On some platforms the clock can be fixed rate, always running one and
there is no need to do anything with it.
In order to support those platforms, switch to use optional clock.
Fixes: f8d9ddbc28 ("dmaengine: dw: platform: Enable iDMA 32-bit on Intel Elkhart Lake")
Depends-on: 60b8f0ddf1 ("clk: Add (devm_)clk_get_optional() functions")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20190924085116.83683-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Move ACPI handle check to the dw_dma_acpi_controller_register().
While here, convert it to has_acpi_companion() which is recommended way.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190820131546.75744-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is a possibility to have registered ACPI DMA controller
while it has been gone already.
To avoid the potential crash, move to non-managed
acpi_dma_controller_register().
Fixes: 42c91ee71d ("dw_dmac: add ACPI support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190820131546.75744-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Intel® PSE (Programmable Services Engine) provides few DMA controllers
to the host on Intel Elkhart Lake. Enable them in the ACPI glue driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190820131546.75744-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We are expecting some devices can be enumerated either as PCI or ACPI.
Nevertheless, they will share same information, thus, provide a generic
struct dw_dma_chip_pdata for all glue drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190820131546.75744-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Intel Elkhart Lake Offload Service Engine (OSE) will be called as
Intel(R) Programmable Services Engine (Intel(R) PSE) in documentation.
Update the comment here accordingly.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20190813080602.15376-1-jarkko.nikula@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Intel Elkhart Lake OSE (Offload Service Engine) provides few DMA controllers
to the host. Enable them in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the same way as done for ->probe(), call ->remove() based on
the type of the hardware.
While it works now due to equivalency of the two removal functions,
it might be changed in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Intel iDMA 32-bit doesn't have a concept of bus masters and thus
there is no need to setup any kind of masters in the CTL_LO register.
Moreover, the burst size for memory-to-memory transfer is not what is says,
we need to have a corrected list of possible sizes. Note, that
the size of 8 items, each of that up to 4 bytes, is chosen because of
maximum of 1/2 FIFO, which is 64 bytes on Intel Merrifield.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For Intel iDMA 32-bit the channel can be drained on a suspend.
We need to reset the bit on the resume to return a status quo.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Here is a kinda big refactoring that should have been done
in the first place, when Intel iDMA 32-bit support appeared.
It splits operations which are different to Synopsys DesignWare and
Intel iDMA 32-bit controllers.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
All known devices, which use DT for configuration, support
memory-to-memory transfers. So enable it by default.
The rest two cases, i.e. Intel Quark and PPC460ex, instantiate DMA driver and
use its channels exclusively for hardware, which means there is no available
channel for any other purposes anyway.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The commit a9ddb575d6
("dmaengine: dw_dmac: Enhance device tree support")
introduces is_private property in uncertain understanding what does it mean.
First of all, documentation defines DMA_PRIVATE capability as
Documentation/crypto/async-tx-api.txt:
The DMA_PRIVATE capability flag is used to tag dma devices that should not be
used by the general-purpose allocator. It can be set at initialization time
if it is known that a channel will always be private. Alternatively,
it is set when dma_request_channel() finds an unused "public" channel.
A couple caveats to note when implementing a driver and consumer:
1/ Once a channel has been privately allocated it will no longer be
considered by the general-purpose allocator even after a call to
dma_release_channel().
2/ Since capabilities are specified at the device level a dma_device with
multiple channels will either have all channels public, or all channels
private.
Documentation/driver-api/dmaengine/provider.rst:
- DMA_PRIVATE
The devices only supports slave transfers, and as such isn't available
for async transfers.
The capability had been introduced by the commit 59b5ec2144
("dmaengine: introduce dma_request_channel and private channels")
and some code didn't changed from that times ever.
Taking into consideration above and the fact that on all known platforms
Synopsys DesignWare DMA engine is attached to serve slave transfers,
the DMA_PRIVATE capability must be enabled for this device unconditionally.
Otherwise, as rightfully noticed in drivers/dma/at_xdmac.c:
/*
* Without DMA_PRIVATE the driver is not able to allocate more than
* one channel, second allocation fails in private_candidate.
