Add support for SoCs that need to register core and module clocks early in
order to use OF drivers that exclusively use macros such as
TIMER_OF_DECLARE.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for the R7S9210 (RZ/A2) Clock Pulse Generator and Module
Standby.
The Module Standby HW in the RZ/A series is very close to R-Car HW, except
for how the registers are laid out.
The MSTP registers are only 8-bits wide, there are no status registers
(MSTPSR), and the register offsets are a little different. Since the RZ/A
hardware manuals refer to these registers as the Standby Control Registers,
we'll use that name to distinguish the RZ/A type from the R-Car type.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Rob Herring <robh@kernel.org> # DT bits
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for defining fixed rate clocks, to be used for on-chip
oscillators.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
general cleanups, but nothing too major. The majority of the diff goes to
two SoCs, Actions Semi and Qualcomm. A brand new driver is introduced for
Actions Semi so it takes up some lines to add all the different types, and
the Qualcomm diff is there because we add support for two SoCs and it's quite
a bit of data.
Otherwise the big driver updates are on TI Davinci and Amlogic platforms. And
then the long tail of driver updates for various fixes and stuff follows
after that.
Core:
- debugfs cleanups removing error checking and an unused provider API
- Removal of a clk init typedef that isn't used
- Usage of match_string() to simplify parent string name matching
- OF clk helpers moved to their own file (linux/of_clk.h)
- Make clk warnings more readable across kernel versions
New Drivers:
- Qualcomm SDM845 GCC and Video clk controllers
- Qualcomm MSM8998 GCC
- Actions Semi S900 SoC support
- Nuvoton npcm750 microcontroller clks
- Amlogic axg AO clock controller
Removed Drivers:
- Deprecated Rockchip clk-gate driver
Updates:
- debugfs functions stopped checking return values
- Support for the MSIOF module clocks on Rensas R-Car M3-N
- Support for the new Rensas RZ/G1C and R-Car E3 SoCs
- Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
- Berlin and Amlogic SPDX tagging
- Usage of of_clk_get_parent_count() in more places
- Proper implementation of the CDEV1/2 clocks on Tegra20
- Allwinner H6 PRCM clock support and R40 EMAC support
- Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
- Round closest support for meson's mpll driver
- Support for meson8b nand clocks and gxbb video decoder clocks
- Mediatek mali clks
- STM32MP1 fixes
- Uniphier LD11/LD20 stream demux system clock
-----BEGIN PGP SIGNATURE-----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=KK/v
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time we have a good set of changes to the core framework that do
some general cleanups, but nothing too major. The majority of the diff
goes to two SoCs, Actions Semi and Qualcomm. A brand new driver is
introduced for Actions Semi so it takes up some lines to add all the
different types, and the Qualcomm diff is there because we add support
for two SoCs and it's quite a bit of data.
Otherwise the big driver updates are on TI Davinci and Amlogic
platforms. And then the long tail of driver updates for various fixes
and stuff follows after that.
