ACPI specification knows two types of GPIOs: GpioIo and GpioInt. The latter
is used to describe that a given device interrupt line is connected to a
specific GPIO pin. Typical ACPI _CRS entry for such device looks like
below:
Name (_CRS, ResourceTemplate ()
{
I2cSerialBus (0x004A, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.PCI0.I2C6",
0x00, ResourceConsumer)
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000,
IoRestrictionOutputOnly, "\\_SB.GPO0",
0x00, ResourceConsumer)
{
0x004B
}
GpioInt (Level, ActiveLow, Shared, PullDefault, 0x0000,
"\\_SB.GPO0", 0x00, ResourceConsumer)
{
0x004C
}
})
Currently drivers need to request a GPIO corresponding to the right GpioInt
and then translate that to Linux IRQ number. This adds unnecessary lines of
boiler-plate code.
We can ease this a bit by introducing acpi_dev_gpio_irq_get() analogous to
of_irq_get(). This function translates given GpioInt resource under the
device in question to the suitable Linux IRQ number.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The signed error will be wrongly used as valid gpio offset
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
- A new GPIO hogging mechanism has been added. This can
be used on boards that want to drive some GPIO line high,
low, or set it as input on boot and then never touch it
again. For some embedded systems this is bliss and
simplifies things to a great extent.
- Some API cleanup and closure: gpiod_get_array() and
gpiod_put_array() has been added to get and put GPIOs
in bulk as was possible with the non-descriptor API.
- Encapsulate cross-calls to the pin control subsystem in
<linux/gpio/driver.h>. Now this should be the only header
any GPIO driver needs to include or something is wrong.
Cleanups restricting drivers to this include are welcomed
if tested.
- Sort the GPIO Kconfig and split it into submenus, as
it was becoming and unstructured, illogical and
unnavigatable mess. I hope this is easier to follow.
Menus that require a certain subsystem like I2C can
now be hidden nicely for example, still working on
others.
- New drivers:
- New driver for the Altera Soft GPIO.
- The F7188x driver now handles the F71869 and
F71869A variants.
- The MIPS Loongson driver has been moved to
drivers/gpio for consolidation and cleanup.
- Cleanups:
- The MAX732x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- The PCF857x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- Radical cleanup of the OMAP driver.
- Misc:
- Enable the DWAPB GPIO for all architectures. This is
a "hard IP" block from Synopsys which has started to
turn up in so diverse architectures as X86 Quark, ARC
and a slew of ARM systems. So even though it's not an
expander, it's generic enough to be available for all.
- We add a mock GPIO on Crystalcove PMIC after a long
discussion with Daniel Vetter et al, tracing back to
the shootout at the kernel summit where DRM drivers
and sub-componentization was discussed. In this case
a mock GPIO is assumed to be the best compromise
gaining some reuse of infrastructure without making
DRM drivers overly complex at the same time. Let's
see.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVMNYHAAoJEEEQszewGV1zSmwP/2oCk4CB4fexrqM+irUJrDnT
3D/8tuaq7EghMnwPXCfHa8R8eWF6XEDvHPcJNVgXiWbtCGRMpdsiobFunzwLQv5A
CbcuAOzWmzA0ePbfa0+xpLpWM/RJP9u1an/RboIzeeS7oQ1Yj/VjF8uS8Se+Pe3r
nPKvTpoU5lGpIUTEEYjiJhL8pBmp8k75a6NGM4U8VwXI9BsdhDkpRGsfG3NK8hs2
vSvWDB19NCW6iOd3gN4KA4f0Zz57WONMS7jY2WaipqYRlr37o4i2CA0ME1xoXEfg
3JT1lmg7esNCvnjQOaGTaM6nf66j7/nleNtnMmAAJcJeMNoh9yS6397TGaYFThsn
C1WmAoaonor3RAujrL3oRenxfq2+Vl63OvsClDiWz7LL9YYJ/G2nS3MggFHpZUhu
/CHXSt08j0Kewfc5SkvFCTnrPG7aWy/YDou6PfuXIvkFp5h1FXDkHTXvOD33turD
ohEPlg/9i2uCnVQfN+GV4h69WSyEiOpxG5W7ryE+nIo6XzWIctHLIH2V6aE7YrwG
FBg7hC1QV1cI776HFOuM4rPwG1N80IQeC3vr5z/jEtZVPXrIaGvupxFC+O1DAx4W
rzBD8lX45B96WmIW2odg11KXXyPO1srW4ZFWghm95HTfvnQc3O6LmV9riv1k7DYA
gR+aRYNiLO01UmoTPYbK
=QFbC
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.1 development cycle:
- A new GPIO hogging mechanism has been added. This can be used on
boards that want to drive some GPIO line high, low, or set it as
input on boot and then never touch it again. For some embedded
systems this is bliss and simplifies things to a great extent.
