BCM4320 doesn't support OID_802_11_TX_POWER_LEVEL (chip implements
the command but setting value has no effect and getting txpower value
always returns 0xff, full power). So remove the code for cleanup.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Old variant of bcm4320 doesn't handle setting configuration parameters
correctly. One symptom is that MAC gets partially overwritten when any
config parameters are set. This patch disables config-params for bcm4320a
(and generic rndis-wlan).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The temperature measurement by uCode for 5150 and 5000 are different
CSR_HW_REV_TYPE_5150: temperature sensor output voltage
CSR_HW_REV_TYPE_5000: temperature in Celsius
temperature related operation for 5150 is measured by temperature sensor
output voltage; additional conversion is required for set and store
the temperature.
To make sure support different HW design; implement _ops method for
temperature related functions (temperature reading and set ct kill
threshold)
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add "Greenfield" support for all devices except 4965 and
3945. "Greenfield" is part of 11n features to improve HT performance.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'tpt' is a delta throughput (number of packets) and is corelated
to brightness of the LED. We already maintain a delta of packets in
rxtxpackets. There is no need to calculate this delta again which
was affecting the behaviour of LEDS.
Also add two new callback functions for ASSOCIATED/DISASSOCIATED states
where LED's will be *on* for associated state and *off* for disassociated state.
This fixes
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1771.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The scratch pad register is used to store firmware status after
firmware is downloaded and initialized. After firmware status is
verified OK, the same register is used to store RX packet length.
Hence the firmware status code is no longer valid afterwards.
SD8688 firmware introduces a new register for firmware status
which will never be overwritten.
Also add scratch_reg variable to if_sdio_card structure and
initialize it based on the model of the card during probe.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This driver supports Intel's full MAC wireless multicomm 802.11 hardware.
Although the hardware is a 802.11agn device, we currently only support
802.11ag, in managed and ad-hoc mode (no AP mode for now).
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch moves some utility functions from mac80211 to cfg80211.
Because these functions are doing generic 802.11 operations so they
are not mac80211 specific. The moving allows some fullmac drivers
to be also benefit from these utility functions.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some APs seem to drift away from the expected TBTT (timestamp %
beacon_int_in_usec differs quite a bit from zero) which can result in
us waking up way too early to receive a Beacon frame. In order to work
around this, re-configure the Beacon timers after having received a
Beacon frame from the AP (i.e., when we know the offset between the
expected TBTT and the actual time the AP is sending out the Beacon
frame).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous version used a simple loop to go through all Beacon
frames when determining the next TBTT and DTIM count. This is not too
bad for the case where the setup happens before timesync (i.e., very
small TSF), but this can become very heavy operation if a short Beacon
interval is used and the current TSF is large.
In preparation for a patch to update timer setup based on Beacon
timestamp, optimize this routine to take fixed time regardless of the
actual TSF value.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SD8688 is a WLAN/Bluetooth combo chip and both functions are supported
in a single firmware image. FUNC_INIT and FUNC_SHUTDOWN commands are
implemented to utilize the multiple function feature.
When SD8688 card is inserted, the firmware image should be downloaded
only once through either WLAN function (Libertas driver) or Bluetooth
function (Bluetooth driver).
This patch adds function init/shutdown for SD8688 WLAN function only.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Usually, the 16-bit rx length is read from scratch pad registers
with two CMD52 transactions:
SD8385: IF_SDIO_SCRATCH_OLD (0x80fe/0x80ff)
SD8686/SD8688: IF_SDIO_SCRATCH (0x34/0x35)
Alternatively, SD8688 firmware offers an enhanced method for driver
to read an 8-bit rx length (in units) with a single CMD52:
IF_SDIO_RX_UNIT 0x43 is read one time after firmware is ready.
IF_SDIO_RX_LEN 0x42 is read every time when rx interrupt is received.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace direct usages of SDIO model numbers with defined macros.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The GPSI interface driver does not re-enable the Card Event Interrupt, which
causes problems after a card event (for example: link-loss) comes in. This
can lead, for example, to the card failing to re-associate. This patch
ensures that we re-enable the Card Event Interrupt when we handle card events.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is always discarded anyway but lets just set this to our
safest lowest.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_regd_init() needs to be called with the wiphy already
properly set with the bands. Without this the custom regulatory
settings were not taking effect, and the device would get
the default channel settings from ath9k_[25]ghz_chantable.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report status unknown as if there were successfully transmitted.
This will avoid hostapd to disassociate because it doesn't understand what a status unknown is.
Signed-off-by: Alexandre Becholey <alexandre.becholey@epfl.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 does not set PM field for normal data frames, so we need to
update that based on the current PS mode when using PS-Poll
(timeout=0) power save mode.
This allows the AP to remain in sync with our PS state. However, there
is still a potential race condition between PS state changes when
multiple TX queues are used and nullfunc and PS-Poll frames use
different queue. That corner case may need to be handled separately by
changing which queue is used either in ath9k or mac80211.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must make sure the chip is awake when changing the RX filter
parameters. This could have caused problems, e.g., when changing the
interface to promiscuous mode while in sleep mode.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the chip complains about TSF sync, make sure we remain awake to
sync with the next Beacon frame. In theory, this should not be needed
since we are currently trying to receive all Beacon frames, anyway,
better have this code ready should we ever change that.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the chip is in sleep mode, there is no point trying to calibrate
the radio since it will just results in incorrect values being read
from registers and other potential issues. In addition, if we actually
start processing calibrate, do not allow the chip to be put into sleep
until we have completed the calibration step.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using timeout=0 (PS-Poll) with mac80211, the driver will need to
wake up for TX requests and remain awake until the TX has been
completed (ACK received or timeout) or until the buffer frame(s) have
been received (in case the TX is for a PS-Poll frame).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we are trying to interpolate a curve with slope == 0, the return
value will always be the y-coordinate. In this code we are looping
until we reach a minimum y-coordinate on a line, which in the 0-slope
case can never happen, thus the loop never terminates.
The PCDAC steps come from the EEPROM and should never be equal, but
we should gracefully handle that case, so warn and bail out.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fix to set dev->broadcast correctly, since
dev->broadcast is defined as:
unsigned char broadcast[MAX_ADDR_LEN];
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not need to do this in ath_isr() and it looks like the modified
version ends up being more stable as far as being able receive beacon
frames is concerned. Furthermore, this reduces need to move between
AWAKE and NETWORK SLEEP states when processing some unrelated
interrupts.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently all radios receive all traffic on the simulated air
if they are tuned to the same channel. This patch introduces
the concept of grouping, which allows to assign a radio to
certain group. Only radios in the same group can 'see' each other.
Each bit in /debug/ieee80211/phy*/hwsim/group
represents one group. By default all radios belong to the same group "1",
e.g. bit 1 is set. Additionally a radio can belong to several groups.
