Driver maintains different flags for WEP, WPA, WPA2 security modes.
Appropriate flag is set using security information provided in
connect request. mwifiex_is_network_compatible() routine uses them
to check if driver's setting is compatible with AP. Association is
aborted if the routine fails.
For some corner cases, it is observed that association is failed
even for valid security information based on association history.
This patch fixes the problem by clearing previous security setting
during each association.
We should set WEP key provided in connect request as default tx key.
This missing change is also added here.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most rate control implementations assume .get_rate and .tx_status are only
called once the per-station data has been fully initialized.
minstrel_ht crashes if this assumption is violated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are situations where we don't have the
necessary rate control information yet for
station entries, e.g. when associating. This
currently doesn't really happen due to the
dummy station handling; explicitly disabling
rate control when it's not initialised will
allow us to remove dummy stations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to use the _sync() version for cancelling the info and security
timer in the L2CAP connection delete path. Otherwise the delayed work
handler might run after the connection object is freed.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
__cancel_delayed_work() is being used in some paths where we cannot
sleep waiting for the delayed work to finish. However, that function
might return while the timer is running and the work will be queued
again. Replace the calls with safer cancel_delayed_work() version
which spins until the timer handler finishes on other CPUs and
cancels the delayed work.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We should only perform a reset in hci_dev_do_close if the
HCI_QUIRK_NO_RESET flag is set (since in such a case a reset will not be
performed when initializing the device).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
There is an imbalance in the rfcomm_session_hold / rfcomm_session_put
operations which causes the following crash:
[ 685.010159] BUG: unable to handle kernel paging request at 6b6b6b6b
[ 685.010169] IP: [<c149d76d>] rfcomm_process_dlcs+0x1b/0x15e
[ 685.010181] *pdpt = 000000002d665001 *pde = 0000000000000000
[ 685.010191] Oops: 0000 [#1] PREEMPT SMP
[ 685.010247]
[ 685.010255] Pid: 947, comm: krfcommd Tainted: G C 3.0.16-mid8-dirty #44
[ 685.010266] EIP: 0060:[<c149d76d>] EFLAGS: 00010246 CPU: 1
[ 685.010274] EIP is at rfcomm_process_dlcs+0x1b/0x15e
[ 685.010281] EAX: e79f551c EBX: 6b6b6b6b ECX: 00000007 EDX: e79f40b4
[ 685.010288] ESI: e79f4060 EDI: ed4e1f70 EBP: ed4e1f68 ESP: ed4e1f50
[ 685.010295] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 685.010303] Process krfcommd (pid: 947, ti=ed4e0000 task=ed43e5e0 task.ti=ed4e0000)
[ 685.010308] Stack:
[ 685.010312] ed4e1f68 c149eb53 e5925150 e79f4060 ed500000 ed4e1f70 ed4e1f80 c149ec10
[ 685.010331] 00000000 ed43e5e0 00000000 ed4e1f90 ed4e1f9c c149ec87 0000bf54 00000000
[ 685.010348] 00000000 ee03bf54 c149ec37 ed4e1fe4 c104fe01 00000000 00000000 00000000
[ 685.010367] Call Trace:
[ 685.010376] [<c149eb53>] ? rfcomm_process_rx+0x6e/0x74
[ 685.010387] [<c149ec10>] rfcomm_process_sessions+0xb7/0xde
[ 685.010398] [<c149ec87>] rfcomm_run+0x50/0x6d
[ 685.010409] [<c149ec37>] ? rfcomm_process_sessions+0xde/0xde
[ 685.010419] [<c104fe01>] kthread+0x63/0x68
[ 685.010431] [<c104fd9e>] ? __init_kthread_worker+0x42/0x42
[ 685.010442] [<c14dae82>] kernel_thread_helper+0x6/0xd
This issue has been brought up earlier here:
https://lkml.org/lkml/2011/5/21/127
The issue appears to be the rfcomm_session_put in rfcomm_recv_ua. This
operation doesn't seem be to required as for the non-initiator case we
have the rfcomm_process_rx doing an explicit put and in the initiator
case the last dlc_unlink will drive the reference counter to 0.
