Adds UFS sysfs documentation for new entry wb_on.
[mkp: fix doc formatting]
Link: https://lore.kernel.org/r/20210119163847.20165-3-huobean@gmail.com
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fix format
Currently UFS WriteBooster driver uses clock scaling up/down to set WB
on/off. For the platforms which don't support UFSHCD_CAP_CLK_SCALING, WB
will be always on. Provide a sysfs attribute to enable/disable WB during
runtime. Write 1/0 to "wb_on" sysfs node to enable/disable UFS WB.
Link: https://lore.kernel.org/r/20210119163847.20165-2-huobean@gmail.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some SoCs require a single scatterlist entry for smaller than page size,
i.e. 4KB. When dispatching commands with more than one scatterlist entry
under 4KB in size the following behavior is observed:
A command to read a block range is dispatched with two scatterlist entries
that are named AAA and BBB. After dispatching, the host builds two PRDT
entries and during transmission, device sends just one DATA IN because
device doesn't care about host DMA. The host then transfers the combined
amount of data from start address of the area named AAA. As a consequence,
the area that follows AAA in memory would be corrupted.
|<------------->|
+-------+------------ +-------+
+ AAA + (corrupted) ... + BBB +
+-------+------------ +-------+
To avoid this we need to enforce page size alignment for sg entries.
Link: https://lore.kernel.org/r/56dddef94f60bd9466fd77e69f64bbbd657ed2a1.1611026909.git.kwmad.kim@samsung.com
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Once going into while-do loop, intr_status is already true, this
if-statement is redundant, remove it.
Link: https://lore.kernel.org/r/20210118201233.3043-1-huobean@gmail.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A block of code is indented one level too deeply, clean this up.
Link: https://lore.kernel.org/r/20210115095824.9170-1-colin.king@canonical.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Indentation does not match nesting level")
Correct the spelling of Nagle's name in a comment.
Link: https://lore.kernel.org/r/2921.1610694423@turing-police
Reviewed-by: Chaitanya Kulkarni <chiatanya.kulkarni@wdc.com>
Signed-off-by: Valdis Klētnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull in the 5.11 SCSI fixes branch to provide an updated baseline for
megaraid and hisi_sas. Both drivers received core changes in
v5.11-rc3.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for eh_should_retry_cmd callback in lpfc_template.
Link: https://lore.kernel.org/r/1609969748-17684-6-git-send-email-muneendra.kumar@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add store capability to the rport port_state using sysfs under
fc_remote_ports/rport-*/port_state.
With this the user can move the port_state from Marginal->Online and
Online->Marginal.
- Marginal: This interface will set SCMD_NORETRIES_ABORT bit in
scmd->state for all the pending I/Os on the SCSI device associated with
target port.
- Online: This interface will clear SCMD_NORETRIES_ABORT bit in
scmd->state for all the pending I/Os on the SCSI device associated with
target port.
The following interface is provided to set the port state to Marginal and
Online respectively:
echo "Marginal" >> /sys/class/fc_remote_ports/rport-X\:Y-Z/port_state
echo "Online" >> /sys/class/fc_remote_ports/rport-X\:Y-Z/port_state
Link: https://lore.kernel.org/r/1609969748-17684-5-git-send-email-muneendra.kumar@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a new interface, fc_eh_should_retry_cmd(), which checks if the cmd
should be retried or not by checking the rport state. If the rport state is
marginal it returns false to make sure there won't be any retries on the
cmd.
Make the fc_remote_port_delete(), fc_user_scan_tgt(), and
fc_timeout_deleted_rport() functions handle the new rport state.
Link: https://lore.kernel.org/r/1609969748-17684-4-git-send-email-muneendra.kumar@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a new optional routine, eh_should_retry_cmd(), in scsi_host_template
that allows the transport to decide if a cmd is retryable. Return true if
the transport is in a state the cmd should be retried on.
Update scmd_eh_abort_handler() and scsi_eh_flush_done_q() to both call
scsi_eh_should_retry_cmd() to check whether the command needs to be
retried.
The above changes were based on a patch by Mike Christie.