Signed-off-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k only generated the beacon when bss_info_changed() was called,
but for AP mode this is not enough, because the TIM IE would never
get updated and consequently PS mode clients wouldn't know about
buffered frames. Instead, get a new beacon on every SWBA interrupt.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drop test for FW_STATE_RESET in p54spi_work as fw_state
is never assigned this value.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Process beacon change even if the BSSID doesn't
change at the same time. Also fix what I think
is a small locking error in b43legacy, there's
a spin_unlock_irqrestore that looks out of place.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Under high load first data word, read after available data size
is sometimes lost in p54spi_rx. It seems to depend on frequency
of interrupts and latency of data read request relatively to
'data available' interrupt. The worst consequence of this bug
is loss of packet transmission acknowledgement, which in turn
causes overflow of tx queues and permanent link loss.
Read data size and first data word in one SPI transaction.
No packets from LMAC should have length less than 1 word,
so this shouldn't interfere with the next read transaction.
Also call p54spi_sleep if p54spi_wake succeeded.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Put chip into sleep state, once it's been awaken.
Also, propagate error code to the caller.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Return whether wakeup operation succeeded.
Make use of this return value.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When SPI write of odd length is requested, p54spi_write splits it
into two parts: one for all data, except the last byte, and one
for last byte and padding byte. Unfortunately, the length of
first part is not amended. It works because all meaningful bytes
have proper value and the last byte of odd length SPI write
transaction is ignored.
p54spi_work has dummy HOST_INTERRUPTS register read at the end.
Drop it, as its result is not used and it has no side effects.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Host is not allowed to modify DMA_WRITE_CTRL register
if bit HOST_ALLOWED in it is not set. Wait for HOST_ALLOWED first.
Also get rid of timeout in p54spi_wait_bit as it's been playing
a role of workaround for such an incorrect register access.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliminate direct accesses to the driver_data field.
cf 82ab13b26f15f49be45f15ccc96bfa0b81dfd015
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct device *dev;
expression E;
type T;
@@
- dev->driver_data = (T)E
+ dev_set_drvdata(dev, E)
@@
struct device *dev;
type T;
@@
- (T)dev->driver_data
+ dev_get_drvdata(dev)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is one of the incremental steps for unifying iwl_station_entry
for all HWs, i.e. removing of iwl3945_station_entry
This patch drops iwl3945_tid_data and use iwl_tid_data instead.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces struct iwl3945_hw_key by struct iwl_hw_key.
It's not used directly with any host command therefore removal is trivial
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes unnecessary MMIO accesses in the interrupt hotpath. The
patch by Michael Buesch for b43 has been ported to b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch configures the beacon timers with beacon interval
and beacon period passed through vif.bss_conf. Also cache the
currecnt beacon configuration which will be used to configure
the beacon timers when the driver triggers it after reset.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous implementation was moving back to NETWORK SLEEP state
immediately after receiving a Beacon frame. This means that we are
unlikely to receive all the buffered broadcast/multicast frames that
would be sent after DTIM Beacon frames. Fix this by parsing the Beacon
frame and remaining awake, if needed, to receive the buffered
broadcast/multicast frames. The last buffered frame will trigger the
move back into NETWORK SLEEP state.
If the last broadcast/multicast frame is not received properly (or if
the AP fails to send it), the next Beacon frame will work as a backup
trigger for returning into NETWORK SLEEP.
A new debug type, PS (debug=0x800 module parameter), is added to make
it easier to debug potential power save issues in the
future. Currently, this is only used for the Beacon frame and buffered
broadcast/multicast receiving.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes use of the local fc variable in bit more places and uses a
common helper macro. The part of RX process that delivers skb's to
mac80211 is moved to a separate function in preparation for future
changes that will need to do this from two places. The modifications
here should not result in any functional changes.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The broadcast bit is in the first, not the last octet..
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to my tests, all that ZD_CS_MULTICAST does is to
disable retrying/waiting for an ACK. Reflect this by renaming
the bit to ZD_CS_NO_ACK and setting it based on
IEEE80211_TX_CTL_NO_ACK, instead of is_multicast_ether_addr.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is more consistent with our nl80211 naming convention
for HT40-/+.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are not correctly listening to the regulatory max bandwidth
settings. To actually make use of it we need to redesign things
a bit. This patch does the work for that. We do this to so we
can obey to regulatory rules accordingly for use of HT40.
We end up dealing with HT40 by having two passes for each channel.
The first check will see if a 20 MHz channel fits into the channel's
center freq on a given frequency range. We check for a 20 MHz
banwidth channel as that is the maximum an individual channel
will use, at least for now. The first pass will go ahead and
check if the regulatory rule for that given center of frequency
allows 40 MHz bandwidths and we use this to determine whether
or not the channel supports HT40 or not. So to support HT40 you'll
need at a regulatory rule that allows you to use 40 MHz channels
but you're channel must also be enabled and support 20 MHz by itself.
The second pass is done after we do the regulatory checks over
an device's supported channel list. On each channel we'll check
if the control channel and the extension both:
o exist
o are enabled
o regulatory allows 40 MHz bandwidth on its frequency range
This work allows allows us to idependently check for HT40- and
HT40+.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not go beyond ARRAY_SIZE of intf->crypto_stats
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
enable iwl driver to support 5000 ucode having version 2 of API
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"airo: airo_get_encode{,ext} potential buffer overflow" was actually a
no-op, due to an unrecognized type overflow in an assignment. Oddly,
gcc only seems to tell me about it when using -Wextra...grrr...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the EEPROM contains weird values for the power levels we have to
fix the interpolation process.
Signed-off-by: Fabio Rossi <rossi.f@inwind.it>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calling cancel_delayed_work() from inside
spin_lock_irqsave, introduces a potential deadlock.
As explained by Johannes Berg <johannes@sipsolutions.net>
A - lock
T - timer
phase CPU 1 CPU 2
---------------------------------------------
some place that calls
cancel_timer_sync()
(which is the | code)
lock-irq(A)
| "lock-irq"(T)
| "unlock"(T)
| wait(T)
unlock(A)
timer softirq
"lock"(T)
run(T)
"unlock"(T)
irq handler
lock(A)
unlock(A)
Now all that again, interleaved, leading to deadlock:
lock-irq(A)
"lock"(T)
run(T)
IRQ during or maybe
before run(T) --> lock(A)
"lock-irq"(T)
wait(T)
We fix this by moving the call to cancel_delayed_work() into workqueue.
There are cases where the work may not actually be queued or running
at the time we are trying to cancel it, but cancel_delayed_work() is
able to deal with this.
Also cleanup iwl_set_mode related to this call. This function
(iwl_set_mode) is only called when bringing interface up and there will
thus not be any scanning done. No need to try to cancel scanning.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13224, which was also
reported at http://marc.info/?l=linux-wireless&m=124081921903223&w=2 .
Tested-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit e8f055f0c3 ("ath5k: Update reset code") subtly changed the
code that computes floating point values for the PHY3_TIMING register
such that the exponent is off by a decimal point, which can cause
problems with OFDM channel operation.
get_bitmask_order() actually returns the highest bit set plus one,
whereas the previous code wanted the highest bit set. Instead, use
ilog2 which is what this code is really calculating. Also check
coef_scaled to handle the (invalid) case where we need log2(0).
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR5K_PHY_PLL_40MHZ_5413 should not be ORed with AR5K_PHY_MODE_RAD_RF5112
for 5 GHz channels.
The incorrect PLL value breaks scanning in the countries where 5 GHz
channels are allowed.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch fixes issues with dev->dev_addr changing from array to pointer.
Hopefully there are no others.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6:
iwlwifi: fix device id registration for 6000 series 2x2 devices
ath5k: update channel in sw state after stopping RX and TX
rtl8187: use DMA-aware buffers with usb_control_msg
mac80211: avoid NULL ptr deref when finding max_rates in PID and minstrel
airo: airo_get_encode{,ext} potential buffer overflow
Pulled directly by Linus because Davem is off playing shuffle-board at
some Alaskan cruise, and the NULL ptr deref issue hits people and should
get merged sooner rather than later.
David - make us proud on the shuffle-board tournament!
This patch makes the return type of some of the functions
void as those functions always return true
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Show current qos AC parameters in sysfs
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add "rate_scale_data" debugfs file to show current bit rate (HT and Legacy),
plus additional information (rssi, noise, tsf, beacon time stamp).
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hard coded value, use the define in iwl-commands.h for
better code maintenance
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Read rev id in nic_config instead of nic_init.
Nic_config has some checking for rev_id but we actually don't read
the rev_id in there.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Somehow these pre-production cards are showing up in the community.
With this message we hope that it will be clear that the hardware is not
supported.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlagn rate scaling will periodically search other rate scale
tables to switch to the best table regarding performance. In the past
the number of search tables were 3. Every time the rate scale algorithm
goes through these available tables in will stay in current table for
some time before start searching again. Recent driver support more
feature and antenna, so we have more tables to search. This patch make
sure we go through all available tables.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes all the dead code that tries to adjust the power
saving level based on the system AC state (inacceptable policy
in the kernel) or based on overtemp conditions (unused).
Also, pass _all_ policy wrt. enabling PS to mac80211, since
we do not use the power_disabled internally I now use that to
mirror the mac80211 CONF_PS setting. When mac80211 turns off
CONF_PS we follow suit. This means that the user power level
(which can currently only be set from sysfs) is not touched
for mac80211 powersave changes.
This means no "association status" checks are necessary since
mac80211 will not allow power save to be enabled when not
associated.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi internally needs to keep track of whether PS
is enabled in the firmware or not. To do this, it keeps
a bit in the status flags, called STATUS_POWER_PMI.
The code to set this bit looks as follows:
static int iwl_set_power(struct iwl_priv *priv, void *cmd)
{
return iwl_send_cmd_pdu_async(priv, POWER_TABLE_CMD,
sizeof(struct iwl_powertable_cmd),
cmd, NULL);
}
int iwl_power_update_mode(...)
{
[...]
if (final_mode != IWL_POWER_MODE_CAM)
set_bit(STATUS_POWER_PMI, &priv->status);
iwl_update_power_cmd(priv, &cmd, final_mode);
cmd.keep_alive_beacons = 0;
if (final_mode == IWL_POWER_INDEX_5)
cmd.flags |= IWL_POWER_FAST_PD;
ret = iwl_set_power(priv, &cmd);
if (final_mode == IWL_POWER_MODE_CAM)
clear_bit(STATUS_POWER_PMI, &priv->status);
else
set_bit(STATUS_POWER_PMI, &priv->status);
if (priv->cfg->ops->lib->update_chain_flags && update_chains)
priv->cfg->ops->lib->update_chain_flags(priv);
[...]
}
Now, this bit really needs to track what the _firmware_
thinks, not what the driver thinks. Therefore, there is
a race condition here -- the driver sets the bit before
it knows that the async command sent to the card in the
iwl_set_power function has been processed. As a result,
the call to update_chain_flags() may think that the card
has been woken up (PMI bit cleared) while in reality it
hasn't processed the async POWER_TABLE_CMD yet.
This leads to bugs -- any commands the update_chain_flags
function sends can get stuck and subsequent commands also
fail.
The fix is almost trivial: since there's no reason to send
an async command here (in fact, there almost never should
be since many mac80211 callbacks can sleep) just make the
function wait for the card to process the command and then
return and clear the PMI bit.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the microcode fails for any reason, ask mac80211 to
recover instead of trying ourselves and failing at it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There really is no need to have a separate struct for a
single variable. The fact that it exists is due to the
code legacy, but we can remove that now. Very simple.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The lower 4 bytes of the chipset revision must contain
a non-zero value. This bug was introduced by
"rt2x00: Simplify rt2x00_check_rev".
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's not needed outside iwl-core.c
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
m68k allmodconfig:
| drivers/net/wireless/wl12xx/main.c: In function 'wl12xx_probe':
| drivers/net/wireless/wl12xx/main.c:1273: error: implicit declaration of function 'set_irq_type'
| make[1]: *** [drivers/net/wireless/wl12xx/main.o] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add device ids for 2x2 devices. Also fix antenna usage because these devices use
antennas A and B, not B and C.
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Feeding the return code of get_wep_key directly to the length parameter
of memcpy is a bad idea since it could be -1...
Reported-by: Eugene Teo <eugeneteo@kernel.sg>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
bonding: fix panic if initialization fails
IXP4xx: complete Ethernet netdev setup before calling register_netdev().
IXP4xx: use "ENODEV" instead of "ENOSYS" in module initialization.
ipvs: Fix IPv4 FWMARK virtual services
ipv4: Make INET_LRO a bool instead of tristate.
net: remove stale reference to fastroute from Kconfig help text
net: update skb_recycle_check() for hardware timestamping changes
bnx2: Fix panic in bnx2_poll_work().
net-sched: fix bfifo default limit
igb: resolve panic on shutdown when SR-IOV is enabled
wimax: oops: wimax_dev_add() is the only one that can initialize the state
wimax: fix oops if netlink fails to add attribute
Bluetooth: Move dev_set_name() to a context that can sleep
netfilter: ctnetlink: fix wrong message type in user updates
netfilter: xt_cluster: fix use of cluster match with 32 nodes
netfilter: ip6t_ipv6header: fix match on packets ending with NEXTHDR_NONE
netfilter: add missing linux/types.h include to xt_LED.h
mac80211: pid, fix memory corruption
mac80211: minstrel, fix memory corruption
cfg80211: fix comment on regulatory hint processing
...
The AR_SREV_9285_1[12]_OR_LATER macros already contains the
AR_SREV_9285 check.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On x86 this allows us to do the following small savings:
shave off 23 % off of the module's data, and
shave off 6 % off of the module's text.
