When using DT, dss device does not have platform data. However,
dss_get_ctx_loss_count() uses dss device's platform data to find the
get_ctx_loss_count function pointer.
To fix this, dss_get_ctx_loss_count() needs to be changed to get the
platform data from the omapdss device, which is a "virtual" device and
always has platform data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSS func clock is calculated with prate / div * m. However, the current
omapdss code calculates it with prate * m / div, which yields a slightly
different result when there's a remainder. For example, 432000000 / 14 *
2 = 61714284, but 432000000 * 2 / 14 = 61714285.
In addition to that, the clock framework wants the clock rate given with
clk_set_rate to be higher than the actual (truncated) end result. So, if
prate is 432000000, and div is 14, the real result is 30857142.8571...
We need to call clk_set_rate with 30857143, which gives us a clock of
30857142. That's why we need to use DIV_ROUND_UP() when calling
clk_set_rate.
This patch fixes the clock calculation.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use devm_clk_get() instead of clk_get() for dss, and for outputs hdmi
and venc. This reduces code and simplifies error handling.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add new way to iterate over DSS clock divisors. dss_div_calc() provides
a generic way to go over all the divisors, within given clock range.
dss_div_calc() will call a callback function for each divider set,
making the function reusable for all use cases.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Dispc currently gets dispc's fck with clk_get() and uses clk_get_rate()
to get the rate for scaling calculations. This causes a problem with
common clock framework, as omapdss uses the dispc functions inside a
spinlock, and common clock framework uses a mutex in clk_get_rate().
Looking at the DSS clock tree, the above use of the dispc fck is not
quite correct. The DSS_FCLK from PRCM goes to DSS core block, which has
a mux to select the clock for DISPC from various options, so the current
use of dispc fck bypasses that. Fortunately we never change the dispc
clock mux for now.
To fix the issue with clk_get_rate(), this patch caches the dss clock
rate in dss.c when it is set. Dispc will then ask for the clock rate
from dss. While this is not very elegant, it does fix the issue, and
it's not totally wrong when considering that the dispc fck actually
comes via dss.
In the future we should probably look into common clock framework and
see if that could be used to represent the DSS clock tree properly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When enabling a hwmod, omap_hwmod refers to the register mentioned in the
hwmod struct's member 'prcm.omap4.context_offs' to see whether context was
lost or not. It increments the context lost count for the hwmod and then clears
the register.
All the DSS hwmods have the same register(RM_DSS_DSS_CONTEXT) as context_offs.
When DSS is enabled, the first hwmod to be enabled is the "dss_core" hwmod since
it's corresponding platform device is the parent platform device("omapdss_dss").
The dss_core hwmod updates it's context lost count correctly and clears the
register. When the hwmods corresponding to the children platform devices are
enabled, they see that the register is clear, and don't increment their context
lost count. Therefore, all the children platform devices never report a loss in
context.
The DISPC driver currently gets the context lost count for DSS power domain from
it's corresponding platform device instance("omapdss_dispc"). The DISPC platform
device is one of the child devices, and it's corresponding hwmod("dss_dispc")
doesn't report the context lost count correctly.
Modify dss_get_ctx_loss_count() such that it always takes the "omapdss_dss"
platform device as it's input, move the function to dss.c so that it has access
to that platform device.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Do not fail if dpll4_m4_ck is missing. The clock is not there on omap24xx,
so this should not be a hard error.
The patch retains the functionality before the commit 185bae10 (OMAPDSS:
DSS: Cleanup cpu_is_xxxx checks).
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss.c currently exposes functions to configure the dispc source clock
and lcd source clock. There are configured separately from the output
drivers.
However, there is no safe way for the output drivers to handle dispc
clock, as it's shared between the outputs. Thus, if, say, the DSI driver
sets up DSI PLL and configures both the dispc and lcd clock sources to
that DSI PLL, the resulting dispc clock could be too low for, say, HDMI.
Thus the output drivers should really only be concerned about the lcd
clock, which is what the output drivers actually use. There's lot to do
to clean up the dss clock handling, but this patch takes one step
forward and removes the use of dss_select_dispc_clk_source() from the
output drivers.
After this patch, the output drivers only configure the lcd source
clock. On omap4+ the dispc src clock is never changed from the default
PRCM source. On omap3, where the dispc and lcd clocks are actually the
same, setting the lcd clock source sets the dispc clock source.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We don't currently set the dss fck when starting up. This is not a
problem, as we setup the fck later when configuring the pixel clocks. Or
this is how it was for omap2, for the rest of the omaps this may not be
so.
For DSI, HDMI and also for DPI when using DSI PLL, we don't need to
change the dss fck, and thus it may be left unconfigured. Usually the
dss fck is already setup fine by default, but we can't trust this.
