The Allwinner SoCs have a handful of SRAM that can be either mapped to be
accessible by devices or the CPU.
That mapping is controlled by an SRAM controller, and that mapping might
not be set by the bootloader, for example if the device wasn't used at all,
or if we're using solutions like the U-Boot's Falcon Boot.
We could also imagine changing this at runtime for example to change the
mapping of these SRAMs to use them for suspend/resume or runtime memory
rate change, if that ever happens.
These use cases require some API in the kernel to control that mapping,
exported through a drivers/soc driver.
This driver also implement a debugfs file that shows the SRAM found in the
system, the current mapping and the SRAM that have been claimed by some
drivers in the kernel.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The pmic-wrapper calls the reset controller. If CONFIG_RESET_CONTROLLER
is not set, compilation fails with:
drivers/soc/mediatek/mtk-pmic-wrap.c: In function ‘pwrap_probe’:
drivers/soc/mediatek/mtk-pmic-wrap.c:836:2: error: implicit declaration of function ‘devm_reset_control_get’ [-Werror=implicit-function-declaration]
This patch sets the dependency in the Kconfig file.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
When the PMIC wrapper state machine has read a register it goes into the
"wait for valid clear" (vldclr) state. The state machine stays in this
state until the VLDCLR bit is written to. We should write this bit after
reading a register because the SCPSYS won't let the system go into
suspend as long as the state machine waits for valid clear.
Since now we never leave the state machine in vldclr state we no longer
have to check for this state on pwrap_read/pwrap_write entry and can
remove the corresponding code.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
replace chipselect extension values based on SPI clock with hardcoded SoC
specific values.
The PMIC wrapper has the ability of extending the chipselects by configurable
amounts of time. We configured the values based on the rate of SPI clock, but
this is wrong. The delays should be configured based on the internal PMIC clock
that latches the values from the SPI bus to the internal PMIC registers. By
default this clock is 24MHz. Other clock frequencies are for debugging only
and can be removed from the driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The pmc driver was previously exporting tegra_pmc_restart, which was
assigned to machine_desc.init_machine, taking precedence over the
restart handlers registered through register_restart_handler().
Signed-off-by: David Riley <davidriley@chromium.org>
[tomeu.vizoso@collabora.com: Rebased]
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
[treding@nvidia.com: minor cleanups]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Needed for the EMC and MC drivers to know what timings from the DT to
use.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The return type of the wait_for_completion_timeout() function is not int
but unsigned long. An appropriately named unsigned long is added and the
assignment fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
SPM is a hardware block that controls the peripheral logic surrounding
the application cores (cpu/l$). When the core executes WFI instruction,
the SPM takes over the putting the core in low power state as
configured. The wake up for the SPM is an interrupt at the GIC, which
then completes the rest of low power mode sequence and brings the core
out of low power mode.
The SPM has a set of control registers that configure the SPMs
individually based on the type of the core and the runtime conditions.
SPM is a finite state machine block to which a sequence is provided and
it interprets the bytes and executes them in sequence. Each low power
mode that the core can enter into is provided to the SPM as a sequence.
Configure the SPM to set the core (cpu or L2) into its low power mode,
the index of the first command in the sequence is set in the SPM_CTL
register. When the core executes ARM wfi instruction, it triggers the
SPM state machine to start executing from that index. The SPM state
machine waits until the interrupt occurs and starts executing the rest
of the sequence until it hits the end of the sequence. The end of the
sequence jumps the core out of its low power mode.
Add support for an idle driver to set up the SPM to place the core in
Standby or Standalone power collapse mode when the core is idle.
Based on work by: Mahesh Sivasubramanian <msivasub@codeaurora.org>,
Ai Li <ali@codeaurora.org>, Praveen Chidambaram <pchidamb@codeaurora.org>
Original tree available at -
git://codeaurora.org/quic/la/kernel/msm-3.10.git
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Kumar Gala <galak@codeaurora.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
The PMIC wrapper driver adds a couple of variables that are never used.
Remove them to avoid build warnings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds support for the PMIC wrapper found on MediaTek MT8135 and
MT8173 SoCs. The PMIC wrapper is found on MT6xxx SoCs aswell but these
are currently not supported.