*/
because of of a caveats mentioned in above documentation excerpts.
So, remove conditional around DMA_PRIVATE followed by removal leftovers.
If someone wonders, DMA_PRIVATE can be not used if and only if the all channels
of the DMA controller are supposed to serve memory-to-memory like operations.
For example, EP93xx has two controllers, one of which can only perform
memory-to-memory transfers
Note, this change doesn't affect dmatest to be able to test such controllers.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> (maintainer:SERIAL DRIVERS)
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Drop LIST_HEAD where the variable it declares is never used.
Commit ab703f818a ("dmaengine: dw: lazy allocation of dma
descriptors") removed the uses, but not the declaration.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier x;
@@
- LIST_HEAD(x);
... when != x
// </smpl>
Fixes: ab703f818a ("dmaengine: dw: lazy allocation of dma descriptors")
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dmaengine updates for v4.21-rc1
- New driver for UniPhier MIO DMA controller
- Remove R-Mobile APE6 support
- Sprd driver updates and support for cyclic link-list
- Remove dma_slave_config direction usage from rest of drivers
- Minor updates to dmatest, dw-dmac, zynqmp and bcm dma drivers
-----BEGIN PGP SIGNATURE-----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=+pTt
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.21-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This includes a new driver, removes R-Mobile APE6 as it is no longer
used, sprd cyclic dma support, last batch of dma_slave_config
direction removal and random updates to bunch of drivers.
Summary:
- New driver for UniPhier MIO DMA controller
- Remove R-Mobile APE6 support
- Sprd driver updates and support for cyclic link-list
- Remove dma_slave_config direction usage from rest of drivers
- Minor updates to dmatest, dw-dmac, zynqmp and bcm dma drivers"
* tag 'dmaengine-4.21-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (48 commits)
dmaengine: qcom_hidma: convert to DEFINE_SHOW_ATTRIBUTE
dmaengine: pxa: remove DBGFS_FUNC_DECL()
dmaengine: mic_x100_dma: convert to DEFINE_SHOW_ATTRIBUTE
dmaengine: amba-pl08x: convert to DEFINE_SHOW_ATTRIBUTE
dmaengine: Documentation: Add documentation for multi chan testing
dmaengine: dmatest: Add transfer_size parameter
dmaengine: dmatest: Add alignment parameter
dmaengine: dmatest: Use fixed point div to calculate iops
dmaengine: dmatest: Add support for multi channel testing
dmaengine: rcar-dmac: Document R8A774C0 bindings
dt-bindings: dmaengine: usb-dmac: Add binding for r8a774c0
dmaengine: zynqmp_dma: replace spin_lock_bh with spin_lock_irqsave
dmaengine: sprd: Add me as one of the module authors
dmaengine: sprd: Support DMA 2-stage transfer mode
dmaengine: sprd: Support DMA link-list cyclic callback
dmaengine: sprd: Set cur_desc as NULL when free or terminate one dma channel
dmaengine: sprd: Fix the last link-list configuration
dmaengine: sprd: Get transfer residue depending on the transfer direction
dmaengine: sprd: Remove direction usage from struct dma_slave_config
dmaengine: dmatest: fix a small memory leak in dmatest_func()
...
Intel Merrifield has a reduced size of FIFO used in iDMA 32-bit controller,
i.e. 512 bytes instead of 1024.
Fix this by partitioning it as 64 bytes per channel.
Note, in the future we might switch to 'fifo-size' property instead of
hard coded value.
Fixes: 199244d694 ("dmaengine: dw: add support of iDMA 32-bit hardware")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds a new device-tree property that allows to
specify the dma protection control bits for the all of the
DMA controller's channel uniformly.
Setting the "correct" bits can have a huge impact on the
PPC460EX and APM82181 that use this DMA engine in combination
with a DesignWare' SATA-II core (sata_dwc_460ex driver).
