clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the commit "gpio: mvebu: switch to regmap for register access" the
driver use the regmap. Explicitly select the REGMAP_MMIO symbol to fix
build error.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Broadcom Vulcan (ARCH_VULCAN) has been discontinued and will be deleted
soon. So, update the GPIO_XLP Kconfig entry to remove the ARCH_VULCAN
dependency.
Also update the documentation to note that Cavium ThunderX2 uses this
driver.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mvebu gpio driver can also be used on arm64 mvebu SoC such as the
Armada 7K/8K. This commit allows to build the driver for them (when only
ARCH_MVEBU is defined)
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to be able to use this driver with the Armada 7K/8K SoCs, we
need to use the regmap to access the registers. Indeed for these new SoCs,
the gpio node will be part of a syscon.
[gregory.clement@free-electrons.com:
- fixed merge conflcit from 4.10 to 4.12-rc1
- added a commit log]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Crystal Cove PMIC has 16 real GPIOs but the ACPI code for devices
with this PMIC may address up to 95 GPIOs, these extra GPIOs are
called virtual GPIOs and are used by the ACPI code as a method of
accessing various non GPIO bits of PMIC.
Commit dcdc3018d6 ("gpio: crystalcove: support virtual GPIO") added
dummy support for these to avoid a bunch of ACPI errors, but instead of
ignoring writes / reads to them by doing:
if (gpio >= CRYSTALCOVE_GPIO_NUM)
return 0;
It accidentally introduced the following wrong check:
if (gpio > CRYSTALCOVE_VGPIO_NUM)
return 0;
Which means that attempts by the ACPI code to access these gpios
causes some arbitrary gpio to get touched through for example
GPIO1P0CTLO + gpionr % 8.
Since we do support input/output (but not interrupts) on the 0x5e
virtual GPIO, this commit makes to_reg return -ENOTSUPP for unsupported
virtual GPIOs so as to not have to check for (gpio >= CRYSTALCOVE_GPIO_NUM
&& gpio != 0x5e) everywhere and to make it easier to add support for more
virtual GPIOs in the future.
It then adds a check for to_reg returning an error to all callers where
this may happen fixing the ACPI code accessing virtual GPIOs accidentally
causing changes to real GPIOs.
Fixes: dcdc3018d6 ("gpio: crystalcove: support virtual GPIO")
Cc: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the mcp23s08 driver from gpio to pinctrl. Actual
pinctrl support for configuration of the pull-up resistors
follows in its own patch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver support basic XRA1403 functionalities:
- set gpio direction
- get gpio direction
- set gpio high/low
- get gpio status
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Semi Malinen <semi.malinen@ge.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver handles the GPIOs of all the Ingenic JZ47xx SoCs
currently supported by the upsteam Linux kernel.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For hot-pluggable devices adding GPIOs dynamically we need to
assemble and add the gpio lookup tables at probe time in modules,
so that requesting these GPIOs in attached drivers can work.
Export lookup table functions for modules.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We warn the user at driver probe time that debouncing is disabled.
However, if they request debouncing later on we print a confusing error
message:
gpio_aspeed 1e780000.gpio: Failed to convert 5000us to cycles at 0Hz: -524
Instead bail out when the clock is not present.
Fixes: 5ae4cb94b3 (gpio: aspeed: Add debounce support)
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----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=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
Here is the big set of new char/misc driver drivers and features for
4.12-rc1.
There's lots of new drivers added this time around, new firmware drivers
from Google, more auxdisplay drivers, extcon drivers, fpga drivers, and
a bunch of other driver updates. Nothing major, except if you happen to
have the hardware for these drivers, and then you will be happy :)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWQvAgg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yknsACgzkAeyz16Z97J3UTaeejbR7nKUCAAoKY4WEHY
8O9f9pr9gj8GMBwxeZQa
=OIfB
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of new char/misc driver drivers and features for
4.12-rc1.
There's lots of new drivers added this time around, new firmware
drivers from Google, more auxdisplay drivers, extcon drivers, fpga
drivers, and a bunch of other driver updates. Nothing major, except if
you happen to have the hardware for these drivers, and then you will
be happy :)
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (136 commits)
firmware: google memconsole: Fix return value check in platform_memconsole_init()
firmware: Google VPD: Fix return value check in vpd_platform_init()
goldfish_pipe: fix build warning about using too much stack.
goldfish_pipe: An implementation of more parallel pipe
fpga fr br: update supported version numbers
fpga: region: release FPGA region reference in error path
fpga altera-hps2fpga: disable/unprepare clock on error in alt_fpga_bridge_probe()
mei: drop the TODO from samples
firmware: Google VPD sysfs driver
firmware: Google VPD: import lib_vpd source files
misc: lkdtm: Add volatile to intentional NULL pointer reference
eeprom: idt_89hpesx: Add OF device ID table
misc: ds1682: Add OF device ID table
misc: tsl2550: Add OF device ID table
w1: Remove unneeded use of assert() and remove w1_log.h
w1: Use kernel common min() implementation
uio_mf624: Align memory regions to page size and set correct offsets
uio_mf624: Refactor memory info initialization
uio: Allow handling of non page-aligned memory regions
hangcheck-timer: Fix typo in comment
...
Core changes
- Return NULL from gpiod_get_optional() when GPIOLIB is disabled.
This was a much discussed change. It affects use cases where people
write drivers that might or might not be using GPIO resources.
I have decided that this is the lesser evil right now.
- Make gpiod_count() behave consistently across different hardware
descriptions.
- Fix the syntax around open drain/open source to not infer active
high/low semantics.
New drivers
- A new single-register fixed-direction framework driver for hardware
that have lines controlled by a single register that just work in
one direction (out or in), including IRQ support.
- Support the Fintek F71889A GPIO SuperIO controller.
- Support the National NI 169445 MMIO GPIO.
- Support for the X-Gene derivative of the DWC GPIO controller
- Support for the Rohm BD9571MWV-M PMIC GPIO controller.
- Refactor the Gemini GPIO driver to a generic Faraday FTGPIO driver
and replace both the Gemini and the Moxa ART custom drivers with
this driver.
Driver improvements
- A whole slew of drivers have their spinlocks chaned to raw spinlocks
as they provide irqchips, and thus we are progressing on realtime
compliance.
- Use devm_irq_alloc_descs() in a slew of drivers, getting managed
resources.
- Support for the embedded PWM controller inside the MVEBU driver.
- Debounce, open source and open drain support for the Aspeed driver.
- Misc smaller fixes like spelling and syntax and whatnot.
-----BEGIN PGP SIGNATURE-----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=DGPb
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.12 kernel cycle.
Core changes:
- Return NULL from gpiod_get_optional() when GPIOLIB is disabled.
This was a much discussed change. It affects use cases where people
write drivers that might or might not be using GPIO resources. I
have decided that this is the lesser evil right now.
- Make gpiod_count() behave consistently across different hardware
descriptions.
- Fix the syntax around open drain/open source to not infer active
high/low semantics.
New drivers:
- A new single-register fixed-direction framework driver for hardware
that have lines controlled by a single register that just work in
one direction (out or in), including IRQ support.
- Support the Fintek F71889A GPIO SuperIO controller.
- Support the National NI 169445 MMIO GPIO.
- Support for the X-Gene derivative of the DWC GPIO controller
- Support for the Rohm BD9571MWV-M PMIC GPIO controller.
- Refactor the Gemini GPIO driver to a generic Faraday FTGPIO driver
and replace both the Gemini and the Moxa ART custom drivers with
this driver.
Driver improvements:
- A whole slew of drivers have their spinlocks chaned to raw
spinlocks as they provide irqchips, and thus we are progressing on
realtime compliance.
- Use devm_irq_alloc_descs() in a slew of drivers, getting managed
resources.
- Support for the embedded PWM controller inside the MVEBU driver.
- Debounce, open source and open drain support for the Aspeed driver.
- Misc smaller fixes like spelling and syntax and whatnot"
* tag 'gpio-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: f7188x: Add a missing break
gpio: omap: return error if requested debounce time is not possible
gpio: Add ROHM BD9571MWV-M PMIC GPIO driver
gpio: gpio-wcove: fix GPIO IRQ status mask
gpio: DT bindings, move tca9554 from pcf857x to pca953x
gpio: move tca9554 from pcf857x to pca953x
gpio: arizona: Correct check whether the pin is an input
gpio: Add XRA1403 DTS binding documentation
dt-bindings: add exar to vendor prefixes list
gpio: gpio-wcove: fix irq pending status bit width
gpio: dwapb: use dwapb_read instead of readl_relaxed
gpio: aspeed: Add open-source and open-drain support
gpio: aspeed: Add debounce support
gpio: aspeed: dt: Add optional clocks property
gpio: aspeed: dt: Fix description alignment in bindings document
gpio: mvebu: Add limited PWM support
gpio: Use unsigned int for interrupt numbers
gpio: f7188x: Add F71889A GPIO support.
gpio: core: Decouple open drain/source flag with active low/high
gpio: arizona: Correct handling for reading input GPIOs
...
omap_gpio_debounce() does not validate that the requested debounce
is within a range it can handle. Instead it lets the register value
wrap silently, and always returns success.
This can lead to all sorts of unexpected behavior, such as gpio_keys
asking for a too-long debounce, but getting a very short debounce in
practice.
Fix this by returning -EINVAL if the requested value does not fit into
the register field. If there is no debounce clock available at all,
return -ENOTSUPP.
Fixes: e85ec6c304 ("gpio: omap: fix omap2_set_gpio_debounce")
Cc: <stable@vger.kernel.org> # 4.3+
Signed-off-by: David Rivshin <drivshin@allworx.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add driver for the GPIO block in the ROHM BD9571MWV-W MFD PMIC.
This block is pretty trivial and supports setting GPIO direction
as Input/Output and in case of Output, supports setting value.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to Whiskey Cove PMIC spec, bit 7 of GPIOIRQ0_REG belongs to
battery IO. So we should skip this bit when checking for GPIO IRQ pending
status. Otherwise, wcove_gpio_irq_handler() might go into the infinite
loop until IRQ "pending" status becomes 0. This patch fixes this issue.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Crystal Cove and Whiskey Cove are two different PMICs which are
installed on Intel Atom SoC based platforms.
