The NS for DAD are sent on admin up as long as a valid qdisc is found.
A race condition exists by which these packets will not egress the
interface if the operational state of the lower device is not yet up.
The solution is to delay DAD until the link is operationally up
according to RFC2863. Rather than only doing this, follow the existing
code checks by deferring IPv6 device initialization altogether. The fix
allows DAD on devices like tunnels that are controlled by userspace
control plane. The fix has no impact on regular deployments, but means
that there is no IPv6 connectivity until the port has been opened in
the case of port-based network access control, which should be
desirable.
Signed-off-by: Mike Manning <mmanning@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, writing into
net.ipv6.conf.all.{accept_dad,use_optimistic,optimistic_dad} has no effect.
Fix handling of these flags by:
- using the maximum of global and per-interface values for the
accept_dad flag. That is, if at least one of the two values is
non-zero, enable DAD on the interface. If at least one value is
set to 2, enable DAD and disable IPv6 operation on the interface if
MAC-based link-local address was found
- using the logical OR of global and per-interface values for the
optimistic_dad flag. If at least one of them is set to one, optimistic
duplicate address detection (RFC 4429) is enabled on the interface
- using the logical OR of global and per-interface values for the
use_optimistic flag. If at least one of them is set to one,
optimistic addresses won't be marked as deprecated during source address
selection on the interface.
While at it, as we're modifying the prototype for ipv6_use_optimistic_addr(),
drop inline, and let the compiler decide.
Fixes: 7fd2561e4e ("net: ipv6: Add a sysctl to make optimistic addresses useful candidates")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f784ad3d79 ("ipv6: do not send RTM_DELADDR for tentative
addresses") incorrectly assumes that no RTM_NEWADDR are sent for
addresses in tentative state, as this does happen for the standard
IPv6 use-case of DAD failure, see the call to ipv6_ifa_notify() in
addconf_dad_stop(). So as a result of this change, no RTM_DELADDR is
sent after DAD failure for a link-local when strict DAD (accept_dad=2)
is configured, or on the next admin down in other cases. The absence
of this notification breaks backwards compatibility and causes problems
after DAD failure if this notification was being relied on. The
solution is to allow RTM_DELADDR to still be sent after DAD failure.
Fixes: f784ad3d79 ("ipv6: do not send RTM_DELADDR for tentative addresses")
Signed-off-by: Mike Manning <mmanning@brocade.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c5cff8561d adds rcu grace period before freeing fib6_node. This
generates a new sparse warning on rt->rt6i_node related code:
net/ipv6/route.c:1394:30: error: incompatible types in comparison
expression (different address spaces)
./include/net/ip6_fib.h:187:14: error: incompatible types in comparison
expression (different address spaces)
This commit adds "__rcu" tag for rt6i_node and makes sure corresponding
rcu API is used for it.
After this fix, sparse no longer generates the above warning.
Fixes: c5cff8561d ("ipv6: add rcu grace period before freeing fib6_node")
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One nagging difference between ipv4 and ipv6 is host routes for ipv6
addresses are installed using the loopback device or VRF / L3 Master
device. e.g.,
2001:db8:1::/120 dev veth0 proto kernel metric 256 pref medium
local 2001:db8:1::1 dev lo table local proto kernel metric 0 pref medium
Using the loopback device is convenient -- necessary for local tx, but
has some nasty side effects, most notably setting the 'lo' device down
causes all host routes for all local IPv6 address to be removed from the
FIB and completely breaks IPv6 networking across all interfaces.
This patch puts FIB entries for IPv6 routes against the device. This
simplifies the routes in the FIB, for example by making dst->dev and
rt6i_idev->dev the same (a future patch can look at removing the device
reference taken for rt6i_idev for FIB entries).
When copies are made on FIB lookups, the cloned route has dst->dev
set to loopback (or the L3 master device). This is needed for the
local Tx of packets to local addresses.
With fib entries allocated against the real network device, the addrconf
code that reinserts host routes on admin up of 'lo' is no longer needed.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows us to later indicate to rtnetlink core that certain
doit functions should be called without acquiring rtnl_mutex.
This change should have no effect, we simply replace the last (now
unused) calcit argument with the new flag.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an interface is brought back up, the kernel tries to restore the
host routes tied to its permanent addresses.
However, if the host route was removed from the FIB, then we need to
reinsert it. This is done by releasing the current dst and allocating a
new, so as to not reuse a dst with obsolete values.
Since this function is called under RTNL and using the same explanation
from the previous patch, we can test if the route is in the FIB by
checking its node pointer instead of its reference count.
Tested using the following script and Andrey's reproducer mentioned
in commit 8048ced9be ("net: ipv6: regenerate host route if moved to gc
list") and linked below:
$ ip link set dev lo up
$ ip link add dummy1 type dummy
$ ip -6 address add cafe::1/64 dev dummy1
$ ip link set dev lo down # cafe::1/128 is removed
$ ip link set dev dummy1 up
$ ip link set dev lo up
The host route is correctly regenerated.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Link: http://lkml.kernel.org/r/CAAeHK+zSe82vc5gCRgr_EoUwiALPnWVdWJBPwJZBpbxYz=kGJw@mail.gmail.com
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the loopback device is brought back up we need to check if the host
route attached to the address is still in the FIB and regenerate one in
case it's not.
Host routes using the loopback device are always inserted into and
removed from the FIB under RTNL (under which this function is called),
so we can test their node pointer instead of the reference count in
order to check if the route is in the FIB or not.
Tested using the following script from Nicolas mentioned in
commit a220445f9f ("ipv6: correctly add local routes when lo goes up"):
$ ip link add dummy1 type dummy
$ ip link set dummy1 up
$ ip link set lo down ; ip link set lo up
The host route is correctly regenerated.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when the link for $DEV is down, this command succeeds but the
address is removed immediately by DAD (1):
ip addr add 1111::12/64 dev $DEV valid_lft 3600 preferred_lft 1800
In the same situation, this will succeed and not remove the address (2):
ip addr add 1111::12/64 dev $DEV
ip addr change 1111::12/64 dev $DEV valid_lft 3600 preferred_lft 1800
The comment in addrconf_dad_begin() when !IF_READY makes it look like
this is the intended behavior, but doesn't explain why:
* If the device is not ready:
* - keep it tentative if it is a permanent address.
* - otherwise, kill it.
We clearly cannot prevent userspace from doing (2), but we can make (1)
work consistently with (2).
addrconf_dad_stop() is only called in two cases: if DAD failed, or to
skip DAD when the link is down. In that second case, the fix is to avoid
deleting the address, like we already do for permanent addresses.
Fixes: 3c21edbd11 ("[IPV6]: Defer IPv6 device initialization until the link becomes ready.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The per netns loopback_dev->ip6_ptr is unregistered and set to
NULL when its mtu is set to smaller than IPV6_MIN_MTU, this
leads to that we could set rt->rt6i_idev NULL after a
rt6_uncached_list_flush_dev() and then crash after another
call.
In this case we should just bring its inet6_dev down, rather
than unregistering it, at least prior to commit 176c39af29
("netns: fix addrconf_ifdown kernel panic") we always
override the case for loopback.
Thanks a lot to Andrey for finding a reliable reproducer.
Fixes: 176c39af29 ("netns: fix addrconf_ifdown kernel panic")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two entries being added at the same time to the IFLA
policy table, whilst parallel bug fixes to decnet
routing dst handling overlapping with the dst gc removal
in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar as ipv4, ipv6 path also needs to call dst_hold_safe() when
necessary to avoid double free issue on the dst.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when starting the dad work in addrconf_mod_dad_work, if the dad work
is idle and queued, it needs to hold ifa.
The problem is there's one gap in [1], during which if the pending dad work
is removed elsewhere. It will miss to hold ifa, but the dad word is still
idea and queue.
if (!delayed_work_pending(&ifp->dad_work))
in6_ifa_hold(ifp);
<--------------[1]
mod_delayed_work(addrconf_wq, &ifp->dad_work, delay);
An use-after-free issue can be caused by this.
Chen Wei found this issue when WARN_ON(!hlist_unhashed(&ifp->addr_lst)) in
net6_ifa_finish_destroy was hit because of it.
As Hannes' suggestion, this patch is to fix it by holding ifa first in
addrconf_mod_dad_work, then calling mod_delayed_work and putting ifa if
the dad_work is already in queue.
Note that this patch did not choose to fix it with:
if (!mod_delayed_work(delay))
in6_ifa_hold(ifp);
As with it, when delay == 0, dad_work would be scheduled immediately, all
addrconf_mod_dad_work(0) callings had to be moved under ifp->lock.
Reported-by: Wei Chen <weichen@redhat.com>
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipvlan code already knows how to detect when a duplicate address is
about to be assigned to an ipvlan device. However, that failure is not
propogated outward and leads to a silent failure.
Introduce a validation step at ip address creation time and allow device
drivers to register to validate the incoming ip addresses. The ipvlan
code is the first consumer. If it detects an address in use, we can
return an error to the user before beginning to commit the new ifa in
the networking code.
This can be especially useful if it is necessary to provision many
ipvlans in containers. The provisioning software (or operator) can use
this to detect situations where an ip address is unexpectedly in use.
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every address gets added with TENTATIVE flag even for the addresses with
IFA_F_NODAD flag and dad-work is scheduled for them. During this DAD process
we realize it's an address with NODAD and complete the process without
sending any probe. However the TENTATIVE flags stays on the
address for sometime enough to cause misinterpretation when we receive a NS.
While processing NS, if the address has TENTATIVE flag, we mark it DADFAILED
and endup with an address that was originally configured as NODAD with
DADFAILED.
We can't avoid scheduling dad_work for addresses with NODAD but we can
avoid adding TENTATIVE flag to avoid this racy situation.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each netns (except init_net), we initialize its null entry
in 3 places:
1) The template itself, as we use kmemdup()
2) Code around dst_init_metrics() in ip6_route_net_init()
3) ip6_route_dev_notify(), which is supposed to initialize it after
loopback registers
Unfortunately the last one still happens in a wrong order because
we expect to initialize net->ipv6.ip6_null_entry->rt6i_idev to
net->loopback_dev's idev, thus we have to do that after we add
idev to loopback. However, this notifier has priority == 0 same as
ipv6_dev_notf, and ipv6_dev_notf is registered after
ip6_route_dev_notifier so it is called actually after
ip6_route_dev_notifier. This is similar to commit 2f460933f5
("ipv6: initialize route null entry in addrconf_init()") which
fixes init_net.
Fix it by picking a smaller priority for ip6_route_dev_notifier.
Also, we have to release the refcnt accordingly when unregistering
loopback_dev because device exit functions are called before subsys
exit functions.
Acked-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey reported a crash on init_net.ipv6.ip6_null_entry->rt6i_idev
since it is always NULL.
This is clearly wrong, we have code to initialize it to loopback_dev,
unfortunately the order is still not correct.
loopback_dev is registered very early during boot, we lose a chance
to re-initialize it in notifier. addrconf_init() is called after
ip6_route_init(), which means we have no chance to correct it.
Fix it by moving this initialization explicitly after
ipv6_add_dev(init_net.loopback_dev) in addrconf_init().
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey reported a warning triggered by the rcu code:
------------[ cut here ]------------
WARNING: CPU: 1 PID: 5911 at lib/debugobjects.c:289
debug_print_object+0x175/0x210
ODEBUG: activate active (active state 1) object type: rcu_head hint:
(null)
Modules linked in:
CPU: 1 PID: 5911 Comm: a.out Not tainted 4.11.0-rc8+ #271
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16
dump_stack+0x192/0x22d lib/dump_stack.c:52
__warn+0x19f/0x1e0 kernel/panic.c:549
warn_slowpath_fmt+0xe0/0x120 kernel/panic.c:564
debug_print_object+0x175/0x210 lib/debugobjects.c:286
debug_object_activate+0x574/0x7e0 lib/debugobjects.c:442
debug_rcu_head_queue kernel/rcu/rcu.h:75
__call_rcu.constprop.76+0xff/0x9c0 kernel/rcu/tree.c:3229
call_rcu_sched+0x12/0x20 kernel/rcu/tree.c:3288
rt6_rcu_free net/ipv6/ip6_fib.c:158
rt6_release+0x1ea/0x290 net/ipv6/ip6_fib.c:188
fib6_del_route net/ipv6/ip6_fib.c:1461
fib6_del+0xa42/0xdc0 net/ipv6/ip6_fib.c:1500
__ip6_del_rt+0x100/0x160 net/ipv6/route.c:2174
ip6_del_rt+0x140/0x1b0 net/ipv6/route.c:2187
__ipv6_ifa_notify+0x269/0x780 net/ipv6/addrconf.c:5520
addrconf_ifdown+0xe60/0x1a20 net/ipv6/addrconf.c:3672
...
Andrey's reproducer program runs in a very tight loop, calling
'unshare -n' and then spawning 2 sets of 14 threads running random ioctl
calls. The relevant networking sequence:
1. New network namespace created via unshare -n
- ip6tnl0 device is created in down state
2. address added to ip6tnl0
- equivalent to ip -6 addr add dev ip6tnl0 fd00::bb/1
- DAD is started on the address and when it completes the host
route is inserted into the FIB
3. ip6tnl0 is brought up
- the new fixup_permanent_addr function restarts DAD on the address
4. exit namespace
- teardown / cleanup sequence starts
- once in a blue moon, lo teardown appears to happen BEFORE teardown
of ip6tunl0
+ down on 'lo' removes the host route from the FIB since the dst->dev
for the route is loobback
+ host route added to rcu callback list
* rcu callback has not run yet, so rt is NOT on the gc list so it has
NOT been marked obsolete
5. in parallel to 4. worker_thread runs addrconf_dad_completed
- DAD on the address on ip6tnl0 completes
- calls ipv6_ifa_notify which inserts the host route
All of that happens very quickly. The result is that a host route that
has been deleted from the IPv6 FIB and added to the RCU list is re-inserted
into the FIB.
The exit namespace eventually gets to cleaning up ip6tnl0 which removes the
host route from the FIB again, calls the rcu function for cleanup -- and
triggers the double rcu trace.
The root cause is duplicate DAD on the address -- steps 2 and 3. Arguably,
DAD should not be started in step 2. The interface is in the down state,
so it can not really send out requests for the address which makes starting
DAD pointless.
Since the second DAD was introduced by a recent change, seems appropriate
to use it for the Fixes tag and have the fixup function only start DAD for
addresses in the PREDAD state which occurs in addrconf_ifdown if the
address is retained.
Big thanks to Andrey for isolating a reliable reproducer for this problem.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taking down the loopback device wreaks havoc on IPv6 routing. By
extension, taking down a VRF device wreaks havoc on its table.
Dmitry and Andrey both reported heap out-of-bounds reports in the IPv6
FIB code while running syzkaller fuzzer. The root cause is a dead dst
that is on the garbage list gets reinserted into the IPv6 FIB. While on
the gc (or perhaps when it gets added to the gc list) the dst->next is
set to an IPv4 dst. A subsequent walk of the ipv6 tables causes the
out-of-bounds access.
