The supported_rates field should contain all our supported
rates, even if the remote peer doesn't support them.
(rename CONF_TX_AP_ENABLED_RATES to CONF_TX_ENABLED_RATES,
as we now use it for both ap and sta)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The IEEE80211_TX_CTL_NO_CCK_RATE flag is only set for mgmt packets
transmitted during p2p connection setup. Make sure to use the lowest
OFDM rate guarantee the peer always hears us.
Change the p2p rate policy to contain only the 6mpbs rate to acheive
this effect.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Hold a value for sta_sleep_auth that is amenable to change by debugfs.
When detecting a legal value in this variable on interface init, use it
as an override value for sleep_auth.
This makes debugging more intuitive using the debugfs value.
Increment the conf version since we added an element to the conf
structure.
Note: An AP going up will always set sleep_auth to PSM_CAM.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Since we are now going to export the conf structure and read it from a
file, it should be packed to avoid surprises with padding bytes.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Since we will export the conf structure as a file, we need to use well
defined types. Instead of using enum, whose size may vary, use u8 for
bcn_filt_mode instead.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The conf structure is going to be exported to a file, so we should use
only well defined types. bool is not well defined and may vary from
platform to platform, so change the host_fast_wakeup_support type to
u8 instead.
Signed-off-by: Luciano Coelho <coelho@ti.com>
In the enum conf_tx_ac CONF_TX_AC_ANY_TID should
be 0xff to match the firmware's implementation.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Define HW-rate conversion tables for the 18xx chip. Initialize
the appropriate wlcore elements with these tables and values to allow
conversion of HW-rates.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Instead of having two memory configuration sets, one for wl127x and
one for wl128x, we can use only one which should be correctly set by
the lower driver.
The wl12xx driver now uses the wl128x memory config by default but
changes it when if it identifies the wl127x chips.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The extended radio configuration parameters are only used by the
wl127x chipsets, which are handled by the wl12xx driver. Move the rf
configuration settings from wlcore to wl12xx.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The configuration parameters vary with different chip families. Some
of the parameters used only by some chip families, others should have
different value depending on the family. Thus move the configuration
values from wlcore to wl12xx.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Rates reported by HW can be different between chip families. Make the
rate-to-idx translation tables private per family and use them in a
common translation function. Add a global element to help determine
which rates are HW HT-rates.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add register tables support in wlcore, add some new IO functions to
read and write to chip-specific register and data addresses. Move
some common register values from wl12xx to wlcore and add the
registers table to wl12xx.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Rename the wl12xx driver directory to wlcore as an initial step
towards the split of the driver into wlcore and wl12xx. We just
rename the directory first to keep git blame happy.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller