On 32bit-UP u64_stats_fetch_begin() disables only preemption. If the
reader is in preemptible context and the writer side
(u64_stats_update_begin*()) runs in an interrupt context (IRQ or
softirq) then the writer can update the stats during the read operation.
This update remains undetected.
Use u64_stats_fetch_begin_irq() to ensure the stats fetch on 32bit-UP
are not interrupted by a writer. 32bit-SMP remains unaffected by this
change.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Catherine Sullivan <csully@google.com>
Cc: David Awogbemila <awogbemila@google.com>
Cc: Dimitris Michailidis <dmichail@fungible.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jeroen de Borst <jeroendb@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Simon Horman <simon.horman@corigine.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: oss-drivers@corigine.com
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* rtw88: operation, locking, warning, and code style fixes
* rtw89: small updates
* cfg80211/mac80211: more EHT/MLO (802.11be, WiFi 7) work
* brcmfmac: a couple of fixes
* misc cleanups etc.
-----BEGIN PGP SIGNATURE-----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=J5Fc
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-08-26-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes berg says:
====================
Various updates:
* rtw88: operation, locking, warning, and code style fixes
* rtw89: small updates
* cfg80211/mac80211: more EHT/MLO (802.11be, WiFi 7) work
* brcmfmac: a couple of fixes
* misc cleanups etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.
Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we add 6 GHz capability in MLO, we cannot use the SMPS
mode from the deflink. Pass it separately instead since on
a second link we don't even have a link data struct yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
From 'IEEE Std 802.11-2020 section 11.8.8.4.1':
The mesh channel switch may be triggered by the need to avoid
interference to a detected radar signal, or to reassign mesh STA
channels to ensure the MBSS connectivity.
A 20/40 MHz MBSS may be changed to a 20 MHz MBSS and a 20 MHz
MBSS may be changed to a 20/40 MHz MBSS.
Since the standard allows the change of bandwidth during
the channel switch in mesh, remove the bandwidth check present in
ieee80211_set_csa_beacon.
Fixes: c6da674aff ("{nl,cfg,mac}80211: enable the triggering of CSA frame in mesh")
Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com>
Link: https://lore.kernel.org/r/1658903549-21218-1-git-send-email-quic_haric@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 177577dbd2 ("wifi: mac80211: sta_info: fix link_sta insertion")
makes ieee80211_sta_activate_link() return 0 in the 'hash' label case.
Hence, setting ret in the !test_sta_flag(...) branch to zero is not needed
anymore and can be dropped.
Remove a needless assignment.
No functional change. No change in object code.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20220812103126.25308-1-lukas.bulwahn@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_tx_dequeue() we currently allow a control port
frame to be transmitted on a non-authorized port only if the
A2 matches the local interface address, but if that's an MLD
and the peer is a legacy peer, we need to allow link address
here. Fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For an AP interface, when userspace specifieds the link ID to
transmit the control port frame on (in particular for the
initial 4-way-HS), due to the logic in ieee80211_build_hdr()
for a frame transmitted from/to an MLD, we currently build a
header with
A1 = DA = MLD address of the peer MLD
A2 = local link address (!)
A3 = SA = local MLD address
This clearly makes no sense, and leads to two problems:
- if the frame were encrypted (not true for the initial
4-way-HS) the AAD would be calculated incorrectly
- if iTXQs are used, the frame is dropped by logic in
ieee80211_tx_dequeue()
Fix the addressing, which fixes the first bullet, and the
second bullet for peer MLDs, I'll fix the second one for
non-MLD peers separately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is simple here, and might save drivers some work if
they have common code for TX between beacons and other
frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To helper drivers if they e.g. have a lookup of the link_sta
pointer, add the link ID to the link_sta structure.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For AP/non-AP the EHT MCS/NSS subfield size differs, the
4-octet subfield is only used for 20 MHz-only non-AP STA.
Pass an argument around everywhere to be able to parse it
properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Draft P802.11be_D2.1, section 35.3.17 states that the EML Capabilities
Field shouldn't be included in case the device doesn't have support for
EMLSR or EMLMR.
Fixes: 81151ce462 ("wifi: mac80211: support MLO authentication/association with one link")
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When queuing frames to an interface store the link ID we
determined (which possibly came from the driver in the
RX status in the first place) in the RX status, and use
it in the MLME code to send probe responses, beacons and
CSA frames to the right link.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With link_id reported in rx_status for MLO connection, do the
stats update on the appropriate link instead of always deflink.
Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Link: https://lore.kernel.org/r/20220817104213.2531-3-quic_vthiagar@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In MLO, when the address translation from link to MLD is done
in fw/hw, it is necessary to be able to have some information
on the link on which the frame has been received. Extend the
rx API to include link_id and a valid flag in ieee80211_rx_status.
Also make chanes to mac80211 rx APIs to make use of the reported
link_id after sanity checks.
Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Link: https://lore.kernel.org/r/20220817104213.2531-2-quic_vthiagar@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement key installation and lookup (on TX and RX)
for MLO, so we can use multiple GTKs/IGTKs/BIGTKs.
Co-authored-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for various key operations on MLD by adding new parameter
link_id. Pass the link_id received from userspace to driver for add_key,
get_key, del_key, set_default_key, set_default_mgmt_key and
set_default_beacon_key to support configuring keys specific to each MLO
link. Userspace must not specify link ID for MLO pairwise key since it
is common for all the MLO links.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://lore.kernel.org/r/20220730052643.1959111-4-quic_vjakkam@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We've already freed the assoc_data at this point, so need
to use another copy of the AP (MLD) address instead.
Fixes: 81151ce462 ("wifi: mac80211: support MLO authentication/association with one link")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Configure the correct link per the passed parameters.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For an AP interface, set the link BSSID when the link
is initialized.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_sta_remove_link, valid_links is set to
the new_links before calling drv_change_sta_links, but
is used for the old_links.
Fixes: cb71f1d136 ("wifi: mac80211: add sta link addition/removal")
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there's no link ID, then check that there are no changes to
the link, and if so accept them, unless a new link is created.
While at it, reject creating a new link without an address.
This fixes authorizing an MLD (peer) that has no link 0.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ieee80211_lookup_ra_sta() function will sometimes set "sta" to NULL
so add this NULL check to prevent an Oops.
Fixes: 9dd1953846 ("wifi: nl80211/mac80211: clarify link ID in control port TX")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YuKcTAyO94YOy0Bu@kili
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add missing dev_kfree_skb() in an error path in
ieee80211_tx_control_port() to avoid a memory leak.
Fixes: dd820ed633 ("wifi: mac80211: return error from control port TX for drops")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220818043349.4168835-1-yangyingliang@huawei.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_scan_rx() tries to access scan_req->flags after a
null check, but a UAF is observed when the scan is completed
and __ieee80211_scan_completed() executes, which then calls
cfg80211_scan_done() leading to the freeing of scan_req.
Since scan_req is rcu_dereference()'d, prevent the racing in
__ieee80211_scan_completed() by ensuring that from mac80211's
POV it is no longer accessed from an RCU read critical section
before we call cfg80211_scan_done().
Cc: stable@vger.kernel.org
Link: https://syzkaller.appspot.com/bug?extid=f9acff9bf08a845f225d
Reported-by: syzbot+f9acff9bf08a845f225d@syzkaller.appspotmail.com
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Siddh Raman Pant <code@siddh.me>
Link: https://lore.kernel.org/r/20220819200340.34826-1-code@siddh.me
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- Runtime verification infrastructure
This is the biggest change for this pull request. It introduces the
runtime verification that is necessary for running Linux on safety
critical systems. It allows for deterministic automata models to be
inserted into the kernel that will attach to tracepoints, where the
information on these tracepoints will move the model from state to state.
If a state is encountered that does not belong to the model, it will then
activate a given reactor, that could just inform the user or even panic
the kernel (for which safety critical systems will detect and can recover
from).