Andrey's reproducer was the key to getting to the bottom of this.
With IPv6, host routes for an address have the dst->dev set to the
loopback device. When the 'lo' device is taken down, rt6_ifdown initiates
a walk of the fib evicting routes with the 'lo' device which means all
host routes are removed. That process moves the dst which is attached to
an inet6_ifaddr to the gc list and marks it as dead.
The recent change to keep global IPv6 addresses added a new function,
fixup_permanent_addr, that is called on admin up. That function restarts
dad for an inet6_ifaddr and when it completes the host route attached
to it is inserted into the fib. Since the route was marked dead and
moved to the gc list, re-inserting the route causes the reported
out-of-bounds accesses. If the device with the address is taken down
or the address is removed, the WARN_ON in fib6_del is triggered.
All of those faults are fixed by regenerating the host route if the
existing one has been moved to the gc list, something that can be
determined by checking if the rt6i_ref counter is 0.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netlink_ext_ack arg to rtnl_doit_func. Pass extack arg to nlmsg_parse
for doit functions that call it directly.
This is the first step to using extended error reporting in rtnetlink.
>From here individual subsystems can be updated to set netlink_ext_ack as
needed.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2017-04-14
Here's the main batch of Bluetooth & 802.15.4 patches for the 4.12
kernel.
- Many fixes to 6LoWPAN, in particular for BLE
- New CA8210 IEEE 802.15.4 device driver (accounting for most of the
lines of code added in this pull request)
- Added Nokia Bluetooth (UART) HCI driver
- Some serdev & TTY changes that are dependencies for the Nokia
driver (with acks from relevant maintainers and an agreement that
these come through the bluetooth tree)
- Support for new Intel Bluetooth device
- Various other minor cleanups/fixes here and there
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were simply overlapping changes. In the net/ipv4/route.c
case the code had simply moved around a little bit and the same fix
was made in both 'net' and 'net-next'.
In the net/sched/sch_generic.c case a fix in 'net' happened at
the same time that a new argument was added to qdisc_hash_add().
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the new extended ACK reporting struct to all of the generic
netlink parsing functions. For now, pass NULL in almost all callers
(except for some in the core.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to RFC 7668 U/L bit shall not be used:
https://wiki.tools.ietf.org/html/rfc7668#section-3.2.2 [Page 10]:
In the figure, letter 'b' represents a bit from the
Bluetooth device address, copied as is without any changes on any
bit. This means that no bit in the IID indicates whether the
underlying Bluetooth device address is public or random.
|0 1|1 3|3 4|4 6|
|0 5|6 1|2 7|8 3|
+----------------+----------------+----------------+----------------+
|bbbbbbbbbbbbbbbb|bbbbbbbb11111111|11111110bbbbbbbb|bbbbbbbbbbbbbbbb|
+----------------+----------------+----------------+----------------+
Because of this the code cannot figure out the address type from the IP
address anymore thus it makes no sense to use peer_lookup_ba as it needs
the peer address type.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for 48 bit 6LoWPAN address length
autoconfiguration which is the case for BTLE 6LoWPAN.
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
addrconf_ifdown() removes elements from the idev->addr_list without
holding the idev->lock.
If this happens while the loop in __ipv6_dev_get_saddr() is handling the
same element, that function ends up in an infinite loop:
NMI watchdog: BUG: soft lockup - CPU#1 stuck for 23s! [test:1719]
Call Trace:
ipv6_get_saddr_eval+0x13c/0x3a0
__ipv6_dev_get_saddr+0xe4/0x1f0
ipv6_dev_get_saddr+0x1b4/0x204
ip6_dst_lookup_tail+0xcc/0x27c
ip6_dst_lookup_flow+0x38/0x80
udpv6_sendmsg+0x708/0xba8
sock_sendmsg+0x18/0x30
SyS_sendto+0xb8/0xf8
syscall_common+0x34/0x58
Fixes: 6a923934c3 (Revert "ipv6: Revert optional address flusing on ifdown.")
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send RTM_DELNETCONF notifications when a device is deleted. The message only
needs the device index, so modify inet6_netconf_fill_devconf to skip devconf
references if it is NULL.
Allows a userspace cache to remove entries as devices are deleted.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor inet6_netconf_notify_devconf to take the event as an input arg.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds a new sysctl accept_ra_rt_info_min_plen that
defines the minimum acceptable prefix length of Route Information
Options. The new sysctl is intended to be used together with
accept_ra_rt_info_max_plen to configure a range of acceptable
prefix lengths. It is useful to prevent misconfigurations from
unintentionally blackholing too much of the IPv6 address space
(e.g., home routers announcing RIOs for fc00::/7, which is
incorrect).
Signed-off-by: Joel Scherpelz <jscherpelz@google.com>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides equivalent functionality to the existing ipv4
"disable_policy" systcl. ie. Allows IPsec processing to be skipped
on terminating packets on a per-interface basis.
Signed-off-by: David Forster <dforster@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix double-free in batman-adv, from Sven Eckelmann.
2) Fix packet stats for fast-RX path, from Joannes Berg.
3) Netfilter's ip_route_me_harder() doesn't handle request sockets
properly, fix from Florian Westphal.
4) Fix sendmsg deadlock in rxrpc, from David Howells.
5) Add missing RCU locking to transport hashtable scan, from Xin Long.
6) Fix potential packet loss in mlxsw driver, from Ido Schimmel.
7) Fix race in NAPI handling between poll handlers and busy polling,
from Eric Dumazet.
8) TX path in vxlan and geneve need proper RCU locking, from Jakub
Kicinski.
9) SYN processing in DCCP and TCP need to disable BH, from Eric
Dumazet.
10) Properly handle net_enable_timestamp() being invoked from IRQ
context, also from Eric Dumazet.
11) Fix crash on device-tree systems in xgene driver, from Alban Bedel.
12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de
Melo.
13) Fix use-after-free in netvsc driver, from Dexuan Cui.
14) Fix max MTU setting in bonding driver, from WANG Cong.
15) xen-netback hash table can be allocated from softirq context, so use
GFP_ATOMIC. From Anoob Soman.
16) Fix MAC address change bug in bgmac driver, from Hari Vyas.
17) strparser needs to destroy strp_wq on module exit, from WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
strparser: destroy workqueue on module exit
sfc: fix IPID endianness in TSOv2
sfc: avoid max() in array size
rds: remove unnecessary returned value check
rxrpc: Fix potential NULL-pointer exception
nfp: correct DMA direction in XDP DMA sync
nfp: don't tell FW about the reserved buffer space
net: ethernet: bgmac: mac address change bug
net: ethernet: bgmac: init sequence bug
xen-netback: don't vfree() queues under spinlock
xen-netback: keep a local pointer for vif in backend_disconnect()
netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails
netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups
netfilter: nf_conntrack_sip: fix wrong memory initialisation
can: flexcan: fix typo in comment
can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer
can: gs_usb: fix coding style
can: gs_usb: Don't use stack memory for USB transfers
ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines
ixgbe: update the rss key on h/w, when ethtool ask for it
...
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The addr_gen_mode variable can be accessed by both sysctl and netlink.
Repleacd rtnl_lock() with rtnl_trylock() protect the sysctl operation to
avoid the possbile dead lock.`
Signed-off-by: Felix Jia <felix.jia@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under some circumstances it is possible that no new temporary addresses
will be generated.
For instance, addrconf_prefix_rcv_add_addr() indirectly calls
ipv6_create_tempaddr(), which creates a tentative temporary address and
starts dad. Next, addrconf_prefix_rcv_add_addr() indirectly calls
addrconf_verify_rtnl(). Now, assume that the previously created temporary
address has the least preferred lifetime among all existing addresses and
is still tentative (that is, dad is still running). Hence, the next run of
addrconf_verify_rtnl() is performed when the preferred lifetime of the
temporary address ends. If dad succeeds before the next run, the temporary
address becomes deprecated during the next run, but no new temporary
address is generated.
In order to fix this, schedule the next addrconf_verify_rtnl() run slightly
before the temporary address becomes deprecated, if dad succeeded.
Signed-off-by: Marcus Huewe <suse-tux@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conflict was an interaction between a bug fix in the
netvsc driver in 'net' and an optimization of the RX path
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
When for instance a mobile Linux device roams from one access point to
another with both APs sharing the same broadcast domain and a
multicast snooping switch in between:
1) (c) <~~~> (AP1) <--[SSW]--> (AP2)
2) (AP1) <--[SSW]--> (AP2) <~~~> (c)
Then currently IPv6 multicast packets will get lost for (c) until an
MLD Querier sends its next query message. The packet loss occurs
because upon roaming the Linux host so far stayed silent regarding
MLD and the snooping switch will therefore be unaware of the
multicast topology change for a while.
This patch fixes this by always resending MLD reports when an interface
change happens, for instance from NO-CARRIER to CARRIER state.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address generation mode for IPv6 link-local can only be configured
by netlink messages. This patch adds the ability to change the address
generation mode via sysctl.
v1 -> v2
Removed the rtnl lock and switch to use RCU lock to iterate through
the netdev list.
v2 -> v3
Removed the addrgenmode variable from the idev structure and use the
systcl storage for the flag.
Simplifed the logic for sysctl handling by removing the supported
for all operation.
Added support for more types of tunnel interfaces for link-local
address generation.
Based the patches from net-next.
v3 -> v4
Removed unnecessary whitespace changes.
Signed-off-by: Felix Jia <felix.jia@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like commit 4acd4945cd ("ipv6: addrconf: Avoid calling
netdevice notifiers with RCU read-side lock"), it is unnecessary
to make addrconf_disable_change() use RCU iteration over the
netdev list, since it already holds the RTNL lock, or we may meet
Illegal context switch in RCU read-side critical section.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTM_NEWADDR notification is sent when IFA_F_TENTATIVE is cleared from
the address. So if the address is added and deleted before DAD probes
completes, the RTM_DELADDR will be sent for which there was no
RTM_NEWADDR causing asymmetry in notification. However if the same
logic is used while sending RTM_DELADDR notification, this asymmetry
can be avoided.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Patrick McHardy <kaber@trash.net>
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemented RFC7527 Enhanced DAD.
IPv6 duplicate address detection can fail if there is some temporary
loopback of Ethernet frames. RFC7527 solves this by including a random
nonce in the NS messages used for DAD, and if an NS is received with the
same nonce it is assumed to be a looped back DAD probe and is ignored.
RFC7527 is enabled by default. Can be disabled by setting both of
conf/{all,interface}/enhanced_dad to zero.
Signed-off-by: Erik Nordmark <nordmark@arista.com>
Signed-off-by: Bob Gilligan <gilligan@arista.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When an ipv6 address has the tentative flag set, it can't be
used as source for egress traffic, while the associated route,
if any, can be looked up and even stored into some dst_cache.
In the latter scenario, the source ipv6 address selected and
stored in the cache is most probably wrong (e.g. with
link-local scope) and the entity using the dst_cache will
experience lack of ipv6 connectivity until said cache is
cleared or invalidated.
Overall this may cause lack of connectivity over most IPv6 tunnels
(comprising geneve and vxlan), if the first egress packet reaches
the tunnel before the DaD is completed for the used ipv6
address.
This patch bumps a new genid after that the IFA_F_TENTATIVE flag
is cleared, so that dst_cache will be invalidated on
next lookup and ipv6 connectivity restored.
Fixes: 0c1d70af92 ("net: use dst_cache for vxlan device")
Fixes: 468dfffcd7 ("geneve: add dst caching support")
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the necessary functions to compute and check the HMAC signature
of an SR-enabled packet. Two HMAC algorithms are supported: hmac(sha1) and
hmac(sha256).
In order to avoid dynamic memory allocation for each HMAC computation,
a per-cpu ring buffer is allocated for this purpose.
A new per-interface sysctl called seg6_require_hmac is added, allowing a
user-defined policy for processing HMAC-signed SR-enabled packets.
A value of -1 means that the HMAC field will always be ignored.
A value of 0 means that if an HMAC field is present, its validity will
be enforced (the packet is dropped is the signature is incorrect).
Finally, a value of 1 means that any SR-enabled packet that does not
contain an HMAC signature or whose signature is incorrect will be dropped.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement minimal support for processing of SR-enabled packets
as described in
https://tools.ietf.org/html/draft-ietf-6man-segment-routing-header-02.
This patch implements the following operations:
- Intermediate segment endpoint: incrementation of active segment and rerouting.
- Egress for SR-encapsulated packets: decapsulation of outer IPv6 header + SRH
and routing of inner packet.
- Cleanup flag support for SR-inlined packets: removal of SRH if we are the
penultimate segment endpoint.
A per-interface sysctl seg6_enabled is provided, to accept/deny SR-enabled
packets. Default is deny.
This patch does not provide support for HMAC-signed packets.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for an underflow of tmp_prefered_lft is always false
because tmp_prefered_lft is unsigned. The intention of the check
was to guard against racing with an update of the
temp_prefered_lft sysctl, potentially resulting in an underflow.
As suggested by David Miller, the best way to prevent the race is
by reading the sysctl variable using READ_ONCE.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Fixes: 76506a986d ("IPv6: fix DESYNC_FACTOR")
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv6 temporary address generation uses a variable called DESYNC_FACTOR
to prevent hosts updating the addresses at the same time. Quoting RFC 4941:
... The value DESYNC_FACTOR is a random value (different for each
client) that ensures that clients don't synchronize with each other and
generate new addresses at exactly the same time ...
DESYNC_FACTOR is defined as:
DESYNC_FACTOR -- A random value within the range 0 - MAX_DESYNC_FACTOR.
It is computed once at system start (rather than each time it is used)
and must never be greater than (TEMP_VALID_LIFETIME - REGEN_ADVANCE).
First, I believe the RFC has a typo in it and meant to say: "and must
never be greater than (TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE)"
The reason is that at various places in the RFC, DESYNC_FACTOR is used in
a calculation like (TEMP_PREFERRED_LIFETIME - DESYNC_FACTOR) or
(TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE - DESYNC_FACTOR). It needs to be
smaller than (TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE) for the result of
these calculations to be larger than zero. It's never used in a
calculation together with TEMP_VALID_LIFETIME.
I already submitted an errata to the rfc-editor:
https://www.rfc-editor.org/errata_search.php?rfc=4941
The Linux implementation of DESYNC_FACTOR is very wrong:
max_desync_factor is used in places DESYNC_FACTOR should be used.
max_desync_factor is initialized to the RFC-recommended value for
MAX_DESYNC_FACTOR (600) but the whole point is to get a _random_ value.
And nothing ensures that the value used is not greater than
(TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE), which leads to underflows. The
effect can easily be observed when setting the temp_prefered_lft sysctl
e.g. to 60. The preferred lifetime of the temporary addresses will be
bogus.
TEMP_PREFERRED_LIFETIME and REGEN_ADVANCE are not constants and can be
influenced by these three sysctls: regen_max_retry, dad_transmits and
temp_prefered_lft. Thus, the upper bound for desync_factor needs to be
re-calculated each time a new address is generated and if desync_factor is
larger than the new upper bound, a new random value needs to be
re-generated.
And since we already have max_desync_factor configurable per interface, we
also need to calculate and store desync_factor per interface.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The randomized interface identifier (rndid) was periodically updated from
the regen_timer timer. Simplify the code by updating the rndid only when
needed by ipv6_try_regen_rndid().
This makes the follow-up DESYNC_FACTOR fix much simpler. Also it fixes a
reference counting error in this error path, where an in6_dev_put was
missing:
err = addrconf_sysctl_register(ndev);
if (err) {
ipv6_mc_destroy_dev(ndev);
- del_timer(&ndev->regen_timer);
snmp6_unregister_dev(ndev);
goto err_release;
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of the patch is to fix this scenario:
ip link add dummy1 type dummy
ip link set dummy1 up
ip link set lo down ; ip link set lo up
After that sequence, the local route to the link layer address of dummy1 is
not there anymore.
When the loopback is set down, all local routes are deleted by
addrconf_ifdown()/rt6_ifdown(). At this time, the rt6_info entry still
exists, because the corresponding idev has a reference on it. After the rcu
grace period, dst_rcu_free() is called, and thus ___dst_free(), which will
set obsolete to DST_OBSOLETE_DEAD.
In this case, init_loopback() is called before dst_rcu_free(), thus
obsolete is still sets to something <= 0. So, the function doesn't add the
route again. To avoid that race, let's check the rt6 refcnt instead.
Fixes: 25fb6ca4ed ("net IPv6 : Fix broken IPv6 routing table after loopback down-up")
Fixes: a881ae1f62 ("ipv6: don't call addrconf_dst_alloc again when enable lo")
Fixes: 33d99113b1 ("ipv6: reallocate addrconf router for ipv6 address when lo device up")
Reported-by: Francesco Santoro <francesco.santoro@6wind.com>
Reported-by: Samuel Gauthier <samuel.gauthier@6wind.com>
CC: Balakumaran Kannan <Balakumaran.Kannan@ap.sony.com>
CC: Maruthi Thotad <Maruthi.Thotad@ap.sony.com>
CC: Sabrina Dubroca <sd@queasysnail.net>
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
CC: Weilong Chen <chenweilong@huawei.com>
CC: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This disallows setting /proc/sys/net/ipv6/conf/*/router_solicitations
to values below -1.
-1 continues to mean an unlimited number of retransmits.
Note: this depends on 'ipv6 addrconf: remove addrconf_sysctl_hop_limit()'
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an effective no-op in terms of user observable behaviour.
By preventing the overwrite of non-null extra1/extra2 fields
in addrconf_sysctl() we can enable the use of proc_dointvec_minmax().
This allows us to eliminate the constant min/max (1..255) trampoline
function that is addrconf_sysctl_hop_limit().
This is nice because it simplifies the code, and allows future
sysctls with constant min/max limits to also not require trampolines.
We still can't eliminate the trampoline for mtu because it isn't
actually a constant (it depends on other tunables of the device)
and thus requires at-write-time logic to enforce range.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Erik Kline <ek@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements:
https://tools.ietf.org/html/rfc7559
Backoff is performed according to RFC3315 section 14:
https://tools.ietf.org/html/rfc3315#section-14
We allow setting /proc/sys/net/ipv6/conf/*/router_solicitations
to a negative value meaning an unlimited number of retransmits,
and we make this the new default (inline with the RFC).
We also add a new setting:
/proc/sys/net/ipv6/conf/*/router_solicitation_max_interval
defaulting to 1 hour (per RFC recommendation).
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Erik Kline <ek@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parameter items(is always ICMP6_MIB_MAX) is useless for __snmp6_fill_statsdev
Signed-off-by: Jia He <hejianet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In general, when DAD detected IPv6 duplicate address, ifp->state
will be set to INET6_IFADDR_STATE_ERRDAD and DAD is stopped by a
delayed work, the call tree should be like this:
ndisc_recv_ns
-> addrconf_dad_failure <- missing ifp put
-> addrconf_mod_dad_work
-> schedule addrconf_dad_work()
-> addrconf_dad_stop() <- missing ifp hold before call it
addrconf_dad_failure() called with ifp refcont holding but not put.
addrconf_dad_work() call addrconf_dad_stop() without extra holding
refcount. This will not cause any issue normally.
But the race between addrconf_dad_failure() and addrconf_dad_work()
may cause ifp refcount leak and netdevice can not be unregister,
dmesg show the following messages:
IPv6: eth0: IPv6 duplicate address fe80::XX:XXXX:XXXX:XX detected!
...
unregister_netdevice: waiting for eth0 to become free. Usage count = 1
Cc: stable@vger.kernel.org
Fixes: c15b1ccadb ("ipv6: move DAD and addrconf_verify processing
to workqueue")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All changes are notified, but the initial state was missing.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'default' value was not advertised.
Fixes: f3a1bfb11c ("rtnl/ipv6: use netconf msg to advertise forwarding status")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If DAD fails with accept_dad set to 2, global addresses and host routes
are incorrectly left in place. Even though disable_ipv6 is set,
contrary to documentation, the addresses are not dynamically deleted
from the interface. It is only on a subsequent link down/up that these
are removed. The fix is not only to set the disable_ipv6 flag, but
also to call addrconf_ifdown(), which is the action to carry out when
disabling IPv6. This results in the addresses and routes being deleted
immediately. The DAD failure for the LL addr is determined as before
via netlink, or by the absence of the LL addr (which also previously
would have had to be checked for in case of an intervening link down
and up). As the call to addrconf_ifdown() requires an rtnl lock, the
logic to disable IPv6 when DAD fails is moved to addrconf_dad_work().
Previous behavior:
root@vm1:/# sysctl net.ipv6.conf.eth3.accept_dad=2
net.ipv6.conf.eth3.accept_dad = 2
root@vm1:/# ip -6 addr add 2000::10/64 dev eth3
root@vm1:/# ip link set up eth3
root@vm1:/# ip -6 addr show dev eth3
5: eth3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
inet6 2000::10/64 scope global
valid_lft forever preferred_lft forever
inet6 fe80::5054:ff:fe43:dd5a/64 scope link tentative dadfailed
valid_lft forever preferred_lft forever
root@vm1:/# ip -6 route show dev eth3
2000::/64 proto kernel metric 256
fe80::/64 proto kernel metric 256
root@vm1:/# ip link set down eth3
root@vm1:/# ip link set up eth3
root@vm1:/# ip -6 addr show dev eth3
root@vm1:/# ip -6 route show dev eth3
root@vm1:/#
New behavior:
root@vm1:/# sysctl net.ipv6.conf.eth3.accept_dad=2
net.ipv6.conf.eth3.accept_dad = 2
root@vm1:/# ip -6 addr add 2000::10/64 dev eth3
root@vm1:/# ip link set up eth3
root@vm1:/# ip -6 addr show dev eth3
root@vm1:/# ip -6 route show dev eth3
root@vm1:/#
Signed-off-by: Mike Manning <mmanning@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If IPv6 is disabled when the option is set to keep IPv6
addresses on link down, userspace is unaware of this as
there is no such indication via netlink. The solution is to
remove the IPv6 addresses in this case, which results in
netlink messages indicating removal of addresses in the
usual manner. This fix also makes the behavior consistent
with the case of having IPv6 disabled first, which stops
IPv6 addresses from being added.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Signed-off-by: Mike Manning <mmanning@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using list_move() instead of list_del() + list_add().
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default kernel behavior is to delete IPv6 addresses on link
down, which entails deletion of the multicast and the
subnet-router anycast addresses. These deletions do not
happen with sysctl setting to keep global IPv6 addresses on
link down, so every link down/up causes an increment of the
anycast and multicast refcounts. These bogus refcounts may
stop these addrs from being removed on subsequent calls to
delete them. The solution is to leave the groups for the
multicast and subnet anycast on link down for the callflow
when global IPv6 addresses are kept.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Signed-off-by: Mike Manning <mmanning@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All inet6_netconf_notify_devconf() callers are in process context,
so we can use GFP_KERNEL allocations if we take care of not holding
a rwlock while not needed in ip6mr (we hold RTNL there)
Fixes: d67b8c616b ("netconf: advertise mc_forwarding status")
Fixes: f3a1bfb11c ("rtnl/ipv6: use netconf msg to advertise forwarding status")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 version of 3f2fb9a834 ("net: l3mdev: address selection should only
consider devices in L3 domain") and the follow up commit, a17b693cdd876
("net: l3mdev: prefer VRF master for source address selection").
That is, if outbound device is given then the address preference order
is an address from that device, an address from the master device if it
is enslaved, and then an address from a device in the same L3 domain.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exports some neighbour discovery functions which can be used
by 6lowpan neighbour discovery ops functionality then.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces neighbour discovery ops callback structure. The
idea is to separate the handling for 6LoWPAN into the 6lowpan module.
These callback offers 6lowpan different handling, such as 802.15.4 short
address handling or RFC6775 (Neighbor Discovery Optimization for IPv6
over 6LoWPANs).
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the functionality to add a RA PIO prefix generated
address in an own function. This move prepares to add a hook for
adding a second address for a second link-layer address. E.g. short
address for 802.15.4 6LoWPAN.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the autoconfiguration if a valid 802.15.4 short address
is available for 802.15.4 6LoWPAN interfaces.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
L3 master devices are virtual devices similar to the loopback
device. Link local and multicast routes for these devices do
not make sense. The ipv6 addrconf code already skips adding a
linklocal address; do the same for the mcast route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in the conflicts.
In the macsec case, the change of the default ID macro
name overlapped with the 64-bit netlink attribute alignment
fixes in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
It was a simple idea -- save IPv6 configured addresses on a link down
so that IPv6 behaves similar to IPv4. As always the devil is in the
details and the IPv6 stack as too many behavioral differences from IPv4
making the simple idea more complicated than it needs to be.
The current implementation for keeping IPv6 addresses can panic or spit
out a warning in one of many paths:
1. IPv6 route gets an IPv4 route as its 'next' which causes a panic in
rt6_fill_node while handling a route dump request.
2. rt->dst.obsolete is set to DST_OBSOLETE_DEAD hitting the WARN_ON in
fib6_del
3. Panic in fib6_purge_rt because rt6i_ref count is not 1.
The root cause of all these is references related to the host route for
an address that is retained.
So, this patch deletes the host route every time the ifdown loop runs.
Since the host route is deleted and will be re-generated an up there is
no longer a need for the l3mdev fix up. On the 'admin up' side move
addrconf_permanent_addr into the NETDEV_UP event handling so that it
runs only once versus on UP and CHANGE events.
All of the current panics and warnings appear to be related to
addresses on the loopback device, but given the catastrophic nature when
a bug is triggered this patch takes the conservative approach and evicts
all host routes rather than trying to determine when it can be re-used
and when it can not. That can be a later optimizaton if desired.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 841645b5f2.
Ok, this puts the feature back. I've decided to apply David A.'s
bug fix and run with that rather than make everyone wait another
whole release for this feature.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts the following three commits:
70af921db6799977d9aaf1705ec197
The feature was ill conceived, has terrible semantics, and has added
nothing but regressions to the already fragile ipv6 stack.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were two cases of simple overlapping changes,
nothing serious.
In the UDP case, we need to add a hlist_add_tail_rcu()
to linux/rculist.h, because we've moved UDP socket handling
away from using nulls lists.
Signed-off-by: David S. Miller <davem@davemloft.net>
Separated from previous patch for readability.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Struct ctl_table_header holds pointer to sysctl table which could be used
for freeing it after unregistration. IPv4 sysctls already use that.
Remove redundant NULL assignment: ndev allocated using kzalloc.
This also saves some bytes: sysctl table could be shorter than
DEVCONF_MAX+1 if some options are disable in config.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
f1705ec197 added the option to retain user configured addresses on an
admin down. A comment to one of the later revisions suggested using the
IFA_F_PERMANENT flag rather than adding a user_managed boolean to the
ifaddr struct. A side effect of this change is that link local and
loopback addresses are also retained which is not part of the objective
of f1705ec197. Add check to drop those addresses.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original tokenized iid support implemented via f53adae4ea ("net: ipv6:
add tokenized interface identifier support") didn't allow for clearing a
device token as it was intended that this addressing mode was the only one
active for globally scoped IPv6 addresses. Later we relaxed that restriction
via 617fe29d45 ("net: ipv6: only invalidate previously tokenized addresses"),
and we should also allow for clearing tokens as there's no good reason why
it shouldn't be allowed.
Fixes: 617fe29d45 ("net: ipv6: only invalidate previously tokenized addresses")
Reported-by: Robin H. Johnson <robbat2@gentoo.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ifupdown2 found a kernel bug with IPv6 routes and movement from the main
table to the VRF table. Sequence of events:
Create the interface and add addresses:
ip link add dev eth4.105 link eth4 type vlan id 105
ip addr add dev eth4.105 8.105.105.10/24
ip -6 addr add dev eth4.105 2008:105:105::10/64
At this point IPv6 has inserted a prefix route in the main table even
though the interface is 'down'. From there the VRF device is created:
ip link add dev vrf105 type vrf table 105
ip addr add dev vrf105 9.9.105.10/32
ip -6 addr add dev vrf105 2000:9:105::10/128
ip link set vrf105 up
Then the interface is enslaved, while still in the 'down' state:
ip link set dev eth4.105 master vrf105
Since the device is down the VRF driver cycling the device does not
send the NETDEV_UP and NETDEV_DOWN but rather the NETDEV_CHANGE event
which does not flush the routes inserted prior.
When the link is brought up
ip link set dev eth4.105 up
the prefix route is added in the VRF table, but does not remove
the route from the main table.
Fix by handling the NETDEV_CHANGEUPPER event similar what was implemented
for IPv4 in 7f49e7a38b ("net: Flush local routes when device changes vrf
association")
Fixes: 35402e3136 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds macro NETCONFA_ALL to represent all type of netconf
attributes for IPv4 and IPv6.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew and Ying Huang's test robot both reported usage count problems that
trace back to the 'keep address on ifdown' patch.
>From Andrew:
We execute CRIU test on linux-next. On the current linux-next kernel
they hangs on creating a network namespace.
The kernel log contains many massages like this:
[ 1036.122108] unregister_netdevice: waiting for lo to become free.
Usage count = 2
[ 1046.165156] unregister_netdevice: waiting for lo to become free.
Usage count = 2
[ 1056.210287] unregister_netdevice: waiting for lo to become free.
Usage count = 2
I tried to revert this patch and the bug disappeared.
