Finally we have a proper infrastructure to generate the modaliases
automatically, let's move to hda_device_id from the legacy
hda_codec_preset that contains basically the same information.
The patch function hook is stored in driver_data field, which is long,
and we need an explicit cast. Other than that, the conversion is
mostly straightforward. Each entry is even simplified using a macro,
and the lengthy (and error-prone) manual modaliases got removed.
As a result, we achieved a quite good diet:
14 files changed, 407 insertions(+), 595 deletions(-)
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent commit [7fbe824a0f0e: ALSA: hda - Update mixer name for the
lower codec address] tried to improve the mixer chip name assignment
in the order of codec address. However, this fix was utterly bogus;
it checks the field set in each codec, thus this value is reset at
each codec creation, of course. For really handling this priority,
the assignment has to be remembered in the common place, namely in
hda_bus, instead of hda_codec.
Fixes: 7fbe824a0f ('ALSA: hda - Update mixer name for the lower codec address')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In most cases, we prefer the onboard codec as the primary device, thus
it's better to set it as the mixer name. Currently, however, the
mixer name is updated per the device instantiation order, and user
gets often HDMI/DP or other seen as a mixer chip name. Also, if a
codec name is renamed by the driver, the old chip name might be left
still as the mixer name.
This patch addresses these issues by remembering the chip address that
was referred as the mixer name. When a codec with the same or lower
address gives its name, renew the mixer name accordingly, as it's
either the update of the codec name or we get likely the more
appropriate chip as the reference.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few multiple codec drivers do renaming the chip_name string but all
these are open-coded and some of them have even no error check. Let's
make common helpers to do it properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that we have introduced the core fns we should make hda use these
helpers
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few helper functions to convert the pin information to strings have
been exported with assumption that they were used by other drivers.
But they are referred only in the proc interface in the end.
Let's make them local so that we can get rid of a few exports.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable runtime PM of the HDMI audio codec on the latest Intel platforms.
So the HD-A controller or HDMI codec can suspend when idle timeout by
default and release the GFX power well.
The patch influences HSW/BDW/BYT/BSW/SKL. Eariler platforms and third
party analog codecs will not be influenced.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Building errors reported such as below when 'CONFIG_INPUT=m':
...undefined reference to `input_xxx'...
Here change to enable SND_JACK selectively to fix the issue.
Also remove the config 'SND_HDA_INPUT_JACK' which won't be
used anymore.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Originally hda_bus takes its own ops (hda_bus_ops) to allow different
controller drivers giving individual implementations of PCM
attachment, etc. But this never happened and we finally merged both
codec and controller helper codes. Thus there is no merit to keep the
indirect accesses to functions via hda_bus_ops.
This patch replaces these calls with the direct local function calls
for simplification.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... and replace with the existing hda-core helper codes.
This reduces lots of lines, finally.
Since struct hda_bus is now embedded into struct azx,
snd_hda_bus_new() is moved and expanded from hda_codec.c to
hda_controller.c, accordingly. Also private_free bus ops and
private_data field are removed because we no longer need to point azx
object from bus (we can use container_of())
The spin locks are consolidated into the single one, bus->reg_lock.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
One less redirection again. This also requires the change of the call
order in the toplevel divers. Namely, the bus has to be created at
first before other initializations since the memory allocation ops are
called through bus object now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... and drop bus->rirb_error flag. This makes the code simpler.
We treat -EAGAIN from get_response ops as a special meaning: it allows
the caller to retry after bus reset.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, snd_hdac_power_up()/down() helpers checks whether the codec
is being in pm (suspend/resume), and skips the call of runtime get/put
during it. This is needed as there are lots of power up/down
sequences called in the paths that are also used in the PM itself. An
example is found in hda_codec.c::codec_exec_verb(), where this can
power up the codec while it may be called again in its power up
sequence, too.
The above works in most cases, but sometimes we really want to wait
for the real power up. For example, the control element get/put may
want explicit power up so that the value change is assured to reach to
the hardware. Using the current snd_hdac_power_up(), however,
results in a race, e.g. when it's called during the runtime suspend is
being performed. In the worst case, as found in patch_ca0132.c, it
can even lead to the deadlock because the code assumes the power up
while it was skipped due to the check above.