On MediaTek MT8135, MT8173 and other SoCs the PMIC is connected via
SPI. The SPI master interface is not directly visible to the CPU, but
only through the PMIC wrapper inside the SoC. The communication between
the SoC and the PMIC can optionally be encrypted. Also a non standard
Dual IO SPI mode can be used to increase speed. The MT8135 also supports
a special feature named "IP Pairing". With IP Pairing the pins of some
SoC internal peripherals can be on the PMIC. The signals of these pins
are routed over the SPI bus using the pwrap bridge. Because of these
optional non SPI conform features the PMIC driver is not implemented as
a SPI bus master driver.
Signed-off-by: Flora Fu, MediaTek
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch adds automatic configuration for the ADM CRCI muxing required to
support DMA operations for GSBI clients. The GSBI mode and instance determine
the correct TCSR ADM CRCI MUX value that must be programmed so that the DMA
works properly.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
This time around, much of this is for at91, with the bulk of it being syscon
and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=T7R2
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
This time around, much of this is for at91, with the bulk of it being
syscon and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
cpuidle: exynos: add coupled cpuidle support for exynos4210
ARM: EXYNOS: apply S5P_CENTRAL_SEQ_OPTION fix only when necessary
soc: ti: knav_qmss_queue: change knav_range_setup_acc_irq to static
soc: ti: knav_qmss_queue: makefile tweak to build as dynamic module
pcmcia: at91_cf: depend on !ARCH_MULTIPLATFORM
soc: ti: knav_qmss_queue: export API calls for use by user driver
of/platform: teardown DMA mappings on device destruction
usb: gadget: at91_udc: Allocate udc instance
usb: gadget: at91_udc: Update DT binding documentation
usb: gadget: at91_udc: Rework for multi-platform kernel support
usb: gadget: at91_udc: Simplify probe and remove functions
usb: gadget: at91_udc: Remove non-DT handling code
usb: gadget: at91_udc: Document DT clocks and clock-names property
usb: gadget: at91_udc: Drop uclk clock
usb: gadget: at91_udc: Fix clock names
mfd: syscon: Add Atmel SMC binding doc
mfd: syscon: Add atmel-smc registers definition
mfd: syscon: Add Atmel Matrix bus DT binding documentation
mfd: syscon: Add atmel-matrix registers definition
clk: shmobile: fix sparse NULL pointer warning
...
knav_range_setup_acc_irq() is used only within the file and should
be defined as static.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Currently configuring qmss and dma as dynamic module creates three .ko
files. knav_qmss_acc.ko and knav_qmss_queue.ko both can't be insmod
because of circular dependency. So combine these two into one module
by changing the makefile.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Currently only few of the API calls are exported. This creates problem
when the knav* modules are built as modules and another user module
such as netcp_core try to use these API calls and they are also built
as module. This patch export these APIs to address the issue.
This is needed to support allmodconfig for ARM
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
This adds a device tree controlled option to enable PMC-based
thermal reset in overheating situations. Thermtrip is supported on
Tegra30, Tegra114 and Tegra124. The thermal reset only works when
the thermal sensors are calibrated, so a soctherm driver is also
required.
The thermtrip event is triggered by the soctherm block, and all
soctherm sensors default to showing a temperature of zero Celsius
before they are initialized. Because of this, it is safe to initialize
thermtrip and soctherm in any order.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra132 uses the same GPU as Tegra124 and therefore requires the same
method to remove clamps. However Tegra132 has a separate chip ID, so in
order to avoid having to extend the list of chip IDs for the special
case, add a feature flag to the SoC data.
Reviewed-by: Paul Walmsley <pwalmsley@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra132 is very similar to Tegra124 from a peripheral point of view and
uses the same fuse controller.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra SoCs with 64-bit ARM support don't currently support deep CPU
low-power states in mainline Linux. When this support is added in the
future, it will probably look rather different from the existing
32-bit ARM support, since the ARM64 maintainers' strong preference is
to use PSCI to implement it.
So, for the time being, prevent the CPU suspend-related code and data
in the Tegra PMC driver from compiling on ARM64.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Allen Martin <amartin@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pull drm updates from Dave Airlie:
"Highlights:
- AMD KFD driver merge
This is the AMD HSA interface for exposing a lowlevel interface for
GPGPU use. They have an open source userspace built on top of this
interface, and the code looks as good as it was going to get out of
tree.