Here is a set of commands to reproduce this bug:
[root@linux-next-test linux-next]# uname -a
Linux linux-next-test 4.5.0-rc6-next-20160301+ #3 SMP Wed Mar 2
17:32:18 UTC 2016 x86_64 x86_64 x86_64 GNU/Linux
[root@linux-next-test ~]# unshare -n
[root@linux-next-test ~]# ip link set up dev lo
[root@linux-next-test ~]# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
group default qlen 1
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
[root@linux-next-test ~]# logout
[root@linux-next-test ~]# unshare -n
-----
The problem is a change made to RTM_DELADDR case in __ipv6_ifa_notify that
was added in an early version of the offending patch and is no longer
needed.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Cc: Andrey Wagin <avagin@gmail.com>
Cc: Ying Huang <ying.huang@linux.intel.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f1705ec197 allows IPv6 addresses to be retained on a link down.
The address can have a cached host route which can point to the wrong
FIB table if the L3 enslavement is changed (e.g., route can point to local
table instead of VRF table if device is added to an L3 domain).
On link up check the table of the cached host route against the FIB
table associated with the device and correct if needed.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, all ipv6 addresses are flushed when the interface is configured
down, including global, static addresses:
$ ip -6 addr show dev eth1
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 state UP qlen 1000
inet6 2100:1::2/120 scope global
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe79:34bd/64 scope link
valid_lft forever preferred_lft forever
$ ip link set dev eth1 down
$ ip -6 addr show dev eth1
<< nothing; all addresses have been flushed>>
Add a new sysctl to make this behavior optional. The new setting defaults to
flush all addresses to maintain backwards compatibility. When the set global
addresses with no expire times are not flushed on an admin down. The sysctl
is per-interface or system-wide for all interfaces
$ sysctl -w net.ipv6.conf.eth1.keep_addr_on_down=1
or
$ sysctl -w net.ipv6.conf.all.keep_addr_on_down=1
Will keep addresses on eth1 on an admin down.
$ ip -6 addr show dev eth1
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 state UP qlen 1000
inet6 2100:1::2/120 scope global
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe79:34bd/64 scope link
valid_lft forever preferred_lft forever
$ ip link set dev eth1 down
$ ip -6 addr show dev eth1
3: eth1: <BROADCAST,MULTICAST> mtu 1500 state DOWN qlen 1000
inet6 2100:1::2/120 scope global tentative
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe79:34bd/64 scope link tentative
valid_lft forever preferred_lft forever
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
An error response from a RTM_GETNETCONF request can return the positive
error value EINVAL in the struct nlmsgerr that can mislead userspace.
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain 802.11 wireless deployments, there will be NA proxies
that use knowledge of the network to correctly answer requests.
To prevent unsolicitd advertisements on the shared medium from
being a problem, on such deployments wireless needs to drop them.
Enable this by providing an option called "drop_unsolicited_na".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to solve a problem with 802.11, the so-called hole-196 attack,
add an option (sysctl) called "drop_unicast_in_l2_multicast" which, if
enabled, causes the stack to drop IPv6 unicast packets encapsulated in
link-layer multi- or broadcast frames. Such frames can (as an attack)
be created by any member of the same wireless network and transmitted
as valid encrypted frames since the symmetric key for broadcast frames
is shared between all stations.
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A rcu stall with the following backtrace was seen on a system with
forwarding, optimistic_dad and use_optimistic set. To reproduce,
set these flags and allow ipv6 autoconf.
This occurs because the device write_lock is acquired while already
holding the read_lock. Back trace below -
INFO: rcu_preempt self-detected stall on CPU { 1} (t=2100 jiffies
g=3992 c=3991 q=4471)
<6> Task dump for CPU 1:
<2> kworker/1:0 R running task 12168 15 2 0x00000002
<2> Workqueue: ipv6_addrconf addrconf_dad_work
<6> Call trace:
<2> [<ffffffc000084da8>] el1_irq+0x68/0xdc
<2> [<ffffffc000cc4e0c>] _raw_write_lock_bh+0x20/0x30
<2> [<ffffffc000bc5dd8>] __ipv6_dev_ac_inc+0x64/0x1b4
<2> [<ffffffc000bcbd2c>] addrconf_join_anycast+0x9c/0xc4
<2> [<ffffffc000bcf9f0>] __ipv6_ifa_notify+0x160/0x29c
<2> [<ffffffc000bcfb7c>] ipv6_ifa_notify+0x50/0x70
<2> [<ffffffc000bd035c>] addrconf_dad_work+0x314/0x334
<2> [<ffffffc0000b64c8>] process_one_work+0x244/0x3fc
<2> [<ffffffc0000b7324>] worker_thread+0x2f8/0x418
<2> [<ffffffc0000bb40c>] kthread+0xe0/0xec
v2: do addrconf_dad_kick inside read lock and then acquire write
lock for ipv6_ifa_notify as suggested by Eric
Fixes: 7fd2561e4e ("net: ipv6: Add a sysctl to make optimistic
addresses useful candidates")
Cc: Eric Dumazet <edumazet@google.com>
Cc: Erik Kline <ek@google.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The userspace needs to know why is the address being removed so that it can
perhaps obtain a new address.
Without the DADFAILED flag it's impossible to distinguish removal of a
temporary and tentative address due to DAD failure from other reasons (device
removed, manual address removal).
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sysctl performs restrict writes, it allows to write from
a middle position of a sysctl file, which requires us to initialize
the table data before calling proc_dostring() for the write case.
Fixes: 3d1bec9932 ("ipv6: introduce secret_stable to ipv6_devconf")
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new address generator mode, using the stable address generator
with an automatically generated secret. This is intended as a default
address generator mode for device types with no EUI64 implementation.
The new generator is used for ARPHRD_NONE interfaces initially, adding
default IPv6 autoconf support to e.g. tun interfaces.
If the addrgenmode is set to 'random', either by default or manually,
and no stable secret is available, then a random secret is used as
input for the stable-privacy address generator. The secret can be
read and modified like manually configured secrets, using the proc
interface. Modifying the secret will change the addrgen mode to
'stable-privacy' to indicate that it operates on a known secret.
Existing behaviour of the 'stable-privacy' mode is kept unchanged. If
a known secret is available when the device is created, then the mode
will default to 'stable-privacy' as before. The mode can be manually
set to 'random' but it will behave exactly like 'stable-privacy' in
this case. The secret will not change.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: 吉藤英明 <hideaki.yoshifuji@miraclelinux.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn reported that while we switch all interfaces to privacy stable mode
when setting the secret, we don't set this mode for new interfaces. This
does not make sense, so change this behaviour.
Fixes: 622c81d57b ("ipv6: generation of stable privacy addresses for link-local and autoconf")
Reported-by: Bjørn Mork <bjorn@mork.no>
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes ARPHRD_IEEE802154 from addrconf handling. In the
earlier days of 802.15.4 6LoWPAN, the interface type was ARPHRD_IEEE802154
which introduced several issues, because 802.15.4 interfaces used the
same type.
Since commit 965e613d29 ("ieee802154: 6lowpan: fix ARPHRD to
ARPHRD_6LOWPAN") we use ARPHRD_6LOWPAN for 6LoWPAN interfaces. This
patch will remove ARPHRD_IEEE802154 which is currently deadcode, because
ARPHRD_IEEE802154 doesn't reach the minimum 1280 MTU of IPv6.
Also we use 6LoWPAN EUI64 specific defines instead using link-layer
constanst from 802.15.4 link-layer header.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 64236f3f3d ("ipv6: introduce IFA_F_STABLE_PRIVACY flag")
failed to update the setting of the IFA_F_OPTIMISTIC flag, causing
the IFA_F_STABLE_PRIVACY flag to be lost if IFA_F_OPTIMISTIC is set.
Cc: Erik Kline <ek@google.com>
Cc: Fernando Gont <fgont@si6networks.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: YOSHIFUJI Hideaki/吉藤英明 <hideaki.yoshifuji@miraclelinux.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Fixes: 64236f3f3d ("ipv6: introduce IFA_F_STABLE_PRIVACY flag")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
An interface changing type may not have IPv6 addresses. Don't
call the address configuration type change in this case.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting a value bigger than 255 resulted in using only the lower eight
bits of that value as it is assigned to the u8 header field. To avoid
this unexpected result, reject such values.
Setting a value of zero is technically possible, but hosts receiving
such a packet have to treat it like hop_limit was set to one, according
to RFC2460. Therefore I don't see a use-case for that.
Setting a route's hop_limit to zero in iproute2 means to use the sysctl
default, which is not the case here: Setting e.g.
net.conf.eth0.hop_limit=0 will not make the kernel use
net.conf.all.hop_limit for outgoing packets on eth0. To avoid these
kinds of confusion, reject zero.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ab450605b3.
In IPv6, we cannot inherit the dst of the original dst. ndisc packets
are IPv6 packets and may take another route than the original packet.
This patch breaks the following scenario: a packet comes from eth0 and
is forwarded through vxlan1. The encapsulated packet triggers an NS
which cannot be sent because of the wrong route.
CC: Jiri Benc <jbenc@redhat.com>
CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipv6_add_dev, when addrconf_sysctl_register fails, we do not clean up
the dev_snmp6 entry that we have already registered for this device.
Call snmp6_unregister_dev in this case.
Fixes: a317a2f19d ("ipv6: fail early when creating netdev named all or default")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that we reinitialize the interface if the MTU is
increased back above IPV6_MIN_MTU and the interface is up.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if_nlmsg_size() overestimates the minimum allocation size of netlink
dump request (when called from rtnl_calcit()) or the size of the
message (when called from rtnl_getlink()). This is because
ext_filter_mask is not supported by rtnl_link_get_af_size() and
rtnl_link_get_size().
The over-estimation is significant when at least one netdev has many
VLANs configured (8 bytes for each configured VLAN).
This patch-set "rightsizes" the protocol specific attribute size
calculation by propagating ext_filter_mask to rtnl_link_get_af_size()
and adding this a argument to get_link_af_size op in rtnl_af_ops.
Bridge module already used filtering aware sizing for notifications.
br_get_link_af_size_filtered() is consistent with the modified
get_link_af_size op so it replaces br_get_link_af_size() in br_af_ops.
br_get_link_af_size() becomes unused and thus removed.
Signed-off-by: Ronen Arad <ronen.arad@intel.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
As with IPv4 support for VRFs added to IPv6 stack by replacing hardcoded
table ids with possibly device specific ones and manipulating the oif in
the flowi6. The flow flags are used to skip oif compare in nexthop lookups
if the device is enslaved to a VRF via the L3 master device.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRE point-to-point interfaces should also support ipv6 multicast. Setting
up default multicast routes on interface creation was forgotten. Add it.
Bugzilla: <https://bugzilla.kernel.org/show_bug.cgi?id=103231>
Cc: Julien Muchembled <jm@jmuchemb.eu>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Nicolas Dumazet <ndumazet@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/arp.c
The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 12fd84f438 ("ipv6: Remove unused neigh argument for
icmp6_dst_alloc() and its callers."), the neigh parameter of ndisc_send_na
and ndisc_send_ns is unused.
CC: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many commonly used functions like getifaddrs() invoke RTM_GETLINK
to dump the interface information, and do not need the
the AF_INET6 statististics that are always returned by default
from rtnl_fill_ifinfo().
Computing the statistics can be an expensive operation that impacts
scaling, so it is desirable to avoid this if the information is
not needed.
This patch adds a the RTEXT_FILTER_SKIP_STATS extended info flag that
can be passed with netlink_request() to avoid statistics computation
for the ifinfo path.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a prep work to get dst freeing from fib tree undergo
a rcu grace period.
The following is a common paradigm:
if (ip6_del_rt(rt))
dst_free(rt)
which means, if rt cannot be deleted from the fib tree, dst_free(rt) now.
1. We don't know the ip6_del_rt(rt) failure is because it
was not managed by fib tree (e.g. DST_NOCACHE) or it had already been
removed from the fib tree.
2. If rt had been managed by the fib tree, ip6_del_rt(rt) failure means
dst_free(rt) has been called already. A second
dst_free(rt) is not always obviously safe. The rt may have
been destroyed already.
3. If rt is a DST_NOCACHE, dst_free(rt) should not be called.
4. It is a stopper to make dst freeing from fib tree undergo a
rcu grace period.
This patch is to use a DST_NOCACHE flag to indicate a rt is
not managed by the fib tree.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Create drivers/staging/rdma
- Move amso1100 driver to staging/rdma and schedule for deletion
- Move ipath driver to staging/rdma and schedule for deletion
- Add hfi1 driver to staging/rdma and set TODO for move to regular tree
- Initial support for namespaces to be used on RDMA devices
- Add RoCE GID table handling to the RDMA core caching code
- Infrastructure to support handling of devices with differing
read and write scatter gather capabilities
- Various iSER updates
- Kill off unsafe usage of global mr registrations
- Update SRP driver
- Misc. mlx4 driver updates
- Support for the mr_alloc verb
- Support for a netlink interface between kernel and user space cache
daemon to speed path record queries and route resolution
- Ininitial support for safe hot removal of verbs devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=EHLg
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull inifiniband/rdma updates from Doug Ledford:
"This is a fairly sizeable set of changes. I've put them through a
decent amount of testing prior to sending the pull request due to
that.
There are still a few fixups that I know are coming, but I wanted to
go ahead and get the big, sizable chunk into your hands sooner rather
than waiting for those last few fixups.
Of note is the fact that this creates what is intended to be a
temporary area in the drivers/staging tree specifically for some
cleanups and additions that are coming for the RDMA stack. We
deprecated two drivers (ipath and amso1100) and are waiting to hear
back if we can deprecate another one (ehca). We also put Intel's new
hfi1 driver into this area because it needs to be refactored and a
transfer library created out of the factored out code, and then it and
the qib driver and the soft-roce driver should all be modified to use
that library.
I expect drivers/staging/rdma to be around for three or four kernel
releases and then to go away as all of the work is completed and final
deletions of deprecated drivers are done.
Summary of changes for 4.3:
- Create drivers/staging/rdma
- Move amso1100 driver to staging/rdma and schedule for deletion
- Move ipath driver to staging/rdma and schedule for deletion
- Add hfi1 driver to staging/rdma and set TODO for move to regular
tree
- Initial support for namespaces to be used on RDMA devices
- Add RoCE GID table handling to the RDMA core caching code
- Infrastructure to support handling of devices with differing read
and write scatter gather capabilities
- Various iSER updates
- Kill off unsafe usage of global mr registrations
- Update SRP driver
- Misc mlx4 driver updates
- Support for the mr_alloc verb
- Support for a netlink interface between kernel and user space cache
daemon to speed path record queries and route resolution
- Ininitial support for safe hot removal of verbs devices"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (136 commits)
IB/ipoib: Suppress warning for send only join failures
IB/ipoib: Clean up send-only multicast joins
IB/srp: Fix possible protection fault
IB/core: Move SM class defines from ib_mad.h to ib_smi.h
IB/core: Remove unnecessary defines from ib_mad.h
IB/hfi1: Add PSM2 user space header to header_install
IB/hfi1: Add CSRs for CONFIG_SDMA_VERBOSITY
mlx5: Fix incorrect wc pkey_index assignment for GSI messages
IB/mlx5: avoid destroying a NULL mr in reg_user_mr error flow
IB/uverbs: reject invalid or unknown opcodes
IB/cxgb4: Fix if statement in pick_local_ip6adddrs
IB/sa: Fix rdma netlink message flags
IB/ucma: HW Device hot-removal support
IB/mlx4_ib: Disassociate support
IB/uverbs: Enable device removal when there are active user space applications
IB/uverbs: Explicitly pass ib_dev to uverbs commands
IB/uverbs: Fix race between ib_uverbs_open and remove_one
IB/uverbs: Fix reference counting usage of event files
IB/core: Make ib_dealloc_pd return void
IB/srp: Create an insecure all physical rkey only if needed
...
