rc-core kapi uses nanoseconds for infrared durations for receiving, and
microseconds for sending. The uapi already uses microseconds for both,
so this patch does not change the uapi.
Infrared durations do not need nanosecond resolution. IR protocols do not
have durations shorter than about 100 microseconds. Some IR hardware offers
250 microseconds resolution, which is sufficient for most protocols.
Better hardware has 50 microsecond resolution and is enough for every
protocol I am aware off.
Unify on microseconds everywhere. This simplifies the code since less
conversion between microseconds and nanoseconds needs to be done.
This affects:
- rx_resolution member of struct rc_dev
- timeout member of struct rc_dev
- duration member in struct ir_raw_event
Cc: "Bruno Prémont" <bonbons@linux-vserver.org>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Patrick Lerda <patrick9876@free.fr>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: "David Härdeman" <david@hardeman.nu>
Cc: Benjamin Valentin <benpicco@googlemail.com>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The IR device on Hi3796CV300 SoC is mostly same as hix5hd2, except the
following two things.
- IR_CLK offset is 0x60 instead of 0x48.
- It needs to set an extra bit in IR_ENABLE register to enable IR.
The following changes are made to deal with them.
- Define a SoC specific data to accommodate IR_CLK offset and the flag
telling requirement of extra enable bit.
- Create function hix5hd2_ir_enable() to handle IR enabling. The original
hix5hd2_ir_enable() is all about managing IR clock, so gets renamed
to hix5hd2_ir_clk_enable().
- Device table hix5hd2_ir_table[] gets moved forward, as it's being
used by hix5hd2_ir_probe() now.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 101 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190113.822954939@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This can be done with c99 initializers, which makes the code cleaner
and more transparent. It does require gcc 4.6, because of this bug
in earlier versions:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=10676
Since commit cafa0010cd ("Raise the minimum required gcc version to
4.6"), this is the case.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Return code of clk_prepare_enable() is ignored in many places.
The patch adds error handling for all of them.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
RC_TYPE is confusing and it's just the protocol. So rename it.
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When an ir-spi is registered, you get this message.
rc rc0: Unspecified device as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
"Unspecified device" refers to input_name, which makes no sense for IR
TX only devices. So, rename to device_name.
Also make driver_name const char* so that no casts are needed anywhere.
Now ir-spi reports:
rc rc0: IR SPI as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver type can be assigned immediately when an RC device
requests to the framework to allocate the device.
This is an 'enum rc_driver_type' data type and specifies whether
the device is a raw receiver or scancode receiver. The type will
be given as parameter to the rc_allocate_device device.
Change accordingly all the drivers calling rc_allocate_device()
so that the device type is specified during the rc device
allocation. Whenever the device type is not specified, it will be
set as RC_DRIVER_SCANCODE which was the default '0' value.
Suggested-by: Sean Young <sean@mess.org>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
unknown and other are for IR protocols for which we have no decoder,
so the raw IR drivers have no chance of generating them. cec is not
an IR protocol.
Signed-off-by: Sean Young <sean@mess.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The clock of IR can be provided by the clock provider and controlled
by common clock framework APIs.
Signed-off-by: Ruqiang Ju <juruqiang@huawei.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver doesn't claim the IR transmitter to be wakeup source. It
even disables the clock and the IR during suspend-resume cycle.
This patch removes yet another misuse of IRQF_NO_SUSPEND.
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Guoxiong Yan <yanguoxiong@huawei.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Building for avr32 leads the following build warning:
drivers/media/rc/ir-hix5hd2.c:221: warning: passing argument 1 of 'IS_ERR' discards qualifiers from pointer target type
drivers/media/rc/ir-hix5hd2.c:222: warning: passing argument 1 of 'PTR_ERR' discards qualifiers from pointer target type
devm_ioremap_resource() returns void __iomem *, so change 'base' definition
accordingly.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
[mchehab@osg.samsung.com: fix a merge conflict at adv7604.c]
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change CONFIG_PM to CONFIG_PM_SLEEP to solve
warning: 'hix5hd2_ir_suspend' & 'hix5hd2_ir_resume' defined but not used
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While not all archs have readl_relaxed, we need to add a hack at the
driver to allow it to COMPILE_TEST on all archs:
drivers/media/rc/ir-hix5hd2.c: In function ‘hix5hd2_ir_config’:
drivers/media/rc/ir-hix5hd2.c💯2: error: implicit declaration of function ‘readl_relaxed’ [-Werror=implicit-function-declaration]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
IR transmitter driver for Hisilicon hix5hd2 soc
By default all protocols are disabled.
For example nec decoder can be enabled by either
1. ir-keytable -p nec
2. echo nec > /sys/class/rc/rc0/protocols
See see Documentation/ABI/testing/sysfs-class-rc
[mchehab@osg.samsung.com: Add a fixup for the driver to compile on
archs that don't provide writel_relaxed() macro]
Signed-off-by: Guoxiong Yan <yanguoxiong@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sean Young