There have been several attempts to fix these issue:
6c2718d Bluetooth: Do not call rfcomm_session_put() for RFCOMM UA on closed socket
683d949 Bluetooth: Never deallocate a session when some DLC points to it
but AFAICS they do not fix the issue just make it harder to reproduce.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Gopala Krishna Murala <gopala.krishna.murala@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
queue_delayed_work() expects a relative time for when that work
should be scheduled.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
After moving L2CAP timers to workqueues l2cap_set_timer expects timeout
value to be specified in jiffies but constants defined in miliseconds
are used. This makes timeouts unreliable when CONFIG_HZ is not set to
1000.
__set_chan_timer macro still uses jiffies as input to avoid multiple
conversions from/to jiffies for sk_sndtimeo value which is already
specified in jiffies.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Ackec-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
sk_sndtime value should be specified in jiffies thus initial value
needs to be converted from miliseconds. Otherwise this timeout is
unreliable when CONFIG_HZ is not set to 1000.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
As reported by Dan Carpenter this function causes a Sparse warning and
shouldn't be declared inline:
include/net/bluetooth/l2cap.h:837:30 error: marked inline, but without a
definition"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
[ 2096.384084] btusb_send_frame:684: hci0
[ 2096.384087] usb 3-1: BOGUS urb flags, 2 --> 0
[ 2096.384091] Bluetooth: hci0 urb ffff8801b61d3a80 submission failed (22)
According the documentation in usb_submit_urb() URB_ISO_ASAP
flag is only allowed for endpoints of type USB_ENDPOINT_XFER_ISOC.
This reverts commit b8aabfc922.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Commit 330605423c fixed l2cap conn establishment for non-ssp remote
devices by not setting HCI_CONN_ENCRYPT_PEND every time conn security
is tested (which was always returning failure on any subsequent
security checks).
However, this broke l2cap conn establishment for ssp remote devices
when an ACL link was already established at SDP-level security. This
fix ensures that encryption must be pending whenever authentication
is also pending.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fixes problem where caller would think routine succeeded when it failed
leading to divide by zero panic.
Signed-off-by: Simon Graham <simon.graham@virtualcomputer.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
read_lock(&tpt_trig->trig.leddev_list_lock) is accessed via the path
ieee80211_open (->) ieee80211_do_open (->) ieee80211_mod_tpt_led_trig
(->) ieee80211_start_tpt_led_trig (->) tpt_trig_timer before initializing
it.
the intilization of this read/write lock happens via the path
ieee80211_led_init (->) led_trigger_register, but we are doing
'ieee80211_led_init' after 'ieeee80211_if_add' where we
register netdev_ops.
so we access leddev_list_lock before initializing it and causes the
following bug in chrome laptops with AR928X cards with the following
script
while true
do
sudo modprobe -v ath9k
sleep 3
sudo modprobe -r ath9k
sleep 3
done
BUG: rwlock bad magic on CPU#1, wpa_supplicant/358, f5b9eccc
Pid: 358, comm: wpa_supplicant Not tainted 3.0.13 #1
Call Trace:
[<8137b9df>] rwlock_bug+0x3d/0x47
[<81179830>] do_raw_read_lock+0x19/0x29
[<8137f063>] _raw_read_lock+0xd/0xf
[<f9081957>] tpt_trig_timer+0xc3/0x145 [mac80211]
[<f9081f3a>] ieee80211_mod_tpt_led_trig+0x152/0x174 [mac80211]
[<f9076a3f>] ieee80211_do_open+0x11e/0x42e [mac80211]
[<f9075390>] ? ieee80211_check_concurrent_iface+0x26/0x13c [mac80211]
[<f9076d97>] ieee80211_open+0x48/0x4c [mac80211]
[<812dbed8>] __dev_open+0x82/0xab
[<812dc0c9>] __dev_change_flags+0x9c/0x113
[<812dc1ae>] dev_change_flags+0x18/0x44
[<8132144f>] devinet_ioctl+0x243/0x51a
[<81321ba9>] inet_ioctl+0x93/0xac
[<812cc951>] sock_ioctl+0x1c6/0x1ea
[<812cc78b>] ? might_fault+0x20/0x20
[<810b1ebb>] do_vfs_ioctl+0x46e/0x4a2
[<810a6ebb>] ? fget_light+0x2f/0x70
[<812ce549>] ? sys_recvmsg+0x3e/0x48
[<810b1f35>] sys_ioctl+0x46/0x69
[<8137fa77>] sysenter_do_call+0x12/0x2
Cc: <stable@vger.kernel.org>
Cc: Gary Morain <gmorain@google.com>
Cc: Paul Stewart <pstew@google.com>
Cc: Abhijit Pradhan <abhijit@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Acked-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices (iwl5100) cannot connect to zd1211rw based AP. It appears that
zd1211 firmware messes up duration_id field if it is not set to zero by driver.
