This patch rewrite two test against NULL value with correct style.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The message about invalid speed does not state 1000 as a valid speed.
It is much simpler to said that the speed is invalid.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As said by checkpatch ENOSYS means 'invalid syscall nr' and nothing
else.
This patch replace ENOSYS by the more appropriate value EINVAL.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac_dma_reset function use an open coded of readl_poll_timeout().
Replace the open coded handling with the proper function.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac_mdio_busy_wait() function do the same job than
readl_poll_timeout().
So is is better to replace it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checkpatch complains about some code style problem on stmmac_mdio.c.
This patch fix them.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the checkpatch warning about asm/io.h.
Sorting all includes in the process.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the checkpatch warning about free software address.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix some typos in comments.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bus_setup function pointer is not used at all, this patch remove it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the define MAC_RNABLE_RX have a typo, rename it to MAC_ENABLE_RX
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cap the maximum (total) value size and bail out if larger than KMALLOC_MAX_SIZE
as otherwise it doesn't make any sense to proceed further, since we're
guaranteed to fail to allocate elements anyway in lpm_trie_node_alloc();
likleyhood of failure is still high for large values, though, similarly
as with htab case in non-prealloc.
Next, make sure that cost vars are really u64 instead of size_t, so that we
don't overflow on 32 bit and charge only tiny map.pages against memlock while
allowing huge max_entries; cap also the max cost like we do with other map
types.
Fixes: b95a5c4db0 ("bpf: add a longest prefix match trie map implementation")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug and cleans up tunnelid range size
calculation code by using consistent variable names
and checks in size calculation and fill functions.
tested for a few cases of vlan-vni range mappings:
(output from patched iproute2):
$bridge vlan showtunnel
port vid tunid
vxlan0 100-105 1000-1005
200 2000
210 2100
211-213 2100-2102
214 2104
216-217 2108-2109
219 2119
Fixes: efa5356b0d ("bridge: per vlan dst_metadata netlink support")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have many gro cells users, so lets move the code to avoid
duplication.
This creates a CONFIG_GRO_CELLS option.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/qualcomm/emac/emac-ethtool.c:155:49-50: Unneeded semicolon
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
CC: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LED Mode:
Microsemi PHY support 2 LEDs (LED[0] and LED[1]) to display different
status information that can be selected by setting LED mode.
LED Mode parameter (vsc8531, led-0-mode) and (vsc8531, led-1-mode) get
from Device Tree.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch doesn't affect how the code works.
My static checker complains that the mask and shift doesn't make sense
because 0xffffff << 16 goes beyond the end of 32 bits. It should be
0xffff instead but the existing code won't cause runtime bugs.
Also the casting here is not needed and not consistent with the rest of
the code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conflict was an interaction between a bug fix in the
netvsc driver in 'net' and an optimization of the RX path
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix smatch errors by not dereferencing iq pointer if it's NULL.
See http://marc.info/?l=kernel-janitors&m=148637299004834&w=2
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Load correct firmware in rtl8192ce wireless driver, from Jurij
Smakov.
2) Fix leak of tx_ring and tx_cq due to overwriting in mlx4 driver,
from Martin KaFai Lau.
3) Need to reference count PHY driver module when it is attached, from
Mao Wenan.
4) Don't do zero length vzalloc() in ethtool register dump, from
Stanislaw Gruszka.
5) Defer net_disable_timestamp() to a workqueue to get out of locking
issues, from Eric Dumazet.
6) We cannot drop the SKB dst when IP options refer to them, fix also
from Eric Dumazet.
7) Incorrect packet header offset calculations in ip6_gre, again from
Eric Dumazet.
8) Missing tcp_v6_restore_cb() causes use-after-free, from Eric too.
9) tcp_splice_read() can get into an infinite loop with URG, and hey
it's from Eric once more.
10) vnet_hdr_sz can change asynchronously, so read it once during
decision making in macvtap and tun, from Willem de Bruijn.
11) Can't use kernel stack for DMA transfers in USB networking drivers,
from Ben Hutchings.
12) Handle csum errors properly in UDP by calling the proper destructor,
from Eric Dumazet.
13) For non-deterministic softirq run when scheduling NAPI from a
workqueue in mlx4, from Benjamin Poirier.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (28 commits)
sctp: check af before verify address in sctp_addr_id2transport
sctp: avoid BUG_ON on sctp_wait_for_sndbuf
mlx4: Invoke softirqs after napi_reschedule
udp: properly cope with csum errors
catc: Use heap buffer for memory size test
catc: Combine failure cleanup code in catc_probe()
rtl8150: Use heap buffers for all register access
pegasus: Use heap buffers for all register access
macvtap: read vnet_hdr_size once
tun: read vnet_hdr_sz once
tcp: avoid infinite loop in tcp_splice_read()
hns: avoid stack overflow with CONFIG_KASAN
ipv6: Fix IPv6 packet loss in scenarios involving roaming + snooping switches
ipv6: tcp: add a missing tcp_v6_restore_cb()
nl80211: Fix mesh HT operation check
mac80211: Fix adding of mesh vendor IEs
mac80211: Allocate a sync skcipher explicitly for FILS AEAD
mac80211: Fix FILS AEAD protection in Association Request frame
ip6_gre: fix ip6gre_err() invalid reads
netlabel: out of bound access in cipso_v4_validate()
...
Commit 6326fec112 ("mm: Use owner_priv bit for PageSwapCache, valid
when PageSwapBacked") aliased PG_swapcache to PG_owner_priv_1 (and
depending on PageSwapBacked being true).
As a result, the KPF_SWAPCACHE bit in '/proc/kpageflags' should now be
synthesized, instead of being shown on unrelated pages which just happen
to have PG_owner_priv_1 set.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiffies is volatile so read it once.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vtbegin should not be NULL in this function, Its already checked by the
caller.
this should silence the below smatch complaint:
net/bridge/br_netlink_tunnel.c:144 br_fill_vlan_tinfo_range()
error: we previously assumed 'vtbegin' could be null (see line 130)
net/bridge/br_netlink_tunnel.c
129
130 if (vtbegin && vtend && (vtend->vid - vtbegin->vid) > 0) {
^^^^^^^
Check for NULL.
Fixes: efa5356b0d ("bridge: per vlan dst_metadata netlink support")
Reported-By: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__packed is considered harmful as it potentially generates code that
doesn't perform well and its usage should be avoided as much as
possible.
This patch drops __packed from all SCTP structures except one, which is
sctp_signed_cookie. In there it's required, as per changelog on
commit 9834a2bb49 ("[SCTP]: Fix sctp_cookie alignment in the packet.").
After this patch, no alignment changes neither in x86 or x86_64 and
no exceptions were noticed during testing on both archs.
Code size for SCTP module also didn't change with this patch.
Cc: David Miller <davem@davemloft.net>
Cc: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6f29a13061 ("sctp: sctp_addr_id2transport should verify the
addr before looking up assoc") invoked sctp_verify_addr to verify the
addr.
But it didn't check af variable beforehand, once users pass an address
with family = 0 through sockopt, sctp_get_af_specific will return NULL
and NULL pointer dereference will be caused by af->sockaddr_len.
This patch is to fix it by returning NULL if af variable is NULL.
Fixes: 6f29a13061 ("sctp: sctp_addr_id2transport should verify the addr before looking up assoc")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These checks should go after the attributes have been parsed otherwise
we're using tb uninitialized.
Fixes: efa5356b0d ("bridge: per vlan dst_metadata netlink support")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error check on err is redundant as it is being checked
previously each time it has been updated. Remove this redundant
check.
Detected with CoverityScan, CID#140030("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bug is harmless because it's just a sanity check and we always
pass valid values for "encap_type" but the test is off by one.
Fixes: 9b41080125 ("sfc: insert catch-all filters for encapsulated traffic")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DP83867 when not properly bootstrapped - especially with LED_0 pin -
can enter N/A MODE4 for "port mirroring" feature.
To provide normal operation of the PHY, one needs not only to explicitly
disable the port mirroring feature, but as well stop some IC internal
testing (which disables RGMII communication).
