Ville figured out that it needs a full display reset since apparently
a lot more goes down than just the GT. Until that's address it's
better to just diable gpu reset.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So apparently this is tricky.
We need to consider:
- We start out with all the hw enabling bits disabled, both the
individual fifo underrun interrupts and the shared display error
interrupts masked. Otherwise if the bios config is broken we'll blow
up with a NULL deref in our interrupt handler since the crtc
structures aren't set up yet at driver load time.
- On gmch we need to mask fifo underruns on the sw side, so always
need to set that in sanitize_crtc for those platforms.
- On other platforms we try to set the sw tracking so that it reflects
the real state. But since a few platforms have shared bits we must
_not_ disable fifo underrun reporting. Otherwise we'll never enable
the shared error interrupt.
This is the state before out patch, but unfortunately this is not good
enough. But after a suspend resume operation this is broken:
1. We don't enable the hw interrupts since the same code runs on
resume as on driver load.
2. The fifo underrun state adjustments we do in sanitize_crtc doesn't
fire on resume since (except for hilarious firmware) all pipes are off
at that point. But they also don't hurt since the subsequent crtc
enabling due to force_restore will enable fifo underruns.
Which means when we enable fifo underrun reporting we notice that the
per-crtc state is already correct and short-circuit everthing out. And
the interrupt doesn't get enabled.
A similar problem would happen if the bios doesn't light up anything
when the driver loads. Which is exactly what happens when we reload
the driver since our unload functions disables all outputs.
Now we can't just rip out the short-circuit logic and unconditionally
update the fifo underrun reporting interrupt masking: We have some
checks for shared error interrupts to catch issues that happened when
the shared error interrupt was disabled.
The right fix is to push down this logic so that we can always update
the hardware state, but only check for missed fifo underruns on a real
enabled->disabled transition and ignore them when we're already
disabled.
On platforms with shared error interrupt the pipe CRC interrupts are
grouped together with the fifo underrun reporting this fixes pipe CRC
support after suspend and driver reloads.
Testcase: igt/kms_pipe_crc_basic/suspend-*
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On platforms with shared interrupt enable bits (which are shared even
with the pipe CRC logic) there's some tricky corner cases. Add
information to make debugging those easier.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All drm_fb_helper_restore_fbdev_mode() call sites, save one, do the same
locking. Simplify this into drm_fb_helper_restore_fbdev_mode_unlocked().
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For atomic, it will be quite necessary to not need to care so much
about locking order. And 'state' gives us a convenient place to stash a
ww_ctx for any sort of update that needs to grab multiple crtc locks.
Because we will want to eventually make locking even more fine grained
(giving locks to planes, connectors, etc), split out drm_modeset_lock
and drm_modeset_acquire_ctx to track acquired locks.
Atomic will use this to keep track of which locks have been acquired
in a transaction.
v1: original
v2: remove a few things not needed until atomic, for now
v3: update for v3 of connection_mutex patch..
v4: squash in docbook
v5: doc tweaks/fixes
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This should avoid races between connector probing and HPD
irqs in the future, currently mode_config.mutex blocks this
possibility.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull drm fixes from Dave Airlie:
"All fairly small: radeon stability and a panic path fix.
Mostly radeon fixes, suspend/resume fix, stability on the CIK
chipsets, along with a locking check avoidance patch for panic times
regression"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: use the CP DMA on CIK
drm/radeon: sync page table updates
drm/radeon: fix vm buffer size estimation
drm/crtc-helper: skip locking checks in panicking path
drm/radeon/dpm: resume fixes for some systems
Just flushing out my pile of random drm patches for the merge window,
nothing big. And it all hung around in drm-intel trees for a while (only
just rebased now).
* tag 'topic/core-stuff-2014-06-02' of git://anongit.freedesktop.org/drm-intel:
imx-drm: imx-tve: remove unused variable
drm: Missed clflushopt in drm_clflush_virt_range
drm/plane: Fix a couple of checkpatch warnings
drm/plane: Fix sparse warnings
drm/exynos: Fix double locks at PM resume
drm/ast: Fix double lock at PM resume
drm/dp-helper: Deprecate old i2c-over-dp_aux heleprs
Pretty small pull this time around for msm. Adds some useful debugfs
I'd been carrying around on a branch for a while, plus few fixes. And
Kconfig update for the great ARCH_MSM -> ARCH_QCOM split.