- Some API cleanup and closure: gpiod_get_array() and
gpiod_put_array() has been added to get and put GPIOs in bulk as
was possible with the non-descriptor API.
- Encapsulate cross-calls to the pin control subsystem in
<linux/gpio/driver.h>. Now this should be the only header any GPIO
driver needs to include or something is wrong. Cleanups
restricting drivers to this include are welcomed if tested.
- Sort the GPIO Kconfig and split it into submenus, as it was
becoming and unstructured, illogical and unnavigatable mess. I
hope this is easier to follow. Menus that require a certain
subsystem like I2C can now be hidden nicely for example, still
working on others.
- New drivers:
- New driver for the Altera Soft GPIO.
- The F7188x driver now handles the F71869 and F71869A variants.
- The MIPS Loongson driver has been moved to drivers/gpio for
consolidation and cleanup.
- Cleanups:
- The MAX732x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- The PCF857x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- Radical cleanup of the OMAP driver.
- Misc:
- Enable the DWAPB GPIO for all architectures. This is a "hard
IP" block from Synopsys which has started to turn up in so
diverse architectures as X86 Quark, ARC and a slew of ARM
systems. So even though it's not an expander, it's generic
enough to be available for all.
- We add a mock GPIO on Crystalcove PMIC after a long discussion
with Daniel Vetter et al, tracing back to the shootout at the
kernel summit where DRM drivers and sub-componentization was
discussed. In this case a mock GPIO is assumed to be the best
compromise gaining some reuse of infrastructure without making
DRM drivers overly complex at the same time. Let's see"
* tag 'gpio-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (62 commits)
Revert "gpio: sch: use uapi/linux/pci_ids.h directly"
gpio: dwapb: remove dependencies
gpio: dwapb: enable for ARC
gpio: removing kfree remove functionality
gpio: mvebu: Fix mask/unmask managment per irq chip type
gpio: split GPIO drivers in submenus
gpio: move MFD GPIO drivers under their own comment
gpio: move BCM Kona Kconfig option
gpio: arrange SPI Kconfig symbols alphabetically
gpio: arrange PCI GPIO controllers alphabetically
gpio: arrange I2C Kconfig symbols alphabetically
gpio: arrange Kconfig symbols alphabetically
gpio: ich: Implement get_direction function
gpio: use (!foo) instead of (foo == NULL)
gpio: arizona: drop owner assignment from platform_drivers
gpio: max7300: remove 'ret' variable
gpio: use devm_kzalloc
gpio: sch: use uapi/linux/pci_ids.h directly
gpio: x-gene: fix devm_ioremap_resource() check
gpio: loongson: Add Loongson-3A/3B GPIO driver support
...
In acpi_gpiochip_request_interrupts() the handle local
variable already contains the value that we want to pass
to acpi_walk_resources(), so it is better to use that
variable instead of evaluating ACPI_HANDLE() once more
for the same device.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If GPIO driver use pin mapping, need to translate pin number
between ACPI table and GPIO driver.