- Initial atomic modesetting work
The need for an atomic modesetting interface to allow userspace to
try and send a complete set of modesetting state to the driver has
arisen, and been suffering from neglect this past year. No more,
the start of the common code and changes for msm driver to use it
are in this tree. Ongoing work to get the userspace ioctl finished
and the code clean will probably wait until next kernel.
- DisplayID 1.3 and tiled monitor exposed to userspace.
Tiled monitor property is now exposed for userspace to make use of.
- Rockchip drm driver merged.
- imx gpu driver moved out of staging
Other stuff:
- core:
panel - MIPI DSI + new panels.
expose suggested x/y properties for virtual GPUs
- i915:
Initial Skylake (SKL) support
gen3/4 reset work
start of dri1/ums removal
infoframe tracking
fixes for lots of things.
- nouveau:
tegra k1 voltage support
GM204 modesetting support
GT21x memory reclocking work
- radeon:
CI dpm fixes
GPUVM improvements
Initial DPM fan control
- rcar-du:
HDMI support added
removed some support for old boards
slave encoder driver for Analog Devices adv7511
- exynos:
Exynos4415 SoC support
- msm:
a4xx gpu support
atomic helper conversion
- tegra:
iommu support
universal plane support
ganged-mode DSI support
- sti:
HDMI i2c improvements
- vmwgfx:
some late fixes.
- qxl:
use suggested x/y properties"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (969 commits)
drm: sti: fix module compilation issue
drm/i915: save/restore GMBUS freq across suspend/resume on gen4
drm: sti: correctly cleanup CRTC and planes
drm: sti: add HQVDP plane
drm: sti: add cursor plane
drm: sti: enable auxiliary CRTC
drm: sti: fix delay in VTG programming
drm: sti: prepare sti_tvout to support auxiliary crtc
drm: sti: use drm_crtc_vblank_{on/off} instead of drm_vblank_{on/off}
drm: sti: fix hdmi avi infoframe
drm: sti: remove event lock while disabling vblank
drm: sti: simplify gdp code
drm: sti: clear all mixer control
drm: sti: remove gpio for HDMI hot plug detection
drm: sti: allow to change hdmi ddc i2c adapter
drm/doc: Document drm_add_modes_noedid() usage
drm/i915: Remove '& 0xffff' from the mask given to WA_REG()
drm/i915: Invert the mask and val arguments in wa_add() and WA_REG()
drm: Zero out DRM object memory upon cleanup
drm/i915/bdw: Fix the write setting up the WIZ hashing mode
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
The largest single change here this time around is the Tegra
iommu/memory controller driver, which gets updated to the new
iommu DT binding. More drivers like this are likely to follow
for the following merge window, but we should be able to do
those through the iommu maintainer.
Other notable changes are:
* reset controller drivers from the reset maintainer (socfpga, sti, berlin)
* fixes for the keystone navigator driver merged last time
* at91 rtc driver changes related to the at91 cleanups
* ARM perf driver changes from Will Deacon
* updates for the brcmstb_gisb driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=MwMG
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
The largest single change here this time around is the Tegra
iommu/memory controller driver, which gets updated to the new iommu DT
binding. More drivers like this are likely to follow for the
following merge window, but we should be able to do those through the
iommu maintainer.
Other notable changes are:
- reset controller drivers from the reset maintainer (socfpga, sti,
berlin)
- fixes for the keystone navigator driver merged last time
- at91 rtc driver changes related to the at91 cleanups
- ARM perf driver changes from Will Deacon
- updates for the brcmstb_gisb driver"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
clocksource: arch_timer: Allow the device tree to specify uninitialized timer registers
clocksource: arch_timer: Fix code to use physical timers when requested
memory: Add NVIDIA Tegra memory controller support
bus: brcmstb_gisb: Add register offset tables for older chips
bus: brcmstb_gisb: Look up register offsets in a table
bus: brcmstb_gisb: Introduce wrapper functions for MMIO accesses
bus: brcmstb_gisb: Make the driver buildable on MIPS
of: Add NVIDIA Tegra memory controller binding
ARM: tegra: Move AHB Kconfig to drivers/amba
amba: Add Kconfig file
clk: tegra: Implement memory-controller clock
serial: samsung: Fix serial config dependencies for exynos7
bus: brcmstb_gisb: resolve section mismatch
ARM: common: edma: edma_pm_resume may be unused
ARM: common: edma: add suspend resume hook
powerpc/iommu: Rename iommu_[un]map_sg functions
rtc: at91sam9: add DT bindings documentation
rtc: at91sam9: use clk API instead of relying on AT91_SLOW_CLOCK
ARM: at91: add clk_lookup entry for RTT devices
rtc: at91sam9: rework the Kconfig description
...