Docker container creation linearly increased from around 1.6 sec to 7.5 sec
(at 1000 containers) and perf data showed 50% ovehead in snmp_fold_field.
reason: currently __snmp6_fill_stats64 calls snmp_fold_field that walks
through per cpu data of an item (iteratively for around 36 items).
idea: This patch tries to aggregate the statistics by going through
all the items of each cpu sequentially which is reducing cache
misses.
Docker creation got faster by more than 2x after the patch.
Result:
Before After
Docker creation time 6.836s 3.25s
cache miss 2.7% 1.41%
perf before:
50.73% docker [kernel.kallsyms] [k] snmp_fold_field
9.07% swapper [kernel.kallsyms] [k] snooze_loop
3.49% docker [kernel.kallsyms] [k] veth_stats_one
2.85% swapper [kernel.kallsyms] [k] _raw_spin_lock
perf after:
10.57% docker docker [.] scanblock
8.37% swapper [kernel.kallsyms] [k] snooze_loop
6.91% docker [kernel.kallsyms] [k] snmp_get_cpu_field
6.67% docker [kernel.kallsyms] [k] veth_stats_one
changes/ideas suggested:
Using buffer in stack (Eric), Usage of memset (David), Using memcpy in
place of unaligned_put (Joe).
Signed-off-by: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For loopback purposes, RoCE devices should have a default GID in the
port GID table, even when the interface is down. In order to do so,
we use the IPv6 link local address which would have been genenrated
for the related Ethernet netdevice when it goes up as a default GID.
addrconf_ifid_eui48 is used to gernerate this address, export it.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If output device wants to see the dst, inherit the dst of the original skb
in the ndisc request.
This is an IPv6 counterpart of commit 0accfc268f ("arp: Inherit metadata
dst when creating ARP requests").
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is useful information to include in ipv6 netlink messages that
report interface information. IFLA_OPERSTATE is already included in
ipv4 messages, but missing for ipv6. This closes that gap.
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the ipv4 patch with a similar title, this adds a sysctl to allow
the user to change routing behavior based on whether or not the
interface associated with the nexthop was an up or down link. The
default setting preserves the current behavior, but anyone that enables
it will notice that nexthops on down interfaces will no longer be
selected:
net.ipv6.conf.all.ignore_routes_with_linkdown = 0
net.ipv6.conf.default.ignore_routes_with_linkdown = 0
net.ipv6.conf.lo.ignore_routes_with_linkdown = 0
...
When the above sysctls are set, not only will link status be reported to
userspace, but an indication that a nexthop is dead and will not be used
is also reported.
1000::/8 via 7000::2 dev p7p1 metric 1024 dead linkdown pref medium
1000::/8 via 8000::2 dev p8p1 metric 1024 pref medium
7000::/8 dev p7p1 proto kernel metric 256 dead linkdown pref medium
8000::/8 dev p8p1 proto kernel metric 256 pref medium
9000::/8 via 8000::2 dev p8p1 metric 2048 pref medium
9000::/8 via 7000::2 dev p7p1 metric 1024 dead linkdown pref medium
fe80::/64 dev p7p1 proto kernel metric 256 dead linkdown pref medium
fe80::/64 dev p8p1 proto kernel metric 256 pref medium
This also adds devconf support and notification when sysctl values
change.
v2: drop use of rt6i_nhflags since it is not needed right now
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6fd99094de ("ipv6: Don't reduce hop limit for an interface")
disabled accept hop limit from RA if it is smaller than the current hop
limit for security stuff. But this behavior kind of break the RFC definition.
RFC 4861, 6.3.4. Processing Received Router Advertisements
A Router Advertisement field (e.g., Cur Hop Limit, Reachable Time,
and Retrans Timer) may contain a value denoting that it is
unspecified. In such cases, the parameter should be ignored and the
host should continue using whatever value it is already using.
If the received Cur Hop Limit value is non-zero, the host SHOULD set
its CurHopLimit variable to the received value.
So add sysctl option accept_ra_min_hop_limit to let user choose the minimum
hop limit value they can accept from RA. And set default to 1 to meet RFC
standards.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per RFC 6724, section 4, "Candidate Source Addresses":
It is RECOMMENDED that the candidate source addresses be the set
of unicast addresses assigned to the interface that will be used
to send to the destination (the "outgoing" interface).
Add a sysctl to enable this behaviour.
Signed-off-by: Erik Kline <ek@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9131f3de2 ("ipv6: Do not iterate over all interfaces when
finding source address on specific interface.") did not properly
update best source address available. Plus, it introduced
possible NULL pointer dereference.
Bug was reported by Erik Kline <ek@google.com>.
Based on patch proposed by Hajime Tazaki <thehajime@gmail.com>.
Fixes: 9131f3de24 ("ipv6: Do not
iterate over all interfaces when finding source address
on specific interface.")
Signed-off-by: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Acked-by: Hajime Tazaki <thehajime@gmail.com>
Acked-by: Erik Kline <ek@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If outgoing interface is specified and the candidate address is
restricted to the outgoing interface, it is enough to iterate
over that given interface only.
Signed-off-by: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Acked-by: Erik Kline <ek@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a prep work for the later bug-fix patch which will stop /128 route
from disappearing after pmtu update.
The later bug-fix patch will allow a /128 route and its RTF_CACHE clone
both exist at the same fib6_node. To do this, we need to prepare the
existing fib6 tree search to expect RTF_CACHE for /128 route.
Note that the fn->leaf is sorted by rt6i_metric. Hence,
RTF_CACHE (if there is any) is always at the front. This property
leads to the following:
1. When doing ip6_route_del(), it should honor the RTF_CACHE flag which
the caller is used to ask for deleting clone or non-clone.
The rtm_to_fib6_config() should also check the RTM_F_CLONED and
then set RTF_CACHE accordingly so that:
- 'ip -6 r del...' will make ip6_route_del() to delete a route
and all its clones. Note that its clones is flushed by fib6_del()
- 'ip -6 r flush table cache' will make ip6_route_del() to
only delete clone(s).
2. Exclude RTF_CACHE from addrconf_get_prefix_route() which
should not configure on a cloned route.
3. No change is need for rt6_device_match() since it currently could
return a RTF_CACHE clone route, so the later bug-fix patch will not
affect it.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this patch is to prepare the removal of the iflink field. It
introduces a new ndo function, which will be implemented by virtual interfaces.
There is no functional change into this patch. All readers of iflink field
now call dev_get_iflink().
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP addresses are often stored in netlink attributes. Add generic functions
to do that.
For nla_put_in_addr, it would be nicer to pass struct in_addr but this is
not used universally throughout the kernel, in way too many places __be32 is
used to store IPv4 address.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv6 code uses a mixture of coding styles. In some instances check for NULL
pointer is done as x == NULL and sometimes as !x. !x is preferred according to
checkpatch and this patch makes the code consistent by adopting the latter
form.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those warnings reported by sparse endianness check (via kbuild test robot)
are harmless, nevertheless fix them up and make the code a little bit
easier to read.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 622c81d57b ("ipv6: generation of stable privacy addresses for link-local and autoconf")
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is specified by RFC 7217.
Cc: Erik Kline <ek@google.com>
Cc: Fernando Gont <fgont@si6networks.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: YOSHIFUJI Hideaki/吉藤英明 <hideaki.yoshifuji@miraclelinux.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a DAD conflict is detected, we want to retry privacy stable address
generation up to idgen_retries (= 3) times with a delay of idgen_delay
(= 1 second). Add the logic to addrconf_dad_failure.
By design, we don't clean up dad failed permanent addresses.
Cc: Erik Kline <ek@google.com>
Cc: Fernando Gont <fgont@si6networks.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: YOSHIFUJI Hideaki/吉藤英明 <hideaki.yoshifuji@miraclelinux.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Erik Kline <ek@google.com>
Cc: Fernando Gont <fgont@si6networks.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: YOSHIFUJI Hideaki/吉藤英明 <hideaki.yoshifuji@miraclelinux.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to mark appropriate addresses so we can do retries in case their
DAD failed.
Cc: Erik Kline <ek@google.com>
Cc: Fernando Gont <fgont@si6networks.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: YOSHIFUJI Hideaki/吉藤英明 <hideaki.yoshifuji@miraclelinux.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the stable privacy address generation for
link-local and autoconf addresses as specified in RFC7217.
RID = F(Prefix, Net_Iface, Network_ID, DAD_Counter, secret_key)
is the RID (random identifier). As the hash function F we chose one
round of sha1. Prefix will be either the link-local prefix or the
router advertised one. As Net_Iface we use the MAC address of the
device. DAD_Counter and secret_key are implemented as specified.
We don't use Network_ID, as it couples the code too closely to other
subsystems. It is specified as optional in the RFC.
As Net_Iface we only use the MAC address: we simply have no stable
identifier in the kernel we could possibly use: because this code might
run very early, we cannot depend on names, as they might be changed by
user space early on during the boot process.
A new address generation mode is introduced,
IN6_ADDR_GEN_MODE_STABLE_PRIVACY. With iproute2 one can switch back to
none or eui64 address configuration mode although the stable_secret is
already set.
We refuse writes to ipv6/conf/all/stable_secret but only allow
ipv6/conf/default/stable_secret and the interface specific file to be
written to. The default stable_secret is used as the parameter for the
namespace, the interface specific can overwrite the secret, e.g. when
switching a network configuration from one system to another while
inheriting the secret.
Cc: Erik Kline <ek@google.com>
Cc: Fernando Gont <fgont@si6networks.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: YOSHIFUJI Hideaki/吉藤英明 <hideaki.yoshifuji@miraclelinux.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the procfs logic for the stable_address knob:
The secret is formatted as an ipv6 address and will be stored per
interface and per namespace. We track initialized flag and return EIO
errors until the secret is set.
We don't inherit the secret to newly created namespaces.
Cc: Erik Kline <ek@google.com>
Cc: Fernando Gont <fgont@si6networks.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: YOSHIFUJI Hideaki/吉藤英明 <hideaki.yoshifuji@miraclelinux.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
in favor of their inner __ ones, which doesn't grab rtnl.
As these functions need to operate on a locked socket, we can't be
grabbing rtnl by then. It's too late and doing so causes reversed
locking.
So this patch:
- move rtnl handling to callers instead while already fixing some
reversed locking situations, like on vxlan and ipvs code.
- renames __ ones to not have the __ mark:
__ip_mc_{join,leave}_group -> ip_mc_{join,leave}_group
__ipv6_sock_mc_{join,drop} -> ipv6_sock_mc_{join,drop}
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Joining multicast group on ethernet level via "ip maddr" command would
not work if we have an Ethernet switch that does igmp snooping since
the switch would not replicate multicast packets on ports that did not
have IGMP reports for the multicast addresses.
Linux vxlan interfaces created via "ip link add vxlan" have the group option
that enables then to do the required join.
By extending ip address command with option "autojoin" we can get similar
functionality for openvswitch vxlan interfaces as well as other tunneling
mechanisms that need to receive multicast traffic. The kernel code is
structured similar to how the vxlan driver does a group join / leave.
example:
ip address add 224.1.1.10/24 dev eth5 autojoin
ip address del 224.1.1.10/24 dev eth5
Signed-off-by: Madhu Challa <challa@noironetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we don't check if the new MTU is valid or not and this allows
one to configure a smaller than minimum allowed by RFCs or even bigger
than interface own MTU, which is a problem as it may lead to packet
drops.
If you have a daemon like NetworkManager running, this may be exploited
by remote attackers by forging RA packets with an invalid MTU, possibly
leading to a DoS. (NetworkManager currently only validates for values
too small, but not for too big ones.)
The fix is just to make sure the new value is valid. That is, between
IPV6_MIN_MTU and interface's MTU.
Note that similar check is already performed at
ndisc_router_discovery(), for when kernel itself parses the RA.
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We still need a validate_link_af() handler with an appropriate nla policy,
similarly as we have in IPv4 case, otherwise size validations are not being
done properly in that case.
Fixes: f53adae4ea ("net: ipv6: add tokenized interface identifier support")
Fixes: bc91b0f07a ("ipv6: addrconf: implement address generation modes")
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 4429 ("Optimistic DAD") states that optimistic addresses
should be treated as deprecated addresses. From section 2.1:
Unless noted otherwise, components of the IPv6 protocol stack
should treat addresses in the Optimistic state equivalently to
those in the Deprecated state, indicating that the address is
available for use but should not be used if another suitable
address is available.
Optimistic addresses are indeed avoided when other addresses are
available (i.e. at source address selection time), but they have
not heretofore been available for things like explicit bind() and
sendmsg() with struct in6_pktinfo, etc.
This change makes optimistic addresses treated more like
deprecated addresses than tentative ones.
Signed-off-by: Erik Kline <ek@google.com>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are all either written once or extremly rarely (e.g. from init
code), so we can move them to the .data..read_mostly section.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel forcefully applies MTU values received in router
advertisements provided the new MTU is less than the current. This
behavior is undesirable when the user space is managing the MTU. Instead
a sysctl flag 'accept_ra_mtu' is introduced such that the user space
can control whether or not RA provided MTU updates should be applied. The
default behavior is unchanged; user space must explicitly set this flag
to 0 for RA MTUs to be ignored.
Signed-off-by: Harout Hedeshian <harouth@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 053c095a82 ("netlink: make nlmsg_end() and genlmsg_end()
void") didn't catch all of the cases where callers were breaking out
on the return value being equal to zero, which they no longer should
when zero means success.
Fix all such cases.
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Reported-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Contrary to common expectations for an "int" return, these functions
return only a positive value -- if used correctly they cannot even
return 0 because the message header will necessarily be in the skb.
This makes the very common pattern of
if (genlmsg_end(...) < 0) { ... }
be a whole bunch of dead code. Many places also simply do
return nlmsg_end(...);
and the caller is expected to deal with it.
This also commonly (at least for me) causes errors, because it is very
common to write
if (my_function(...))
/* error condition */
and if my_function() does "return nlmsg_end()" this is of course wrong.
Additionally, there's not a single place in the kernel that actually
needs the message length returned, and if anyone needs it later then
it'll be very easy to just use skb->len there.