This patch sets the dss fck to maximum at probe time.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss_calc_clock_rates() was removed earlier as it was not used, but it is
needed for DSI PLL calculations, so this patch adds it back.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit 185bae1095 ("OMAPDSS: DSS: Cleanup
cpu_is_xxxx checks") broke the DSS clocks configuration by erroneously
using the clock parameters applicable to all other OMAP34xx SoCs for the
OMAP363x. This went unnoticed probably because the cpu_is_omap34xx()
class check wasn't seen as matching the OMAP363x subclass.
Fix it by checking for the OMAP363x subclass before checking for the
OMAP34xx class.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The output drivers get the omapdss hw version from the platform data for
their respective output device. This doesn't work with DT, as there's no
platform data for them.
Add a new function, omapdss_get_version(), which returns the dss version
from the core device, which will have platform data on DT also. The
function is exported so that users of omapdss can also use it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When compiling on x86, we get compilation errors for dss.c and dispc.c:
drivers/video/omap2/dss/dispc.c:126:11: error: ‘SZ_4K’ undeclared here
(not in a function)
include <linux/sizes.h> to fix compilation.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The config option CONFIG_OMAP2_DSS_DEBUG_SUPPORT has been removed and replaced
with CONFIG_OMAP2_DSS_DEBUG and CONFIG_OMAP2_DSS_DEBUGFS. CONFIG_OMAP2_DSS_DEBUG
enables DEBUG flag and CONFIG_OMAP2_DSS_DEBUGFS enables creation of debugfs for
OMAPDSS. Both the config options are disabled by default and can be enabled
independently of one another as per convenience.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We can select the video source for DPI output as follows:
OMAP2/3: always LCD1
OMAP4: LCD2 or DIGIT
OMAP5: LCD1/LCD2/LCD3/DIGIT
This patch adds support to select the source, and makes dpi.c call the
function to set the source.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: David Anders <x0132446@ti.com>
Move dss_features to the end of dss.c the same way they are in dispc.c,
so that we don't have to declare prototypes for static feat-related
functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
All the cpu_is checks have been moved to dss_init_features function providing a
much more generic and cleaner interface. The OMAP version and revision specific
initializations in various functions are cleaned and the necessary data are
moved to dss_features structure which is local to dss.c.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Functions dss_calc_clock_rates() and dss_get_clock_div() are removed as these
functions have become redundant and no longer used.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The SDI driver currently relies on the omap_dss_device struct to configure the
number of data pairs as specified by the panel. This makes the SDI interface
driver dependent on the omap_dss_device struct.
Make the SDI driver data maintain it's own data lines field. A panel driver
is expected to call omapdss_sdi_set_datapairs() before enabling the interface.
Even though we configure the number of data pairs here, this function would be
finally mapped to a generic interface op called set_data_lines. The datapairs
argument type has been changed from u8 to int at some places to be in sync with
the 'set_data_lines' ops of other interfaces.
Signed-off-by: Archit Taneja <archit@ti.com>
DSS code wrongly assumes that VENC is always available as source for the external
sync signal for the display controller DIGIT channel. One cannot blindly write/read
the value of DSS_CONTROL[15] as in certain processors (e.g., OMAP5) this operation
may not be valid. If the the sync source is not read correctly, the callers of
dss_get_hdmi_venc_clk_source might make wrong assumptions about, for instance,
video timings.
Logic is added to correctly get the sync signal based on the available displays
in the DIGIT channel. The source is set only if both VENC and HDMI are supported.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove clock constraints related to passive matrix displays.
There is a constraint (pcd_min should be 3) for passive matrix displays. Remove
this constraint in clock divider calculations as we won't support passive
matrix displays any more.
This cleans up the functions which calculate the clock dividers with DSI's PLL
or DSS_FCLK as the clock source.
Signed-off-by: Archit Taneja <archit@ti.com>
The support for LCD3 manager has been added into the manager module. LCD3 panel
has registers as DISPC_CONTROL3 and DISPC_CONFIG3 just like those in LCD and
LCD2 panels. These registers control the Display Controller (DISPC) module for
LCD3 output. The three LCDs support Display Serial Interface (DSI), Remote Frame
Buffer Interface (RFBI) and Parallel CMOS Output Interface (DPI). These LCDs can
be connected through parallel output interface using DISPC and RFBI or DPI. For
serial interface DSS uses DSI.
The LCD3 panel, just like LCD and LCD2 panels, has a clock switch in DSS_CTRL
register which has been enabled. The clock switch chooses between DSS_CLK and
DPLL_DSI1_C_CLK1 as source for LCD3_CLK. New IRQs as DISPC_IRQ_VSYNC3,
DISPC_IRQ_FRAMEDONE3, DISPC_IRQ_ACBIAS_COUNT_STAT3 and DISPC_IRQ_SYNC_LOST3 have
been added specific to the new manager.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If runtime PM is not enabled in the kernel config, pm_runtime_get_sync()
will always return 1 and pm_runtime_put_sync() will always return
-ENOSYS. pm_runtime_get_sync() returning 1 presents no problem to the
driver, but -ENOSYS from pm_runtime_put_sync() causes the driver to
print a warning.