Core:
- debugfs cleanups removing error checking and an unused provider API
- Removal of a clk init typedef that isn't used
- Usage of match_string() to simplify parent string name matching
- OF clk helpers moved to their own file (linux/of_clk.h)
- Make clk warnings more readable across kernel versions
New Drivers:
- Qualcomm SDM845 GCC and Video clk controllers
- Qualcomm MSM8998 GCC
- Actions Semi S900 SoC support
- Nuvoton npcm750 microcontroller clks
- Amlogic axg AO clock controller
Removed Drivers:
- Deprecated Rockchip clk-gate driver
Updates:
- debugfs functions stopped checking return values
- Support for the MSIOF module clocks on Rensas R-Car M3-N
- Support for the new Rensas RZ/G1C and R-Car E3 SoCs
- Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
- Berlin and Amlogic SPDX tagging
- Usage of of_clk_get_parent_count() in more places
- Proper implementation of the CDEV1/2 clocks on Tegra20
- Allwinner H6 PRCM clock support and R40 EMAC support
- Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
- Round closest support for meson's mpll driver
- Support for meson8b nand clocks and gxbb video decoder clocks
- Mediatek mali clks
- STM32MP1 fixes
- Uniphier LD11/LD20 stream demux system clock"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
clk: qcom: Export clk_fabia_pll_configure()
clk: bcm: Update and add Stingray clock entries
dt-bindings: clk: Update Stingray binding doc
clk-si544: Properly round requested frequency to nearest match
clk: ingenic: jz4770: Add 150us delay after enabling VPU clock
clk: ingenic: jz4770: Enable power of AHB1 bus after ungating VPU clock
clk: ingenic: jz4770: Modify C1CLK clock to disable CPU clock stop on idle
clk: ingenic: jz4770: Change OTG from custom to standard gated clock
clk: ingenic: Support specifying "wait for clock stable" delay
clk: ingenic: Add support for clocks whose gate bit is inverted
clk: use match_string() helper
clk: bcm2835: use match_string() helper
clk: Return void from debug_init op
clk: remove clk_debugfs_add_file()
clk: tegra: no need to check return value of debugfs_create functions
clk: davinci: no need to check return value of debugfs_create functions
clk: bcm2835: no need to check return value of debugfs_create functions
clk: no need to check return value of debugfs_create functions
clk: imx6: add EPIT clock support
clk: mvebu: use correct bit for 98DX3236 NAND
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=hB2y
-----END PGP SIGNATURE-----
Merge tag 'printk-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk
Pull printk updates from Petr Mladek:
- Help userspace log daemons to catch up with a flood of messages. They
will get woken after each message even if the console is far behind
and handled by another process.
- Flush printk safe buffers safely even when panic() happens in the
normal context.
- Fix possible va_list reuse when race happened in printk_safe().
- Remove %pCr printf format to prevent sleeping in the atomic context.
- Misc vsprintf code cleanup.
* tag 'printk-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
printk: drop in_nmi check from printk_safe_flush_on_panic()
lib/vsprintf: Remove atomic-unsafe support for %pCr
serial: sh-sci: Stop using printk format %pCr
thermal: bcm2835: Stop using printk format %pCr
clk: renesas: cpg-mssr: Stop using printk format %pCr
printk: fix possible reuse of va_list variable
printk: wake up klogd in vprintk_emit
vsprintf: Tweak pF/pf comment
lib/vsprintf: Mark expected switch fall-through
lib/vsprintf: Replace space with '_' before crng is ready
lib/vsprintf: Deduplicate pointer_string()
lib/vsprintf: Move pointer_string() upper
lib/vsprintf: Make flag_spec global
lib/vsprintf: Make strspec global
lib/vsprintf: Make dec_spec global
lib/test_printf: Mark big constant with UL
Printk format "%pCr" will be removed soon, as clk_get_rate() must not be
called in atomic context.
Replace it by open-coding the operation. This is safe here, as the code
runs in task context.
Link: http://lkml.kernel.org/r/1527845302-12159-2-git-send-email-geert+renesas@glider.be
To: Jia-Ju Bai <baijiaju1990@gmail.com>
To: Jonathan Corbet <corbet@lwn.net>
To: Michael Turquette <mturquette@baylibre.com>
To: Stephen Boyd <sboyd@kernel.org>
To: Zhang Rui <rui.zhang@intel.com>
To: Eduardo Valentin <edubezval@gmail.com>
To: Eric Anholt <eric@anholt.net>
To: Stefan Wahren <stefan.wahren@i2se.com>
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-doc@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org # 4.5+
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Initial support for R-Car E3 (r8a77990), including core and module
clocks.
Based on the Table 8.2g of "R-Car Series, 3rd Generation User's Manual:
Hardware ((Rev. 0.80, Oct 31, 2017) with Manual Errata on Feb. 28, 2018".