Remove this, and make the functions void. This removes a bunch of dead
code as described above. The patch adds lines because I did
- return nlmsg_end(...);
+ nlmsg_end(...);
+ return 0;
I could have preserved all the function's return values by returning
skb->len, but instead I've audited all the places calling the affected
functions and found that none cared. A few places actually compared
the return value with <= 0 in dump functionality, but that could just
be changed to < 0 with no change in behaviour, so I opted for the more
efficient version.
One instance of the error I've made numerous times now is also present
in net/phonet/pn_netlink.c in the route_dumpit() function - it didn't
check for <0 or <=0 and thus broke out of the loop every single time.
I've preserved this since it will (I think) have caused the messages to
userspace to be formatted differently with just a single message for
every SKB returned to userspace. It's possible that this isn't needed
for the tools that actually use this, but I don't even know what they
are so couldn't test that changing this behaviour would be acceptable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "init_net" test in function addrconf_exit_net is introduced
in commit 44a6bd29 [Create ipv6 devconf-s for namespaces] to avoid freeing
init_net. In commit c900a800 [ipv6: fix bad free of addrconf_init_net],
function addrconf_init_net will allocate memory for every net regardless of
init_net. In this case, it is unnecessary to make "init_net" test.
CC: Hong Zhiguo <honkiko@gmail.com>
CC: Octavian Purdila <opurdila@ixiacom.com>
CC: Pavel Emelyanov <xemul@openvz.org>
CC: Cong Wang <cwang@twopensource.com>
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Zhu Yanjun <Yanjun.Zhu@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change has no functional impact and simply addresses some coding
style issues detected by checkpatch. Specifically this change
adjusts "if" statements which also include the assignment of a
variable.
No changes to the resultant object files result as determined by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the more common dynamic_debug capable net_dbg_ratelimited
and remove the LIMIT_NETDEBUG macro.
All messages are still ratelimited.
Some KERN_<LEVEL> uses are changed to KERN_DEBUG.
This may have some negative impact on messages that were
emitted at KERN_INFO that are not not enabled at all unless
DEBUG is defined or dynamic_debug is enabled. Even so,
these messages are now _not_ emitted by default.
This also eliminates the use of the net_msg_warn sysctl
"/proc/sys/net/core/warnings". For backward compatibility,
the sysctl is not removed, but it has no function. The extern
declaration of net_msg_warn is removed from sock.h and made
static in net/core/sysctl_net_core.c
Miscellanea:
o Update the sysctl documentation
o Remove the embedded uses of pr_fmt
o Coalesce format fragments
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a sysctl that causes an interface's optimistic addresses
to be considered equivalent to other non-deprecated addresses
for source address selection purposes. Preferred addresses
will still take precedence over optimistic addresses, subject
to other ranking in the source address selection algorithm.
This is useful where different interfaces are connected to
different networks from different ISPs (e.g., a cell network
and a home wifi network).
The current behaviour complies with RFC 3484/6724, and it
makes sense if the host has only one interface, or has
multiple interfaces on the same network (same or cooperating
administrative domain(s), but not in the multiple distinct
networks case.
For example, if a mobile device has an IPv6 address on an LTE
network and then connects to IPv6-enabled wifi, while the wifi
IPv6 address is undergoing DAD, IPv6 connections will try use
the wifi default route with the LTE IPv6 address, and will get
stuck until they time out.
Also, because optimistic nodes can receive frames, issue
an RTM_NEWADDR as soon as DAD starts (with the IFA_F_OPTIMSTIC
flag appropriately set). A second RTM_NEWADDR is sent if DAD
completes (the address flags have changed), otherwise an
RTM_DELADDR is sent.
Also: add an entry in ip-sysctl.txt for optimistic_dad.
Signed-off-by: Erik Kline <ek@google.com>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
NetworkManager might want to know that it changed when the router advertisement
arrives.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
net/netfilter/nfnetlink.c
Both r8152 and nfnetlink conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet noticed that all no-nonexthop or no-gateway routes which
are already marked DST_HOST (e.g. input routes routes) will always be
invalidated during sk_dst_check. Thus per-socket dst caching absolutely
had no effect and early demuxing had no effect.
Thus this patch removes rt6i_genid: fn_sernum already gets modified during
add operations, so we only must ensure we mutate fn_sernum during ipv6
address remove operations. This is a fairly cost extensive operations,
but address removal should not happen that often. Also our mtu update
functions do the same and we heard no complains so far. xfrm policy
changes also cause a call into fib6_flush_trees. Also plug a hole in
rt6_info (no cacheline changes).
I verified via tracing that this change has effect.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: YOSHIFUJI Hideaki <hideaki@yoshifuji.org>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Martin Lau <kafai@fb.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
If IPv6 is explicitly disabled before the interface comes up,
it makes no sense to continue when it comes up, even just
print a message.
(I am not sure about other cases though, so I prefer not to touch)
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it accept inet6_dev, and rename it to __ipv6_dev_ac_inc()
to reflect this change.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we try to rmmod the driver for an interface while sockets with
setsockopt(JOIN_ANYCAST) are alive, some refcounts aren't cleaned up
and we get stuck on:
unregister_netdevice: waiting for ens3 to become free. Usage count = 1
If we LEAVE_ANYCAST/close everything before rmmod'ing, there is no
problem.
We need to perform a cleanup similar to the one for multicast in
addrconf_ifdown(how == 1).
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
addrconf_get_prefix_route() ensures to get the right route in the right table.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to take a refcnt before deleting the peer address route.
It's done some lines below for the local prefix route because
inet6_ifa_finish_destroy() will release it at the end.
For the peer address route, we want to free it right now.
This bug has been introduced by commit
caeaba7900 ("ipv6: add support of peer address").
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling setsockopt with IPV6_JOIN_ANYCAST or IPV6_LEAVE_ANYCAST
triggers the assertion in addrconf_join_solict()/addrconf_leave_solict()
ipv6_sock_ac_join(), ipv6_sock_ac_drop(), ipv6_sock_ac_close() need to
take RTNL before calling ipv6_dev_ac_inc/dec. Same thing with
ipv6_sock_mc_join(), ipv6_sock_mc_drop(), ipv6_sock_mc_close() before
calling ipv6_dev_mc_inc/dec.
This patch moves ASSERT_RTNL() up a level in the call stack.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reported-by: Tommi Rantala <tt.rantala@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes no changes to the logic of the code but simply addresses
coding style issues as detected by checkpatch.
Both objdump and diff -w show no differences.
A number of items are addressed in this patch:
* Multiple spaces converted to tabs
* Spaces before tabs removed.
* Spaces in pointer typing cleansed (char *)foo etc.
* Remove space after sizeof
* Ensure spacing around comparators such as if statements.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We create a proc dir for each network device, this will cause
conflicts when the devices have name "all" or "default".
Rather than emitting an ugly kernel warning, we could just
fail earlier by checking the device name.
Reported-by: Stephane Chazelas <stephane.chazelas@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a possibility for userspace to set various (so far
two) modes of generating addresses. This is useful for example for
NetworkManager because it can set the mode to NONE and take care of link
local addresses itself. That allow it to have the interface up,
monitoring carrier but still don't have any addresses on it.
One more use-case by Dan Williams:
<quote>
WWAN devices often have their LL address provided by the firmware of the
device, which sometimes refuses to respond to incorrect LL addresses
when doing DHCPv6 or IPv6 ND. The kernel cannot generate the correct LL
address for two reasons:
1) WWAN pseudo-ethernet interfaces often construct a fake MAC address,
or read a meaningless MAC address from the firmware. Thus the EUI64 and
the IPv6LL address the kernel assigns will be wrong. The real LL
address is often retrieved from the firmware with AT or proprietary
commands.
2) WWAN PPP interfaces receive their LL address from IPV6CP, not from
kernel assignments. Only after IPV6CP has completed do we know the LL
address of the PPP interface and its peer. But the kernel has already
assigned an incorrect LL address to the interface.
So being able to suppress the kernel LL address generation and assign
the one retrieved from the firmware is less complicated and more robust.
</quote>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This can be used in virtual networking applications, and
may have other uses as well. The option is disabled by
default.
A specific use case is setting up virtual routers, bridges, and
hosts on a single OS without the use of network namespaces or
virtual machines. With proper use of ip rules, routing tables,
veth interface pairs and/or other virtual interfaces,
and applications that can bind to interfaces and/or IP addresses,
it is possibly to create one or more virtual routers with multiple
hosts attached. The host interfaces can act as IPv6 systems,
with radvd running on the ports in the virtual routers. With the
option provided in this patch enabled, those hosts can now properly
obtain IPv6 addresses from the radvd.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 8f0ea0fe3a (snmp: reduce percpu needs by 50%)
reduced snmp array size to 1, so technically it doesn't have to be
an array any more. What's more, after the following commit:
commit 933393f58f
Date: Thu Dec 22 11:58:51 2011 -0600
percpu: Remove irqsafe_cpu_xxx variants
We simply say that regular this_cpu use must be safe regardless of
preemption and interrupt state. That has no material change for x86
and s390 implementations of this_cpu operations. However, arches that
do not provide their own implementation for this_cpu operations will
now get code generated that disables interrupts instead of preemption.
probably no arch wants to have SNMP_ARRAY_SZ == 2. At least after
almost 3 years, no one complains.
So, just convert the array to a single pointer and remove snmp_mib_init()
and snmp_mib_free() as well.
Cc: Christoph Lameter <cl@linux.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is no longer used after commit e837735ec4
(ip6_tunnel: ensure to always have a link local address).
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Userspace applications can use IFA_F_MANAGETEMPADDR with RTM_NEWADDR
already to indicate that the kernel should take care of temporary
address management.
This patch adds related functionality to RTM_DELADDR. By setting
IFA_F_MANAGETEMPADDR a userspace application can indicate that the kernel
should delete all related temporary addresses as well.
A corresponding patch for the "ip addr del" command has been applied to
iproute2 already.
Signed-off-by: Heiner Kallweit <heiner.kallweit@web.de>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
addrconf_join_solict and addrconf_join_anycast may cause actions which
need rtnl locked, especially on first address creation.
A new DAD state is introduced which defers processing of the initial
DAD processing into a workqueue.
To get rtnl lock we need to push the code paths which depend on those
calls up to workqueues, specifically addrconf_verify and the DAD
processing.
(v2)
addrconf_dad_failure needs to be queued up to the workqueue, too. This
patch introduces a new DAD state and stop the DAD processing in the
workqueue (this is because of the possible ipv6_del_addr processing
which removes the solicited multicast address from the device).
addrconf_verify_lock is removed, too. After the transition it is not
needed any more.
As we are not processing in bottom half anymore we need to be a bit more
careful about disabling bottom half out when we lock spin_locks which are also
used in bh.
Relevant backtrace:
[ 541.030090] RTNL: assertion failed at net/core/dev.c (4496)
[ 541.031143] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G O 3.10.33-1-amd64-vyatta #1
[ 541.031145] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[ 541.031146] ffffffff8148a9f0 000000000000002f ffffffff813c98c1 ffff88007c4451f8
[ 541.031148] 0000000000000000 0000000000000000 ffffffff813d3540 ffff88007fc03d18
[ 541.031150] 0000880000000006 ffff88007c445000 ffffffffa0194160 0000000000000000
[ 541.031152] Call Trace:
[ 541.031153] <IRQ> [<ffffffff8148a9f0>] ? dump_stack+0xd/0x17
[ 541.031180] [<ffffffff813c98c1>] ? __dev_set_promiscuity+0x101/0x180
[ 541.031183] [<ffffffff813d3540>] ? __hw_addr_create_ex+0x60/0xc0
[ 541.031185] [<ffffffff813cfe1a>] ? __dev_set_rx_mode+0xaa/0xc0
[ 541.031189] [<ffffffff813d3a81>] ? __dev_mc_add+0x61/0x90
[ 541.031198] [<ffffffffa01dcf9c>] ? igmp6_group_added+0xfc/0x1a0 [ipv6]
[ 541.031208] [<ffffffff8111237b>] ? kmem_cache_alloc+0xcb/0xd0
[ 541.031212] [<ffffffffa01ddcd7>] ? ipv6_dev_mc_inc+0x267/0x300 [ipv6]
[ 541.031216] [<ffffffffa01c2fae>] ? addrconf_join_solict+0x2e/0x40 [ipv6]
[ 541.031219] [<ffffffffa01ba2e9>] ? ipv6_dev_ac_inc+0x159/0x1f0 [ipv6]
[ 541.031223] [<ffffffffa01c0772>] ? addrconf_join_anycast+0x92/0xa0 [ipv6]
[ 541.031226] [<ffffffffa01c311e>] ? __ipv6_ifa_notify+0x11e/0x1e0 [ipv6]
[ 541.031229] [<ffffffffa01c3213>] ? ipv6_ifa_notify+0x33/0x50 [ipv6]
[ 541.031233] [<ffffffffa01c36c8>] ? addrconf_dad_completed+0x28/0x100 [ipv6]
[ 541.031241] [<ffffffff81075c1d>] ? task_cputime+0x2d/0x50
[ 541.031244] [<ffffffffa01c38d6>] ? addrconf_dad_timer+0x136/0x150 [ipv6]
[ 541.031247] [<ffffffffa01c37a0>] ? addrconf_dad_completed+0x100/0x100 [ipv6]
[ 541.031255] [<ffffffff8105313a>] ? call_timer_fn.isra.22+0x2a/0x90
[ 541.031258] [<ffffffffa01c37a0>] ? addrconf_dad_completed+0x100/0x100 [ipv6]
Hunks and backtrace stolen from a patch by Stephen Hemminger.
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tmp_prefered_lft is an offset to ifp->tstamp, not now. Therefore
age needs to be added to the condition.
Age calculation in ipv6_create_tempaddr is different from the one
in addrconf_verify and doesn't consider ADDRCONF_TIMER_FUZZ_MINUS.
This can cause age in ipv6_create_tempaddr to be less than the one
in addrconf_verify and therefore unnecessary temporary address to
be generated.
Use age calculation as in addrconf_modify to avoid this.
Signed-off-by: Heiner Kallweit <heiner.kallweit@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bug was reported by Steinar H. Gunderson and was introduced by commit
f7cb888633 ("sit/gre6: don't try to add the same route two times").
root@morgental:~# ip tunnel add foo mode gre remote 1.2.3.4 ttl 64
root@morgental:~# ip link set foo up mtu 1468
root@morgental:~# ip -6 route show dev foo
fe80::/64 proto kernel metric 256
but after the above commit, no such route shows up.
There is no link local route because dev->dev_addr is 0 (because local ipv4
address is 0), hence no link local address is configured.
In this scenario, the link local address is added manually: 'ip -6 addr add
fe80::1 dev foo' and because prefix is /128, no link local route is added by the
kernel.
Even if the right things to do is to add the link local address with a /64
prefix, we need to restore the previous behavior to avoid breaking userpace.