This issue is found on one platform with Cherryview gpio
controller, kernel is hang when executed _PS0 method of
one ACPI device, since without this translation, it access
invalid gpiodesc array.
Verified it works again with this patch.
Signed-off-by: qipeng.zha <qipeng.zha@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce new functions for conveniently obtaining and disposing of
an entire array of GPIOs with one function call.
ACPI parts tested by Mika Westerberg, DT parts tested by Rojhalat
Ibrahim.
Change log:
v5: move the ACPI functions to gpiolib-acpi.c
v4: - use shorter names for members of struct gpio_descs
- rename lut_gpio_count to platform_gpio_count for clarity
- add check for successful memory allocation
- use ERR_CAST()
v3: - rebase on current linux-gpio devel branch
- fix ACPI GPIO counting
- allow for zero-sized arrays
- make the flags argument mandatory for the new functions
- clarify documentation
v2: change interface
Suggested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- A new API that allows setting more than one GPIO at the
time. This is implemented for the new descriptor-based
API only and makes it possible to e.g. toggle a clock and
data line at the same time, if the hardware can do this
with a single register write. Both consumers and drivers
need new calls, and the core will fall back to driving
individual lines where needed. Implemented for the MPC8xxx
driver initially.
- Patched the mdio-mux-gpio and the serial mctrl driver
that drives modems to use the new multiple-setting API
to set several signals simultaneously.
- Get rid of the global GPIO descriptor array, and instead
allocate descriptors dynamically for each GPIO on a certain
GPIO chip. This moves us closer to getting rid of the
limitation of using the global, static GPIO numberspace.
- New driver and device tree bindings for 74xx ICs.
- New driver and device tree bindings for the VF610 Vybrid.
- Support the RCAR r8a7793 and r8a7794.
- Guidelines for GPIO device tree bindings trying to get
things a bit more strict with the advent of combined
device properties.
- Suspend/resume support for the MVEBU driver.
- A slew of minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZAhA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull take two of the GPIO updates:
"Same stuff as last time, now with a fixup patch for the previous
compile error plus I ran a few extra rounds of compile-testing.
This is the bulk of GPIO changes for the v3.19 series:
- A new API that allows setting more than one GPIO at the time. This
is implemented for the new descriptor-based API only and makes it
possible to e.g. toggle a clock and data line at the same time, if
the hardware can do this with a single register write. Both
consumers and drivers need new calls, and the core will fall back
to driving individual lines where needed. Implemented for the
MPC8xxx driver initially
- Patched the mdio-mux-gpio and the serial mctrl driver that drives
modems to use the new multiple-setting API to set several signals
simultaneously
- Get rid of the global GPIO descriptor array, and instead allocate
descriptors dynamically for each GPIO on a certain GPIO chip. This
moves us closer to getting rid of the limitation of using the
global, static GPIO numberspace
- New driver and device tree bindings for 74xx ICs
- New driver and device tree bindings for the VF610 Vybrid
- Support the RCAR r8a7793 and r8a7794
- Guidelines for GPIO device tree bindings trying to get things a bit
more strict with the advent of combined device properties
- Suspend/resume support for the MVEBU driver
- A slew of minor fixes and improvements"
* tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (33 commits)
gpio: mcp23s08: fix up compilation error
gpio: pl061: document gpio-ranges property for bindings file
gpio: pl061: hook request if gpio-ranges avaiable
gpio: mcp23s08: Add option to configure IRQ output polarity as active high
gpio: fix deferred probe detection for legacy API
serial: mctrl_gpio: use gpiod_set_array function
mdio-mux-gpio: Use GPIO descriptor interface and new gpiod_set_array function
gpio: remove const modifier from gpiod_get_direction()
gpio: remove gpio_descs global array
gpio: mxs: implement get_direction callback
gpio: em: Use dynamic allocation of GPIOs
gpio: Check if base is positive before calling gpio_is_valid()
gpio: mcp23s08: Add simple IRQ support for SPI devices
gpio: mcp23s08: request a shared interrupt
gpio: mcp23s08: Do not free unrequested interrupt
gpio: rcar: Add r8a7793 and r8a7794 support
gpio-mpc8xxx: add mpc8xxx_gpio_set_multiple function
gpiolib: allow simultaneous setting of multiple GPIO outputs
gpio: mvebu: add suspend/resume support
gpio: gpio-davinci: remove duplicate check on resource
..