Moreover there are two independent drivers that by some reason were
supposed (*) to get into one kernel module.
Fix the mess by clarifying Kconfig option for Crystal Cove and split
Whiskey Cove out of it.
(*) It looks like the configuration was never tested with
INTEL_SOC_PMIC=n. The line in Makefile is actually wrong.
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> (supporter:ACPI)
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The TCA9554 doesn't work with the pcf857x driver, trying to change the direction
gives a NAK bailout error.
TCA9554 is similar to the PCA9554, thus change the driver.
Signed-off-by: Anders Darander <anders@chargestorm.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The logic to check if the pin is an input or output whilst testing if we
need to read the register value from the hardware or not is currently
inverted. Remove the erroneous not from the if statement.
Fixes: 11598d1740 ("gpio: arizona: Correct handling for reading input GPIOs")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Whiskey cove PMIC has three GPIO banks with total number of 13 GPIO
pins. But when checking for the pending status, for_each_set_bit() uses
bit width of 7 and hence it only checks the status for first 7 GPIO pins
missing to check/clear the status of rest of the GPIO pins. This patch
fixes this issue.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 67809b974a ("GPIO: gpio-dwapb: Change readl&writel to
dwapb_read&dwapb_write") missed this readl_relaxed() usage, I'm not
sure the reason, maybe for performance reason? But if we do care
the performance, we could use the relaxed io in dwapb_read and
dwapb_write.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As per the datasheet, manage the IO and value states to implement
open-source/open-drain, but do this by falling back to gpiolib's
emulation.
This commit simply makes the behaviour explicit for clarity, rather than
relying on the implicit return of -ENOTSUPP to trigger the emulation.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Each GPIO in the Aspeed GPIO controller can choose one of four input
debounce states: to disable debouncing for an input, or select from one
of three programmable debounce timer values. Each GPIO in a
four-bank-set is assigned one bit in each of two debounce configuration
registers dedicated to the set, and selects a debounce state by
configuring the two bits to select one of the four options.
The limitation on debounce timer values is managed by mapping offsets
onto a configured timer value and keeping count of the number of users
a timer has. Timer values are configured on a first-come-first-served
basis.
A small twist in the hardware design is that the debounce configuration
register numbering is reversed with respect to the binary representation
of the debounce timer of interest (i.e. debounce register 1 represents
bit 1, and debounce register 2 represents bit 0 of the timer numbering).
Tested on an AST2500EVB with additional inspection under QEMU's
romulus-bmc machine.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Armada 370/XP devices can 'blink' GPIO lines with a configurable on
and off period. This can be modelled as a PWM.
However, there are only two sets of PWM configuration registers for
all the GPIO lines. This driver simply allows a single GPIO line per
GPIO chip of 32 lines to be used as a PWM. Attempts to use more return
EBUSY.
Due to the interleaving of registers it is not simple to separate the
PWM driver from the GPIO driver. Thus the GPIO driver has been
extended with a PWM driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
URL: https://patchwork.ozlabs.org/patch/427287/
URL: https://patchwork.ozlabs.org/patch/427295/
[Ralph Sennhauser:
* Port forward
* Merge PWM portion into gpio-mvebu.c
* Switch to atomic PWM API
* Add new compatible string marvell,armada-370-xp-gpio
* Update and merge documentation patch
* Update MAINTAINERS]
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/gpio/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
cc: Alexandre Courbot <gnurou@gmail.com>
cc: linux-gpio@vger.kernel.org
Interrupt numbers are never negative, zero serves as the special invalid
value.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add F71889A GPIO support.
Fintek F71889A is a SuperIO. It contains HWMON/GPIO/Serial Ports.
Datasheet:
http://www.alldatasheet.com/datasheet-pdf/pdf/459076/FINTEK/F71889A.html
Its virtually identical to the F71889F superio as far as gpios go.
One oddity is GPIO2 at index 0xD0; the datasheet only lists gpio's 7-5,
but it logically seems that it should continue down to 0. I'm not sure
if the driver can handle gpios that are shifted away from index 0 as it
currently stands.
Signed-off-by: Marty Plummer <netz.kernel@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, the GPIO interface is said to Open Drain if it is Single
Ended and active LOW. Similarly, it is said as Open Source if it is
Single Ended and active HIGH.
The active HIGH/LOW is used in the interface for setting the pin
state to HIGH or LOW when enabling/disabling the interface.
In Open Drain interface, pin is set to HIGH by putting pin in
high impedance and LOW by driving to the LOW.
In Open Source interface, pin is set to HIGH by driving pin to
HIGH and set to LOW by putting pin in high impedance.
With above, the Open Drain/Source is unrelated to the active LOW/HIGH
in interface. There is interface where the enable/disable of interface
is ether active LOW or HIGH but it is Open Drain type.
Hence decouple the Open Drain with Single Ended + Active LOW and
Open Source with Single Ended + Active HIGH.
Adding different flag for the Open Drain/Open Source which is valid
only when Single ended flag is enabled.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO register is cached since all the configuration resides within
it, however, this means for input GPIOs the driver will not return the
actual state but the last value written to the register cache.
To correct this in the case of reading an input GPIO resume the CODEC
and drop the cache for the input register to ensure an actual hardware
read takes place.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If, while locating GPIOs by name, we get probe deferral, we should
immediately report it to caller rather than trying to fall back to parsing
unnamed GPIOs from _CRS block.
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-and-Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On Bay Trail / Cherry Trail systems with a LID switch, the LID switch is
often connect to a gpioint handled by an _IAE event handler.
Before this commit such systems would not wake up when opening the lid,
requiring the powerbutton to be pressed after opening the lid to wakeup.
Note that Bay Trail / Cherry Trail systems use suspend-to-idle, so
the interrupts are generated anyway on those lines on lid switch changes,
but they are treated by the IRQ subsystem as spurious while suspended if
not marked as wakeup IRQs.
This commit calls enable_irq_wake() for _IAE GpioInts with a valid
event handler which have their Wake flag set. This fixes such systems
not waking up when opening the lid.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 104-idi-48 gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pci-idio-16 gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 104-idio-16 gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for mapping gpio-reg gpios to interrupts. This may be a
non-linear mapping - some gpios in the register may not even have
corresponding interrupts associated with them, so we need to pass an
array.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a simple, generic, single register fixed-direction GPIO driver.
This is able to support a single register with a mixture of inputs
and outputs.
This is different from gpio-mmio and gpio-74xx-mmio:
* gpio-mmio doesn't allow a fixed direction, it assumes there is always
a direction register.
* gpio-74xx-mmio only supports all-in or all-out setups
* gpio-74xx-mmio is DT only, this needs to support legacy too
* they don't double-read when getting the GPIO value, as required by
some implementations that this driver supports
* we need to always do 32-bit reads, which bgpio doesn't guarantee
* the current output state may not be readable from the hardware
register - reading may reflect input status but not output status.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow gpiolib to read back the current IO direction configuration by
implementing the .get_direction callback. This, in part, allows
debugfs to report the complete true hardware state rather than the
software state.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use IO accessors to access the SA1100 registers rather than accessing
them directly.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use sa11x0_gpio_set_wake() to set the PWER register, as provided by
Dmitry some time back.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mentioned flags are dedicated solely for consumer API.
Replace them by explicit values.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[Made a !bang clamp to (0,1) instead of infix ? operator]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now the wm831x-core has basic DT support we can update this driver to
allow use of the GPIOs within a device tree system.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
GPIO ACPI library is going to be stricter about resources, thus, expand
comment regarding "reset" GPIO resource in this driver to clarify its
usage in ACPI case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For sake of better maintenance sort the headers by alphabetical order.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce ->get_direction() callback for the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[Removed use of GPIOF_DIR* flags]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the BIT macro instead of explicitly shifting bits for some added
clarity.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO-based NAND controller on National Instruments 169445 hardware
exposes a set of simple lines for the control signals.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This just deletes the Moxa ART driver and replaces it with the
more versatile Faraday FTGPIO010 driver.
Make this default on for ARCH_GEMINI and ARCH_MOXART so we do
not get Kconfig glitches.
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Gemini driver is actually a driver for the Faraday Technology
FTGPIO010 IP block. We rename the driver and the Kconfig symbol and
put in a a new compatible string for the Moxa ART SoC that is also
using this IP block.
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace the open coded registration of the cdev and dev with the
new device_add_cdev() helper. The helper replaces a common pattern by
taking the proper reference against the parent device and adding both
the cdev and the device.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an interrupt occurs on an MCP23S08 chip, the INTF register will only
contain one bit as causing the interrupt. If more than two pins change at
the same time on the chip, this causes one of the pins to not be reported.
This patch fixes the logic for checking if a pin has changed, so that
multiple pins will always cause more than one change.
Cc: stable@vger.kernel.org
Signed-off-by: Robert Middleton <robert.middleton@rm5248.com>
Tested-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A modern compiler should know better when to inline, so drop the inline
keywords.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use unsigned int instead of plain unsigned as reported by checkpatch.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While this isn't an issue according to checkpatch two styles are used.
Add a blank line to the block comments missing a blank line at the start
so multiline block comments look the same across the file.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When acpi_dev_gpio_irq_get gets called with an index of say 2, it should
not care if acpi_get_gpiod for index 0 or 1 returns -EPROBE_DEFER.
This allows drivers which request a gpioint with index > 0 to function
if there is no gpiochip driver (loaded) for gpioints with a lower index.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's unusual to have error checking like (ret <= 0) in cases when
counting GPIO resources. In case when it's mandatory we propagate the
error (-ENOENT), otherwise we don't use the result.
This makes consistent behaviour across all possible variants called in
gpiod_count().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's unusual to have error checking like (ret <= 0) in cases when
counting GPIO resources. In case when it's mandatory we propagate the
error (-ENOENT), otherwise we don't use the result.
This makes consistent behaviour across all possible variants called in
gpiod_count().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ARCH_VULCAN arm64 platform (for Broadcom Vulcan ARM64 processors) has
been discontinued. Cavium's ThunderX2 CN99XX (ARCH_THUNDER2) will be
the next revision of this platform.
Update compile dependencies and ACPI ID to reflect this change.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
[Drop depreciation of ARCH_VULCAN]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The zx gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ws16c48 gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pl061 gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The etraxfs gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ath79 gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: Aban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The bcm-kona gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 104-dio-48e gpio driver currently implements an irq_chip for
handling interrupts; due to how irq_chip handling is done, it's
necessary for the irq_chip methods to be invoked from hardirq context,
even on a a real-time kernel. Because the spinlock_t type becomes a
"sleeping" spinlock w/ RT kernels, it is not suitable to be used with
irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The altera gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a real-time
kernel. Because the spinlock_t type becomes a "sleeping" spinlock w/ RT
kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PC/104 drivers should be hidden on machines which do not support PC/104
devices. This patch adds the PC104 Kconfig option as a dependency for
the relevant PC/104 device driver Kconfig options.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use device resource managed variants of irq_alloc_descs() and
request_irq() and remove the code manually freeing irq resources.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver never frees the interrupt descriptors it allocates. Fix
it by using the resource managed version of irq_alloc_descs().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver never frees the interrupt descriptors it allocates. Fix
it by using the resource managed version of irq_alloc_descs().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use device resource managed variants of irq_alloc_descs() and
request_irq() and remove the code manually freeing irq resources.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver never frees the interrupt descriptors it allocates. Fix
it by using the resource managed version of irq_alloc_descs().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver never frees the interrupt descriptors it allocates. Fix
it by using the resource managed version of irq_alloc_descs().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the resource managed variant of irq_alloc_descs() and remove the
code manually freeing allocated interrupt descriptors.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use device resource managed variants of irq_alloc_descs() and
request_irq() and remove the code manually freeing irq resources.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use device resource managed variants of irq_alloc_descs() and
request_irq() and remove the code manually freeing irq resources.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver never frees the allocated interrupt descriptors. Fix it by
using a resource managed variant of irq_alloc_descs().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver never frees the irq descriptors it allocates. Fix it by
using a resource managed variant of irq_alloc_descs().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the resource managed variant of irq_alloc_descs(). This allows us
to remove gpio_mockup_remove().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current code does not set output level in exar_direction_output, fix it.
Also move the direction_output/direction_input code block to avoid forward
declaration for exar_set_value().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce device managed variant of acpi_dev_add_driver_gpios() and its
counterpart acpi_dev_remove_driver_gpios().
The functions in most cases are used in driver's ->probe() and
->remove() callbacks, that's why it's useful to have managed variant of
them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove extra 'l' in "successfull".
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When a threaded irq handler is chained attached to one of the gpio
pins when configure for level irq the altera_gpio_irq_leveL_high_handler
does not mask the interrupt while being handled by the chained irq.
This resulting in the threaded irq not getting enough cycles to complete
quickly enough before the irq was disabled as faulty. handle_level_irq
should be used in this situation instead of handle_simple_irq.
In gpiochip_irqchip_add set default handler to handle_bad_irq as
per Documentation/gpio/driver.txt. Then set the correct handler in
the set_type callback.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When CONFIG_PM_SLEEP is disabled, we get a warning about unused functions:
drivers/gpio/gpio-xgene.c:155:12: warning: 'xgene_gpio_resume' defined but not used [-Wunused-function]
static int xgene_gpio_resume(struct device *dev)
^~~~~~~~~~~~~~~~~
drivers/gpio/gpio-xgene.c:142:12: warning: 'xgene_gpio_suspend' defined but not used [-Wunused-function]
static int xgene_gpio_suspend(struct device *dev)
The warnings are harmless and can be avoided by simplifying the code and marking
the functions as __maybe_unused.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
copy_from_user() returns the number of bytes remaining to be copied but
we want to return negative error codes on failue.
Fixes: 9202ba2397 ("gpio: mockup: implement event injecting over debugfs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set the gpio_chip parent property since some recent functions
such as devprop_gpiochip_set_names() can use it.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Next generation of X-Gene SoC's GPIO hardware register map is very
similar to DW GPIO. It only differs by a few register addresses.
This patch modifies DW GPIO driver to accommodate the difference
in a few register addresses.
Signed-off-by: Hoan Tran <hotran@apm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Augment fwnode_get_named_gpiod() to configure the GPIO pin
immediately after requesting it like all other APIs do.
This is a treewide change also updating all users.
- Pass a GPIO label down to gpiod_request() from
fwnode_get_named_gpiod(). This makes debugfs and the userspace
ABI correctly reflect the current in-kernel consumer of a pin
taken using this abstraction. This is a treewide change also
updating all users.
- Rename devm_get_gpiod_from_child() to
devm_fwnode_get_gpiod_from_child() to reflect the fact that this
function is operating on a fwnode object. This is a treewide
change also updating all users.
- Make it possible to take multiple GPIOs in a single hog of device
tree hogs.
- The refactorings switching GPIO chips to use the .set_config()
callback using standard pin control properties and providing
a backend into the pin control subsystem that were also merged
into the pin control tree naturally appear here too.
Testing instrumentation:
- A whole slew of cleanups and improvements to the mockup GPIO
driver. We now have an extended userspace test exercising the
subsystem, and we can inject interrupts etc from userspace
to fully test the core GPIO functionality.
New drivers:
- New driver for the Cortina Systems Gemini GPIO controller.
- New driver for the Exar XR17V352/354/358 chips.
- New driver for the ACCES PCI-IDIO-16 PCI GPIO card.
Driver changes:
- RCAR: set the irqchip parent device, add fine-grained runtime
PM support.
- pca953x: support optional RESET control line on the chip.
- DaVinci: cleanups and simplifications. Add support for multiple
instances.
- .set_multiple() and naming of lines on more or less all of the
ISA/PCI GPIO controllers.
- mcp23s08: refactored to use regmap as a first step to further
rewrites and modernizations.
-----BEGIN PGP SIGNATURE-----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=O81I
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.11 cycle
Core changes:
- Augment fwnode_get_named_gpiod() to configure the GPIO pin
immediately after requesting it like all other APIs do. This is a
treewide change also updating all users.
- Pass a GPIO label down to gpiod_request() from
fwnode_get_named_gpiod(). This makes debugfs and the userspace ABI
correctly reflect the current in-kernel consumer of a pin taken
using this abstraction. This is a treewide change also updating all
users.
- Rename devm_get_gpiod_from_child() to
devm_fwnode_get_gpiod_from_child() to reflect the fact that this
function is operating on a fwnode object. This is a treewide change
also updating all users.
- Make it possible to take multiple GPIOs in a single hog of device
tree hogs.
- The refactorings switching GPIO chips to use the .set_config()
callback using standard pin control properties and providing a
backend into the pin control subsystem that were also merged into
the pin control tree naturally appear here too.
Testing instrumentation:
- A whole slew of cleanups and improvements to the mockup GPIO
driver. We now have an extended userspace test exercising the
subsystem, and we can inject interrupts etc from userspace to fully
test the core GPIO functionality.
New drivers:
- New driver for the Cortina Systems Gemini GPIO controller.
- New driver for the Exar XR17V352/354/358 chips.
- New driver for the ACCES PCI-IDIO-16 PCI GPIO card.
Driver changes:
- RCAR: set the irqchip parent device, add fine-grained runtime PM
support.
- pca953x: support optional RESET control line on the chip.
- DaVinci: cleanups and simplifications. Add support for multiple
instances.
- .set_multiple() and naming of lines on more or less all of the
ISA/PCI GPIO controllers.
- mcp23s08: refactored to use regmap as a first step to further
rewrites and modernizations"
* tag 'gpio-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (61 commits)
gpio: reintroduce devm_get_gpiod_from_child()
gpio: pci-idio-16: Fix PCI BAR index
gpio: pci-idio-16: Fix PCI device ID code
gpio: mockup: implement event injecting over debugfs
gpio: mockup: add a dummy irqchip
gpio: mockup: implement naming the lines
gpio: mockup: code shrink
gpio: mockup: readability tweaks
gpio: Add GPIO support for the ACCES PCI-IDIO-16
gpio: Add the devm_fwnode_get_index_gpiod_from_child() helper
gpio: Rename devm_get_gpiod_from_child()
gpio: mcp23s08: Select REGMAP/REGMAP_I2C to fix build error
gpio: ws16c48: Add support for GPIO names
gpio: gpio-mm: Add support for GPIO names
gpio: 104-idio-16: Add support for GPIO names
gpio: 104-idi-48: Add support for GPIO names
gpio: 104-dio-48e: Add support for GPIO names
gpio: ws16c48: Remove unnecessary driver_data set
gpio: gpio-mm: Remove unnecessary driver_data set
gpio: 104-idio-16: Remove unnecessary driver_data set
...
The PCI BAR0 and BAR1 for the PCI-IDIO-16 hold information for the PLX
9052 bridge chip on the device. The PCI BAR2 holds the necessary base
address for I/O control of the PCI-IDIO-16. This patch corrects the PCI
BAR index mismatch for the PCI-IDIO-16 GPIO driver.
Fixes: 02e74fc040 ("gpio: Add GPIO support for the ACCES PCI-IDIO-16")
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES PCI-IDIO-16 has a PCI device ID code of 0x0DC8. It is
incorrect to use the PCI device ID code of the ACCES PCI-IIRO-8
(0x0F00). This patch fixes the said PCI device ID code mismatch.
Fixes: 02e74fc040 ("gpio: Add GPIO support for the ACCES PCI-IDIO-16")
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Create a debugfs directory for every mockup chip and a single file
for every line. Writing (0 or 1) to these files allows the user to
inject line events (falling or rising edge respectively).
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setup a dummy irqchip that will allow us to inject line events for
testing purposes.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to allow testing line lookup by name from user space, add
a new boolean parameter that indicates whether we want the lines to
be named. The name is created by concatenating the chip name and the
line offset value.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Moving a couple of lines around allows us to shrink the code a bit
while keeping the same functionality.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The following patch tries to improve the readability of the mockup
driver.