* 'msm-next' of git://people.freedesktop.org/~robclark/linux:
drm/msm: use correct gfp flag for vram allocation
drm/msm/mdp5: fix error return value
drm/msm: remove redundant private plane cleanup
drm/msm: add perf logging debugfs
drm/msm: add rd logging debugfs
drm/msm: update for ARCH_MSM -> ARCH_QCOM
drm/msm/hdmi: use gpio and HPD polling
drm/msm/mdp5: fix crash in error/unload paths
The drm core shouldn't depend upon any helpers, and we make sure this
doesn't accidentally happen by moving them into the helper-only
drm_kms_helper.ko module.
v2: Don't break the build for vmwgfx, spotted by Matt.
v3: Unbreak the depency loop around CONFIG_FB (not actually a loop
since it involves select). Reported by Chris.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The first one is a one liner fixing a stupid typo in the VM handling code and is only relevant if play with one of the VM defines.
The other two switches CIK to use the CPDMA instead of the SDMA for buffer moves, as it turned out the SDMA is still sometimes not 100% reliable.
* 'drm-fixes-3.15' of git://people.freedesktop.org/~deathsimple/linux:
drm/radeon: use the CP DMA on CIK
drm/radeon: sync page table updates
drm/radeon: fix vm buffer size estimation
After the split-out of crtc locks from the big mode_config.mutex
there's still two major areas it protects:
- Various connector probe states, like connector->status, EDID
properties, probed mode lists and similar information.
- The links from connector->encoder and encoder->crtc and other
modeset-relevant connector state (e.g. properties which control the
panel fitter).
The later is used by modeset operations. But they don't really care
about the former since it's allowed to e.g. enable a disconnected VGA
output or with a mode not in the probed list.
Thus far this hasn't been a problem, but for the atomic modeset
conversion Rob Clark needs to convert all modeset relevant locks into
w/w locks. This is required because the order of acquisition is
determined by how userspace supplies the atomic modeset data. This has
run into troubles in the detect path since the i915 load detect code
needs _both_ protections offered by the mode_config.mutex: It updates
probe state and it needs to change the modeset configuration to enable
the temporary load detect pipe.
The big deal here is that for the probe/detect users of this lock a
plain mutex fits best, but for atomic modesets we really want a w/w
mutex. To fix this lets split out a new connection_mutex lock for the
modeset relevant parts.
For simplicity I've decided to only add one additional lock for all
connector/encoder links and modeset configuration states. We have
piles of different modeset objects in addition to those (like bridges
or panels), so adding per-object locks would be much more effort.
Also, we're guaranteed (at least for now) to do a full modeset if we
need to acquire this lock. Which means that fine-grained locking is
fairly irrelevant compared to the amount of time the full modeset will
take.
I've done a full audit, and there's just a few things that justify
special focus:
- Locking in drm_sysfs.c is almost completely absent. We should
sprinkle mode_config.connection_mutex over this file a bit, but
since it already lacks mode_config.mutex this patch wont make the
situation any worse. This is material for a follow-up patch.
- omap has a omap_framebuffer_flush function which walks the
connector->encoder->crtc links and is called from many contexts.
Some look like they don't acquire mode_config.mutex, so this is
already racy. Again fixing this is material for a separate patch.
- The radeon hot_plug function to retrain DP links looks at
connector->dpms. Currently this happens without any locking, so is
already racy. I think radeon_hotplug_work_func should gain
mutex_lock/unlock calls for the mode_config.connection_mutex.
- Same applies to i915's intel_dp_hot_plug. But again, this is already
racy.
- i915 load_detect code needs to acquire this lock. Which means the
w/w dance due to Rob's work will be nicely contained to _just_ this
function.
I've added fixme comments everywhere where it looks suspicious but in
the sysfs code. After a quick irc discussion with Dave Airlie it
sounds like the lack of locking in there is due to sysfs cleanup fun
at module unload.
v1: original (only compile tested)
v2: missing mutex_init(), etc (from Rob Clark)
v3: i915 needs more care in the conversion:
- Protect the edp pp logic with the connection_mutex.
- Use connection_mutex in the backlight code due to
get_pipe_from_connector.
- Use drm_modeset_lock_all in suspend/resume paths.
- Update lock checks in the overlay code.
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
I find myself making this change locally whenever debugging FB reference
counting. Which seems a bit silly.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
An object property is an id (idr) for a drm mode object. This
will allow a property to be used set/get a framebuffer, CRTC, etc.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we continue to use bitmask for type, we will quickly run out of room
to add new types. Split this up so existing part of bitmask range
continues to function as before, but reserve a chunk of the remaining
space for an integer type-id. Wrap this all up in some type-check
helpers to keep the backwards-compat uglyness contained.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No longer used or needed as the structs have a name field.
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
spice-server and downstream code expect that the primary surface
will always have surface_id = 0, while in reality, once allocated, the
surface_id in qxl.ko is NEVER 0. In a dual head environment, all
monitors render portions of the primary surface.
However, when the monitor config events are generated and sent,
the primary surface is only mapped to the correct identifier
(i.e. 0) for the primary head (where crtc index is 0).
The fix is to look at the "primary" flag in the bo and always
use id 0, irrespective of which head is being configured.
[airlied: qxl hw really needs to be fixed to scanout surfaces]
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead of trying to flip inside the vblank period when
the buffer is idle, offload blocking for idle to a kernel
thread and program the flip directly into the hardware.
v2: add error handling, fix EBUSY handling
v3: add proper exclusive_lock handling
v4: update crtc->primary->fb when the flip actually happens
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A few addition of HD-audio fixups for ALC260 and AD1986A codecs.
All marked as stable fixes.
The fixes are pretty local and they are old machines, so quite safe
to apply.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=BSlJ
-----END PGP SIGNATURE-----
Merge tag 'sound-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A few addition of HD-audio fixups for ALC260 and AD1986A codecs. All
marked as stable fixes.
The fixes are pretty local and they are old machines, so quite safe to
apply"
* tag 'sound-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fix COEF widget NID for ALC260 replacer fixup
ALSA: hda/realtek - Correction of fixup codes for PB V7900 laptop
ALSA: hda/analog - Fix silent output on ASUS A8JN
There is still one residue of sysfs remaining: the sb_magic
SYSFS_MAGIC. However this should be kernfs user specific,
so this patch moves it out. Kerrnfs user should specify their
magic number while mouting.
Signed-off-by: Jianyu Zhan <nasa4836@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) Unbreak zebra and other netlink apps, from Eric W Biederman.
2) Some new qmi_wwan device IDs, from Aleksander Morgado.
3) Fix info leak in DCB netlink handler of qlcnic driver, from Dan
Carpenter.
4) inet_getid() and ipv6_select_ident() do not generate monotonically
increasing ID numbers, fix from Eric Dumazet.
5) Fix memory leak in __sk_prepare_filter(), from Leon Yu.
6) Netlink leftover bytes warning message is user triggerable, rate
limit it. From Michal Schmidt.
7) Fix non-linear SKB panic in ipvs, from Peter Christensen.
8) Congestion window undo needs to be performed even if only never
retransmitted data is SACK'd, fix from Yuching Cheng.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (24 commits)
net: filter: fix possible memory leak in __sk_prepare_filter()
net: ec_bhf: Add runtime dependencies
tcp: fix cwnd undo on DSACK in F-RTO
netlink: Only check file credentials for implicit destinations
ipheth: Add support for iPad 2 and iPad 3
team: fix mtu setting
net: fix inet_getid() and ipv6_select_ident() bugs
net: qmi_wwan: interface #11 in Sierra Wireless MC73xx is not QMI
net: qmi_wwan: add additional Sierra Wireless QMI devices
bridge: Prevent insertion of FDB entry with disallowed vlan
netlink: rate-limit leftover bytes warning and print process name
bridge: notify user space after fdb update
net: qmi_wwan: add Netgear AirCard 341U
net: fix wrong mac_len calculation for vlans
batman-adv: fix NULL pointer dereferences
net/mlx4_core: Reset RoCE VF gids when guest driver goes down
emac: aggregation of v1-2 PLB errors for IER register
emac: add missing support of 10mbit in emac/rgmii
can: only rename enabled led triggers when changing the netdev name
ipvs: Fix panic due to non-linear skb
...
__sk_prepare_filter() was reworked in commit bd4cf0ed3 (net: filter:
rework/optimize internal BPF interpreter's instruction set) so that it should
have uncharged memory once things went wrong. However that work isn't complete.
Error is handled only in __sk_migrate_filter() while memory can still leak in
the error path right after sk_chk_filter().
Fixes: bd4cf0ed33 ("net: filter: rework/optimize internal BPF interpreter's instruction set")
Signed-off-by: Leon Yu <chianglungyu@gmail.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Tested-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Highlights:
- GPUVM opimtizations
- HDMI audio cleanups
- Deep color HDMI support
- more bug fixes, cleanups
* 'drm-next-3.16' of git://people.freedesktop.org/~agd5f/linux: (29 commits)
drm/edid: Add quirk for Sony PVM-2541A to get 12 bpc hdmi deep color.
drm/edid: Parse and handle HDMI deep color modes.
drm/radeon: Limit hdmi deep color bit depth to 12 bpc.
