Currently packed pixel modes in MHL2 can't be displayed. The device
automatically recognizes output format, so setting format other than
RGB causes failure. Fix it by writing proper values to registers.
Tested on MHL1 and MHL2 using various vendors' dongles both in
DVI and HDMI mode.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1516706239-9104-1-git-send-email-m.purski@samsung.com
MHL bridge is usually connected to TV via MHL dongle. Currently plugging
HDMI cable to dongle is handled improperly.
Fix it by splitting connecting of a dongle and a HDMI cable. The driver
should now handle unplugging a sink from a dongle and plugging a
different sink with new edid.
Tested on MHL1, MHL2 and MHL3 using various vendors' dongles both in
DVI and HDMI mode.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1516705996-8928-1-git-send-email-m.purski@samsung.com
HSIC initialization was taken from the vendor code. HSIC in MHL circuit
is not connected, so it is not possible to test it. Tests prove that
without HSIC the device works well. Therefore it can be removed.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1511968368-30884-1-git-send-email-m.purski@samsung.com
The vendor code waits for infoframe to detect video mode set by source.
We do not need to follow this pattern, because video mode information is
provided by drm core. As a result most of the infoframe handling
code can be removed.
Start transmission immediately after detecting stream on HDMI lines
in irq_scdt() function without waiting for infoframe interrupt.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1511956130-24482-1-git-send-email-m.purski@samsung.com
Buffer overflow error should not occur, as mode_fixup() callback
filters pixel clock value and it should never exceed 600000. However,
current implementation is not obviously safe and relies on
implementation of mode_fixup().
Make 'i' variable never reach unsafe value in order to avoid buffer
overflow error.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: bf1722ca ("drm/bridge/sii8620: rewrite hdmi start sequence")
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1511341718-6974-1-git-send-email-m.purski@samsung.com
There is no need to flip reset pin twice. Also delays can be changed to
values present in vendor's code.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Maciej Purski <m.purski@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180608060457.18357-1-a.hajda@samsung.com
Currently MHL chip must be turned on permanently to detect MHL cable. It
duplicates micro-USB controller's (MUIC) functionality and consumes
unnecessary power. Lets use extcon attached to MUIC to enable MHL chip
only if it detects MHL cable.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Appedix F of HDMI 2.0 says that some HDMI sink may fail to switch from
3D to 2D mode in a timely fashion if the source simply stops sending the
HDMI infoframe. The suggested workaround is to keep sending the
infoframe even when strictly not necessary (ie. no VIC and no S3D).
HDMI 1.4 does allow for this behaviour, stating that sending the
infoframe is optional in this case.
The infoframe was first specified in HDMI 1.4, so in theory sinks
predating that may not appreciate us sending an uknown infoframe
their way. To avoid regressions let's try to determine if the sink
supports the infoframe or not. Unfortunately there's no direct way
to do that, so instead we'll just check if we managed to parse any
HDMI 1.4 4k or stereo modes from the EDID, and if so we assume the
sink will accept the infoframe. Also if the EDID contains the HDMI
2.0 HDMI Forum VSDB we can assume the sink is prepared to receive
the infoframe.
v2: Fix getting has_hdmi_infoframe from display_info
Always fail constructing the infoframe if the display
possibly can't handle it
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171113170427.4150-3-ville.syrjala@linux.intel.com
If the sink device is in HDMI mode, enable infoframe interrupt in scdt
irq handle function else call start_video function immediately, because
in DVI mode, there is no infoframe interrupt provided.
Rename start_hdmi function to start_video and get rid of the old
start_video function. In start_video, if the sink is DVI and mode is
MHL1 or MHl2, write appropriate values to registers else the path
should remain the same as in HDMI mode.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1510224822-7732-1-git-send-email-m.purski@samsung.com
The maximum pixel clock depends on the version of the connected MHL
adapter. Add mode_valid callback to filter out modes with too high pixel
clock to avoid failure in mode_fixup later.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171109102831.19844-1-m.szyprowski@samsung.com
MHL specification defines Remote Control Protocol(RCP) to
send input events between MHL devices.
The driver now recognizes RCP messages and reacts to them
by reporting key events to input subsystem, allowing
a user to control a device using TV remote control.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Acked-by: Sean Young <sean@mess.org>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1503565087-19730-1-git-send-email-m.purski@samsung.com
Function sii8620_mt_read_devcap_reg_recv() used to read array index
from a wrong msg register, which caused writing out of array
bounds. It led to writing on other fields of struct sii8620.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Fixes: e9c6da270 ("drm/bridge/sii8620: add reading device capability
registers")
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1503311571-25819-1-git-send-email-m.purski@samsung.com
Since all sub-protocols of MHL3 are already supported MHL3 mode can be
enabled. With this patch it is possible to use packed pixel modes and
clocks up to 300MHz - 1920x1080@60Hz and 4K modes.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-25-git-send-email-a.hajda@samsung.com
MHL3 protocol requires registry adjustments depending on chosen video mode.
Necessary information is gathered in mode_fixup callback. In case of HDMI
video modes driver should also send special AVI and MHL3 infoframes.
The patch introduces generic helpers for handling MHL3 infoframes, in
case of appearance of other users of MHL3 infoframes these function can
be moved to common library.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-21-git-send-email-a.hajda@samsung.com
The Single-ended eCBUS Mode (eCBUS-S) mode provides 60 Mb/s full-duplex
bidirectional traffic for three channels:
- CBUS data (CBUS1 channel),
- High-bandwidth MHL data (eMSC channel),
- tunneling data (T-CBUS channel).
It is required to fully support MHL3 dongles.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-6-git-send-email-a.hajda@samsung.com
Due to asynchronous nature of MHL flow of execution is dispersed.
Logical continuation of some actions happens after response of peer,
i.e in interrupt handler. To simplify coding continuation mechanism
has been added - it is now possible to provide continuation callback,
which will be called after peer responds to given action.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-5-git-send-email-a.hajda@samsung.com
drivers/gpu/drm/bridge/sil-sii8620.c:1556:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161026165836.GA98766@lkp-sb04.lkp.intel.com
SiI8620 transmitter converts eTMDS/HDMI signal to MHL 3.0.
It is controlled via I2C bus. Its interaction with other
devices in video pipeline is performed mainly on HW level.
The only interaction it does on device driver level is
filtering-out unsupported video modes, it exposes drm_bridge
interface to perform this operation.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1476085157-5266-1-git-send-email-a.hajda@samsung.com
Maciej Purski