- Two monitor models are also added: Wakeup In Preemptive (WIP - not to be
confused with "work in progress"), and Wakeup While Not Running (WWNR).
- Added __vstring() helper to the TRACE_EVENT() macro to replace several
vsnprintf() usages that were all doing it wrong.
- eprobes now can have their event autogenerated when the event name is left
off.
- The rest is various cleanups and fixes.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCYu0yzRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qj4HAP4tQtV55rjj4DQ5XIXmtI3/64PmyRSJ
+y4DEXi1UvEUCQD/QAuQfWoT/7gh35ltkfeS4t3ockzy14rrkP5drZigiQA=
=kEtM
-----END PGP SIGNATURE-----
Merge tag 'trace-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- Runtime verification infrastructure
This is the biggest change here. It introduces the runtime
verification that is necessary for running Linux on safety critical
systems.
It allows for deterministic automata models to be inserted into the
kernel that will attach to tracepoints, where the information on
these tracepoints will move the model from state to state.
If a state is encountered that does not belong to the model, it will
then activate a given reactor, that could just inform the user or
even panic the kernel (for which safety critical systems will detect
and can recover from).
- Two monitor models are also added: Wakeup In Preemptive (WIP - not to
be confused with "work in progress"), and Wakeup While Not Running
(WWNR).
- Added __vstring() helper to the TRACE_EVENT() macro to replace
several vsnprintf() usages that were all doing it wrong.
- eprobes now can have their event autogenerated when the event name is
left off.
- The rest is various cleanups and fixes.
* tag 'trace-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (50 commits)
rv: Unlock on error path in rv_unregister_reactor()
tracing: Use alignof__(struct {type b;}) instead of offsetof()
tracing/eprobe: Show syntax error logs in error_log file
scripts/tracing: Fix typo 'the the' in comment
tracepoints: It is CONFIG_TRACEPOINTS not CONFIG_TRACEPOINT
tracing: Use free_trace_buffer() in allocate_trace_buffers()
tracing: Use a struct alignof to determine trace event field alignment
rv/reactor: Add the panic reactor
rv/reactor: Add the printk reactor
rv/monitor: Add the wwnr monitor
rv/monitor: Add the wip monitor
rv/monitor: Add the wip monitor skeleton created by dot2k
Documentation/rv: Add deterministic automata instrumentation documentation
Documentation/rv: Add deterministic automata monitor synthesis documentation
tools/rv: Add dot2k
Documentation/rv: Add deterministic automaton documentation
tools/rv: Add dot2c
Documentation/rv: Add a basic documentation
rv/include: Add instrumentation helper functions
rv/include: Add deterministic automata monitor definition via C macros
...
Instead of open coding a __dynamic_array() with a fixed length (which
defeats the purpose of the dynamic array in the first place). Use the new
__vstring() helper that will use a va_list and only write enough of the
string into the ring buffer that is needed.
Link: https://lkml.kernel.org/r/20220705224751.271015450@goodmis.org
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
During the code reshuffling, I accidentally set this to
NULL before using it, fix that to fix the link data leak.
Fixes: d3e2439b0f ("wifi: mac80211: fix link manipulation")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In MLO we shouldn't call ieee80211_bss_info_change_notify(),
call that only (for backward compatibility) without MLO, and
otherwise ieee80211_vif_cfg_change_notify().
Similarly, ieee80211_reset_erp_info() only applies to the
current link, and in MLO we assume the driver doesn't really
need that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In sta_apply_parameters(), we really no longer need to
check that the link or sband exists, in fact, that's
harmful if link 0 doesn't exist, since then this will
fail.
Just remove this check, it was added for validation of
the sband where used, but it's not used here, it's now
only used in sta_link_apply_parameters() which has an
own lookup and check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To transmit the association frame to the right station and
with address translation, use the correct addresses there
and set up the AP address in the configuration earlier so
it's applied during the transmit of auth/assoc frames.