New and updated SoC support, notable changes include:
* bcm: brcmstb SMP support
* bcm: initial iproc/cygnus support
* exynos: Exynos4415 SoC support
* exynos: PMU and suspend support for Exynos5420
* exynos: PMU support for Exynos3250
* exynos: pm related maintenance
* imx: new LS1021A SoC support
* imx: vybrid 610 global timer support
* integrator: convert to using multiplatform configuration
* mediatek: earlyprintk support for mt8127/mt8135
* meson: meson8 soc and l2 cache controller support
* mvebu: Armada 38x CPU hotplug support
* mvebu: drop support for prerelease Armada 375 Z1 stepping
* mvebu: extended suspend support, now works on Armada 370/XP
* omap: hwmod related maintenance
* omap: prcm cleanup
* pxa: initial pxa27x DT handling
* rockchip: SMP support for rk3288
* rockchip: add cpu frequency scaling support
* shmobile: r8a7740 power domain support
* shmobile: various small restart, timer, pci apmu changes
* sunxi: Allwinner A80 (sun9i) earlyprintk support
* ux500: power domain support
Overall, a significant chunk of changes, coming mostly from
the usual suspects: omap, shmobile, samsung and mvebu, all of
which already contain a lot of platform specific code in
arch/arm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lFoH
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Arnd Bergmann:
"New and updated SoC support, notable changes include:
- bcm:
brcmstb SMP support
initial iproc/cygnus support
- exynos:
Exynos4415 SoC support
PMU and suspend support for Exynos5420
PMU support for Exynos3250
pm related maintenance
- imx:
new LS1021A SoC support
vybrid 610 global timer support
- integrator:
convert to using multiplatform configuration
- mediatek:
earlyprintk support for mt8127/mt8135
- meson:
meson8 soc and l2 cache controller support
- mvebu:
Armada 38x CPU hotplug support
drop support for prerelease Armada 375 Z1 stepping
extended suspend support, now works on Armada 370/XP
- omap:
hwmod related maintenance
prcm cleanup
- pxa:
initial pxa27x DT handling
- rockchip:
SMP support for rk3288
add cpu frequency scaling support
- shmobile:
r8a7740 power domain support
various small restart, timer, pci apmu changes
- sunxi:
Allwinner A80 (sun9i) earlyprintk support
- ux500:
power domain support
Overall, a significant chunk of changes, coming mostly from the usual
suspects: omap, shmobile, samsung and mvebu, all of which already
contain a lot of platform specific code in arch/arm"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (187 commits)
ARM: mvebu: use the cpufreq-dt platform_data for independent clocks
soc: integrator: Add terminating entry for integrator_cm_match
ARM: mvebu: add SDRAM controller description for Armada XP
ARM: mvebu: adjust mbus controller description on Armada 370/XP
ARM: mvebu: add suspend/resume DT information for Armada XP GP
ARM: mvebu: synchronize secondary CPU clocks on resume
ARM: mvebu: make sure MMU is disabled in armada_370_xp_cpu_resume
ARM: mvebu: Armada XP GP specific suspend/resume code
ARM: mvebu: reserve the first 10 KB of each memory bank for suspend/resume
ARM: mvebu: implement suspend/resume support for Armada XP
clk: mvebu: add suspend/resume for gatable clocks
bus: mvebu-mbus: provide a mechanism to save SDRAM window configuration
bus: mvebu-mbus: suspend/resume support
clocksource: time-armada-370-xp: add suspend/resume support
irqchip: armada-370-xp: Add suspend/resume support
ARM: add lolevel debug support for asm9260
ARM: add mach-asm9260
ARM: EXYNOS: use u8 for val[] in struct exynos_pmu_conf
power: reset: imx-snvs-poweroff: add power off driver for i.mx6
ARM: imx: temporarily remove CONFIG_SOC_FSL from LS1021A
...
The of_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some Tegra drivers might be compiled as kernel modules, and they need the
fuse information for initialization. One example is the GK20A Nouveau
driver. It needs the GPU speedo value to calculate frequency-voltage
table. So export the tegra_sku_info.
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This creates a new SoC bus driver for the ARM Integrator
family core modules to register the SoC bus and provide
sysfs info for the core module. We delete the corresponding
code from the Integrator machine and select this driver to
get a clean result.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
list_for_each_entry_safe() is necessary if list objects are deleted from
the list while traversing it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The of_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Don't call mutex_unlock() in the error patch if the mutex_lock() is not called.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Use list_first_entry_or_null() for first_region() and first_queue_range().
list_first_entry() expects the list is not empty, so first_region() and
first_queue_range() never return NULL.
Thus use list_first_entry_or_null() instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
Most of the new code is for the Keystone Navigator driver, which is
new base support that is going to be needed for their hardware
accelerated network driver and other units.
Most of the commits are for moving old code around from at91 and omap
for things that are done in device drivers nowadays.
- at91: move reset, poweroff, memory and clocksource code into drivers
directories
- socfpga: add edac driver (through arm-soc, as requested by Boris)
- omap: move omap-intc code to drivers/irqchip
- sunxi: added an RTC driver for sun6i
- omap: mailbox driver related changes
- keystone: support for the "Navigator" component
- versatile: new reboot, led and soc drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=POJD
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
Most of the new code is for the Keystone Navigator driver, which is
new base support that is going to be needed for their hardware
accelerated network driver and other units.
Most of the commits are for moving old code around from at91 and omap
for things that are done in device drivers nowadays.
- at91: move reset, poweroff, memory and clocksource code into
drivers directories
- socfpga: add edac driver (through arm-soc, as requested by Boris)
- omap: move omap-intc code to drivers/irqchip
- sunxi: added an RTC driver for sun6i
- omap: mailbox driver related changes
- keystone: support for the "Navigator" component
- versatile: new reboot, led and soc drivers"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (92 commits)
bus: arm-ccn: Fix spurious warning message
leds: add device tree bindings for register bit LEDs
soc: add driver for the ARM RealView
power: reset: driver for the Versatile syscon reboot
leds: add a driver for syscon-based LEDs
drivers/soc: ti: fix build break with modules
MAINTAINERS: Add Keystone Multicore Navigator drivers entry
soc: ti: add Keystone Navigator DMA support
Documentation: dt: soc: add Keystone Navigator DMA bindings
soc: ti: add Keystone Navigator QMSS driver
Documentation: dt: soc: add Keystone Navigator QMSS bindings
rtc: sunxi: Depend on platforms sun4i/sun7i that actually have the rtc
rtc: sun6i: Add sun6i RTC driver
irqchip: omap-intc: remove unnecessary comments
irqchip: omap-intc: correct maximum number or MIR registers
irqchip: omap-intc: enable TURBO idle mode
irqchip: omap-intc: enable IP protection
irqchip: omap-intc: remove unnecesary of_address_to_resource() call
irqchip: omap-intc: comment style cleanup
irqchip: omap-intc: minor improvement to omap_irq_pending()
...
This adds a SoC driver to be used by the ARM RealView
reference boards. We create the "versatile" directory to hold
the different ARM reference designs as per the pattern of the
clk directory layout. The driver utilze the syscon to get to
the register needed. After this we can use sysfs to get at
some SoC properties on RealView DT variants like this:
> cd /sysbus/soc/devices/soc0
> ls
board family machine power subsystem
build fpga manufacturer soc_id uevent
> cat family
Versatile
> cat fpga
Multi-layer AXI
> cat board
HBI-0147
> cat build
03
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
drivers/soc/Kconfig
drivers/soc/Makefile
The Keystone Navigator DMA driver sets up the dma channels and flows for
the QMSS(Queue Manager SubSystem) who triggers the actual data movements
across clients using destination queues. Every client modules like
NETCP(Network Coprocessor), SRIO(Serial Rapid IO) and CRYPTO
Engines has its own instance of packet dma hardware. QMSS has also
an internal packet DMA module which is used as an infrastructure
DMA with zero copy.
