When the root complex suspends it must send a PME_Turn_Off TLP.
Implement this by asserting the "turnoff" reset.
On imx7d this functionality is part of the System Reset Controller (SRC)
and is exposed through the linux reset-controller subsystem.
On imx6 equivalent bits are in the IOMUXC pinmux controller General
Purpose Register (GPR) area which the imx6-pcie driver accesses
directly.
This is only for imx7d right now but it's deliberately implemented as an
optional reset, ignoring the chip variant:
* Older dtbs won't have this reset so it will be ignored.
* Future chips might also expose this as a reset controller.
For example imx8m (not yet supported) has the exact same
PCIE_CTRL_APPS_TURNOFF bit in the same location.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
On imx7d the pcie-phy power domain is turned off in suspend and this can
make the system hang after resume when attempting any read from PCI.
Fix this by adding minimal suspend/resume code. This will prepare for
powering down on suspend and reset the block on resume.
Code is only for imx7d but a very similar sequence can be used for
other SOCs.
Original-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
[lorenzo.pieralisi@arm.com: commit log update]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
The power up defaults of the MPLL are designed for the standard 125MHz
refclock derived from the ENET PLL. As this clock has a jitter that
violates the PCIe Gen2 timing requirements, some board designs use
an external reference clock generator. Those clock generators may
output a clock at a different rate than what the MPLL expects
(usually a 100MHz clock, to re-use the PCIe bus clock).
In that case the MPLL must be reconfigured via overrides to use
different refclock dividers and loop multipliers. The i.MX6
reference manual lists both 100MHz and 200MHz as supported refclock
rates and the associated mult and div values.
Only the 100MHz setup has been tested on a real board, but since the
200MHz setup only differs in the used pre-divider it seems safe to
add it now.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Function dw_pcie_host_init() already initializes the root_bus_nr field
of 'struct pcie_port', so the -1 assignment prior to calling
dw_pcie_host_init() in platform specific driver is not really needed.
Drop it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Native PCI drivers for root complex devices were originally all in
drivers/pci/host/. Some of these devices can also be operated in endpoint
mode. Drivers for endpoint mode didn't seem to fit in the "host"
directory, so we put both the root complex and endpoint drivers in
per-device directories, e.g., drivers/pci/dwc/, drivers/pci/cadence/, etc.
These per-device directories contain trivial Kconfig and Makefiles and
clutter drivers/pci/. Make a new drivers/pci/controllers/ directory and
collect all the device-specific drivers there.
No functional change intended.
Link: https://lkml.kernel.org/r/1520304202-232891-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Leonard Crestez