This makes use of bt_skb_sendmsg instead of allocating a different
buffer to be used with memcpy_from_msg which cause one extra copy.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This splits the msft_do_{open/close} to msft_do_{open/close} and
msft_{register/unregister}. With this change it is possible to retain
the MSFT extension info irrespective of controller power on/off state.
This helps bluetoothd to report correct 'supported features' of the
controller to the D-Bus clients event if the controller is off. It also
re-reads the MSFT info upon every msft_do_open().
The following test steps were performed.
1. Boot the test device and verify the MSFT support debug log in syslog.
2. Power off the controller and read the 'supported features', power on
and read again.
3. Restart the bluetoothd and verify the 'supported features' value.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently usb tranport is not allowed to suspend when SCO over
HCI tranport is active.
This patch shall enable the usb tranport to suspend when SCO
link use non-HCI transport.
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Allow user level process to enable / disable codec offload
feature through mgmt interface. By default offload codec feature
is disabled.
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In Enhanced_Setup_Synchronous_Command, add support for msbc
coding format
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For HFP offload use case, codec needs to be configured
before opening SCO connection. This patch sends
HCI_CONFIGURE_DATA_PATH command to configure doec before
opening SCO connection.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch allows user space to set the codec that needs to
be used for HFP offload use case. The codec details are cached and
the controller is configured before opening the SCO connection.
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add BT_CODEC option for getsockopt systemcall to get the details
of offload codecs supported over SCO socket
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Move reading of supported local codecs into a separate init function,
query codecs capabilities and cache the data
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Before freeing struct sco_conn, all delayed timeout work should be
cancelled. Otherwise, sco_sock_timeout could potentially use the
sco_conn after it has been freed.
Additionally, sco_conn.timeout_work should be initialized when the
connection is allocated, not when the channel is added. This is
because an sco_conn can create channels with multiple sockets over its
lifetime, which happens if sockets are released but the connection
isn't deleted.
Fixes: ba316be1b6 ("Bluetooth: schedule SCO timeouts with delayed_work")
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In sco_conn_del, conn->sk is read while holding on to the
sco_conn.lock to avoid races with a socket that could be released
concurrently.
However, in between unlocking sco_conn.lock and calling sock_hold,
it's possible for the socket to be freed, which would cause a
use-after-free write when sock_hold is finally called.
To fix this, the reference count of the socket should be increased
while the sco_conn.lock is still held.
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Here is the "big" set of tty/serial driver patches for 5.15-rc1
Nothing major in here at all, just some driver updates and more cleanups
on old tty apis and code that needed it that includes:
- tty.h cleanup of things that didn't belong in it
- other tty cleanups by Jiri
- driver cleanups
- rs485 support added to amba-pl011 driver
- dts updates
- stm32 serial driver updates
- other minor fixes and driver updates
All have been in linux-next for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS9/lg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylZNwCggKViEViSGqJFIafAZZjmI3Nt6tUAoMkRlhcd
n1MS3snS0Sq+7BdJs37M
=GyxP
-----END PGP SIGNATURE-----
Merge tag 'tty-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the "big" set of tty/serial driver patches for 5.15-rc1
Nothing major in here at all, just some driver updates and more
cleanups on old tty apis and code that needed it that includes:
- tty.h cleanup of things that didn't belong in it
- other tty cleanups by Jiri
- driver cleanups
- rs485 support added to amba-pl011 driver
- dts updates
- stm32 serial driver updates
- other minor fixes and driver updates
All have been in linux-next for a while with no reported problems"
* tag 'tty-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (83 commits)
tty: serial: uartlite: Use read_poll_timeout for a polling loop
tty: serial: uartlite: Use constants in early_uartlite_putc
tty: Fix data race between tiocsti() and flush_to_ldisc()
serial: vt8500: Use of_device_get_match_data
serial: tegra: Use of_device_get_match_data
serial: 8250_ingenic: Use of_device_get_match_data
tty: serial: linflexuart: Remove redundant check to simplify the code
tty: serial: fsl_lpuart: do software reset for imx7ulp and imx8qxp
tty: serial: fsl_lpuart: enable two stop bits for lpuart32
tty: serial: fsl_lpuart: fix the wrong mapbase value
mxser: use semi-colons instead of commas
tty: moxa: use semi-colons instead of commas
tty: serial: fsl_lpuart: check dma_tx_in_progress in tx dma callback
tty: replace in_irq() with in_hardirq()
serial: sh-sci: fix break handling for sysrq
serial: stm32: use devm_platform_get_and_ioremap_resource()
serial: stm32: use the defined variable to simplify code
Revert "arm pl011 serial: support multi-irq request"
tty: serial: samsung: Add Exynos850 SoC data
tty: serial: samsung: Fix driver data macros style
...
When connecting to a device using an RPA if the address has been
resolved by the controller (types 0x02 and 0x03) the identity address
shall be used as the actual RPA in the advertisement won't be visible
to the host.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Address types ADDR_LE_DEV_PUBLIC_RESOLVED and
ADDR_LE_DEV_RANDOM_RESOLVED shall be converted to ADDR_LE_PUBLIC and
ADDR_LE_RANDOM repectively since they are not safe to be used beyond
the scope of the events themselves.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When disconnecting the advertising shall be re-enabled only when the
connection role is slave/peripheral as the central role use advertising
to connect it could end up enabling the instance 0x00 if there are other
advertising instances.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The sco_send_frame() also takes lock_sock() during memcpy_from_msg()
call that may be endlessly blocked by a task with userfaultd
technique, and this will result in a hung task watchdog trigger.
Just like the similar fix for hci_sock_sendmsg() in commit
92c685dc5de0 ("Bluetooth: reorganize functions..."), this patch moves
the memcpy_from_msg() out of lock_sock() for addressing the hang.
This should be the last piece for fixing CVE-2021-3640 after a few
already queued fixes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch allows a user space process to enable/disable the quality
report events dynamically through the set experimental feature mgmt
interface.
Since the quality report feature needs to invoke the callback function
provided by the driver, i.e., hdev->set_quality_report, a valid
controller index is required.
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch refactors the set_exp_feature with a feature table
consisting of UUIDs and the corresponding callback functions.
In this way, a new experimental feature setting function can be
simply added with its UUID and callback function.
Signed-off-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Legacy (v2.0) controllers do not support Extended OOB Data used by SSP.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Since userfaultfd mechanism allows sleeping with kernel lock held,
avoiding page fault with kernel lock held where possible will make
the module more robust. This patch just brings memcpy_from_msg() calls
to out of sock lock.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
- Add support for Foxconn Mediatek Chip
- Add support for LG LGSBWAC92/TWCM-K505D
- hci_h5 flow control fixes and suspend support
- Switch to use lock_sock for SCO and RFCOMM
- Various fixes for extended advertising
- Reword Intel's setup on btusb unifying the supported generations
-----BEGIN PGP SIGNATURE-----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=INb2
-----END PGP SIGNATURE-----
Merge tag 'for-net-next-2021-08-19' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Add support for Foxconn Mediatek Chip
- Add support for LG LGSBWAC92/TWCM-K505D
- hci_h5 flow control fixes and suspend support
- Switch to use lock_sock for SCO and RFCOMM
- Various fixes for extended advertising
- Reword Intel's setup on btusb unifying the supported generations
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
hci_error_reset() return without calling hci_dev_do_open() when
hci_dev_do_close() return error value which is not 0.
Also, hci_dev_close() return hci_dev_do_close() function's return
value.
But, hci_dev_do_close() return always 0 even if hdev->shutdown
return error value. So, fix hci_dev_do_close() to save and return
the return value of the hdev->shutdown when it is called.
Signed-off-by: Kangmin Park <l4stpr0gr4m@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Syzbot hit "task hung" bug in hci_req_sync(). The problem was in
unreasonable huge inquiry timeout passed from userspace.
Fix it by adding sanity check for timeout value to hci_inquiry().
Since hci_inquiry() is the only user of hci_req_sync() with user
controlled timeout value, it makes sense to check timeout value in
hci_inquiry() and don't touch hci_req_sync().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-and-tested-by: syzbot+be2baed593ea56c6a84c@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After gaining __alloc_size hints, GCC thinks it can reach a memcpy()
with eir_len == 0 (since it can't see into the rewrite of status).
Instead, check eir_len == 0, avoiding this future warning:
In function 'eir_append_data',
inlined from 'read_local_oob_ext_data_complete' at net/bluetooth/mgmt.c:7210:12:
./include/linux/fortify-string.h:54:29: warning: '__builtin_memcpy' offset 5 is out of the bounds [0, 3] [-Warray-bounds]
...
net/bluetooth/hci_request.h:133:2: note: in expansion of macro 'memcpy'
133 | memcpy(&eir[eir_len], data, data_len);
| ^~~~~~
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-bluetooth@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For NOP command, need to cancel work scheduled on cmd_timer,
on receiving command status or commmand complete event.
Below use case might lead to race condition multiple when NOP
commands are queued sequentially:
hci_cmd_work() {
if (atomic_read(&hdev->cmd_cnt) {
.
.
.
atomic_dec(&hdev->cmd_cnt);
hci_send_frame(hdev,...);
schedule_delayed_work(&hdev->cmd_timer,...);
}
}
On receiving event for first NOP, the work scheduled on hdev->cmd_timer
is not cancelled and second NOP is dequeued and sent to controller.
While waiting for an event for second NOP command, work scheduled on
cmd_timer for the first NOP can get scheduled, resulting in sending third
NOP command (sending back to back NOP commands). This might
cause issues at controller side (like memory overrun, controller going
unresponsive) resulting in hci tx timeouts, hardware errors etc.
The fix to this issue is to cancel the delayed work scheduled on
cmd_timer on receiving command status or command complete event for
NOP command (this patch handles NOP command same as any other SIG
command).
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Acked-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This stores the advertising handle/instance into hci_conn so it is
accessible when re-enabling the advertising once disconnected.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
LE Enhanced Connection Complete contains the Local RPA used in the
connection which must be used when set otherwise there could problems
when pairing since the address used by the remote stack could be the
Local RPA:
BLUETOOTH CORE SPECIFICATION Version 5.2 | Vol 4, Part E
page 2396
'Resolvable Private Address being used by the local device for this
connection. This is only valid when the Own_Address_Type (from the
HCI_LE_Create_Connection, HCI_LE_Set_Advertising_Parameters,
HCI_LE_Set_Extended_Advertising_Parameters, or
HCI_LE_Extended_Create_Connection commands) is set to 0x02 or
0x03, and the Controller generated a resolvable private address for the
local device using a non-zero local IRK. For other Own_Address_Type
values, the Controller shall return all zeros.'
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit 0ea9fd001a ("Bluetooth: Shutdown controller after workqueues
are flushed or cancelled") introduced a regression that makes mtkbtsdio
driver stops working:
[ 36.593956] Bluetooth: hci0: Firmware already downloaded
[ 46.814613] Bluetooth: hci0: Execution of wmt command timed out
[ 46.814619] Bluetooth: hci0: Failed to send wmt func ctrl (-110)
The shutdown callback depends on the result of hdev->rx_work, so we
should call it before flushing rx_work:
-> btmtksdio_shutdown()
-> mtk_hci_wmt_sync()
-> __hci_cmd_send()
-> wait for BTMTKSDIO_TX_WAIT_VND_EVT gets cleared
-> btmtksdio_recv_event()
-> hci_recv_frame()
-> queue_work(hdev->workqueue, &hdev->rx_work)
-> clears BTMTKSDIO_TX_WAIT_VND_EVT
So move the shutdown callback before flushing TX/RX queue to resolve the
issue.
Reported-and-tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Fixes: 0ea9fd001a ("Bluetooth: Shutdown controller after workqueues are flushed or cancelled")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In commit 4e1a720d03 ("Bluetooth: avoid killing an already killed
socket"), a check was added to sco_sock_kill to skip killing a socket
if the SOCK_DEAD flag was set.
This was done after a trace for a use-after-free bug showed that the
same sock pointer was being killed twice.
Unfortunately, this check prevents sco_sock_kill from running on any
socket. sco_sock_kill kills a socket only if it's zapped and orphaned,
however sock_orphan announces that the socket is dead before detaching
it. i.e., orphaned sockets have the SOCK_DEAD flag set.
To fix this, we remove the check for SOCK_DEAD, and avoid repeated
calls to sco_sock_kill by removing incorrect calls in:
1. sco_sock_timeout. The socket should not be killed on timeout as
further processing is expected to be done. For example,
sco_sock_connect sets the timer then waits for the socket to be
connected or for an error to be returned.
2. sco_conn_del. This function should clean up resources for the
connection, but the socket itself should be cleaned up in
sco_sock_release.
3. sco_sock_close. Calls to sco_sock_close in sco_sock_cleanup_listen
and sco_sock_release are followed by sco_sock_kill. Hence the
duplicated call should be removed.
Fixes: 4e1a720d03 ("Bluetooth: avoid killing an already killed socket")
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Other than rfcomm_sk_state_change and rfcomm_connect_ind, functions in
RFCOMM use lock_sock to lock the socket.
Since bh_lock_sock and spin_lock_bh do not provide synchronization
with lock_sock, these calls should be changed to lock_sock.
This is now safe to do because packet processing is now done in a
workqueue instead of a tasklet, so bh_lock_sock/spin_lock_bh are no
longer necessary to synchronise between user contexts and SOFTIRQ
processing.
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Currently, calls to sco_sock_set_timer are made under the locked
socket, but this does not apply to all calls to sco_sock_clear_timer.
Both sco_sock_{set,clear}_timer should be serialized by lock_sock to
prevent unexpected concurrent clearing/setting of timers.
Additionally, since sco_pi(sk)->conn is only cleared under the locked
socket, this change allows us to avoid races between
sco_sock_clear_timer and the call to kfree(conn) in sco_conn_del.
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Since sco_sock_timeout is now scheduled using delayed work, it is no
longer run in SOFTIRQ context. Hence bh_lock_sock is no longer
necessary in SCO to synchronise between user contexts and SOFTIRQ
processing.
As such, calls to bh_lock_sock should be replaced with lock_sock to
synchronize with other concurrent processes that use lock_sock.
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
struct sock.sk_timer should be used as a sock cleanup timer. However,
SCO uses it to implement sock timeouts.
This causes issues because struct sock.sk_timer's callback is run in
an IRQ context, and the timer callback function sco_sock_timeout takes
a spin lock on the socket. However, other functions such as
sco_conn_del and sco_conn_ready take the spin lock with interrupts
enabled.
This inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} lock usage could
lead to deadlocks as reported by Syzbot [1]:
CPU0
----
lock(slock-AF_BLUETOOTH-BTPROTO_SCO);
<Interrupt>
lock(slock-AF_BLUETOOTH-BTPROTO_SCO);
To fix this, we use delayed work to implement SCO sock timouts
instead. This allows us to avoid taking the spin lock on the socket in
an IRQ context, and corrects the misuse of struct sock.sk_timer.
As a note, cancel_delayed_work is used instead of
cancel_delayed_work_sync in sco_sock_set_timer and
sco_sock_clear_timer to avoid a deadlock. In the future, the call to
bh_lock_sock inside sco_sock_timeout should be changed to lock_sock to
synchronize with other functions using lock_sock. However, since
sco_sock_set_timer and sco_sock_clear_timer are sometimes called under
the locked socket (in sco_connect and __sco_sock_close),
cancel_delayed_work_sync might cause them to sleep until an
sco_sock_timeout that has started finishes running. But
sco_sock_timeout would also sleep until it can grab the lock_sock.
Using cancel_delayed_work is fine because sco_sock_timeout does not
change from run to run, hence there is no functional difference
between:
1. waiting for a timeout to finish running before scheduling another
timeout
2. scheduling another timeout while a timeout is running.
Link: https://syzkaller.appspot.com/bug?id=9089d89de0502e120f234ca0fc8a703f7368b31e [1]
Reported-by: syzbot+2f6d7c28bb4bf7e82060@syzkaller.appspotmail.com
Tested-by: syzbot+2f6d7c28bb4bf7e82060@syzkaller.appspotmail.com
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
syzbot is hitting might_sleep() warning at hci_sock_dev_event() due to
calling lock_sock() with rw spinlock held [1].
It seems that history of this locking problem is a trial and error.
Commit b40df5743e ("[PATCH] bluetooth: fix socket locking in
hci_sock_dev_event()") in 2.6.21-rc4 changed bh_lock_sock() to
lock_sock() as an attempt to fix lockdep warning.
Then, commit 4ce61d1c7a ("[BLUETOOTH]: Fix locking in
hci_sock_dev_event().") in 2.6.22-rc2 changed lock_sock() to
local_bh_disable() + bh_lock_sock_nested() as an attempt to fix the
sleep in atomic context warning.
Then, commit 4b5dd696f8 ("Bluetooth: Remove local_bh_disable() from
hci_sock.c") in 3.3-rc1 removed local_bh_disable().
Then, commit e305509e67 ("Bluetooth: use correct lock to prevent UAF
of hdev object") in 5.13-rc5 again changed bh_lock_sock_nested() to
lock_sock() as an attempt to fix CVE-2021-3573.
This difficulty comes from current implementation that
hci_sock_dev_event(HCI_DEV_UNREG) is responsible for dropping all
references from sockets because hci_unregister_dev() immediately
reclaims resources as soon as returning from
hci_sock_dev_event(HCI_DEV_UNREG).
But the history suggests that hci_sock_dev_event(HCI_DEV_UNREG) was not
doing what it should do.
Therefore, instead of trying to detach sockets from device, let's accept
not detaching sockets from device at hci_sock_dev_event(HCI_DEV_UNREG),
by moving actual cleanup of resources from hci_unregister_dev() to
hci_cleanup_dev() which is called by bt_host_release() when all
references to this unregistered device (which is a kobject) are gone.
Since hci_sock_dev_event(HCI_DEV_UNREG) no longer resets
hci_pi(sk)->hdev, we need to check whether this device was unregistered
and return an error based on HCI_UNREGISTER flag. There might be subtle
behavioral difference in "monitor the hdev" functionality; please report
if you found something went wrong due to this patch.
Link: https://syzkaller.appspot.com/bug?extid=a5df189917e79d5e59c9 [1]
Reported-by: syzbot <syzbot+a5df189917e79d5e59c9@syzkaller.appspotmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: e305509e67 ("Bluetooth: use correct lock to prevent UAF of hdev object")
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support hdev to allocate extra size for private data.
The size of private data is specified in the hdev_alloc_size(priv_size)
and the allocated buffer can be accessed with hci_get_priv(hdev).
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
An earlier commit replaced using batostr to using %pMR sprintf for the
construction of session->name. Static analysis detected that this new
method can use a total of 21 characters (including the trailing '\0')
so we need to increase the BTNAMSIZ from 18 to 21 to fix potential
buffer overflows.
Addresses-Coverity: ("Out-of-bounds write")
Fixes: fcb73338ed ("Bluetooth: Use %pMR in sprintf/seq_printf instead of batostr")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Code was checking if random_addr and hdev->rpa match without first
checking if the RPA has not been set (BDADDR_ANY), furthermore it was
clearing HCI_RPA_EXPIRED before the command completes and the RPA is
actually programmed which in case of failure would leave the expired
RPA still set.
Since advertising instance have a similar problem the clearing of
HCI_RPA_EXPIRED has been moved to hci_event.c after checking the random
address is in fact the hdev->rap and then proceed to set the expire
timeout.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds a field to track if advertising instances are enabled or not
and only clear HCI_LE_ADV flag if there is no instance left advertising.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Syzbot reported a corrupted list in kobject_add_internal [1]. This
happens when multiple HCI_EV_SYNC_CONN_COMPLETE event packets with
status 0 are sent for the same HCI connection. This causes us to
register the device more than once which corrupts the kset list.
As this is forbidden behavior, we add a check for whether we're
trying to process the same HCI_EV_SYNC_CONN_COMPLETE event multiple
times for one connection. If that's the case, the event is invalid, so
we report an error that the device is misbehaving, and ignore the
packet.
Link: https://syzkaller.appspot.com/bug?extid=66264bf2fd0476be7e6c [1]
Reported-by: syzbot+66264bf2fd0476be7e6c@syzkaller.appspotmail.com
Tested-by: syzbot+66264bf2fd0476be7e6c@syzkaller.appspotmail.com
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes the MGMT add_advertising command repsones with the
wrong opcode when it is trying to return the not supported error.
Fixes: cbbdfa6f33 ("Bluetooth: Enable controller RPA resolution using Experimental feature")
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
syzbot is hitting might_sleep() warning at hci_sock_dev_event()
due to calling lock_sock() with rw spinlock held [1].
It seems that history of this locking problem is a trial and error.
Commit b40df5743e ("[PATCH] bluetooth: fix socket locking in
hci_sock_dev_event()") in 2.6.21-rc4 changed bh_lock_sock() to lock_sock()
as an attempt to fix lockdep warning.
Then, commit 4ce61d1c7a ("[BLUETOOTH]: Fix locking in
hci_sock_dev_event().") in 2.6.22-rc2 changed lock_sock() to
local_bh_disable() + bh_lock_sock_nested() as an attempt to fix
sleep in atomic context warning.
Then, commit 4b5dd696f8 ("Bluetooth: Remove local_bh_disable() from
hci_sock.c") in 3.3-rc1 removed local_bh_disable().
Then, commit e305509e67 ("Bluetooth: use correct lock to prevent UAF
of hdev object") in 5.13-rc5 again changed bh_lock_sock_nested() to
lock_sock() as an attempt to fix CVE-2021-3573.
This difficulty comes from current implementation that
hci_sock_dev_event(HCI_DEV_UNREG) is responsible for dropping all
references from sockets because hci_unregister_dev() immediately reclaims
resources as soon as returning from hci_sock_dev_event(HCI_DEV_UNREG).
But the history suggests that hci_sock_dev_event(HCI_DEV_UNREG) was not
doing what it should do.
Therefore, instead of trying to detach sockets from device, let's accept
not detaching sockets from device at hci_sock_dev_event(HCI_DEV_UNREG),
by moving actual cleanup of resources from hci_unregister_dev() to
hci_release_dev() which is called by bt_host_release when all references
to this unregistered device (which is a kobject) are gone.
Link: https://syzkaller.appspot.com/bug?extid=a5df189917e79d5e59c9 [1]
Reported-by: syzbot <syzbot+a5df189917e79d5e59c9@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: syzbot <syzbot+a5df189917e79d5e59c9@syzkaller.appspotmail.com>
Fixes: e305509e67 ("Bluetooth: use correct lock to prevent UAF of hdev object")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
put_tty_driver() is an alias for tty_driver_kref_put(). There is no need
for two exported identical functions, therefore switch all users of
old put_tty_driver() to new tty_driver_kref_put() and remove the former
for good.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Acked-by: Alex Elder <elder@linaro.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
alloc_tty_driver was deprecated by tty_alloc_driver in commit
7f0bc6a68e (TTY: pass flags to alloc_tty_driver) in 2012.
I never got into eliminating alloc_tty_driver until now. So we still
have two functions for allocating drivers which might be confusing. So
get rid of alloc_tty_driver uses to eliminate it for good in the next
patch.
Note we need to switch return value checking as tty_alloc_driver uses
ERR_PTR. And flags are now a parameter of tty_alloc_driver.
Cc: Richard Henderson <rth@twiddle.net>(odd fixer:ALPHA PORT)
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch complains that some of these struct members are not initialized
leading to a stack information disclosure:
net/bluetooth/sco.c:778 sco_conn_defer_accept() warn:
check that 'cp.retrans_effort' doesn't leak information
This seems like a valid warning. I've added a default case to fix
this issue.
Fixes: 2f69a82acf ("Bluetooth: Use voice setting in deferred SCO connection request")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups. Highlights
are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM4qQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylKvQCfbh+OmTkDlDlDhSWlxuV05M1XTXoAoLUcLZru
s5JCnwSZztQQLMDHj7Pd
=Zupm
-----END PGP SIGNATURE-----
Merge tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups.
Highlights are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (227 commits)
serial: mvebu-uart: remove unused member nb from struct mvebu_uart
arm64: dts: marvell: armada-37xx: Fix reg for standard variant of UART
dt-bindings: mvebu-uart: fix documentation
serial: mvebu-uart: correctly calculate minimal possible baudrate
serial: mvebu-uart: do not allow changing baudrate when uartclk is not available
serial: mvebu-uart: fix calculation of clock divisor
tty: make linux/tty_flip.h self-contained
serial: Prefer unsigned int to bare use of unsigned
serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs
serial: qcom_geni_serial: use DT aliases according to DT bindings
Revert "tty: serial: Add UART driver for Cortina-Access platform"
tty: serial: Add UART driver for Cortina-Access platform
MAINTAINERS: add me back as mxser maintainer
mxser: Documentation, fix typos
mxser: Documentation, make the docs up-to-date
mxser: Documentation, remove traces of callout device
mxser: introduce mxser_16550A_or_MUST helper
mxser: rename flags to old_speed in mxser_set_serial_info
mxser: use port variable in mxser_set_serial_info
mxser: access info->MCR under info->slock
...
Error status of this event means that it has ended due reasons other
than a connection:
'If advertising has terminated as a result of the advertising duration
elapsing, the Status parameter shall be set to the error code
Advertising Timeout (0x3C).'
'If advertising has terminated because the
Max_Extended_Advertising_Events was reached, the Status parameter
shall be set to the error code Limit Reached (0x43).'
Fixes: acf0aeae43 ("Bluetooth: Handle ADv set terminated event")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Increment the mgmt revision due to recent changes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
These command do have variable length and the length can go up to 251,
so this changes the struct to not use a fixed size and then when
creating the PDU only the actual length of the data send to the
controller.
Fixes: a0fb3726ba ("Bluetooth: Use Set ext adv/scan rsp data if controller supports")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
blacklist -> reject list
whitelist -> accept list
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
master -> central
slave -> peripheral
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
master -> initiator (for smp) or central (everything else)
slave -> responder (for smp) or peripheral (everything else)
The #define preprocessor terms are unchanged for now to not disturb
dependent APIs.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to Documentation/core-api/printk-formats.rst,
Use the correct print format. Printing an unsigned int value should use %u
instead of %d. Otherwise printk() might end up displaying negative numbers.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to Documentation/core-api/printk-formats.rst,
Use the correct print format. Printing an unsigned int value should use %u
instead of %d. Otherwise printk() might end up displaying negative numbers.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to Documentation/core-api/printk-formats.rst,
Use the correct print format. Printing an unsigned int value should use %u
instead of %d. Otherwise printk() might end up displaying negative numbers.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to Documentation/core-api/printk-formats.rst,
Use the correct print format. Printing an unsigned int value should use %u
instead of %d. Otherwise printk() might end up displaying negative numbers.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to Documentation/core-api/printk-formats.rst,
Use the correct print format. Printing an unsigned int value should use %u
instead of %d. Otherwise printk() might end up displaying negative numbers.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to Documentation/core-api/printk-formats.rst,
Use the correct print format. Printing an unsigned int value should use %u
instead of %d. Otherwise printk() might end up displaying negative numbers.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to Documentation/core-api/printk-formats.rst,
Use the correct print format. Printing an unsigned int value should use %u
instead of %d. Otherwise printk() might end up displaying negative numbers.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to Documentation/core-api/printk-formats.rst,
Use the correct print format. Printing an unsigned int value should use %u
instead of %d. Otherwise printk() might end up displaying negative numbers.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to Documentation/core-api/printk-formats.rst,
Use the correct print format. Printing an unsigned int value should use %u
instead of %d. Otherwise printk() might end up displaying negative numbers.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to Documentation/core-api/printk-formats.rst,
Use the correct print format. Printing an unsigned int value should use %u
instead of %d. Otherwise printk() might end up displaying negative numbers.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
slave -> peripheral
blacklisted -> blocked
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
master -> initiator
slave -> responder
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced:
master -> central
slave -> peripheral
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch replaces some non-inclusive terms based on the appropriate
language mapping table compiled by the Bluetooth SIG:
https://specificationrefs.bluetooth.com/language-mapping/Appropriate_Language_Mapping_Table.pdf
Specifically, these terms are replaced when describing the
connectionless peripheral broadcast feature:
master -> central
slave -> peripheral
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This fixes parsing of LTV entries when the length is 0.
Found with:
tools/mgmt-tester -s "Add Advertising - Success (ScRsp only)"
Add Advertising - Success (ScRsp only) - run
Sending Add Advertising (0x003e)
Test condition added, total 1
[ 11.004577] ==================================================================
[ 11.005292] BUG: KASAN: slab-out-of-bounds in tlv_data_is_valid+0x87/0xe0
[ 11.005984] Read of size 1 at addr ffff888002c695b0 by task mgmt-tester/87
[ 11.006711]
[ 11.007176]
[ 11.007429] Allocated by task 87:
[ 11.008151]
[ 11.008438] The buggy address belongs to the object at ffff888002c69580
[ 11.008438] which belongs to the cache kmalloc-64 of size 64
[ 11.010526] The buggy address is located 48 bytes inside of
[ 11.010526] 64-byte region [ffff888002c69580, ffff888002c695c0)
[ 11.012423] The buggy address belongs to the page:
[ 11.013291]
[ 11.013544] Memory state around the buggy address:
[ 11.014359] ffff888002c69480: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[ 11.015453] ffff888002c69500: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[ 11.016232] >ffff888002c69580: 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc
[ 11.017010] ^
[ 11.017547] ffff888002c69600: 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc
[ 11.018296] ffff888002c69680: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
[ 11.019116] ==================================================================
Fixes: 2bb36870e8 ("Bluetooth: Unify advertising instance flags check")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the Get Device Flags command fails, it returns the error status
with the parameters filled with the garbage values. Although the
parameters are not used, it is better to fill with zero than the random
values.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Disable duplicates filter when scanning for advertisement monitor for
the following reasons. The scanning includes active scan and passive
scan.
For HW pattern filtering (ex. MSFT), Realtek and Qualcomm controllers
ignore RSSI_Sampling_Period when the duplicates filter is enabled.
For SW pattern filtering, when we're not doing interleaved scanning, it
is necessary to disable duplicates filter, otherwise hosts can only
receive one advertisement and it's impossible to know if a peer is still
in range.
Signed-off-by: Yun-Hao Chung <howardchung@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When using controller based address resolution, then the destination
address type during le_conn_complete uses 0x02 & 0x03 if controller
resolves the destination address(RPA).
These address types need to be converted back into either 0x00 0r 0x01
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use DEVICE_ATTR_RO helper instead of plain DEVICE_ATTR,
which makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The use of l2cap_chan_del is not safe under a loop using
list_for_each_entry.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The use of l2cap_chan_del is not safe under a loop using
list_for_each_entry.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Even with rate limited reporting this is very spammy and since
it is remote device that is providing bogus data there is no
need to report this as error.
Since real_len variable was used only to allow conditional error
message it is now also removed.
[72454.143336] bt_err_ratelimited: 10 callbacks suppressed
[72454.143337] Bluetooth: hci0: advertising data len corrected
[72454.296314] Bluetooth: hci0: advertising data len corrected
[72454.892329] Bluetooth: hci0: advertising data len corrected
[72455.051319] Bluetooth: hci0: advertising data len corrected
[72455.357326] Bluetooth: hci0: advertising data len corrected
[72455.663295] Bluetooth: hci0: advertising data len corrected
[72455.787278] Bluetooth: hci0: advertising data len corrected
[72455.942278] Bluetooth: hci0: advertising data len corrected
[72456.094276] Bluetooth: hci0: advertising data len corrected
[72456.249137] Bluetooth: hci0: advertising data len corrected
[72459.416333] bt_err_ratelimited: 13 callbacks suppressed
[72459.416334] Bluetooth: hci0: advertising data len corrected
[72459.721334] Bluetooth: hci0: advertising data len corrected
[72460.011317] Bluetooth: hci0: advertising data len corrected
[72460.327171] Bluetooth: hci0: advertising data len corrected
[72460.638294] Bluetooth: hci0: advertising data len corrected
[72460.946350] Bluetooth: hci0: advertising data len corrected
[72461.225320] Bluetooth: hci0: advertising data len corrected
[72461.690322] Bluetooth: hci0: advertising data len corrected
[72462.118318] Bluetooth: hci0: advertising data len corrected
[72462.427319] Bluetooth: hci0: advertising data len corrected
[72464.546319] bt_err_ratelimited: 7 callbacks suppressed
[72464.546319] Bluetooth: hci0: advertising data len corrected
[72464.857318] Bluetooth: hci0: advertising data len corrected
[72465.163332] Bluetooth: hci0: advertising data len corrected
[72465.278331] Bluetooth: hci0: advertising data len corrected
[72465.432323] Bluetooth: hci0: advertising data len corrected
[72465.891334] Bluetooth: hci0: advertising data len corrected
[72466.045334] Bluetooth: hci0: advertising data len corrected
[72466.197321] Bluetooth: hci0: advertising data len corrected
[72466.340318] Bluetooth: hci0: advertising data len corrected
[72466.498335] Bluetooth: hci0: advertising data len corrected
[72469.803299] bt_err_ratelimited: 10 callbacks suppressed
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=203753
Cc: stable@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During command status or command complete event, the controller may set
ncmd=0 indicating that it is not accepting any more commands. In such a
case, host holds off sending any more commands to the controller. If the
controller doesn't recover from such condition, host will wait forever,
until the user decides that the Bluetooth is broken and may power cycles
the Bluetooth.
This patch triggers the hardware error to reset the controller and
driver when it gets into such state as there is no other wat out.
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
0x2B, 0x31 and 0x33 are reserved for future use but were not present in
the HCI to MGMT conversion table, this caused the conversion to be
incorrect for the HCI status code greater than 0x2A.
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Yu Liu <yudiliu@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When cmtp_attach_device fails, cmtp_add_connection returns the error value
which leads to the caller to doing fput through sockfd_put. But
cmtp_session kthread, which is stopped in this path will also call fput,
leading to a potential refcount underflow or a use-after-free.
Add a refcount before we signal the kthread to stop. The kthread will try
to grab the cmtp_session_sem mutex before doing the fput, which is held
when get_file is called, so there should be no races there.
Reported-by: Ryota Shiga
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When an MGMT_EV_DEVICE_CONNECTED event is reported back to the user
space we will set the flags to tell if the established connection is
outbound or not. This is useful for the user space to log better metrics
and error messages.
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Yu Liu <yudiliu@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix the following coccicheck warning:
net/bluetooth/msft.c:37:6-13: WARNING use flexible-array member instead
net/bluetooth/msft.c:42:6-10: WARNING use flexible-array member instead
net/bluetooth/msft.c:52:6-10: WARNING use flexible-array member instead
Signed-off-by: Qiheng Lin <linqiheng@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When receiving a new connection pchan->conn won't be initialized so the
code cannot use bt_dev_dbg as the pointer to hci_dev won't be
accessible.
Fixes: 2e1614f7d6 ("Bluetooth: SMP: Convert BT_ERR/BT_DBG to bt_dev_err/bt_dev_dbg")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into tty-next
We want the tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hci_sock_dev_event() function will cleanup the hdev object for
sockets even if this object may still be in used within the
hci_sock_bound_ioctl() function, result in UAF vulnerability.
This patch replace the BH context lock to serialize these affairs
and prevent the race condition.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In the cleanup routine for failed initialization of HCI device,
the flush_work(&hdev->rx_work) need to be finished before the
flush_work(&hdev->cmd_work). Otherwise, the hci_rx_work() can
possibly invoke new cmd_work and cause a bug, like double free,
in late processings.
This was assigned CVE-2021-3564.
This patch reorder the flush_work() to fix this bug.
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-bluetooth@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: Hao Xiong <mart1n@zju.edu.cn>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
tty_operations::chars_in_buffer is another hook which is expected to
return values >= 0. So make it explicit by the return type too -- use
unsigned int.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Acked-by: David Sterba <dsterba@suse.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-27-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Line disciplines expect a positive value or zero returned from
tty->ops->write_room (invoked by tty_write_room). So make this
assumption explicit by using unsigned int as a return value. Both of
tty->ops->write_room and tty_write_room.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Alex Elder <elder@linaro.org>
Acked-by: Max Filippov <jcmvbkbc@gmail.com> # xtensa
Acked-by: David Sterba <dsterba@suse.com>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Chris Zankel <chris@zankel.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20210505091928.22010-23-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to
walk all map elements in a more robust and easier to verify
fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF
on s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices
which don't need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability
on next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is
slow in reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take
place correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP
packets before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used
to define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
-independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and
bnxt support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP
which define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay
for packets sampled from switch HW (and corresponding egress
and policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP
forwarding, bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface
to distribute MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x -
11-port Ethernet switch with 8x 1-Gigabit Ethernet
and 3x 10-Gigabit interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365
and BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack,
matching on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode
changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=vcbA
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
It seems like Fedora 34 ends up enabling a few new gcc warnings, notably
"-Wstringop-overread" and "-Warray-parameter".
Both of them cause what seem to be valid warnings in the kernel, where
we have array size mismatches in function arguments (that are no longer
just silently converted to a pointer to element, but actually checked).
This fixes most of the trivial ones, by making the function declaration
match the function definition, and in the case of intel_pm.c, removing
the over-specified array size from the argument declaration.
At least one 'stringop-overread' warning remains in the i915 driver, but
that one doesn't have the same obvious trivial fix, and may or may not
actually be indicative of a bug.
[ It was a mistake to upgrade one of my machines to Fedora 34 while
being busy with the merge window, but if this is the extent of the
compiler upgrade problems, things are better than usual - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the big set of various smaller driver subsystem updates for
5.13-rc1.
Major bits in here are:
- habanalabs driver updates
- hwtracing driver updates
- interconnect driver updates
- mhi driver updates
- extcon driver updates
- fpga driver updates
- new binder features added
- nvmem driver updates
- phy driver updates
- soundwire driver updates
- smaller misc and char driver fixes and updates.
- bluetooth driver bugfix that maintainer wanted to go through
this tree.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYIa0CQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylQ/QCgwLQleU5hH/iQwxbHgNL5GawNUroAmwZtxILF
1r6zjmGi0Ak4oFBf7A0T
=Rrl6
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of various smaller driver subsystem updates for
5.13-rc1.
Major bits in here are:
- habanalabs driver updates
- hwtracing driver updates
- interconnect driver updates
- mhi driver updates
- extcon driver updates
- fpga driver updates
- new binder features added
- nvmem driver updates
- phy driver updates
- soundwire driver updates
- smaller misc and char driver fixes and updates.
- bluetooth driver bugfix that maintainer wanted to go through this
tree.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (330 commits)
bluetooth: eliminate the potential race condition when removing the HCI controller
coresight: etm-perf: Fix define build issue when built as module
phy: Revert "phy: ti: j721e-wiz: add missing of_node_put"
phy: ti: j721e-wiz: Add missing include linux/slab.h
phy: phy-twl4030-usb: Fix possible use-after-free in twl4030_usb_remove()
stm class: Use correct UUID APIs
intel_th: pci: Add Alder Lake-M support
intel_th: pci: Add Rocket Lake CPU support
intel_th: Consistency and off-by-one fix
intel_th: Constify attribute_group structs
intel_th: Constify all drvdata references
stm class: Remove an unused function
habanalabs/gaudi: Fix uninitialized return code rc when read size is zero
greybus: es2: fix kernel-doc warnings
mei: me: add Alder Lake P device id.
dw-xdata-pcie: Update outdated info and improve text format
dw-xdata-pcie: Fix documentation build warns
fbdev: zero-fill colormap in fbcmap.c
firmware: qcom-scm: Fix QCOM_SCM configuration
speakup: i18n: Switch to kmemdup_nul() in spk_msg_set()
...
There is a possible race condition vulnerability between issuing a HCI
command and removing the cont. Specifically, functions hci_req_sync()
and hci_dev_do_close() can race each other like below:
thread-A in hci_req_sync() | thread-B in hci_dev_do_close()
| hci_req_sync_lock(hdev);
test_bit(HCI_UP, &hdev->flags); |
... | test_and_clear_bit(HCI_UP, &hdev->flags)
hci_req_sync_lock(hdev); |
|
In this commit we alter the sequence in function hci_req_sync(). Hence,
the thread-A cannot issue th.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Cc: Marcel Holtmann <marcel@holtmann.org>
Fixes: 7c6a329e44 ("[Bluetooth] Fix regression from using default link policy")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some controllers don't support the Simple Pairing Options feature that
can indicate the support for P-192 and P-256 public key validation.
However they might support the Microsoft vendor extension that can
indicate the validiation capability as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The le_scan_{int,window}_adv_monitor settings have not been set with a
sensible default.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When drivers indicate support for AOSP vendor extension, initialize them
and read its capabilities.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
own_address_type has to changed to 0x02 and 0x03 only when
HCI_ENABLE_LL_PRIVACY flag is set.
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We set hdev->cur_adv_instance in the adv param MGMT request to allow the
callback to the hci param request to set the tx power to the correct
instance. Now that the callbacks use the advertising handle from the hci
request (as they should), this workaround is no longer necessary.
Furthermore, this change resolves a race condition that is more
prevalent when using the extended advertising MGMT calls - if
hdev->cur_adv_instance is set in the params request, then when the data
request is called, we believe our new instance is already active. This
treats it as an update and immediately schedules the instance with the
controller, which has a potential race with the software rotation adv
update. By not setting hdev->cur_adv_instance too early, the new
instance is queued as it should be, to be used when the rotation comes
around again.
This change is tested on harrison peak to confirm that it resolves the
race condition on registration, and that there is no regression in
single- and multi-advertising automated tests.
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some extended advertising hci command complete events are still using
hdev->cur_adv_instance to map the request to the correct advertisement
handle. However, with extended advertising, "current instance" doesn't
make sense as we can have multiple concurrent advertisements. This
change switches these command complete handlers to use the advertising
handle from the request/event, to ensure we will always use the correct
advertising handle regardless of the state of hdev->cur_adv_instance.
This change is tested on hatch and kefka chromebooks and run through
single- and multi-advertising automated tests to confirm callbacks
report tx power to the correct advertising handle, etc.
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use the correct print format. Printing an unsigned int value should use %u
instead of %d. For details, please read document:
Documentation/core-api/printk-formats.rst
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This fixes kbuild findings:
smatch warnings:
net/bluetooth/smp.c:1633 smp_user_confirm_reply() warn: variable
dereferenced before check 'conn' (see line 1631)
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is a possibility where HCI_INQUIRY flag is set but we still
send HCI_OP_INQUIRY anyway.
Such a case can be reproduced by connecting to an LE device while
active scanning. When the device is discovered, we initiate a
connection, stop LE Scan, and send Discovery MGMT with status
disabled, but we don't cancel the inquiry.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
1. Add space when needed;
2. Block comments style fix;
3. Move open brace '{' following function definitions to the next line;
4. Remove unnecessary braces '{}' for single statement blocks.
Signed-off-by: Meng Yu <yumeng18@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
void function return statements are not generally useful.
Signed-off-by: Meng Yu <yumeng18@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Increment the mgmt revision due to recent changes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The list of trusted events should contain the advertisement monitor
events and not the untrusted one, so move entries to the correct list.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The list of supported mgmt commands for PHY configuration is missing, so
just add them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The read advertising features error handling returns false the opcode
for the set advertising command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The return error when trying to change the setting when a controller is
powered up, shall be MGMT_STATUS_REJECTED. However instead now the error
MGMT_STATUS_NOT_POWERED is used which is exactly the opposite.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
There is a possibility of receiving a zapped sock on
l2cap_sock_connect(). This could lead to interesting crashes, one
such case is tearing down an already tore l2cap_sock as is happened
with this call trace:
__dump_stack lib/dump_stack.c:15 [inline]
dump_stack+0xc4/0x118 lib/dump_stack.c:56
register_lock_class kernel/locking/lockdep.c:792 [inline]
register_lock_class+0x239/0x6f6 kernel/locking/lockdep.c:742
__lock_acquire+0x209/0x1e27 kernel/locking/lockdep.c:3105
lock_acquire+0x29c/0x2fb kernel/locking/lockdep.c:3599
__raw_spin_lock_bh include/linux/spinlock_api_smp.h:137 [inline]
_raw_spin_lock_bh+0x38/0x47 kernel/locking/spinlock.c:175
spin_lock_bh include/linux/spinlock.h:307 [inline]
lock_sock_nested+0x44/0xfa net/core/sock.c:2518
l2cap_sock_teardown_cb+0x88/0x2fb net/bluetooth/l2cap_sock.c:1345
l2cap_chan_del+0xa3/0x383 net/bluetooth/l2cap_core.c:598
l2cap_chan_close+0x537/0x5dd net/bluetooth/l2cap_core.c:756
l2cap_chan_timeout+0x104/0x17e net/bluetooth/l2cap_core.c:429
process_one_work+0x7e3/0xcb0 kernel/workqueue.c:2064
worker_thread+0x5a5/0x773 kernel/workqueue.c:2196
kthread+0x291/0x2a6 kernel/kthread.c:211
ret_from_fork+0x4e/0x80 arch/x86/entry/entry_64.S:604
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reported-by: syzbot+abfc0f5e668d4099af73@syzkaller.appspotmail.com
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
gcc-11 points out that the declaration does not match the definition:
net/bluetooth/ecdh_helper.c:122:55: error: argument 2 of type ‘const u8[32]’ {aka ‘const unsigned char[32]’} with mismatched bound [-Werror=array-parameter=]
122 | int set_ecdh_privkey(struct crypto_kpp *tfm, const u8 private_key[32])
| ~~~~~~~~~^~~~~~~~~~~~~~~
In file included from net/bluetooth/ecdh_helper.c:23:
net/bluetooth/ecdh_helper.h:28:56: note: previously declared as ‘const u8 *’ {aka ‘const unsigned char *’}
28 | int set_ecdh_privkey(struct crypto_kpp *tfm, const u8 *private_key);
| ~~~~~~~~~~^~~~~~~~~~~
Change the declaration to contain the size of the array, rather than
just a pointer.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
syzbot is hitting "INFO: trying to register non-static key." message [1],
for "struct l2cap_chan"->tx_q.lock spinlock is not yet initialized when
l2cap_chan_del() is called due to e.g. timeout.
Since "struct l2cap_chan"->lock mutex is initialized at l2cap_chan_create()
immediately after "struct l2cap_chan" is allocated using kzalloc(), let's
as well initialize "struct l2cap_chan"->{tx_q,srej_q}.lock spinlocks there.
[1] https://syzkaller.appspot.com/bug?extid=fadfba6a911f6bf71842
Reported-and-tested-by: syzbot <syzbot+fadfba6a911f6bf71842@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
hci_chan can be created in 2 places: hci_loglink_complete_evt() if
it is an AMP hci_chan, or l2cap_conn_add() otherwise. In theory,
Only AMP hci_chan should be removed by a call to
hci_disconn_loglink_complete_evt(). However, the controller might mess
up, call that function, and destroy an hci_chan which is not initiated
by hci_loglink_complete_evt().
This patch adds a verification that the destroyed hci_chan must have
been init'd by hci_loglink_complete_evt().
Example crash call trace:
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xe3/0x144 lib/dump_stack.c:118
print_address_description+0x67/0x22a mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report mm/kasan/report.c:412 [inline]
kasan_report+0x251/0x28f mm/kasan/report.c:396
hci_send_acl+0x3b/0x56e net/bluetooth/hci_core.c:4072
l2cap_send_cmd+0x5af/0x5c2 net/bluetooth/l2cap_core.c:877
l2cap_send_move_chan_cfm_icid+0x8e/0xb1 net/bluetooth/l2cap_core.c:4661
l2cap_move_fail net/bluetooth/l2cap_core.c:5146 [inline]
l2cap_move_channel_rsp net/bluetooth/l2cap_core.c:5185 [inline]
l2cap_bredr_sig_cmd net/bluetooth/l2cap_core.c:5464 [inline]
l2cap_sig_channel net/bluetooth/l2cap_core.c:5799 [inline]
l2cap_recv_frame+0x1d12/0x51aa net/bluetooth/l2cap_core.c:7023
l2cap_recv_acldata+0x2ea/0x693 net/bluetooth/l2cap_core.c:7596
hci_acldata_packet net/bluetooth/hci_core.c:4606 [inline]
hci_rx_work+0x2bd/0x45e net/bluetooth/hci_core.c:4796
process_one_work+0x6f8/0xb50 kernel/workqueue.c:2175
worker_thread+0x4fc/0x670 kernel/workqueue.c:2321
kthread+0x2f0/0x304 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:415
Allocated by task 38:
set_track mm/kasan/kasan.c:460 [inline]
kasan_kmalloc+0x8d/0x9a mm/kasan/kasan.c:553
kmem_cache_alloc_trace+0x102/0x129 mm/slub.c:2787
kmalloc include/linux/slab.h:515 [inline]
kzalloc include/linux/slab.h:709 [inline]
hci_chan_create+0x86/0x26d net/bluetooth/hci_conn.c:1674
l2cap_conn_add.part.0+0x1c/0x814 net/bluetooth/l2cap_core.c:7062
l2cap_conn_add net/bluetooth/l2cap_core.c:7059 [inline]
l2cap_connect_cfm+0x134/0x852 net/bluetooth/l2cap_core.c:7381
hci_connect_cfm+0x9d/0x122 include/net/bluetooth/hci_core.h:1404
hci_remote_ext_features_evt net/bluetooth/hci_event.c:4161 [inline]
hci_event_packet+0x463f/0x72fa net/bluetooth/hci_event.c:5981
hci_rx_work+0x197/0x45e net/bluetooth/hci_core.c:4791
process_one_work+0x6f8/0xb50 kernel/workqueue.c:2175
worker_thread+0x4fc/0x670 kernel/workqueue.c:2321
kthread+0x2f0/0x304 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:415
Freed by task 1732:
set_track mm/kasan/kasan.c:460 [inline]
__kasan_slab_free mm/kasan/kasan.c:521 [inline]
__kasan_slab_free+0x106/0x128 mm/kasan/kasan.c:493
slab_free_hook mm/slub.c:1409 [inline]
slab_free_freelist_hook+0xaa/0xf6 mm/slub.c:1436
slab_free mm/slub.c:3009 [inline]
kfree+0x182/0x21e mm/slub.c:3972
hci_disconn_loglink_complete_evt net/bluetooth/hci_event.c:4891 [inline]
hci_event_packet+0x6a1c/0x72fa net/bluetooth/hci_event.c:6050
hci_rx_work+0x197/0x45e net/bluetooth/hci_core.c:4791
process_one_work+0x6f8/0xb50 kernel/workqueue.c:2175
worker_thread+0x4fc/0x670 kernel/workqueue.c:2321
kthread+0x2f0/0x304 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:415
The buggy address belongs to the object at ffff8881d7af9180
which belongs to the cache kmalloc-128 of size 128
The buggy address is located 24 bytes inside of
128-byte region [ffff8881d7af9180, ffff8881d7af9200)
The buggy address belongs to the page:
page:ffffea00075ebe40 count:1 mapcount:0 mapping:ffff8881da403200 index:0x0
flags: 0x8000000000000200(slab)
raw: 8000000000000200 dead000000000100 dead000000000200 ffff8881da403200
raw: 0000000000000000 0000000080150015 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8881d7af9080: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
ffff8881d7af9100: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
>ffff8881d7af9180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8881d7af9200: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8881d7af9280: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reported-by: syzbot+98228e7407314d2d4ba2@syzkaller.appspotmail.com
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently l2cap_chan_set_defaults() reset chan->conf_state to zero.
However, there is a flag CONF_NOT_COMPLETE which is set when
creating the l2cap_chan. It is suggested that the flag should be
cleared when l2cap_chan is ready, but when l2cap_chan_set_defaults()
is called, l2cap_chan is not yet ready. Therefore, we must set this
flag as the default.
Example crash call trace:
__dump_stack lib/dump_stack.c:15 [inline]
dump_stack+0xc4/0x118 lib/dump_stack.c:56
panic+0x1c6/0x38b kernel/panic.c:117
__warn+0x170/0x1b9 kernel/panic.c:471
warn_slowpath_fmt+0xc7/0xf8 kernel/panic.c:494
debug_print_object+0x175/0x193 lib/debugobjects.c:260
debug_object_assert_init+0x171/0x1bf lib/debugobjects.c:614
debug_timer_assert_init kernel/time/timer.c:629 [inline]
debug_assert_init kernel/time/timer.c:677 [inline]
del_timer+0x7c/0x179 kernel/time/timer.c:1034
try_to_grab_pending+0x81/0x2e5 kernel/workqueue.c:1230
cancel_delayed_work+0x7c/0x1c4 kernel/workqueue.c:2929
l2cap_clear_timer+0x1e/0x41 include/net/bluetooth/l2cap.h:834
l2cap_chan_del+0x2d8/0x37e net/bluetooth/l2cap_core.c:640
l2cap_chan_close+0x532/0x5d8 net/bluetooth/l2cap_core.c:756
l2cap_sock_shutdown+0x806/0x969 net/bluetooth/l2cap_sock.c:1174
l2cap_sock_release+0x64/0x14d net/bluetooth/l2cap_sock.c:1217
__sock_release+0xda/0x217 net/socket.c:580
sock_close+0x1b/0x1f net/socket.c:1039
__fput+0x322/0x55c fs/file_table.c:208
____fput+0x17/0x19 fs/file_table.c:244
task_work_run+0x19b/0x1d3 kernel/task_work.c:115
exit_task_work include/linux/task_work.h:21 [inline]
do_exit+0xe4c/0x204a kernel/exit.c:766
do_group_exit+0x291/0x291 kernel/exit.c:891
get_signal+0x749/0x1093 kernel/signal.c:2396
do_signal+0xa5/0xcdb arch/x86/kernel/signal.c:737
exit_to_usermode_loop arch/x86/entry/common.c:243 [inline]
prepare_exit_to_usermode+0xed/0x235 arch/x86/entry/common.c:277
syscall_return_slowpath+0x3a7/0x3b3 arch/x86/entry/common.c:348
int_ret_from_sys_call+0x25/0xa3
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reported-by: syzbot+338f014a98367a08a114@syzkaller.appspotmail.com
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Skip updation of tx and rx PHYs values, when PHY Update
event's status is not successful.
Signed-off-by: Ayush Garg <ayush.garg@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This converts instances of BT_ERR and BT_DBG to bt_dev_err and
bt_dev_dbg which can be enabled at runtime when BT_FEATURE_DEBUG is
enabled.
Note: Not all instances could be converted as some are exercised by
selftest.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When receiving L2CAP_CREDIT_BASED_CONNECTION_REQ the remote may request
more channels than allowed by the spec (10 octecs = 5 CIDs) so this
checks if the number of channels is bigger than the maximum allowed and
respond with an error.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Not cancelling it has caused a bug where passive background scanning is
disabled out of the blue, preventing BLE keyboards/mice to reconnect.
Here is how it happens:
After hci_req_stop_discovery, there is still le_scan_restart_work
scheduled. Invocation of le_scan_restart_work causes a harmful
le_scan_disable_work to be scheduled. This le_scan_disable_work will
eventually disable passive scanning when the timer fires.
Sample btmon trace:
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7
Type: Passive (0x00)
Interval: 367.500 msec (0x024c)
Window: 37.500 msec (0x003c)
Own address type: Public (0x00)
Filter policy: Accept all advertisement (0x00)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Scan Parameters (0x08|0x000b) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2
Scanning: Enabled (0x01)
Filter duplicates: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Scan Enable (0x08|0x000c) ncmd 2
Status: Success (0x00)
...
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2
Scanning: Disabled (0x00)
Filter duplicates: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Scan Enable (0x08|0x000c) ncmd 2
Status: Success (0x00)
// Background scanning is not working here onwards.
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
1. crypto and crypto/atmel-ecc:
Move curve id of ECDH from the key into the algorithm name instead
in crypto and atmel-ecc, so ECDH algorithm name change form 'ecdh'
to 'ecdh-nist-pxxx', and we cannot use 'curve_id' in 'struct ecdh';
2. crypto/testmgr and net/bluetooth:
Modify 'testmgr.c', 'testmgr.h' and 'net/bluetooth' to adapt
the modification.
Signed-off-by: Meng Yu <yumeng18@huawei.com>
Reviewed-by: Zaibo Xu <xuzaibo@huawei.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This fails the pairing procedure when both remote and local non-debug
public keys are identical.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
An issue was found, where if a bluetooth client requests a broadcast
advertisement with scan response data, it will not be properly
registered with the controller. This is because at the time that the
hci_cp_le_set_scan_param structure is created, the scan response will
not yet have been received since it comes in a second MGMT call. With
empty scan response, the request defaults to a non-scannable PDU type.
On some controllers, the subsequent scan response request will fail due
to incorrect PDU type, and others will succeed and not use the scan
response.
This fix allows the advertising parameters MGMT call to include a flag
to let the kernel know whether a scan response will be coming, so that
the correct PDU type is used in the first place. A bluetoothd change is
also incoming to take advantage of it.
To test this, I created a broadcast advertisement with scan response
data and registered it on the hatch chromebook. Without this change, the
request fails, and with it will succeed.
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During suspend, there are a few scan enable and set event filter
commands that don't need to be sent unless there are actual BR/EDR
devices capable of waking the system. Check the HCI_PSCAN bit before
writing scan enable and use a new dev flag, HCI_EVENT_FILTER_CONFIGURED
to control whether to clear the event filter.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When suspending, Bluetooth disconnects all connected peers devices. If
an LE connection is started but isn't completed, we will see an LE
Create Connection Cancel instead of an HCI disconnect. This just adds
a check to see if an LE cancel was the last disconnected device and wake
the suspend thread when that is the case.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
el/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2021-02-11
Here's the main bluetooth-next pull request for 5.12:
- Add support for advertising monitor offliading using Microsoft
vendor extensions
- Add firmware download support for MediaTek MT7921U USB devices
- Suspend-related fixes for Qualcomm devices
- Add support for Intel GarfieldPeak controller
- Various other smaller fixes & cleanups
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If a peer device doesn't support eSCO 2M we should skip the params that
use it when setting up sync connection since they will always fail.
Signed-off-by: Yu Liu <yudiliu@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.
Reported-by: Abaci Robot<abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Zhong <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some devices, e.g. the RTL8723BS bluetooth part, some USB attached devices,
completely drop from the bus on a system-suspend. These devices will
have their driver unbound and rebound on resume (when the dropping of
the bus gets detected) and will show up as a new HCI after resume.
These devices do not benefit from the suspend / resume handling work done
by the hci_suspend_notifier. At best this unnecessarily adds some time to
the suspend/resume time. But this may also actually cause problems, if the
code doing the driver unbinding runs after the pm-notifier then the
hci_suspend_notifier code will try to talk to a device which is now in
an uninitialized state.
This commit adds a new HCI_QUIRK_NO_SUSPEND_NOTIFIER quirk which allows
drivers to opt-out of the hci_suspend_notifier when they know beforehand
that their device will be fully re-initialized / reprobed on resume.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These Kconfig files are included from net/Kconfig, inside the
if NET ... endif.
Remove 'depends on NET', which we know it is already met.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210125232026.106855-1-masahiroy@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bluetooth Core Specification v5.2, Vol. 3, Part A, section 1.4, table
1.1:
'Start Fragments always either begin with the first octet of the Basic
L2CAP header of a PDU or they have a length of zero (see [Vol 2] Part
B, Section 6.6.2).'
Apparently this was changed by the following errata:
https://www.bluetooth.org/tse/errata_view.cfm?errata_id=10216
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jump to the label done to decrement the reference count of HCI device
hdev on path that the Inquiry procedure is interrupted.
Fixes: 3e13fa1e1f ("Bluetooth: Fix hci_inquiry ioctl usage")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds logic to disable and reenable advertisement filters during
suspend and resume. After this patch, we would only receive packets from
devices in allow list during suspend.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When MSFT extension is supported, we don't have to interleave the scan
as we could just do allowlist scan.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implements the feature to disable/enable the filter used for
advertising monitor on MSFT controller, effectively have the same
effect as "remove all monitors" and "add all previously removed
monitors".
This feature would be needed when suspending, where we would not want
to get packets from anything outside the allowlist. Note that the
integration with the suspending part is not included in this patch.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Yun-Hao Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the controller is powered off, the registered advertising monitor
is removed from the controller. This patch handles the re-registration
of those monitors when the power is on.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Yun-Hao Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enables advertising monitor offloading to the controller, if MSFT
extension is supported. The kernel won't adjust the monitor parameters
to match what the controller supports - that is the user space's
responsibility.
This patch only manages the addition of monitors. Monitor removal is
going to be handled by another patch.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Yun-Hao Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
MSFT needs rssi parameter for monitoring advertisement packet,
therefore we should supply them from mgmt. This adds a new opcode
to add advertisement monitor with rssi parameters.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Yun-Hao Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
u128_xor() takes pointers to quantities that are assumed to be at least
64-bit aligned, which is not guaranteed to be the case in the smp_c1()
routine. So switch to crypto_xor() instead.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Looks like this was missed when patching the source to clear the structures
throughout, causing this one instance to clear the struct after the response
id is assigned.
Fixes: eddb773211 ("Bluetooth: A2MP: Fix not initializing all members")
Signed-off-by: Christopher William Snowhill <chris@kode54.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Just like MGMT_OP_START_DISCOVERY, we should reject
MGMT_OP_START_SERVICE_DISCOVERY with MGMT_STATUS_BUSY when we are paused
for suspend.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add a missing SUSPEND_SCAN_ENABLE in passive scan, remove the separate
function for configuring le scan during suspend and update the request
complete function to clear both enable and disable tasks.
Fixes: dce0a4be80 ("Bluetooth: Set missing suspend task bits")
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Increment the mgmt revision due to the recently added new commands.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When suspending, mark SUSPEND_SCAN_ENABLE and SUSPEND_SCAN_DISABLE tasks
correctly when either classic or le scanning is modified.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For advertising, we wish to know the LE tx power capabilities of the
controller in userspace, so this patch edits the Security Info MGMT
command to be more generic, such that other various controller
capabilities can be included in the EIR data. This change also includes
the LE min and max tx power into this newly-named command.
The change was tested by manually verifying that the MGMT command
returns the tx power range as expected in userspace.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Queries tx power via HCI_LE_Read_Transmit_Power command when the hci
device is initialized, and stores resulting min/max LE power in hdev
struct. If command isn't available (< BT5 support), min/max values
both default to HCI_TX_POWER_INVALID.
This patch is manually verified by ensuring BT5 devices correctly query
and receive controller tx power range.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch takes the min/max intervals and tx power optionally provided
in mgmt interface, stores them in the advertisement struct, and uses
them when configuring the hci requests. While tx power is not used if
extended advertising is unavailable, software rotation will use the min
and max advertising intervals specified by the client.
This change is validated manually by ensuring the min/max intervals are
propagated to the controller on both hatch (extended advertising) and
kukui (no extended advertising) chromebooks, and that tx power is
propagated correctly on hatch. These tests are performed with multiple
advertisements simultaneously.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds support for the new advertising add interface, with the
first command setting advertising parameters and the second to set
advertising data. The set parameters command allows the caller to leave
some fields "unset", with a params bitfield defining which params were
purposefully set. Unset parameters will be given defaults when calling
hci_add_adv_instance. The data passed to the param mgmt command is
allowed to be flexible, so in the future if bluetoothd passes a larger
structure with new params, the mgmt command will ignore the unknown
members at the end.
This change has been validated on both hatch (extended advertising) and
kukui (no extended advertising) chromebooks running bluetoothd that
support this new interface. I ran the following manual tests:
- Set several (3) advertisements using modified test_advertisement.py
- For each, validate correct data and parameters in btmon trace
- Verified both for software rotation and extended adv
Automatic test suite also run, testing many (25) scenarios of single and
multi-advertising for data/parameter correctness.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We wish to handle advertising data separately from advertising
parameters in our new MGMT requests. This change adds a helper that
allows the advertising data and scan response to be updated for an
existing advertising instance.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch add a configurable parameter to switch off the interleave
scan feature.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Refactor read default system configuration function so that it's capable
of returning different types than u16
Signed-off-by: Howard Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds code to handle the active scan during interleave
scan. The interleave scan will be canceled when users start active scan,
and it will be restarted after active scan stopped.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds code to handle the system suspension during interleave
scan. The interleave scan will be canceled when the system is going to
sleep, and will be restarted after waking up.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch implements the interleaving between allowlist scan and
no-filter scan. It'll be used to save power when at least one monitor is
registered and at least one pending connection or one device to be
scanned for.
The durations of the allowlist scan and the no-filter scan are
controlled by MGMT command: Set Default System Configuration. The
default values are set randomly for now.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
During controller initialization, an LE Set RPA Timeout command is sent
to the controller if supported. However, the value checked to determine
if the command is supported is incorrect. Page 1921 of the Bluetooth
Core Spec v5.2 shows that bit 2 of octet 35 of the Supported_Commands
field corresponds to the LE Set RPA Timeout command, but currently
bit 6 of octet 35 is checked. This patch checks the correct value
instead.
This issue led to the error seen in the following btmon output during
initialization of an adapter (rtl8761b) and prevented initialization
from completing.
< HCI Command: LE Set Resolvable Private Address Timeout (0x08|0x002e) plen 2
Timeout: 900 seconds
> HCI Event: Command Complete (0x0e) plen 4
LE Set Resolvable Private Address Timeout (0x08|0x002e) ncmd 2
Status: Unsupported Remote Feature / Unsupported LMP Feature (0x1a)
= Close Index: 00:E0:4C:6B:E5:03
The error did not appear when running with this patch.
Signed-off-by: Edward Vear <edwardvear@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This renames get_adv_instance_scan_rsp to adv_instance_is_scannable and
make it return a bool since it was not actually properly return the size
of the scan response as one could expect.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Current code is actually failing on the following tests of mgmt-tester
because get_adv_instance_scan_rsp_len did not account for flags that
cause scan response data to be included resulting in non-scannable
instance when in fact it should be scannable.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This test case is meant to verify that multiple
unknown options is included in the response.
BLUETOOTH CORE SPECIFICATION Version 5.2 | Vol 3, Part A
page 1057
'On an unknown option failure (Result=0x0003),
the option(s) that contain anoption type field that is not
understood by the recipient of the L2CAP_CONFIGURATION_REQ
packet shall be included in the L2CAP_CONFIGURATION_RSP
packet unless they are hints.'
Before this patch:
> ACL Data RX: Handle 11 flags 0x02 dlen 24
L2CAP: Configure Request (0x04) ident 18 len 16
Destination CID: 64
Flags: 0x0000
Option: Unknown (0x10) [mandatory]
10 00 11 02 11 00 12 02 12 00
< ACL Data TX: Handle 11 flags 0x00 dlen 17
L2CAP: Configure Response (0x05) ident 18 len 9
Source CID: 64
Flags: 0x0000
Result: Failure - unknown options (0x0003)
Option: Unknown (0x10) [mandatory]
12
After this patch:
> ACL Data RX: Handle 11 flags 0x02 dlen 24
L2CAP: Configure Request (0x04) ident 5 len 16
Destination CID: 64
Flags: 0x0000
Option: Unknown (0x10) [mandatory]
10 00 11 02 11 00 12 02 12 00
< ACL Data TX: Handle 11 flags 0x00 dlen 23
L2CAP: Configure Response (0x05) ident 5 len 15
Source CID: 64
Flags: 0x0000
Result: Failure - unknown options (0x0003)
Option: Unknown (0x10) [mandatory]
10 11 01 11 12 01 12
Signed-off-by: Jimmy Wahlberg <jimmywa@spotify.com>
Reviewed-by: Luiz Augusto Von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This replaces the BT_DBG function to bt_dev_dbg as it is cleaner to show
the controller index in the debug message.
Signed-off-by: Howard Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to the spec Ver 5.2, Vol 3, Part C, Sec 5.2.2.8:
Device in security mode 4 level 4 shall enforce:
128-bit equivalent strength for link and encryption keys required
using FIPS approved algorithms (E0 not allowed, SAFER+ not allowed,
and P-192 not allowed; encryption key not shortened)
This patch rejects connection with key size below 16 for FIPS
level services.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A different wait queue was used when removing ctrl_wait than when adding
it. This effectively made the remove operation without locking compared
to other operations on the wait queue ctrl_wait was part of. This caused
issues like below where dead000000000100 is LIST_POISON1 and
dead000000000200 is LIST_POISON2.
list_add corruption. next->prev should be prev (ffffffc1b0a33a08), \
but was dead000000000200. (next=ffffffc03ac77de0).
------------[ cut here ]------------
CPU: 3 PID: 2138 Comm: bluetoothd Tainted: G O 4.4.238+ #9
...
---[ end trace 0adc2158f0646eac ]---
Call trace:
[<ffffffc000443f78>] __list_add+0x38/0xb0
[<ffffffc0000f0d04>] add_wait_queue+0x4c/0x68
[<ffffffc00020eecc>] __pollwait+0xec/0x100
[<ffffffc000d1556c>] bt_sock_poll+0x74/0x200
[<ffffffc000bdb8a8>] sock_poll+0x110/0x128
[<ffffffc000210378>] do_sys_poll+0x220/0x480
[<ffffffc0002106f0>] SyS_poll+0x80/0x138
[<ffffffc00008510c>] __sys_trace_return+0x0/0x4
Unable to handle kernel paging request at virtual address dead000000000100
...
CPU: 4 PID: 5387 Comm: kworker/u15:3 Tainted: G W O 4.4.238+ #9
...
Call trace:
[<ffffffc0000f079c>] __wake_up_common+0x7c/0xa8
[<ffffffc0000f0818>] __wake_up+0x50/0x70
[<ffffffc000be11b0>] sock_def_wakeup+0x58/0x60
[<ffffffc000de5e10>] l2cap_sock_teardown_cb+0x200/0x224
[<ffffffc000d3f2ac>] l2cap_chan_del+0xa4/0x298
[<ffffffc000d45ea0>] l2cap_conn_del+0x118/0x198
[<ffffffc000d45f8c>] l2cap_disconn_cfm+0x6c/0x78
[<ffffffc000d29934>] hci_event_packet+0x564/0x2e30
[<ffffffc000d19b0c>] hci_rx_work+0x10c/0x360
[<ffffffc0000c2218>] process_one_work+0x268/0x460
[<ffffffc0000c2678>] worker_thread+0x268/0x480
[<ffffffc0000c94e0>] kthread+0x118/0x128
[<ffffffc000085070>] ret_from_fork+0x10/0x20
---[ end trace 0adc2158f0646ead ]---
Signed-off-by: Ole Bjørn Midtbø <omidtbo@cisco.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Avoid multiple attempts to create the debugfs entry, force_bredr_smp,
by moving it from the SMP registration to the BR/EDR controller init
section. hci_debugfs_create_bredr is only called when HCI_SETUP and
HCI_CONFIG is not set.
Signed-off-by: Claire Chang <tientzu@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When adding device to white list the device is added to resolving list
also. It has to be added only when HCI_ENABLE_LL_PRIVACY flag is set.
HCI_ENABLE_LL_PRIVACY flag has to be tested before adding/deleting devices
to resolving list. use_ll_privacy macro is used only to check if controller
supports LL_Privacy.
https://bugzilla.kernel.org/show_bug.cgi?id=209745
Fixes: 0eee35bdfa ("Bluetooth: Update resolving list when updating whitelist")
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When an LE connection request is made, advertising is disabled and never
resumed. When a client has an active advertisement, this is disruptive.
This change adds resume logic for client-configured (non-directed)
advertisements after the connection attempt.
The patch was tested by registering an advertisement, initiating an LE
connection from a remote peer, and verifying that the advertisement is
re-activated after the connection is established. This is performed on
Hatch and Kukui Chromebooks.
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
AMP_MGR is getting derefernced in hci_phy_link_complete_evt(), when called
from hci_event_packet() and there is a possibility, that hcon->amp_mgr may
not be found when accessing after initialization of hcon.
- net/bluetooth/hci_event.c:4945
The bug seems to get triggered in this line:
bredr_hcon = hcon->amp_mgr->l2cap_conn->hcon;
Fix it by adding a NULL check for the hcon->amp_mgr before checking the ev-status.
Fixes: d5e911928b ("Bluetooth: AMP: Process Physical Link Complete evt")
Reported-and-tested-by: syzbot+0bef568258653cff272f@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=0bef568258653cff272f
Signed-off-by: Anmol Karn <anmol.karan123@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-09-29
Here's the main bluetooth-next pull request for 5.10:
- Multiple fixes to suspend/resume handling
- Added mgmt events for controller suspend/resume state
- Improved extended advertising support
- btintel: Enhanced support for next generation controllers
- Added Qualcomm Bluetooth SoC WCN6855 support
- Several other smaller fixes & improvements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This checks if BT_HS is enabled relecting it on MGMT_SETTING_HS instead
of always reporting it as supported.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth High Speed requires hardware support which is very uncommon
nowadays since HS has not pickup interest by the industry.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Only sockets will have the chan->data set to an actual sk, channels
like A2MP would have its own data which would likely cause a crash when
calling sk_filter, in order to fix this a new callback has been
introduced so channels can implement their own filtering if necessary.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This fixes various places where a stack variable is used uninitialized.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During system powercycle when trying to get the random address
hci_get_random_address set own_addr_type as 0x01. In which if we enable
ll_privacy it is supposed to be 0x03.
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently the code auto-creates hci_conn only if the remote address has
been discovered before. This may not be the case. For example, the
remote device may trigger connection after reboot at already-paired
state so there is no inquiry result found, but it is still correct to
create the hci_conn when Connection Complete event is received.
A better guard is to check against bredr allowlist. Devices in the
allowlist have been given permission to auto-connect.
Fixes: 4f40afc6c7 ("Bluetooth: Handle BR/EDR devices during suspend")
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Set scan parameters when there is at least one Advertisement monitor.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This fixes the count of Adv monitor upon monitor removal.
The following test was performed.
- Start two btmgmt consoles, issue a btmgmt advmon-remove command on one
console and observe a MGMT_EV_ADV_MONITOR_REMOVED event on the other.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Drop repeated words in net/bluetooth/.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the controller will continue advertising when the system
enters suspend. This patch makes sure that all advertising instances are
paused when entering suspend, and resumed when suspend exits.
The Advertising and Suspend/Resume test suites were both run on this
change on 4.19 kernel with both hardware offloaded multi-advertising and
software rotated multi-advertising. In addition, a new test was added
that performs the following steps:
* Register 3 advertisements via bluez RegisterAdvertisement
* Verify reception of all advertisements by remote peer
* Enter suspend on DUT
* Verify failure to receive all advertisements by remote peer
* Exit suspend on DUT
* Verify reception of all advertisements by remote peer
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Emit controller suspend and resume events when we are ready for suspend
and we've resumed from suspend.
The controller suspend event will report whatever suspend state was
successfully entered. The controller resume event will check the first
HCI event that was received after we finished preparing for suspend and,
if it was a connection event, store the address of the peer that caused
the event. If it was not a connection event, we mark the wake reason as
an unexpected event.
Here is a sample btmon trace with these events:
@ MGMT Event: Controller Suspended (0x002d) plen 1
Suspend state: Page scanning and/or passive scanning (2)
@ MGMT Event: Controller Resumed (0x002e) plen 8
Wake reason: Remote wake due to peer device connection (2)
LE Address: CD:F3:CD:13:C5:9A (OUI CD-F3-CD)
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Luiz Augusto von Dentz