We save 456 bytes, for those counting.
$ size ath9k.ko
text data bss dec hex filename
250794 3628 1600 256022 3e816 ath9k.ko
$ size ath9k-old.ko
text data bss dec hex filename
239114 15308 1600 256022 3e816 ath9k-old.ko
$ du -b ath9k.ko
4034244 ath9k.ko
$ du -b ath9k-old.ko
4033788 ath9k-old.ko
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently queues are stopped when their length reaches their length limit,
but are restarted only when the size of freed range of packet buffer is
not less than the size of the largest possible packet.
This causes permanent queue stop on radio visibility loss in the middle
of ping series: there is plenty of room in the packet buffer, but it is
never freed more than 3 (size of 'best effort' queue) * 288 (ping packet
plus headers) bytes at once.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00_check_rev() was too specific for rt2500usb and rt73usb,
by adding the mask argument (instead of hardcoding it into
the function itself) we can use the function in rt2800usb as
well.
v2: Fix revision mask for rt2800usb
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix this build error when CONFIG_PM is not set:
drivers/net/wireless/ath/ar9170/usb.c: In function 'ar9170_usb_probe':
drivers/net/wireless/ath/ar9170/usb.c:692:
error: 'struct usb_device' has no member named 'reset_resume'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
/drivers/net/wireless/p54/p54usb.c: In function 'p54u_probe':
/drivers/net/wireless/p54/p54usb.c:923: error: 'struct usb_device' has no member named 'reset_resume'
In the struct usb_device the reset_resume attribute is only available
when CONFIG_PM is defined.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes warnings:
drivers/net/wireless/wl12xx/main.c:87: warning: int format, different
type arg (arg 2)
drivers/net/wireless/wl12xx/main.c: In function `wl12xx_fetch_nvs':
drivers/net/wireless/wl12xx/main.c:125: warning: int format, different
type arg (arg 2)
drivers/net/wireless/wl12xx/wl1251.c: In function 'wl1251_upload_firmware':
drivers/net/wireless/wl12xx/wl1251.c:94: warning: int format, different
type arg (arg 2)
drivers/net/wireless/wl12xx/wl1251.c:141: warning: int format, different
type arg (arg 2)
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces test_and_set_bit by set_bit since the bit is not
tested anyway
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch change the "is_fat" checking in rate scale to use
iwl_is_fat_tx_allowed() to match the sta and RX_ON command setting.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Conrad Kostecki <ConiKost@gmx.de>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some issues in PS prevent us from supporting it reliably.
When 4965 goes to sleep it stores some data in host DRAM, reads it back
when device wakes up. In 4965 there is a problem that the data is not
correct when ucode starts using it upon wakeup.
For all iwlagn devices there is a problem where command is sent when PS is
enabled. At the moment there is a locking problem with priv->lock not being
held and thus not requesting nic access correctly.
We disable PS until these issues have been resolved.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch seperates rx_used and rx_free into two
different atomic contexts. We can now avoid using GFP_ATOMIC
for skb allocation and use GFP_KERNEL.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add LED support on the IBM ThinkPad 11a/b/g Wireless LAN Mini Express
Adapter (AR5BXB6), found on the IBM/Lenovo Thinkpad X60/T60/Z60 series.
Signed-off-by: Paride Legovini <legovini@spiro.fisica.unipd.it>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update ath5k to use the ctl settings for tx power based on current
regulatory domain.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add spur filter support for RF5413 and later chips
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add code to support the various antenna scenarios supported by hw
* For now hardcode the default scenario (single or dual omnis with
tx/rx diversity working and tx antenna handled by session -hw keeps
track on which antenna it got ack from each ap/station and maps each
ap/station to one of the antennas-).
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After some debuging we were hitting the following bugs so far...
* Due to huge channel list hostapd couldn't get infos from the driver
and couldn't set the channel. If we manualy set the channel after
hostapd starts (by setting channel to 0 -auto), beacons are sent
but they wont show up on scan because they are malformed (they have
channel = 0 because hostapd doesn't update the channel info -this is
probably a hostapd bug so i'm CCing Jouni) and they get dropped. Bob
fixed this by only allowing standard channels to be registered so
now hostapd works as expected.
* Docs (and HAL source) say that we must write 0 on timer0 when
operating on AP mode to start TSF increment but this seems to
mess with DBA in many cases and beacon queue never gets started.
We fixed that on the previous patch.
We have some more things to deal with...
* For some reason (hw bug or something else) after restarting hostapd
a few times, beacon inteval seems to change from 100ms to a sec
(we get one beacon per sec).
* We need to set sleep timers on STA mode and enable power saving +
support PCF.
...but i think it's time we enable AP support "officialy" so that
we can get more feedback from users. I ran ath5k with the mentioned
patches + hostapd 0.6.8 and AP mode worked fine (it had some less
throughput on my tests than IBSS but it worked).
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Write next beacon timer even on AP mode since without this we get
no beacons + ath9k does it too. Docs say that we must write 0 on
this register on AP mode to start TSF increment, we do both to be
on the safe side.
* Fix num_tx_pending function, we never read the register :P that's
why we got all those "beacon queue 7 didn't stop messages".
* Put full prioriy on beacon queue, lock all queues with lower
priority using the arblock and also bypass any arblock by seting
the arblock ignore flag.
* For the CAB queue (do we need this thing ?, it seems crap) since
it's supposed to fire up after each beacon (we don't use it on driver
part, ath9k/MadWiFi does), don't make it DBA gated but instead make
it fire after each beacon by using the beacon sent gated flag.
* Increase bmiss threshold to 10, that's what we used on MadWiFi for
a long time. Also when we have pending frames on the beacon queue (we
got a beacon that didn't make it on the air) it's more likely that
the beacon queue never started, probably due to faulty DBA setting,
so change that "beacon queue didn't stop" message.
Tested this with AP mode and IBSS mode and seems to work fine ;-)
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Put remaining EEPROM information on ee struct and remove is_hb63
function.
Now we also have rfkill stuff available.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Read Spur channel information from EEPROM and use default channels
for RF5413 compatible chips that don't have this info on EEPROM.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Now that we have regulatory control enable the driver to set
txpower on hw
* Also use txpower table offset so that we can match
power range set by user/driver with indices on power table.
Tested 2 different cards (a CM9 and an RF5112-based ubnt) and got
the same output using a remote machine to measure per-packet rssi
(conected the cards using attenuators). I also switched between
various tx power levels and i saw an equal power change on the remote
machine (so txpower changes as expected) and verified that we have
the same output on each rate.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ralink released a new rt2870 driver, these are the obvious
differences I could find. It doesn't same to make my device
work better, but neither does it seem to regress...
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl12xx is a driver for TI wl1251 802.11 chipset designed for embedded
devices, supporting both SDIO and SPI busses. Currently the driver
supports only SPI. Adding support 1253 (the 5 GHz version) should be
relatively easy. More information here:
http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?contentId=4711&navigationId=12494&templateId=6123
(Collapsed original sequence of pre-merge patches into single commit for
initial merge. -- JWL)
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for the rt2800usb chipset.
Current problems:
* Cannot scan 11n AP's
* No TX during first minute after association
* Broken Hardware encryption
Includes various patches from Mattias, Felix, Xose and Axel.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Axel Kollhofer <rain_maker@root-forum.org>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extra parenthesis are not needed in these 2 cases,
all other defines in rt2x00 are done without parenthesis
so just fixup these 2 cases.
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The spin_lock handling uses lots of instructions on some archs.
With this patch the size of the ath9k module will be significantly
smaller.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we aren't doing anything in mac80211, we can turn off
much of the hardware, depending on the driver/hw. Not doing
anything, aka being idle, means:
* no monitor interfaces
* no AP/mesh/wds interfaces
* any station interfaces are in DISABLED state
* any IBSS interfaces aren't trying to be in a network
* we aren't trying to scan
By creating a new function that verifies these conditions and calling
it at strategic points where the states of those conditions change,
we can easily make mac80211 tell the driver when we are idle to save
power.
Additionally, this fixes a small quirk where a recalculated powersave
state is passed to the driver even if the hardware is about to stopped
completely.
This patch intentionally doesn't touch radio_enabled because that is
currently implemented to be a soft rfkill which is inappropriate here
when we need to be able to wake up with low latency.
One thing I'm not entirely sure about is this:
phy0: device no longer idle - in use
wlan0: direct probe to AP 00:11:24:91:07:4d try 1
wlan0 direct probe responded
wlan0: authenticate with AP 00:11:24:91:07:4d
wlan0: authenticated
> phy0: device now idle
> phy0: device no longer idle - in use
wlan0: associate with AP 00:11:24:91:07:4d
wlan0: RX AssocResp from 00:11:24:91:07:4d (capab=0x401 status=0 aid=1)
wlan0: associated
Is it appropriate to go into idle state for a short time when we have
just authenticated, but not associated yet? This happens only with the
userspace SME, because we cannot really know how long it will wait
before asking us to associate. Would going idle after a short timeout
be more appropriate? We may need to revisit this, depending on what
happens.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check for IEEE80211_TX_CTL_NO_ACK instead of is_multicast_ether_addr
when determining whether to use lowest rate without retries.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make iwl-{3945|agn}-rs check for IEEE80211_TX_CTL_NO_ACK instead of
is_multicast_ether_addr when determining whether to use the lowest
rate, and set the retry count to 0 (total try count = 1) if
IEEE80211_TX_CTL_NO_ACK is set.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Greear points out that the "too many interrupts" message will
never print in the intended case since the interrupt counter
will be -1 after the loop. Change it to pre-decrement so it will
be 0 on the thousandth iteration.
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend rt2x00lib capabilities to support 802.11n,
it still lacks aggregation support, but that can
be added in the future.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware require L2 padding between header and payload
because both must be aligned to a 4-byte boundary. This hardware
also is easier during the RX path since we no longer need to
move the entire payload but rather only the header to remove
the padding (mac80211 only wants the payload to be 4-byte aligned).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By placing the iv_len into the tx descriptor data and
by passing this data to the crypto IV handlers we can
save multiple calls to ieee80211_get_hdrlen_from_skb()
and some if-statements when copying/removing the IV data
from the outgoing frame.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 8e218fb24f reverted the previous
patch (commit 925be8a307).
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
remove redundant test: outlen is unsigned
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch takes care of an outstanding comment in
"[PATCH] ar9170usb: fix hang on resume" commit message.
>However, the device does not accept the firmware on resume.
>and it will exit with:
>
>> firmware part 1 upload failed (-71).
>> device is in a bad state. please reconnect it!
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch redo the driver code so that p54usb no longer hangs
the kernel on resume.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since "p54: prevent upload of wrong firmwares" we no longer allow
outdated LM86 firmwares to be uploaded on ISL3887 (LM87) devices.
Therefore we can purge this buggy legacy code altogether.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set null key type even on ar5211, otherwise it en/decrypts every frame with
protected bit set which renders the card unusable on encrypted networks.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uncomment a few lines that survived the RFCs.
However, there is not much to worry about, since AP mode is
not officially advertised and supported.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otus uses slightly different set of "Minimum MPDU Start Spacing" values
than the 802.11n D2.0 specifies. (the whole table is shifted by one and
therefore the 16us spacing is not officially available!)
And while we're at it, we also initialize our MAC's density register.
So, this annoying _feature_ will not break TX A-MPDU later.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A typo slipped into my patch to configure beacon intervals
properly -- this warning is supposed to trigger when the
beacon interval is zero, not non-zero.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The config_interface method is a little strange, it contains the
BSSID and beacon updates, while bss_info_changed contains most
other BSS information for each interface. This patch removes
config_interface and rolls all the information it previously
passed to drivers into bss_info_changed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently have two beacon interval configuration knobs:
hw.conf.beacon_int and vif.bss_info.beacon_int. This is
rather confusing, even though the former is used when we
beacon ourselves and the latter when we are associated to
an AP.
This just deprecates the hw.conf.beacon_int setting in favour
of always using vif.bss_info.beacon_int. Since it touches all
the beaconing IBSS code anyway, we can also add support for
the cfg80211 IBSS beacon interval configuration easily.
NOTE: The hw.conf.beacon_int setting is retained for now due
to drivers still using it -- I couldn't untangle all
drivers, some are updated in this patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
e1000: fix virtualization bug
bonding: fix alb mode locking regression
Bluetooth: Fix issue with sysfs handling for connections
usbnet: CDC EEM support (v5)
tcp: Fix tcp_prequeue() to get correct rto_min value
ehea: fix invalid pointer access
ne2k-pci: Do not register device until initialized.
Subject: [PATCH] br2684: restore net_dev initialization
net: Only store high 16 bits of kernel generated filter priorities
virtio_net: Fix function name typo
virtio_net: Cleanup command queue scatterlist usage
bonding: correct the cleanup in bond_create()
virtio: add missing include to virtio_net.h
smsc95xx: add support for LAN9512 and LAN9514
smsc95xx: configure LED outputs
netconsole: take care of NETDEV_UNREGISTER event
xt_socket: checks for the state of nf_conntrack
bonding: bond_slave_info_query() fix
cxgb3: fixing gcc 4.4 compiler warning: suggest parentheses around operand of ‘!’
netfilter: use likely() in xt_info_rdlock_bh()
...
We need to be symmetrical in what is done when key is set and cleared.
This is important wrt the key flags as they are used during key
clearing and if they are not set when the key is set the key cannot be
cleared completely.
This addresses the many occurences of the WARN found in
iwl_set_tkip_dynamic_key_info() and tracked in
http://www.kerneloops.org/searchweek.php?search=iwl_set_dynamic_key
If calling iwl_set_tkip_dynamic_key_info()/iwl_remove_dynamic_key()
pair a few times in a row will cause that we run out of key space.
This is because the index stored in the key flags is used by
iwl_remove_dynamic_key() to decide if it should remove the key.
Unfortunately the key flags, and hence the key index is currently only
set at the time the key is written to the device (in
iwl_update_tkip_key()) and _not_ in iwl_set_tkip_dynamic_key_info().
Fix this by setting flags in iwl_set_tkip_dynamic_key_info().
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It does not make sense to apply EXPORT_SYMBOL to a static symbol. Fixes
this build error:
drivers/net/wireless/iwlwifi/iwl3945-base.c:1697: error: __ksymtab_iwl3945_rx_queue_reset causes a section type conflict
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
char bname[5] is too small for the string "X GHz" when the null
terminator is taken into account. Thus, turning on rate debugging
can crash unless we have lucky stack alignment.
Cc: stable@kernel.org
Reported-by: Paride Legovini <legovini@spiro.fisica.unipd.it>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Under certain circumstances iwlwifi can get stuck and will no
longer accept scan requests, because the core code (cfg80211)
thinks that it's still processing one. This fixes one of the
points where it can happen, but I've still seen it (although
only with my radio-off-when-idle patch).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_wext_link_change() might be called from rndis_command() at
initialization stage and priv->workqueue/priv->work have not been
initialized yet. This causes invalid opcode at rndis_wext_bind on
some brands of bcm4320.
Fix by initializing workqueue/workers in rndis_wext_bind() before
rndis_command is used.
This bug has existed since 2.6.25, reported at:
http://bugzilla.kernel.org/show_bug.cgi?id=12794
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/iwlwifi/iwl3945-base.c:1415: error: __ksymtab_iwl3945_rx_queue_reset causes a section type conflict
I am pretty sure that this is a compiler bug, so not to worry. However,
as far as I can see, iwl-3945.o (the only user) and iwl3945-base.o are
always linked into the same module, so the EXPORT_SYMBOL (which causes
the problem) should not be needed. Correct?
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
net/mac80211/tx.c: In function ‘ieee80211_tx_h_select_key’:
net/mac80211/tx.c:448: warning: ‘key’ may be used uninitialized in this function
drivers/net/wireless/ath/ath9k/rc.c: In function ‘ath_rc_rate_getidx’:
drivers/net/wireless/ath/ath9k/rc.c:815: warning: ‘nextindex’ may be used uninitialized in this function
drivers/net/wireless/hostap/hostap_plx.c: In function ‘prism2_plx_probe’:
drivers/net/wireless/hostap/hostap_plx.c:438: warning: ‘cor_index’ may be used uninitialized in this function
drivers/net/wireless/hostap/hostap_plx.c:438: warning: ‘cor_offset’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/libertas/if_spi.c: In function ‘if_spi_c2h_data’:
drivers/net/wireless/libertas/if_spi.c:733: warning: format ‘%u’ expects type ‘unsigned int’, but argument 4 has type ‘long unsigned int’
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (94 commits)
netfilter: ctnetlink: fix gcc warning during compilation
net/netrom: Fix socket locking
netlabel: Always remove the correct address selector
ucc_geth.c: Fix upsmr setting in RMII mode
8139too: fix HW initial flow
af_iucv: Fix race when queuing incoming iucv messages
af_iucv: Test additional sk states in iucv_sock_shutdown
af_iucv: Reject incoming msgs if RECV_SHUTDOWN is set
af_iucv: fix oops in iucv_sock_recvmsg() for MSG_PEEK flag
af_iucv: consider state IUCV_CLOSING when closing a socket
iwlwifi: DMA fixes
iwlwifi: add debugging for TX path
mwl8: fix build warning.
mac80211: fix alignment calculation bug
mac80211: do not print WARN if config interface
iwl3945: use cancel_delayed_work_sync to cancel rfkill_poll
iwlwifi: fix EEPROM validation mask to include OTP only devices
atmel: fix netdev ops conversion
pcnet_cs: add cis(firmware) of the Allied Telesis LA-PCM
mlx4_en: Fix cleanup if workqueue create in mlx4_en_add() fails
...
Private structure is allocated by wiphy_new now, so use
wiphy_free instead of kfree.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_wext_link_change() might be called from rndis_command() at
initialization stage and priv->workqueue/priv->work have not been
initialized yet. This causes invalid opcode at rndis_wext_bind on
some brands of bcm4320.
Fix by initializing workqueue/workers in rndis_wext_bind() before
rndis_command is used.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sparse complains, correctly, about these:
drivers/net/wireless/rndis_wlan.c:418:21: warning: symbol 'rndis_config_ops' was not declared. Should it be static?
drivers/net/wireless/rndis_wlan.c:423:6: warning: symbol 'rndis_wiphy_privid' was not declared. Should it be static?
Fix that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow user to config the device all the time but only allow commiting
these changes to card if the card is up and running.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch removes the "manual radio disable" parameter
as there is no usage scenario of disabling radio using this module parameter.
User can use iwconfig's txpower to enable and disable radio.
This module parameter also does not work as expected. During module load
the status of radio is set, the radio is not actually disabled. Even so,
the moment mac80211 requests the interface to be up the radio will be
enabled again.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Function rs_stay_in_table was flushing the rate scale table way to early. time_after
macro in expecting long value and was failing because we passing u32 value.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch clean up the code for NL80211_IFTYPE_MONITOR mode,
priv->iw_mode is set in add_interface, but add_interface is never called
for monitor mode.
The only way mac80211 informs us about monitor mode is through
configuring filter; since iw_mode will never set to
NL80211_IFTYPE_MONITOR, modify and remove all the code refer to
NL80211_IFTYPE_MONITOR and replace with iwl_is_monitor_mode() function
call.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch calculates interrupt statistics for debugfs.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch adds debugfs to 3945. Also fix debugfs registration in iwlagn
to return error code if it fails.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If passive scanning is requested we should not ask the
microcode to do active scanning after detecting traffic
on a channel -- that should only be used when an active
scan is requested but some channels are marked passive.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This modifies iwlwifi to
* no longer build its own probe request, but use mac80211's
* therefore, support arbitrary scan IEs (up to the max len)
* support multiple scan SSIDs
* support passive scanning
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This limit applies to current (APIv1 and APIv2) 3945 firmware only, not
supported firmware of any of the other cards.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this patch ar9170 is capable of receiving aggregated 802.11n frames
and sniffing on most networks without having a "debug message overhead".
(Includes phy initialization requested by
Johannes Berg <johannes@sipsolutions.net> -- JWL)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for configuring HT40 channels
and receiving HT40 to ar9170. Receiving aggregation
doesn't seem to work right now, so it's not enabled.
Same goes for TX aggregation, but that probably needs
even more work.