Link: https://lore.kernel.org/r/1609969748-17684-3-git-send-email-muneendra.kumar@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add code in scsi_result_to_blk_status to translate a new error
DID_TRANSPORT_MARGINAL to the corresponding blk_status_t i.e
BLK_STS_TRANSPORT.
Add DID_TRANSPORT_MARGINAL case to scsi_decide_disposition().
Link: https://lore.kernel.org/r/1609969748-17684-2-git-send-email-muneendra.kumar@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the various module parameter toggles for adjusting the MQ
characteristics at boot/load time as well as a device attribute for
changing the client scsi channel request amount.
Link: https://lore.kernel.org/r/20210114203148.246656-22-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Turn on MQ by default and set sane values for the upper limit on hw queues
for the SCSI host, and number of hw SCSI channels to request from the
partner VIOS.
Link: https://lore.kernel.org/r/20210114203148.246656-21-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Grab the queue and list lock for each Sub-CRQ and add any uncompleted
events to the host purge list.
Link: https://lore.kernel.org/r/20210114203148.246656-20-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In general the client needs to send Cancel MADs and task management
commands down the same channel as the command(s) intended to cancel or
abort. The client assigns cancel keys per LUN and thus must send a Cancel
down each channel commands were submitted for that LUN. Further, the client
then must wait for those cancel completions prior to submitting a LUN RESET
or ABORT TASK SET.
Add a cancel rsp iu syncronization field to the ibmvfc_queue struct such
that the cancel routine can sync the cancel response to each queue that
requires a cancel command. Build a list of each cancel event sent and wait
for the completion of each submitted cancel.
Link: https://lore.kernel.org/r/20210114203148.246656-19-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a helper routine for initializing a Cancel MAD. This will be useful for
a channelized client that needs to send Cancel commands down every channel
commands were sent for a particular LUN.
Link: https://lore.kernel.org/r/20210114203148.246656-18-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the ibmvfc client adapter requests channels it must submit a number of
Sub-CRQ handles matching the number of channels being requested. The VIOS
in its response will overwrite the actual number of channel resources
allocated which may be less than what was requested. The client then must
store the VIOS Sub-CRQ handle for each queue. This VIOS handle is needed as
a parameter with h_send_sub_crq().
Link: https://lore.kernel.org/r/20210114203148.246656-17-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When the client has negotiated the use of channels all vfcFrames are
required to go down a Sub-CRQ channel or it is a protocoal violation. If
the adapter state is channelized submit vfcFrames to the appropriate
Sub-CRQ via the h_send_sub_crq() helper.
Link: https://lore.kernel.org/r/20210114203148.246656-16-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Extract the hwq id from a SCSI command and store it in the ibmvfc_event
structure to identify which Sub-CRQ to send the command down when channels
are being utilized.
Link: https://lore.kernel.org/r/20210114203148.246656-15-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Previous patches have plumbed the necessary Sub-CRQ interface and channel
negotiation MADs to fully channelize via hardware backed queues.
Advertise client support via NPIV Login capability IBMVFC_CAN_USE_CHANNELS
when the client bits have MQ enabled via vhost->mq_enabled, or when
channels were already in use during a subsequent NPIV Login. The later is
required because channel support is only renegotiated after a CRQ pair is
broken. Simple NPIV Logout/Logins require the client to continue to
advertise the channel capability until the CRQ pair between the client is
broken.
Link: https://lore.kernel.org/r/20210114203148.246656-14-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
New NPIV_ENQUIRY_CHANNEL and NPIV_SETUP_CHANNEL management datagrams (MADs)
were defined in a previous patchset. If the client advertises a desire to
use channels and the partner VIOS is channel capable then the client must
proceed with channel enquiry to determine the maximum number of channels
the VIOS is capable of providing, and registering SubCRQs via channel setup
with the VIOS immediately following NPIV Login. This handshaking should not
be performed for subsequent NPIV Logins unless the CRQ connection has been
reset.
Implement these two new MADs and issue them following a successful NPIV
login where the VIOS has set the SUPPORT_CHANNELS capability bit in the
NPIV Login response.