The driver is called gpio-mockup, so add the same prefix to all
functions and structures.
Add some newlines and use a temporary pointer in gpio_mockup_add().
Drop the name of the direction enum and rename the enum values to
better reflect their purpose.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES PCI-IDIO-16 device provides 32 lines of digital I/O (16 lines
of optically-isolated digital inputs for AC and DC control signals, and
16 lines of solid state switch digital outputs). An interrupt is
generated when any of the inputs change state (low to high or high to
low). Input filter control is not supported by this driver, and input
filters are deactivated by this driver.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
1736f75d35 is a (v2) patch which had
unresolved review comments[1]. Address the comments by removing the use
of macros from the consumer header (this patch represents the diff
between v2 and v3[2]).
[1] https://lkml.org/lkml/2017/1/26/337
[2] https://lkml.org/lkml/2017/1/26/786
Fixes: 1736f75d35 ("gpio: aspeed: Add banks Y, Z, AA, AB and AC")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
devm_fwnode_get_gpiod_from_child() currently allows GPIO users to
request a GPIO that is defined in a child fwnode instead of directly in
the device fwnode.
Extend this API by adding the devm_fwnode_get_index_gpiod_from_child()
helper which does the same except you can also specify an index in case
the 'xx-gpios' property describe several GPIOs.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename devm_get_gpiod_from_child() into
devm_fwnode_get_gpiod_from_child() to reflect the fact that this
function is operating on a fwnode object.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver now using devm_regmap_init/devm_regmap_init_i2c, so it needs
to select REGMAP/REGMAP_I2C accordingly.
Fixes: ("3d84fdb3f0b5 gpio: mcp23s08: use regmap")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch sets the gpio_chip names option with an array of GPIO line
names that match the manual documentation for the WinSystems WS16C48.
This should make it easier for users to identify which GPIO line
corresponds to a respective GPIO pin on the device.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch sets the gpio_chip names option with an array of GPIO line
names that match the manual documentation for the Diamond Systems
GPIO-MM. This should make it easier for users to identify which GPIO
line corresponds to a respective GPIO pin on the device.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch sets the gpio_chip names option with an array of GPIO line
names that match the manual documentation for the ACCES 104-IDIO-16.
This should make it easier for users to identify which GPIO line
corresponds to a respective GPIO pin on the device.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch sets the gpio_chip names option with an array of GPIO line
names that match the manual documentation for the ACCES 104-IDI-48.
This should make it easier for users to identify which GPIO line
corresponds to a respective GPIO pin on the device.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch sets the gpio_chip names option with an array of GPIO line
names that match the manual documentation for the ACCES 104-DIO-48E.
This should make it easier for users to identify which GPIO line
corresponds to a respective GPIO pin on the device.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting driver_data was necessary to access private data in the
ws16c48_remove function. Now that the ws16c48_remove function is gone,
driver_data is no longer used. This patch removes the relevant code.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting driver_data was necessary to access private data in the
gpiomm_remove function. Now that the gpiomm_remove function is gone,
driver_data is no longer used. This patch removes the relevant code.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting driver_data was necessary to access private data in the
idio_16_remove function. Now that the idio_16_remove function is gone,
driver_data is no longer used. This patch removes the relevant code.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting driver_data was necessary to access private data in the
idi_48_remove function. Now that the idi_48_remove function is gone,
driver_data is no longer used. This patch removes the relevant code.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting driver_data was necessary to access private data in the
dio48e_remove function. Now that the dio48e_remove function is gone,
driver_data is no longer used. This patch removes the relevant code.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use regmap API to save some lines of codes and have
debugfs support for all of the MCP's registers.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the gpiochip_add_data call and
request_irq call with the devm_gpiochip_add_data call and
devm_request_irq call respectively. In addition, the ws16c48_remove
function has been removed as no longer necessary due to the use of the
relevant devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the gpiochip_add_data call with
the devm_gpiochip_add_data call. In addition, the gpiomm_remove function
has been removed as no longer necessary due to the use of the relevant
devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the gpiochip_add_data call and
request_irq call with the devm_gpiochip_add_data call and
devm_request_irq call respectively. In addition, the idio_16_remove
function has been removed as no longer necessary due to the use of the
relevant devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the gpiochip_add_data call and
request_irq call with the devm_gpiochip_add_data call and
devm_request_irq call respectively. In addition, the idi_48_remove
function has been removed as no longer necessary due to the use of the
relevant devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the gpiochip_add_data call and
request_irq call with the devm_gpiochip_add_data call and
devm_request_irq call respectively. In addition, the dio48e_remove
function has been removed as no longer necessary due to the use of the
relevant devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently we already have two pin configuration related callbacks
available for GPIO chips .set_single_ended() and .set_debounce(). In
future we expect to have even more, which does not scale well if we need
to add yet another callback to the GPIO chip structure for each possible
configuration parameter.
Better solution is to reuse what we already have available in the
generic pinconf.
To support this, we introduce a new .set_config() callback for GPIO
chips. The callback takes a single packed pin configuration value as
parameter. This can then be extended easily beyond what is currently
supported by just adding new types to the generic pinconf enum.
If the GPIO driver is backed up by a pinctrl driver the GPIO driver can
just assign gpiochip_generic_config() (introduced in this patch) to
.set_config and that will take care configuration requests are directed
to the pinctrl driver.
We then convert the existing drivers over .set_config() and finally
remove the .set_single_ended() and .set_debounce() callbacks.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is less straight-forward than one would hope, as some banks only
have 4 pins rather than 8, others are output only, yet more (W and
X, already supported) are input-only, and in the case of the g4 SoC bank
AC doesn't exist.
Add some structs to describe the varying properties of different banks
and integrate mechanisms to deny requests for unsupported
configurations.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Aspeed SoCs have more GPIOs than can be represented with A-Z. The
documentation uses two letter names such as AA and AB, so make the names
a three-character array in the bank struct to accommodate this.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Exar XR17V352/354/358 chips have 16 multi-purpose inputs/outputs which
can be controlled using gpio interface.
Add the gpio specific code.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The WinSystems WS16C48 provides registers where 8 lines of GPIO may be
set at a time. This patch add support for the set_multiple callback
function, thus allowing multiple GPIO output lines to be set more
efficiently in groups.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Diamond Systems GPIO-MM series provides registers where 8 lines of
GPIO may be set at a time. This patch add support for the set_multiple
callback function, thus allowing multiple GPIO output lines to be set
more efficiently in groups.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-IDIO-16 series provides registers where 8 lines of GPIO
may be set at a time. This patch add support for the set_multiple
callback function, thus allowing multiple GPIO output lines to be set
more efficiently in groups.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-DIO-48E series provides registers where 8 lines of GPIO
may be set at a time. This patch add support for the set_multiple
callback function, thus allowing multiple GPIO output lines to be set
more efficiently in groups.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a heavy edit/rewrite of the GPIO driver for the Gemini
SoC from arch/arm/mach-gemini/gpio.c.
This rewrite uses all the best-in-class helper like generic
GPIO and GPIOLIB_IRQCHIP and has been tested on ITian Square One
Gemini-based NAS/router.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With the current redesign of driver it's not necessary to have
custom .xlate() as the gpiolib will assign default of_gpio_simple_xlate().
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update GPIO driver to support Multiple GPIO controllers by updating
the base of subsequent GPIO chips with total of previous chips
gpio count so that gpio_add_chip gets unique numbers.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Davinci GPIO driver is implemented to work with one monolithic
Davinci GPIO platform device which may have up to Y(144) gpios.
The Davinci GPIO driver instantiates number of GPIO chips with
max 32 gpio pins per each during initialization and one IRQ domain.
So, the current GPIO's opjects structure is:
<platform device> Davinci GPIO controller
|- <gpio0_chip0> ------|
... |--- irq_domain (hwirq [0..143])
|- <gpio0_chipN> ------|
Current driver creates one chip for every 32 GPIOs in a controller.
This was a limitation earlier now there is no need for that. Hence
redesigning the driver to create one gpio chip for all the ngpio
in the controller.
|- <gpio0_chip0> ------|--- irq_domain (hwirq [0..143]).
The previous discussion on this can be found here:
https://www.spinics.net/lists/linux-omap/msg132869.html
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio2regs is written making an assumption that driver supports only
one instance of gpio controller. Removing this and adding a generic
array so as to support multiple instances of gpio controllers.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The only usage of function intel_gpio_runtime_idle() is here (in the
same file):
static const struct dev_pm_ops intel_gpio_pm_ops = {
SET_RUNTIME_PM_OPS(NULL, NULL, intel_gpio_runtime_idle)
};
And when CONFIG_PM is not set, the macro SET_RUNTIME_PM_OPS expands to
nothing, causing the following compiler warning:
drivers/gpio/gpio-intel-mid.c:324:12: warning: ‘intel_gpio_runtime_idle’
defined but not used [-Wunused-function]
static int intel_gpio_runtime_idle(struct device *dev)
Fix it by annotating the function with __maybe_unused.
Signed-off-by: Augusto Mecking Caringi <augustocaringi@gmail.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently all users of fwnode_get_named_gpiod() have no way to
specify a label for the GPIO. So GPIOs listed in debugfs are shown
with label "?". With this change a proper label is used.
Also adjust all users so they can pass a label, properly retrieved
from device tree properties.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make fwnode_get_named_gpiod() consistent with the rest of
gpiod_get() like API, i.e. configure GPIO pin immediately after
request.
Besides obvious clean up it will help to configure pins based
on firmware provided resources.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The helper function for adding a GPIO chip compiles in a lockdep
key for debugging, the same key is needed for nested chips as
well.
The macro construction is unreadable, replace this with two
static inlines instead.
The _gpiochip_irqchip_add prefixed function is not helpful,
rename it with gpiochip_irqchip_add_key() that tell us what the
function is actually doing.