Sniffing traffic shows that zd1211 is transmitting frames with duration_id bits
14 and 15 set and other bits appearing random. Setting duration_id at driver to
zero results zd1211 outputting sane duration_id. This means that firmware is
setting correct values itself and expects duration_id to be zero in first
place.
Looking at vendor driver shows that only PSPoll frames have duration_id set by
driver, for other frames duration_id left zero.
Original bug-report and attached patch at:
http://sourceforge.net/mailarchive/message.php?msg_id=28759111
Reported-by: Tomas Vanek <Tomas.Vanek@fbl.cz>
[modified original patch from bug-report, added check for pspoll frame]
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The brcmsmac driver is now using the bcma SPROM CRC check, which does
not recognize all chipsets that were functional prior to the switch. In
particular, the current code bails out on odd CRC errors in recent
Macbooks. This patch ignores those errors, with the argument that an
unrecognized SPROM should be treated similarly to a non-existing one.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit adb5066 "ath9k_hw: do not apply the 2.4 ghz ack timeout
workaround to cts" reduced the hardware CTS timeout to the normal
values specified by the standard, but it turns out while it doesn't
need the same extra time that it needs for the ACK timeout, it
does need more than the value specified in the standard, but only
for 2.4 GHz.
This patch brings the CTS timeout value in sync with the initialization
values, while still allowing adjustment for bigger distances.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit b4a82a0 "ath9k_hw: fix interpretation of the rx KeyMiss flag"
fixed the interpretation of the KeyMiss flag for keycache based lookups,
however WEP encryption uses a static index, so KeyMiss is always asserted
for it, even though frames are decrypted properly.
Fix this by clearing the ATH9K_RXERR_KEYMISS flag if no keycache based
lookup was performed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Reported-by: Laurent Bonnans <bonnans.l@gmail.com>
Reported-by: Jurica Vukadin <u.ra604@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If driver load is failed, sometimes few pointers may remain
uninitialized ex. priv->wdev, priv->netdev, adapter->sleep_cfm
This will cause NULL pointer dereferance while unloading the
driver.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
all works need to be initialized before ieee80211_register_hw
to prevent mac80211 call backs such as drv_start, drv_config
getting started. otherwise we would queue/cancel works before
initializing them and it leads to kernel panic.
this issue can be recreated with the following script
in Chrome laptops with AR928X cards, with background scan
running (or) Network manager is running
while true
do
sudo modprobe -v ath9k
sleep 3
sudo modprobe -r ath9k
sleep 3
done
EIP: [<81040a47>] __cancel_work_timer+0xb8/0xe1 SS:ESP 0068:f6be9d70
---[ end trace 4f86d6139a9900ef ]---
Registered led device: ath9k-phy0
ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xf88a0000,
irq=16
Kernel panic - not syncing: Fatal exception
Pid: 456, comm: wpa_supplicant Tainted: G D
3.0.13 #1
Call Trace:
[<81379e21>] panic+0x53/0x14a
[<81004a30>] oops_end+0x73/0x81
[<81004b53>] die+0x4c/0x55
[<81002710>] do_trap+0x7c/0x83
[<81002855>] ? do_bounds+0x58/0x58
[<810028cc>] do_invalid_op+0x77/0x81
[<81040a47>] ? __cancel_work_timer+0xb8/0xe1
[<810489ec>] ? sched_clock_cpu+0x81/0x11f
[<8103f809>] ? wait_on_work+0xe2/0xf7
[<8137f807>] error_code+0x67/0x6c
[<810300d8>] ? wait_consider_task+0x4ba/0x84c
[<81040a47>] ? __cancel_work_timer+0xb8/0xe1
[<810380c9>] ? try_to_del_timer_sync+0x5f/0x67
[<81040a91>] cancel_work_sync+0xf/0x11
[<f88d7b7c>] ath_set_channel+0x62/0x25c [ath9k]
[<f88d67d1>] ? ath9k_tx_last_beacon+0x26a/0x85c [ath9k]
[<f88d8899>] ath_radio_disable+0x3f1/0x68e [ath9k]
[<f90d0edb>] ieee80211_hw_config+0x111/0x116 [mac80211]
[<f90dd95c>] __ieee80211_recalc_idle+0x919/0xa37 [mac80211]
[<f90dda76>] __ieee80211_recalc_idle+0xa33/0xa37 [mac80211]
[<812dbed8>] __dev_open+0x82/0xab
Cc: <stable@vger.kernel.org>
Cc: Gary Morain <gmorain@google.com>
Cc: Paul Stewart <pstew@google.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently even if association is failed "iw link" shows some
information about connected BSS and "Tx timeout" error is seen in
dmesg log.