- Force conversion of the ux500 pin control device trees
and parsers to use the generic pin control bindings.
- New driver and device tree bindings for the Qualcomm
PMIC MPP pin controller and GPIO.
- Some ACPI infrastructure for pin controllers.
- New driver for the Intel CherryView/Braswell pin controller,
the first Intel pin controller to fully take advantage of
the pin control subsystem.
- Support the Freescale i.MX VF610 variant.
- Support the sunxi A80 variant.
- Support the Samsung Exynos 4415 and Exynos 7 variants.
- Split out Intel pin controllers to their own subdirectory.
- A large slew of rockchip pin control updates, including
suspend/resume support.
- A large slew of Samsung Exynos pin controller updates.
- Various minor updates and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sxpe
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
"Here is a stash of pin control changes I have collected for the v3.19
series. Mainly new hardware support, with Intels new embedded SoC as
the especially interesting thing standing out, fully using the
subsystem.
- Force conversion of the ux500 pin control device trees and parsers
to use the generic pin control bindings.
- New driver and device tree bindings for the Qualcomm PMIC MPP pin
controller and GPIO.
- Some ACPI infrastructure for pin controllers.
- New driver for the Intel CherryView/Braswell pin controller, the
first Intel pin controller to fully take advantage of the pin
control subsystem.
- Support the Freescale i.MX VF610 variant.
- Support the sunxi A80 variant.
- Support the Samsung Exynos 4415 and Exynos 7 variants.
- Split out Intel pin controllers to their own subdirectory.
- A large slew of rockchip pin control updates, including
suspend/resume support.
- A large slew of Samsung Exynos pin controller updates.
- Various minor updates and fixes"
* tag 'pinctrl-v3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (49 commits)
pinctrl: at91: enhance (debugfs) at91_gpio_dbg_show
pinctrl: meson: add device tree bindings documentation
gpio: tz1090: Fix error handling of irq_of_parse_and_map
pinctrl: tz1090-pinctrl.txt: Fix typo in binding
pinctrl: pinconf-generic: Declare dt_params/conf_items const
pinctrl: exynos: Add support for Exynos4415
pinctrl: exynos: Add initial driver data for Exynos7
pinctrl: exynos: Add irq_chip instance for Exynos7 wakeup interrupts
pinctrl: exynos: Consolidate irq domain callbacks
pinctrl: exynos: Generalize the eint16_31 demux code
pinctrl: samsung: Separate per-bank init and runtime data
pinctrl: samsung: Constify samsung_pin_ctrl struct
pinctrl: samsung: Constify samsung_pin_bank_type struct
pinctrl: samsung: Drop unused label field in samsung_pin_ctrl struct
pinctrl: samsung: Make samsung_pinctrl_get_soc_data use ERR_PTR()
pinctrl: Add Intel Cherryview/Braswell pin controller support
gpio / ACPI: Add knowledge about pin controllers to acpi_get_gpiod()
pinctrl: Fix path error in documentation
pinctrl: rockchip: save and restore gpio6_c6 pinmux in suspend/resume
pinctrl: rockchip: add suspend/resume functions
...
The size_prop argument of the recently added function
acpi_dev_get_property_reference() is not used by the only current
caller of that function and is very unlikely to be used at any time
going forward.
Namely, for a property whose value is a list of items each containing
a references to a device object possibly accompanied by some integers,
the number of items in the list can always be computed as the number
of elements of type ACPI_TYPE_LOCAL_REFERENCE in the property package.