Inspried by patches by Takeshi Kihara in the BSP.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Adjust the R8A77980-specific #ifdefs to use CLK instead of ARCH
to follow same style as other SoCs.
Fixes: ce15783c51 ("clk: renesas: cpg-mssr: add R8A77980 support")
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Initial support for R-Car M3-N (r8a77965), including core and module
clocks.
Based on Table 8.2d of "R-Car Series, 3rd Generation User's Manual:
Hardware (Rev. 0.80, Oct 31, 2017)".
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add R-Car V3H (R8A77980) Clock Pulse Generator / Module Standby and
Software Reset support, using the CPG/MSSR driver core and the common
R-Car Gen3 code.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
If a device is part of the CPG/MSSR Clock Domain and to be used as a
wakeup source, it must be kept active during system suspend.
Currently this is handled in device-specific drivers by explicitly
increasing the use count of the module clock when the device is
configured as a wakeup source. However, the proper way to prevent the
device from being stopped is to inform this requirement to the genpd
core, by setting the GENPD_FLAG_ACTIVE_WAKEUP flag.
Note that this will only affect devices configured as wakeup sources.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
On R-Car Gen3 systems, PSCI system suspend powers down the SoC, losing
clock configuration. Register an (optional) notifier to restore the
DIV6 clock state during system resume.
As DIV6 clocks can be picky w.r.t. modifying multiple register fields at
once, restore is not implemented by blindly restoring the register
value, but by using the existing cpg_div6_clock_{en,dis}able() helpers.
Note that this does not yet support DIV6 clocks with multiple parents,
which do not exist on R-Car Gen3 SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
On R-Car Gen3 systems, PSCI system suspend powers down the SoC, possibly
losing clock configuration. Hence add a notifier chain that can be used
by core clocks to save/restore clock state during system suspend/resume.
The implementation of the actual clock state save/restore operations is
clock-specific, and to be registered with the notifier chain in the SoC
or family-specific cpg_mssr_info.cpg_clk_register() callback.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
During PSCI system suspend, R-Car Gen3 SoCs are powered down, and their
clock register state is lost. Note that as the boot loader skips most
initialization after system resume, clock register state differs from
the state encountered during normal system boot, too.
Hence after s2ram, some operations may fail because module clocks are
disabled, while drivers expect them to be still enabled. E.g. EtherAVB
fails when Wake-on-LAN has been enabled using "ethtool -s eth0 wol g":
ravb e6800000.ethernet eth0: failed to switch device to config mode
ravb e6800000.ethernet eth0: device will be stopped after h/w processes are done.
ravb e6800000.ethernet eth0: failed to switch device to config
PM: Device e6800000.ethernet failed to resume: error -110
In addition, some module clocks that were disabled by
clk_disable_unused() may have been re-enabled, wasting power.
To fix this, restore all bits of the SMSTPCR registers that represent
clocks under control of Linux.
Notes:
- While this fixes EtherAVB operation after resume from s2ram,
EtherAVB cannot be used as an actual wake-up source from s2ram, only
from s2idle, due to PSCI limitations,
- To avoid overhead on platforms not needing it, the suspend/resume
code has a build time dependency on sleep and PSCI support, and a
runtime dependency on PSCI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Add R-Car V3M (R8A77970) Clock Pulse Generator / Module Standby and
Software Reset support, using the CPG/MSSR driver core and the common
R-Car Gen3 code.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add R-Car D3 (R8A77995) Clock Pulse Generator / Module Standby and
Software Reset support, using the CPG/MSSR driver core and the common
R-Car Gen3 CPG code.
Based on the R-Car Series, 3rd Generation Hardware User's Manual, Rev.