This patch fixes below issues in the code to handle assoc failure
case correctly.
1) "status" variable in mwifiex_wait_queue_complete() is not
correctly updated. Hence driver doesn't inform cfg80211 stack
about association failure.
2) During association network queues are stopped but carrier is
not cleared, which gives Tx timeout error in failure case
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current code checks for stored_mpdu_num > 1, causing
the reorder_timer to be triggered indefinitely, but the
frame is never timed-out (until the next packet is received)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Cc: <stable@vger.kernel.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In my AMPDU rework, I rely on the sequence numbers of frames. But
I didn't check that the frame has a valid tid before updating the
tracking counters. As a result, the Tx queues were stalled. People
who hit this bug saw that we simply didn't let any data out.
This bug was introduced in 3.3.
This patch fixes that and checks that the frame is a QoS frame before
looking at its tid and changing the counters.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ssb supports one extra device on the cardbus. This results in two
devices in total, one beeing the host controller itself and the other
the external device connected to the hostcontroller over cardbus.
This makes the cardbus slot work on the Linksys WRT150N.
Reported-by: Aaron Z <aaronz@pls-net.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch correct the type of variables containing the rssi
values read from the rxwi.
In function rt2800_agc_to_rssi() 3 variables (rssi0, rssi1, rss2)
defined as int was assigned a 16bit signed values as unsigned.
From a test with a hi-gain antenna I verified that the rxwi
contains signed rssi values in the range -13/+81 (inclusive)
with 0 as an error condition. In case of negative values a
condition is triggered and the function return -128dBm while
the signal is at its maximum. This patch correct the cast so
negative values are not treated as very high positive values
(ex. -13 does not become 243).
Signed-off-by: Luigi Tarenga <luigi.tarenga@gmail.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma_bus_scan() leaks 'struct bcma_device' bytes if
bcma_get_next_core() returns error.
Restructure the code so we always kfree() the memory we allocate to
the variable 'core' before it goes out of scope.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 0884d7aa24 (AF_UNIX: Fix poll blocking problem when reading from
a stream socket) added a regression for epoll() in Edge Triggered mode
(EPOLLET)
Appropriate fix is to use skb_peek()/skb_unlink() instead of
skb_dequeue(), and only call skb_unlink() when skb is fully consumed.
This remove the need to requeue a partial skb into sk_receive_queue head
and the extra sk->sk_data_ready() calls that added the regression.
This is safe because once skb is given to sk_receive_queue, it is not
modified by a writer, and readers are serialized by u->readlock mutex.
This also reduce number of spinlock acquisition for small reads or
MSG_PEEK users so should improve overall performance.
Reported-by: Nick Mathewson <nickm@freehaven.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Alexey Moiseytsev <himeraster@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes tcp_trim_head() to recalculate the number of
segments in the skb with the skb's existing MSS, so trimming the head
causes the skb segment count to be monotonically non-increasing - it
should stay the same or go down, but not increase.
Previously tcp_trim_head() used the current MSS of the connection. But
if there was a decrease in MSS between original transmission and ACK
(e.g. due to PMTUD), this could cause tcp_trim_head() to
counter-intuitively increase the segment count when trimming bytes off
the head of an skb. This violated assumptions in tcp_tso_acked() that
tcp_trim_head() only decreases the packet count, so that packets_acked
in tcp_tso_acked() could underflow, leading tcp_clean_rtx_queue() to
pass u32 pkts_acked values as large as 0xffffffff to
ca_ops->pkts_acked().
