When CPUs start and stop the watchdog, they manipulate shared data
that is normally protected by the lock. Other CPUs can be running
concurrently at this time, so it's a good idea to use locking here
to be on the safe side.
Remove the barrier which is undocumented and didn't do anything.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When the SMP detector finds other CPUs stuck, it iterates over
them and marks them as stuck. This pulls them out of the pending
mask and allows the detector to continue with remaining good
CPUs (if nmi_watchdog=panic is not enabled).
The code to dothat was buggy because when setting a CPU stuck,
if the pending mask became empty, it resets it to keep the
watchdog running. However the iterator will continue to run
over the new pending mask and mark remaining good CPUs sas stuck.
Fix this by doing it with cpumask bitwise operations.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When the watchdog decides to panic, it takes the lock and double
checks everything (to avoid races with the CPU being unstuck or
panic()ed by something else).
The exit label was misplaced and would result in all-CPUs backtrace
and watchdog panic even in the case that the condition was found to be
resolved.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some code can go into a tight loop calling touch_nmi_watchdog (e.g.,
stop_machine CPU hotplug code). This can cause contention on watchdog
locks particularly if all CPUs with watchdog enabled are spinning in
the loops.
Avoid this storm of activity by running the watchdog timer callback
from this path if we have exceeded the timer period since it was last
run.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Hard-disable interrupts before taking the lock, which prevents
soft-NMI re-entrancy and therefore can prevent deadlocks.
- Use raw_ variants of local_irq_disable to avoid irq debugging.
- When the lock is contended, spin at low SMT priority, using
loads only, and with interrupts enabled (where possible).
Some stalls have been noticed at high loads that go away with improved
locking. There should not be so much locking contention in the first
place (which is addressed in a subsequent patch), but locking should
still be improved.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When the NMI IPI lock is contended, spin at low SMT priority, using
loads only, and with interrupts enabled (where possible). This
improves behaviour under high contention (e.g., a system crash when
a number of CPUs are trying to enter the debugger).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 05a4a95279 ("kernel/watchdog: split up config options"),
CONFIG_LOCKUP_DETECTOR was split into two separate config options,
CONFIG_HARDLOCKUP_DETECTOR and CONFIG_SOFTLOCKUP_DETECTOR.
Our defconfigs still have CONFIG_LOCKUP_DETECTOR=y, but that is no longer
user selectable, and we don't mention the new options, so we end up with
none of them enabled.
So update the defconfigs to turn on the new SOFT and HARD options, the
end result being the same as what we had previously.
Fixes: 05a4a95279 ("kernel/watchdog: split up config options")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, we use the opal call opal_slw_set_reg() to inform the
Sleep-Winkle Engine (SLW) to restore the contents of some of the
Hypervisor state on wakeup from deep idle states that lose full
hypervisor context (characterized by the flag
OPAL_PM_LOSE_FULL_CONTEXT).
However, the current code has a bug in that if opal_slw_set_reg()
fails, we don't disable the use of these deep states (winkle on
POWER8, stop4 onwards on POWER9).
This patch fixes this bug by ensuring that if programing the
sleep-winkle engine to restore the hypervisor states in
pnv_save_sprs_for_deep_states() fails, then we exclude such states by
clearing the OPAL_PM_LOSE_FULL_CONTEXT flag from
supported_cpuidle_states. As a result POWER8 will be prevented from
using winkle for CPU-Hotplug, and POWER9 will put the offlined CPUs to
the default stop state when available.
Further, we ensure in the initialization of the cpuidle-powernv driver
to only include those states whose flags are present in
supported_cpuidle_states, thereby skipping OPAL_PM_LOSE_FULL_CONTEXT
states when they have been disabled due to stop-api failure.
Fixes: 1e1601b38e ("powerpc/powernv/idle: Restore SPRs for deep idle
states via stop API.")
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On 64-bit book3s, with the hash MMU, we currently define the kernel
virtual space (vmalloc, ioremap etc.), to be 16T in size. This is a
leftover from pre v3.7 when our user VM was also 16T.
Of that 16T we split it 50/50, with half used for PCI IO and ioremap
and the other 8T for vmalloc.
We never bothered to make it any bigger because 8T of vmalloc ought to
be enough for anybody. But it turns out that's not true, the per cpu
allocator wants large amounts of vmalloc space, not to make large
allocations, but to allow a large stride between allocations, because
we use pcpu_embed_first_chunk().
With a bit of juggling we can increase the entire kernel virtual space
to 64T. The only real complication is the check of the address in the
SLB miss handler, see the comment in the code.
Although we could continue to split virtual space 50/50 as we do now,
no one seems to be running out of PCI IO or ioremap space. So instead
keep that as 8T, and use the remaining 56T for vmalloc.
In future we should be able to increase the kernel virtual space to
512T, the code already supports that, it just needs testing on older
hardware.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
There is a comment in slb_allocate() referring to the load of
paca->vmalloc_sllp, but it's several lines prior in the assembly.
We're about to change this code, and we want to add another comment,
so move the comment immediately prior to the instruction it's talking
about.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently KERN_IO_START is defined as:
#define KERN_IO_START (KERN_VIRT_START + (KERN_VIRT_SIZE >> 1))
Although it looks like a constant, both the components are actually
variables, to allow us to have a different value between Radix and
Hash with a single kernel.
However that still requires both Radix and Hash to place the kernel IO
region at the same location relative to the start and end of the
kernel virtual region (namely 1/2 way through it), and we'd like to
change that.
So split KERN_IO_START out into its own variable, and initialise it
for Radix and Hash. In the medium term we should be able to
reconsolidate this, by doing a more involved rearrangement of the
location of the regions.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds powernv_get_random_darn() which utilises the darn instruction,
introduced in ISA v3.0/POWER9.
The darn instruction can potentially return an error, which is supported
by the get_random_seed() API, in normal usage if we see an error we just
return that to the caller.
However when detecting whether darn is functional at boot we try up to
10 times, before deciding that darn doesn't work and failing the
registration of get_random_seed(). That way an intermittent failure
at boot doesn't deprive the system of randomness until the next reboot.
Signed-off-by: Matt Brown <matthew.brown.dev@gmail.com>
[mpe: Move init into a function, tweak change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit d300627c6a ("powerpc/6xx: Handle DABR match before calling
do_page_fault") breaks non 6xx platforms.
Failed to execute /init (error -14)
Starting init: /bin/sh exists but couldn't execute it (error -14)
Kernel panic - not syncing: No working init found. Try passing init= ...
CPU: 0 PID: 1 Comm: init Not tainted 4.13.0-rc3-s3k-dev-00143-g7aa62e972a56 #56
Call Trace:
panic+0x108/0x250 (unreliable)
rootfs_mount+0x0/0x58
ret_from_kernel_thread+0x5c/0x64
Rebooting in 180 seconds..
This is because in handle_page_fault(), the call to do_page_fault() has been
mistakenly enclosed inside an #ifdef CONFIG_6xx
Fixes: d300627c6a ("powerpc/6xx: Handle DABR match before calling do_page_fault")
Brown-paper-bag-to-be-worn-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
P9 has support for PCI peer-to-peer, enabling a device to write in the
MMIO space of another device directly, without interrupting the CPU.
This patch adds support for it on powernv, by adding a new API to be
called by drivers. The pnv_pci_set_p2p(...) call configures an
'initiator', i.e the device which will issue the MMIO operation, and a
'target', i.e. the device on the receiving side.
P9 really only supports MMIO stores for the time being but that's
expected to change in the future, so the API allows to define both
load and store operations.
/* PCI p2p descriptor */
#define OPAL_PCI_P2P_ENABLE 0x1
#define OPAL_PCI_P2P_LOAD 0x2
#define OPAL_PCI_P2P_STORE 0x4
int pnv_pci_set_p2p(struct pci_dev *initiator, struct pci_dev *target,
u64 desc)
It uses a new OPAL call, as the configuration magic is done on the
PHBs by skiboot.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
[mpe: Drop unrelated OPAL calls, s/uint64_t/u64/, minor formatting]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the decrementer wraps again and de-asserts the decrementer
exception while hard-disabled, __check_irq_replay() has a test to
notice the wrap when interrupts are re-enabled.
The decrementer check must be done when clearing the PACA_IRQ_HARD_DIS
flag, not when the PACA_IRQ_DEC flag is tested. Previously this worked
because the decrementer interrupt was always the first one checked
after clearing the hard disable flag, but HMI check was moved ahead of
that, which introduced this bug.
This can cause a missed decrementer interrupt if we soft-disable
interrupts then take an HMI which is recorded in irq_happened, then
hard-disable interrupts for > 4s to wrap the decrementer.
Fixes: e0e0d6b739 ("powerpc/64: Replay hypervisor maintenance interrupt first")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 DD2 PMU can stop after a state-loss idle in some conditions.
A solution is to set then clear MMCRA[60] after wake from state-loss
idle. MMCRA[60] is a non-architected bit, see the user manual for
details.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have a whole pile of unused code to maintain the ACOP register,
allocate coprocessor PIDs and handle ACOP faults. This mechanism
was used for the HFI adapter on POWER7 which is dead and gone and
whose driver never went upstream. It was used on some A2 core based
stuff that also never saw the light of day.
Take out all that code.
There is still some POWER8 coprocessor code that uses icswx but it's
kernel only and thus doesn't use any of that infrastructure.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When hitting below a VM_GROWSDOWN vma (typically growing the stack),
we check whether it's a valid stack-growing instruction and we
check the distance to GPR1. This is largely open coded with lots
of comments, so move it out to a helper.
While at it, make store_update_sp a boolean.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the first iteration returns VM_FAULT_MAJOR but the second
one doesn't, we fail to account the fault as a major fault.
This fixes it and brings the code in line with x86.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move out the code that sets FAULT_FLAG_WRITE so the block that check
access permissions can be extracted. While at it also set
FAULT_FLAG_INSTRUCTION which will be used for protection keys.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Do the check before we re-enable interrupts and clean the code
up a bit.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This has a page of comment explaining what's going on right in
the middle of do_page_fault() which makes things a bit hard to
follow. Move it to a helper instead. Also do the test earlier
as there's no point waiting until after we found the VMA.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
No need to break those lines, they aren't that long
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It makes do_page_fault() more readable. No functional change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
First, handle the normal retry failure in do_page_fault itself,
since it's a simple return statement. That allows us to remove
the "continue" special return code from mm_fault_error().
Once that's done, we can have an implementation much closer to
x86 where we only call mm_fault_error() if VM_FAULT_ERROR is set
and directly return.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of goto labels, instead call those functions and return.
This gets us closer to x86 and allows us to shring do_page_fault()
even more.
The main difference with x86 is that those function return a value
which we then return from do_page_fault(). That value is our
return value from do_page_fault() which we use to generate
kernel faults.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We currently test for is_exec and DSISR_PROTFAULT but that doesn't
make sense as this is the wrong error bit to test for an execute
permission failure.
In fact, we had code that would return early if we had an exec
fault in kernel mode so I think that was just dead code anyway.
Finally the location of that test is awkward and prevents further
simplifications.
So instead move that test into a helper along with the existing
early test for kernel exec faults and out of range accesses,
and put it all in a "bad_kernel_fault()" helper. While at it
test the correct error bits.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we moved the exception state handling to a wrapper, we can
just directly return rather than "goto bail"
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A bad page fault is when the HW signals an error such as a bad
copy/paste, an AMO error, or some other type of error that will
not be fixed by updating the PTE.
Use a helper page_fault_is_bad() to check for bad page faults thus
removing the per-processor family open-coding in __do_page_fault()
and trigger a SIGBUS rather than a SIGSEGV which is more appropriate.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There's no point looking for the VMA etc.. when we already know
we are going to fail.
This adds some code to set "code" for the si_code but that will
be gone in subsequent patches.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Define a common page_fault_is_write() helper and use it
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This uses the newly defined constants for this rather than open-coded
numbers. There is a side effect on 64-bit which is to pass through
some of the new P9 bits which we didn't before.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We test a number of bits from DSISR/SRR1 before deciding
to call hash_page(). If any of these is set, we go directly
to do_page_fault() as the bit indicate a fault that needs
to be handled there (no hashing needed).
This updates the current open-coded masks to use the new
DSISR definitions.
This *does* change the masks actually used in two ways:
- We used to test various bits that were defined as "always 0"
in the architecture and could be repurposed for something
else. From now on, we just ignore such bits.
- We were missing some new bits defined on P9
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This updates the definitions for the various DSISR bits to
match both some historical stuff and to match new bits on
POWER9.
In addition, we define some masks corresponding to the "bad"
faults on Book3S, and some masks corresponding to the bits
that match between DSISR and SRR1 for a DSI and an ISI.
This comes with a small code update to change the definition
of DSISR_PGDIRFAULT which becomes DSISR_PRTABLE_FAULT to
match architecture 3.0B
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On legacy 6xx 32-bit procesors, we checked for the DABR match bit
in DSISR from do_page_fault(), in the middle of a pile of ifdef's
because all other CPU types do it in assembly prior to calling
do_page_fault. Fix that.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Add #ifdef CONFIG_6xx]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
of_irq_to_resource() has recently been fixed to return negative error #'s
along with 0 in case of failure, however the Freescale MPC832x RDB board
code still only regards 0 as a failure indication -- fix it up.
Fixes: 7a4228bbff ("of: irq: use of_irq_get() in of_irq_to_resource()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
By filtering the relevant SRR1 bits in the assembly rather than
in do_page_fault() itself, we avoid a conditional branch (since we
already come from different path for data and instruction faults).
This will allow more simplifications later
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This will allow simplifying the returns from do_page_fault
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We do that because it's used by THP pmd collapsing, so use
instead a dedicated flush function.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At the moment we have to rather sub-optimal flushing behaviours:
- flush_tlb_mm() will flush the PWC which is unnecessary (for example
when doing a fork)
- A large unmap will call flush_tlb_pwc() multiple times causing us
to perform that fairly expensive operation repeatedly. This happens
often in batches of 3 on every new process.
So we change flush_tlb_mm() to only flush the TLB, and we use the
existing "need_flush_all" flag in struct mmu_gather to indicate
that the PWC needs flushing.
Unfortunately, flush_tlb_range() still needs to do a full flush
for now as it's used by the THP collapsing. We will fix that later.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The PWC flush only needs a single set call, just like the
full (RIC=2) flush.
This will allow us to get rid of the dedicated _tlbiel_pwc()
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Replace the __this_cpu_read() with raw_cpu_read() in
iommu_range_alloc(). Otherwise we get a warning about using
__this_cpu_read() in preemptible code:
BUG: using __this_cpu_read() in preemptible
caller is iommu_range_alloc+0xa8/0x3d0
Preemption doesn't need to be disabled since according to the comment
any CPU can safely use any IOMMU pool.
Signed-off-by: Victor Aoqui <victora@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we use the stop-api provided by the firmware to program the
SLW engine to restore the values of hypervisor resources that get lost
on deeper idle states (such as winkle). Since the deep states were
only used for CPU-Hotplug on POWER8 systems, we would program the LPCR
to have the PECE1 bit since Hotplugged CPUs shouldn't be spuriously
woken up by decrementer.
On POWER9, some of the deep platform idle states such as stop4 can be
used in cpuidle as well. In this case, we want the CPU in stop4 to be
woken up by the decrementer when some timer on the CPU expires.
In this patch, we program the stop-api for LPCR with PECE1
bit cleared only when we are offlining the CPU and set it
back once the CPU is online.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The stop4 idle state on POWER9 is a deep idle state which loses
hypervisor resources, but whose latency is low enough that it can be
exposed via cpuidle.
Until now, the deep idle states which lose hypervisor resources (eg:
winkle) were only exposed via CPU-Hotplug. Hence currently on wakeup
from such states, barring a few SPRs which need to be restored to
their older value, rest of the SPRS are reinitialized to their values
corresponding to that at boot time.
When stop4 is used in the context of cpuidle, we want these additional
SPRs to be restored to their older value, to ensure that the context
on the CPU coming back from idle is same as it was before going idle.
In this patch, we define a SPR save area in PACA (since we have used
up the volatile register space in the stack) and on POWER9, we restore
SPRN_PID, SPRN_LDBAR, SPRN_FSCR, SPRN_HFSCR, SPRN_MMCRA, SPRN_MMCR1,
SPRN_MMCR2 to the values they had before entering stop.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The watchdog soft-NMI exception stack setup loads a stack pointer
twice, which is an obvious error. It ends up using the system reset
interrupt (true-NMI) stack, which is also a bug because the watchdog
could be preempted by a system reset interrupt that overwrites the
NMI stack.
Change the soft-NMI to use the "emergency stack". The current kernel
stack is not used, because of the longer-term goal to prevent
asynchronous stack access using soft-disable.
Fixes: 2104180a53 ("powerpc/64s: implement arch-specific hardlockup watchdog")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZapWhAAoJEHm+PkMAQRiGKb0IAJM6b7SbWaw69Og7+qiFB+zZ
xp29iXqbE9fPISC6a5BRQV1ONjeDM6opGixGHqGC8Hla6k2IYz25VDNoF8wd0MXN
cz/Ih20vd3C5afxXGe5cTT8lsPAlV0mWXxForlu6j8jPeL62FPfq6RhEkw7AcrYL
yfYy3k3qSdOrrvBdII0WAAUi46UfIs+we9BQgbsMbkHOiqV2K0MOrzKE84Xbgepq
RAy2xg6P4b4+hTx8xTrYc1MXwpnqjRc0oJ08gdmiwW3AOOU7LxYFn7zDkLPWi9Rr
g4x6r4YhBTGxT4wNvovLIiqd9QFs//dMCuPWYwEtTICG48umIqqq24beQ0mvCdg=
=08Ic
-----END PGP SIGNATURE-----
Merge tag 'v4.13-rc1' into fixes
The fixes branch is based off a random pre-rc1 commit, because we had
some fixes that needed to go in before rc1 was released.
However we now need to fix some code that went in after that point, but
before rc1, so merge rc1 to get that code into fixes so we can fix it!
Nicholas Piggin