In the OpenWrt Forum, the user takimata reported that:
|It seems your patch unleashed the full power of the SATA port.
|Where I was previously hitting a really hard limit at around
|82 MB/s for reading and 27 MB/s for writing, I am now getting this:
|
|root@OpenWrt:/mnt# time dd if=/dev/zero of=tempfile bs=1M count=1024
|1024+0 records in
|1024+0 records out
|real 0m 13.65s
|user 0m 0.01s
|sys 0m 11.89s
|
|root@OpenWrt:/mnt# time dd if=tempfile of=/dev/null bs=1M count=1024
|1024+0 records in
|1024+0 records out
|real 0m 8.41s
|user 0m 0.01s
|sys 0m 4.70s
|
|This means: 121 MB/s reading and 75 MB/s writing!
|
|The drive is a WD Green WD10EARX taken from an older MBL Single.
|I repeated the test a few times with even larger files to rule out
|any caching, I'm still seeing the same great performance. OpenWrt is
|now completely on par with the original MBL firmware's performance.
Another user And.short reported:
|I can report that your fix worked! Boots up fine with two
|drives even with more partitions, and no more reboot on
|concurrent disk access!
A closer look into the sata_dwc_460ex code revealed that
the driver did initally set the correct protection control
bits. However, this feature was lost when the sata_dwc_460ex
driver was converted to the generic DMA driver framework.
BugLink: https://forum.openwrt.org/t/wd-mybook-live-duo-two-disks/16195/55
BugLink: https://forum.openwrt.org/t/wd-mybook-live-duo-two-disks/16195/50
Fixes: 8b3444852a ("sata_dwc_460ex: move to generic DMA driver")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dma_slave_config direction was marked as deprecated quite some
time back, remove the usage from this driver so that the field
can be removed
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Bay and Cherry Trail DSTDs represent a different set of devices depending
on which OS the device think it is booting. One set of decices for Windows
and another set of devices for Android which targets the Android-x86 Linux
kernel fork (which e.g. used to have its own display driver instead of
using the i915 driver).
Which set of devices we are actually going to get is out of our control,
this is controlled by the ACPI OSID variable, which gets either set through
an EFI setup option, or sometimes is autodetected. So we need to support
both.
This commit adds support for the 80862286 and 808622C0 ACPI HIDs which we
get for the first resp. second DMA controller on Cherry Trail devices when
OSID is set to Android.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
AVR32 is gone. Now it's time to clean up the driver by removing
leftovers that was used by AVR32 related code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This time we fairly boring and bit small update.
- Support for Intel iDMA 32-bit hardware
- deprecate broken support for channel switching in async_tx
- bunch of updates on stm32-dma
- Cyclic support for zx dma and making in generic zx dma driver
- Small updates to bunch of other drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pcdH
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.11-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we fairly boring and bit small update.
- Support for Intel iDMA 32-bit hardware
- deprecate broken support for channel switching in async_tx
- bunch of updates on stm32-dma
- Cyclic support for zx dma and making in generic zx dma driver
- Small updates to bunch of other drivers"
* tag 'dmaengine-4.11-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (29 commits)
async_tx: deprecate broken support for channel switching
dmaengine: rcar-dmac: Widen DMA mask to 40 bits
dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
dmaengine: Provide a wrapper for memcpy operations
dmaengine: zx: fix build warning
dmaengine: dw: we do support Merrifield SoC in PCI mode
dmaengine: dw: add support of iDMA 32-bit hardware
dmaengine: dw: introduce register mappings for iDMA 32-bit
dmaengine: dw: introduce block2bytes() and bytes2block()
dmaengine: dw: extract dwc_chan_pause() for future use
dmaengine: dw: replace convert_burst() with one liner
dmaengine: dw: register IRQ and DMA pool with instance ID
dmaengine: dw: Fix data corruption in large device to memory transfers
dmaengine: ste_dma40: indicate granularity on channels
dmaengine: ste_dma40: indicate directions on channels
dmaengine: stm32-dma: Add error messages if xlate fails
dmaengine: dw: pci: remove LPE Audio DMA ID
dmaengine: stm32-dma: Add max_burst support
dmaengine: stm32-dma: Add synchronization support
dmaengine: stm32-dma: Fix residue computation issue in cyclic mode
...
Intel Merrifield platform contains Intel integrated DMA (iDMA 32-bit) which has
a slightly different register mapping, e.g. some bits in CTL_* and CFG_*
channel registers, and has to use platform data since there is no
autoconfiguration.