Reported-by: Steinar H. Gunderson <sesse@samfundet.no>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 25fb6ca4ed
"net IPv6 : Fix broken IPv6 routing table after loopback down-up"
allocates addrconf router for ipv6 address when lo device up.
but commit a881ae1f62
"ipv6:don't call addrconf_dst_alloc again when enable lo" breaks
this behavior.
Since the addrconf router is moved to the garbage list when
lo device down, we should release this router and rellocate
a new one for ipv6 address when lo device up.
This patch solves bug 67951 on bugzilla
https://bugzilla.kernel.org/show_bug.cgi?id=67951
change from v1:
use ip6_rt_put to repleace ip6_del_rt, thanks Hannes!
change code style, suggested by Sergei.
CC: Sabrina Dubroca <sd@queasysnail.net>
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_link_dev_addr sorts newly added addresses by scope in
ifp->addr_list. Smaller scope addresses are added to the tail of the
list. Use this fact to iterate in reverse over addr_list and break out
as soon as a higher scoped one showes up, so we can spare some cycles
on machines with lot's of addresses.
The ordering of the addresses is not relevant and we are more likely to
get the eui64 generated address with this change anyway.
Suggested-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
net/ipv4/tcp_metrics.c
Overlapping changes between the "don't create two tcp metrics objects
with the same key" race fix in net and the addition of the destination
address in the lookup key in net-next.
Minor overlapping changes in bnx2x driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 1ec047eb47 ("ipv6: introduce per-interface counter for
dad-completed ipv6 addresses") I build the detection of the first
operational link-local address much to complex. Additionally this code
now has a race condition.
Replace it with a much simpler variant, which just scans the address
list when duplicate address detection completes, to check if this is
the first valid link local address and send RS and MLD reports then.
Fixes: 1ec047eb47 ("ipv6: introduce per-interface counter for dad-completed ipv6 addresses")
Reported-by: Jiri Pirko <jiri@resnulli.us>
Cc: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Flavio Leitner <fbl@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the deletion/update of prefix routes when removing an
address. Now also consider IFA_F_NOPREFIXROUTE and if there is an address
present with this flag, to not cleanup the route. Instead, assume
that userspace is taking care of this route.
Also perform the same cleanup, when userspace changes an existing address
to add NOPREFIXROUTE (to an address that didn't have this flag). This is
done because when the address was added, a prefix route was created for it.
Since the user now wants to handle this route by himself, we cleanup this
route.
This cleanup of the route is not totally robust. There is no guarantee,
that the route we are about to delete was really the one added by the
kernel. This behavior does not change by the patch, and in practice it
should work just fine.
Signed-off-by: Thomas Haller <thaller@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding/modifying an IPv6 address, the userspace application needs
a way to suppress adding a prefix route. This is for example relevant
together with IFA_F_MANAGERTEMPADDR, where userspace creates autoconf
generated addresses, but depending on on-link, no route for the
prefix should be added.
Signed-off-by: Thomas Haller <thaller@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the net_random and net_srandom macros and replaces
them with direct calls to the prandom ones. As new commits only seem to
use prandom_u32 there is no use to keep them around.
This change makes it easier to grep for users of prandom_u32.
Signed-off-by: Aruna-Hewapathirane <aruna.hewapathirane@gmail.com>
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the past the IFA_PERMANENT flag indicated, that the valid and preferred
lifetime where ignored. Since change fad8da3e08 ("ipv6 addrconf: fix
preferred lifetime state-changing behavior while valid_lft is infinity")
we honour at least the preferred lifetime on those addresses. As such
the valid lifetime gets recalculated and updated to 0.
If loopback address is added manually this problem does not occur.
Also if NetworkManager manages IPv6, those addresses will get added via
inet6_rtm_newaddr and thus will have a correct lifetime, too.
Reported-by: François-Xavier Le Bail <fx.lebail@yahoo.com>
Reported-by: Damien Wyart <damien.wyart@gmail.com>
Fixes: fad8da3e08 ("ipv6 addrconf: fix preferred lifetime state-changing behavior while valid_lft is infinity")
Cc: Yasushi Asano <yasushi.asano@jp.fujitsu.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
It does not make sense to create an anycast address for an /128-prefix.
Suppress it.
As 32019e651c ("ipv6: Do not leave router anycast address for /127
prefixes.") shows we also may not leave them, because we could accidentally
remove an anycast address the user has allocated or got added via another
prefix.
Cc: François-Xavier Le Bail <fx.lebail@yahoo.com>
Cc: Thomas Haller <thaller@redhat.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a problem with setting the lifetime of an IPv6
address. When setting preferred_lft to a value not zero or
infinity, while valid_lft is infinity(0xffffffff) preferred
lifetime is set to forever and does not update. Therefore
preferred lifetime never becomes deprecated. valid lifetime
and preferred lifetime should be set independently, even if
valid lifetime is infinity, preferred lifetime must expire
correctly (meaning it must eventually become deprecated)
Signed-off-by: Yasushi Asano <yasushi.asano@jp.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function __rtnl_af_register is never called outside this
code, and the return value is always 0.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since addrconf_get_prefix_route inputs the address prefix to fib6_locate,
which does not uses the data which is out of the prefix_len length,
so do not need to use ipv6_addr_prefix to get address prefix.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to be able to see changes to proxy NDP status on a per
interface basis via netlink (analog to proxy_arp).
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Turned out that applications like ifconfig do not handle the change.
So revert ifa_flag format back to 2-letter hex value.
Introduced by:
commit 479840ffdb
"ipv6 addrconf: extend ifa_flags to u32"
Reported-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Tested-by: FLorent Fourcot <florent.fourcot@enst-bretagne.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the behaviour similar to ipv4. This will allow user to set sysctl
default neigh param values and these values will be respected even by
devices registered before (that ones what do not have address set yet).
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the neigh param members to an array. This allows easier
manipulation which will be needed later on to provide better management of
default values.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creating an address with this flag set will result in kernel taking care
of temporary addresses in the same way as if the address was created by
kernel itself (after RA receive). This allows userspace applications
implementing the autoconfiguration (NetworkManager for example) to
implement ipv6 addresses privacy.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Thomas Haller <thaller@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no more space in u8 ifa_flags. So do what davem suffested and
add another netlink attr called IFA_FLAGS for carry more flags.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Thomas Haller <thaller@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Mostly these are fixes for fallout due to merge window changes, as
well as cures for problems that have been with us for a much longer
period of time"
1) Johannes Berg noticed two major deficiencies in our genetlink
registration. Some genetlink protocols we passing in constant
counts for their ops array rather than something like
ARRAY_SIZE(ops) or similar. Also, some genetlink protocols were
using fixed IDs for their multicast groups.
We have to retain these fixed IDs to keep existing userland tools
working, but reserve them so that other multicast groups used by
other protocols can not possibly conflict.
In dealing with these two problems, we actually now use less state
management for genetlink operations and multicast groups.
2) When configuring interface hardware timestamping, fix several
drivers that simply do not validate that the hwtstamp_config value
is one the driver actually supports. From Ben Hutchings.
3) Invalid memory references in mwifiex driver, from Amitkumar Karwar.
4) In dev_forward_skb(), set the skb->protocol in the right order
relative to skb_scrub_packet(). From Alexei Starovoitov.
5) Bridge erroneously fails to use the proper wrapper functions to make
calls to netdev_ops->ndo_vlan_rx_{add,kill}_vid. Fix from Toshiaki
Makita.
6) When detaching a bridge port, make sure to flush all VLAN IDs to
prevent them from leaking, also from Toshiaki Makita.
7) Put in a compromise for TCP Small Queues so that deep queued devices
that delay TX reclaim non-trivially don't have such a performance
decrease. One particularly problematic area is 802.11 AMPDU in
wireless. From Eric Dumazet.
8) Fix crashes in tcp_fastopen_cache_get(), we can see NULL socket dsts
here. Fix from Eric Dumzaet, reported by Dave Jones.
9) Fix use after free in ipv6 SIT driver, from Willem de Bruijn.
10) When computing mergeable buffer sizes, virtio-net fails to take the
virtio-net header into account. From Michael Dalton.
11) Fix seqlock deadlock in ip4_datagram_connect() wrt. statistic
bumping, this one has been with us for a while. From Eric Dumazet.
12) Fix NULL deref in the new TIPC fragmentation handling, from Erik
Hugne.
13) 6lowpan bit used for traffic classification was wrong, from Jukka
Rissanen.
14) macvlan has the same issue as normal vlans did wrt. propagating LRO
disabling down to the real device, fix it the same way. From Michal
Kubecek.
15) CPSW driver needs to soft reset all slaves during suspend, from
Daniel Mack.
16) Fix small frame pacing in FQ packet scheduler, from Eric Dumazet.
17) The xen-netfront RX buffer refill timer isn't properly scheduled on
partial RX allocation success, from Ma JieYue.
18) When ipv6 ping protocol support was added, the AF_INET6 protocol
initialization cleanup path on failure was borked a little. Fix
from Vlad Yasevich.
19) If a socket disconnects during a read/recvmsg/recvfrom/etc that
blocks we can do the wrong thing with the msg_name we write back to
userspace. From Hannes Frederic Sowa. There is another fix in the
works from Hannes which will prevent future problems of this nature.
20) Fix route leak in VTI tunnel transmit, from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
genetlink: make multicast groups const, prevent abuse
genetlink: pass family to functions using groups
genetlink: add and use genl_set_err()
genetlink: remove family pointer from genl_multicast_group
genetlink: remove genl_unregister_mc_group()
hsr: don't call genl_unregister_mc_group()
quota/genetlink: use proper genetlink multicast APIs
drop_monitor/genetlink: use proper genetlink multicast APIs
genetlink: only pass array to genl_register_family_with_ops()
tcp: don't update snd_nxt, when a socket is switched from repair mode
atm: idt77252: fix dev refcnt leak
xfrm: Release dst if this dst is improper for vti tunnel
netlink: fix documentation typo in netlink_set_err()
be2net: Delete secondary unicast MAC addresses during be_close
be2net: Fix unconditional enabling of Rx interface options
net, virtio_net: replace the magic value
ping: prevent NULL pointer dereference on write to msg_name
bnx2x: Prevent "timeout waiting for state X"
bnx2x: prevent CFC attention
bnx2x: Prevent panic during DMAE timeout
...
addrconf_add_linklocal() already adds the link local route, so there is no
reason to add it before calling this function.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link local address was added to a sit interface, the corresponding route
was not configured. This breaks routing protocols that use the link local
address, like OSPFv3.
To ease the code reading, I remove sit_route_add(), which only adds v4 mapped
routes, and add this kind of route directly in sit_add_v4_addrs(). Thus link
local and v4 mapped routes are configured in the same place.
Reported-by: Li Hongjun <hongjun.li@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the local IPv4 endpoint is wilcard (0.0.0.0), the prefix length is
correctly set, ie 64 if the address is a link local one or 96 if the address is
a v4 mapped one.
But when the local endpoint is specified, the prefix length is set to 128 for
both kind of address. This patch fix this wrong prefix length.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull core locking changes from Ingo Molnar:
"The biggest changes:
- add lockdep support for seqcount/seqlocks structures, this
unearthed both bugs and required extra annotation.
- move the various kernel locking primitives to the new
kernel/locking/ directory"
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
block: Use u64_stats_init() to initialize seqcounts
locking/lockdep: Mark __lockdep_count_forward_deps() as static
lockdep/proc: Fix lock-time avg computation
locking/doc: Update references to kernel/mutex.c
ipv6: Fix possible ipv6 seqlock deadlock
cpuset: Fix potential deadlock w/ set_mems_allowed
seqcount: Add lockdep functionality to seqcount/seqlock structures
net: Explicitly initialize u64_stats_sync structures for lockdep
locking: Move the percpu-rwsem code to kernel/locking/
locking: Move the lglocks code to kernel/locking/
locking: Move the rwsem code to kernel/locking/
locking: Move the rtmutex code to kernel/locking/
locking: Move the semaphore core to kernel/locking/
locking: Move the spinlock code to kernel/locking/
locking: Move the lockdep code to kernel/locking/
locking: Move the mutex code to kernel/locking/
hung_task debugging: Add tracepoint to report the hang
x86/locking/kconfig: Update paravirt spinlock Kconfig description
lockstat: Report avg wait and hold times
lockdep, x86/alternatives: Drop ancient lockdep fixup message
...
In order to enable lockdep on seqcount/seqlock structures, we
must explicitly initialize any locks.
The u64_stats_sync structure, uses a seqcount, and thus we need
to introduce a u64_stats_init() function and use it to initialize
the structure.
This unfortunately adds a lot of fairly trivial initialization code
to a number of drivers. But the benefit of ensuring correctness makes
this worth while.
Because these changes are required for lockdep to be enabled, and the
changes are quite trivial, I've not yet split this patch out into 30-some
separate patches, as I figured it would be better to get the various
maintainers thoughts on how to best merge this change along with
the seqcount lockdep enablement.
Feedback would be appreciated!
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: James Morris <jmorris@namei.org>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Roger Luethi <rl@hellgate.ch>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Simon Horman <horms@verge.net.au>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Wensong Zhang <wensong@linux-vs.org>
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/1381186321-4906-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The code for privacy extentions is very mature, and making it
configurable only gives marginal memory/code savings in exchange
for obfuscation and hard to read code via CPP ifdef'ery.
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the scenario where an IPv6 router is advertising a fixed
preferred_lft of 1800 seconds, while the valid_lft begins at 3600
seconds and counts down in realtime.
A client should reset its preferred_lft to 1800 every time the RA is
received, but a bug is causing Linux to ignore the update.
The core problem is here:
if (prefered_lft != ifp->prefered_lft) {
Note that ifp->prefered_lft is an offset, so it doesn't decrease over
time. Thus, the comparison is always (1800 != 1800), which fails to
trigger an update.
The most direct solution would be to compute a "stored_prefered_lft",
and use that value in the comparison. But I think that trying to filter
out unnecessary updates here is a premature optimization. In order for
the filter to apply, both of these would need to hold:
- The advertised valid_lft and preferred_lft are both declining in
real time.
- No clock skew exists between the router & client.
So in this patch, I've set "update_lft = 1" unconditionally, which
allows the surrounding code to be greatly simplified.
Signed-off-by: Paul Marks <pmarks@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a router is doing DNAT for 6to4/6rd packets the latest
anti-spoofing commit 218774dc ("ipv6: add anti-spoofing checks for
6to4 and 6rd") will drop them because the IPv6 address embedded does
not match the IPv4 destination. This patch will allow them to pass by
testing if we have an address that matches on 6to4/6rd interface. I
have been hit by this problem using Fedora and IPV6TO4_IPV4ADDR.
Also, log the dropped packets (with rate limit).
Signed-off-by: Catalin(ux) M. BOIE <catab@embedromix.ro>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
net/bridge/br_multicast.c
net/ipv6/sit.c
The conflicts were minor:
1) sit.c changes overlap with change to ip_tunnel_xmit() signature.