For dealing with such cases, this patch makes snd_hdac_power_up() and
_down() to two variants: with and without in_pm flag check. The
version with pm flag check is named as snd_hdac_power_up_pm() while
the version without pm flag check is still kept as
snd_hdac_power_up(). (Just because the usage of the former is fewer.)
Then finally, the patch replaces each call potentially done in PM with
the new _pm() variant.
In theory, we can implement a unified version -- if we can distinguish
the current context whether it's in the pm path. But such an
implementation is cumbersome, so leave the code like this a bit messy
way for now...
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96271
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This merges the support of regmap in HD-audio infrastructure.
Many in-house cache codes in HD-audio driver are relaced with the
more standard regmap base now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just forgotten to remove. It's now in sound/hdaudio.h.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the previous patches, this patch converts also to the regmap, at
this time, the cached verb writes are the target. But this conversion
needs a bit more caution than before.
- In the old code, we just record any verbs as is, and restore them at
resume. For the regmap scheme, this doesn't work, since a few verbs
like AMP or DIGI_CONVERT are asymmetrical. Such verbs are converted
either to the dedicated function (snd_hda_regmap_xxx_amp()) or
changed to the unified verb.
- Some verbs have to be declared as vendor-specific ones before
accessing via regmap.
Also, the minor optimization with codec->cached_write flag is dropped
in a few places, as this would confuse the operation. Further
optimizations will be brought in the later patches, if any.
This conversion ends up with a drop of significant amount of codes,
mostly the helper codes that are no longer used.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The amp hash table was used for recording the cached reads of some
capability values like pin caps or amp caps. Now all these are moved
to regmap as well.
One addition to the regmap helper is codec->caps_overwriting flag.
This is set in snd_hdac_override_parm(), and the regmap helper accepts
any register while this flag is set, so that it can overwrite even the
read-only verb like AC_VERB_PARAMETERS. The flag is cleared
immediately in snd_hdac_override_parm(), as it's a once-off flag.
Along with these changes, the no longer needed amp hash and relevant
fields are removed from hda_codec struct now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Let's start converting the access functions to regmap.
The first one is the simplest, just converting the codec parameter
read helper function snd_hda_param_read().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds an infrastructure to support regmap-based verb
accesses. Because o the asymmetric nature of HD-audio verbs,
especially the amp verbs, we need to translate the verbs as a sort of
pseudo registers to be mapped uniquely in regmap.
In this patch, a pseudo register is built from the NID, the
AC_VERB_GET_* and 8bit parameters, i.e. almost in the form to be sent
to HD-audio bus but without codec address field. OTOH, for writing,
the same pseudo register is translated to AC_VERB_SET_* automatically.
The AC_VERB_SET_AMP_* verb is re-encoded from the corresponding
AC_VERB_GET_AMP_* verb and parameter at writing.
Some verbs has a single command for read but multiple for writes. A
write for such a verb is split automatically to multiple verbs.
The patch provides also a few handy helper functions. They are
designed to be accessible even without regmap. When no regmap is set
up (e.g. before the codec device instantiation), the direct hardware
access is used. Also, it tries to avoid the unnecessary power-up.
The power up/down sequence is performed only on demand.
The codec driver needs to call snd_hdac_regmap_exit() and
snd_hdac_regmap_exit() at probe and remove if it wants the regmap
access.
There is one flag added to hdac_device. When the flag lazy_cache is
set, regmap helper ignores a write for a suspended device and returns
as if it was actually written. It reduces the hardware access pretty
much, e.g. when adjusting the mixer volume while in idle. This
assumes that the driver will sync the cache later at resume properly,
so use it carefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the driver is unloaded before the codec is bound, it still keeps
the runtime PM refcount up, and results in the unbalance. This patch
covers these cases by introducing a flag indicating the runtime PM
initialization and handling the codec registration procedure more
properly. It also fixes the missing input beep device as a gratis,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now some codes and functionalities of hda_codec struct are moved to
hdac_device struct. A few basic attributes like the codec address,
vendor ID number, FG numbers, etc are moved to hdac_device, and they
are accessed like codec->core.addr. The basic verb exec functions are
moved, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few basic codes for communicating over HD-audio bus are moved to
struct hdac_bus now. It has only command and get_response ops in
addition to the unsolicited event handling.