Initially this driver was proposed as DMA engine driver but since the
hardware is not typical DMA engine and hence doesn't comply with typical
DMA engine driver needs, that approach was naked. Link to that
discussion -
https://lkml.org/lkml/2014/3/18/340
As aligned, now we pair the Navigator DMA with its companion Navigator
QMSS subsystem driver.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The QMSS (Queue Manager Sub System) found on Keystone SOCs is one of
the main hardware sub system which forms the backbone of the Keystone
Multi-core Navigator. QMSS consist of queue managers, packed-data structure
processors(PDSP), linking RAM, descriptor pools and infrastructure
Packet DMA.
The Queue Manager is a hardware module that is responsible for accelerating
management of the packet queues. Packets are queued/de-queued by writing or
reading descriptor address to a particular memory mapped location. The PDSPs
perform QMSS related functions like accumulation, QoS, or event management.
Linking RAM registers are used to link the descriptors which are stored in
descriptor RAM. Descriptor RAM is configurable as internal or external memory.
The QMSS driver manages the PDSP setups, linking RAM regions,
queue pool management (allocation, push, pop and notify) and descriptor
pool management. The specifics on the device tree bindings for
QMSS can be found in:
Documentation/devicetree/bindings/soc/keystone-navigator-qmss.txt
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
since commit 31964ffebb ("tty: serial: msm: Remove direct access to GSBI")'
serial hangs if earlyprintk are enabled.
This hang is noticed only when the GSBI driver is probed and all the
earlyprintks before gsbi probe are seen on the console.
The reason why it hangs is because GSBI driver disables hclk in its
probe function without realizing that the serial IP might be in use by
a bootconsole. As gsbi driver disables the clock in probe the
bootconsole locks up.
Turning off hclk's could be dangerous if there are system components
like earlyprintk using the hclk.
This patch fixes the issue by delegating the clock management to
probe and remove functions in gsbi rather than disabling the clock in probe.
More detailed problem description can be found here:
http://www.spinics.net/lists/linux-arm-msm/msg10589.html
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This commit converts the PMC support code to a platform driver. Because
the boot process needs to call into this driver very early, also set up
a minimal environment via an early initcall.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather than rely on explicit initialization order called from SoC setup
code, use a plain initcall and rely on initcall ordering to take care of
dependencies.
This driver exposes some functionality (querying the chip ID) needed at
very early stages of the boot process. An early initcall is good enough
provided that some of the dependencies are deferred to later stages. To
make sure any abuses are easily caught, output a warning message if the
chip ID is queried while it can't be read yet.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Subsequent patches will move some of the initialization code from SoC
setup code to regular initcalls. To prevent breakage on other SoCs in
multi-platform builds, these initcalls need to check that they indeed
run on Tegra.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra fuse header's dummy functions for the case where Tegra20 is
disabled are inconsistent with the correct prototypes, and have some
syntax errors. Fix these. While at it, fix the indentation level of
the dummy function bodies.
Fixes: 783c8f4c84 ("soc/tegra: Add efuse driver for Tegra")
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra20 fuse driver is the only user of tegra_apb_readl_using_dma().
Therefore we can simply the code by incorporating the APB DMA handling into
the driver directly. tegra_apb_writel_using_dma() is dropped because there
are no users.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement fuse driver for Tegra20, Tegra30, Tegra114 and Tegra124. This
replaces functionality previously provided in arch/arm/mach-tegra, which
is removed in this patch.
While at it, move the only user of the global tegra_revision variable
over to tegra_sku_info.revision and export tegra_fuse_readl() to allow
drivers to read calibration fuses.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The match tables must be zero-terminated, and Kbuild now helpfully
fails to link the kernel if that isn't the case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The GSBI (General Serial Bus Interface) driver controls the overarching
configuration of the shared serial bus infrastructure on APQ8064, IPQ8064, and
earlier QCOM processors. The GSBI supports UART, I2C, SPI, and UIM
functionality in various combinations.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Based on earlier thread "https://lkml.org/lkml/2013/10/7/662" and
discussion at Kernel Summit'2013, it was agreed to create
'driver/soc' for drivers which are quite SOC specific.
Further discussion on the subject is in response to
the earlier version of the patch is here:
http://lwn.net/Articles/588942/
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Maxime Ripard