2) br_multicast.c had an overlap between computing max_delay using
msecs_to_jiffies and turning MLDV2_MRC() into an inline function
with a name using lowercase instead of uppercase letters.
3) stmmac had two overlapping changes, one which conditionally allocated
and hooked up a dma_cfg based upon the presence of the pbl OF property,
and another one handling store-and-forward DMA made. The latter of
which should not go into the new of_find_property() basic block.
Signed-off-by: David S. Miller <davem@davemloft.net>
This two-liner removes max_addresses variable which is now unecessary related
to patch [ipv6: remove max_addresses check from ipv6_create_tempaddr].
Signed-off-by: Petr Holasek <pholasek@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in6_dev_put() will be needed by vxlan module, so is
in6_dev_finish_destroy().
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because vxlan module will call ip6_dst_lookup() in TX path,
which will hold write lock. So we have to release this write lock
before calling ndisc_send_rs(), otherwise could deadlock.
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is needed by vxlan module. Noticed by Mike.
Cc: Mike Rapoport <mike.rapoport@ravellosystems.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements RFC6980: Drop fragmented ndisc packets by
default. If a fragmented ndisc packet is received the user is informed
that it is possible to disable the check.
Cc: Fernando Gont <fernando@gont.com.ar>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/iwlwifi/pcie/trans.c
include/linux/inetdevice.h
The inetdevice.h conflict involves moving the IPV4_DEVCONF values
into a UAPI header, overlapping additions of some new entries.
The iwlwifi conflict is a context overlap.
Signed-off-by: David S. Miller <davem@davemloft.net>
When an Xin6 tunnel is set up, we check other netdevices to inherit the link-
local address. If none is available, the interface will not have any link-local
address. RFC4862 expects that each interface has a link local address.
Now than this kind of tunnels supports x-netns, it's easy to fall in this case
(by creating the tunnel in a netns where ethernet interfaces stand and then
moving it to a other netns where no ethernet interface is available).
RFC4291, Appendix A suggests two methods: the first is the one currently
implemented, the second is to generate a unique identifier, so that we can
always generate the link-local address. Let's use eth_random_addr() to generate
this interface indentifier.
I remove completly the previous method, hence for the whole life of the
interface, the link-local address remains the same (previously, it depends on
which ethernet interfaces were up when the tunnel interface was set up).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit df8372ca74.
These changes are buggy and make unintended semantic changes
to ip6_tnl_add_linklocal().
Signed-off-by: David S. Miller <davem@davemloft.net>
ERROR: code indent should use tabs where possible: fix 2.
ERROR: do not use assignment in if condition: fix 5.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just follow the Joe Perches's opinion, it is a better way to fix the
style errors.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because of the max_addresses check attackers were able to disable privacy
extensions on an interface by creating enough autoconfigured addresses:
<http://seclists.org/oss-sec/2012/q4/292>
But the check is not actually needed: max_addresses protects the
kernel to install too many ipv6 addresses on an interface and guards
addrconf_prefix_rcv to install further addresses as soon as this limit
is reached. We only generate temporary addresses in direct response of
a new address showing up. As soon as we filled up the maximum number of
addresses of an interface, we stop installing more addresses and thus
also stop generating more temp addresses.
Even if the attacker tries to generate a lot of temporary addresses
by announcing a prefix and removing it again (lifetime == 0) we won't
install more temp addresses, because the temporary addresses do count
to the maximum number of addresses, thus we would stop installing new
autoconfigured addresses when the limit is reached.
This patch fixes CVE-2013-0343 (but other layer-2 attacks are still
possible).
Thanks to Ding Tianhong to bring this topic up again.
Cc: Ding Tianhong <dingtianhong@huawei.com>
Cc: George Kargiotakis <kargig@void.gr>
Cc: P J P <ppandit@redhat.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit cab70040df ("net: igmp:
Reduce Unsolicited report interval to 1s when using IGMPv3") and
2690048c01 ("net: igmp: Allow user-space
configuration of igmp unsolicited report interval") by William Manley made
igmp unsolicited report intervals configurable per interface and corrected
the interval of unsolicited igmpv3 report messages resendings to 1s.
Same needs to be done for IPv6:
MLDv1 (RFC2710 7.10.): 10 seconds
MLDv2 (RFC3810 9.11.): 1 second
Both intervals are configurable via new procfs knobs
mldv1_unsolicited_report_interval and mldv2_unsolicited_report_interval.
(also added .force_mld_version to ipv6_devconf_dflt to bring structs in
line without semantic changes)
v2:
a) Joined documentation update for IPv4 and IPv6 MLD/IGMP
unsolicited_report_interval procfs knobs.
b) incorporate stylistic feedback from William Manley
v3:
a) add new DEVCONF_* values to the end of the enum (thanks to David
Miller)
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: William Manley <william.manley@youview.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Server Client
2001:1::803/64 <-> 2001:1::805/64
2001:2::804/64 <-> 2001:2::806/64
Server side fib binary tree looks like this:
(2001:/64)
/
/
ffff88002103c380
/ \
(2) / \
(2001::803/128) ffff880037ac07c0
/ \
/ \ (3)
ffff880037ac0640 (2001::806/128)
/ \
(1) / \
(2001::804/128) (2001::805/128)
Delete 2001::804/64 won't cause prefix route deleted as well as rt in (3)
destinate to 2001::806 with source address as 2001::804/64. That's because
2001::803/64 is still alive, which make onlink=1 in ipv6_del_addr, this is
where the substantial difference between same prefix configuration and
different prefix configuration :) So packet are still transmitted out to
2001::806 with source address as 2001::804/64.
So bump genid will clear rt in (3), and up layer protocol will eventually
find the right one for themselves.
This problem arised from the discussion in here:
http://marc.info/?l=linux-netdev&m=137404469219410&w=4
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a race in IPv6 automatic addess assignment. The address is created
with zero lifetime when it's added to various address lists. Before it gets
assigned the correct lifetime, there's a window where a new address may be
configured. This causes the semi-initiated address to be deleted in
addrconf_verify.
This was discovered as a reference leak caused by concurrent run of
__ipv6_ifa_notify for both RTM_NEWADDR and RTM_DELADDR with the same
address.
Fix this by setting the lifetime before the address is added to
inet6_addr_lst.
A few notes:
1. In addrconf_prefix_rcv, by setting update_lft to zero, the
if (update_lft) { ... } condition is no longer executed for newly
created addresses. This is okay, as the ifp fields are set in
ipv6_add_addr now and ipv6_ifa_notify is called (and has been called)
through addrconf_dad_start.
2. The removal of the whole block under ifp->lock in inet6_addr_add is okay,
too, as tstamp is initialized to jiffies in ipv6_add_addr.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
drivers/net/ethernet/renesas/sh_eth.c
net/ipv4/gre.c
The GRE conflict is between a bug fix (kfree_skb --> kfree_skb_list)
and the splitting of the gre.c code into seperate files.
The FEC conflict was two sets of changes adding ethtool support code
in an "!CONFIG_M5272" CPP protected block.
Finally the sh_eth.c conflict was between one commit add bits set
in the .eesr_err_check mask whilst another commit removed the
.tx_error_check member and assignments.
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC3590/RFC3810 specifies we should resend MLD reports as soon as a
valid link-local address is available.
We now use the valid_ll_addr_cnt to check if it is necessary to resend
a new report.
Changes since Flavio Leitner's version:
a) adapt for valid_ll_addr_cnt
b) resend first reports directly in the path and just arm the timer for
mc_qrv-1 resends.
Reported-by: Flavio Leitner <fleitner@redhat.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To reduce the number of unnecessary router solicitations, MLDv2 and IGMPv3
messages we need to track the number of valid (as in non-optimistic,
no-dad-failed and non-tentative) link-local addresses. Therefore, this
patch implements a valid_ll_addr_cnt in struct inet6_dev.
We now only emit router solicitations if the first link-local address
finishes duplicate address detection.
The changes for MLDv2 and IGMPv3 are in a follow-up patch.
While there, also simplify one if statement(one minor nit I made in one
of my previous patches):
if (!...)
do();
else
return;
<<into>>
if (...)
return;
do();
Cc: Flavio Leitner <fbl@redhat.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Cc: David Stevens <dlstevens@us.ibm.com>
Suggested-by: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new tokenized address gets installed we send out just one
router solicition. We should send out `rtr_solicits' in case one router
advertisment got lost.
So, rearm the timer as we do in addrconf_dad_complete.
Cc: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the tokenized ip address is re-set on an interface we depend on the
arrival of a new router advertisment to call addrconf_verify to clean
up the old address (which valid_lft is now set to 0). Old addresses can
linger around for a longer time if e.g. the source of router advertisments
vanishes.
So, call addrconf_verify immediately after setting the new tokenized
address to get rid of the old tokenized addresses.
Cc: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should check the return value of ipv6_get_lladdr in inet6_set_iftoken.
A possible situation, which could leave ll_addr unassigned is, when
the user removed her link-local address but a global scoped address was
already set. In this case the interface would still be IF_READY and not
dead. In that case the RS source address is some value from the stack.
v2: Daniel Borkmann noted a small indent inconstancy; no semantic
changes.
Cc: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Reviewed-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reason behind this change is that as soon as we delete
the last ipv6 address of an interface we also lose the
/proc/sys/net/ipv6/conf/<interface> directory. This seems to be a
usability problem for me.
I don't see any reason why we should shutdown ipv6 on that interface in
such cases.
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch splits the timers for duplicate address detection and router
solicitations apart. The router solicitations timer goes into inet6_dev
and the dad timer stays in inet6_ifaddr.
The reason behind this patch is to reduce the number of unneeded router
solicitations send out by the host if additional link-local addresses
are created. Currently we send out RS for every link-local address on
an interface.
If the RS timer fires we pick a source address with ipv6_get_lladdr. This
change could hurt people adding additional link-local addresses and
specifying these addresses in the radvd clients section because we
no longer guarantee that we use every ll address as source address in
router solicitations.
Cc: Flavio Leitner <fleitner@redhat.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: David Stevens <dlstevens@us.ibm.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reviewed-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is debug info, should at least be pr_debug(), but given
that this code is in upstream for two years, there is no
need to keep this debugging printk any more, so just remove it.
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we disable all of the net interfaces, and enable
un-lo interface before lo interface, we already allocated
the addrconf dst in ipv6_add_addr. So we shouldn't allocate
it again when we enable lo interface.
Otherwise the message below will be triggered.
unregister_netdevice: waiting for sit1 to become free. Usage count = 1
This problem is introduced by commit 25fb6ca4ed
"net IPv6 : Fix broken IPv6 routing table after loopback down-up"
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the uses of this unnecessary typedef.
Done via perl script:
$ git grep --name-only -w ctl_table net | \
xargs perl -p -i -e '\
sub trim { my ($local) = @_; $local =~ s/(^\s+|\s+$)//g; return $local; } \
s/\b(?<!struct\s)ctl_table\b(\s*\*\s*|\s+\w+)/"struct ctl_table " . trim($1)/ge'
Reflow the modified lines that now exceed 80 columns.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 25fb6ca4ed
"net IPv6 : Fix broken IPv6 routing table after loopback down-up"
forgot to assign rt6_info to the inet6_ifaddr.
When disable the net device, the rt6_info which allocated
in init_loopback will not be destroied in __ipv6_ifa_notify.
This will trigger the waring message below
[23527.916091] unregister_netdevice: waiting for tap0 to become free. Usage count = 1
Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 351638e7de (net: pass info struct via netdevice notifier)
breaks booting of my KVM guest, this is due to we still forget to pass
struct netdev_notifier_info in several places. This patch completes it.
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, only net_device * could be passed along with netdevice notifier
event. This patch provides a possibility to pass custom structure
able to provide info that event listener needs to know.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
v2->v3: fix typo on simeth
shortened dev_getter
shortened notifier_info struct name
v1->v2: fix notifier_call parameter in call_netdevice_notifier()
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting https://bugzilla.netfilter.org/show_bug.cgi?id=812:
[ ip6tables -m addrtype ]
When I tried to use in the nat/PREROUTING it messes up the
routing cache even if the rule didn't matched at all.
[..]
If I remove the --limit-iface-in from the non-working scenario, so just
use the -m addrtype --dst-type LOCAL it works!
This happens when LOCAL type matching is requested with --limit-iface-in,
and the default ipv6 route is via the interface the packet we test
arrived on.
Because xt_addrtype uses ip6_route_output, the ipv6 routing implementation
creates an unwanted cached entry, and the packet won't make it to the
real/expected destination.
Silently ignoring --limit-iface-in makes the routing work but it breaks
rule matching (--dst-type LOCAL with limit-iface-in is supposed to only
match if the dst address is configured on the incoming interface;
without --limit-iface-in it will match if the address is reachable
via lo).
The test should call ipv6_chk_addr() instead. However, this would add
a link-time dependency on ipv6.
There are two possible solutions:
1) Revert the commit that moved ipt_addrtype to xt_addrtype,
and put ipv6 specific code into ip6t_addrtype.
2) add new "nf_ipv6_ops" struct to register pointers to ipv6 functions.
While the former might seem preferable, Pablo pointed out that there
are more xt modules with link-time dependeny issues regarding ipv6,
so lets go for 2).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ipv6_addr_type(&addr)&IPV6_ADDR_SCOPE_MASK could be replaced
by ipv6_addr_scope(), which is slightly faster.
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_addr_any() is a faster way to determine if an addr
is ipv6 any addr, no need to compute the addr type.
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of peer address for IPv6. For example, it is
possible to specify the remote end of a 6inY tunnel.
This was already possible in IPv4:
ip addr add ip1 peer ip2 dev dev1
The peer address is specified with IFA_ADDRESS and the local address with
IFA_LOCAL (like explained in include/uapi/linux/if_addr.h).
Note that the API is not changed, because before this patch, it was not
possible to specify two different addresses in IFA_LOCAL and IFA_REMOTE.
There is a small change for the dump: if the peer is different from ::,
IFA_ADDRESS will contain the peer address instead of the local address.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
drivers/net/ethernet/intel/igb/igb_main.c
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
include/net/scm.h
net/batman-adv/routing.c
net/ipv4/tcp_input.c
The e{uid,gid} --> {uid,gid} credentials fix conflicted with the
cleanup in net-next to now pass cred structs around.
The be2net driver had a bug fix in 'net' that overlapped with the VLAN
interface changes by Patrick McHardy in net-next.
An IGB conflict existed because in 'net' the build_skb() support was
reverted, and in 'net-next' there was a comment style fix within that
code.
Several batman-adv conflicts were resolved by making sure that all
calls to batadv_is_my_mac() are changed to have a new bat_priv first
argument.
Eric Dumazet's TS ECR fix in TCP in 'net' conflicted with the F-RTO
rewrite in 'net-next', mostly overlapping changes.
Thanks to Stephen Rothwell and Antonio Quartulli for help with several
of these merge resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal