The code to prevent a bus suspend if a USB3 port was still in link training
also reacted to USB2 port polling state.
This caused bus suspend to busyloop in some cases.
USB2 polling state is different from USB3, and should not prevent bus
suspend.
Limit the USB3 link training state check to USB3 root hub ports only.
The origial commit went to stable so this need to be applied there as well
Fixes: 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactoring, no functional changes.
But worth mentioning that checking for port link resume state is now behind
a additional port power check.
This is fine as ports can't be in resume state if port power bit is not
set.
xhci spec section 4.19.1.1.6 figure 34 shows that port power bit must be
set for all 'Enable' substates, including U0,U1,U2,U3 (suspended), Resume,
and RExit states.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move U0 link state handing to USB3 and USB2 specific functions
Note that
bus_state->resuming_ports:
bus_state->resume_done[]:
are only used for USB2, and don't need to cleared for USB3 ports
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Group the code where the wPortstatus and wPortChange bits
are set into one place.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mostly refactoring, with the exception that USB_PORT_STAT_L1 link state
is reported if xhci port link is in U2 AND port is powered.
Previously we did not check if the port was powered, but according to
xhci spec 4.19.1.1.6 All the 'Enabled' states, including
USB_PORT_STAT_L1 (U2), U1, U0 and U3 must have Port power bit set.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the bus_state structure under struct usb_hub.
We need a bus_state strucure for each roothub to keep track of suspend
related info for each port.
Instead of keeping an array of two bus_state structures right under
struct xhci, it makes more sense move them to the xhci_hub structure.
No functional changes.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB3 roothub might autosuspend before a plugged USB3 device is detected,
causing USB3 device enumeration failure.
USB3 devices don't show up as connected and enabled until USB3 link trainig
completes. On a fast booting platform with a slow USB3 link training the
link might reach the connected enabled state just as the bus is suspending.
If this device is discovered first time by the xhci_bus_suspend() routine
it will be put to U3 suspended state like the other ports which failed to
suspend earlier.
The hub thread will notice the connect change and resume the bus,
moving the port back to U0
This U0 -> U3 -> U0 transition right after being connected seems to be
too much for some devices, causing them to first go to SS.Inactive state,
and finally end up stuck in a polling state with reset asserted
Fix this by failing the bus suspend if a port has a connect change or is
in a polling state in xhci_bus_suspend().
Don't do any port changes until all ports are checked, buffer all port
changes and only write them in the end if suspend can proceed
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This definition is used by msecs_to_jiffies in milliseconds.
According to the comments, max rexit timeout should be 20ms.
Align with the comments to properly calculate the delay.
Verified on Sunrise Point-LP and Cannon Lake.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek USB3.0 Card Reader [0bda:0328] reports wrong port status on
Cannon lake PCH USB3.1 xHCI [8086:a36d] after resume from S3,
after clear port reset it works fine.
Since this device is registered on USB3 roothub at boot,
when port status reports not superspeed, xhci_get_port_status will call
an uninitialized completion in bus_state[0].
Kernel will hang because of NULL pointer.
Restrict the USB2 resume status check in USB2 roothub to fix hang issue.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When USB bus host controller root hub resumes from autosuspend,
it immediately tries to enter auto-suspend, but there can be a
scenario when root hub is resuming its usb2 ports, in that particular
case USB host controller auto suspend fails since it is busy
to resuming its usb2 ports.
This makes multiple failed cycles of auto-suspend until all usb2
ports of host controller root hub do not resume.
This patch uses USB core framework usb_hcd_start_port_resume,
usb_hcd_end_port_resume API's in order to autoresume/autosuspend
root hub properly.
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the new get_resuming_ports HCD method to
the xhci-hcd driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_get_ports() is one of the last functions using port_arrays in
xhci-hub.c. We get the same data directly from hub and port structures
instead, so convert and remove both xhci_get_ports() and port_arrays from
all function that no longer need it.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use pointers to port array and port index as function parameters
in xhci_test_and_clear_bit(), just use a pointer to the right port
structure.
xhci_test_and_clear_bit() was the last port_array user in
xhci_get_port_status() and handle_port_status(), so remove the
port_array from them as well.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove old iomem port array and index as parameters, just
send a ponter to a port strucure instread
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use port structures instead of mmio port arrays for
xhci_port_missing_cas_quirk() and xhci_set_remote_wake_mask() in
xhci-hub.c
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new port structures for functions in xhci-hub.c to get
port mmio address of portsc register instead of the port array
xhci_get_port_io_addr() is no longer needeed and is removed.
Plan is to get rid of the mmio port array completely.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
quick way to get the xhci roothub and thus all the ports
belonging to a certain hcd
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hub driver will try to disable a USB3 device twice at logical disconnect,
racing with xhci_free_dev() callback from the first port disable.
This can be triggered with "udisksctl power-off --block-device <disk>"
or by writing "1" to the "remove" sysfs file for a USB3 device
in 4.17-rc4.
USB3 devices don't have a similar disabled link state as USB2 devices,
and use a U3 suspended link state instead. In this state the port
is still enabled and connected.
hub_port_connect() first disconnects the device, then later it notices
that device is still enabled (due to U3 states) it will try to disable
the port again (set to U3).
The xhci_free_dev() called during device disable is async, so checking
for existing xhci->devs[i] when setting link state to U3 the second time
was successful, even if device was being freed.
The regression was caused by, and whole thing revealed by,
Commit 44a182b9d1 ("xhci: Fix use-after-free in xhci_free_virt_device")
which sets xhci->devs[i]->udev to NULL before xhci_virt_dev() returned.
and causes a NULL pointer dereference the second time we try to set U3.
Fix this by checking xhci->devs[i]->udev exists before setting link state.
The original patch went to stable so this fix needs to be applied there as
well.
Fixes: 44a182b9d1 ("xhci: Fix use-after-free in xhci_free_virt_device")
Cc: <stable@vger.kernel.org>
Reported-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Tested-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When disabling a USB3 port the hub driver will set the port link state to
U3 to prevent "ejected" or "safely removed" devices that are still
physically connected from immediately re-enumerating.
If the device was really unplugged, then error messages were printed
as the hub tries to set the U3 link state for a port that is no longer
enabled.
xhci-hcd ee000000.usb: Cannot set link state.
usb usb8-port1: cannot disable (err = -32)
Don't print error message in xhci-hub if hub tries to set port link state
for a disabled port. Return -ENODEV instead which also silences hub driver.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For AMD Promontory xHCI host, although you can disable USB ports in
BIOS settings, those ports will be enabled anyway after you remove a
device on that port and re-plug it in again. It's a known limitation of
the chip. As a workaround we can clear the PORT_WAKE_BITS.
[commit and code comment rephrasing -Mathias]
Signed-off-by: Joe Lee <asmt.swfae@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trace the port status of each port of a roothub when
the xhci roothub receives a Get Hub Status request.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add tracing showing the port status register content each time
the xhci roothub receives a Get Port Status request.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commands with input contexts are allocated with the
xhci_alloc_command_with_ctx helper.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_stop_device() calls xhci_queue_stop_endpoint() multiple times
without checking the return value. xhci_queue_stop_endpoint() can
return error if the HC is already halted or unable to queue commands.
This can cause a deadlock condition as xhci_stop_device() would
end up waiting indefinitely for a completion for the command that
didn't get queued. Fix this by checking the return value and bailing
out of xhci_stop_device() in case of error. This patch happens to fix
potential memory leaks of the allocated command structures as well.
Fixes: c311e391a7 ("xhci: rework command timeout and cancellation,")
Cc: <stable@vger.kernel.org>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_disable_slot() allows the invoker to pass a command pointer
as paramenter. Otherwise, it will allocate one. This will cause
memory leak when a command structure was allocated inside of this
function while queuing command trb fails. Another problem comes up
when the invoker passed a command pointer, but xhci_disable_slot()
frees it when it detects a dead host.
This patch fixes these two problems by removing the command parameter
from xhci_disable_slot().
Fixes: f9e609b824 ("usb: xhci: Add helper function xhci_disable_slot().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_disable_slot() is a helper for disabling a slot when a device
goes away or recovers from error situations. Currently, it checks
the corespoding virt-dev pointer and returns directly (w/o issuing
disable slot command) if it's null.
This is unnecessary and will cause problems in case where virt-dev
allocation fails and xhci_disable_slot() is called to roll back the
hardware state. Refer to the implementation of xhci_alloc_dev().
This patch removes lines to check virt-dev in xhci_disable_slot().
Fixes: f9e609b824 ("usb: xhci: Add helper function xhci_disable_slot().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit dec08194ff.
Commit dec08194ff ("xhci: Limit USB2 port wake support for AMD Promontory
hosts") makes all high speed USB ports on ASUS PRIME B350M-A cease to
function after enabling runtime PM.
All boards with this chipsets will be affected, so revert the commit.
The original patch was added to stable 4.9, 4.11 and 4.12 and needs
to reverted from there as well
Cc: <stable@vger.kernel.org> # 4.9+
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A SuperSpeedPlus roothub needs to have the Link Protocol (LP) bit set in
the bmSublinkSpeedAttr[] entry of a SuperSpeedPlus descriptor.
If the xhci controller has an optional Protocol Speed ID (PSI) table then
that will be used as a base to create the roothub SuperSpeedPlus
descriptor.
The PSI table does not however necessary contain the LP bit so we need
to set it manually.
Check the psi speed and set LP bit if speed is 10Gbps or higher.
We're not setting it for 5 to 10Gbps as USB 3.1 specification always
mention SuperSpeedPlus for 10Gbps or higher, and some SSIC USB 3.0 speeds
can be over 5Gbps, such as SSIC-G3B-L1 at 5830 Mbps
Cc: <stable@vger.kernel.org> # 4.6+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To perform SuperSpeed compliance testing the port should first
be placed into compliance mode. For xHCI 1.0 and prior this
transition happens automatically when the port is in Training
and encounters an LFPS timeout. Thus running compliance tests
against a test appliance may simply just work by simply plugging
in to the downstream port.
However starting with xHCI 1.1 the transition from Polling.LFPS
to compliance mode may be disabled by default and needs to be
explicitly enabled by writing to the PLS field of the PORTSC
register, which sets an internal 'CTE' (Compliance Transition
Enabled) flag so that the port will perform the transition the
next time it encounters LFPS timeout. Whether this is disabled or
not is determined by the 'CTC' (Compliance Transition Capability)
bit in the HCCPARAMS2 capability register.
In order to allow a test operator to change this if needed, allow
a test driver (such as drivers/usb/misc/lvstest.c) to send a
SET_FEATURE(PORT_LINK_STATE) control message to the root hub to
update the link state prior to connecting to the port. Subsequently,
placing the port in warm reset would then disable the flag.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bus_resume() tried to resume the same ports the bus_suspend()
suspeded. This caused PLC timeouts in case a suspended device disconnected
and was not in a resumable state at bus_resume().
Add a check to make sure the link state is either U3 or resuming
before actually resuming the link.
At the same time do some other changes such as make sure we remove
wake on connect/disconnect/overcurrent also for the resuming ports,
and avoid extra portsc port register writes.
This improves resume time with 10ms in those PLC timeout cases where
devices disconnect at suspend/resume cycle.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both xhci_hub_control and xhci_disable_slot tries to hold spinlock, the
spinlock recursion occurs when enters USB2 test mode. Fix it by unlock
spinlock before calling xhci_disable_slot.
Cc: <stable@vger.kernel.org>
Fixes: 0f1d832ed1 ("usb: xhci: Add port test modes support for usb2")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A uncleared PLC (port link change) bit will prevent furuther port event
interrupts for that port. Leaving it uncleared caused get_port_status()
to timeout after 20000ms while waiting to get the final port event
interrupt for resume -> U0 state change.
This is a targeted fix for a specific case where we get a port resume event
racing with xhci resume. The port event interrupt handler notices xHC is
not yet running and bails out early, leaving PLC uncleared.
The whole xhci port resuming needs more attention, but while working on it
it anyways makes sense to always ensure PLC is cleared in get_port_status
before setting a new link state and waiting for its completion.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
on AMD platforms with SNPS 3.1 USB controller if stop endpoint command is
issued the controller does not respond, when the EP is not in running
state. HW completes the command execution and reports
"Context State Error" completion code. This is as per the spec. However
HW on receiving the second command additionally marks EP to Flow control
state in HW which is RTL bug. This bug causes the HW not to respond
to any further doorbells that are rung by the driver. This makes the EP
to not functional anymore and causes gross functional failures.
As a workaround, not to hit this problem, it's better to check the EP state
and issue a stop EP command only when the EP is in running state.
As a sidenote, even with this patch there is still a possibility of
triggering the RTL bug if the context state races with the stop endpoint
command as described in xHCI spec 4.6.9
[code simplification and reworded sidenote in commit message -Mathias]
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For AMD Promontory xHCI host, although you can disable USB 2.0 ports in
BIOS settings, those ports will be enabled anyway after you remove a
device on that port and re-plug it in again. It's a known limitation of
the chip. As a workaround we can clear the PORT_WAKE_BITS.
This will disable wake on connect, disconnect and overcurrent on
AMD Promontory USB2 ports
[checkpatch cleanup and commit message reword -Mathias]
Cc: <stable@vger.kernel.org>
Cc: Tsai Nicholas <nicholas.tsai@amd.com>
Signed-off-by: Jiahau Chang <Lars_Chang@asmedia.com.tw>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 4.11 TRB completion codes were renamed to match spec.
Completion codes for command ring stopped and endpoint stopped
were mixed, leading to failures while handling a stopped command ring.
Use the correct completion code for command ring stopped events.
Fixes: 0b7c105a04 ("usb: host: xhci: rename completion codes to match spec")
Cc: <stable@vger.kernel.org> # 4.11
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6ff6cbf1f ("usb: xhci: Add helper function xhci_set_power_on().")
created a helper to control port power that needs to be called with
xhci->lock held and interrupts disabled.
It released the lock with spin_unlock_irqrestore using a new zero flag
variable instead of the original flag from spin_lock_irqsave.
This regression triggered a static checker warning about bogus flags, and
a null pointer dereference on armada-385.
Fix it by passing a pointer to the correct flags and using it instead
Fixes: a6ff6cbf1f ("usb: xhci: Add helper function xhci_set_power_on().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Reported-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Tested-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a new xhci_hc_died() function that takes care of handling
pending commands and URBs if a host controller becomes unresponsive.
This addresses issues on hotpluggable xhci controllers that disappear
from the bus suddenly, often while the bus (PCI) remove function is
still being processed.
xhci_hc_died() sets a XHCI_STATUS_DYING flag to prevent new URBs and
commands or to be queued. The flag also ensures xhci_hc_died() will
give back pending commands and URBs once.
Host is considered dead if register read returns 0xffffffff, or host
fails to abort the command ring, or fails stopping an endpoint after
trying for 5 seconds.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For usb2 ports, the port test mode Test_J_State, Test_K_State,
Test_Packet, Test_SE0_NAK and Test_Force_En can be enabled
as described in usb2 spec.
USB2 test mode is a required hardware feature for system integrators
validating their hardware according to USB spec, regarding signal
strength and stuff. It is purely a hardware test feature.
Usually you need an oscilloscope and have to enable those test modes on
the hardware. This will send some specific test patterns on D+/D-. There
is no report available (in Linux itself) as it is purely externally
visible. Regular USB usage is not possible at that time.
Anyone (well access to e.g. /dev/bus/usb/001/001 provided) can use it by
sending appropriate USB_PORT_FEAT_TEST requests to the hub.
[Add better commit message by Alexander Stein -Mathias]
Signed-off-by: Guoqing Zhang <guoqing.zhang@intel.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactoring port power on/off related code into
a helper function xhci_set_power_on() which can
be reused when enabling test mode.
[set port state to neutral before writing port power -Mathias]
Signed-off-by: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's start tracing at least part of an xhci_virt_device lifetime. We
might want to extend this tracepoint class later, but for now it already
exposes quite a bit of valuable information.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cleanup only. This patch is a mechaninal rename to make sure our macros
for TRB completion codes match what the specification uses to refer to
such errors. The idea behind this is that it makes it far easier to grep
the specification and match it with implementation.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices from Texas Instruments [1] suffer from
a silicon bug where Port Enabled/Disabled bit
should not be used to silence an erroneous device.
The bug is so that if port is disabled with PED
bit, an IRQ for device removal (or attachment)
will never fire.
Just for the sake of completeness, the actual
problem lies with SNPS USB IP and this affects
all known versions up to 3.00a. A separate
patch will be added to dwc3 to enabled this
quirk flag if version is <= 3.00a.
[1] - AM572x Silicon Errata http://www.ti.com/lit/er/sprz429j/sprz429j.pdf
Section i896— USB xHCI Port Disable Feature Does Not Work
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman