IzuHAr2jlNxICCk=
=t/Oq
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- support for chained PMU counters in guests
- improved SError handling
- handle Neoverse N1 erratum #1349291
- allow side-channel mitigation status to be migrated
- standardise most AArch64 system register accesses to msr_s/mrs_s
- fix host MPIDR corruption on 32bit
- selftests ckleanups
x86:
- PMU event {white,black}listing
- ability for the guest to disable host-side interrupt polling
- fixes for enlightened VMCS (Hyper-V pv nested virtualization),
- new hypercall to yield to IPI target
- support for passing cstate MSRs through to the guest
- lots of cleanups and optimizations
Generic:
- Some txt->rST conversions for the documentation"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (128 commits)
Documentation: virtual: Add toctree hooks
Documentation: kvm: Convert cpuid.txt to .rst
Documentation: virtual: Convert paravirt_ops.txt to .rst
KVM: x86: Unconditionally enable irqs in guest context
KVM: x86: PMU Event Filter
kvm: x86: Fix -Wmissing-prototypes warnings
KVM: Properly check if "page" is valid in kvm_vcpu_unmap
KVM: arm/arm64: Initialise host's MPIDRs by reading the actual register
KVM: LAPIC: Retry tune per-vCPU timer_advance_ns if adaptive tuning goes insane
kvm: LAPIC: write down valid APIC registers
KVM: arm64: Migrate _elx sysreg accessors to msr_s/mrs_s
KVM: doc: Add API documentation on the KVM_REG_ARM_WORKAROUNDS register
KVM: arm/arm64: Add save/restore support for firmware workaround state
arm64: KVM: Propagate full Spectre v2 workaround state to KVM guests
KVM: arm/arm64: Support chained PMU counters
KVM: arm/arm64: Remove pmc->bitmask
KVM: arm/arm64: Re-create event when setting counter value
KVM: arm/arm64: Extract duplicated code to own function
KVM: arm/arm64: Rename kvm_pmu_{enable/disable}_counter functions
KVM: LAPIC: ARBPRI is a reserved register for x2APIC
...
The PTE allocations in arm64 are identical to the generic ones modulo the
GFP flags.
Using the generic pte_alloc_one() functions ensures that the user page
tables are allocated with __GFP_ACCOUNT set.
The arm64 definition of PGALLOC_GFP is removed and replaced with
GFP_PGTABLE_USER for p[gum]d_alloc_one() for the user page tables and
GFP_PGTABLE_KERNEL for the kernel page tables. The KVM memory cache is now
using GFP_PGTABLE_USER.
The mappings created with create_pgd_mapping() are now using
GFP_PGTABLE_KERNEL.
The conversion to the generic version of pte_free_kernel() removes the NULL
check for pte.
The pte_free() version on arm64 is identical to the generic one and
can be simply dropped.
[cai@lca.pw: fix a bogus GFP flag in pgd_alloc()]
Link: https://lore.kernel.org/r/1559656836-24940-1-git-send-email-cai@lca.pw/
[and fix it more]
Link: https://lore.kernel.org/linux-mm/20190617151252.GF16810@rapoport-lnx/
Link: http://lkml.kernel.org/r/1557296232-15361-5-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Guo Ren <ren_guo@c-sky.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sam Creasey <sammy@sammy.net>
Cc: Vincent Chen <deanbo422@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Add support for chained PMU counters in guests
- Improve SError handling
- Handle Neoverse N1 erratum #1349291
- Allow side-channel mitigation status to be migrated
- Standardise most AArch64 system register accesses to msr_s/mrs_s
- Fix host MPIDR corruption on 32bit
-----BEGIN PGP SIGNATURE-----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=yfCs
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm updates for 5.3
- Add support for chained PMU counters in guests
- Improve SError handling
- Handle Neoverse N1 erratum #1349291
- Allow side-channel mitigation status to be migrated
- Standardise most AArch64 system register accesses to msr_s/mrs_s
- Fix host MPIDR corruption on 32bit
The field "page" is initialized to KVM_UNMAPPED_PAGE when it is not used
(i.e. when the memory lives outside kernel control). So this check will
always end up using kunmap even for memremap regions.
Fixes: e45adf665a ("KVM: Introduce a new guest mapping API")
Cc: stable@vger.kernel.org
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As part of setting up the host context, we populate its
MPIDR by using cpu_logical_map(). It turns out that contrary
to arm64, cpu_logical_map() on 32bit ARM doesn't return the
*full* MPIDR, but a truncated version.
This leaves the host MPIDR slightly corrupted after the first
run of a VM, since we won't correctly restore the MPIDR on
exit. Oops.
Since we cannot trust cpu_logical_map(), let's adopt a different
strategy. We move the initialization of the host CPU context as
part of the per-CPU initialization (which, in retrospect, makes
a lot of sense), and directly read the MPIDR from the HW. This
is guaranteed to work on both arm and arm64.
Reported-by: Andre Przywara <Andre.Przywara@arm.com>
Tested-by: Andre Przywara <Andre.Przywara@arm.com>
Fixes: 32f1395519 ("arm/arm64: KVM: Statically configure the host's view of MPIDR")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Paolo Bonzini