Thus it should never be necessary to provide an additional "cells"
property with a value equal to the number of items in that list. It
also should never be necessary to provide a "cells" property specifying
how many integers are supposed to be following each reference.
For this reason, drop the size_prop argument from
acpi_dev_get_property_reference() and update its caller accordingly.
Link: http://marc.info/?l=linux-kernel&m=141511255610556&w=2
Suggested-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Provide a way for device drivers using GPIOs described by ACPI
GpioIo resources in _CRS to tell the GPIO subsystem what names
(connection IDs) to associate with specific GPIO pins defined
in there.
To do that, a driver needs to define a mapping table as a
NULL-terminated array of struct acpi_gpio_mapping objects
that each contain a name, a pointer to an array of line data
(struct acpi_gpio_params) objects and the size of that array.
Each struct acpi_gpio_params object consists of three fields,
crs_entry_index, line_index, active_low, representing the index of
the target GpioIo()/GpioInt() resource in _CRS starting from zero,
the index of the target line in that resource starting from zero,
and the active-low flag for that line, respectively.
Next, the mapping table needs to be passed as the second
argument to acpi_dev_add_driver_gpios() that will register it with
the ACPI device object pointed to by its first argument. That
should be done in the driver's .probe() routine.
On removal, the driver should unregister its GPIO mapping table
by calling acpi_dev_remove_driver_gpios() on the ACPI device
object where that table was previously registered.
Included are fixes from Mika Westerberg.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With release of ACPI 5.1 and _DSD method we can finally name GPIOs (and
other things as well) returned by _CRS. Previously we were only able to
use integer index to find the corresponding GPIO, which is pretty error
prone if the order changes.
With _DSD we can now query GPIOs using name instead of an integer index,
like the below example shows:
// Bluetooth device with reset and shutdown GPIOs
Device (BTH)
{
Name (_HID, ...)
Name (_CRS, ResourceTemplate ()
{
GpioIo (Exclusive, PullUp, 0, 0, IoRestrictionInputOnly,
"\\_SB.GPO0", 0, ResourceConsumer) {15}
GpioIo (Exclusive, PullUp, 0, 0, IoRestrictionInputOnly,
"\\_SB.GPO0", 0, ResourceConsumer) {27, 31}
})
Name (_DSD, Package ()
{
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package () {"reset-gpio", Package() {^BTH, 1, 1, 0 }},
Package () {"shutdown-gpio", Package() {^BTH, 0, 0, 0 }},
}
})
}
The format of the supported GPIO property is:
Package () { "name", Package () { ref, index, pin, active_low }}
ref - The device that has _CRS containing GpioIo()/GpioInt() resources,
typically this is the device itself (BTH in our case).
index - Index of the GpioIo()/GpioInt() resource in _CRS starting from zero.
pin - Pin in the GpioIo()/GpioInt() resource. Typically this is zero.
active_low - If 1 the GPIO is marked as active_low.
Since ACPI GpioIo() resource does not have field saying whether it is
active low or high, the "active_low" argument can be used here. Setting
it to 1 marks the GPIO as active low.
In our Bluetooth example the "reset-gpio" refers to the second GpioIo()
resource, second pin in that resource with the GPIO number of 31.
This patch implements necessary support to gpiolib for extracting GPIOs
using _DSD device properties.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The GPIO resources (GpioIo/GpioInt) used in ACPI contain a GPIO number
which is relative to the hardware GPIO controller. Typically this number
can be translated directly to Linux GPIO number because the mapping is
pretty much 1:1.
However, when the GPIO driver is using pins exported by a pin controller
driver via set of GPIO ranges, the mapping might not be 1:1 anymore and
direct translation does not work.