Note that the codec-side tracing support is disabled temporarily
during this transition due to the code shuffling. It will be
re-enabled later once when all pieces are settled down.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Define the common hd-audio driver and device types to bind over
snd_hda_bus_type publicly. This allows to implement other type of
device and driver code over hd-audio bus.
Now both struct hda_codec and struct hda_codec_driver inherit these
new struct hdac_device and struct hdac_driver, respectively.
The bus registration is done in subsys_initcall() to assure it
before any other driver registrations.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
David suggested that the name "power_mgmt" is too ambiguous. Rename
the flag with a bit clearer one "power_save_node".
Also, add the corresponding description to HD-Audio.txt, too.
Reported-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch enables the finer power state control of each widget
depending on the jack plug state and streaming state in addition to
the existing power_down_unused power optimization. The new feature is
enabled only when codec->power_mgmt flag is set.
Two new flags, pin_enabled and stream_enabled, are introduced in
nid_path struct for marking the two individual power states: the pin
plug/unplug and DAC/ADC stream, respectively. They can be set
statically in case they are static routes (e.g. some mixer paths),
too.
The power up and down events for each pin are triggered via the
standard hda_jack table. The call order is hard-coded, relying on the
current implementation of jack event chain (a la FILO/stack order).
One point to be dealt carefully is that DAC/ADC cannot be powered
on/off while streaming. They are pinned as long as the stream is
running. For controlling the power of DAC/ADC, a new patch_ops is
added. The generic parser provides the default callback for that.
As of this patch, only IDT/Sigmatel codec driver enables the flag.
The support on other codecs will follow.
An assumption we made in this code is that the widget state (e.g. amp,
pinctl, connections) remains after the widget power transition (not
about FG power transition). This is true for IDT codecs, at least.
But if the widget state is lost at widget power transition, we'd need
to implement additional code to sync the cached amp/verbs for the
specific NID.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver shutdown ops is simpler than registering reboot notifier
manually. There should be no functional change by this -- the codec
driver calls its own callback while the bus driver just calls
azx_stop() like before.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The events that are handled by HD-audio drivers are no frequent and
urgent ones, so we can use the standard workqueue without any problem
nowadays.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This makes the code flow easier -- instead of the controller driver
calling snd_hda_build_pcms() and snd_hda_build_controls() explicitly,
the codec driver itself builds PCMs and controls at probe time. Then
the controller driver only needs to call snd_card_register().
Also, this allows us the full bind/unbind control, too. Even when a
codec driver is bound later, it automatically registers the new PCM
and controls by itself.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now we have all pieces ready, and put them into places:
- add the hda_pcm refcount to azx_pcm_open() and azx_pcm_close(),
- call the most of cleanup code in hda_codec_reset() from the codec
driver remove,
- call the same code also from the hda_codec object free.
Then the codec driver can be unbound more safely now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, the hda_codec object kept the hda_pcm list in an array, and
the codec driver was expected to assign the array. However, this
makes the object life cycle management harder, because the assigned
array is freed at the codec driver detach while it might be still
accessed by the opened streams.
In this patch, we allocate each hda_pcm object dynamically and manage
it as a linked list. Each object has a kref refcount, and both the
codec driver binder and the PCM open/close touches it, so that the
object won't be freed while in use.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow the codec object to have an individual card pointer. Not only
this simplifies the redirections in many places, also this will allow
us to make each codec assigned to a different card object.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hda_build_pcms() does actually three things: let the codec driver
build up hda_pcm list, set the PCM default values, and call the
attach_pcm bus ops for each hda_pcm instance. The former two are
basically independent from the bus implementation, so it'd make the
code a bit more readable.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now the final bit of runtime PM cleanup: instead of manual
notification of the power up/down of the codec via hda_bus pm_notify
ops, use the standard runtime PM feature.
The child codec device will kick off the runtime PM of the parent
(PCI) device upon suspend/resume automatically. For managing whether
the link can be really turned off, we use the bit flags
bus->codec_powered instead of the earlier bus->power_keep_link_on.
flag. Each codec driver is responsible to set/clear the bit flag, and
the controller device can be turned off only when all these bits are
cleared.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We used to pass the power_save option value to hda_bus via a given
pointer. This was needed to refer to the value from the HD-audio core
side. However, after the transition to the runtime PM, this is no
longer needed.
This patch drops the power_save value indirection in hda_bus above,
and let the controller driver reprograms the autosuspend value
explicitly by a new helper, snd_hda_set_power_save(). Without this
call, the HD-audio core doesn't set up the autosuspend and flip the
runtime PM. (User may still be able to set up via sysfs, though.)
Along with this change, the pointer argument of azx_bus_create() is
dropped as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the previous transition of suspend/resume, now move the
power-save code to the standard runtime PM. As usual for runtime PM,
it's a bit tricky, but this simplified codes a lot in the end.
For keeping the usage compatibility, power_save module option still
controls the whole power-saving behavior on all codecs. The value is
translated to pm_runtime_*_autosuspend() and pm_runtime_allow() /
pm_runtime_forbid() calls.
snd_hda_power_up() and snd_hda_power_down() are translated to
pm_runtime_get_sync() and pm_runtime_put_autosuspend(), respectively.
Since we can do call pm_runtime_get_sync() more reliably, the sync
version is used always and snd_hda_power_up_d3wait() is dropped.
Another slight difference is that snd_hda_power_up()/down() don't call
runtime_pm code during the suspend/resume transition phase. Calling
them there isn't safe unlike our own code, resulted in unexpected
behavior (endless wakeups).
The hda_power_count tracepoint was removed, as it doesn't match well
with the new code.
Last but not least, we need to set ignore_children flag in the parent
dev.power field so that the runtime PM of the controller chip won't
get confused. The notification is still done in the bus pm_notify
callback. We'll get rid of this hack in the later patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch moves the suspend/resume mechanisms down to each codec
driver level, as we have a proper codec driver bound on the bus now.
Then we get the asynchronous PM gratis without fiddling much in the
driver level.
As a soft-landing transition, implement the common suspend/resume pm
ops for hda_codec_driver and keep the each codec driver intact. Only
the callers of suspend/resume in the controller side (azx_suspend()
and azx_resume()) are removed.
Another involved place is azx_bus_reset() calling the temporary
suspend and resume as a hackish method of bus reset. The HD-audio
core provide a helper function snd_hda_bus_reset() instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now we create the standard HD-audio bus (/sys/bus/hdaudio), and bind
the codec driver with the codec device over there. This is the first
step of the whole transition so that the changes to each codec driver
are kept as minimal as possible.
Each codec driver needs to register hda_codec_driver struct containing
the currently existing preset via the new helper macro
module_hda_codec_driver(). The old hda_codec_preset_list is replaced
with this infrastructure. The generic parsers (for HDMI and other)
are also included in the preset with the special IDs to bind
uniquely.
In HD-audio core side, the device binding code is split to
hda_bind.c. It provides the snd_hda_bus_type implementation to match
the codec driver with the given codec vendor ID. It also manages the
module auto-loading by itself like before: when the matching isn't
found, it tries to probe the corresponding codec modules, and finally
falls back to the generic drivers. (The special ID mentioned above is
set at this stage.)
The only visible change to outside is that the hdaudio sysfs entry now
appears in /sys/bus/devices, not as a sound class device.
More works to move the suspend/resume and remove ops will be
(hopefully) done in later patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no big merit to handle hda_bus_unsolicited object
individually, as it's tightly coupled with the hda_bus object itself.
Embedding it makes the code simpler in the end.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of copying from the given template, let the caller fills the
fields after creation. This simplifies the code after all.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Previously, calling one quirk function first and another later
would make the latter one take priority, this is now changed
to make the former take priority.
By adding two special values for fixup_id we can also get rid of the
fixup_forced flag.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pass the codec object so that we can replace all the rest of
snd_print*() usages with the proper device-specific print helpers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Libin Yang