Fixes: 81151ce462 ("wifi: mac80211: support MLO authentication/association with one link")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll need the link e.g. for decrypt, and shouldn't be
looking it up all the time later, so track it in the RX
data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For drivers using software encryption for multicast TX, such
as mac80211_hwsim, mac80211 needs to duplicate the multicast
frames on each link, if MLO is enabled. Do this, but don't
just make it dependent on the key but provide a separate flag
for drivers to opt out of this.
This is not very efficient, I expect that drivers will do it
in firmware/hardware or at least with DMA engine assistence,
so this is mostly for hwsim.
To make this work, also implement the SNS11 sequence number
space that an AP MLD shall have, and modify the API to the
__ieee80211_subif_start_xmit() function to always require the
link ID bits to be set.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a couple of new things that should be possible
with MLO:
* selecting the link to transmit to a station by link ID,
which a previous patch added to the nl80211 API
* selecting the link by frequency, similarly
* allowing transmittion to an MLD without specifying any
channel or link ID, with MLD addresses
Enable these use cases. Also fix the address comparison
in client mode to use the AP (MLD) address.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the low level driver reports hardware timestamps for frame
TX status or frame RX, pass the timestamps to cfg80211.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When inserting a link STA, make sure it doesn't exist first
and add lockdep assertions that we cannot modify the hash
table without holding the sta_mtx, so this check is really
correct.
Also return without hashing if the driver failed, and warn
if the hashing fails, which shouldn't happen due to the
check described above.
Fixes: cb71f1d136 ("wifi: mac80211: add sta link addition/removal")
Fixes: ba6ddab94f ("wifi: mac80211: maintain link-sta hash table")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to copy the address to both the private and public
portion of the link_sta (the private one is needed for the
hash table). Fix this.
Fixes: bbe90107e1 ("wifi: mac80211: mlme: refactor link station setup")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clarify the link ID behaviour in control port TX, we need it
to select the link to transmit on for both MLD and non-MLD
receivers, but select the link address as the SA only if the
receiver is not an MLD.
Fixes: 67207bab93 ("wifi: cfg80211/mac80211: Support control port TX from specific link")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the frame is going to be dropped anyway because
ieee80211_lookup_ra_sta() returned an error (and
even though it's a bit racy, it will likely continue
to do so), return the error out instead of just
silently dropping the frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add more sanity checks to the API handling, we shouldn't
be able to create a station without links, nor should we
be able to add a link to a station that wasn't created as
an MLD with links in the first place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are two issues here: we unhash the link stations only
directly before freeing the station they belong to, and we
also don't unhash all the links correctly in all cases. Fix
these issues.
Fixes: ba6ddab94f ("wifi: mac80211: maintain link-sta hash table")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When modifying a link station, validate that the link address
doesn't change, except the first time the link is created.
Fixes: b95eb7f0ee ("wifi: cfg80211/mac80211: separate link params from station params")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At this point, we've already changed link_id to be zero for
a non-MLO connection, so use the 'mlo' variable rather than
link ID to determine the MLO status of the station.
Fixes: bd363ee533 ("wifi: mac80211: mlme: set sta.mlo correctly")
Fixes: 81151ce462 ("wifi: mac80211: support MLO authentication/association with one link")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there's a non-MLO client, the A2 must be set to the BSSID
of the link since no translation will happen in lower layers
and it's needed that way for encryption.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should only translate addr3 here if it's the BSSID.
Fixes: 42fb9148c0 ("wifi: mac80211: do link->MLD address translation on RX")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we have a non-MLD STA on an AP MLD, we crash while
adding the station. Fix that, in this case we need to
use the STA's address also on the link data structure.
Fixes: f36fe0a2df ("wifi: mac80211: fix up link station creation/insertion")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In my previous changes here, I neglected to take the old
conn_flags into account that might still be present from
the authentication, and thus ieee80211_setup_assoc_link()
can misbehave, as well as the override calculation being
wrong. Fix that by ORing in the old flags.