0.55, Jun. 30, 2017.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
If CONFIG_OF=n:
drivers/clk/renesas/renesas-cpg-mssr.c: In function ‘cpg_mssr_probe’:
drivers/clk/renesas/renesas-cpg-mssr.c:702: warning: dereferencing ‘void *’ pointer
drivers/clk/renesas/renesas-cpg-mssr.c:702: error: request for member ‘data’ in something not a structure or union
To fix this, use the of_device_get_match_data() helper, for which a
dummy version is provided if CONFIG_OF=n.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a new R-Car E2 Clock Pulse Generator / Module Standby and Software
Reset driver, using the CPG/MSSR driver core. This will enable support
for module resets, which are not supported by the existing driver.
The old driver can still be used through a Kconfig option, to preserve
backward compatibility with old DTBs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a new R-Car V2H Clock Pulse Generator / Module Standby and Software
Reset driver, using the CPG/MSSR driver core. This will enable support
for module resets, which are not supported by the existing driver.
The old driver can still be used through a Kconfig option, to preserve
backward compatibility with old DTBs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a new R-Car M2-W/N Clock Pulse Generator / Module Standby and
Software Reset driver, using the CPG/MSSR driver core. This will enable
support for module resets, which are not supported by the existing
driver.
The old driver can still be used through a Kconfig option, to preserve
backward compatibility with old DTBs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a new R-Car H2 Clock Pulse Generator / Module Standby and Software
Reset driver, using the CPG/MSSR driver core. This will enable support
for module resets, which are not supported by the existing driver.
The old driver can still be used through a Kconfig option, to preserve
backward compatibility with old DTBs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The goals are to:
- Allow precise control over and automatic selection of which
(sub)drivers are used for which SoC (which may change in the
future),
- Allow adding support for new SoCs easily,
- Allow compile-testing of all (sub)drivers,
- Keep driver selection logic in the subsystem-specific Kconfig,
independent from the architecture-specific Kconfig (i.e. no "select"
from arch/arm64/Kconfig.platforms), to avoid dependencies.
This is implemented by:
- Introducing Kconfig symbols for all drivers and sub-drivers,
- Introducing the Kconfig symbol CLK_RENESAS, which is enabled
automatically when building for a Renesas ARM platform, and which
enables all required drivers without interaction of the user, based
on SoC-specific ARCH_* symbols,
- Allowing the user to enable any Kconfig symbol manually if
COMPILE_TEST is enabled,
- Using the new Kconfig symbols instead of the ARCH_* symbols to
control compilation in the Makefile,
- Always entering drivers/clk/renesas/ during the build.
Note that currently not all (sub)drivers are enabled for
compile-testing, as they depend on independent fixes in other
subsystems.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Coccinelle warns:
drivers/clk/renesas/renesas-cpg-mssr.c:323:14-21: ERROR: PTR_ERR applied after initialization to constant on line 260
Initialize clk using ERR_PTR(-ENOTSUPP) instead of NULL to fix this.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The pm_subsys_data.clock_list member exists only if CONFIG_PM_CLK=y.
Hence direct accesses to this field break compile-testing on platforms
where CONFIG_PM_CLK=n.
To fix this, use the pm_clk_no_clocks() helper instead, for which a
dummy version is provided if CONFIG_PM_CLK=n.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
The same SoC may have different clocks and/or module clock parents,
depending on SoC revision. One option is to use different sets of clock
tables for each SoC revision. However, if the differences are small, it
is much more space-efficient to have a single set of clock tables, and
fix those up at runtime instead.
Hence provide three helpers:
- Two helpers to NULLify core and module clocks that do not exist on
some revisions (NULLified clocks are skipped during the registration
phase),
- One helper to reparent module clocks that have different clock
parents.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add optional support for the Reset Control feature of the Renesas Clock
Pulse Generator / Module Standby and Software Reset module on R-Car
Gen2, R-Car Gen3, and RZ/G1 SoCs.
This allows to reset SoC devices using the Reset Controller API.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The spinlock is used to protect Read-Modify-Write register accesses,
which won't be limited to SMSTPCR register accesses.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
The Renesas CPG/MSSR driver is already in active use for RZ/G1 since
commits c0b2d75d2a ("clk: renesas: cpg-mssr: Add R8A7743 support")
and 9127d54bb8 ("clk: renesas: cpg-mssr: Add R8A7745 support").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
When the Renesas CPG/MSSR driver was introduced, it was anticipated that
critical clocks would be handled through a new CLK_ENABLE_HAND_OFF flag
soon. However, CLK_ENABLE_HAND_OFF never made it upstream.
Instead, commit 32b9b10961 ("clk: Allow clocks to be marked as
CRITICAL") introduced CLK_IS_CRITICAL, a flag with slightly differing
semantics. Still, it can be used to prevent e.g. the GIC module clock
from being turned off, until the GIC-400 driver has full support for
Runtime PM.
Hence migrate the Renesas CPG/MSSR driver from CLK_ENABLE_HAND_OFF to
CLK_IS_CRITICAL.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Add RZ/G1E (R8A7745) Clock Pulse Generator / Module Standby and Software
Reset support, using the CPG/MSSR driver core and the common R-Car Gen2
(and RZ/G) code.
Based on the proof-of-concept R8A7791 CPG/MSSR patch by Geert
Uytterhoeven <geert+renesas@glider.be>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add RZ/G1M (R8A7743) Clock Pulse Generator / Module Standby and Software
Reset support, using the CPG/MSSR driver core and the common R-Car Gen2
(and RZ/G) code.
Based on the proof-of-concept R8A7791 CPG/MSSR patch by Geert
Uytterhoeven <geert+renesas@glider.be>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The intention was to enable the checks if debugging is enabled, not
disabled.
Fixes: f793d1e517 ("clk: shmobile: Add new CPG/MSSR driver core")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Renesas CPG/MSSR driver core uses a mix of clk_readl()/clk_writel()
and readl()/writel() to access the clock registers. Settle on the
generic readl()/writel().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Initial support for R-Car M3-W (r8a7796), including basic core clocks,
and SCIF2 (console) and INTC-AP (GIC) module clocks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
As a pure Clock Domain does not have the concept of powering the domain
itself, the CPG/MSTP driver does not provide power_off() and power_on()
callbacks.
However, the genpd core may still perform a dummy power down, causing
/sys/kernel/debug/pm_genpd/pm_genpd_summary to report the domain's
status being "off-0".
Use the always-on governor to make sure the domain is never powered
down, and always shows up as "on" in pm_genpd_summary.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
All local setup of the generic_pm_domain structure should have been
completed before calling pm_genpd_init().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
The R-Car SYSC PM Domain driver has to power manage devices in power
areas using clocks. To reuse code and to share knowledge of clocks
suitable for power management, this is ideally done through the existing
cpg_mssr_attach_dev() and cpg_mssr_detach_dev() callbacks.
Hence these callbacks can no longer rely on their "domain" parameter
pointing to the CPG/MSSR Clock Domain. To handle this, keep a pointer to
the clock domain in a static variable. cpg_mssr_attach_dev() has to
support probe deferral, as the R-Car SYSC PM Domain may be initialized,
and devices may be added to it, before the CPG/MSSR Clock Domain is
initialized.
Dummy callbacks are provided for the case where CPG/MSTP support is not
included, so the rcar-sysc driver won't have to care about this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
As of commit 71d076ceb2 ("ARM: shmobile: Enable PM and
PM_GENERIC_DOMAINS for SoCs with PM Domains"),
CONFIG_PM_GENERIC_DOMAINS_OF is always enabled for SoCs with a CPG/MSSR
block.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Gen3 has two clocks (OSC and R) which look like a DIV6 clock but their
divider value is read-only and depends on MD pins at bootup. Add support
for such clocks by reading the value and adding a fixed clock.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Along with the above mentioned Kconfig changes it seems appropriate
to also rename directories that only hold drivers for such SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Stephen Boyd