The iDMA 32-bit specification is available in the publicly available
documentation for Intel Braswell and BayTrail SoCs as LPE Audio DMA.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
iDMA 32-bit is Intel designed DMA controller that behaves like Synopsys
Designware DMA. This patch adds a support of the new Intel hardware.
Due to iDMA 32-bit has no autoconfiguration the platform code must
provide a platform data to dw_dma_probe().
By default full FIFO (1024 bytes) is assigned to channel 0. Here we
slice FIFO on equal parts between channels for iDMA 32-bit case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The integrated DMA (iDMA 32-bit) is Intel designed DMA controller which
mimics Synopsys Designware DMA. This patch appends the register mappings
for the parts which are slightly different to the DesignWare hardware.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The newly introduced helpers prepare driver to support new DMA controller
hardware.
While here, introduce DWC_CTLH_BLOCK_TS() macro as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
iDMA 32-bit has a special handling of the FIFO during pause() /
terminate_all(). Prepare code to implement that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Replace convert_burst() with one liner in place.
The change simplifies further extension of the driver to cover new DMA
controller hardware.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It is really useful not only for debugging to have an IRQ line and DMA
pool labeled with driver and its instance ID. Do this for DesignWare DMA
driver.
All current users of this IP would be enhanced later on.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When transferring more data than the maximum block size supported by the
HW multiplied by source width the transfer is split into smaller chunks.
Currently code calculates the memory width and thus aligment before
splitting for both memory to device and device to memory transfers.
For memory to device transfers this work fine since alignment is preserved
through the splitting and split blocks are still memory width aligned.
However in device to memory transfers aligment breaks when maximum block
size multiplied by register width doesn't have the same alignment than the
buffer. For instance when transferring from an 8-bit register 4100 bytes
(32-bit aligned) on a DW DMA that has maximum block size of 4095 elements.
An attempt to do such transfers caused data corruption.
Fix this by calculating and setting the destination memory width after
splitting by using the split block aligment and length.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
LPE Audio driver should take care of DMA IPs by itself. Keeping an ID like this
in dw_dma_pci.c is anyway wrong since that block has two DMA controllers under
one ID (like MFD device).
That's also why I didn't include LPE Audio ID for Intel Merrifield previously.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Several versions of DW DMAC have multi block transfers hardware
support. Hardware support of multi block transfers is disabled
by default if we use DT to configure DMAC and software emulation
of multi block transfers used instead.
Add multi-block property, so it is possible to enable hardware
multi block transfers (if present) via DT.
Switch from per device is_nollp variable to multi_block array
to be able enable/disable multi block transfers separately per
channel.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
All known devices, which use DT for configuration, support
memory-to-memory transfers. So enable it by default, if we read
configuration from DT.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is bit large pile of code which bring in some nice additions:
- Error reporting: we have added a new mechanism for users of dmaenegine to
register a callback_result which tells them the result of the dma
transaction. Right now only one user ntb is using it.
- As we discussed on KS mailing list and pointed out NO_IRQ has no place in
kernel, this also remove NO_IRQ from dmaengine subsystem (both arm and
ppc users)
- Support for IOMMU slave transfers and it implementation for arm.
- To get better build coverage, enable COMPILE_TEST for bunch of driver,
and fix the warning and sparse complaints on these.