drm/radeon: Setup HDMI_CONTROL for hdmi deep color gcp's (v2)
drm/radeon: fix pll setup for hdmi deep color (v7)
drm/radeon: use hw cts/n values for deep color
drm/radeon: only apply hdmi bpc pll flags when encoder mode is hdmi
drm/radeon/atom: fix dithering on certain panels
drm/radeon: optimize CIK VM handling v2
drm/radeon: optimize SI VM handling
drm/radeon: add define for flags used in R600+ GTT
drm/radeon: rework page flip handling v3
drm/radeon: separate vblank and pflip crtc handling
drm/radeon: split page flip and pending callback
drm/radeon: remove drm_vblank_get|put from pflip handling
drm/radeon: remove (pre|post)_page_flip callbacks
drm/radeon/dp: fix lane/clock setup for dp 1.2 capable devices
drm/radeon: fix typo in radeon_connector_is_dp12_capable()
radeon: Remove useless quirk for zx1/FireGL X1 combo introduced with fdo #7770
vgaswitcheroo: switch the mux to the igp on power down when runpm is enabled
...
If a raid5/6 reshape is restarted (After stopping and re-assembling
the array) and the array is marked read-only (or read-auto), then
the reshape will appear to complete immediately, without actually
moving anything around. This can result in corruption.
There are two patches which do much the same thing in different places.
They are separate because one is an older bug and so can be applied to
more -stable kernels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=cTEe
-----END PGP SIGNATURE-----
Merge tag 'md/3.15-fixes' of git://neil.brown.name/md
Pull two md bugfixes from Neil Brown:
"Two md bugfixes for possible corruption when restarting reshape
If a raid5/6 reshape is restarted (After stopping and re-assembling
the array) and the array is marked read-only (or read-auto), then the
reshape will appear to complete immediately, without actually moving
anything around. This can result in corruption.
There are two patches which do much the same thing in different
places. They are separate because one is an older bug and so can be
applied to more -stable kernels"
* tag 'md/3.15-fixes' of git://neil.brown.name/md:
md: always set MD_RECOVERY_INTR when interrupting a reshape thread.
md: always set MD_RECOVERY_INTR when aborting a reshape or other "resync".
The ec_bhf driver is specific to the Beckhoff CX embedded PC series.
These are based on Intel x86 CPU. So we can add a dependency on
X86, with COMPILE_TEST as an alternative to still allow for broader
build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Darek Marcinkiewicz <reksio@newterm.pl>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Queued trim only works for some users with MU05 firmware. Revert to
blacklisting all firmware versions.
Introduced by commit d121f7d0cb ("libata: Update queued trim blacklist
for M5x0 drives") which this effectively reverts, while retaining the
blacklisting of M550.
See
https://bugzilla.kernel.org/show_bug.cgi?id=71371
for reports of trouble with MU05 firmware.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 fix from Peter Anvin:
"A single quite small patch that managed to get overlooked earlier, to
prevent a user space triggerable oops on systems without HPET"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, vdso: Fix an OOPS accessing the HPET mapping w/o an HPET
Here are some fixes for 3.15-rc8 that resolve a number of tiny USB
issues that have been reported, and there are some new device ids as
well.
All have been tested in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlOM9RkACgkQMUfUDdst+ykhbACeKn9kmESO0QMC2ST0kQkQxHJX
olYAoKbYZxvlZbdSJBmtYDbm1c5wrCfO
=H5ae
-----END PGP SIGNATURE-----
Merge tag 'usb-3.15-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some fixes for 3.15-rc8 that resolve a number of tiny USB
issues that have been reported, and there are some new device ids as
well.
All have been tested in linux-next"
* tag 'usb-3.15-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: delete endpoints from bandwidth list before freeing whole device
usb: pci-quirks: Prevent Sony VAIO t-series from switching usb ports
USB: cdc-wdm: properly include types.h
usb: cdc-wdm: export cdc-wdm uapi header
USB: serial: option: add support for Novatel E371 PCIe card
USB: ftdi_sio: add NovaTech OrionLXm product ID
USB: io_ti: fix firmware download on big-endian machines (part 2)
USB: Avoid runtime suspend loops for HCDs that can't handle suspend/resume
Here are some staging driver fixes for 3.15. 3 are for the speakup
drivers (one fix a regression caused in 3.15-rc, and the other 2 resolve
a tty issue found by Ben Hutchings) The comedi and r8192e_pci driver
fixes also resolve reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlOM9eUACgkQMUfUDdst+ykETACbBTSOZVE1pAIKGjGY2bcOtQET
yKMAnil04hAbmz5L/5TNvdkUWu+7SfGi
=K8cr
-----END PGP SIGNATURE-----
Merge tag 'staging-3.15-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some staging driver fixes for 3.15.