With this, I can receive roughly 33 Mbits/sec.
The HT capabilities are a little odd, I tried following
otus here -- in particular having SGI_40 but not SGI_20
is a little weird but afaict that's what otus does.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Supporting wireless extension nickname is pointless
and no other modern driver supports this, so remove
it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trying to separate header files into net/wireless.h and
net/cfg80211.h has been a source of confusion. Remove
net/wireless.h (because there also is the linux/wireless.h)
and subsume everything into net/cfg80211.h -- except the
definitions for regulatory structures which get moved to
a new header net/regulatory.h.
The "new" net/cfg80211.h is now divided into sections.
There are no real changes in this patch but code shuffling
and some very minor documentation fixes.
I have also, to make things reflect reality, put in a
copyright line for Luis to net/regulatory.h since that
is probably exclusively written by him but was formerly
in a file that only had my copyright line.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PS-Polled frames must be sent with OUT_NOCANCEL flag set,
or the firmware will reject all of them, at the station is still blacklisted.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following patch implements some control over the LED on RTL8187B and
RTL8187L devices. Triggers are registered for TX and RX. Whenever the
trigger event occurs, the LED is turned off for 1/20 second, then turned
back on.
Note: For those RTL8187X devices that are built into the computer and have
a LED that is expected to be controlled with a radio switch, this patch will
not operate that LED. That will take a separate patch to be prepared later.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A detection function was added for identifying CF8381.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch deactivates powersave in station mode.
It does not work correctly yet, so the code does more harm than good.
(I split the original patch and sent part of it for 2.6.30, which didn't
have the IEEE80211_HW_BEACON_FILTER flag. -- JWL)
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the EEPROM is not in good condition we cannot continue so
we currently bail out but only ath5k is bailing out properly.
Both ath9k and ar9170 were proceeding and if a user were to run
into this they'd see an obscure panic. Lets propagate the error
as intended and make sure we inform the user by lifting the
error message from debug to a kernel error.
Stable note: You can find a port of this page here:
http://bombadil.infradead.org/~mcgrof/patches/ath9k/ath9k-fix-eeprom.patch.txt
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Grabbing an ath5k_buf then dropping the lock is racy because the
referenced descriptor can be obtained in another thread and released
before the buffer is handed to the hardware. Likewise, manipulating
sc->rxlink without the lock can lead to having multiple self-linked
hardware descriptors.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies the code used to detect when the
self-linked DMA buffer is still in use by hardware, by
checking the hardware's rxdp register instead of looking
at the software buffer list.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current code uses int types, but both modparams are boolean values.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For embedded platforms, beacon transmission can be starved when
flooded with data packets. Prioritize beacons by giving the beacon
queue the first shot when the isr completes.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch corrects a few errors in the initvals tables to match those
in the HAL tables. Namely, remove a couple of repetitions, fix some
turbo mode errors, and correct a register for the CCK rate power table.
Changes-licensed-under: ISC
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christoph Hellwig pointed out that these stubs are unnecessary.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds licensing, author information and a description to the module.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This message appears to be nothing more than a leftover of the
experimental-8187B era. Also, we print the HW type in the hwaddr line,
making this message reduntant. And it's definitely not important
enough to be a KERN_WARNING.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is already handled properly in ath9k_hw_getnf.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in ath9k_hw_init_cal() where the wrong
calibration was being done for non-AR9285 chipsets.
Also add a few helpful comments.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces old 'hal_' prefixes with 'ath9k_'.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up the functions dealing with calibration,
using proper return values.
ath9k_hw_per_calibration(), ath9k_hw_calibrate now return bool values
instead of setting error values in the function arguments.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The various ANI timers have to be initialized properly when
starting the calibration timer.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ADC gain calibration has to be done for all non 2GHZ-HT20 channels.
Regression from "ath9k: use ieee80211_conf on ath9k_hw_iscal_supported()"
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The operating HT mode is stored in chanmode and
not channelFlags.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A full HW reset needs to be done on termination of a scan run.
Not setting SC_OP_FULL_RESET resulted in doing a
fast channel change.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver-specific region has to be freed in case
of a DMA mapping failure.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Radio enable/disable have to handle ASPM state properly.
This patch fixes it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_getisr() doesn't appear to set anything in the status mask for
PCI FATAL or PERR interrupts (AR_INTR_SYNC_HOST1_FATAL/PERR), which
the open-source HAL seems to do. This means that the card isn't reset
after these interrupts.
This patch seems to fix a problem where the wireless drops out with an
"ath9k: received PCI FATAL interrupt" in dmesg after some time; the
hardware is an AR5416 in an ASUS WL-500W running 2.6.28.7 (OpenWRT) and
compat-wireless 2009-03-31.
Signed-off-by: Steven Luo <steven@steven676.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ports commit c97a4ccc1f "b43: Fix beacon BH update" to
b43legacy. It fixes beacon updating in the bottomhalf. In case the device
is busy, we will defer to later in the IRQ handler.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Tested-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ports the beaconing fixes from commit a82d992261 "b43: Beaconing
fixes" to b43legacy. Basically it prevents the card from triggering the beacon
IRQ over and over again.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Tested-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The signal quality percentage is now calculated by mac80211 stack.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch takes care of outstanding TODOs:
/* TODO: some devices have 4 more free slots for rx keys */
Now the driver can utilize all available key slots instead of just 4.
Obviously, this helps most in AP/IBSS(/MESH) mode, when
we have to use more different keys.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes unnecessary MMIO accesses in the interrupt hotpath.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/libertas/rx.c: In function ‘lbs_process_rxed_packet’:
drivers/net/wireless/libertas/rx.c:184: warning: format ‘%zd’ expects type ‘signed size_t’, but argument 4 has type ‘__le32’
drivers/net/wireless/libertas/rx.c:184: warning: format ‘%zd’ expects type ‘signed size_t’, but argument 5 has type ‘unsigned int’
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds interrupt statistics report to debugfs, this can help to
understand number of interrupts happened which including HW/SW error for
easier and better debugging.
in /sys/kernel/debug/ieee80211/phyN/iwlagn/data directory
use "cat interrupt" to view the current interrupt counter
use "echo 0 > interrupt" to clear interrupt counter
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix displaying of wrong channel information when user query
channel through debugfs
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For completeness, we should also make sure that the 3x3 MIMO rates are also checked when seeing if one rxon struct matches another.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to sync rxon_active with changes after we commit rxon_assoc,
without rxon_active will still have the old data that cause
iwl_send_rxon_assoc to fail with no change in rxon command.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug introduced by commit "iwlwifi: adding MIMO3 support
in rate scaling". We should not set the dual_stream_ant_msk (for 2x2 MIMO)
when using a 3x3 rate, this will cause a SYSASSERT in uCode.
Note: there is no triple_stream_ant_msk, because all three antennas are used.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adding MCS information in rate_scale_table, it help for
debugging rate scaling algorithm, easy to understand what is the current
rate scale table and matching modulation, plus the last mcs used for tx.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_mac_reset_tsf from iwlwifi.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_mac_get_tx_stats from iwlwifi.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_mac_config_interface from iwlwifi.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add config_ap lib op to iwlwifi and iwl3945 in preparation
of future 3945 porting actions.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_mac_config from iwlwifi
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_mac_remove_interface from iwlwifi
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can now use iwl_set_mode from iwlcore library.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add set_rxon_chain op to iwlwifi cfg ops in preparation of
future 3945 porting work.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl3945 can now use iwl_get_sta_id.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch unifies the add_station function for 3945 and iwlwifi drivers.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch replaces station function used in driver by station management ops
in 3945.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds declarations for station management ops to iwlwifi drivers.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delay mode setting till uCode is ready.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can use iwl_mac_beacon_update.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 can use iwl_bss_info_changed.
A new lib op is created for post_assoicate to distinguish between
3945 and iwlwifi's post_associate operations.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
libertas: add support for Marvell SD8688 chip
Use RxPD->pkt_ptr to locate eth803 header in the packet
received since SD8688/v10 firmware allows a gap between
RxPD and eth803 header.
Set SDIO block size to 256 for CMD53.
The maximum block size for SD8688 WLAN function is set
to 512 in TPLFE_MAX_BLK_SIZE. But using 512 as block size
results upto 2K bytes data (4 blocks) being transferred
and causes buffer overflow in firmware.
Both changes above are backward compatible with earlier
firmware versions for SD8385/SD8686.
The SDIO_DEVICE_IDs for SD8688 chip are added in
include/linux/mmc/sdio_ids.h
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
p54spi_wakeup and p54spi_tx_frame used busy-waiting loop
to poll for 'ready' bits in SPI_ADRS_HOST_INTERRUPTS register.
With this change in place 'WR_READY timeout' messages do not
show anymore.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for the LEDs on the Jupiter netbook.
Reported-by: Martin Bammer <mrb74@gmx.at>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the libertas main thread contends with the spi driver thread
in the TX path. To improve throughput, ensure that the driver thread
has higher scheduling priority than the libertas main thread. Do this
by making the libertas spi driver thread a low priority real time
thread.
We measured an average throughput improvement of 13%.
Signed-off-by: Anna Neal <anna@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adding few more debug messages if encounter error when driver
try to start tx aggregation queue. Also change from IWL_ERR to
IWL_DEBUG_HT is the HW legacy queue is empty when driver request to move
to aggregation queue.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Separated the MIMO tpt matrix into MIMO2 and MIMO3, adding MIMO3 support
in rate scaling algorithm. If the device support 3x3, then utilize all
three antenna (A/B/C) for tx to improve throughput.
Adding rs_switch_to_mimo3() function to allow switch to mimo3 modulation
mode from other modes(legacy/siso/mimo2). Adding rs_move_mimo3_to_other()
function to allow switch from mimo3 modulation mode to either siso or mimo2;
also support toggle between SGI and NGI.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding ht triple_stream_basic_rates for MIMO3 supports
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the EEPROM contains weird values for the power levels we have to
fix the interpolation process.
Signed-off-by: Fabio Rossi <rossi.f@inwind.it>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Auto-depend on HW_RANDOM, rather than "select"ing it.
This way the user has the choice to enable or disable HWRNG support.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces a new attribute for a wiphy that tells
userspace how long the information elements added to a probe
request frame can be at most. It also updates the at76 to
advertise that it cannot support that, and, for now until I
can fix that, iwlwifi too.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath5k/led.c:81:6: warning:
symbol 'ath5k_led_on' was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make ath5k select the ath module and add in the hooks to make the
eeprom regulatory hint and reg notifier take effect.
Changes to attach.c
Changes-licensed-under: ISC
Changes to base.c
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setup the wiphy regulatory parameters when first initializing the
Atheros regulatory module. We can remove five exported symbols this
way and simplify the driver code for both ath5k and ath9k.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change creates a new module, ath.ko, which includes code that can
be shared between ath5k, ath9k and ar9170. For now, extract most of the ath9k
regulatory code so it can also be used in ath5k.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All regulatory information is encapsulated by the ath9k_regulatory
struct, so we can now change all the callers to take that directly
instead of struct ath_hw. This in turn will enable us to move the
regulatory functions to common code also used by ath5k, since both
can use this regulatory struct.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Until ath5k and ath9k share common channel structures, they will have
to implement their own get_ctl() function. Split out the portion that
only relies on the current band and reg domain so that it can be common
code.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The STATUS_ALIVE value cannot be used because it is cleared when
interface is brought down and will not be set if rfkill is enabled when
interface is started again. The interface can thus not be brought up if
rfkill was enabled before stopping the interface and disabled after
starting the interface.
Change the test to use priv->is_open instead, this will be set when
interface is started whether rfkill is enabled or not.
Thanks to Helmut Schaa for the suggested fix.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert scan function to cfg80211. Unlike old scan code new code
waits 1 sec before getting scan data from device and passing
forward to cfg80211.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change quality level scale to match cfg80211 CFG80211_SIGNAL_TYPE_UNSPEC.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[edit: made rndis_change_virtual_intf static]
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds beacon filtering support to p54.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch hopefully finishes the SoftLED code:
- It adds two more LEDs (rx and radio).
(the FW claims it can support up to 16 LEDs,
but I doubt that any vendor put more than 4 on a board)
- update the LEDs in a _delayed_ workqueue.
No one reported any more crashes.
(see: "PATCH] p54: fix race condition in memory management")
So we can stop burning the mm code.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch rearrange and regroups most elements in p54_common.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Claiming every available 5 ghz channel has a couple of negative
side-effects: scanning takes a long time, and the channel list
overflows the available buffer space for netlink commands,
resulting in:
$ iw phy phy0 info
command failed: No buffer space available (-105)
This patch adds a modparam so people who want to see all the channels
can do so by passing all_channels=1. By default users will see a
smaller list of channels. This also halves scan time, from 10 seconds
down to less than 5 when using world regulatory.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Reported-by: Simon Farnsworth <simon@farnz.org.uk>
Tested-By: Simon Farnsworth <simon@farnz.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in checking for HT40 mode.
The STA's mode can be determined from the cached HT capabilities,
use that and remove the redundant variable 'rc_phy_mode'.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number of streams supported by a STA can be determined
directly from the HT capabilities. Remove the redundant
variable storing the stream cap.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up the ISR, removing a unnecessary do..while
loop, and waking up the chip before getting the pending
interrupts.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle aggregation params only when aggregation is
supported.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are unnecessary constructs in a function.
This patch removes these from both RX and TX init
routines.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never handle TIM, TIM_TIMER is used instead.
Remove this and the unnecessary swBeaconProcess variable.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jussi Kivilinna