Fixes: 1845c1d4a4 ("wifi: mac80211: mlme: refactor assoc link setup")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In a few places we need to use the AP (MLD) address, not the
deflink BSSID, the link address translation will happen later.
To make that work properly for fast-xmit, set up the ap_addr
in the vif.cfg earlier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
lockdep complains use of uninitialized spinlock at ieee80211_do_stop() [1],
for commit f856373e2f ("wifi: mac80211: do not wake queues on a vif
that is being stopped") guards clear_bit() using fq.lock even before
fq_init() from ieee80211_txq_setup_flows() initializes this spinlock.
According to discussion [2], Toke was not happy with expanding usage of
fq.lock. Since __ieee80211_wake_txqs() is called under RCU read lock, we
can instead use synchronize_rcu() for flushing ieee80211_wake_txqs().
Link: https://syzkaller.appspot.com/bug?extid=eceab52db7c4b961e9d6 [1]
Link: https://lkml.kernel.org/r/874k0zowh2.fsf@toke.dk [2]
Reported-by: syzbot <syzbot+eceab52db7c4b961e9d6@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: f856373e2f ("wifi: mac80211: do not wake queues on a vif that is being stopped")
Tested-by: syzbot <syzbot+eceab52db7c4b961e9d6@syzkaller.appspotmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/9cc9b81d-75a3-3925-b612-9d0ad3cab82b@I-love.SAKURA.ne.jp
Due to some changes and rebasing between different patches
this fell through the cracks; we need to set sta.mlo if the
connection is using MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It might seem a bit pointless to do a multi-link operation
connection with just a single link, but this is already a
big change, so for now, limit MLO connections to a single
link.
Extending that to multiple links will require
* work on parsing the multi-link element with STA profile
properly, including element fragmentation;
* checking the per-link status in the multi-link element
* implementing logic to have active/inactive links to let
drivers decide which links should be active;
* implementing multicast RX deduplication;
* and likely more.
For now this is still useful since it lets us do multi-link
connections for the purposes of testing APIs and the higher
layers such as wpa_supplicant.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the necessary API to parse the multi-link element in
the future. For now, link only to the element when found
so we can use it in the client-side code later.
Later, we'll need to fill this in to deal with element
fragmentation, parse the STA profile, etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, e.g. with Qualcomm devices and management
frames, or in hwsim, frames may be reported from the driver
with link addresses, but for decryption and matching needs
we really want to have them with MLD addresses. Support the
translation on RX.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an MLO AP is transmitting to a non-MLO station, addr2 should be set
to a link address. This should be done before the frame is encrypted as
otherwise aad verification would fail. In case of software encryption
this can't be left for the device to handle, and should be done by
mac80211 when building the frame hdr.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we create a station with a non-default link, then
we should have a link address, and we definitely need
to insert it into the link hash table on insertion.
Split the API into with and without link creation and
if it has a link, insert the link into the link hash
table on sta_info_insert().
Fixes: ba6ddab94f ("wifi: mac80211: maintain link-sta hash table")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In AP/mesh where the stations are added by userspace, we
limit the number of A-MSDU subframes according to the
extended capabilities.
Refactor the code and extend that also to client-side.
Fixes: 506bcfa8ab ("mac80211: limit the A-MSDU Tx based on peer's capabilities")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split out much of the code in ieee80211_set_associated()
into a new ieee80211_link_set_associated() which can be
called per link later for MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If NEED_DTIM_BEFORE_ASSOC isn't set, then we don't need
to enter an RCU critical section and look up the beacon
elements.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Factor out the code to set up the assoc link into a
new function ieee80211_setup_assoc_link().
While at it, also modify the 'override' handling to
just take into account whether or not the conn_flags
were changed, which is what we need to setup again
the channel later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to pass the address, we can look at the auth_data
inside the function rather than outside.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor the per-link setup out of ieee80211_assoc_success()
into a new function ieee80211_assoc_config_link().
It looks useless for now to parse the elements again inside
ieee80211_assoc_config_link(), but that will be done with
the link ID in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor ieee80211_prep_channel() to make the link argument
optional and add a conn_flags pointer argument instead, so
that we can later use this for links that don't exist yet
to build the right information for MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For MLO, we will need to build these elements per link, so
factor out the code that does this, returning the capability,
to simplify building the multi-link element in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With MLO, when we'll disconnect from an AP MLD, we'll just
destroy all the links. Therefore, the only thing we (may)
need to reset is the deflink data, so switch back to that
and adjust the comments accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For MLO we'll need to read flags not directly from the link as
it may not even exist yet if we're just setting up flags for
a secondary link before sending the association request, so
pass the incoming conn_flags separately. Also, while at it,
pass the sdata/link separately as for non-tracking now the
link may be NULL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll need ieee80211_prep_channel() in other code for MLO
later, so move the code up - unchanged for now - to avoid
forward declarations in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor the code here since we need to have it also for each
link station after association in MLO later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The flag here is currently per interface, but the way we
set and clear it means it should be per link, so change
it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When sending an authentication frame from an MLD, include
the multi-link element with the MLD address and use the
link address for transmission.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clean up the code building the supported channels element
a little bit by using a local variable instead of the long
line.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For now, prohibit DEAUTH_NEED_MGD_TX_PREP since we can't
really transmit this on a specific link yet as we don't
know which links are active.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since struct ieee80211_bss_conf already contains link_id,
passing link_id is not necessary.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since mac80211 already has a protected pointer to link_conf,
pass it to the driver to avoid additional RCU locking.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Recalculate min channel context for the given or all interface
links, depending on the caller. For a station state change, we
need to recalculate all of them since we don't know which link
(or multiple) it might be on.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We check here that we don't enable TX (netif_carrier_ok())
before we actually start using some channel context, but to
our knowledge this check has never triggered, and with MLO
it's just wrong since links can be added and removed much
more dynamically than before.
Simply remove the checks, there's no really good way to do
anything that would replace them.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow link source address on TX.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow transmitting EAPOL frames not only from the interface
address (which is the MLD address) but also any link addresses,
in order to support non-MLO stations on AP interfaces.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of authentication with a legacy station, link addressed EAPOL
frames should be sent. Support it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The way this works is that you add all the element data,
keeping a pointer to the length field of the element.
Then call this helper function, which will fragment the
element if there was more than 255 bytes in the element,
memmove()ing the data back if needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For now, skip rate statistics here to avoid warnings in
the called code, we'll need to adjust this to have all
the statistics for link stations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we add non-deflink pointers, we need to remove the
link[0] pointer to deflink in case link[0] is not valid
afterwards. Also, we need to add that back when there
are no more valid links. Reorg the code to fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we remove a link that doesn't have a channel context,
we don't really need the local->mtx locking. Tighten the
check here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to consider the (maximum) size of the EHT element
we'll add for the association request, otherwise we may run
out of space.
Fixes: 820acc810f ("mac80211: Add EHT capabilities to association/probe request")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The functions currently take a link and check data
from it, but this needs to change for MLO. Simplify
the prototypes by passing only the needed arguments.
Remove the regulatory checks, the warnings shouldn't
trigger, and haven't as far as I know.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rework the sorting of custom elements into the association
request by moving the elements before HT/VHT/HE to each
their own function. While at it, fix the placement of the
ones that should be between VHT and HE.
This doesn't fix the placement of elements that should be
between HE and EHT yet, a similar change might be needed
in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's some awkward code that really only exists
because we want to optimize the allocation size,
but that's not really all that necessary.
Refactor the code that adds rates to the association
request frame to have a separate function, removing
the goto.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Here, ext_capa is checked and can only be non-NULL if
assoc_data->ie_len was set before, so the check here
is redundant.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to handle the link addresses for station differently,
they will be determined by the association code, stored, and
then applied when the links are actually created on success,
cfg80211 will fill in the right addresses per the data we're
sending back to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jakub Kicinski