To do that the STRAP_STS1 (0x006E) register must be read and RESERVED bit
11 examined. When it is set, the another RESERVED bit (11) at PHYCR
(0x0010) register must be clear to disable testing mode and enable RGMII
communication.
Thorough explanation of the problem can be found at following e2e thread:
"DP83867IR: Problem with RESERVED bits in PHY Control Register (PHYCR) -
Linux driver"
https://e2e.ti.com/support/interface/ethernet/f/903/p/571313/2096954#2096954
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for enabling or disabling the lane swapping (called
"port mirroring" in PHY's CFG4 register) feature of the DP83867 TI's PHY
device.
One use case is when bootstrap configuration enables this feature (because
of e.g. LED_0 wrong wiring) so then one needs to disable it in software
(at u-boot/Linux).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the documentation to avoid PHY lane swapping. This is a boolean
entry to notify the phy device drivers that the TX/RX lanes NO need
to be swapped.
The use case for this binding mostly happens after wrong HW
configuration of PHY IC during bootstrap.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: Incorrect use of phy_read_status()
This patch series removes incorrect uses of phy_read_status() which can clobber
the PHY device link while we are executing with the state machine running.
greth was potentially another candidate, but it does funky stuff with
auto-negotation that I am still trying to understand.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling phy_read_status() means that we may call into
genphy_read_status() which in turn will use genphy_update_link() which
can make changes to phydev->link outside of the state machine's state
transitions. This is an invalid behavior that is now caught as of
811a919135 ("phy state machine: failsafe leave invalid RUNNING state")
Reported-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling phy_read_status() means that we may call into
genphy_read_status() which in turn will use genphy_update_link() which
can make changes to phydev->link outside of the state machine's state
transitions. This is an invalid behavior that is now caught as off
811a919135 ("phy state machine: failsafe leave invalid RUNNING state")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling phy_read_status() means that we may call into
genphy_read_status() which in turn will use genphy_update_link() which
can make changes to phydev->link outside of the state machine's state
transitions. This is an invalid behavior that is now caught as of
811a919135 ("phy state machine: failsafe leave invalid RUNNING state")
Since we don't have anything special, switch to the generic
phy_ethtool_get_link_ksettings() function now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling phy_read_status() means that we may call into
genphy_read_status() which in turn will use genphy_update_link() which
can make changes to phydev->link outside of the state machine's state
transitions. This is an invalid behavior that is now caught as of
811a919135 ("phy state machine: failsafe leave invalid RUNNING state")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes some updates to mlx5 core and ethernet driver.
We got one patch from Or to fix some static checker warnings.
2nd patche from Dan came to add the support for 128B cache line
in the HCA, which will configures the hardware to use 128B alignment only
on systems with 128B cache lines, otherwise it will be kept as the current
default of 64B.
From me three patches to support no inline copy on TX on ConnectX-5 and
later HCAs. Starting with two small infrastructure changes and
refactoring patches followed by two patches to add the actual support for
both xmit ndo and XDP xmit routines.
Last patch is a simple fix to return a mistakenly removed pointer from the
SQ structure, which was remove in previous submission of mlx5 4K UAR.
Saeed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYmQKaAAoJEEg/ir3gV/o+RBMH/RGHNw3yPB2MyWo28V3eabw+
xl/SymiNOUgmq03ULYoc6xJpi9RCya7m/Kyce1M/M1gSz6LXubG2IDw9QsKV8lnc
+5rwHCKjop6MdR3khsgqvWqGiKfQN0+QON5MjlPZB3/4u8qFcjauhfXpiX9naMO5
aB/Sm9zRPwRnsEhy2AwPyZqOxe5boZzHqmZxpthIgPMtqbpBYNkTkooljsj/KqXf
AO3y/mdGykELPF3lIHTE4X9zixx5s6MrlAYX2uGUrAojs2WVIBsq3iXI/J8X9zs/
lg7to15WoMttR66vRZ120U6tx17OMmoxuAp+bmgZumabi/wDAZGSy5ELbH28WlY=
=F+t/
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-01-31' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-01-31
This series includes some updates to mlx5 core and ethernet driver.