One option would be to ignore errors returned by pm_runtime_put_sync()
totally, as they only say that the call was unable to put the hardware
into suspend mode.
However, I chose to ignore the returned -ENOSYS explicitly, and print a
warning for other errors, as I think we should get notified if the HW
failed to go to suspend properly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Grazvydas Ignotas <notasas@gmail.com>
pm_runtime_put_sync() in dss_runtime_put() returns -EBUSY when any child
of dss is still enabled. This happens, for example, when a display
output is enabled and one dumps the clocks via debugfs. This causes
dss_runtime_get & put to be called.
While I couldn't find anything about this in the documentation and it
wasn't immediately clear from runtime_pm code, it looks to me that
pm_runtime_put_sync() returns -EBUSY to inform that things went fine,
but the device could not be turned off as there are still child devices
that are enabled. This is not a problem.
This patch skips the WARN_ON if pm_runtime_put_sync() returns -EBUSY.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If CONFIG_BUG is not enabled, BUG() does not stop the execution. Many
places in code expect the execution to stop, and this causes compiler
warnings about uninitialized variables and returning from a non-void
function without a return value.
This patch fixes the warnings by initializing the variables and
returning properly after BUG() lines. However, the behaviour is still
undefined after the BUG, but this is the choice the user makes when
using CONFIG_BUG=n.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of having an ugly #ifdef mess in the core.c for creating debugfs
files, add a dss_debugfs_create_file() function that the dss drivers
can use to create the debugfs files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that the omapdss_core device is the parent for all other dss
devices, we don't need to use the dss_runtime_get/put anymore. Instead,
enabling omapdss_core will happen automatically when a child device is
enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We currently have separate device/driver for each DSS HW module. The DPI
and SDI outputs are more or less parts of the DSS or DISPC hardware
modules, but in SW it makes sense to represent them as device/driver
pairs similarly to all the other outputs. This also makes sense for
device tree, as each node under dss will be a platform device, and
handling DPI & SDI somehow differently than the rest would just make the
code more complex.
This patch modifies the dpi.c and sdi.c to create drivers for the
platform devices.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The platform devices for omapdss, dss and dispc drivers are always
present, so we can use platform_driver_probe instead of
platform_driver_register.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For unknown reasons we seem to have a return in each of the omapdss's
uninit functions, which is a void function.
Remove the returns.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The wrong bit field was being updated in DSS_CTRL when trying to configure the
clock source of DSI2 functional clock. Use the correct bit field based on the
dsi module number.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Most of the DSS clocks have restrictions on their frequency based on the
OPP in use. For example, maximum frequency for a clock may be 180MHz in
OPP100, but 90MHz in OPP50. This means that when a high enough pixel
clock or function clock is required, we need to use OPP100.
However, there's currently no way in the PM framework to make that kind
of request. The closest we get is to ask for very high bus throughput
from the PM framework, which should effectively force OPP100.
This patch is a simple version for handling the problem. Instead of
asking for OPP100 only when needed, this patch asks for OPP100 whenever
DSS is active. This obviously is not an optimal solution for cases with
small displays where OPP50 would work just fine. However, a proper
solution is a complex one, and this patch is a short term solution for
the problem.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=o5Xl
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: global cleanups" from Arnd Bergmann:
"Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up trivial conflicts mainly due to #include's being changes on
both sides.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits)
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
PM / devfreq: update the name of EXYNOS clock registers that were omitted
PM / devfreq: update the name of EXYNOS clock register
ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
ARM: EXYNOS: use static declaration on regarding clock
ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
ARM: OMAP2+: Fix build error after merge
ARM: S3C24XX: remove call to s3c24xx_setup_clocks
...
This is needed to minimize io.h so the SoC specific io.h
for ARMs can removed.
Note that minimal driver changes for DSS and RNG are needed to
include cpu.h for SoC detection macros.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that dss is using devm_ functions for allocation in probe functions,
small reordering of the allocations allows us to clean up the probe
functions more.
This patch moves "unmanaged" allocations after the managed ones, and
uses plain returns instead of gotos where possible. This lets us remove
a bunch of goto labels, simplifying the probe's error handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdss doesn't work properly on system suspend. The problem seems to be
the fact that omapdss uses pm_runtime_put() functions when turning off
the hardware, and when system suspend is in process only sync versions
are allowed.
Using non-sync versions normally and sync versions when suspending would
need rather ugly hacks to convey the information of
suspending/not-suspending to different functions. Optimally the driver
wouldn't even need to care about this, and the PM layer would handle
syncing when suspend is in process.
This patch changes all omapdss's pm_runtime_put calls to
pm_runtime_put_sync. This fixes the suspend problem, and probably the
performance penalty of always using sync versions is negligible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Add dss_get_hdmi_venc_clk_source(), which can be used to get the value
programmed with dss_select_hdmi_venc_clk_source(). This can be used to
find out if the digit output is going to VENC or HDMI.
For OMAP2/3 dss_get_hdmi_venc_clk_source() always returns
DSS_VENC_TV_CLK.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tomi Valkeinen