As an aside, if tcp_trim_head() had really wanted the skb to reflect
the current MSS, it should have called tcp_set_skb_tso_segs()
unconditionally, since a decrease in MSS would mean that a
single-packet skb should now be sliced into multiple segments.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl_tcp_mem() initialization was moved to sysctl_tcp_ipv4.c
in commit 3dc43e3e4d, since it
became a per-ns value.
That code, however, will never run when CONFIG_SYSCTL is
disabled, leading to bogus values on those fields - causing hung
TCP sockets.
This patch fixes it by keeping an initialization code in
tcp_init(). It will be overwritten by the first net namespace
init if CONFIG_SYSCTL is compiled in, and do the right thing if
it is compiled out.
It is also named properly as tcp_init_mem(), to properly signal
its non-sysctl side effect on TCP limits.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Glauber Costa <glommer@parallels.com>
Cc: David S. Miller <davem@davemloft.net>
Link: http://lkml.kernel.org/r/4F22D05A.8030604@parallels.com
[ renamed the function, tidied up the changelog a bit ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
caif is a subsystem and as such it needs to register with
register_pernet_subsys instead of register_pernet_device.
Among other problems using register_pernet_device was resulting in
net_generic being called before the caif_net structure was allocated.
Which has been causing net_generic to fail with either BUG_ON's or by
return NULL pointers.
A more ugly problem that could be caused is packets in flight why the
subsystem is shutting down.
To remove confusion also remove the cruft cause by inappropriately
trying to fix this bug.
With the aid of the previous patch I have tested this patch and
confirmed that using register_pernet_subsys makes the failure go away as
it should.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By definition net_generic should never be called when it can return
NULL. Fail conspicously with a BUG_ON to make it clear when people mess
up that a NULL return should never happen.
Recently there was a bug in the CAIF subsystem where it was registered
with register_pernet_device instead of register_pernet_subsys. It was
erroneously concluded that net_generic could validly return NULL and
that net_assign_generic was buggy (when it was just inefficient).
Hopefully this BUG_ON will prevent people to coming to similar erroneous
conclusions in the futrue.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 36a1211970 removed linux/module.h
include statement from one of the headers that end up in net/sock.h.
It was providing us with static_branch() definition implicitly, so
after its removal the build got broken.
To fix this, and avoid having this happening in the future,
let me do the right thing and include linux/jump_label.h
explicitly in sock.h.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting link parameters on a netdevice changes the value
of if_nlmsg_size(), therefore it is necessary to recalculate
min_ifinfo_dump_size.
Signed-off-by: Stefan Gula <steweg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tunnel devices set NETIF_F_LLTX to bypass HARD_TX_LOCK. Sit and
ipip set this unconditionally in ops->setup, but gre enables it
conditionally after parameter passing in ops->newlink. This is
not called during tunnel setup as below, however, so GRE tunnels are
still taking the lock.
modprobe ip_gre
ip tunnel add test0 mode gre remote 10.5.1.1 dev lo
ip link set test0 up
ip addr add 10.6.0.1 dev test0
# cat /sys/class/net/test0/features
# $DIR/test_tunnel_xmit 10 10.5.2.1
ip route add 10.5.2.0/24 dev test0
ip tunnel del test0
The newlink callback is only called in rtnl_netlink, and only if
the device is new, as it calls register_netdevice internally. Gre
tunnels are created at 'ip tunnel add' with ioctl SIOCADDTUNNEL,
which calls ipgre_tunnel_locate, which calls register_netdev.
rtnl_newlink is called at 'ip link set', but skips ops->newlink
and the device is up with locking still enabled. The equivalent
ipip tunnel works fine, btw (just substitute 'method gre' for
'method ipip').
On kernels before /sys/class/net/*/features was removed [1],
the first commented out line returns 0x6000 with method gre,
which indicates that NETIF_F_LLTX (0x1000) is not set. With ipip,
it reports 0x7000. This test cannot be used on recent kernels where
the sysfs file is removed (and ETHTOOL_GFEATURES does not currently
work for tunnel devices, because they lack dev->ethtool_ops).
The second commented out line calls a simple transmission test [2]
that sends on 24 cores at maximum rate. Results of a single run:
ipip: 19,372,306
gre before patch: 4,839,753
gre after patch: 19,133,873
This patch replicates the condition check in ipgre_newlink to
ipgre_tunnel_locate. It works for me, both with oseq on and off.
This is the first time I looked at rtnetlink and iproute2 code,
though, so someone more knowledgeable should probably check the
patch. Thanks.
The tail of both functions is now identical, by the way. To avoid
code duplication, I'll be happy to rework this and merge the two.
[1] http://patchwork.ozlabs.org/patch/104610/
[2] http://kernel.googlecode.com/files/xmit_udp_parallel.c
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new net namespace is created, we should attach to it a "struct
net_generic" with enough slots (even empty), or we can hit the following
BUG_ON() :
[ 200.752016] kernel BUG at include/net/netns/generic.h:40!
...
[ 200.752016] [<ffffffff825c3cea>] ? get_cfcnfg+0x3a/0x180
[ 200.752016] [<ffffffff821cf0b0>] ? lockdep_rtnl_is_held+0x10/0x20
[ 200.752016] [<ffffffff825c41be>] caif_device_notify+0x2e/0x530
[ 200.752016] [<ffffffff810d61b7>] notifier_call_chain+0x67/0x110
[ 200.752016] [<ffffffff810d67c1>] raw_notifier_call_chain+0x11/0x20
[ 200.752016] [<ffffffff821bae82>] call_netdevice_notifiers+0x32/0x60
[ 200.752016] [<ffffffff821c2b26>] register_netdevice+0x196/0x300
[ 200.752016] [<ffffffff821c2ca9>] register_netdev+0x19/0x30
[ 200.752016] [<ffffffff81c1c67a>] loopback_net_init+0x4a/0xa0
[ 200.752016] [<ffffffff821b5e62>] ops_init+0x42/0x180
[ 200.752016] [<ffffffff821b600b>] setup_net+0x6b/0x100
[ 200.752016] [<ffffffff821b6466>] copy_net_ns+0x86/0x110
[ 200.752016] [<ffffffff810d5789>] create_new_namespaces+0xd9/0x190
net_alloc_generic() should take into account the maximum index into the
ptr array, as a subsystem might use net_generic() anytime.
This also reduces number of reallocations in net_assign_generic()
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sjur Brændeland <sjur.brandeland@stericsson.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port autoselection finds a port and then drop the lock,
then right after that, gets the hash bucket again and lock it.
Fix it to go direct.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code checks for conflicts when the application
requests a specific port. If there is no conflict, then
the request is granted.
On the other hand, the port autoselection done by the kernel
fails when all ports are bound even when there is a port
with no conflict available.
The fix changes port autoselection to check if there is a
conflict and use it if not.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet is received on an L2TP IP socket (L2TPv3 IP link
encapsulation), the l2tpip socket's backlog_rcv function calls
xfrm4_policy_check(). This is not necessary, since it was called
before the skb was added to the backlog. With CONFIG_NET_NS enabled,
xfrm4_policy_check() will oops if skb->dev is null, so this trivial
patch removes the call.
This bug has always been present, but only when CONFIG_NET_NS is
enabled does it cause problems. Most users are probably using UDP
encapsulation for L2TP, hence the problem has only recently
surfaced.
EIP: 0060:[<c12bb62b>] EFLAGS: 00210246 CPU: 0
EIP is at l2tp_ip_recvmsg+0xd4/0x2a7
EAX: 00000001 EBX: d77b5180 ECX: 00000000 EDX: 00200246
ESI: 00000000 EDI: d63cbd30 EBP: d63cbd18 ESP: d63cbcf4
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Call Trace:
[<c1218568>] sock_common_recvmsg+0x31/0x46
[<c1215c92>] __sock_recvmsg_nosec+0x45/0x4d
[<c12163a1>] __sock_recvmsg+0x31/0x3b
[<c1216828>] sock_recvmsg+0x96/0xab
[<c10b2693>] ? might_fault+0x47/0x81
[<c10b2693>] ? might_fault+0x47/0x81
[<c1167fd0>] ? _copy_from_user+0x31/0x115
[<c121e8c8>] ? copy_from_user+0x8/0xa
[<c121ebd6>] ? verify_iovec+0x3e/0x78
[<c1216604>] __sys_recvmsg+0x10a/0x1aa
[<c1216792>] ? sock_recvmsg+0x0/0xab
[<c105a99b>] ? __lock_acquire+0xbdf/0xbee
[<c12d5a99>] ? do_page_fault+0x193/0x375
[<c10d1200>] ? fcheck_files+0x9b/0xca
[<c10d1259>] ? fget_light+0x2a/0x9c
[<c1216bbb>] sys_recvmsg+0x2b/0x43
[<c1218145>] sys_socketcall+0x16d/0x1a5
[<c11679f0>] ? trace_hardirqs_on_thunk+0xc/0x10
[<c100305f>] sysenter_do_call+0x12/0x38
Code: c6 05 8c ea a8 c1 01 e8 0c d4 d9 ff 85 f6 74 07 3e ff 86 80 00 00 00 b9 17 b6 2b c1 ba 01 00 00 00 b8 78 ed 48 c1 e8 23 f6 d9 ff <ff> 76 0c 68 28 e3 30 c1 68 2d 44 41 c1 e8 89 57 01 00 83 c4 0c
Signed-off-by: James Chapman <jchapman@katalix.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davem says:
1) Fix JIT code generation on x86-64 for divide by zero, from Eric Dumazet.