Fixes: d245b3f9bd ("gpio: simplify adding threaded interrupts")
Cc: Roger Quadros <rogerq@ti.com>
Reported-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reported-by: Roger Quadros <rogerq@ti.com>
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Casting a pointer to an int is not portable, and provokes a compiler
warning. Cast to unsigned long instead to avoid the warning.
drivers/gpio/gpio-mvebu.c: In function 'mvebu_gpio_probe':
drivers/gpio/gpio-mvebu.c:662:17: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
soc_variant = (int) match->data;
^
This will be needed when building gpio-mvebu for Armada 7k/8k ARM64
SoCs.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add optional reset-gpios pin control. If present, de-assert the
specified reset gpio pin to bring the chip out of reset.
v2:
- Specify that reset signal to PCA953x chip is active low, in
binding doc.
- reorder includes in gpio-pca953x.c.
- remove dev_err() on devm_gpiod_get_optional() error return.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
container_of() does pointer math on the pointer that's passed in.
If it were to return a NULL pointer the value passed in would
need to be perfectly offset from 0 to make that so. Remove these
checks because they don't make sense.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It seems the code had been changed, but description left untouched.
Update description of the struct acpi_gpio_info and relative comments
accordingly.
Fixes: commit 52044723cd ("ACPI / gpio: Add irq_type when a GPIO is used as an interrupt")
Cc: Christophe RICARD <christophe.ricard@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The macro for_each_set_bit() effectively looks up to the next
set bit in array of bits.
Instead of open coding that switch to for_each_set_bit() in
gpio_chip_set_multiple().
While here, make gpio_chip_set_multiple() non-destructive
against its parameters. We are safe since all callers, i.e.
gpiod_set_array_value_complex(), handle that already.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
davinci_gpio_controller struct has set_data, in_data, clr_data
members that are assigned and never used.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have already a global array of possible GPIO suffixes. Use it here instead
of another copy of them.
Unfortunately this will not reduce the memory footprint, though allows to easy
maintain list in only one place.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When listing multiple GPIOs in the "gpios" property of a GPIO hog, only
the first GPIO is affected. The user is left clueless about the
dysfunctioning of the other GPIOs specified.
Fix this by adding and documenting support for specifying multiple
GPIOs in a single GPIO hog.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch updates my email address as I no longer have access to the old
one.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When removing a gpiochip that uses GPIO hogging (e.g. by unloading the
chip's DT overlay), a warning is printed:
gpio gpiochip8: REMOVING GPIOCHIP WITH GPIOS STILL REQUESTED
This happens because gpiochip_free_hogs() is called after the gdev->chip
pointer is reset to NULL. Hence __gpiod_free() cannot determine the
chip in use, and cannot clear flags nor call the optional chip-specific
.free() callback.
Move the call to gpiochip_free_hogs() up to fix this.
Cc: stable@vger.kernel.org
Fixes: ff2b135922 ("gpio: make the gpiochip a real device")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Building with an old toolchain, I ran into this warning:
WARNING: vmlinux.o(.text+0x63eef0): Section mismatch in reference
from the function mxs_gpio_probe() to the function
.init.text:mxs_gpio_init_gc()
Clearly the annotation is wrong, since the function is called from the
non-init probe, so let's remove it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the chip name buffer is allocated on the stack and the
address of the buffer is passed to the gpio framework. It's invalid
after probe() returns, so the sysfs label attribute displays garbage.
Use devm_kasprintf() for each string instead.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This variable is not used outside this module. Make it static.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently gpio modules are runtime-resumed at probe time. This means the
gpio module will be active all the time (except during system suspend,
if not configured as a wake-up source).
While an R-Car Gen2 gpio module retains pins configured for output at
the requested level while put in standby mode, gpio register cannot be
accessed while suspended. Unfortunately pm_runtime_get_sync() cannot be
called from all contexts where gpio register access is needed. Hence
move the Runtime PM handling from probe/remove time to gpio request/free
time, which is probably the best we can do.
On r8a7791/koelsch, gpio modules 0, 1, 3, and 4 are now suspended during
normal use (gpio2 is used for LEDs and regulators, gpio5 for keys, gpio6
for SD-Card CD & WP, gpio7 for keys and regulators).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[Niklas: s/gpio_to_priv(chip)/gpiochip_get_data(chip)/]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This enables Runtime PM handling for interrupts.
By setting the parent_device in struct irq_chip genirq will call the
pm_runtime_get/put APIs when an IRQ is requested/freed.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Simplify threaded interrupt handling: instead of passing
numbed parameters to gpiochip_irqchip_add_chained() we
create a new call: gpiochip_irqchip_add_nested() so the two
types are clearly semantically different. Also make sure
that all nested chips call gpiochip_set_nested_irqchip()
which is necessary for IRQ resend to work properly if
it happens.
- Return error on seek operations for the chardev.
- Clamp values set as part of gpio[d]_direction_output() so
that anything != 0 will be send down to the driver as "1"
not the value passed in.
- ACPI can now support naming of GPIO lines, hogs and holes
in the GPIO lists.
New drivers:
- The SX150x driver was deemed unfit for the GPIO subsystem
and was moved over to a combined GPIO+pinctrl driver in the
pinctrl subsystem.
New features:
- Various cleanups to various drivers.
-----BEGIN PGP SIGNATURE-----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=2UpT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Luinus Walleij:
"Bulk GPIO changes for the v4.10 kernel cycle:
Core changes:
- Simplify threaded interrupt handling: instead of passing numbed
parameters to gpiochip_irqchip_add_chained() we create a new call:
gpiochip_irqchip_add_nested() so the two types are clearly
semantically different. Also make sure that all nested chips call
gpiochip_set_nested_irqchip() which is necessary for IRQ resend to
work properly if it happens.
- Return error on seek operations for the chardev.
- Clamp values set as part of gpio[d]_direction_output() so that
anything != 0 will be send down to the driver as "1" not the value
passed in.
- ACPI can now support naming of GPIO lines, hogs and holes in the
GPIO lists.
New drivers:
- The SX150x driver was deemed unfit for the GPIO subsystem and was
moved over to a combined GPIO+pinctrl driver in the pinctrl
subsystem.
New features:
- Various cleanups to various drivers"
* tag 'gpio-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (49 commits)
gpio: merrifield: Implement gpio_get_direction callback
gpio: merrifield: Add support for hardware debouncer
gpio: chardev: Return error for seek operations
gpio: arizona: Tidy up probe error path
gpio: arizona: Remove pointless set of platform drvdata
gpio: pl061: delete platform data handling
gpio: pl061: move platform data into driver
gpio: pl061: rename variable from chip to pl061
gpio: pl061: rename state container struct
gpio: pl061: use local state for parent IRQ storage
gpio: set explicit nesting on drivers
gpio: simplify adding threaded interrupts
gpio: vf610: use builtin_platform_driver
gpio: axp209: use correct register for GPIO input status
gpio: stmpe: fix interrupt handling bug
gpio: em: depnd on ARCH_SHMOBILE
gpio: zx: depend on ARCH_ZX
gpio: x86: update config dependencies for x86 specific hardware
gpio: mb86s7x: use builtin_platform_driver
gpio: etraxfs: use builtin_platform_driver
...
By default all pins are configured to use a glitch filter. Writing 1 to the
certain bit of the specific register might be useful in case someone needs to
bypass the glitch filter completely for a given GPIO pin.
This patch adds support for that in the Intel Merrifield GPIO driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO chardev is used for management tasks (allocating line and event
handles) and does neither support read() nor write() operations. Hence it
does not make much sense to allow seek operations.
Currently the chardev uses noop_llseek() for its seek implementation. This
function does not move the pointer and simply returns the current position
(always 0 for the GPIO chardev). noop_llseek() is primarily meant for
devices that can not support seek, but where there might be a user that
depends on the seek() operation succeeding. For newly added devices that
can not support seek operations it is recommended to use no_llseek(), which
will return an error. For more information see commit 6038f373a3
("llseek: automatically add .llseek fop").
Unfortunately this was overlooked when the GPIO chardev ABI was introduced.
But it is highly unlikely that since then userspace applications have
appeared that rely on being able to perform non-failing seek operations on
a GPIO chardev file descriptor. So it should be safe to change from
noop_llseel() to no_seek(). Also use nonseekable_open() in the chardev
open() callback to clear the FMODE_SEEK, FMODE_PREAD and FMODE_PWRITE flags
from the file. Neither of these should be set on a file that does not
support seek operations.
Cc: stable@vger.kernel.org
Fixes: 3c702e9987 ("gpio: add a userspace chardev ABI for GPIOs")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is some unnecessary complexity in the error path which now things
are converted to devm is actually very simple. This patch simplifies
things.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We use the gpio chip private data in all the callbacks so remove this
redundant line of code.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Platform data is a remnant of board files and all boards using
the PL061 have been migrated to use device tree or ACPI instead.
The custom mechanism to set line by default as inputs/outputs has
been superceded by the GPIO-internal hogging mechanism.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No boardfile defines any PL061 platform data anymore: the
Integrator IM/PD-1 includes the file but is not making use
of the struct. Let's delete the include and all references,
then move the platform data into the driver for later
consolidation into the driver state container.
The only resource defined by the IM/PD-1 is the IRQ which
is passed through the AMBA PrimeCell bus abstraction
struct amba_device.
Cc: arm@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the local variable "chip" referring to the struct pl061
state container to "pl061": we already have gpio_chip and irq_chip
in the driver, we are needlessly adding yet another "chip" to
the confusion.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PL061 state container is named "pl061_gpio", let's rename it
to simply pl061. Less is more.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver is poking around in the struct gpio_chip internals,
which is a no-no. Use a variable in the local state container.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ADNP, CrystalCove and WhiskeyCove are all nested GPIO
irqchips, but were avoiding to connect the parent IRQ to
the gpiochip. This works, but is kind of sloppy as the
child IRQs are not marked as having the parent IRQ as
parent.
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ajay Thomas <ajay.thomas.david.rajamanickam@intel.com>
Cc: Bin Gao <bin.gao@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This tries to simplify the use of CONFIG_GPIOLIB_IRQCHIP when
using threaded interrupts: add a new call
gpiochip_irqchip_add_nested() to indicate that we're dealing
with a nested rather than a chained irqchip, then create a
separate gpiochip_set_nested_irqchip() to mirror
the gpiochip_set_chained_irqchip() call to connect the
parent and child interrupts.