We got one patch from Or to fix some static checker warnings.
2nd patche from Dan came to add the support for 128B cache line
in the HCA, which will configures the hardware to use 128B alignment only
on systems with 128B cache lines, otherwise it will be kept as the current
default of 64B.
From me three patches to support no inline copy on TX on ConnectX-5 and
later HCAs. Starting with two small infrastructure changes and
refactoring patches followed by two patches to add the actual support for
both xmit ndo and XDP xmit routines.
Last patch is a simple fix to return a mistakenly removed pointer from the
SQ structure, which was remove in previous submission of mlx5 4K UAR.
Saeed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to update jiffies in txq->trans_start twice, it's supposed to be
done in netdev_start_xmit() and anyway is re-written. Also, no reason to
update trans time in case of an error.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Add XDP support.
The first 10 patches refactor the code (rx/tx code paths and ring logic)
and add the basic infrastructure to support XDP. The 11th patch adds
basic ndo_xdp to support XDP_DROP and XDP_PASS only. The 12th patch
completes the series with XDP_TX.
Thanks to Andy Gospodarek for testing and uncovering some bugs.
v3: Removed Kconfig option.
Pass modified offset and length to stack for XDP_PASS.
Improved buffer recycling scheme for XDP_TX.
Other minor fixes.
v2: Addressed review comments from Alexei Starovoitov, Jakub Kicinski,
and David Miller:
- Added missing dma syncs.
- Added XDP headroom support.
- Added tracing in exception path.
- Clarified a parameter change.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dedicated transmit function and transmit completion handler for
XDP. The XDP transmit logic and completion logic are different than
regular TX ring. The TX buffer is recycled back to the RX ring when
it completes.
v3: Improved the buffer recyling scheme for XDP_TX.
v2: Add trace_xdp_exception().
Add dma_sync.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic ndo_xdp support to setup and query program, configure the NIC
to run in rx page mode, and support XDP_PASS, XDP_DROP, XDP_ABORTED
actions only.
v3: Pass modified offset and length to stack for XDP_PASS.
Remove Kconfig option.
v2: Added trace_xdp_exception()
Added dma_syncs.
Added XDP headroom support.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP_TX requires a different function to handle completion. Add a
function pointer to handle tx completion logic. Regular TX rings
will be assigned the current bnxt_tx_int() for the ->tx_int()
function pointer.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add logic for an extra set of TX rings for XDP. If enabled, this
set of TX rings equals the number of RX rings and shares the same
IRQ as the RX ring set. A new field bp->tx_nr_rings_xdp is added
to keep track of these TX XDP rings. Adjust all other relevant functions
to handle bp->tx_nr_rings_xdp.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support XDP_TX, we need to add a set of dedicated TX rings, each
associated with the NAPI of an RX ring. To assign XDP rings and regular
rings in a flexible way, we add a bp->tx_ring_map[] array to do the
remapping. The netdev txq index is stored in the new field txq_index
so that we can retrieve the netdev txq when handling TX completions.
In this patch, before we introduce XDP_TX, the mapping is 1:1.
v2: Fixed a bug in bnxt_tx_int().
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, bnxt_setup_tc() and bnxt_set_channels() have similar and
duplicated code to check and reserve rx and tx rings. Add a new
function bnxt_reserve_rings() to centralize the logic. This will
make it easier to add XDP_TX support which requires allocating a
new set of TX rings.
Also, the tx ring checking logic in bnxt_setup_msix() can be removed.
The rings have been reserved before hand.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current code, we have separate rx_event and agg_event parameters
to keep track of rx and aggregation events. Combine these events into
an u8 event mask with different bits defined for different events. This
way, it is easier to expand the logic to include XDP tx events.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This mode is to support XDP. In this mode, each rx ring is configured
with page sized buffers for linear placement of each packet. MTU will be
restricted to what the page sized buffers can support.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the global constants BNXT_RX_OFFSET and BNXT_RX_DMA_OFFSET to
device parameters. This will make it easier to support XDP with
headroom support which requires different RX buffer offsets.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LABBE Corentin