2) tg3 header length computation correction from Eric Dumazet.
3) More build and reference counting fixes for socket memory cgroup
code from Glauber Costa.
4) module.h snuck back into a core header after all the hard work we
did to remove that, from Paul Gortmaker and Jesper Dangaard Brouer.
5) Fix PHY naming regression and add some new PCI IDs in stmmac, from
Alessandro Rubini.
6) Netlink message generation fix in new team driver, should only advertise
the entries that changed during events, from Jiri Pirko.
7) SRIOV VF registration and unregistration fixes, and also add a
missing PCI ID, from Roopa Prabhu.
8) Fix infinite loop in tx queue flush code of brcmsmac, from Stanislaw Gruszka.
9) ftgmac100/ftmac100 build fix, missing interrupt.h include.
10) Memory leak fix in net/hyperv do_set_mutlicast() handling, from Wei Yongjun.
11) Off by one fix in netem packet scheduler, from Vijay Subramanian.
12) TCP loss detection fix from Yuchung Cheng.
13) TCP reset packet MD5 calculation uses wrong address, fix from Shawn Lu.
14) skge carrier assertion and DMA mapping fixes from Stephen Hemminger.
15) Congestion recovery undo performed at the wrong spot in BIC and CUBIC
congestion control modules, fix from Neal Cardwell.
16) Ethtool ETHTOOL_GSSET_INFO is unnecessarily restrictive, from Michał Mirosław.
17) Fix triggerable race in ipv6 sysctl handling, from Francesco Ruggeri.
18) Statistics bug fixes in mlx4 from Eugenia Emantayev.
19) rds locking bug fix during info dumps, from your's truly.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
rds: Make rds_sock_lock BH rather than IRQ safe.
netprio_cgroup.h: dont include module.h from other includes
net: flow_dissector.c missing include linux/export.h
team: send only changed options/ports via netlink
net/hyperv: fix possible memory leak in do_set_multicast()
drivers/net: dsa/mv88e6xxx.c files need linux/module.h
stmmac: added PCI identifiers
llc: Fix race condition in llc_ui_recvmsg
stmmac: fix phy naming inconsistency
dsa: Add reporting of silicon revision for Marvell 88E6123/88E6161/88E6165 switches.
tg3: fix ipv6 header length computation
skge: add byte queue limit support
mv643xx_eth: Add Rx Discard and Rx Overrun statistics
bnx2x: fix compilation error with SOE in fw_dump
bnx2x: handle CHIP_REVISION during init_one
bnx2x: allow user to change ring size in ISCSI SD mode
bnx2x: fix Big-Endianess in ethtool -t
bnx2x: fixed ethtool statistics for MF modes
bnx2x: credit-leakage fixup on vlan_mac_del_all
macvlan: fix a possible use after free
...
rds_sock_info() triggers locking warnings because we try to perform a
local_bh_enable() (via sock_i_ino()) while hardware interrupts are
disabled (via taking rds_sock_lock).
There is no reason for rds_sock_lock to be a hardware IRQ disabling
lock, none of these access paths run in hardware interrupt context.
Therefore making it a BH disabling lock is safe and sufficient to
fix this bug.
Reported-by: Kumar Sanghvi <kumaras@chelsio.com>
Reported-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A considerable effort was invested in wiping out module.h
from being present in all the other standard includes. This
one leaked back in, but once again isn't strictly necessary,
so remove it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The file net/core/flow_dissector.c seems to be missing
including linux/export.h.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amitkumar Karwar