Link: https://lore.kernel.org/r/20210114203148.246656-13-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create an irq mapping for the hw_irq number provided from phyp firmware.
Request an irq assigned our Sub-CRQ interrupt handler. Unmap these irqs at
Sub-CRQ teardown.
Link: https://lore.kernel.org/r/20210114203148.246656-12-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Simple handler that calls Sub-CRQ drain routine directly.
Link: https://lore.kernel.org/r/20210114203148.246656-11-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The logic for iterating over the Sub-CRQ responses is similiar to that of
the primary CRQ. Add the necessary handlers for processing those responses.
Link: https://lore.kernel.org/r/20210114203148.246656-10-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Each Sub-CRQ has its own interrupt. A hypercall is required to toggle the
IRQ state. Provide the necessary mechanism via a helper function.
Link: https://lore.kernel.org/r/20210114203148.246656-9-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allocate a set of Sub-CRQs in advance. During channel setup the client and
VIOS negotiate the number of queues the VIOS supports and the number that
the client desires to request. Its possible that the final channel
resources allocated is less than requested, but the client is still
responsible for sending handles for every queue it is hoping for.
Also, provide deallocation cleanup routines.
Link: https://lore.kernel.org/r/20210114203148.246656-8-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Subordinate Command Response Queues (Sub CRQ) are used in conjunction with
the primary CRQ when more than one queue is needed by the virtual I/O
adapter. Recent phyp firmware versions support Sub CRQ's with ibmvfc
adapters. This feature is a prerequisite for supporting multiple hardware
backed submission queues in the vfc adapter.
The Sub CRQ command element differs from the standard CRQ in that it is
32bytes long as opposed to 16bytes for the latter. Despite this extra
16bytes the ibmvfc protocol will use the original CRQ command element
mapped to the first 16bytes of the Sub CRQ element initially.
Add definitions for the Sub CRQ command element and queue.
Link: https://lore.kernel.org/r/20210114203148.246656-7-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sub-CRQs are registred with firmware via a hypercall. Abstract that
interface into a simpler helper function.
Link: https://lore.kernel.org/r/20210114203148.246656-6-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With the upcoming addition of Sub-CRQs the event pool size may vary
per-queue.
Add a size parameter to ibmvfc_init_event_pool() such that different size
event pools can be requested by ibmvfc_alloc_queue().
Link: https://lore.kernel.org/r/20210114203148.246656-5-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The event pool and CRQ used to be separate entities of the adapter host
structure and as such were allocated and freed independently of each
other. Recent work as defined a generic queue structure with an event pool
specific to each queue. As such the event pool for each queue shouldn't be
allocated/freed independently, but instead performed as part of the queue
allocation/free routines.
Move the calls to ibmvfc_event_pool_{init|free} into
ibmvfc_{alloc|free}_queue respectively. The only functional change here is
that the CRQ cannot be released in ibmvfc_remove until after the event pool
has been successfully purged since releasing the queue will also free the
event pool.
Link: https://lore.kernel.org/r/20210114203148.246656-4-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The next patch in this series reworks the event pool allocation calls to
happen within the individual queue allocation routines instead of as
independent calls.
Move the init/free routines earlier in ibmvfc.c to prevent undefined
reference errors when calling these functions from the queue allocation
code. No functional change.
Link: https://lore.kernel.org/r/20210114203148.246656-3-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce several new vhost fields for managing MQ state of the adapter as
well as initial defaults for MQ enablement.
Link: https://lore.kernel.org/r/20210114203148.246656-2-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
User layer may access sysfs nodes when system PM ops or error handling is
running. This can cause various problems. Rename eh_sem to host_sem and use
it to protect PM ops and error handling from user layer intervention.
Link: https://lore.kernel.org/r/1610594010-7254-3-git-send-email-cang@codeaurora.org
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During system resume/suspend, hba could be NULL. In this case, do not touch
eh_sem.