- Apart from above, usual updates spread across drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJX9cGYAAoJEHwUBw8lI4NHXh0P/3OsctPYnwcangOz268hHDap
7ZHwau96K7DRi8cFCc0XmG083Ivqih/fWMFJBUOEsuwS3zPHkfgfhsvm7MqrK3vv
psJIwnubwTVVQ3lePYJlnna6mijcRNXVAooRLiqylA3QPIYRxECDFVDRNwf39D+I
bYp5tmlFcobugOUUoMqq1D/gH8EHUWxrnrsS6UBBpYm+cusc6u9/JXlOb4pcJGSL
V340zQ0S9FNuEM3b+1kMAeq3DG2wLXv9oJzz/6EN59sx5AdjlYUPHd/PvTYOeG0T
crdtDfL+7xcqP0Ms4SGTOD4kXSe6nErr3bIBHQXI6ZmJn0j//+3yU21kTMl95kM+
RM7nE4vItuQR0jPxVlhuLCcf3q7zMi+noOPZ1DVRTE1Yf9AizAgbPXyOE+jzGUUi
6E+0Mj6CLpFH/Mffxphs7L6GKwfWqaLjAupbjR6EWZud37KAwvpcB1CkJEgT9C4s
OiZ4INTPxXmw9dX/T9CPOyh8oZ8mB9LTUzHoJDvDGuwYm7HE0U9pzHG4bP0mjIIt
y3RboP78t1HC9oZUrxCoGhvekJtok0k3RLGJTSx9ujklY9MJGG/F1KEC6APp5tXu
0UToMXpgXSUkKEZesmsJFj/lbh1+h/yo5zTG5Hek8lh1K0sczaoWu3xTTSY9SSZQ
ihlqyvdzSBweKo8ktU8A
=9iA3
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.9-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This is bit large pile of code which bring in some nice additions:
- Error reporting: we have added a new mechanism for users of
dmaenegine to register a callback_result which tells them the
result of the dma transaction. Right now only one user (ntb) is
using it.
- As we discussed on KS mailing list and pointed out NO_IRQ has no
place in kernel, this also remove NO_IRQ from dmaengine subsystem
(both arm and ppc users)
- Support for IOMMU slave transfers and its implementation for arm.
- To get better build coverage, enable COMPILE_TEST for bunch of
driver, and fix the warning and sparse complaints on these.
- Apart from above, usual updates spread across drivers"
* tag 'dmaengine-4.9-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (169 commits)
async_pq_val: fix DMA memory leak
dmaengine: virt-dma: move function declarations
dmaengine: omap-dma: Enable burst and data pack for SG
DT: dmaengine: rcar-dmac: document R8A7743/5 support
dmaengine: fsldma: Unmap region obtained by of_iomap
dmaengine: jz4780: fix resource leaks on error exit return
dma-debug: fix ia64 build, use PHYS_PFN
dmaengine: coh901318: fix integer overflow when shifting more than 32 places
dmaengine: edma: avoid uninitialized variable use
dma-mapping: fix m32r build warning
dma-mapping: fix ia64 build, use PHYS_PFN
dmaengine: ti-dma-crossbar: enable COMPILE_TEST
dmaengine: omap-dma: enable COMPILE_TEST
dmaengine: edma: enable COMPILE_TEST
dmaengine: ti-dma-crossbar: Fix of_device_id data parameter usage
dmaengine: ti-dma-crossbar: Correct type for of_find_property() third parameter
dmaengine/ARM: omap-dma: Fix the DMAengine compile test on non OMAP configs
dmaengine: edma: Rename set_bits and remove unused clear_bits helper
dmaengine: edma: Use correct type for of_find_property() third parameter
dmaengine: edma: Fix of_device_id data parameter usage (legacy vs TPCC)
...
There are at least two known devices, e.g. DMA controller found on ARC AXS101
SDP board, that have LLP register and no multi block transfer support at the
same time.
Override autodetection by user provided data.
Reported-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Quark UART uses DesignWare DMA IP. Though the DMA IP is connected in such
way that handshake interface uses inverted polarity. We have to provide a
possibility to set this in the DMA driver when configuring a channel.
Introduce a new member of custom slave configuration called 'hs_polarity' and
set active low polarity in case this value is 'true'.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It seems we need to extend custom slave configuration by one more member to
support Intel Quart UART. It becomes a burden to manage all members of struct
dw_dma_slave one-by-one.
Replace the set of fields by embedding struct dw_dma_slave into struct
dw_dma_chan.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is in preperation of moving to a callback that provides results to the
callback for the transaction. The conversion will maintain current behavior
and the driver must convert to new callback mechanism at a later time in
order to receive results.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Viresh Kumar <vireshk@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We pass struct dw_dma_chip to dw_dma_probe() anyway, thus we may use it to
pass a platform data as well.
While here, constify the source of the platform data.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Andy Shevchenko