In the nested case gpiochip_set_nested_irqchip() does nothing
more than call irq_set_parent() on each valid child interrupt,
which has little semantic effect in the kernel, but this is
probably still formally correct.
Update all drivers using nested interrupts to use
gpiochip_irqchip_add_nested() so we can now see clearly
which these users are.
The DLN2 driver can drop its specific hack with
.irq_not_threaded as we now recognize whether a chip is
threaded or not from its use of gpiochip_irqchip_add_nested()
signature rather than from inspecting .can_sleep.
We rename the .irq_parent to .irq_chained_parent since this
parent IRQ is only really kept around for the chained
interrupt handlers.
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Daniel Baluta <daniel.baluta@intel.com>
Cc: Bin Gao <bin.gao@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ajay Thomas <ajay.thomas.david.rajamanickam@intel.com>
Cc: Semen Protsenko <semen.protsenko@globallogic.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Phil Reid <preid@electromag.com.au>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO input status was read from control register
(AXP20X_GPIO[210]_CTRL) instead of status register (AXP20X_GPIO20_SS).
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 43db289d00 ("gpio: stmpe: Rework registers access")
reworked the STMPE register access so as to use
[STMPE_IDX_*_LSB + i] to access the 8bit register for a
certain bank, assuming the CSB and MSB will follow after
the enumerator. For this to work the index needs to go from
(size-1) to 0 not 0 to (size-1).
However for the GPIO IRQ handler, the status registers we read
register MSB + 3 bytes ahead for the 24 bit GPIOs and index
registers from MSB upwards and run an index i over the
registers UNLESS we are STMPE1600.
This is not working when we get to clearing the interrupt
EDGE status register STMPE_IDX_GPEDR_[LCM]SB: it is indexed
like all other registers [STMPE_IDX_*_LSB + i] but in this
loop we index from 0 to get the right bank index for the
calculations, and we need to just add i to the MSB.
Before this, interrupts on the STMPE2401 were broken, this
patch fixes it so it works again.
Cc: stable@vger.kernel.org
Cc: Patrice Chotard <patrice.chotard@st.com>
Fixes: 43db289d00 ("gpio: stmpe: Rework registers access")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO_EM is part of the Renesas SoCs so depend on the arch.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
[Changed to depend on ARCH_EMEV2]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set GPIO_ZX to depend on ARCH_ZX as it's SOC specific.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The devices here are specific to x86 so lets depend on x86.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adding max20024 compatible string to the device id list
to support both max77620 and max20024 devices.
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This option was added in 6a89a314ab to
allow use of the devm_gpio_* functions without CONFIG_GPIOLIB.
However, only a few months later in
b69ac52449, CONFIG_GPIOLIB was added
as a dependency, defeating the original purpose of this option.
Instead of that patch, the original commit could have just been
reverted (and in fact was partially so in
403c1d0be5). Further, since this
option has a dependency on HAS_IOMEM, even though it does not
require it, it causes build failures when !HAS_IOMEM (e.g. in a
uml build).
Fix that by completely removing the option, in essence completing
the reversion of the original commit.
Signed-off-by: Keno Fischer <keno@juliacomputing.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use builtin_pci_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The bit in the TC3589x direction register is 0 for input
and 1 for output, but the gpiolib expects the reverse.
Fix up the logic.
Cc: stable@vger.kernel.org
Fixes: 14063d71e5 ("gpio: tc3589x: add .get_direction() and small cleanup")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When a GPIO line is marked as used for an interrupt, it is
helpful to set the label to "interrupt" so we know what is
going on when inspecting the lines.
If a GPIO is already properly named by gpiod_get*() we don't
need to do this. It only happens when a line is used from
the irqchip side of a GPIO driver without communicating
with the GPIO side, such as when gpiochip is used as interrupt
provider in the device tree.
If the line is still marked as used by "interrupt" when we
unmark it as used by an interrupt, also remove this label
from the descriptor.
Also shape up the code around unmarking IRQ lines.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I saw weird values != [0,1] being passed down to drivers
in their .set_direction_output() callbacks. Go over the
gpiolib and make sure to hammer it to [0,1] before hitting
the driver to avoid undesired side effects.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When locking a GPIO line as IRQ, we go to lengths to
double-check that the line is really set as input before
marking it as used for IRQ. This is not good on GPIO chips
that can sleep, because this function is called in IRQ-safe
context. Just skip this if it can't be checked quickly.
Currently this happens on sleeping expanders such as STMPE
or TC3589x:
BUG: scheduling while atomic: swapper/1/0x00000002
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.9.0-rc1+ #38
Hardware name: Nomadik STn8815
[<c000f2e0>] (unwind_backtrace) from [<c000d244>] (show_stack+0x10/0x14)
[<c000d244>] (show_stack) from [<c0037b78>] (__schedule_bug+0x54/0x80)
[<c0037b78>] (__schedule_bug) from [<c042df14>] (__schedule+0x3a0/0x460)
[<c042df14>] (__schedule) from [<c042e028>] (schedule+0x54/0xb8)
(...)
This patch fixes that problem and relies on the direction
read from the chip when it was added.
Cc: stable@vger.kernel.org
Fixes: 9c10280d85 ("gpio: flush direction status in gpiochip_lock_as_irq()")
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the hardware is in output mode, reading the value from the
hardware is not giving the correct value back. Instead read the
value from the cache so we get the right value.
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes is possible to read out the current direction of a
GPIO line on the HTC CPLD GPIO expander.
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The newly added acpi_gpiochip_scan_gpios function produces a few harmless
warnings:
drivers/gpio/gpiolib-acpi.c: In function ‘acpi_gpiochip_add’:
drivers/gpio/gpiolib-acpi.c:925:7: error: ‘dflags’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/gpio/gpiolib-acpi.c:925:9: error: ‘lflags’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
The problem is that he compiler cannot know that a negative return value
from fwnode_property_read_u32_array() or acpi_gpiochip_pin_to_gpio_offset()
implies that the IS_ERR(gpio_desc) is true, as the value could in theory
be below -MAX_ERRNO.
The function already initializes its output values to zero, and moving
that intialization a little higher up ensures that we can never have
uninitialized data in the caller.
Fixes: c80f1ba75d ("ACPI / gpio: Add hogging support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpiod framework uses the chip label to match a specific chip.
The davinci gpio driver, creates several chips using always the same
label, which is not compatible with gpiod.
To allow platform data to declare gpio lookup tables, and for drivers
to use the gpiod framework, allocate unique label per registered chip.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Need to ensure that reg_output is not updated while setting multiple
bits. This makes the mutex locking behaviour for the set_multiple call
consistent with that of the set_value call.
Cc: stable@vger.kernel.org
Fixes: b4818afeac ("gpio: pca953x: Add set_multiple to allow multiple")
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiod_set_array_value_complex does not clear the bits field.
Therefore when the drivers set_multiple funciton is called bits outside
the mask are undefined and can be either set or not. So bank_val needs
to be masked with bank_mask before or with the reg_val cache.
Cc: stable@vger.kernel.org
Fixes: b4818afeac ("gpio: pca953x: Add set_multiple to allow multiple")
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/gpio/Kconfig:config HTC_EGPIO
drivers/gpio/Kconfig: bool "HTC EGPIO support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Kevin O'Connor <kevin@koconnor.net>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes the irq allocation in this driver to not print:
irq: Cannot allocate irq_descs @ IRQ34, assuming pre-allocated
irq: Cannot allocate irq_descs @ IRQ66, assuming pre-allocated
Which happens because the driver already called irq_alloc_descs()
and so the change to use irq_domain_add_simple resulted in calling
irq_alloc_descs() twice.
Modernize the irq allocation in this driver to use the
irq_domain_add_linear flow directly and eliminate the use of
irq_domain_add_simple/legacy
Fixes: ce931f571b ("gpio/mvebu: convert to use irq_domain_add_simple()")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Sylvain Lemieux reports the LPC32xx GPIO driver is broken since
commit 762c2e46c0 ("gpio: of: remove of_gpiochip_and_xlate() and
struct gg_data"). Probably, gpio-etraxfs.c and gpio-davinci.c are
broken too.
Those drivers register multiple gpio_chip that are associated to a
single OF node, and their own .of_xlate() checks if the passed
gpio_chip is valid.
Now, the problem is of_find_gpiochip_by_node() returns the first
gpio_chip found to match the given node. So, .of_xlate() fails,
except for the first GPIO bank.
Reverting the commit could be a solution, but I do not want to go
back to the mess of struct gg_data. Another solution here is to
take the match by a node pointer and the success of .of_xlate().
It is a bit clumsy to call .of_xlate twice; for gpio_chip matching
and for really getting the gpio_desc index. Perhaps, our long-term
goal might be to convert the drivers to single chip registration,
but this commit will solve the problem until then.
Fixes: 762c2e46c0 ("gpio: of: remove of_gpiochip_and_xlate() and struct gg_data")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When allocating a new line handle or event a file is allocated that it is
associated to. The file is attached to a file descriptor of the current
process and the file descriptor is returned to userspace using
copy_to_user(). If this copy operation fails the line handle or event
allocation is aborted, all acquired resources are freed and an error is
returned.
But the file struct is not freed and left attached to the userspace
application and even though the file descriptor number was not copied it is
trivial to guess. If a userspace application performs a IOCTL on such a
left over file descriptor it will trigger a use-after-free and if the file
descriptor is closed (latest when the application exits) a double-free is
triggered.
anon_inode_getfd() performs 3 tasks, allocate a file struct, allocate a
file descriptor for the current process and install the file struct in the
file descriptor. As soon as the file struct is installed in the file
descriptor it is accessible by userspace (even if the IOCTL itself hasn't
completed yet), this means uninstalling the fd on the error path is not an
option, since userspace might already got a reference to the file.
Instead anon_inode_getfd() needs to be broken into its individual steps.
The allocation of the file struct and file descriptor is done first, then
the copy_to_user() is executed and only if it succeeds the file is
installed.
Since the file struct is reference counted it can not be just freed, but
its reference needs to be dropped, which will also call the release()
callback, which will free the state attached to the file. So in this case
the normal error cleanup path should not be taken.