Fixes: 88a92d6ae4 ("scsi: ufs: Serialize eh_work with system PM events and async scan")
Link: https://lore.kernel.org/r/1610594010-7254-2-git-send-email-cang@codeaurora.org
Acked-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While testing live partition mobility, we have observed occasional crashes
of the Linux partition. What we've seen is that during the live migration,
for specific configurations with large amounts of memory, slow network
links, and workloads that are changing memory a lot, the partition can end
up being suspended for 30 seconds or longer. This resulted in the following
scenario:
CPU 0 CPU 1
------------------------------- ----------------------------------
scsi_queue_rq migration_store
-> blk_mq_start_request -> rtas_ibm_suspend_me
-> blk_add_timer -> on_each_cpu(rtas_percpu_suspend_me
_______________________________________V
|
V
-> IPI from CPU 1
-> rtas_percpu_suspend_me
-> __rtas_suspend_last_cpu
-- Linux partition suspended for > 30 seconds --
-> for_each_online_cpu(cpu)
plpar_hcall_norets(H_PROD
-> scsi_dispatch_cmd
-> scsi_times_out
-> scsi_abort_command
-> queue_delayed_work
-> ibmvfc_queuecommand_lck
-> ibmvfc_send_event
-> ibmvfc_send_crq
- returns H_CLOSED
<- returns SCSI_MLQUEUE_HOST_BUSY
-> __blk_mq_requeue_request
-> scmd_eh_abort_handler
-> scsi_try_to_abort_cmd
- returns SUCCESS
-> scsi_queue_insert
Normally, the SCMD_STATE_COMPLETE bit would protect against the command
completion and the timeout, but that doesn't work here, since we don't
check that at all in the SCSI_MLQUEUE_HOST_BUSY path.
In this case we end up calling scsi_queue_insert on a request that has
already been queued, or possibly even freed, and we crash.
The patch below simply increases the default I/O timeout to avoid this race
condition. This is also the timeout value that nearly all IBM SAN storage
recommends setting as the default value.
Link: https://lore.kernel.org/r/1610463998-19791-1-git-send-email-brking@linux.vnet.ibm.com
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The memory allocated with devm_kzalloc() is freed automatically no need to
explicitly call devm_kfree(). Delete it and save some instruction cycles.
Link: https://lore.kernel.org/r/20210112092128.19295-1-huobean@gmail.com
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following coccicheck warning:
./drivers/scsi/lpfc/lpfc_bsg.c:5392:5-29: WARNING: Comparison to bool
Link: https://lore.kernel.org/r/1610439893-64872-1-git-send-email-abaci-bugfix@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: YANG LI <abaci-bugfix@linux.alibaba.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kernel stack violation when getting unit_descriptor/wb_buf_alloc_units from
rpmb LUN. The reason is that the unit descriptor length is different per
LU.
The length of Normal LU is 45 while the one of rpmb LU is 35.
int ufshcd_read_desc_param(struct ufs_hba *hba, ...)
{
param_offset=41;
param_size=4;
buff_len=45;
...
buff_len=35 by rpmb LU;
if (is_kmalloc) {
/* Make sure we don't copy more data than available */
if (param_offset + param_size > buff_len)
param_size = buff_len - param_offset;
--> param_size = 250;
memcpy(param_read_buf, &desc_buf[param_offset], param_size);
--> memcpy(param_read_buf, desc_buf+41, 250);
[ 141.868974][ T9174] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: wb_buf_alloc_units_show+0x11c/0x11c
}
}
Link: https://lore.kernel.org/r/20210111095927.1830311-1-jaegeuk@kernel.org
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Mailbox Ch/dump ram extend expects mb register 10 to be set. If not
set/clear, firmware can pick up garbage from previous invocation of this
mailbox. Example: mctp dump can set mb10. On subsequent flash read which
use mailbox cmd Ch, mb10 can retain previous value.
Link: https://lore.kernel.org/r/20210111093134.1206-6-njavali@marvell.com
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This change will aid in debugging issues arising because of dropped frame,
DIF errors, queue full etc where debug level is not set.
Link: https://lore.kernel.org/r/20210111093134.1206-4-njavali@marvell.com
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bean Huo