Three are for the speakup drivers (one fixes a regression caused in
3.15-rc, and the other two resolve a tty issue found by Ben Hutchings)
The comedi and r8192e_pci driver fixes also resolve reported issues"
* tag 'staging-3.15-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8192e_pci: fix htons error
Staging: speakup: Update __speakup_paste_selection() tty (ab)usage to match vt
Staging: speakup: Move pasting into a work item
staging: comedi: ni_daq_700: add mux settling delay
speakup: fix incorrect perms on speakup_acntsa.c
This bug is discovered by an recent F-RTO issue on tcpm list
https://www.ietf.org/mail-archive/web/tcpm/current/msg08794.html
The bug is that currently F-RTO does not use DSACK to undo cwnd in
certain cases: upon receiving an ACK after the RTO retransmission in
F-RTO, and the ACK has DSACK indicating the retransmission is spurious,
the sender only calls tcp_try_undo_loss() if some never retransmisted
data is sacked (FLAG_ORIG_DATA_SACKED).
The correct behavior is to unconditionally call tcp_try_undo_loss so
the DSACK information is used properly to undo the cwnd reduction.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was possible to get a setuid root or setcap executable to write to
it's stdout or stderr (which has been set made a netlink socket) and
inadvertently reconfigure the networking stack.
To prevent this we check that both the creator of the socket and
the currentl applications has permission to reconfigure the network
stack.
Unfortunately this breaks Zebra which always uses sendto/sendmsg
and creates it's socket without any privileges.
To keep Zebra working don't bother checking if the creator of the
socket has privilege when a destination address is specified. Instead
rely exclusively on the privileges of the sender of the socket.
Note from Andy: This is exactly Eric's code except for some comment
clarifications and formatting fixes. Neither I nor, I think, anyone
else is thrilled with this approach, but I'm hesitant to wait on a
better fix since 3.15 is almost here.
Note to stable maintainers: This is a mess. An earlier series of
patches in 3.15 fix a rather serious security issue (CVE-2014-0181),
but they did so in a way that breaks Zebra. The offending series
includes:
commit aa4cf9452f
Author: Eric W. Biederman <ebiederm@xmission.com>
Date: Wed Apr 23 14:28:03 2014 -0700
net: Add variants of capable for use on netlink messages
If a given kernel version is missing that series of fixes, it's
probably worth backporting it and this patch. if that series is
present, then this fix is critical if you care about Zebra.
Cc: stable@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each iPad model has a different product id, this patch adds support for iPad 2
(pid 0x12a2) and iPad 3 (pid 0x12a6). Note that iPad 2 must be jailbroken and a
third-party app must be used for tethering to work. On iPad 3, tethering works
out of the box (assuming your ISP is nice).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Sony PVM-2541A OLED high precision color display supports
both 10 bpc and 12 bpc hdmi deep color input, but its edid
does not signal any deep color support.
Add a quirk to force it being treated as a 12 bpc panel.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check the HDMI cea block for deep color mode bits. If available,
assign the highest supported bpc for a hdmi display, corresponding
to the given deep color modes.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCE-4/5/6 can't support more than 12 bpc deep color over hdmi,
so clamp to 12 bpc when a hdmi deep color capable display is
connected. This even makes sense on DCE-8+, which could do up
to 16 bpc, as driving with more than 12 bpc would only waste
video bandwidth as long as we don't support framebuffers with
more than 12 bpc depth.
On pre-DCE4 we clamp hdmi bit depth to 8 bpc, as those asics
don't support hdmi deep color.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Program HDMI_CONTROL to send general control packets
for hdmi deep color mode signalling at every video
frame if bpc > 8.
This is only supported on evergreen / DCE-4 and later.
v2: rebase
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to adjust the pll up for deep color modes.
Additionally, the atom bpc defines were wrong in certain
cases.
v2: set the adjusted clock to the pll clock for hdmi deep
color. This fixes display and audio issues with deep color
as reported by Andy Furniss <adf.lists@gmail.com>
v3: set crtc_clock as well
v4: setcrtcinfo on the adjusted mode
v5: just use the adjusted clock for setting the pll
v6: only use the adjusted clock for hdmi
v7: only DCE5 and DCE6 and bpc > 8
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Now it is not possible to set mtu to team device which has a port
enslaved to it. The reason is that when team_change_mtu() calls
dev_set_mtu() for port device, notificator for NETDEV_PRECHANGEMTU
event is called and team_device_event() returns NOTIFY_BAD forbidding
the change. So fix this by returning NOTIFY_DONE here in case team is
changing mtu in team_change_mtu().
Introduced-by: 3d249d4c "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Vetter