Cc: stable@vger.kernel.org
Fixes: d932cd4918 ("gpio: free handles in fringe cases")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When terminating for_each_available_child_of_node() iteration
with break or return, of_node_put() should be used to prevent
stale device node references from being left behind.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes the following sparse warning:
drivers/gpio/gpiolib-acpi.c:863:18: warning:
symbol 'acpi_gpiochip_parse_own_gpio' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
fwnode_handle_put() should be used when terminating
device_for_each_child_node() iteration with break or
return to prevent stale device node references from
being left behind.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently read directly calls the repmap read function. Hence
remove the redundant wrapper and use regmap read wherever
needed.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Confirm the chip->parent is valid before dereferencing because
the parent parameter is optional.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's not necessary to unregister gpio_chip which registered
with devm_gpiochip_add_data().
Also get rid of useless altr_a10sr_gpio_remove().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to the reference manual level interrupts can't be acked
using the IRQSTAT registers. The effect is that when a level interrupt
triggers the following ack is a no-op and the same interrupt triggers
again right after it has been unmasked after running the interrupt
handler.
The reference manual says:
Status bits for pins configured as level sensitive interrupts cannot be
cleared unless either the actual pin is in the non-interrupting state, or
the pin has been disabled as an interrupt source by clearing its bit in
HW_PINCTRL_PIN2IRQ.
To work around the duplicated interrupts we can use the PIN2IRQ
rather than the IRQEN registers to mask the interrupts. This
probably does not work for the edge interrupts, so we have to split up
the irq chip into two chip types, one for the level interrupts and
one for the edge interrupts. We now make use of two different enable
registers, so we have to take care to always enable the right one,
especially during switching of the interrupt type. An easy way
to accomplish this is to use the IRQCHIP_SET_TYPE_MASKED which
makes sure that set_irq_type is called with masked interrupts. With this
the flow to change the irq type is like:
- core masks interrupt (using the current chip type)
- mxs_gpio_set_irq_type() changes chip type if necessary
- mxs_gpio_set_irq_type() unconditionally sets the enable bit in the
now unused enable register
- core eventually unmasks the interrupt (using the new chip type)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mxs gpio controller does not only have a mask register to mask
interrupts, but also enable/disable registers. Use the enable/disable
registers rather than the mask register. This does not have any
advantage for now, but makes the next patch simpler.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we have the new helper function that sets nice names for GPIO
lines based on "gpio-line-names" device property, we can take advantage of
this in acpi_gpiochip_add().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to use "gpio-line-names" property in systems not having DT as
their boot firmware, rework of_gpiochip_set_names() to use device property
accessors. This reworked function is placed in a separate file making it
clear it deals with universal device properties.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO hogging means that the GPIO controller can "hog" and configure certain
GPIOs without need for a driver or userspace to do that. This is useful in
open-connected boards where BIOS cannot possibly know beforehand which
devices will be connected to the board.
This adds GPIO hogging mechanism to ACPI analogous to Device Tree.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make it possible to have an empty GPIOs in a GPIO list for device. For
example a SPI master may use both GPIOs and native pins as chip selects and
we need to be able to distinguish between the two.
This makes it mandatory to have exactly 3 arguments for GPIOs and then
converts gpiolib to use of __acpi_node_get_property_reference() instead. In
addition we make acpi_gpio_package_count() to handle holes as well (this
matches the DT version).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add compatible string for the MAX7318 part. This is a two bank,
16 lines, I2C GPIO expander with interrupt line.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All the boards supported by the gpio-ts4900 driver are i.MX6 boards,
so only offer the driver for building on this platform, unless
build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Lucile Quirion <lucile.quirion@savoirfairelinux.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the GPIO functionality for the Altera Arria10 MAX5 System Resource
Chip. The A10 MAX5 has 12 bits of GPIO assigned to switches, buttons,
and LEDs as a GPIO extender on the SPI bus.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>i
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We switch the default handler to be handle_bad_irq() instead of
handle_simple_irq() (which was not correct anyway).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current code does not use gpio_irq/irq_base/gpio_base fields from
struct max77620_gpio, so remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the I2C sx150x GPIO expander driver uses platform_data to manage
the pins configurations, rewrite the driver as a pinctrl driver using
pinconf to get/set pin configurations from DT or debugfs.
The pinctrl driver is functionnally equivalent as the gpio-only driver
and can use DT for pinconf. The platform_data confirmation is dropped.
This patchset removed the gpio-only driver and selects the Pinctrl driver
config instead. This patchset also migrates the gpio dt-bindings to pinctrl
and add the pinctrl optional properties.
The driver was tested with a SX1509 device on a BeagleBone black with
interrupt support and on an X86_64 machine over an I2C to USB converter.
This is a fixed version that builds and runs on non-OF platforms and on
arm based OF. The GPIO version is removed and the bindings are also moved
to the pinctrl bindings.
Changes since v2
- rebased on v4.9-rc1
- removed MODULE_DEVICE_TABLE as in upstream bb411e771b
("gpio: sx150x: fix implicit assumption module.h is present")
Changes since v1
- Fix Kconfig descriptions on pinctrl and gpio
- Fix Kconfig dependency
- Remove oscio support for non-789 devices
- correct typo in dt bindings
- remove probe reset for non-789 devices
Changes since RFC
- Put #ifdef CONFIG_OF/CONFIG_OF_GPIO to remove OF code for non-of platforms
- No more rely on OF_GPIO config
- Moved and enhanced bindings to pinctrl bindings
- Removed gpio-sx150x.c
- Temporary select PINCTRL_SX150X when GPIO_SX150X
- Temporary mark GPIO_SX150X as deprecated
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
ested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
From the beginning of the gpio-mpc8xxx.c, the "handle_level_irq"
has being used to handle GPIO interrupts in the PowerPC/Layerscape
platforms. But actually, almost all PowerPC/Layerscape platforms
assert an interrupt request upon either a high-to-low change or
any change on the state of the signal.
So the "handle_level_irq" is not reasonable for PowerPC/Layerscape
GPIO interrupt, it should be "handle_edge_irq". Otherwise the system
may lost some interrupts from the PIN's state changes.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/gpio/gpio-ath79.ko | grep alias
$
After this patch:
$ modinfo drivers/gpio/gpio-ath79.ko | grep alias
alias: of:N*T*Cqca,ar9340-gpioC*
alias: of:N*T*Cqca,ar9340-gpio
alias: of:N*T*Cqca,ar7100-gpioC*
alias: of:N*T*Cqca,ar7100-gpio
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Aban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/gpio/gpio-ts4800.ko | grep alias
$
After this patch:
$ modinfo drivers/gpio/gpio-ts4800.ko | grep alias
alias: of:N*T*Ctechnologic,ts4800-gpioC*
alias: of:N*T*Ctechnologic,ts4800-gpio
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO_GET_LINEEVENT_IOCTL currently ignores unknown or undefined
linehandle and lineevent flags. From a backwards and forwards compatibility
viewpoint it is highly desirable to reject unknown flags though.
On one hand an application that is using newer flags and is running on
an older kernel has no way to detect if the new flags were handled
correctly if they are silently discarded.
On the other hand an application that (accidentally) passes undefined flags
will run fine on an older kernel, but may break on a newer kernel when
these flags get defined.
Ensure that requests that have undefined flags set are rejected with an
error, rather than silently discarding the undefined flags.
Cc: stable@vger.kernel.org
Fixes: 61f922db72 ("gpio: userspace ABI for reading GPIO line events")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO_GET_LINEHANDLE_IOCTL currently ignores unknown or undefined
linehandle flags. From a backwards and forwards compatibility viewpoint it
is highly desirable to reject unknown flags though.
On one hand an application that is using newer flags and is running on
an older kernel has no way to detect if the new flags were handled
correctly if they are silently discarded.
On the other hand an application that (accidentally) passes undefined flags
will run fine on an older kernel, but may break on a newer kernel when
these flags get defined.
Ensure that requests that have undefined flags set are rejected with an
error, rather than silently discarding the undefined flags.
Cc: stable@vger.kernel.org
Fixes: d7c51b47ac ("gpio: userspace ABI for reading/writing GPIO lines")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIOHANDLE_GET_LINE_VALUES_IOCTL handler allocates a gpiohandle_data
struct on the stack and then passes it to copy_to_user(). But depending on
the number of requested line handles the struct is only partially
initialized.
This exposes the previous, potentially sensitive, stack content to the
issuing userspace application. To avoid this make sure that the struct is
fully initialized.
Cc: stable@vger.kernel.org
Fixes: d7c51b47ac ("gpio: userspace ABI for reading/writing GPIO lines")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The line offset that is used as an index into the descs array is provided
by userspace and might go beyond the bounds of the array. If that happens
undefined behavior will occur.
Make sure that the offset is within the bounds of the desc array and reject
any requests that specify a value outside of it.
Cc: stable@vger.kernel.org
Fixes: 61f922db72 ("gpio: userspace ABI for reading GPIO line events")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIOHANDLE_GET_LINE_VALUES_IOCTL handler allocates a gpiohandle_data
struct on the stack and then passes it to copy_to_user(). But only the
first element of the values array in the struct is set, which leaves the
struct partially initialized.
This exposes the previous, potentially sensitive, stack content to the
issuing userspace application. To avoid this make sure that the struct is
fully initialized.
Cc: stable@vger.kernel.org
Fixes: 61f922db72 ("gpio: userspace ABI for reading GPIO line events")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The line offset that is used as an index into the descs array is provided
by userspace and might go beyond the bounds of the array. If that happens
undefined behavior will occur.
Make sure that the offset is within the bounds of the desc array and reject
any requests that specify a value outside of it.
Cc: stable@vger.kernel.org
Fixes: d7c51b47ac ("gpio: userspace ABI for reading/writing GPIO lines")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO_GET_CHIPINFO_IOCTL handler allocates a gpiochip_info struct on the
stack and then passes it to copy_to_user(). But depending on the length of
the GPIO chip name and label the struct is only partially initialized.
This exposes the previous, potentially sensitive, stack content to the
issuing userspace application. To avoid this make sure that the struct is
fully initialized.
Cc: stable@vger.kernel.org
Fixes: 521a2ad6f8 ("gpio: add userspace ABI for GPIO line information")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current line offset validation is off by one. Depending on the data
stored behind the descs array this can either cause undefined behavior or
disclose arbitrary, potentially sensitive, memory to the issuing userspace
application.
Make sure that offset is within the bounds of the desc array.
Cc: stable@vger.kernel.org
Fixes: 521a2ad6f8 ("gpio: add userspace ABI for GPIO line information")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
acpi_dev_gpio_irq_get() currently ignores the error returned
by acpi_get_gpiod_by_index() and overwrites it with -ENOENT.
Problem is this error can be -EPROBE_DEFER, which just blows
up some drivers when the module ordering is not correct.
Cc: stable@vger.kernel.org
Signed-off-by: David Arcari <darcari@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Building the gpio-mockup driver without SYSFS results in a harmless Kconfig
warning:
warning: (GPIO_MOCKUP) selects GPIO_SYSFS which has unmet direct dependencies (GPIOLIB && SYSFS)
We can easily avoid that warning by adding a dependency on SYSFS.
Fixes: 0f98dd1b27 ("gpio/mockup: add virtual gpio device")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
&& was obviously intended here.
Fixes: 6936e1f88d ('gpio: stmpe: Write int status register only when needed')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a follow-up to commit 559b46990e ("gpio: pca953x: fix an
incorrect lockdep warning"). The reason for calling
lockdep_set_subclass() in pca953x_probe() is not explained in
the code.
Add a comment describing the problem, partial solution and required
future extensions.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Here is the 4.9 pull request from I2C including:
- centralized error messages when registering to the core
- improved lockdep annotations to prevent false positives
- DT support for muxes, gates, and arbitrators
- bus speeds can now be obtained from ACPI
- i2c-octeon got refactored and now supports ThunderX SoCs, too
- i2c-tegra and i2c-designware got a bigger bunch of updates
- a couple of standard driver fixes and improvements"
* 'i2c/for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (71 commits)
i2c: axxia: disable clks in case of failure in probe
i2c: octeon: thunderx: Limit register access retries
i2c: uniphier-f: fix misdetection of incomplete STOP condition
gpio: pca953x: variable 'id' was used twice
i2c: i801: Add support for Kaby Lake PCH-H
gpio: pca953x: fix an incorrect lockdep warning
i2c: add a warning to i2c_adapter_depth()
lockdep: make MAX_LOCKDEP_SUBCLASSES unconditionally visible
i2c: export i2c_adapter_depth()
i2c: rk3x: Fix variable 'min_total_ns' unused warning
i2c: rk3x: Fix sparse warning
i2c / ACPI: Do not touch an I2C device if it belongs to another adapter
i2c: octeon: Fix high-level controller status check
i2c: octeon: Avoid sending STOP during recovery
i2c: octeon: Fix set SCL recovery function
i2c: rcar: add support for r8a7796 (R-Car M3-W)
i2c: imx: make bus recovery through pinctrl optional
i2c: meson: add gxbb compatible string
i2c: uniphier-f: set the adapter to master mode when probing
i2c: uniphier-f: avoid WARN_ON() of clk_disable() in failure path
...
Subsystem improvements:
- Do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to
me). We can now select GPIOLIB and be done with it, for all
archs. After some struggle it even work on UM. Not that it has
GPIO, but if it wants to, it can select the library.
- Continued efforts to make drivers properly either tristate or
bool.
- Introduce a warning for drivers assigning default triggers to
their irqchip lines when probed from device tree, so we find and
fix these ambigous drivers. It is agreed that in the OF config
path, the device tree defines trigger characteristics.
- The same warning, mutatis mutandis, for ACPI-probed GPIO
irqchips.
- We introduce the ability to mark certain IRQ lines as "unusable"
as they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is
put to good use in the STMPE driver and also in the Cherryview
pin control driver.
- A new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- Make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM
with allyesconfig or allmodconfig it exploded in their face.
- Move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so
now eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- New driver for the Aspeed GPIO front-end companion to the
pin controller merged through the pin control tree.
- New driver for the LP873x PMIC GPIO portions.
- New driver for Technologic Systems' I2C FPGA GPIO such as
TS4900, TS-7970, TS-7990 and TS-4100.
- New driver for the Broadcom BCM63xx series including BCM6338
and BCM6345.
- New driver for the Intel WhiskeyCove PMIC GPIO.
- New driver for the Allwinner AXP209 PMIC GPIO portions.
- New driver for Diamond Systems 48 line GPIO-MM, another of
these port-mapped I/O expansion cards.
- Support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- The STMPE driver now supports rising/falling edge detection
properly for IRQs.
- The PCA954x will now fetch and enable its VCC regulator properly.
- Major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- Switch the IOP driver to use the generic MMIO GPIO library.
- Move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns.
-----BEGIN PGP SIGNATURE-----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=ABbi
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.9 series:
Subsystem improvements:
- do away with the last users of the obsolete Kconfig options
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB (the latter
always sounded like an item on a wishlist to Santa Claus to me). We
can now select GPIOLIB and be done with it, for all archs. After
some struggle it even work on UM. Not that it has GPIO, but if it
wants to, it can select the library.
- continued efforts to make drivers properly either tristate or bool.
- introduce a warning for drivers assigning default triggers to their
irqchip lines when probed from device tree, so we find and fix
these ambigous drivers. It is agreed that in the OF config path,
the device tree defines trigger characteristics.
- the same warning, mutatis mutandis, for ACPI-probed GPIO irqchips.
- we introduce the ability to mark certain IRQ lines as "unusable" as
they can be taken by BIOS/firmware, unrouted in silicon and
generally nasty if you use them, and such things. This is put to
good use in the STMPE driver and also in the Cherryview pin control
driver.
- a new "mockup" virtual GPIO device that can be used for testing.
The plan is to add unit tests under tools/* for exercising this
device and verify that the kernel code paths are working as they
should.
- make memory-mapped I/O-drivers depend on HAS_IOMEM. This was
implicit all the time, but when people started building UM with
allyesconfig or allmodconfig it exploded in their face.
- move some stray bits of device tree and ACPI HW description
callbacks down into their respective implementation silo. These
were causing issues when compiling on !HAS_IOMEM as well, so now
eventually UM compiles the GPIOLIB library if it wants to.
New drivers:
- new driver for the Aspeed GPIO front-end companion to the pin
controller merged through the pin control tree.
- new driver for the LP873x PMIC GPIO portions.
- new driver for Technologic Systems' I2C FPGA GPIO such as TS4900,
TS-7970, TS-7990 and TS-4100.
- new driver for the Broadcom BCM63xx series including BCM6338 and
BCM6345.
- new driver for the Intel WhiskeyCove PMIC GPIO.
- new driver for the Allwinner AXP209 PMIC GPIO portions.
- new driver for Diamond Systems 48 line GPIO-MM, another of these
port-mapped I/O expansion cards.
- support the STMicroelectronics STMPE1600 variant in the STMPE
driver.
Driver improvements:
- the STMPE driver now supports rising/falling edge detection
properly for IRQs.
- the PCA954x will now fetch and enable its VCC regulator properly.
- major rework of the PCA953x driver with the goal of eventually
switching it over to use regmap and thus modernize it even more.
- switch the IOP driver to use the generic MMIO GPIO library.
- move the ages old HTC EGPIO (extended GPIO) GPIO expander driver
over to this subsystem from MFD, achieveing some separation of
concerns"
* tag 'gpio-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (81 commits)
gpio: add missing static inline
gpio: OF: localize some gpiochip init functions
gpio: acpi: separation of concerns
gpio: OF: separation of concerns
gpio: make memory-mapped drivers depend on HAS_IOMEM
gpio: stmpe: use BIT() macro
gpio: stmpe: forbid unused lines to be mapped as IRQs
mfd/gpio: Move HTC GPIO driver to GPIO subsystem
gpio: MAINTAINERS: Add an entry for GPIO mockup driver
gpio/mockup: add virtual gpio device
gpio: Added zynq specific check for special pins on bank zero
gpio: axp209: Implement get_direction
gpio: aspeed: remove redundant return value check
gpio: loongson1: remove redundant return value check
ARM: omap2: fix missing include
gpio: tc3589x: fix up complaints on unsigned
gpio: tc3589x: add .get_direction() and small cleanup
gpio: f7188x: use gpiochip_get_data instead of container_of
gpio: tps65218: use devm_gpiochip_add_data() for gpio registration
gpio: aspeed: fix return value check in aspeed_gpio_probe()
...
of_get_named_gpiod_flags() was missing a static inline version
when compiling without OF_GPIO. Add this.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_gpiochip_add() and of_gpiochip_remove() are only used locally
in the gpio subsystem so move these functions to the local
header.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The generic GPIO library directly implement code for acpi_find_gpio()
which is only used with CONFIG_ACPI. This was probably done because
OF did the same thing, but I removed that so remove this too.
Rename the internal acpi_find_gpio() in gpiolib-acpi.c to
acpi_populate_gpio_lookup() which seems to be more appropriate anyway
so as to avoid a namespace clash with the same function.
Make the stub return -ENOENT rather than -ENOSYS (as that is for
syscalls!).
For some reason the sunxi pin control driver was including the private
gpiolib header, it works just fine without it so remove that oneliner.
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The generic GPIO library directly implement code for of_find_gpio()
which is only used with CONFIG_OF and causes compilation problems
on archs that do not even have stubs for OF functions, especially
on UM that does not implement any IO remap functions.
Move the function to gpiolib-of.c, implement a static inline stub
in gpiolib.h returning PTR_ERR(-ENOENT) if CONFIG_OF_GPIO is not
set and be done with it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This one is pretty obvious: on UM Linux compilation of things
like allmodconfig and allyesconfig will fail due to the
absence of IO memory. Simply make these drivers depend on
HAS_IOMEM, it has been implicitly assumed all the time, so
just make it explicit.
The generic MMIO library also assumes that IOMEM is present
so make also this depend on HAS_IOMEM.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Arvind Yadav