In such cases we need to translate the ACPI GPIO number to be suitable for
the GPIO controller driver in question by checking all the pin controller
GPIO ranges under the given device and using those to get the proper GPIO
number.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This function actually operates on a gpio_chip, so its prefix should
reflect that fact for consistency with other functions defined in
gpio/driver.h.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This
was done to avoid having a custom <asm/gpio.h> header for
the x86 architecture - GPIO is custom and complicated
enough as it is already! We want to move to a radix to
store the descriptors going forward, and finally get rid
of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated
by Abdoulaye Berthe. It is not accepted by the system that
the removal of a GPIO chip fails during e.g. reboot or
shutdown, and therefore the return value has now painfully
been refactored away. For special cases like GPIO expanders
on a hot-pluggable bus like USB, we may later add some
gpiochip_try_remove() call, but for the cases we have now,
return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI
GPIO library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle
also threaded, nested interrupts and set up the parent IRQ
correctly. Switch STMPE and TC3589x drivers to use this
registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so
that also GPIO expanders that block but are still not
using threaded IRQ handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the
"DSP GPIO" found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated
from and MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08,
DWAPB, OMAP, Xilinx and Crystalcove drivers.
- Various minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8InA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
Fix code when the operation region callback is for an gpio, which
is not at index 0 and for partial pins in a GPIO definition.
For example:
Name (GMOD, ResourceTemplate ()
{
//3 Outputs that define the Power mode of the device
GpioIo (Exclusive, PullDown, , , , "\\_SB.GPI2") {10, 11, 12}
})
}
If opregion callback calls is for:
- Set pin 10, then address = 0 and bit length = 1
- Set pin 11, then address = 1 and bit length = 1
- Set for both pin 11 and pin 12, then address = 1, bit length = 2
This change requires updated ACPICA gpio operation handler code to
send the pin index and bit length.
Fixes: 473ed7be0d (gpio / ACPI: Add support for ACPI GPIO operation regions)
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+: 75ec6e55f1 ACPICA: Update to GPIO region handler interface.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The current prototype of gpiochip_request_own_desc() requires to obtain
a pointer to a descriptor. This is in contradiction to all other GPIO
request schemes, and imposes an extra step of obtaining a descriptor to
drivers. Most drivers actually cannot even perform that step since the
function that does it (gpichip_get_desc()) is gpiolib-private.
Change gpiochip_request_own_desc() to return a descriptor from a
(chip, hwnum) tuple and update users of this function (currently
gpiolib-acpi only).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO descriptors are changing from unique and permanent tokens to
allocated resources. Therefore gpiochip_get_desc() cannot be used as a
way to obtain a global GPIO descriptor anymore.
This patch updates the gpiolib ACPI support code to keep and use the
descriptor returned by a centralized call to gpiochip_get_desc().
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since now we have irqchip helpers that the GPIO chip drivers are supposed
to use if possible, we can move the registration of ACPI events to happen
in these helpers. This seems to be more natural place and might encourage
GPIO chip driver writers to take advantage of the irqchip helpers.
We make the functions available to GPIO chip drivers via private gpiolib.h,
just in case generic irqchip helpers are not suitable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio_lock/unlock_as_irq() are working with (chip, offset) arguments and
are thus not using the old integer namespace. Therefore, there is no
reason to have gpiod variants of these functions working with
descriptors, especially since the (chip, offset) tuple is more suitable
to the users of these functions (GPIO drivers, whereas GPIO descriptors
are targeted at GPIO consumers).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO operation region handler should be called where sleep is
allowed, so we should use the *_cansleep version of gpiod_get/set APIs
or we will get a warning message complaining invalid context if the GPIO
chip has the cansleep flag set.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Dan Carpenter's static code checker reports:
The patch 473ed7be0da0: "gpio / ACPI: Add support for ACPI GPIO
operation regions" from Mar 14, 2014, leads to the following static
checker warning:
drivers/gpio/gpiolib-acpi.c:454 acpi_gpio_adr_space_handler()
warn: should 'gpiod_get_raw_value(desc) << i' be a 64 bit type?
This is due the fact that *value is of type u64 and gpiod_get_raw_value()
returns int. Since i can be larger than 31, it is possible that the value
returned gets wrapped.
Fix this by casting the return of gpiod_get_raw_value() to u64 first before
shift.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO operation regions is a new feature introduced in ACPI 5.0
specification. This feature adds a way for platform ASL code to call back
to OS GPIO driver and toggle GPIO pins.
An example ASL code from Lenovo Miix 2 tablet with only relevant part
listed:
Device (\_SB.GPO0)
{
Name (AVBL, Zero)
Method (_REG, 2, NotSerialized)
{
If (LEqual (Arg0, 0x08))
{
// Marks the region available
Store (Arg1, AVBL)
}
}
OperationRegion (GPOP, GeneralPurposeIo, Zero, 0x0C)
Field (GPOP, ByteAcc, NoLock, Preserve)
{
Connection (
GpioIo (Exclusive, PullDefault, 0, 0, IoRestrictionOutputOnly,
"\\_SB.GPO0", 0x00, ResourceConsumer,,)
{
0x003B
}
),
SHD3, 1,
}
}
Device (SHUB)
{
Method (_PS0, 0, Serialized)
{
If (LEqual (\_SB.GPO0.AVBL, One))
{
Store (One, \_SB.GPO0.SHD3)
Sleep (0x32)
}
}
Method (_PS3, 0, Serialized)
{
If (LEqual (\_SB.GPO0.AVBL, One))
{
Store (Zero, \_SB.GPO0.SHD3)
}
}
}
How this works is that whenever _PS0 or _PS3 method is run (typically when
SHUB device is transitioned to D0 or D3 respectively), ASL code checks if
the GPIO operation region is available (\_SB.GPO0.AVBL). If it is we go and
store either 0 or 1 to \_SB.GPO0.SHD3.
Now, when ACPICA notices ACPI GPIO operation region access (the store
above) it will call acpi_gpio_adr_space_handler() that then toggles the
GPIO accordingly using standard gpiolib interfaces.
Implement the support by registering GPIO operation region handlers for all
GPIO devices that have an ACPI handle. First time the GPIO is used by the
ASL code we make sure that the GPIO stays requested until the GPIO chip
driver itself is unloaded. If we find out that the GPIO is already
requested we just toggle it according to the value got from ASL code.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current ACPI GPIO event handling code was never tested against real
hardware with functioning GPIO triggered events (at the time such hardware
wasn't available). Thus it misses certain things like requesting the GPIOs
properly, passing correct flags to the interrupt handler and so on.
This patch reworks ACPI GPIO event handling so that we:
1) Use struct acpi_gpio_event for all GPIO signaled events.
2) Switch to use GPIO descriptor API and request GPIOs by calling
gpiochip_request_own_desc() that we added in a previous patch.
3) Pass proper flags from ACPI GPIO resource to request_threaded_irq().
Also instead of open-coding the _AEI iteration loop we can use
acpi_walk_resources(). This simplifies the code a bit and fixes memory leak
that was caused by missing kfree() for buffer returned by
acpi_get_event_resources().
Since the remove path now calls gpiochip_free_own_desc() which takes GPIO
spinlock we need to call acpi_gpiochip_remove() outside of that lock
(analogous to acpi_gpiochip_add() path where the lock is released before
those funtions are called).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to consolidate _Exx, _Lxx and _EVT to use the same structure make
the structure name to reflect that we are dealing with any event, not just
_EVT.
This is just rename, no functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We are going to add more ACPI specific data to accompany GPIO chip so
instead of allocating it per each use-case we allocate it once when
acpi_gpiochip_add() is called and release it when acpi_gpiochip_remove() is
called.
Doing this allows us to add more ACPI specific data by merely adding new
fields to struct acpi_gpio_chip.
In addition we embed evt_pins member directly to the structure instead of
having it as a pointer. This simplifies the code a bit since we don't need
to check against NULL.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio_to_desc() must die. Replace one of its usage by the
newly-introduced gpiochip_get_desc() function.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that all users of acpi_gpio.h have been moved to use either the GPIO
descriptor interface or to the internal gpiolib.h we can get rid of
acpi_gpio.h entirely.
Once this is done the only interface to get GPIOs to drivers enumerated
from ACPI namespace is the descriptor based interface.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of asking each driver to register to ACPI events we can just call
acpi_gpiochip_register_interrupts() for each chip that has an ACPI handle.
The function checks chip->to_irq and if it is set to NULL (a GPIO driver
that doesn't do interrupts) the function does nothing.
We also add the a new header drivers/gpio/gpiolib.h that is used for
functions internal to gpiolib and add ACPI GPIO chip registering functions
to that header.
Once that is done we can remove call to acpi_gpiochip_register_interrupts()
from its only user, pinctrl-baytrail.c
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Doing this allows drivers to distinguish between a real error case (if
there was an error when we tried to resolve the GPIO) and when the optional
GPIO line was not available.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACPI GpioInt resources contain polarity field that is used to specify
whether the interrupt is active high or low. Since gpiolib supports
GPIOF_ACTIVE_LOW we can pass this information in the flags field in
acpi_find_gpio(), analogous to the DeviceTree version.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new GPIO descriptor based interface is now preferred over the old
integer based one. This patch converts the ACPI GPIO helpers to use this
new interface internally. In addition to that provide compatibility
function acpi_get_gpio_by_index() that converts the returned GPIO
descriptor to an integer.
We also drop acpi_get_gpio() as it is not used anywhere outside
gpiolib-acpi and even there we use acpi_get_gpiod() instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It makes more sense to have these functions close to each other. No
functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
acpi_execute_simple_method() is a new ACPI API introduced to invoke
an ACPI control method that has single integer parameter and no return value.
Convert acpi_evaluate_object() to acpi_execute_simple_method()
in drivers/gpio/gpiolib-acpi.c
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of open-coding ACPI GPIO resource lookup in each driver, we provide
a helper function analogous to Device Tree version that allows drivers to
specify which GPIO resource they are interested (using an index to the GPIO
resources). The function then finds out the correct resource, translates
the ACPI GPIO number to the corresponding Linux GPIO number and returns
that.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 0d1c28a (gpiolib-acpi: Add ACPI5 event model support to gpio.)
that added support for ACPI events signalled through GPIO interrupts
covered only GPIO pins whose numbers are less than or equal to 255.
However, there may be GPIO pins with numbers greater than 255 and
the ACPI spec (ACPI 5.0, Section 5.6.5.1) requires the _EVT method
to be used for handling events corresponding to those pins.
Moreover, according to the spec, _EVT is the default mechanism
for handling all ACPI events signalled through GPIO interrupts,
so if the _Exx/_Lxx method is not present for the given pin,
_EVT should be used instead. If present, though, _Exx/_Lxx take
precedence over _EVT which shouldn't be executed in that case
(ACPI 5.0, Section 5.6.5.3).
Modify acpi_gpiochip_request_interrupts() to follow the spec as
described above and add acpi_gpiochip_free_interrupts() needed
to free interrupts associated with _EVT.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Print error message if requesting an interrupt fails.
Use int instead of unsigned for interrupts in case of error values
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add ability to handle ACPI events signalled by GPIO interrupts.
ACPI5 platforms can use GPIO signaled ACPI events. These GPIO interrupts are
handled by ACPI event methods which need to be called from the GPIO
controller's interrupt handler. acpi_gpio_request_interrupt() finds out which
gpio pins have acpi event methods and assigns interrupt handlers that calls
the acpi event methods for those pins.
Partially based on work by Rui Zhang <rui.zhang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for translating ACPI GPIO pin numbers to Linux GPIO API pins.
Needs a gpio controller driver with the acpi handler hook set.
Drivers can use acpi_get_gpio() to translate ACPI5 GpioIO and GpioInt
resources to Linux GPIO's.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Walleij